* [PATCH 1/3] ARM: dts: exynos5422-odroidxu3: use cd-gpio method to detect sd-card
@ 2015-10-11 15:46 Anand Moon
2015-10-11 15:46 ` [PATCH 2/3] ARM: dts: use vmmc-supply of emmc/sd for exynos5422-odroidxu3 Anand Moon
` (2 more replies)
0 siblings, 3 replies; 50+ messages in thread
From: Anand Moon @ 2015-10-11 15:46 UTC (permalink / raw)
To: Kukjin Kim, Krzysztof Kozlowski, Javier Martinez Canillas,
Anand Moon, Lukasz Majewski, Jaehoon Chung
Cc: devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel
From: Jaehoon Chung <jh80.chung@samsung.com>
To detect sd-card use the cd-gpio method.
It can decrease the interrupt for detecting sd-card.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
---
Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch
---
arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
index 1af5bdc..26decbd 100644
--- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
+++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
@@ -352,8 +352,10 @@
samsung,dw-mshc-ciu-div = <3>;
samsung,dw-mshc-sdr-timing = <0 4>;
samsung,dw-mshc-ddr-timing = <0 2>;
+ cd-gpios = <&gpc2 2 GPIO_ACTIVE_HIGH>;
+ cd-inverted;
pinctrl-names = "default";
- pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>;
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
bus-width = <4>;
cap-sd-highspeed;
};
--
2.1.4
^ permalink raw reply related [flat|nested] 50+ messages in thread* [PATCH 2/3] ARM: dts: use vmmc-supply of emmc/sd for exynos5422-odroidxu3 2015-10-11 15:46 [PATCH 1/3] ARM: dts: exynos5422-odroidxu3: use cd-gpio method to detect sd-card Anand Moon @ 2015-10-11 15:46 ` Anand Moon 2015-10-12 4:42 ` Krzysztof Kozlowski 2015-10-11 15:46 ` [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support Anand Moon 2015-10-12 4:29 ` [PATCH 1/3] ARM: dts: exynos5422-odroidxu3: use cd-gpio method to detect sd-card Krzysztof Kozlowski 2 siblings, 1 reply; 50+ messages in thread From: Anand Moon @ 2015-10-11 15:46 UTC (permalink / raw) To: Kukjin Kim, Krzysztof Kozlowski, Javier Martinez Canillas, Anand Moon, Lukasz Majewski, Jaehoon Chung Cc: devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel Added support for vmmc/vqmmc-supply for emmc/sd cards. Fixed the min values for regulator ldo13_reg (VDDQ_MMC2). Added ramp-delay for LDO9(VDD33_USB3_0). Added ramp-delay for LDO13(VDDQ_MMC2). Added ramp-delay for LDO15(ETH_P3V3). Signed-off-by: Anand Moon <linux.amoon@gmail.com> --- Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch Note: Changes need for support of UHS-I highspeed cards. changes for vqmmc-supply for emmc is not supported. [ 1.831136] vdd_ldo9: ramp_delay not set [ 1.843049] vdd_ldo13: ramp_delay not set [ 1.850975] vdd_ldo15: ramp_delay not set [ 1.862816] vdd_sd: ramp_delay not set --- arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi index 26decbd..58c06d3 100644 --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi @@ -157,6 +157,7 @@ regulator-min-microvolt = <3000000>; regulator-max-microvolt = <3000000>; regulator-always-on; + regulator-ramp-delay = <12000>; }; ldo10_reg: LDO10 { @@ -182,9 +183,10 @@ ldo13_reg: LDO13 { regulator-name = "vdd_ldo13"; - regulator-min-microvolt = <2800000>; + regulator-min-microvolt = <1800000>; regulator-max-microvolt = <2800000>; regulator-always-on; + regulator-ramp-delay = <12000>; }; ldo15_reg: LDO15 { @@ -213,6 +215,7 @@ regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; regulator-always-on; + regulator-ramp-delay = <12000>; }; ldo24_reg: LDO24 { @@ -338,6 +341,7 @@ samsung,dw-mshc-ddr-timing = <0 2>; samsung,dw-mshc-hs400-timing = <0 2>; samsung,read-strobe-delay = <90>; + vmmc-supply = <&ldo3_reg>; pinctrl-names = "default"; pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8 &sd0_cd &sd0_rclk>; bus-width = <8>; @@ -352,6 +356,8 @@ samsung,dw-mshc-ciu-div = <3>; samsung,dw-mshc-sdr-timing = <0 4>; samsung,dw-mshc-ddr-timing = <0 2>; + vmmc-supply = <&ldo19_reg>; + vqmmc-supply = <&ldo13_reg>; cd-gpios = <&gpc2 2 GPIO_ACTIVE_HIGH>; cd-inverted; pinctrl-names = "default"; -- 2.1.4 ^ permalink raw reply related [flat|nested] 50+ messages in thread
