* [PATCH 2/2] sata_rcar: Add R-Car Gen2 SATA PHY support
2013-10-15 10:20 [PATCH 0/2] sata_rcar: Adjust DT bindings and add R-Car Gen2 PHY support (take 2) Valentine Barshak
@ 2013-10-15 10:20 ` Valentine Barshak
0 siblings, 0 replies; 12+ messages in thread
From: Valentine Barshak @ 2013-10-15 10:20 UTC (permalink / raw)
To: linux-sh, linux-ide, devicetree
Cc: Simon Horman, Magnus Damm, Vladimir Barinov, Sergei Shtylyov,
Kuninori Morimoto, Laurent Pinchart, Guennadi Liakhovetski,
Tejun Heo, Mark Rutland
R-Car Gen2 SoCs have a different PHY which is not compatible
with the older R-Car H1 (R8A7779) version.
This adds OF/platform device id tables and PHY initialization
callbacks for the following Gen2 SoCs:
* R-Car H2: R8A7790;
* R-Car M2: R8A7791.
PHY initialization method is chosen based on the device id.
Default PHY settings are applied for Gen2 SoCs, which should
suit the Gen2 boards available.
The R8A7779 platform code is modified to use "sata-r8a7779"
device name.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
---
.../devicetree/bindings/ata/sata_rcar.txt | 5 +-
arch/arm/mach-shmobile/clock-r8a7779.c | 2 +-
arch/arm/mach-shmobile/setup-r8a7779.c | 2 +-
drivers/ata/sata_rcar.c | 118 ++++++++++++++++++---
4 files changed, 107 insertions(+), 20 deletions(-)
diff --git a/Documentation/devicetree/bindings/ata/sata_rcar.txt b/Documentation/devicetree/bindings/ata/sata_rcar.txt
index 0719115..d6b20a6 100644
--- a/Documentation/devicetree/bindings/ata/sata_rcar.txt
+++ b/Documentation/devicetree/bindings/ata/sata_rcar.txt
@@ -1,7 +1,10 @@
* Renesas R-Car SATA
Required properties:
-- compatible : should contain "renesas,sata-r8a7779";
+- compatible : should contain one of the following:
+ - "renesas,sata-r8a7779" for R-Car H1
+ - "renesas,sata-r8a7790" for R-Car H2
+ - "renesas,sata-r8a7791" for R-Car M2
- reg : offset and length of the SATA registers;
- interrupts : must consist of one interrupt specifier.
diff --git a/arch/arm/mach-shmobile/clock-r8a7779.c b/arch/arm/mach-shmobile/clock-r8a7779.c
index badb8b7..6593237 100644
--- a/arch/arm/mach-shmobile/clock-r8a7779.c
+++ b/arch/arm/mach-shmobile/clock-r8a7779.c
@@ -170,7 +170,7 @@ static struct clk_lookup lookups[] = {
/* MSTP32 clocks */
CLKDEV_DEV_ID("r8a7779-vin.3", &mstp_clks[MSTP120]), /* VIN3 */
CLKDEV_DEV_ID("rcar-pcie", &mstp_clks[MSTP116]), /* PCIe */
- CLKDEV_DEV_ID("sata_rcar", &mstp_clks[MSTP115]), /* SATA */
+ CLKDEV_DEV_ID("sata-r8a7779", &mstp_clks[MSTP115]), /* SATA */
CLKDEV_DEV_ID("fc600000.sata", &mstp_clks[MSTP115]), /* SATA w/DT */
CLKDEV_DEV_ID("r8a777x-ether", &mstp_clks[MSTP114]), /* Ether */
CLKDEV_DEV_ID("r8a7779-vin.0", &mstp_clks[MSTP110]), /* VIN0 */
diff --git a/arch/arm/mach-shmobile/setup-r8a7779.c b/arch/arm/mach-shmobile/setup-r8a7779.c
index 13049e9..6aac99e 100644
--- a/arch/arm/mach-shmobile/setup-r8a7779.c
+++ b/arch/arm/mach-shmobile/setup-r8a7779.c
@@ -438,7 +438,7 @@ static struct resource sata_resources[] = {
};
static struct platform_device sata_device = {
- .name = "sata_rcar",
+ .name = "sata-r8a7779",
.id = -1,
.resource = sata_resources,
.num_resources = ARRAY_SIZE(sata_resources),
diff --git a/drivers/ata/sata_rcar.c b/drivers/ata/sata_rcar.c
index a625cc5..068d5b4 100644
--- a/drivers/ata/sata_rcar.c
+++ b/drivers/ata/sata_rcar.c
@@ -15,6 +15,7 @@
#include <linux/module.h>
#include <linux/ata.h>
#include <linux/libata.h>
+#include <linux/of_device.h>
#include <linux/platform_device.h>
#include <linux/clk.h>
#include <linux/err.h>
@@ -123,12 +124,37 @@
#define SATA_RCAR_DMA_BOUNDARY 0x1FFFFFFEUL
+/* Gen2 Physical Layer Control Registers */
+#define RCAR_GEN2_PHY_CTL1_REG 0x1704
+#define RCAR_GEN2_PHY_CTL1 0x34180002
+#define RCAR_GEN2_PHY_CTL1_SS 0xC180 /* Spread Spectrum */
+
+#define RCAR_GEN2_PHY_CTL2_REG 0x170C
+#define RCAR_GEN2_PHY_CTL2 0x00002303
+
+#define RCAR_GEN2_PHY_CTL3_REG 0x171C
+#define RCAR_GEN2_PHY_CTL3 0x000B0194
+
+#define RCAR_GEN2_PHY_CTL4_REG 0x1724
+#define RCAR_GEN2_PHY_CTL4 0x00030994
+
+#define RCAR_GEN2_PHY_CTL5_REG 0x1740
+#define RCAR_GEN2_PHY_CTL5 0x03004001
+#define RCAR_GEN2_PHY_CTL5_DC BIT(1) /* DC connection */
+#define RCAR_GEN2_PHY_CTL5_TR BIT(2) /* Termination Resistor */
+
+enum sata_rcar_type {
+ RCAR_GEN1_SATA,
+ RCAR_GEN2_SATA,
+};
+
struct sata_rcar_priv {
void __iomem *base;
struct clk *clk;
+ enum sata_rcar_type type;
};
-static void sata_rcar_phy_initialize(struct sata_rcar_priv *priv)
+static void sata_rcar_gen1_phy_preinit(struct sata_rcar_priv *priv)
{
void __iomem *base = priv->base;
@@ -141,8 +167,8 @@ static void sata_rcar_phy_initialize(struct sata_rcar_priv *priv)
iowrite32(0, base + SATAPHYRESET_REG);
}
-static void sata_rcar_phy_write(struct sata_rcar_priv *priv, u16 reg, u32 val,
- int group)
+static void sata_rcar_gen1_phy_write(struct sata_rcar_priv *priv, u16 reg,
+ u32 val, int group)
{
void __iomem *base = priv->base;
int timeout;
@@ -170,6 +196,29 @@ static void sata_rcar_phy_write(struct sata_rcar_priv *priv, u16 reg, u32 val,
iowrite32(0, base + SATAPHYADDR_REG);
}
+static void sata_rcar_gen1_phy_init(struct sata_rcar_priv *priv)
+{
+ sata_rcar_gen1_phy_preinit(priv);
+ sata_rcar_gen1_phy_write(priv, SATAPCTLR1_REG, 0x00200188, 0);
+ sata_rcar_gen1_phy_write(priv, SATAPCTLR1_REG, 0x00200188, 1);
+ sata_rcar_gen1_phy_write(priv, SATAPCTLR3_REG, 0x0000A061, 0);
+ sata_rcar_gen1_phy_write(priv, SATAPCTLR2_REG, 0x20000000, 0);
+ sata_rcar_gen1_phy_write(priv, SATAPCTLR2_REG, 0x20000000, 1);
+ sata_rcar_gen1_phy_write(priv, SATAPCTLR4_REG, 0x28E80000, 0);
+}
+
+static void sata_rcar_gen2_phy_init(struct sata_rcar_priv *priv)
+{
+ void __iomem *base = priv->base;
+
+ iowrite32(RCAR_GEN2_PHY_CTL1, base + RCAR_GEN2_PHY_CTL1_REG);
+ iowrite32(RCAR_GEN2_PHY_CTL2, base + RCAR_GEN2_PHY_CTL2_REG);
+ iowrite32(RCAR_GEN2_PHY_CTL3, base + RCAR_GEN2_PHY_CTL3_REG);
+ iowrite32(RCAR_GEN2_PHY_CTL4, base + RCAR_GEN2_PHY_CTL4_REG);
+ iowrite32(RCAR_GEN2_PHY_CTL5 | RCAR_GEN2_PHY_CTL5_DC |
+ RCAR_GEN2_PHY_CTL5_TR, base + RCAR_GEN2_PHY_CTL5_REG);
+}
+
static void sata_rcar_freeze(struct ata_port *ap)
{
struct sata_rcar_priv *priv = ap->host->private_data;
@@ -738,13 +787,17 @@ static void sata_rcar_init_controller(struct ata_host *host)
u32 val;
/* reset and setup phy */
- sata_rcar_phy_initialize(priv);
- sata_rcar_phy_write(priv, SATAPCTLR1_REG, 0x00200188, 0);
- sata_rcar_phy_write(priv, SATAPCTLR1_REG, 0x00200188, 1);
- sata_rcar_phy_write(priv, SATAPCTLR3_REG, 0x0000A061, 0);
- sata_rcar_phy_write(priv, SATAPCTLR2_REG, 0x20000000, 0);
- sata_rcar_phy_write(priv, SATAPCTLR2_REG, 0x20000000, 1);
- sata_rcar_phy_write(priv, SATAPCTLR4_REG, 0x28E80000, 0);
+ switch (priv->type) {
+ case RCAR_GEN1_SATA:
+ sata_rcar_gen1_phy_init(priv);
+ break;
+ case RCAR_GEN2_SATA:
+ sata_rcar_gen2_phy_init(priv);
+ break;
+ default:
+ dev_warn(host->dev, "SATA phy is not initialized\n");
+ break;
+ }
/* SATA-IP reset state */
val = ioread32(base + ATAPI_CONTROL1_REG);
