* [PATCH v5 1/5] dt-bindings: Add RK808 device tree bindings document
@ 2014-08-25 13:29 Chris Zhong
2014-08-25 20:14 ` Doug Anderson
2014-08-26 9:42 ` Mark Rutland
0 siblings, 2 replies; 4+ messages in thread
From: Chris Zhong @ 2014-08-25 13:29 UTC (permalink / raw)
To: robh+dt, pawel.moll, mark.rutland, ijc+devicetree, galak, sameo,
lee.jones, lgirdwood, broonie, a.zummo, mturquette
Cc: devicetree, linux-kernel, rtc-linux, grant.likely, hl, huangtao,
cf, zhangqing, xxx, dianders, heiko, olof, sonnyrao, dtor,
javier.martinez, kever.yang, Chris Zhong
Add device tree bindings documentation and a header file
for rockchip's RK808 pmic.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
---
Changes in v5:
Adviced by doug
- add some error checking in probe
- move "rockchip,rk808.h" into the patch about dt-bindings
Changes in v4:
Adviced by doug
- add "clock-output-names" propertiey
- add a header file "rockchip,rk808.h"
Changes in v3:
- fix compile err
Changes in v2:
Adviced by javier.martinez
- separated from rtc-rk808.c
Documentation/devicetree/bindings/mfd/rk808.txt | 142 +++++++++++++++++++++++
include/dt-bindings/clock/rockchip,rk808.h | 11 ++
2 files changed, 153 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/rk808.txt
create mode 100644 include/dt-bindings/clock/rockchip,rk808.h
diff --git a/Documentation/devicetree/bindings/mfd/rk808.txt b/Documentation/devicetree/bindings/mfd/rk808.txt
new file mode 100644
index 0000000..e5786e9
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/rk808.txt
@@ -0,0 +1,142 @@
+RK808 Power Management Integrated Circuit
+
+Required properties:
+- compatible: "rockchip,rk808"
+- reg: I2C slave address
+- interrupt-parent: The parent interrupt controller.
+- interrupts: the interrupt outputs of the controller.
+- pinctrl-names: Should contain only one value - "default".
+- pinctrl-0: Should specify pin control groups used for this controller.
+- regulators: This is the list of child nodes that specify the regulator
+ initialization data for defined regulators. Not all regulators for the given
+ device need to be present. The definition for each of these nodes is defined
+ using the standard binding for regulators found at
+ Documentation/devicetree/bindings/regulator/regulator.txt.
+- #clock-cells: the value should be 1
+- The following are the names of the regulators that the rk808 pmic block
+ supports. Note: The 'n' below represents the number as per the datasheet:
+
+ - DCDC_REGn
+ - valid values for n are 1 to 4.
+ - LDO_REGn
+ - valid values for n are 1 to 8.
+ - SWITCH_REGn
+ - valid values for n are 1 to 2.
+
+Optional properties:
+- clock-output-names : From common clock binding to override the
+ default output clock name
+- rockchip,system-power-controller: Telling whether or not this pmic is controlling
+ the system power.
+
+Example:
+rk808: pmic@1b {
+ compatible = "rockchip,rk808";
+ interrupt-parent = <&gpio0>;
+ interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int>;
+ reg = <0x1b>;
+ #clock-cells = <1>;
+ clock-output-names = "xin32k0", "xin32k1";
+ rockchip,system-power-controller;
+
+ regulators {
+ rk808_dcdc1_reg: DCDC_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vdd_arm";
+ };
+
+ rk808_dcdc2_reg: DCDC_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-name = "vdd_gpu";
+ };
+
+ rk808_dcdc3_reg: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vdd_ddr";
+ };
+
+ rk808_dcdc4_reg: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio";
+ };
+
+ rk808_ldo1_reg: LDO_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ rk808_ldo2_reg: LDO_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ rk808_ldo3_reg: LDO_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-name = "LDO_REG3";
+ };
+
+ rk808_ldo4_reg: LDO_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ rk808_ldo5_reg: LDO_REG5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ rk808_ldo6_reg: LDO_REG6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+
+ rk808_ldo7_reg: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ rk808_ldo8_reg: LDO_REG8 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ rk808_switch1_reg: SWITCH_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ rk808_switch2_reg: SWITCH_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
