Re: [PATCH 6/7] phy: omap-usb2: Add a new compatible string for USB2 PHY2

[Kishon Vijay Abraham I <kishon@ti.com>]

Hi Roger,

On Wednesday 05 August 2015 01:55 PM, Roger Quadros wrote:
> On 05/08/15 11:23, Roger Quadros wrote:
>>
>> On 04/08/15 18:20, Kishon Vijay Abraham I wrote:
>>> The USB2 PHY2 has a different register map compared to USB2 PHY1
>>> to power on/off the PHY. In order to handle it, add a new
>>> "compatible" string.
>>>
>>> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
>>> ---
>>>  Documentation/devicetree/bindings/phy/ti-phy.txt |    2 ++
>>>  drivers/phy/phy-omap-usb2.c                      |    9 +++++++++
>>>  2 files changed, 11 insertions(+)
>>>
>>> diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt
>>> index 49e5b0c..a061077 100644
>>> --- a/Documentation/devicetree/bindings/phy/ti-phy.txt
>>> +++ b/Documentation/devicetree/bindings/phy/ti-phy.txt
>>> @@ -31,6 +31,8 @@ OMAP USB2 PHY
>>>  
>>>  Required properties:
>>>   - compatible: Should be "ti,omap-usb2"
>>> +	       Should be "ti,dra7x-usb2-phy2" for the 2nd instance of USB2 PHY
>>> +	       in DRA7x
>>>   - reg : Address and length of the register set for the device.
>>>   - #phy-cells: determine the number of cells that should be given in the
>>>     phandle while referencing this phy.
>>> diff --git a/drivers/phy/phy-omap-usb2.c b/drivers/phy/phy-omap-usb2.c
>>> index b5c266a..2f7220f 100644
>>> --- a/drivers/phy/phy-omap-usb2.c
>>> +++ b/drivers/phy/phy-omap-usb2.c
>>> @@ -159,6 +159,11 @@ static const struct usb_phy_data dra7x_usb2_data = {
>>>  	.flags = OMAP_USB2_CALIBRATE_FALSE_DISCONNECT,
>>>  };
>>>  
>>> +static const struct usb_phy_data dra7x_usb2_phy2_data = {
>>> +	.label = "dra7x_usb2_phy2",
>>> +	.flags = OMAP_USB2_CALIBRATE_FALSE_DISCONNECT,
>>> +};
>>> +
>>>  static const struct usb_phy_data am437x_usb2_data = {
>>>  	.label = "am437x_usb2",
>>>  	.flags =  0,
>>> @@ -178,6 +183,10 @@ static const struct of_device_id omap_usb2_id_table[] = {
>>>  		.data = &dra7x_usb2_data,
>>>  	},
>>>  	{
>>> +		.compatible = "ti,dra7x-usb2-phy2",
>>> +		.data = &dra7x_usb2_phy2_data,
>>
>> Why is this needed? You can reuse dra7x_usb2_data as is.
> 
> OK. I see why we need it in the next patch.
> Probably both patches could be squashed.
> 
> What does .label indicate?

it's actually used only in usb_add_phy() (drivers/usb/phy/phy.c). I don't think
it's actually important unless you strongly feel so.

Thanks
Kishon