@@ -770,8 +823,39 @@ static void sata_rcar_init_controller(struct ata_host *host)
iowrite32(ATAPI_INT_ENABLE_SATAINT, base + ATAPI_INT_ENABLE_REG);
}
+static struct of_device_id sata_rcar_match[] = {
+ /* Deprecated, "renesas,sata-r8a7779" should be used instead. */
+ {
+ .compatible = "renesas,rcar-sata",
+ .data = (void *)RCAR_GEN1_SATA,
+ },
+ {
+ .compatible = "renesas,sata-r8a7779",
+ .data = (void *)RCAR_GEN1_SATA,
+ },
+ {
+ .compatible = "renesas,sata-r8a7790",
+ .data = (void *)RCAR_GEN2_SATA
+ },
+ {
+ .compatible = "renesas,sata-r8a7791",
+ .data = (void *)RCAR_GEN2_SATA
+ },
+ {},
+};
+MODULE_DEVICE_TABLE(of, sata_rcar_match);
+
+static const struct platform_device_id sata_rcar_id_table[] = {
+ { "sata-r8a7779", RCAR_GEN1_SATA },
+ { "sata-r8a7790", RCAR_GEN2_SATA },
+ { "sata-r8a7791", RCAR_GEN2_SATA },
+ { },
+};
+MODULE_DEVICE_TABLE(platform, sata_rcar_id_table);
+
static int sata_rcar_probe(struct platform_device *pdev)
{
+ const struct of_device_id *of_id;
struct ata_host *host;
struct sata_rcar_priv *priv;
struct resource *mem;
@@ -787,6 +871,12 @@ static int sata_rcar_probe(struct platform_device *pdev)
if (!priv)
return -ENOMEM;
+ of_id = of_match_device(sata_rcar_match, &pdev->dev);
+ if (of_id)
+ priv->type = (enum sata_rcar_type)of_id->data;
+ else
+ priv->type = platform_get_device_id(pdev)->driver_data;
+
priv->clk = devm_clk_get(&pdev->dev, NULL);
if (IS_ERR(priv->clk)) {
dev_err(&pdev->dev, "failed to get access to sata clock\n");
@@ -892,16 +982,10 @@ static const struct dev_pm_ops sata_rcar_pm_ops = {
};
#endif
-static struct of_device_id sata_rcar_match[] = {
- { .compatible = "renesas,rcar-sata", }, /* Deprecated */
- { .compatible = "renesas,sata-r8a7779", },
- {},
-};
-MODULE_DEVICE_TABLE(of, sata_rcar_match);
-
static struct platform_driver sata_rcar_driver = {
.probe = sata_rcar_probe,
.remove = sata_rcar_remove,
+ .id_table = sata_rcar_id_table,
.driver = {
.name = DRV_NAME,
.owner = THIS_MODULE,
--
1.8.3.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 0/2] sata_rcar: Adjust DT bindings and add R-Car Gen2 PHY support (take 3)
@ 2013-10-16 12:05 Valentine Barshak
2013-10-16 12:06 ` [PATCH 1/2] sata_rcar: Adjust and document device tree bindings Valentine Barshak
2013-10-16 12:06 ` [PATCH 2/2] sata_rcar: Add R-Car Gen2 SATA PHY support Valentine Barshak
0 siblings, 2 replies; 12+ messages in thread
From: Valentine Barshak @ 2013-10-16 12:05 UTC (permalink / raw)
To: linux-sh, linux-ide, devicetree
Cc: Simon Horman, Magnus Damm, Vladimir Barinov, Sergei Shtylyov,
Kuninori Morimoto, Laurent Pinchart, Guennadi Liakhovetski,
Tejun Heo, Mark Rutland
This modifies and documents R-Car SATA device tree (DT) bindings.
The "sata-<SoC>" format is now used for the "compatible" property.
Also, a platform device id table is introduced for non-DT support.
The device id naming is consistent with the "compatible" DT
property format.
R-Car Gen2 SATA PHY support is added. PHY initialization method
is chosen, based on the device id.
Changes from version 1:
* Kept old DT bindings for compatibility
* Amended DT bindings documentation
Changes from version 2:
* Dropped r8a7779.dtsi changes
Valentine Barshak (2):
sata_rcar: Adjust and document device tree bindings
sata_rcar: Add R-Car Gen2 SATA support
.../devicetree/bindings/ata/sata_rcar.txt | 19 ++++
arch/arm/boot/dts/r8a7779.dtsi | 2 +-
arch/arm/mach-shmobile/clock-r8a7779.c | 2 +-
arch/arm/mach-shmobile/setup-r8a7779.c | 2 +-
drivers/ata/sata_rcar.c | 112 ++++++++++++++++++---
5 files changed, 118 insertions(+), 19 deletions(-)
create mode 100644 Documentation/devicetree/bindings/ata/sata_rcar.txt
--
1.8.3.1
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH 1/2] sata_rcar: Adjust and document device tree bindings
2013-10-16 12:05 [PATCH 0/2] sata_rcar: Adjust DT bindings and add R-Car Gen2 PHY support (take 3) Valentine Barshak
@ 2013-10-16 12:06 ` Valentine Barshak
2013-10-16 12:06 ` [PATCH 2/2] sata_rcar: Add R-Car Gen2 SATA PHY support Valentine Barshak
1 sibling, 0 replies; 12+ messages in thread
From: Valentine Barshak @ 2013-10-16 12:06 UTC (permalink / raw)
To: linux-sh, linux-ide, devicetree
Cc: Simon Horman, Magnus Damm, Vladimir Barinov, Sergei Shtylyov,
Kuninori Morimoto, Laurent Pinchart, Guennadi Liakhovetski,
Tejun Heo, Mark Rutland
This deprecates the "rcar-sata" compatibility string
and adds the "sata-r8a7779" which complies to the
preferred <unit>-<soc> format for SH-Mobile devices.
The DT bindings are documented.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
---
Documentation/devicetree/bindings/ata/sata_rcar.txt | 15 +++++++++++++++
drivers/ata/sata_rcar.c | 3 ++-
2 files changed, 17 insertions(+), 1 deletion(-)
create mode 100644 Documentation/devicetree/bindings/ata/sata_rcar.txt
diff --git a/Documentation/devicetree/bindings/ata/sata_rcar.txt b/Documentation/devicetree/bindings/ata/sata_rcar.txt
new file mode 100644
index 0000000..0719115
--- /dev/null
+++ b/Documentation/devicetree/bindings/ata/sata_rcar.txt
@@ -0,0 +1,15 @@
+* Renesas R-Car SATA
+
+Required properties:
+- compatible : should contain "renesas,sata-r8a7779";
+- reg : offset and length of the SATA registers;
+- interrupts : must consist of one interrupt specifier.
+
+Example:
+
+sata: sata@fc600000 {
+ compatible = "renesas,sata-r8a7779";
+ reg = <0xfc600000 0x2000>;
+ interrupt-parent = <&gic>;
+ interrupts = <0 100 0x4>;
+};
diff --git a/drivers/ata/sata_rcar.c b/drivers/ata/sata_rcar.c
index c2d95e9..a625cc5 100644
--- a/drivers/ata/sata_rcar.c
+++ b/drivers/ata/sata_rcar.c
@@ -893,7 +893,8 @@ static const struct dev_pm_ops sata_rcar_pm_ops = {
#endif
static struct of_device_id sata_rcar_match[] = {
- { .compatible = "renesas,rcar-sata", },
+ { .compatible = "renesas,rcar-sata", }, /* Deprecated */
+ { .compatible = "renesas,sata-r8a7779", },
{},
};
MODULE_DEVICE_TABLE(of, sata_rcar_match);
--
1.8.3.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [PATCH 2/2] sata_rcar: Add R-Car Gen2 SATA PHY support
2013-10-16 12:05 [PATCH 0/2] sata_rcar: Adjust DT bindings and add R-Car Gen2 PHY support (take 3) Valentine Barshak
2013-10-16 12:06 ` [PATCH 1/2] sata_rcar: Adjust and document device tree bindings Valentine Barshak
@ 2013-10-16 12:06 ` Valentine Barshak
2013-10-29 4:59 ` Simon Horman
1 sibling, 1 reply; 12+ messages in thread
From: Valentine Barshak @ 2013-10-16 12:06 UTC (permalink / raw)
To: linux-sh, linux-ide, devicetree
Cc: Simon Horman, Magnus Damm, Vladimir Barinov, Sergei Shtylyov,
Kuninori Morimoto, Laurent Pinchart, Guennadi Liakhovetski,
Tejun Heo, Mark Rutland
R-Car Gen2 SoCs have a different PHY which is not compatible
with the older R-Car H1 (R8A7779) version.
This adds OF/platform device id tables and PHY initialization
callbacks for the following Gen2 SoCs:
* R-Car H2: R8A7790;
* R-Car M2: R8A7791.
PHY initialization method is chosen based on the device id.
Default PHY settings are applied for Gen2 SoCs, which should
suit the Gen2 boards available.
