From: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
To: Qais Yousef <qais.yousef@imgtec.com>,
Clemens Ladisch <clemens@ladisch.de>,
linux-kernel@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
alsa-devel@alsa-project.org, Neil Jones <neil.jones@imgtec.com>,
Arnd Bergmann <arnd@arndb.de>,
devicetree@vger.kernel.org
Subject: Re: [alsa-devel] [PATCH 00/11] Add AXD Audio Processing IP driver
Date: Wed, 29 Oct 2014 10:06:19 -0500 [thread overview]
Message-ID: <5451026B.9030306@linux.intel.com> (raw)
In-Reply-To: <544F97A4.7080209@imgtec.com>
On 10/28/14, 8:18 AM, Qais Yousef wrote:
> On 10/28/2014 11:55 AM, Clemens Ladisch wrote:
>> Qais Yousef wrote:
>>> AXD Audio Processing IP performs audio decoding, encoding, mixing,
>>> equalisation,
>>> synchronisation and playback.
>> What exactly do you mean with "synchronisation" and "playback"?
>
> Synchronisation refers to accurate audio playout relative to a master
> clock source including compensation of drift between the master clock
> source and the playout clock of the audio hardware. Hence allowing
> synchronised audio playout across multiple independent devices.
>
> Playback simple refers to the fact that AXD is capable of managing audio
> playout hardware like I2S and SPDIF interfaces.
>
>
>>> It doesn't fit in alsa subsystem but I Cced them to confirm.
>> ... because those two words sound like something that a sound card
>> could do.
>
> The problem mainly stems from the fact that we take a variety of
> compressed audio as input and we could perform audio encoding. The
> problem with the compressed audio is that the range of decoders and
> configuration supported in alsa is limited and there's no support for
> taking raw pcm and producing compressed output. I'm not an expert on
> alsa but when I looked it looked like there's more infra structure
> required.
>
> The following not supported points from
> Documentation/sound/alsa/compress_offload.txt affect us:
>
> - Volume control/routing is not handled by this API. Devices exposing a
> compressed data interface will be considered as regular ALSA devices;
> volume changes and routing information will be provided with regular
> ALSA kcontrols.
>
> - Embedded audio effects. Such effects should be enabled in the same
> manner, no matter if the input was PCM or compressed.
>
> - Encoding/decoding acceleration is not supported as mentioned
> above. It is possible to route the output of a decoder to a capture
> stream, or even implement transcoding capabilities. This routing
> would be enabled with ALSA kcontrols.
Volume control, effects and routing aren't supported directly with the
snd_pcm streaming interface either. we didn't add these features either
in the compressed API since they could be enabled through existing means
(kcontrols and routing).
>
>
>
>>> I added it to drivers/char as this is the best location I could think
>>> of at the
>>> moment.
>> drivers/misc?
>
> Yeah could do if there's consensus.
>
> Thanks,
> Qais
>
>>
>> Regards,
>> Clemens
>
> _______________________________________________
> Alsa-devel mailing list
> Alsa-devel@alsa-project.org
> http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
next prev parent reply other threads:[~2014-10-29 15:06 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-10-28 11:26 [PATCH 00/11] Add AXD Audio Processing IP driver Qais Yousef
2014-10-28 11:26 ` [PATCH 02/11] dt: bindings: add AXD Audio Processing IP binding document Qais Yousef
2014-10-28 11:26 ` [PATCH 03/11] drivers: char: add AXD Audio Processing IP driver Qais Yousef
2014-10-28 14:10 ` Greg Kroah-Hartman
[not found] ` <20141028141038.GA18384-U8xfFu+wG4EAvxtiuMwx3w@public.gmane.org>
2014-10-28 14:36 ` Qais Yousef
[not found] ` <544FA9F7.1020101-1AXoQHu6uovQT0dZR+AlfA@public.gmane.org>
2014-10-28 14:50 ` Greg Kroah-Hartman
2014-10-29 5:33 ` [alsa-devel] " Vinod Koul
2014-10-28 11:55 ` [PATCH 00/11] Add " Clemens Ladisch
2014-10-28 13:18 ` Qais Yousef
[not found] ` <544F97A4.7080209-1AXoQHu6uovQT0dZR+AlfA@public.gmane.org>
2014-10-28 14:13 ` Greg Kroah-Hartman
2014-10-28 15:05 ` Qais Yousef
2014-10-29 2:50 ` Greg Kroah-Hartman
2014-10-29 5:24 ` [alsa-devel] " Vinod Koul
2014-10-29 10:48 ` Qais Yousef
2014-10-29 5:20 ` Vinod Koul
2014-10-28 14:54 ` Lars-Peter Clausen
2014-10-28 15:33 ` Qais Yousef
2014-10-28 16:04 ` [alsa-devel] " Lars-Peter Clausen
2014-10-29 5:18 ` Vinod Koul
2014-10-29 15:06 ` Pierre-Louis Bossart [this message]
2014-10-28 12:06 ` Lars-Peter Clausen
2014-10-28 13:21 ` Qais Yousef
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5451026B.9030306@linux.intel.com \
--to=pierre-louis.bossart@linux.intel.com \
--cc=alsa-devel@alsa-project.org \
--cc=arnd@arndb.de \
--cc=clemens@ladisch.de \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=linux-kernel@vger.kernel.org \
--cc=neil.jones@imgtec.com \
--cc=qais.yousef@imgtec.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).