Re: [PATCH v2 4/4] brcmfmac: Fix OOB interrupt not working for BCM43362

[Arend van Spriel <arend-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>]

On 16-06-14 19:56, Hans de Goede wrote:
> It has taken me a long long time to get the OOB interrupt working on the
> AP6210 sdio wifi/bt module found on various Allwinner A20 boards. In the
> end I found these magic register pokes in the cubietruck kernel tree:
> https://github.com/cubieboard2/linux-sunxi/commit/7f08ba395617d17e7a711507503d89a50406fe7a
>
> I'm not entirely sure if this specific to the AP6210 module, or if this
> should be done for all BCM43362 sdio devices.

Hi Hans,

I was still not sure about this one so I asked around. Apart from the 
nvram settings I emailed earlier one more is needed:

sd_gpout=1
sd_oobonly=1
sd_gpval=1
*muxenab=0x11*

Could you give that a try?

Regards,
Arend

> Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
> ---
>   drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c | 16 ++++++++++++++++
>   1 file changed, 16 insertions(+)
>
> diff --git a/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c b/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c
> index 0fc707c..58e86a5 100644
> --- a/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c
> +++ b/drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c
> @@ -39,7 +39,9 @@
>   #include <brcm_hw_ids.h>
>   #include <brcmu_utils.h>
>   #include <brcmu_wifi.h>
> +#include <chipcommon.h>
>   #include <soc.h>
> +#include "chip.h"
>   #include "dhd_bus.h"
>   #include "dhd_dbg.h"
>   #include "sdio_host.h"
> @@ -119,6 +121,7 @@ int brcmf_sdiod_intr_register(struct brcmf_sdio_dev *sdiodev)
>   {
>   	int ret = 0;
>   	u8 data;
> +	u32 addr, gpiocontrol;
>   	unsigned long flags;
>
>   	if ((sdiodev->pdata) && (sdiodev->pdata->oob_irq_supported)) {
> @@ -148,6 +151,19 @@ int brcmf_sdiod_intr_register(struct brcmf_sdio_dev *sdiodev)
>
>   		sdio_claim_host(sdiodev->func[1]);
>
> +		if (sdiodev->bus_if->chip == BCM43362_CHIP_ID) {
> +			/* assign GPIO to SDIO core */
> +			addr = CORE_CC_REG(SI_ENUM_BASE, gpiocontrol);
> +			gpiocontrol = brcmf_sdiod_regrl(sdiodev, addr, &ret);
> +			gpiocontrol |= 0x2;
> +			brcmf_sdiod_regwl(sdiodev, addr, gpiocontrol, &ret);
> +
> +			brcmf_sdiod_regwb(sdiodev, SBSDIO_GPIO_SELECT, 0xf,
> +					  &ret);
> +			brcmf_sdiod_regwb(sdiodev, SBSDIO_GPIO_OUT, 0, &ret);
> +			brcmf_sdiod_regwb(sdiodev, SBSDIO_GPIO_EN, 0x2, &ret);
> +		}
> +
>   		/* must configure SDIO_CCCR_IENx to enable irq */
>   		data = brcmf_sdiod_regrb(sdiodev, SDIO_CCCR_IENx, &ret);
>   		data |= 1 << SDIO_FUNC_1 | 1 << SDIO_FUNC_2 | 1;
>