The R8A7779 platform code is modified to use "sata-r8a7779"
device name.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
---
.../devicetree/bindings/ata/sata_rcar.txt | 5 +-
arch/arm/mach-shmobile/clock-r8a7779.c | 2 +-
arch/arm/mach-shmobile/setup-r8a7779.c | 2 +-
drivers/ata/sata_rcar.c | 118 ++++++++++++++++++---
4 files changed, 107 insertions(+), 20 deletions(-)
diff --git a/Documentation/devicetree/bindings/ata/sata_rcar.txt b/Documentation/devicetree/bindings/ata/sata_rcar.txt
index 0719115..d6b20a6 100644
--- a/Documentation/devicetree/bindings/ata/sata_rcar.txt
+++ b/Documentation/devicetree/bindings/ata/sata_rcar.txt
@@ -1,7 +1,10 @@
* Renesas R-Car SATA
Required properties:
-- compatible : should contain "renesas,sata-r8a7779";
+- compatible : should contain one of the following:
+ - "renesas,sata-r8a7779" for R-Car H1
+ - "renesas,sata-r8a7790" for R-Car H2
+ - "renesas,sata-r8a7791" for R-Car M2
- reg : offset and length of the SATA registers;
- interrupts : must consist of one interrupt specifier.
diff --git a/arch/arm/mach-shmobile/clock-r8a7779.c b/arch/arm/mach-shmobile/clock-r8a7779.c
index 5c83259..b2f8417 100644
--- a/arch/arm/mach-shmobile/clock-r8a7779.c
+++ b/arch/arm/mach-shmobile/clock-r8a7779.c
@@ -170,7 +170,7 @@ static struct clk_lookup lookups[] = {
/* MSTP32 clocks */
CLKDEV_DEV_ID("r8a7779-vin.3", &mstp_clks[MSTP120]), /* VIN3 */
CLKDEV_DEV_ID("rcar-pcie", &mstp_clks[MSTP116]), /* PCIe */
- CLKDEV_DEV_ID("sata_rcar", &mstp_clks[MSTP115]), /* SATA */
+ CLKDEV_DEV_ID("sata-r8a7779", &mstp_clks[MSTP115]), /* SATA */
CLKDEV_DEV_ID("fc600000.sata", &mstp_clks[MSTP115]), /* SATA w/DT */
CLKDEV_DEV_ID("r8a777x-ether", &mstp_clks[MSTP114]), /* Ether */
CLKDEV_DEV_ID("r8a7779-vin.0", &mstp_clks[MSTP110]), /* VIN0 */
diff --git a/arch/arm/mach-shmobile/setup-r8a7779.c b/arch/arm/mach-shmobile/setup-r8a7779.c
index 51a43c5..9d49090 100644
--- a/arch/arm/mach-shmobile/setup-r8a7779.c
+++ b/arch/arm/mach-shmobile/setup-r8a7779.c
@@ -438,7 +438,7 @@ static struct resource sata_resources[] = {
};
static struct platform_device sata_device = {
- .name = "sata_rcar",
+ .name = "sata-r8a7779",
.id = -1,
.resource = sata_resources,
.num_resources = ARRAY_SIZE(sata_resources),
diff --git a/drivers/ata/sata_rcar.c b/drivers/ata/sata_rcar.c
index a625cc5..068d5b4 100644
--- a/drivers/ata/sata_rcar.c
+++ b/drivers/ata/sata_rcar.c
@@ -15,6 +15,7 @@
#include <linux/module.h>
#include <linux/ata.h>
#include <linux/libata.h>
+#include <linux/of_device.h>
#include <linux/platform_device.h>
#include <linux/clk.h>
#include <linux/err.h>
@@ -123,12 +124,37 @@
#define SATA_RCAR_DMA_BOUNDARY 0x1FFFFFFEUL
+/* Gen2 Physical Layer Control Registers */
+#define RCAR_GEN2_PHY_CTL1_REG 0x1704
+#define RCAR_GEN2_PHY_CTL1 0x34180002
+#define RCAR_GEN2_PHY_CTL1_SS 0xC180 /* Spread Spectrum */
+
+#define RCAR_GEN2_PHY_CTL2_REG 0x170C
+#define RCAR_GEN2_PHY_CTL2 0x00002303
+
+#define RCAR_GEN2_PHY_CTL3_REG 0x171C
+#define RCAR_GEN2_PHY_CTL3 0x000B0194
+
+#define RCAR_GEN2_PHY_CTL4_REG 0x1724
+#define RCAR_GEN2_PHY_CTL4 0x00030994
+
+#define RCAR_GEN2_PHY_CTL5_REG 0x1740
+#define RCAR_GEN2_PHY_CTL5 0x03004001
+#define RCAR_GEN2_PHY_CTL5_DC BIT(1) /* DC connection */
+#define RCAR_GEN2_PHY_CTL5_TR BIT(2) /* Termination Resistor */
+
+enum sata_rcar_type {
+ RCAR_GEN1_SATA,
+ RCAR_GEN2_SATA,
+};
+
struct sata_rcar_priv {
void __iomem *base;
struct clk *clk;
+ enum sata_rcar_type type;
};
-static void sata_rcar_phy_initialize(struct sata_rcar_priv *priv)
+static void sata_rcar_gen1_phy_preinit(struct sata_rcar_priv *priv)
{
void __iomem *base = priv->base;
@@ -141,8 +167,8 @@ static void sata_rcar_phy_initialize(struct sata_rcar_priv *priv)
iowrite32(0, base + SATAPHYRESET_REG);
}
-static void sata_rcar_phy_write(struct sata_rcar_priv *priv, u16 reg, u32 val,
- int group)
+static void sata_rcar_gen1_phy_write(struct sata_rcar_priv *priv, u16 reg,
+ u32 val, int group)
{
void __iomem *base = priv->base;
int timeout;
@@ -170,6 +196,29 @@ static void sata_rcar_phy_write(struct sata_rcar_priv *priv, u16 reg, u32 val,
iowrite32(0, base + SATAPHYADDR_REG);
}
+static void sata_rcar_gen1_phy_init(struct sata_rcar_priv *priv)
+{
+ sata_rcar_gen1_phy_preinit(priv);
+ sata_rcar_gen1_phy_write(priv, SATAPCTLR1_REG, 0x00200188, 0);
+ sata_rcar_gen1_phy_write(priv, SATAPCTLR1_REG, 0x00200188, 1);
+ sata_rcar_gen1_phy_write(priv, SATAPCTLR3_REG, 0x0000A061, 0);
+ sata_rcar_gen1_phy_write(priv, SATAPCTLR2_REG, 0x20000000, 0);
+ sata_rcar_gen1_phy_write(priv, SATAPCTLR2_REG, 0x20000000, 1);
+ sata_rcar_gen1_phy_write(priv, SATAPCTLR4_REG, 0x28E80000, 0);
+}
+
+static void sata_rcar_gen2_phy_init(struct sata_rcar_priv *priv)
+{
+ void __iomem *base = priv->base;
+
+ iowrite32(RCAR_GEN2_PHY_CTL1, base + RCAR_GEN2_PHY_CTL1_REG);
+ iowrite32(RCAR_GEN2_PHY_CTL2, base + RCAR_GEN2_PHY_CTL2_REG);
+ iowrite32(RCAR_GEN2_PHY_CTL3, base + RCAR_GEN2_PHY_CTL3_REG);
+ iowrite32(RCAR_GEN2_PHY_CTL4, base + RCAR_GEN2_PHY_CTL4_REG);
+ iowrite32(RCAR_GEN2_PHY_CTL5 | RCAR_GEN2_PHY_CTL5_DC |
+ RCAR_GEN2_PHY_CTL5_TR, base + RCAR_GEN2_PHY_CTL5_REG);
+}
+
static void sata_rcar_freeze(struct ata_port *ap)
{
struct sata_rcar_priv *priv = ap->host->private_data;
@@ -738,13 +787,17 @@ static void sata_rcar_init_controller(struct ata_host *host)
u32 val;
/* reset and setup phy */
- sata_rcar_phy_initialize(priv);
- sata_rcar_phy_write(priv, SATAPCTLR1_REG, 0x00200188, 0);
- sata_rcar_phy_write(priv, SATAPCTLR1_REG, 0x00200188, 1);
- sata_rcar_phy_write(priv, SATAPCTLR3_REG, 0x0000A061, 0);
- sata_rcar_phy_write(priv, SATAPCTLR2_REG, 0x20000000, 0);
- sata_rcar_phy_write(priv, SATAPCTLR2_REG, 0x20000000, 1);
- sata_rcar_phy_write(priv, SATAPCTLR4_REG, 0x28E80000, 0);
+ switch (priv->type) {
+ case RCAR_GEN1_SATA:
+ sata_rcar_gen1_phy_init(priv);
+ break;
+ case RCAR_GEN2_SATA:
+ sata_rcar_gen2_phy_init(priv);
+ break;
+ default:
+ dev_warn(host->dev, "SATA phy is not initialized\n");
+ break;
+ }
/* SATA-IP reset state */
val = ioread32(base + ATAPI_CONTROL1_REG);
@@ -770,8 +823,39 @@ static void sata_rcar_init_controller(struct ata_host *host)
iowrite32(ATAPI_INT_ENABLE_SATAINT, base + ATAPI_INT_ENABLE_REG);
}
+static struct of_device_id sata_rcar_match[] = {
+ /* Deprecated, "renesas,sata-r8a7779" should be used instead. */
+ {
+ .compatible = "renesas,rcar-sata",
+ .data = (void *)RCAR_GEN1_SATA,
+ },
+ {
+ .compatible = "renesas,sata-r8a7779",
+ .data = (void *)RCAR_GEN1_SATA,
+ },
+ {
+ .compatible = "renesas,sata-r8a7790",
+ .data = (void *)RCAR_GEN2_SATA
+ },
+ {
+ .compatible = "renesas,sata-r8a7791",
+ .data = (void *)RCAR_GEN2_SATA
+ },
+ {},
+};
+MODULE_DEVICE_TABLE(of, sata_rcar_match);
+
+static const struct platform_device_id sata_rcar_id_table[] = {
+ { "sata-r8a7779", RCAR_GEN1_SATA },
+ { "sata-r8a7790", RCAR_GEN2_SATA },
+ { "sata-r8a7791", RCAR_GEN2_SATA },
+ { },
+};
+MODULE_DEVICE_TABLE(platform, sata_rcar_id_table);
+
static int sata_rcar_probe(struct platform_device *pdev)
{
+ const struct of_device_id *of_id;
struct ata_host *host;
struct sata_rcar_priv *priv;
struct resource *mem;
@@ -787,6 +871,12 @@ static int sata_rcar_probe(struct platform_device *pdev)
if (!priv)
return -ENOMEM;
+ of_id = of_match_device(sata_rcar_match, &pdev->dev);
+ if (of_id)
+ priv->type = (enum sata_rcar_type)of_id->data;
+ else
+ priv->type = platform_get_device_id(pdev)->driver_data;
+
priv->clk = devm_clk_get(&pdev->dev, NULL);
if (IS_ERR(priv->clk)) {
dev_err(&pdev->dev, "failed to get access to sata clock\n");
@@ -892,16 +982,10 @@ static const struct dev_pm_ops sata_rcar_pm_ops = {
};
#endif
-static struct of_device_id sata_rcar_match[] = {
- { .compatible = "renesas,rcar-sata", }, /* Deprecated */
- { .compatible = "renesas,sata-r8a7779", },
- {},
-};
-MODULE_DEVICE_TABLE(of, sata_rcar_match);
-
static struct platform_driver sata_rcar_driver = {
.probe = sata_rcar_probe,
.remove = sata_rcar_remove,
+ .id_table = sata_rcar_id_table,
.driver = {
.name = DRV_NAME,
.owner = THIS_MODULE,
--
1.8.3.1
^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [PATCH 2/2] sata_rcar: Add R-Car Gen2 SATA PHY support
2013-10-16 12:06 ` [PATCH 2/2] sata_rcar: Add R-Car Gen2 SATA PHY support Valentine Barshak
@ 2013-10-29 4:59 ` Simon Horman
2013-10-29 8:24 ` Kumar Gala
2013-10-29 8:46 ` Simon Horman
0 siblings, 2 replies; 12+ messages in thread
From: Simon Horman @ 2013-10-29 4:59 UTC (permalink / raw)
To: Valentine Barshak
Cc: linux-sh, linux-ide, devicetree, Magnus Damm, Vladimir Barinov,
Sergei Shtylyov, Kuninori Morimoto, Laurent Pinchart,
Guennadi Liakhovetski, Tejun Heo, Mark Rutland
On Wed, Oct 16, 2013 at 04:06:01PM +0400, Valentine Barshak wrote:
> R-Car Gen2 SoCs have a different PHY which is not compatible
> with the older R-Car H1 (R8A7779) version.