+ };
diff --git a/include/dt-bindings/clock/rockchip,rk808.h b/include/dt-bindings/clock/rockchip,rk808.h
new file mode 100644
index 0000000..1a87343
--- /dev/null
+++ b/include/dt-bindings/clock/rockchip,rk808.h
@@ -0,0 +1,11 @@
+/*
+ * This header provides constants clk index RK808 pmic clkout
+ */
+#ifndef _CLK_ROCKCHIP_RK808
+#define _CLK_ROCKCHIP_RK808
+
+/* CLOCKOUT index */
+#define RK808_CLKOUT0 0
+#define RK808_CLKOUT1 1
+
+#endif
--
1.7.9.5
^ permalink raw reply related [flat|nested] 4+ messages in thread* Re: [PATCH v5 1/5] dt-bindings: Add RK808 device tree bindings document
2014-08-25 13:29 [PATCH v5 1/5] dt-bindings: Add RK808 device tree bindings document Chris Zhong
@ 2014-08-25 20:14 ` Doug Anderson
[not found] ` <CAD=FV=Wp7e__00WAcXZB-kZZ28hsnWwq+eYOYeeDMYNQVSmkzA-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2014-08-26 9:42 ` Mark Rutland
1 sibling, 1 reply; 4+ messages in thread
From: Doug Anderson @ 2014-08-25 20:14 UTC (permalink / raw)
To: Chris Zhong
Cc: Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala,
Samuel Ortiz, Lee Jones, Liam Girdwood, broonie@kernel.org,
Alessandro Zummo, Mike Turquette, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, rtc-linux, Grant Likely, Lin Huang,
Tao Huang, Eddie Cai, zhangqing, xxx, Heiko Stübner,
Olof Johansson, Sonny Rao
Chris,
On Mon, Aug 25, 2014 at 6:29 AM, Chris Zhong <zyw@rock-chips.com> wrote:
> Add device tree bindings documentation and a header file
> for rockchip's RK808 pmic.
>
> Signed-off-by: Chris Zhong <zyw@rock-chips.com>
>
> ---
>
> Changes in v5:
> Adviced by doug
> - add some error checking in probe
> - move "rockchip,rk808.h" into the patch about dt-bindings
>
> Changes in v4:
> Adviced by doug
> - add "clock-output-names" propertiey
> - add a header file "rockchip,rk808.h"
>
> Changes in v3:
> - fix compile err
>
> Changes in v2:
> Adviced by javier.martinez
> - separated from rtc-rk808.c
>
> Documentation/devicetree/bindings/mfd/rk808.txt | 142 +++++++++++++++++++++++
> include/dt-bindings/clock/rockchip,rk808.h | 11 ++
> 2 files changed, 153 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mfd/rk808.txt
> create mode 100644 include/dt-bindings/clock/rockchip,rk808.h
>
> diff --git a/Documentation/devicetree/bindings/mfd/rk808.txt b/Documentation/devicetree/bindings/mfd/rk808.txt
> new file mode 100644
> index 0000000..e5786e9
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/rk808.txt
> @@ -0,0 +1,142 @@
> +RK808 Power Management Integrated Circuit
> +
> +Required properties:
> +- compatible: "rockchip,rk808"
> +- reg: I2C slave address
> +- interrupt-parent: The parent interrupt controller.
> +- interrupts: the interrupt outputs of the controller.
> +- pinctrl-names: Should contain only one value - "default".
> +- pinctrl-0: Should specify pin control groups used for this controller.
You could probably skip including the pinctrl stuff here. Keep it in
the example. Nothing in the driver requires this and it's really an
artifact of the board.
> +- regulators: This is the list of child nodes that specify the regulator
Technically "regulators" is not a property, it's a child node. See
max8998 maybe for a sample, where it says:
Regulators: All the regulators of MAX8998 to be instantiated shall be
listed in a child node named 'regulators'. Each regulator is represented
by a child node of the 'regulators' node.
regulator-name {
/* standard regulator bindings here */
};
> + initialization data for defined regulators. Not all regulators for the given
> + device need to be present. The definition for each of these nodes is defined
> + using the standard binding for regulators found at
> + Documentation/devicetree/bindings/regulator/regulator.txt.
> +- #clock-cells: the value should be 1
> +- The following are the names of the regulators that the rk808 pmic block
> + supports. Note: The 'n' below represents the number as per the datasheet:
> +
> + - DCDC_REGn
> + - valid values for n are 1 to 4.
> + - LDO_REGn
> + - valid values for n are 1 to 8.
> + - SWITCH_REGn
> + - valid values for n are 1 to 2.