* Re: [PATCH 2/3] ARM: dts: use vmmc-supply of emmc/sd for exynos5422-odroidxu3 2015-10-11 15:46 ` [PATCH 2/3] ARM: dts: use vmmc-supply of emmc/sd for exynos5422-odroidxu3 Anand Moon @ 2015-10-12 4:42 ` Krzysztof Kozlowski 2015-10-12 5:49 ` Krzysztof Kozlowski 0 siblings, 1 reply; 50+ messages in thread From: Krzysztof Kozlowski @ 2015-10-12 4:42 UTC (permalink / raw) To: Anand Moon, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung Cc: devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel On 12.10.2015 00:46, Anand Moon wrote: > Added support for vmmc/vqmmc-supply for emmc/sd cards. > Fixed the min values for regulator ldo13_reg (VDDQ_MMC2). I can't see the description of a problem which is fixed. If you fix something, then please describe what is wrong. > Added ramp-delay for LDO9(VDD33_USB3_0). > Added ramp-delay for LDO13(VDDQ_MMC2). > Added ramp-delay for LDO15(ETH_P3V3). > > Signed-off-by: Anand Moon <linux.amoon@gmail.com> > > --- > Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch > > Note: > Changes need for support of UHS-I highspeed cards. > changes for vqmmc-supply for emmc is not supported. > > [ 1.831136] vdd_ldo9: ramp_delay not set > [ 1.843049] vdd_ldo13: ramp_delay not set > [ 1.850975] vdd_ldo15: ramp_delay not set > [ 1.862816] vdd_sd: ramp_delay not set > --- > arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 8 +++++++- > 1 file changed, 7 insertions(+), 1 deletion(-) > > diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi > index 26decbd..58c06d3 100644 > --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi > +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi > @@ -157,6 +157,7 @@ > regulator-min-microvolt = <3000000>; > regulator-max-microvolt = <3000000>; > regulator-always-on; > + regulator-ramp-delay = <12000>; > }; > > ldo10_reg: LDO10 { > @@ -182,9 +183,10 @@ > > ldo13_reg: LDO13 { > regulator-name = "vdd_ldo13"; > - regulator-min-microvolt = <2800000>; > + regulator-min-microvolt = <1800000>; > regulator-max-microvolt = <2800000>; > regulator-always-on; > + regulator-ramp-delay = <12000>; > }; > > ldo15_reg: LDO15 { > @@ -213,6 +215,7 @@ > regulator-min-microvolt = <2800000>; > regulator-max-microvolt = <2800000>; > regulator-always-on; > + regulator-ramp-delay = <12000>; Where did you get this value from? It looks wrong... My datasheet does not have 12000 uV/uS. > }; > > ldo24_reg: LDO24 { > @@ -338,6 +341,7 @@ > samsung,dw-mshc-ddr-timing = <0 2>; > samsung,dw-mshc-hs400-timing = <0 2>; > samsung,read-strobe-delay = <90>; > + vmmc-supply = <&ldo3_reg>; > pinctrl-names = "default"; > pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8 &sd0_cd &sd0_rclk>; > bus-width = <8>; > @@ -352,6 +356,8 @@ > samsung,dw-mshc-ciu-div = <3>; > samsung,dw-mshc-sdr-timing = <0 4>; > samsung,dw-mshc-ddr-timing = <0 2>; > + vmmc-supply = <&ldo19_reg>; > + vqmmc-supply = <&ldo13_reg>; It looks wrong. LDO13 is used in one place as VQMMC and in other as VMMC. How did you figure out which regulator supplies which power domain? Best regards, Krzysztof > cd-gpios = <&gpc2 2 GPIO_ACTIVE_HIGH>; > cd-inverted; > pinctrl-names = "default"; > ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 2/3] ARM: dts: use vmmc-supply of emmc/sd for exynos5422-odroidxu3 2015-10-12 4:42 ` Krzysztof Kozlowski @ 2015-10-12 5:49 ` Krzysztof Kozlowski 2015-10-12 11:08 ` Anand Moon 0 siblings, 1 reply; 50+ messages in thread From: Krzysztof Kozlowski @ 2015-10-12 5:49 UTC (permalink / raw) To: Anand Moon, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung Cc: devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel On 12.10.2015 13:42, Krzysztof Kozlowski wrote: > On 12.10.2015 00:46, Anand Moon wrote: >> Added support for vmmc/vqmmc-supply for emmc/sd cards. >> Fixed the min values for regulator ldo13_reg (VDDQ_MMC2). > > I can't see the description of a problem which is fixed. If you fix > something, then please describe what is wrong. > >> Added ramp-delay for LDO9(VDD33_USB3_0). >> Added ramp-delay for LDO13(VDDQ_MMC2). >> Added ramp-delay for LDO15(ETH_P3V3). >> >> Signed-off-by: Anand Moon <linux.amoon@gmail.com> >> >> --- >> Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch >> >> Note: >> Changes need for support of UHS-I highspeed cards. >> changes for vqmmc-supply for emmc is not supported. >> >> [ 1.831136] vdd_ldo9: ramp_delay not set >> [ 1.843049] vdd_ldo13: ramp_delay not set >> [ 1.850975] vdd_ldo15: ramp_delay not set >> [ 1.862816] vdd_sd: ramp_delay not set >> --- >> arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 8 +++++++- >> 1 file changed, 7 insertions(+), 1 deletion(-) >> >> diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >> index 26decbd..58c06d3 100644 >> --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >> +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >> @@ -157,6 +157,7 @@ >> regulator-min-microvolt = <3000000>; >> regulator-max-microvolt = <3000000>; >> regulator-always-on; >> + regulator-ramp-delay = <12000>; >> }; >> >> ldo10_reg: LDO10 { >> @@ -182,9 +183,10 @@ >> >> ldo13_reg: LDO13 { >> regulator-name = "vdd_ldo13"; >> - regulator-min-microvolt = <2800000>; >> + regulator-min-microvolt = <1800000>; >> regulator-max-microvolt = <2800000>; >> regulator-always-on; >> + regulator-ramp-delay = <12000>; >> }; >> >> ldo15_reg: LDO15 { >> @@ -213,6 +215,7 @@ >> regulator-min-microvolt = <2800000>; >> regulator-max-microvolt = <2800000>; >> regulator-always-on; >> + regulator-ramp-delay = <12000>; > > Where did you get this value from? It looks wrong... My datasheet does > not have 12000 uV/uS. Anand, We have actually been here: http://lists.infradead.org/pipermail/linux-arm-kernel/2015-June/351601.html That time you used 8000. I asked the same question - how did you figure out the exact value. Now we have the same question - why 12000? It is completely fine to make a mistake (I do a lot of them) but please try not to make the same mistake again. BR, Krzysztof > >> }; >> >> ldo24_reg: LDO24 { >> @@ -338,6 +341,7 @@ >> samsung,dw-mshc-ddr-timing = <0 2>; >> samsung,dw-mshc-hs400-timing = <0 2>; >> samsung,read-strobe-delay = <90>; >> + vmmc-supply = <&ldo3_reg>; >> pinctrl-names = "default"; >> pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8 &sd0_cd &sd0_rclk>; >> bus-width = <8>; >> @@ -352,6 +356,8 @@ >> samsung,dw-mshc-ciu-div = <3>; >> samsung,dw-mshc-sdr-timing = <0 4>; >> samsung,dw-mshc-ddr-timing = <0 2>; >> + vmmc-supply = <&ldo19_reg>; >> + vqmmc-supply = <&ldo13_reg>; > > It looks wrong. LDO13 is used in one place as VQMMC and in other as > VMMC. How did you figure out which regulator supplies which power domain? > > Best regards, > Krzysztof > >> cd-gpios = <&gpc2 2 GPIO_ACTIVE_HIGH>; >> cd-inverted; >> pinctrl-names = "default"; >> > > ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 2/3] ARM: dts: use vmmc-supply of emmc/sd for exynos5422-odroidxu3 2015-10-12 5:49 ` Krzysztof Kozlowski @ 2015-10-12 11:08 ` Anand Moon 2015-10-12 12:13 ` Krzysztof Kozlowski 0 siblings, 1 reply; 50+ messages in thread From: Anand Moon @ 2015-10-12 11:08 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung, devicetree, linux-arm-kernel, linux-samsung-soc@vger.kernel.org, Linux Kernel Hi Krzysztof, On 12 October 2015 at 11:19, Krzysztof Kozlowski <k.kozlowski@samsung.com> wrote: > On 12.10.2015 13:42, Krzysztof Kozlowski wrote: >> On 12.10.2015 00:46, Anand Moon wrote: >>> Added