> This adds OF/platform device id tables and PHY initialization
> callbacks for the following Gen2 SoCs:
> * R-Car H2: R8A7790;
> * R-Car M2: R8A7791.
>
> PHY initialization method is chosen based on the device id.
> Default PHY settings are applied for Gen2 SoCs, which should
> suit the Gen2 boards available.
>
> The R8A7779 platform code is modified to use "sata-r8a7779"
> device name.
>
> Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
> ---
> .../devicetree/bindings/ata/sata_rcar.txt | 5 +-
> arch/arm/mach-shmobile/clock-r8a7779.c | 2 +-
> arch/arm/mach-shmobile/setup-r8a7779.c | 2 +-
> drivers/ata/sata_rcar.c | 118 ++++++++++++++++++---
Hi Mark, Hi Device-Tree Folks,
I'm wondering if you have had a chance to look over the bindings
aspect of this and the other patch in the series. I believe that
this series addresses all previous review in that regards.
Hi Valentine,
I would like to request that the arch/arm/mach-shmobile/ portion
of this patch be split out into a separate patch. The reason is
that in general it is nicer to apply driver changes separately
to platform changes: for starters they have different maintainers.
And in this case there seems to be no reason not to split the change.
Also, I would like to this chance to pass on part of a discussion
at the ARM Linux Kernel summit which is that when posting a series of
patches please only CC devicetree@vger.kernel.org on the patches in
the series that relate to device tree. This would not include
to the new patch with only the arch/arm/mach-shmobile/ portions
of this patch. Feel free to post that patch as a separate series
noting its dependencies below '---' accordingly.
> 4 files changed, 107 insertions(+), 20 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/ata/sata_rcar.txt b/Documentation/devicetree/bindings/ata/sata_rcar.txt
> index 0719115..d6b20a6 100644
> --- a/Documentation/devicetree/bindings/ata/sata_rcar.txt
> +++ b/Documentation/devicetree/bindings/ata/sata_rcar.txt
> @@ -1,7 +1,10 @@
> * Renesas R-Car SATA
>
> Required properties:
> -- compatible : should contain "renesas,sata-r8a7779";
> +- compatible : should contain one of the following:
> + - "renesas,sata-r8a7779" for R-Car H1
> + - "renesas,sata-r8a7790" for R-Car H2
> + - "renesas,sata-r8a7791" for R-Car M2
> - reg : offset and length of the SATA registers;
> - interrupts : must consist of one interrupt specifier.
>
> diff --git a/arch/arm/mach-shmobile/clock-r8a7779.c b/arch/arm/mach-shmobile/clock-r8a7779.c
> index 5c83259..b2f8417 100644
> --- a/arch/arm/mach-shmobile/clock-r8a7779.c
> +++ b/arch/arm/mach-shmobile/clock-r8a7779.c
> @@ -170,7 +170,7 @@ static struct clk_lookup lookups[] = {
> /* MSTP32 clocks */
> CLKDEV_DEV_ID("r8a7779-vin.3", &mstp_clks[MSTP120]), /* VIN3 */
> CLKDEV_DEV_ID("rcar-pcie", &mstp_clks[MSTP116]), /* PCIe */
> - CLKDEV_DEV_ID("sata_rcar", &mstp_clks[MSTP115]), /* SATA */
> + CLKDEV_DEV_ID("sata-r8a7779", &mstp_clks[MSTP115]), /* SATA */
> CLKDEV_DEV_ID("fc600000.sata", &mstp_clks[MSTP115]), /* SATA w/DT */
> CLKDEV_DEV_ID("r8a777x-ether", &mstp_clks[MSTP114]), /* Ether */
> CLKDEV_DEV_ID("r8a7779-vin.0", &mstp_clks[MSTP110]), /* VIN0 */
> diff --git a/arch/arm/mach-shmobile/setup-r8a7779.c b/arch/arm/mach-shmobile/setup-r8a7779.c
> index 51a43c5..9d49090 100644
> --- a/arch/arm/mach-shmobile/setup-r8a7779.c
> +++ b/arch/arm/mach-shmobile/setup-r8a7779.c
> @@ -438,7 +438,7 @@ static struct resource sata_resources[] = {
> };
>
> static struct platform_device sata_device = {
> - .name = "sata_rcar",
> + .name = "sata-r8a7779",
> .id = -1,
> .resource = sata_resources,
> .num_resources = ARRAY_SIZE(sata_resources),
> diff --git a/drivers/ata/sata_rcar.c b/drivers/ata/sata_rcar.c
> index a625cc5..068d5b4 100644
> --- a/drivers/ata/sata_rcar.c
> +++ b/drivers/ata/sata_rcar.c
> @@ -15,6 +15,7 @@
> #include <linux/module.h>
> #include <linux/ata.h>
> #include <linux/libata.h>
> +#include <linux/of_device.h>
> #include <linux/platform_device.h>
> #include <linux/clk.h>
> #include <linux/err.h>
> @@ -123,12 +124,37 @@
>
> #define SATA_RCAR_DMA_BOUNDARY 0x1FFFFFFEUL
>
> +/* Gen2 Physical Layer Control Registers */
> +#define RCAR_GEN2_PHY_CTL1_REG 0x1704
> +#define RCAR_GEN2_PHY_CTL1 0x34180002
> +#define RCAR_GEN2_PHY_CTL1_SS 0xC180 /* Spread Spectrum */
> +
> +#define RCAR_GEN2_PHY_CTL2_REG 0x170C
> +#define RCAR_GEN2_PHY_CTL2 0x00002303
> +
> +#define RCAR_GEN2_PHY_CTL3_REG 0x171C
> +#define RCAR_GEN2_PHY_CTL3 0x000B0194
> +
> +#define RCAR_GEN2_PHY_CTL4_REG 0x1724
> +#define RCAR_GEN2_PHY_CTL4 0x00030994
> +
> +#define RCAR_GEN2_PHY_CTL5_REG 0x1740
> +#define RCAR_GEN2_PHY_CTL5 0x03004001
> +#define RCAR_GEN2_PHY_CTL5_DC BIT(1) /* DC connection */
> +#define RCAR_GEN2_PHY_CTL5_TR BIT(2) /* Termination Resistor */
> +
> +enum sata_rcar_type {
> + RCAR_GEN1_SATA,
> + RCAR_GEN2_SATA,
> +};
> +
> struct sata_rcar_priv {
> void __iomem *base;
> struct clk *clk;
> + enum sata_rcar_type type;
> };
>
> -static void sata_rcar_phy_initialize(struct sata_rcar_priv *priv)
> +static void sata_rcar_gen1_phy_preinit(struct sata_rcar_priv *priv)
> {
> void __iomem *base = priv->base;
>
> @@ -141,8 +167,8 @@ static void sata_rcar_phy_initialize(struct sata_rcar_priv *priv)
> iowrite32(0, base + SATAPHYRESET_REG);
> }
>
> -static void sata_rcar_phy_write(struct sata_rcar_priv *priv, u16 reg, u32 val,
> - int group)
> +static void sata_rcar_gen1_phy_write(struct sata_rcar_priv *priv, u16 reg,
> + u32 val, int group)
> {
> void __iomem *base = priv->base;
> int timeout;
> @@ -170,6 +196,29 @@ static void sata_rcar_phy_write(struct sata_rcar_priv *priv, u16 reg, u32 val,
> iowrite32(0, base + SATAPHYADDR_REG);
> }
>
> +static void sata_rcar_gen1_phy_init(struct sata_rcar_priv *priv)
> +{
> + sata_rcar_gen1_phy_preinit(priv);
> + sata_rcar_gen1_phy_write(priv, SATAPCTLR1_REG, 0x00200188, 0);
> + sata_rcar_gen1_phy_write(priv, SATAPCTLR1_REG, 0x00200188, 1);
> + sata_rcar_gen1_phy_write(priv, SATAPCTLR3_REG, 0x0000A061, 0);
> + sata_rcar_gen1_phy_write(priv, SATAPCTLR2_REG, 0x20000000, 0);
> + sata_rcar_gen1_phy_write(priv, SATAPCTLR2_REG, 0x20000000, 1);
> + sata_rcar_gen1_phy_write(priv, SATAPCTLR4_REG, 0x28E80000, 0);
> +}
> +
> +static void sata_rcar_gen2_phy_init(struct sata_rcar_priv *priv)
> +{
> + void __iomem *base = priv->base;
> +
> + iowrite32(RCAR_GEN2_PHY_CTL1, base + RCAR_GEN2_PHY_CTL1_REG);
> + iowrite32(RCAR_GEN2_PHY_CTL2, base + RCAR_GEN2_PHY_CTL2_REG);
> + iowrite32(RCAR_GEN2_PHY_CTL3, base + RCAR_GEN2_PHY_CTL3_REG);
> + iowrite32(RCAR_GEN2_PHY_CTL4, base + RCAR_GEN2_PHY_CTL4_REG);
> + iowrite32(RCAR_GEN2_PHY_CTL5 | RCAR_GEN2_PHY_CTL5_DC |
> + RCAR_GEN2_PHY_CTL5_TR, base + RCAR_GEN2_PHY_CTL5_REG);
> +}
> +
> static void sata_rcar_freeze(struct ata_port *ap)
> {
> struct sata_rcar_priv *priv = ap->host->private_data;
> @@ -738,13 +787,17 @@ static void sata_rcar_init_controller(struct ata_host *host)
> u32 val;
>
> /* reset and setup phy */
> - sata_rcar_phy_initialize(priv);
> - sata_rcar_phy_write(priv, SATAPCTLR1_REG, 0x00200188, 0);
> - sata_rcar_phy_write(priv, SATAPCTLR1_REG, 0x00200188, 1);
> - sata_rcar_phy_write(priv, SATAPCTLR3_REG, 0x0000A061, 0);
> - sata_rcar_phy_write(priv, SATAPCTLR2_REG, 0x20000000, 0);
> - sata_rcar_phy_write(priv, SATAPCTLR2_REG, 0x20000000, 1);
> - sata_rcar_phy_write(priv, SATAPCTLR4_REG, 0x28E80000, 0);
> + switch (priv->type) {
> + case RCAR_GEN1_SATA:
> + sata_rcar_gen1_phy_init(priv);
> + break;
> + case RCAR_GEN2_SATA:
> + sata_rcar_gen2_phy_init(priv);
> + break;
> + default:
> + dev_warn(host->dev, "SATA phy is not initialized\n");
> + break;
> + }
>
> /* SATA-IP reset state */
> val = ioread32(base + ATAPI_CONTROL1_REG);
> @@ -770,8 +823,39 @@ static void sata_rcar_init_controller(struct ata_host *host)