> +
> +Optional properties:
> +- clock-output-names : From common clock binding to override the
> + default output clock name
nit: no space before the ":"
> +- rockchip,system-power-controller: Telling whether or not this pmic is controlling
> + the system power.
> +
> +Example:
> +rk808: pmic@1b {
> + compatible = "rockchip,rk808";
> + interrupt-parent = <&gpio0>;
> + interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_int>;
> + reg = <0x1b>;
> + #clock-cells = <1>;
> + clock-output-names = "xin32k0", "xin32k1";
> + rockchip,system-power-controller;
> +
> + regulators {
nit: you've indented regulators one too many spots.
> + rk808_dcdc1_reg: DCDC_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-name = "vdd_arm";
> + };
> +
> + rk808_dcdc2_reg: DCDC_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <1250000>;
> + regulator-name = "vdd_gpu";
> + };
> +
> + rk808_dcdc3_reg: DCDC_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vdd_ddr";
> + };
> +
> + rk808_dcdc4_reg: DCDC_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vccio";
> + };
> +
> + rk808_ldo1_reg: LDO_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + rk808_ldo2_reg: LDO_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + rk808_ldo3_reg: LDO_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-name = "LDO_REG3";
> + };
> +
> + rk808_ldo4_reg: LDO_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + rk808_ldo5_reg: LDO_REG5 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + rk808_ldo6_reg: LDO_REG6 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + };
> +
> + rk808_ldo7_reg: LDO_REG7 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + rk808_ldo8_reg: LDO_REG8 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + rk808_switch1_reg: SWITCH_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + rk808_switch2_reg: SWITCH_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + };
> + };
> + };
> diff --git a/include/dt-bindings/clock/rockchip,rk808.h b/include/dt-bindings/clock/rockchip,rk808.h
> new file mode 100644
> index 0000000..1a87343
> --- /dev/null
> +++ b/include/dt-bindings/clock/rockchip,rk808.h
> @@ -0,0 +1,11 @@
> +/*
> + * This header provides constants clk index RK808 pmic clkout
> + */
> +#ifndef _CLK_ROCKCHIP_RK808
> +#define _CLK_ROCKCHIP_RK808
> +
> +/* CLOCKOUT index */
> +#define RK808_CLKOUT0 0
> +#define RK808_CLKOUT1 1
> +
> +#endif
IMHO nothing above is terrible, but it would be nice to spin it if
possible. After those small cleanups I personally think this is ready
to land.
-Doug
^ permalink raw reply [flat|nested] 4+ messages in thread* Re: [PATCH v5 1/5] dt-bindings: Add RK808 device tree bindings document
2014-08-25 13:29 [PATCH v5 1/5] dt-bindings: Add RK808 device tree bindings document Chris Zhong
2014-08-25 20:14 ` Doug Anderson
@ 2014-08-26 9:42 ` Mark Rutland
1 sibling, 0 replies; 4+ messages in thread
From: Mark Rutland @ 2014-08-26 9:42 UTC (permalink / raw)
To: Chris Zhong
Cc: robh+dt@kernel.org, Pawel Moll, ijc+devicetree@hellion.org.uk,
galak@codeaurora.org, sameo@linux.intel.com, lee.jones@linaro.org,
lgirdwood@gmail.com, broonie@kernel.org, a.zummo@towertech.it,
mturquette@linaro.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, rtc-linux@googlegroups.com,
grant.likely@linaro.org, hl@rock-chips.com,
huangtao@rock-chips.com, cf@rock-chips.com,
zhangqing@rock-chips.com
On Mon, Aug 25, 2014 at 02:29:22PM +0100, Chris Zhong wrote:
> Add device tree bindings documentation and a header file
> for rockchip's RK808 pmic.
>
> Signed-off-by: Chris Zhong <zyw@rock-chips.com>
>
> ---
>
> Changes in v5:
> Adviced by doug
> - add some error checking in probe
> - move "rockchip,rk808.h" into the patch about dt-bindings
>
> Changes in v4:
> Adviced by doug
> - add "clock-output-names" propertiey
> - add a header file "rockchip,rk808.h"
>
> Changes in v3:
> - fix compile err
>
> Changes in v2:
> Adviced by javier.martinez
> - separated from rtc-rk808.c
>
> Documentation/devicetree/bindings/mfd/rk808.txt | 142 +++++++++++++++++++++++
> include/dt-bindings/clock/rockchip,rk808.h | 11 ++
> 2 files changed, 153 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mfd/rk808.txt
> create mode 100644 include/dt-bindings/clock/rockchip,rk808.h
>
> diff --git a/Documentation/devicetree/bindings/mfd/rk808.txt b/Documentation/devicetree/bindings/mfd/rk808.txt
> new file mode 100644
> index 0000000..e5786e9
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/rk808.txt
> @@ -0,0 +1,142 @@
> +RK808 Power Management Integrated Circuit
> +
> +Required properties:
> +- compatible: "rockchip,rk808"
> +- reg: I2C slave address
> +- interrupt-parent: The parent interrupt controller.