support for vmmc/vqmmc-supply for emmc/sd cards. >>> Fixed the min values for regulator ldo13_reg (VDDQ_MMC2). >> >> I can't see the description of a problem which is fixed. If you fix >> something, then please describe what is wrong. >> >>> Added ramp-delay for LDO9(VDD33_USB3_0). >>> Added ramp-delay for LDO13(VDDQ_MMC2). >>> Added ramp-delay for LDO15(ETH_P3V3). >>> >>> Signed-off-by: Anand Moon <linux.amoon@gmail.com> >>> >>> --- >>> Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch >>> >>> Note: >>> Changes need for support of UHS-I highspeed cards. >>> changes for vqmmc-supply for emmc is not supported. >>> >>> [ 1.831136] vdd_ldo9: ramp_delay not set >>> [ 1.843049] vdd_ldo13: ramp_delay not set >>> [ 1.850975] vdd_ldo15: ramp_delay not set >>> [ 1.862816] vdd_sd: ramp_delay not set >>> --- >>> arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 8 +++++++- >>> 1 file changed, 7 insertions(+), 1 deletion(-) >>> >>> diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>> index 26decbd..58c06d3 100644 >>> --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>> +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>> @@ -157,6 +157,7 @@ >>> regulator-min-microvolt = <3000000>; >>> regulator-max-microvolt = <3000000>; >>> regulator-always-on; >>> + regulator-ramp-delay = <12000>; >>> }; >>> >>> ldo10_reg: LDO10 { >>> @@ -182,9 +183,10 @@ >>> >>> ldo13_reg: LDO13 { >>> regulator-name = "vdd_ldo13"; >>> - regulator-min-microvolt = <2800000>; >>> + regulator-min-microvolt = <1800000>; >>> regulator-max-microvolt = <2800000>; >>> regulator-always-on; >>> + regulator-ramp-delay = <12000>; >>> }; >>> >>> ldo15_reg: LDO15 { >>> @@ -213,6 +215,7 @@ >>> regulator-min-microvolt = <2800000>; >>> regulator-max-microvolt = <2800000>; >>> regulator-always-on; >>> + regulator-ramp-delay = <12000>; >> >> Where did you get this value from? It looks wrong... My datasheet does >> not have 12000 uV/uS. > > Anand, > > We have actually been here: > http://lists.infradead.org/pipermail/linux-arm-kernel/2015-June/351601.html > > That time you used 8000. I asked the same question - how did you figure > out the exact value. > > Now we have the same question - why 12000? > > It is completely fine to make a mistake (I do a lot of them) but please > try not to make the same mistake again. > > BR, > Krzysztof I will focus more in the future to clamp down my mistakes to minimal. > >> >>> }; >>> >>> ldo24_reg: LDO24 { >>> @@ -338,6 +341,7 @@ >>> samsung,dw-mshc-ddr-timing = <0 2>; >>> samsung,dw-mshc-hs400-timing = <0 2>; >>> samsung,read-strobe-delay = <90>; >>> + vmmc-supply = <&ldo3_reg>; >>> pinctrl-names = "default"; >>> pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8 &sd0_cd &sd0_rclk>; >>> bus-width = <8>; >>> @@ -352,6 +356,8 @@ >>> samsung,dw-mshc-ciu-div = <3>; >>> samsung,dw-mshc-sdr-timing = <0 4>; >>> samsung,dw-mshc-ddr-timing = <0 2>; >>> + vmmc-supply = <&ldo19_reg>; >>> + vqmmc-supply = <&ldo13_reg>; >> >> It looks wrong. LDO13 is used in one place as VQMMC and in other as >> VMMC. How did you figure out which regulator supplies which power domain? >> I refer Schematics diagram to XU4_MAIN_REV0.1.pdf >From the PWR_PMCI_S2MPS11_LDO_CTRL document it LDO13 point to VDDQ_MMC2. >> Best regards, >> Krzysztof >> >>> cd-gpios = <&gpc2 2 GPIO_ACTIVE_HIGH>; >>> cd-inverted; >>> pinctrl-names = "default"; >>> >> >> > -Anand Moon ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 2/3] ARM: dts: use vmmc-supply of emmc/sd for exynos5422-odroidxu3 2015-10-12 11:08 ` Anand Moon @ 2015-10-12 12:13 ` Krzysztof Kozlowski 2015-10-12 14:33 ` Anand Moon 0 siblings, 1 reply; 50+ messages in thread From: Krzysztof Kozlowski @ 2015-10-12 12:13 UTC (permalink / raw) To: Anand Moon Cc: k.kozlowski.k, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung, devicetree, linux-arm-kernel, linux-samsung-soc@vger.kernel.org, Linux