> iowrite32(ATAPI_INT_ENABLE_SATAINT, base + ATAPI_INT_ENABLE_REG);
> }
>
> +static struct of_device_id sata_rcar_match[] = {
> + /* Deprecated, "renesas,sata-r8a7779" should be used instead. */
> + {
> + .compatible = "renesas,rcar-sata",
> + .data = (void *)RCAR_GEN1_SATA,
> + },
> + {
> + .compatible = "renesas,sata-r8a7779",
> + .data = (void *)RCAR_GEN1_SATA,
> + },
> + {
> + .compatible = "renesas,sata-r8a7790",
> + .data = (void *)RCAR_GEN2_SATA
> + },
> + {
> + .compatible = "renesas,sata-r8a7791",
> + .data = (void *)RCAR_GEN2_SATA
> + },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, sata_rcar_match);
> +
> +static const struct platform_device_id sata_rcar_id_table[] = {
> + { "sata-r8a7779", RCAR_GEN1_SATA },
> + { "sata-r8a7790", RCAR_GEN2_SATA },
> + { "sata-r8a7791", RCAR_GEN2_SATA },
> + { },
> +};
> +MODULE_DEVICE_TABLE(platform, sata_rcar_id_table);
> +
> static int sata_rcar_probe(struct platform_device *pdev)
> {
> + const struct of_device_id *of_id;
> struct ata_host *host;
> struct sata_rcar_priv *priv;
> struct resource *mem;
> @@ -787,6 +871,12 @@ static int sata_rcar_probe(struct platform_device *pdev)
> if (!priv)
> return -ENOMEM;
>
> + of_id = of_match_device(sata_rcar_match, &pdev->dev);
> + if (of_id)
> + priv->type = (enum sata_rcar_type)of_id->data;
> + else
> + priv->type = platform_get_device_id(pdev)->driver_data;
> +
> priv->clk = devm_clk_get(&pdev->dev, NULL);
> if (IS_ERR(priv->clk)) {
> dev_err(&pdev->dev, "failed to get access to sata clock\n");
> @@ -892,16 +982,10 @@ static const struct dev_pm_ops sata_rcar_pm_ops = {
> };
> #endif
>
> -static struct of_device_id sata_rcar_match[] = {
> - { .compatible = "renesas,rcar-sata", }, /* Deprecated */
> - { .compatible = "renesas,sata-r8a7779", },
> - {},
> -};
> -MODULE_DEVICE_TABLE(of, sata_rcar_match);
> -
> static struct platform_driver sata_rcar_driver = {
> .probe = sata_rcar_probe,
> .remove = sata_rcar_remove,
> + .id_table = sata_rcar_id_table,
> .driver = {
> .name = DRV_NAME,
> .owner = THIS_MODULE,
> --
> 1.8.3.1
>
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 2/2] sata_rcar: Add R-Car Gen2 SATA PHY support
2013-10-29 4:59 ` Simon Horman
@ 2013-10-29 8:24 ` Kumar Gala
2013-10-29 8:44 ` Simon Horman
2013-10-29 8:46 ` Simon Horman
1 sibling, 1 reply; 12+ messages in thread
From: Kumar Gala @ 2013-10-29 8:24 UTC (permalink / raw)
To: Simon Horman
Cc: Valentine Barshak, linux-sh, linux-ide, devicetree, Magnus Damm,
Vladimir Barinov, Sergei Shtylyov, Kuninori Morimoto,
Laurent Pinchart, Guennadi Liakhovetski, Tejun Heo, Mark Rutland
On Oct 28, 2013, at 11:59 PM, Simon Horman wrote:
> On Wed, Oct 16, 2013 at 04:06:01PM +0400, Valentine Barshak wrote:
>> R-Car Gen2 SoCs have a different PHY which is not compatible
>> with the older R-Car H1 (R8A7779) version.
>> This adds OF/platform device id tables and PHY initialization
>> callbacks for the following Gen2 SoCs:
>> * R-Car H2: R8A7790;
>> * R-Car M2: R8A7791.
>>
>> PHY initialization method is chosen based on the device id.
>> Default PHY settings are applied for Gen2 SoCs, which should
>> suit the Gen2 boards available.
>>
>> The R8A7779 platform code is modified to use "sata-r8a7779"
>> device name.
>>
>> Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
>> ---
>> .../devicetree/bindings/ata/sata_rcar.txt | 5 +-
>> arch/arm/mach-shmobile/clock-r8a7779.c | 2 +-
>> arch/arm/mach-shmobile/setup-r8a7779.c | 2 +-
>> drivers/ata/sata_rcar.c | 118 ++++++++++++++++++---
>
> Hi Mark, Hi Device-Tree Folks,
>
> I'm wondering if you have had a chance to look over the bindings
> aspect of this and the other patch in the series. I believe that
> this series addresses all previous review in that regards.
What tree is this binding in?
>
> Hi Valentine,
>
> I would like to request that the arch/arm/mach-shmobile/ portion
> of this patch be split out into a separate patch. The reason is
> that in general it is nicer to apply driver changes separately
> to platform changes: for starters they have different maintainers.
> And in this case there seems to be no reason not to split the change.
>
> Also, I would like to this chance to pass on part of a discussion
> at the ARM Linux Kernel summit which is that when posting a series of
> patches please only CC devicetree@vger.kernel.org on the patches in
> the series that relate to device tree. This would not include
> to the new patch with only the arch/arm/mach-shmobile/ portions
> of this patch. Feel free to post that patch as a separate series
> noting its dependencies below '---' accordingly.
>
>> 4 files changed, 107 insertions(+), 20 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/ata/sata_rcar.txt b/Documentation/devicetree/bindings/ata/sata_rcar.txt
>> index 0719115..d6b20a6 100644
>> --- a/Documentation/devicetree/bindings/ata/sata_rcar.txt
>> +++ b/Documentation/devicetree/bindings/ata/sata_rcar.txt
>> @@ -1,7 +1,10 @@
>> * Renesas R-Car SATA
>>
>> Required properties:
>> -- compatible : should contain "renesas,sata-r8a7779";
>> +- compatible : should contain one of the following:
>> + - "renesas,sata-r8a7779" for R-Car H1
>> + - "renesas,sata-r8a7790" for R-Car H2
>> + - "renesas,sata-r8a7791" for R-Car M2
>> - reg : offset and length of the SATA registers;
>> - interrupts : must consist of one interrupt specifier.
We normally have an example (not sure if there is one, and just not seeing it because of diff or not).
- k
--
Employee of Qualcomm Innovation Center, Inc.
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 2/2] sata_rcar: Add R-Car Gen2 SATA PHY support
2013-10-29 8:24 ` Kumar Gala
@ 2013-10-29 8:44 ` Simon Horman
2013-10-29 17:19 ` Kumar Gala
0 siblings, 1 reply; 12+ messages in thread
From: Simon Horman @ 2013-10-29 8:44 UTC (permalink / raw)
To: Kumar Gala
Cc: Valentine Barshak, linux-sh, linux-ide, devicetree, Magnus Damm,
Vladimir Barinov, Sergei Shtylyov, Kuninori Morimoto,
Laurent Pinchart, Guennadi Liakhovetski, Tejun Heo, Mark Rutland
On Tue, Oct 29, 2013 at 03:24:16AM -0500, Kumar Gala wrote:
>
> On Oct 28, 2013, at 11:59 PM, Simon Horman wrote:
>
> > On Wed, Oct 16, 2013 at 04:06:01PM +0400, Valentine Barshak wrote:
> >> R-Car Gen2 SoCs have a different PHY which is not compatible
> >> with the older R-Car H1 (R8A7779) version.
> >> This adds OF/platform device id tables and PHY initialization
> >> callbacks for the following Gen2 SoCs:
> >> * R-Car H2: R8A7790;
> >> * R-Car M2: R8A7791.
> >>
> >> PHY initialization method is chosen based on the device id.
> >> Default PHY settings are applied for Gen2 SoCs, which should
> >> suit the Gen2 boards available.
> >>
> >> The R8A7779 platform code is modified to use "sata-r8a7779"
> >> device name.
> >>
> >> Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
> >> ---
> >> .../devicetree/bindings/ata/sata_rcar.txt | 5 +-
> >> arch/arm/mach-shmobile/clock-r8a7779.c | 2 +-
> >> arch/arm/mach-shmobile/setup-r8a7779.c | 2 +-
> >> drivers/ata/sata_rcar.c | 118 ++++++++++++++++++---
> >
> > Hi Mark, Hi Device-Tree Folks,
> >
> > I'm wondering if you have had a chance to look over the bindings
> > aspect of this and the other patch in the series. I believe that
> > this series addresses all previous review in that regards.
>
> What tree is this binding in?
sata_car.txt is added by the previous patch in this series
"[PATCH 1/2] sata_rcar: Adjust and document device tree bindings"
> > Hi Valentine,
> >
> > I would like to request that the arch/arm/mach-shmobile/ portion
> > of this patch be split out into a separate patch. The reason is
> > that in general it is nicer to apply driver changes separately
> > to platform changes: for starters they have different maintainers.