> +- interrupts: the interrupt outputs of the controller.
> +- pinctrl-names: Should contain only one value - "default".
> +- pinctrl-0: Should specify pin control groups used for this controller.
> +- regulators: This is the list of child nodes that specify the regulator
> + initialization data for defined regulators. Not all regulators for the given
> + device need to be present. The definition for each of these nodes is defined
> + using the standard binding for regulators found at
> + Documentation/devicetree/bindings/regulator/regulator.txt.
> +- #clock-cells: the value should be 1
It would be nice to have a description of the valid values.
They look to be 0 and 1 in include/dt-bindings/clock/rockchip,rk808.h.
Thanks,
Mark.
> +- The following are the names of the regulators that the rk808 pmic block
> + supports. Note: The 'n' below represents the number as per the datasheet:
> +
> + - DCDC_REGn
> + - valid values for n are 1 to 4.
> + - LDO_REGn
> + - valid values for n are 1 to 8.
> + - SWITCH_REGn
> + - valid values for n are 1 to 2.
> +
> +Optional properties:
> +- clock-output-names : From common clock binding to override the
> + default output clock name
> +- rockchip,system-power-controller: Telling whether or not this pmic is controlling
> + the system power.
> +
> +Example:
> +rk808: pmic@1b {
> + compatible = "rockchip,rk808";
> + interrupt-parent = <&gpio0>;
> + interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_int>;
> + reg = <0x1b>;
> + #clock-cells = <1>;
> + clock-output-names = "xin32k0", "xin32k1";
> + rockchip,system-power-controller;
> +
> + regulators {
> + rk808_dcdc1_reg: DCDC_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-name = "vdd_arm";
> + };
> +
> + rk808_dcdc2_reg: DCDC_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <1250000>;
> + regulator-name = "vdd_gpu";
> + };
> +
> + rk808_dcdc3_reg: DCDC_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vdd_ddr";
> + };
> +
> + rk808_dcdc4_reg: DCDC_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-name = "vccio";
> + };
> +
> + rk808_ldo1_reg: LDO_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + rk808_ldo2_reg: LDO_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + rk808_ldo3_reg: LDO_REG3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-name = "LDO_REG3";
> + };
> +
> + rk808_ldo4_reg: LDO_REG4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + rk808_ldo5_reg: LDO_REG5 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + rk808_ldo6_reg: LDO_REG6 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + };
> +
> + rk808_ldo7_reg: LDO_REG7 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + rk808_ldo8_reg: LDO_REG8 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + rk808_switch1_reg: SWITCH_REG1 {
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + rk808_switch2_reg: SWITCH_REG2 {
> + regulator-always-on;
> + regulator-boot-on;
> + };
> + };
> + };
> diff --git a/include/dt-bindings/clock/rockchip,rk808.h b/include/dt-bindings/clock/rockchip,rk808.h
> new file mode 100644
> index 0000000..1a87343
> --- /dev/null
> +++ b/include/dt-bindings/clock/rockchip,rk808.h
> @@ -0,0 +1,11 @@
> +/*
> + * This header provides constants clk index RK808 pmic clkout
> + */
> +#ifndef _CLK_ROCKCHIP_RK808
> +#define _CLK_ROCKCHIP_RK808
> +
> +/* CLOCKOUT index */
> +#define RK808_CLKOUT0 0
> +#define RK808_CLKOUT1 1
> +
> +#endif
> --
> 1.7.9.5
>
>
> --
> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2014-08-26 9:42 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2014-08-25 13:29 [PATCH v5 1/5] dt-bindings: Add RK808 device tree bindings document Chris Zhong
2014-08-25 20:14 ` Doug Anderson
[not found] ` <CAD=FV=Wp7e__00WAcXZB-kZZ28hsnWwq+eYOYeeDMYNQVSmkzA-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2014-08-26 2:18 ` Chris Zhong
2014-08-26 9:42 ` Mark Rutland
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).