Kernel W dniu 12.10.2015 o 20:08, Anand Moon pisze: > Hi Krzysztof, > > On 12 October 2015 at 11:19, Krzysztof Kozlowski > <k.kozlowski@samsung.com> wrote: >> On 12.10.2015 13:42, Krzysztof Kozlowski wrote: >>> On 12.10.2015 00:46, Anand Moon wrote: >>>> Added support for vmmc/vqmmc-supply for emmc/sd cards. >>>> Fixed the min values for regulator ldo13_reg (VDDQ_MMC2). >>> >>> I can't see the description of a problem which is fixed. If you fix >>> something, then please describe what is wrong. >>> >>>> Added ramp-delay for LDO9(VDD33_USB3_0). >>>> Added ramp-delay for LDO13(VDDQ_MMC2). >>>> Added ramp-delay for LDO15(ETH_P3V3). >>>> >>>> Signed-off-by: Anand Moon <linux.amoon@gmail.com> >>>> >>>> --- >>>> Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch >>>> >>>> Note: >>>> Changes need for support of UHS-I highspeed cards. >>>> changes for vqmmc-supply for emmc is not supported. >>>> >>>> [ 1.831136] vdd_ldo9: ramp_delay not set >>>> [ 1.843049] vdd_ldo13: ramp_delay not set >>>> [ 1.850975] vdd_ldo15: ramp_delay not set >>>> [ 1.862816] vdd_sd: ramp_delay not set >>>> --- >>>> arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 8 +++++++- >>>> 1 file changed, 7 insertions(+), 1 deletion(-) >>>> >>>> diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>> index 26decbd..58c06d3 100644 >>>> --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>> +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>> @@ -157,6 +157,7 @@ >>>> regulator-min-microvolt = <3000000>; >>>> regulator-max-microvolt = <3000000>; >>>> regulator-always-on; >>>> + regulator-ramp-delay = <12000>; >>>> }; >>>> >>>> ldo10_reg: LDO10 { >>>> @@ -182,9 +183,10 @@ >>>> >>>> ldo13_reg: LDO13 { >>>> regulator-name = "vdd_ldo13"; >>>> - regulator-min-microvolt = <2800000>; >>>> + regulator-min-microvolt = <1800000>; >>>> regulator-max-microvolt = <2800000>; >>>> regulator-always-on; >>>> + regulator-ramp-delay = <12000>; >>>> }; >>>> >>>> ldo15_reg: LDO15 { >>>> @@ -213,6 +215,7 @@ >>>> regulator-min-microvolt = <2800000>; >>>> regulator-max-microvolt = <2800000>; >>>> regulator-always-on; >>>> + regulator-ramp-delay = <12000>; >>> >>> Where did you get this value from? It looks wrong... My datasheet does >>> not have 12000 uV/uS. >> > >> Anand, >> >> We have actually been here: >> http://lists.infradead.org/pipermail/linux-arm-kernel/2015-June/351601.html >> >> That time you used 8000. I asked the same question - how did you figure >> out the exact value. >> >> Now we have the same question - why 12000? >> >> It is completely fine to make a mistake (I do a lot of them) but please >> try not to make the same mistake again. >> >> BR, >> Krzysztof > > I will focus more in the future to clamp down my mistakes to minimal. > >> >>> >>>> }; >>>> >>>> ldo24_reg: LDO24 { >>>> @@ -338,6 +341,7 @@ >>>> samsung,dw-mshc-ddr-timing = <0 2>; >>>> samsung,dw-mshc-hs400-timing = <0 2>; >>>> samsung,read-strobe-delay = <90>; >>>> + vmmc-supply = <&ldo3_reg>; >>>> pinctrl-names = "default"; >>>> pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8 &sd0_cd &sd0_rclk>; >>>> bus-width = <8>; >>>> @@ -352,6 +356,8 @@ >>>> samsung,dw-mshc-ciu-div = <3>; >>>> samsung,dw-mshc-sdr-timing = <0 4>; >>>> samsung,dw-mshc-ddr-timing = <0 2>; >>>> + vmmc-supply = <&ldo19_reg>; >>>> + vqmmc-supply = <&ldo13_reg>; >>> >>> It looks wrong. LDO13 is used in one place as VQMMC and in other as >>> VMMC. How did you figure out which regulator supplies which power domain? >>> > > I refer Schematics diagram to XU4_MAIN_REV0.1.pdf > > From the PWR_PMCI_S2MPS11_LDO_CTRL document it LDO13 point to VDDQ_MMC2. > Aaa right, by mistake I thought that you put LDO13 here and in the node before, but there is LDO3, not 13. You did this correctly. But I have two other questions: 1. Maybe these regulators now should not be always-enabled? 