> > And in this case there seems to be no reason not to split the change.
> >
> > Also, I would like to this chance to pass on part of a discussion
> > at the ARM Linux Kernel summit which is that when posting a series of
> > patches please only CC devicetree@vger.kernel.org on the patches in
> > the series that relate to device tree. This would not include
> > to the new patch with only the arch/arm/mach-shmobile/ portions
> > of this patch. Feel free to post that patch as a separate series
> > noting its dependencies below '---' accordingly.
> >
> >> 4 files changed, 107 insertions(+), 20 deletions(-)
> >>
> >> diff --git a/Documentation/devicetree/bindings/ata/sata_rcar.txt b/Documentation/devicetree/bindings/ata/sata_rcar.txt
> >> index 0719115..d6b20a6 100644
> >> --- a/Documentation/devicetree/bindings/ata/sata_rcar.txt
> >> +++ b/Documentation/devicetree/bindings/ata/sata_rcar.txt
> >> @@ -1,7 +1,10 @@
> >> * Renesas R-Car SATA
> >>
> >> Required properties:
> >> -- compatible : should contain "renesas,sata-r8a7779";
> >> +- compatible : should contain one of the following:
> >> + - "renesas,sata-r8a7779" for R-Car H1
> >> + - "renesas,sata-r8a7790" for R-Car H2
> >> + - "renesas,sata-r8a7791" for R-Car M2
> >> - reg : offset and length of the SATA registers;
> >> - interrupts : must consist of one interrupt specifier.
>
> We normally have an example (not sure if there is one, and just not seeing it because of diff or not).
An example is present.
I have included the text of sata_rcar.txt below to aid review:
---- begin sata_rcar.txt ----
* Renesas R-Car SATA
Required properties:
- compatible : should contain "renesas,sata-r8a7779";
- reg : offset and length of the SATA registers;
- interrupts : must consist of one interrupt specifier.
Example:
sata: sata@fc600000 {
compatible = "renesas,sata-r8a7779";
reg = <0xfc600000 0x2000>;
interrupt-parent = <&gic>;
interrupts = <0 100 0x4>;
};
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 2/2] sata_rcar: Add R-Car Gen2 SATA PHY support
2013-10-29 4:59 ` Simon Horman
2013-10-29 8:24 ` Kumar Gala
@ 2013-10-29 8:46 ` Simon Horman
1 sibling, 0 replies; 12+ messages in thread
From: Simon Horman @ 2013-10-29 8:46 UTC (permalink / raw)
To: Valentine Barshak
Cc: linux-sh, linux-ide, devicetree, Magnus Damm, Vladimir Barinov,
Sergei Shtylyov, Kuninori Morimoto, Laurent Pinchart,
Guennadi Liakhovetski, Tejun Heo, Mark Rutland
On Tue, Oct 29, 2013 at 01:59:43PM +0900, Simon Horman wrote:
> On Wed, Oct 16, 2013 at 04:06:01PM +0400, Valentine Barshak wrote:
> > R-Car Gen2 SoCs have a different PHY which is not compatible
> > with the older R-Car H1 (R8A7779) version.
> > This adds OF/platform device id tables and PHY initialization
> > callbacks for the following Gen2 SoCs:
> > * R-Car H2: R8A7790;
> > * R-Car M2: R8A7791.
> >
> > PHY initialization method is chosen based on the device id.
> > Default PHY settings are applied for Gen2 SoCs, which should
> > suit the Gen2 boards available.
> >
> > The R8A7779 platform code is modified to use "sata-r8a7779"
> > device name.
> >
> > Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
> > ---
> > .../devicetree/bindings/ata/sata_rcar.txt | 5 +-
> > arch/arm/mach-shmobile/clock-r8a7779.c | 2 +-
> > arch/arm/mach-shmobile/setup-r8a7779.c | 2 +-
> > drivers/ata/sata_rcar.c | 118 ++++++++++++++++++---
>
> Hi Mark, Hi Device-Tree Folks,
>
> I'm wondering if you have had a chance to look over the bindings
> aspect of this and the other patch in the series. I believe that
> this series addresses all previous review in that regards.
>
> Hi Valentine,
>
> I would like to request that the arch/arm/mach-shmobile/ portion
> of this patch be split out into a separate patch. The reason is
> that in general it is nicer to apply driver changes separately
> to platform changes: for starters they have different maintainers.
> And in this case there seems to be no reason not to split the change.
I now realise that my assertion is false and in its current
form the changes in this patch need to be done atomically.
I'm unsure what the motivation for this is.
>
> Also, I would like to this chance to pass on part of a discussion
> at the ARM Linux Kernel summit which is that when posting a series of
> patches please only CC devicetree@vger.kernel.org on the patches in
> the series that relate to device tree. This would not include
> to the new patch with only the arch/arm/mach-shmobile/ portions
> of this patch. Feel free to post that patch as a separate series
> noting its dependencies below '---' accordingly.
>
> > 4 files changed, 107 insertions(+), 20 deletions(-)
> >
> > diff --git a/Documentation/devicetree/bindings/ata/sata_rcar.txt b/Documentation/devicetree/bindings/ata/sata_rcar.txt
> > index 0719115..d6b20a6 100644
> > --- a/Documentation/devicetree/bindings/ata/sata_rcar.txt
> > +++ b/Documentation/devicetree/bindings/ata/sata_rcar.txt
> > @@ -1,7 +1,10 @@
> > * Renesas R-Car SATA
> >
> > Required properties:
> > -- compatible : should contain "renesas,sata-r8a7779";
> > +- compatible : should contain one of the following:
> > + - "renesas,sata-r8a7779" for R-Car H1
> > + - "renesas,sata-r8a7790" for R-Car H2
> > + - "renesas,sata-r8a7791" for R-Car M2
> > - reg : offset and length of the SATA registers;
> > - interrupts : must consist of one interrupt specifier.
> >
> > diff --git a/arch/arm/mach-shmobile/clock-r8a7779.c b/arch/arm/mach-shmobile/clock-r8a7779.c
> > index 5c83259..b2f8417 100644
> > --- a/arch/arm/mach-shmobile/clock-r8a7779.c
> > +++ b/arch/arm/mach-shmobile/clock-r8a7779.c
> > @@ -170,7 +170,7 @@ static struct clk_lookup lookups[] = {
> > /* MSTP32 clocks */
> > CLKDEV_DEV_ID("r8a7779-vin.3", &mstp_clks[MSTP120]), /* VIN3 */
> > CLKDEV_DEV_ID("rcar-pcie", &mstp_clks[MSTP116]), /* PCIe */
> > - CLKDEV_DEV_ID("sata_rcar", &mstp_clks[MSTP115]), /* SATA */
> > + CLKDEV_DEV_ID("sata-r8a7779", &mstp_clks[MSTP115]), /* SATA */
> > CLKDEV_DEV_ID("fc600000.sata", &mstp_clks[MSTP115]), /* SATA w/DT */
> > CLKDEV_DEV_ID("r8a777x-ether", &mstp_clks[MSTP114]), /* Ether */
> > CLKDEV_DEV_ID("r8a7779-vin.0", &mstp_clks[MSTP110]), /* VIN0 */
> > diff --git a/arch/arm/mach-shmobile/setup-r8a7779.c b/arch/arm/mach-shmobile/setup-r8a7779.c
> > index 51a43c5..9d49090 100644
> > --- a/arch/arm/mach-shmobile/setup-r8a7779.c
> > +++ b/arch/arm/mach-shmobile/setup-r8a7779.c
> > @@ -438,7 +438,7 @@ static struct resource sata_resources[] = {
> > };
> >
> > static struct platform_device sata_device = {
> > - .name = "sata_rcar",
> > + .name = "sata-r8a7779",
> > .id = -1,
> > .resource = sata_resources,
> > .num_resources = ARRAY_SIZE(sata_resources),
> > diff --git a/drivers/ata/sata_rcar.c b/drivers/ata/sata_rcar.c
> > index a625cc5..068d5b4 100644
> > --- a/drivers/ata/sata_rcar.c
> > +++ b/drivers/ata/sata_rcar.c
> > @@ -15,6 +15,7 @@
> > #include <linux/module.h>
> > #include <linux/ata.h>
> > #include <linux/libata.h>
> > +#include <linux/of_device.h>
> > #include <linux/platform_device.h>
> > #include <linux/clk.h>
> > #include <linux/err.h>
> > @@ -123,12 +124,37 @@
> >
> > #define SATA_RCAR_DMA_BOUNDARY 0x1FFFFFFEUL
> >
> > +/* Gen2 Physical Layer Control Registers */
> > +#define RCAR_GEN2_PHY_CTL1_REG 0x1704
> > +#define RCAR_GEN2_PHY_CTL1 0x34180002
> > +#define RCAR_GEN2_PHY_CTL1_SS 0xC180 /* Spread Spectrum */
> > +
> > +#define RCAR_GEN2_PHY_CTL2_REG 0x170C
> > +#define RCAR_GEN2_PHY_CTL2 0x00002303
> > +
> > +#define RCAR_GEN2_PHY_CTL3_REG 0x171C
> > +#define RCAR_GEN2_PHY_CTL3 0x000B0194
> > +
> > +#define RCAR_GEN2_PHY_CTL4_REG 0x1724
> > +#define RCAR_GEN2_PHY_CTL4 0x00030994
> > +
> > +#define RCAR_GEN2_PHY_CTL5_REG 0x1740
> > +#define RCAR_GEN2_PHY_CTL5 0x03004001
> > +#define RCAR_GEN2_PHY_CTL5_DC BIT(1) /* DC connection */
> > +#define RCAR_GEN2_PHY_CTL5_TR BIT(2) /* Termination Resistor */
> > +
> > +enum sata_rcar_type {
> > + RCAR_GEN1_SATA,
> > + RCAR_GEN2_SATA,
> > +};
> > +
> > struct sata_rcar_priv {
> > void __iomem *base;
> > struct clk *clk;
> > + enum sata_rcar_type type;
> > };
> >
> > -static void sata_rcar_phy_initialize(struct sata_rcar_priv *priv)
> > +static void sata_rcar_gen1_phy_preinit(struct sata_rcar_priv *priv)
> > {
> > void __iomem *base = priv->base;
> >
> > @@ -141,8 +167,8 @@ static void sata_rcar_phy_initialize(struct sata_rcar_priv *priv)
> > iowrite32(0, base + SATAPHYRESET_REG);
> > }
> >
> > -static void sata_rcar_phy_write(struct sata_rcar_priv *priv, u16 reg, u32 val,
> > - int group)
> > +static void sata_rcar_gen1_phy_write(struct sata_rcar_priv *priv, u16 reg,
> > + u32 val, int group)
> > {
> > void __iomem *base = priv->base;
> > int timeout;
> > @@ -170,6 +196,29 @@ static void sata_rcar_phy_write(struct sata_rcar_priv *priv, u16 reg, u32 val,
> > iowrite32(0, base + SATAPHYADDR_REG);
> > }
> >
> > +static void sata_rcar_gen1_phy_init(struct sata_rcar_priv *priv)
> > +{
> > + sata_rcar_gen1_phy_preinit(priv);
> > + sata_rcar_gen1_phy_write(priv, SATAPCTLR1_REG, 0x00200188, 0);
> > + sata_rcar_gen1_phy_write(priv, SATAPCTLR1_REG, 0x00200188, 1);
> > + sata_rcar_gen1_phy_write(priv, SATAPCTLR3_REG, 0x0000A061, 0);
> > + sata_rcar_gen1_phy_write(priv, SATAPCTLR2_REG, 0x20000000, 0);
> > + sata_rcar_gen1_phy_write(priv, SATAPCTLR2_REG, 0x20000000, 1);
> > + sata_rcar_gen1_phy_write(priv, SATAPCTLR4_REG, 0x28E80000, 0);
> > +}
> > +
> > +static void sata_rcar_gen2_phy_init(struct sata_rcar_priv *priv)
> > +{
> > + void __iomem *base = priv->base;
> > +
> > + iowrite32(RCAR_GEN2_PHY_CTL1, base + RCAR_GEN2_PHY_CTL1_REG);
> > + iowrite32(RCAR_GEN2_PHY_CTL2, base + RCAR_GEN2_PHY_CTL2_REG);
> > + iowrite32(RCAR_GEN2_PHY_CTL3, base + RCAR_GEN2_PHY_CTL3_REG);
> > + iowrite32(RCAR_GEN2_PHY_CTL4, base + RCAR_GEN2_PHY_CTL4_REG);
> > + iowrite32(RCAR_GEN2_PHY_CTL5 | RCAR_GEN2_PHY_CTL5_DC |
> > + RCAR_GEN2_PHY_CTL5_TR, base + RCAR_GEN2_PHY_CTL5_REG);
> > +}
> > +
> > static void sata_rcar_freeze(struct ata_port *ap)
> > {
> > struct sata_rcar_priv *priv = ap->host->private_data;
> > @@ -738,13 +787,17 @@ static void sata_rcar_init_controller(struct ata_host *host)
> > u32 val;
> >
> > /* reset and setup phy */
> > - sata_rcar_phy_initialize(priv);
> > - sata_rcar_phy_write(priv, SATAPCTLR1_REG, 0x00200188, 0);
> > - sata_rcar_phy_write(priv, SATAPCTLR1_REG, 0x00200188, 1);
> > - sata_rcar_phy_write(priv, SATAPCTLR3_REG, 0x0000A061, 0);
> > - sata_rcar_phy_write(priv, SATAPCTLR2_REG, 0x20000000, 0);
> > - sata_rcar_phy_write(priv, SATAPCTLR2_REG, 0x20000000, 1);
> > - sata_rcar_phy_write(priv, SATAPCTLR4_REG, 0x28E80000, 0);
> > + switch (priv->type) {
> > + case RCAR_GEN1_SATA:
> > + sata_rcar_gen1_phy_init(priv);
> > + break;
> > + case RCAR_GEN2_SATA:
> > + sata_rcar_gen2_phy_init(priv);
> > + break;
> > + default:
> > + dev_warn(host->dev, "SATA phy is not initialized\n");
> > + break;
> > + }
> >
> > /* SATA-IP reset state */
> > val = ioread32(base + ATAPI_CONTROL1_REG);
> > @@ -770,8 +823,39 @@ static void sata_rcar_init_controller(struct ata_host *host)
> > iowrite32(ATAPI_INT_ENABLE_SATAINT, base + ATAPI_INT_ENABLE_REG);
> > }
> >
> > +static struct of_device_id sata_rcar_match[] = {
> > + /* Deprecated, "renesas,sata-r8a7779" should be used instead. */
> > + {
> > + .compatible = "renesas,rcar-sata",
> > + .data = (void *)RCAR_GEN1_SATA,
> > + },
> > + {
> > + .compatible = "renesas,sata-r8a7779",
> > + .data = (void *)RCAR_GEN1_SATA,
> > + },
> > + {
> > + .compatible = "renesas,sata-r8a7790",
> > + .data = (void *)RCAR_GEN2_SATA
> > + },
> > + {
> > + .compatible = "renesas,sata-r8a7791",
> > + .data = (void *)RCAR_GEN2_SATA
> > + },
> > + {},
> > +};
> > +MODULE_DEVICE_TABLE(of, sata_rcar_match);
> > +
> > +static const struct platform_device_id sata_rcar_id_table[] = {
> > + { "sata-r8a7779", RCAR_GEN1_SATA },
> > + { "sata-r8a7790", RCAR_GEN2_SATA },
> > + { "sata-r8a7791", RCAR_GEN2_SATA },
> > + { },
> > +};
> > +MODULE_DEVICE_TABLE(platform, sata_rcar_id_table);
> > +
> > static int sata_rcar_probe(struct platform_device *pdev)
> > {
> > + const struct of_device_id *of_id;
> > struct ata_host *host;
> > struct sata_rcar_priv *priv;
> > struct resource *mem;
> > @@ -787,6 +871,12 @@ static int sata_rcar_probe(struct platform_device *pdev)
> > if (!priv)
> > return -ENOMEM;
> >
> > + of_id = of_match_device(sata_rcar_match, &pdev->dev);
> > + if (of_id)
> > + priv->type = (enum sata_rcar_type)of_id->data;
> > + else
> > + priv->type = platform_get_device_id(pdev)->driver_data;
> > +
> > priv->clk = devm_clk_get(&pdev->dev, NULL);
> > if (IS_ERR(priv->clk)) {
> > dev_err(&pdev->dev, "failed to get access to sata clock\n");
> > @@ -892,16 +982,10 @@ static const struct dev_pm_ops sata_rcar_pm_ops = {
> > };
> > #endif
> >
> > -static struct of_device_id sata_rcar_match[] = {
> > - { .compatible = "renesas,rcar-sata", }, /* Deprecated */
> > - { .compatible = "renesas,sata-r8a7779", },
> > - {},
> > -};
> > -MODULE_DEVICE_TABLE(of, sata_rcar_match);
> > -
> > static struct platform_driver sata_rcar_driver = {
> > .probe = sata_rcar_probe,
> > .remove = sata_rcar_remove,
> > + .id_table = sata_rcar_id_table,
> > .driver = {
> > .name = DRV_NAME,
> > .owner = THIS_MODULE,
> > --
> > 1.8.3.1
> >
> --
> To unsubscribe from this list: send the line "unsubscribe linux-sh" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 2/2] sata_rcar: Add R-Car Gen2 SATA PHY support
2013-10-29 8:44 ` Simon Horman
@ 2013-10-29 17:19 ` Kumar Gala
2013-10-30 0:28 ` Simon Horman
0 siblings, 1 reply; 12+ messages in thread
From: Kumar Gala @ 2013-10-29 17:19 UTC (permalink / raw)
To: Simon Horman
Cc: Valentine Barshak, linux-sh, linux-ide, devicetree, Magnus Damm,
Vladimir Barinov, Sergei Shtylyov, Kuninori Morimoto,
Laurent Pinchart, Guennadi Liakhovetski, Tejun Heo, Mark Rutland
On Oct 29, 2013, at 3:44 AM, Simon Horman wrote:
> On Tue, Oct 29, 2013 at 03:24:16AM -0500, Kumar Gala wrote:
>>
>> On Oct 28, 2013, at 11:59 PM, Simon Horman wrote:
>>
>>> On Wed, Oct 16, 2013 at 04:06:01PM +0400, Valentine Barshak wrote:
>>>> R-Car Gen2 SoCs have a different PHY which is not compatible
>>>> with the older R-Car H1 (R8A7779) version.
>>>> This adds OF/platform device id tables and PHY initialization
>>>> callbacks for the following Gen2 SoCs:
>>>> * R-Car H2: R8A7790;
>>>> * R-Car M2: R8A7791.
>>>>
>>>> PHY initialization method is chosen based on the device id.
>>>> Default PHY settings are applied for Gen2 SoCs, which should
>>>> suit the Gen2 boards available.
>>>>
>>>> The R8A7779 platform code is modified to use "sata-r8a7779"
>>>> device name.
>>>>
>>>> Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
>>>> ---
>>>> .../devicetree/bindings/ata/sata_rcar.txt | 5 +-
>>>> arch/arm/mach-shmobile/clock-r8a7779.c | 2 +-
>>>> arch/arm/mach-shmobile/setup-r8a7779.c | 2 +-
>>>> drivers/ata/sata_rcar.c | 118 ++++++++++++++++++---
>>>
>>> Hi Mark, Hi Device-Tree Folks,
>>>
>>> I'm wondering if you have had a chance to look over the bindings
>>> aspect of this and the other patch in the series. I believe that
>>> this series addresses all previous review in that regards.
>>
>> What tree is this binding in?
>
> sata_car.txt is added by the previous patch in this series
> "[PATCH 1/2] sata_rcar: Adjust and document device tree bindings"
Why not just have all the binding in one patch. There isn't a reason this should be split.
- k
--
Employee of Qualcomm Innovation Center, Inc.
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 2/2] sata_rcar: Add R-Car Gen2 SATA PHY support
2013-10-29 17:19 ` Kumar Gala
@ 2013-10-30 0:28 ` Simon Horman
2013-10-30 7:05 ` Kumar Gala
0 siblings, 1 reply; 12+ messages in thread
From: Simon Horman @ 2013-10-30 0:28 UTC (permalink / raw)
To: Kumar Gala
Cc: Valentine Barshak, linux-sh, linux-ide, devicetree, Magnus Damm,
Vladimir Barinov, Sergei Shtylyov, Kuninori Morimoto,
Laurent Pinchart, Guennadi Liakhovetski, Tejun Heo, Mark Rutland
On Tue, Oct 29, 2013 at 12:19:08PM -0500, Kumar Gala wrote:
>
> On Oct 29, 2013, at 3:44 AM, Simon Horman wrote:
>
> > On Tue, Oct 29, 2013 at 03:24:16AM -0500, Kumar Gala wrote:
> >>
> >> On Oct 28, 2013, at 11:59 PM, Simon Horman wrote:
> >>
> >>> On Wed, Oct 16, 2013 at 04:06:01PM +0400, Valentine Barshak wrote:
> >>>> R-Car Gen2 SoCs have a different PHY which is not compatible
> >>>> with the older R-Car H1 (R8A7779) version.
> >>>> This adds OF/platform device id tables and PHY initialization
> >>>> callbacks for the following Gen2 SoCs:
> >>>> * R-Car H2: R8A7790;
> >>>> * R-Car M2: R8A7791.
> >>>>
> >>>> PHY initialization method is chosen based on the device id.
> >>>> Default PHY settings are applied for Gen2 SoCs, which should
> >>>> suit the Gen2 boards available.
> >>>>
> >>>> The R8A7779 platform code is modified to use "sata-r8a7779"
> >>>> device name.
> >>>>
> >>>> Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
> >>>> ---
> >>>> .../devicetree/bindings/ata/sata_rcar.txt | 5 +-
> >>>> arch/arm/mach-shmobile/clock-r8a7779.c | 2 +-
> >>>> arch/arm/mach-shmobile/setup-r8a7779.c | 2 +-
> >>>> drivers/ata/sata_rcar.c | 118 ++++++++++++++++++---
> >>>
> >>> Hi Mark, Hi Device-Tree Folks,
> >>>
> >>> I'm wondering if you have had a chance to look over the bindings
> >>> aspect of this and the other patch in the series. I believe that
> >>> this series addresses all previous review in that regards.
> >>
> >> What tree is this binding in?
> >
> > sata_car.txt is added by the previous patch in this series
> > "[PATCH 1/2] sata_rcar: Adjust and document device tree bindings"
>
> Why not just have all the binding in one patch. There isn't a reason this should be split.
I think that the motivation was that the first patch documents the
existing implementation while the second documents a change to it.
With that in mind would you still like a single patch for the binding?
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 2/2] sata_rcar: Add R-Car Gen2 SATA PHY support
2013-10-30 0:28 ` Simon Horman
@ 2013-10-30 7:05 ` Kumar Gala
2013-10-30 17:07 ` Valentine
0 siblings, 1 reply; 12+ messages in thread
From: Kumar Gala @ 2013-10-30 7:05 UTC (permalink / raw)
To: Simon Horman
Cc: Valentine Barshak, linux-sh, linux-ide, devicetree, Magnus Damm,
Vladimir Barinov, Sergei Shtylyov, Kuninori Morimoto,
Laurent Pinchart, Guennadi Liakhovetski, Tejun Heo, Mark Rutland
On Oct 29, 2013, at 7:28 PM, Simon Horman wrote:
> On Tue, Oct 29, 2013 at 12:19:08PM -0500, Kumar Gala wrote:
>>
>> On Oct 29, 2013, at 3:44 AM, Simon Horman wrote:
>>
>>> On Tue, Oct 29, 2013 at 03:24:16AM -0500, Kumar Gala wrote:
>>>>
>>>> On Oct 28, 2013, at 11:59 PM, Simon Horman wrote:
>>>>
>>>>> On Wed, Oct 16, 2013 at 04:06:01PM +0400, Valentine Barshak wrote:
>>>>>> R-Car Gen2 SoCs have a different PHY which is not compatible
>>>>>> with the older R-Car H1 (R8A7779) version.
>>>>>> This adds OF/platform device id tables and PHY initialization
>>>>>> callbacks for the following Gen2 SoCs:
>>>>>> * R-Car H2: R8A7790;
>>>>>> * R-Car M2: R8A7791.
>>>>>>
>>>>>> PHY initialization method is chosen based on the device id.
>>>>>> Default PHY settings are applied for Gen2 SoCs, which should
>>>>>> suit the Gen2 boards available.
>>>>>>
>>>>>> The R8A7779 platform code is modified to use "sata-r8a7779"
>>>>>> device name.
>>>>>>
>>>>>> Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
>>>>>> ---
>>>>>> .../devicetree/bindings/ata/sata_rcar.txt | 5 +-
>>>>>> arch/arm/mach-shmobile/clock-r8a7779.c | 2 +-
>>>>>> arch/arm/mach-shmobile/setup-r8a7779.c | 2 +-
>>>>>> drivers/ata/sata_rcar.c | 118 ++++++++++++++++++---
>>>>>
>>>>> Hi Mark, Hi Device-Tree Folks,
>>>>>
>>>>> I'm wondering if you have had a chance to look over the bindings
>>>>> aspect of this and the other patch in the series. I believe that
>>>>> this series addresses all previous review in that regards.
>>>>
>>>> What tree is this binding in?
>>>
>>> sata_car.txt is added by the previous patch in this series
>>> "[PATCH 1/2] sata_rcar: Adjust and document device tree bindings"
>>
>> Why not just have all the binding in one patch. There isn't a reason this should be split.
>
> I think that the motivation was that the first patch documents the
> existing implementation while the second documents a change to it.
> With that in mind would you still like a single patch for the binding?
Yes, I see no reason to split this up as you know both right now.
- k
--
Employee of Qualcomm Innovation Center, Inc.
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH 2/2] sata_rcar: Add R-Car Gen2 SATA PHY support
2013-10-30 7:05 ` Kumar Gala
@ 2013-10-30 17:07 ` Valentine
0 siblings, 0 replies; 12+ messages in thread
From: Valentine @ 2013-10-30 17:07 UTC (permalink / raw)
To: Kumar Gala, Simon Horman
Cc: linux-sh, linux-ide, devicetree, Magnus Damm, Vladimir Barinov,
Sergei Shtylyov, Kuninori Morimoto, Laurent Pinchart,
Guennadi Liakhovetski, Tejun Heo, Mark Rutland
On 10/30/2013 11:05 AM, Kumar Gala wrote:
>
> On Oct 29, 2013, at 7:28 PM, Simon Horman wrote:
>
>> On Tue, Oct 29, 2013 at 12:19:08PM -0500, Kumar Gala wrote:
>>>
>>> On Oct 29, 2013, at 3:44 AM, Simon Horman wrote:
>>>
>>>> On Tue, Oct 29, 2013 at 03:24:16AM -0500, Kumar Gala wrote:
>>>>>
>>>>> On Oct 28, 2013, at 11:59 PM, Simon Horman wrote:
>>>>>
>>>>>> On Wed, Oct 16, 2013 at 04:06:01PM +0400, Valentine Barshak wrote:
>>>>>>> R-Car Gen2 SoCs have a different PHY which is not compatible
>>>>>>> with the older R-Car H1 (R8A7779) version.
>>>>>>> This adds OF/platform device id tables and PHY initialization
>>>>>>> callbacks for the following Gen2 SoCs:
>>>>>>> * R-Car H2: R8A7790;
>>>>>>> * R-Car M2: R8A7791.
>>>>>>>
>>>>>>> PHY initialization method is chosen based on the device id.
>>>>>>> Default PHY settings are applied for Gen2 SoCs, which should
>>>>>>> suit the Gen2 boards available.
>>>>>>>
>>>>>>> The R8A7779 platform code is modified to use "sata-r8a7779"
>>>>>>> device name.
>>>>>>>
>>>>>>> Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
>>>>>>> ---
>>>>>>> .../devicetree/bindings/ata/sata_rcar.txt | 5 +-
>>>>>>> arch/arm/mach-shmobile/clock-r8a7779.c | 2 +-
>>>>>>> arch/arm/mach-shmobile/setup-r8a7779.c | 2 +-
>>>>>>> drivers/ata/sata_rcar.c | 118 ++++++++++++++++++---
>>>>>>
>>>>>> Hi Mark, Hi Device-Tree Folks,
>>>>>>
>>>>>> I'm wondering if you have had a chance to look over the bindings
>>>>>> aspect of this and the other patch in the series. I believe that
>>>>>> this series addresses all previous review in that regards.
>>>>>
>>>>> What tree is this binding in?
>>>>
>>>> sata_car.txt is added by the previous patch in this series
>>>> "[PATCH 1/2] sata_rcar: Adjust and document device tree bindings"
>>>
>>> Why not just have all the binding in one patch. There isn't a reason this should be split.
>>
>> I think that the motivation was that the first patch documents the
>> existing implementation while the second documents a change to it.
>> With that in mind would you still like a single patch for the binding?
>
> Yes, I see no reason to split this up as you know both right now.
>
> - k
>
I'll resend the sata_rcar part as a separate patch in a bit.
I'll keep the old-style compatibility string and device id table entry
for compatibility with existing Marzen (r8a7779) platform code/dts.
Once it is accepted, the bindings documentation will be sent as a separate patch.
Thanks.
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2013-10-30 17:07 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2013-10-16 12:05 [PATCH 0/2] sata_rcar: Adjust DT bindings and add R-Car Gen2 PHY support (take 3) Valentine Barshak
2013-10-16 12:06 ` [PATCH 1/2] sata_rcar: Adjust and document device tree bindings Valentine Barshak
2013-10-16 12:06 ` [PATCH 2/2] sata_rcar: Add R-Car Gen2 SATA PHY support Valentine Barshak
2013-10-29 4:59 ` Simon Horman
2013-10-29 8:24 ` Kumar Gala
2013-10-29 8:44 ` Simon Horman
2013-10-29 17:19 ` Kumar Gala
2013-10-30 0:28 ` Simon Horman
2013-10-30 7:05 ` Kumar Gala
2013-10-30 17:07 ` Valentine
2013-10-29 8:46 ` Simon Horman
-- strict thread matches above, loose matches on Subject: below --
2013-10-15 10:20 [PATCH 0/2] sata_rcar: Adjust DT bindings and add R-Car Gen2 PHY support (take 2) Valentine Barshak
2013-10-15 10:20 ` [PATCH 2/2] sata_rcar: Add R-Car Gen2 SATA PHY support Valentine Barshak
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).