2. Why changing minimum voltage of LDO13 to 1.8V? The schematics says 2.8V. Best regards, Krzysztof ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 2/3] ARM: dts: use vmmc-supply of emmc/sd for exynos5422-odroidxu3 2015-10-12 12:13 ` Krzysztof Kozlowski @ 2015-10-12 14:33 ` Anand Moon 2015-10-13 0:10 ` Krzysztof Kozlowski 0 siblings, 1 reply; 50+ messages in thread From: Anand Moon @ 2015-10-12 14:33 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Krzysztof Kozłowski, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung, devicetree, linux-arm-kernel, linux-samsung-soc@vger.kernel.org, Linux Kernel Hi Krzysztof, On 12 October 2015 at 17:43, Krzysztof Kozlowski <k.kozlowski@samsung.com> wrote: > W dniu 12.10.2015 o 20:08, Anand Moon pisze: >> Hi Krzysztof, >> >> On 12 October 2015 at 11:19, Krzysztof Kozlowski >> <k.kozlowski@samsung.com> wrote: >>> On 12.10.2015 13:42, Krzysztof Kozlowski wrote: >>>> On 12.10.2015 00:46, Anand Moon wrote: >>>>> Added support for vmmc/vqmmc-supply for emmc/sd cards. >>>>> Fixed the min values for regulator ldo13_reg (VDDQ_MMC2). >>>> >>>> I can't see the description of a problem which is fixed. If you fix >>>> something, then please describe what is wrong. >>>> >>>>> Added ramp-delay for LDO9(VDD33_USB3_0). >>>>> Added ramp-delay for LDO13(VDDQ_MMC2). >>>>> Added ramp-delay for LDO15(ETH_P3V3). >>>>> >>>>> Signed-off-by: Anand Moon <linux.amoon@gmail.com> >>>>> >>>>> --- >>>>> Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch >>>>> >>>>> Note: >>>>> Changes need for support of UHS-I highspeed cards. >>>>> changes for vqmmc-supply for emmc is not supported. >>>>> >>>>> [ 1.831136] vdd_ldo9: ramp_delay not set >>>>> [ 1.843049] vdd_ldo13: ramp_delay not set >>>>> [ 1.850975] vdd_ldo15: ramp_delay not set >>>>> [ 1.862816] vdd_sd: ramp_delay not set >>>>> --- >>>>> arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 8 +++++++- >>>>> 1 file changed, 7 insertions(+), 1 deletion(-) >>>>> >>>>> diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>>> index 26decbd..58c06d3 100644 >>>>> --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>>> +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>>> @@ -157,6 +157,7 @@ >>>>> regulator-min-microvolt = <3000000>; >>>>> regulator-max-microvolt = <3000000>; >>>>> regulator-always-on; >>>>> + regulator-ramp-delay = <12000>; >>>>> }; >>>>> >>>>> ldo10_reg: LDO10 { >>>>> @@ -182,9 +183,10 @@ >>>>> >>>>> ldo13_reg: LDO13 { >>>>> regulator-name = "vdd_ldo13"; >>>>> - regulator-min-microvolt = <2800000>; >>>>> + regulator-min-microvolt = <1800000>; >>>>> regulator-max-microvolt = <2800000>; >>>>> regulator-always-on; >>>>> + regulator-ramp-delay = <12000>; >>>>> }; >>>>> >>>>> ldo15_reg: LDO15 { >>>>> @@ -213,6 +215,7 @@ >>>>> regulator-min-microvolt = <2800000>; >>>>> regulator-max-microvolt = <2800000>; >>>>> regulator-always-on; >>>>> + regulator-ramp-delay = <12000>; >>>> >>>> Where did you get this value from? It looks wrong... My datasheet does >>>> not have 12000 uV/uS. >>> >> >>> Anand, >>> >>> We have actually been here: >>> http://lists.infradead.org/pipermail/linux-arm-kernel/2015-June/351601.html >>> >>> That time you used 8000. I asked the same question - how did you figure >>> out the exact value. >>> >>> Now we have the same question - why 12000? >>> >>> It is completely fine to make a mistake (I do a lot of them) but please >>> try not to make the same mistake again. >>> >>> BR, >>> Krzysztof >> >> I will focus more in the future to clamp down my mistakes to minimal. >> >>> >>>> >>>>> }; >>>>> >>>>> ldo24_reg: LDO24 { >>>>> @@ -338,6 +341,7 @@ >>>>> samsung,dw-mshc-ddr-timing = <0 2>; >>>>> samsung,dw-mshc-hs400-timing = <0 2>; >>>>> samsung,read-strobe-delay = <90>; >>>>> + vmmc-supply = <&ldo3_reg>; >>>>> pinctrl-names = "default"; >>>>> pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8 &sd0_cd &sd0_rclk>; >>>>> bus-width = <8>; >>>>> @@ -352,6 +356,8 @@ >>>>> samsung,dw-mshc-ciu-div = <3>; >>>>> samsung,dw-mshc-sdr-timing = <0 4>; >>>>> samsung,dw-mshc-ddr-timing = <0 2>; >>>>> + vmmc-supply = <&ldo19_reg>; >>>>> + vqmmc-supply = <&ldo13_reg>; >>>> >>>> It looks wrong. LDO13 is used in one place as VQMMC and in other as >>>> VMMC. How did you figure out which regulator supplies which power domain? >>>> >> >> I refer Schematics diagram to XU4_MAIN_REV0.1.pdf >> >> From the PWR_PMCI_S2MPS11_LDO_CTRL document it LDO13 point to VDDQ_MMC2. >> > > Aaa right, by mistake I thought that you put LDO13 here and in the node > before, but there is LDO3, not 13. You did this correctly. > > But I have two other questions: > 1. Maybe these regulators now should not be always-enabled? regulator-always-on can be removed: I have tested this. > 2. Why changing minimum voltage of LDO13 to 1.8V? The schematics says 2.8V. > In the schematics diagram to XU4_MAIN_REV0.1.pdf >From the EXYNOS5422 MMC UFS diagram CH2 range is VDDQ_MMC2 (1.8V/2.8V). -Anand Moon > Best regards, > Krzysztof > > ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 2/3] ARM: dts: use vmmc-supply of emmc/sd for exynos5422-odroidxu3 2015-10-12 14:33 ` Anand Moon @ 2015-10-13 0:10 ` Krzysztof Kozlowski 2015-10-13 2:29 ` Anand Moon 0 siblings, 1 reply; 50+ messages in thread From: Krzysztof Kozlowski @ 2015-10-13 0:10 UTC (permalink / raw) To: Anand Moon Cc: Krzysztof Kozłowski, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung, devicetree, linux-arm-kernel, linux-samsung-soc@vger.kernel.org, Linux Kernel On 12.10.2015 23:33, Anand Moon wrote: > Hi Krzysztof, > > On 12 October 2015 at 17:43, Krzysztof Kozlowski > <k.kozlowski@samsung.com> wrote: >> W dniu 12.10.2015 o 20:08, Anand Moon pisze: >>> Hi Krzysztof, >>> >>> On 12 October 2015 at 11:19, Krzysztof Kozlowski >>> <k.kozlowski@samsung.com> wrote: >>>> On 12.10.2015 13:42, Krzysztof Kozlowski wrote: >>>>> On 12.10.2015 00:46, Anand Moon wrote: >>>>>> Added support for vmmc/vqmmc-supply for emmc/sd cards. >>>>>> Fixed the min values for regulator ldo13_reg (VDDQ_MMC2). >>>>> >>>>> I can't see the description of a problem which is fixed. If you fix >>>>> something, then please describe what is wrong. >>>>> >>>>>> Added ramp-delay for LDO9(VDD33_USB3_0). >>>>>> Added ramp-delay for LDO13(VDDQ_MMC2). >>>>>> Added ramp-delay for LDO15(ETH_P3V3). >>>>>> >>>>>> Signed-off-by: Anand Moon <linux.amoon@gmail.com> >>>>>> >>>>>> --- >>>>>> Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch >>>>>> >>>>>> Note: >>>>>> Changes need for support of UHS-I highspeed cards. >>>>>> changes for vqmmc-supply for emmc is not supported. >>>>>> >>>>>> [ 1.831136] vdd_ldo9: ramp_delay not set >>>>>> [ 1.843049] vdd_ldo13: ramp_delay not set >>>>>> [ 1.850975] vdd_ldo15: ramp_delay not set >>>>>> [ 1.862816] vdd_sd: ramp_delay not set >>>>>> --- >>>>>> arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 8 +++++++- >>>>>> 1 file changed, 7 insertions(+), 1 deletion(-) >>>>>> >>>>>> diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>>>> index 26decbd..58c06d3 100644 >>>>>> --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>>>> +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>>>> @@ -157,6 +157,7 @@ >>>>>> regulator-min-microvolt = <3000000>; >>>>>> regulator-max-microvolt = <3000000>; >>>>>> regulator-always-on; >>>>>> + regulator-ramp-delay = <12000>; >>>>>> }; >>>>>> >>>>>> ldo10_reg: LDO10 { >>>>>> @@ -182,9 +183,10 @@ >>>>>> >>>>>> ldo13_reg: LDO13 { >>>>>> regulator-name = "vdd_ldo13"; >>>>>> - regulator-min-microvolt = <2800000>; >>>>>> + regulator-min-microvolt = <1800000>; >>>>>> regulator-max-microvolt = <2800000>; >>>>>> regulator-always-on; >>>>>> + regulator-ramp-delay = <12000>; >>>>>> }; >>>>>> >>>>>> ldo15_reg: LDO15 { >>>>>> @@ -213,6 +215,7 @@ >>>>>> regulator-min-microvolt = <2800000>; >>>>>> regulator-max-microvolt = <2800000>; >>>>>> regulator-always-on; >>>>>> + regulator-ramp-delay = <12000>; >>>>> >>>>> Where did you get this value from? It looks wrong... My datasheet does >>>>> not have 12000 uV/uS. >>>> >>> >>>> Anand, >>>> >>>> We have actually been here: >>>> http://lists.infradead.org/pipermail/linux-arm-kernel/2015-June/351601.html >>>> >>>> That time you used 8000. I asked the same question - how did you figure >>>> out the exact value. >>>> >>>> Now we have the same question - why 12000? >>>> >>>> It is completely fine to make a mistake (I do a lot of them) but please >>>> try not to make the same mistake again. >>>> >>>> BR, >>>> Krzysztof >>> >>> I will focus more in the future to clamp down my mistakes to minimal. >>> >>>> >>>>> >>>>>> }; >>>>>> >>>>>> ldo24_reg: LDO24 { >>>>>> @@ -338,6 +341,7 @@ >>>>>> samsung,dw-mshc-ddr-timing = <0 2>; >>>>>> samsung,dw-mshc-hs400-timing = <0 2>; >>>>>> samsung,read-strobe-delay = <90>; >>>>>> + vmmc-supply = <&ldo3_reg>; >>>>>> pinctrl-names = "default"; >>>>>> pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8 &sd0_cd &sd0_rclk>; >>>>>> bus-width = <8>; >>>>>> @@ -352,6 +356,8 @@ >>>>>> samsung,dw-mshc-ciu-div = <3>; >>>>>> samsung,dw-mshc-sdr-timing = <0 4>; >>>>>> samsung,dw-mshc-ddr-timing = <0 2>; >>>>>> + vmmc-supply = <&ldo19_reg>; >>>>>> + vqmmc-supply = <&ldo13_reg>; >>>>> >>>>> It looks wrong. LDO13 is used in one place as VQMMC and in other as >>>>> VMMC. How did you figure out which regulator supplies which power domain? >>>>> >>> >>> I refer Schematics diagram to XU4_MAIN_REV0.1.pdf >>> >>> From the PWR_PMCI_S2MPS11_LDO_CTRL document it LDO13 point to VDDQ_MMC2. >>> >> >> Aaa right, by mistake I thought that you put LDO13 here and in the node >> before, but there is LDO3, not 13. You did this correctly. >> >> But I have two other questions: >> 1. Maybe these regulators now should not be always-enabled? > > regulator-always-on can be removed: I have tested this. > >> 2. Why changing minimum voltage of LDO13 to 1.8V? The schematics says 2.8V. >> > > In the schematics diagram to XU4_MAIN_REV0.1.pdf > >>From the EXYNOS5422 MMC UFS diagram CH2 range is VDDQ_MMC2 (1.8V/2.8V). Okay, so try to setting it to 1.8V (min and max) and see if it works correctly. On the same diagram few lines below: VDDQ_MMC2: 2.8V 250mA Best regards, Krzysztof ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 2/3] ARM: dts: use vmmc-supply of emmc/sd for exynos5422-odroidxu3 2015-10-13 0:10 ` Krzysztof Kozlowski @ 2015-10-13 2:29 ` Anand Moon 2015-10-13 2:39 ` Jaehoon Chung 0 siblings, 1 reply; 50+ messages in thread From: Anand Moon @ 2015-10-13 2:29 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Krzysztof Kozłowski, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung, devicetree, linux-arm-kernel, linux-samsung-soc@vger.kernel.org, Linux Kernel Hi Krzysztof, On 13 October 2015 at 05:40, Krzysztof Kozlowski <k.kozlowski@samsung.com> wrote: > On 12.10.2015 23:33, Anand Moon wrote: >> Hi Krzysztof, >> >> On 12 October 2015 at 17:43, Krzysztof Kozlowski >> <k.kozlowski@samsung.com> wrote: >>> W dniu 12.10.2015 o 20:08, Anand Moon pisze: >>>> Hi Krzysztof, >>>> >>>> On 12 October 2015 at 11:19, Krzysztof Kozlowski >>>> <k.kozlowski@samsung.com> wrote: >>>>> On 12.10.2015 13:42, Krzysztof Kozlowski wrote: >>>>>> On 12.10.2015 00:46, Anand Moon wrote: >>>>>>> Added support for vmmc/vqmmc-supply for emmc/sd cards. >>>>>>> Fixed the min values for regulator ldo13_reg (VDDQ_MMC2). >>>>>> >>>>>> I can't see the description of a problem which is fixed. If you fix >>>>>> something, then please describe what is wrong. >>>>>> >>>>>>> Added ramp-delay for LDO9(VDD33_USB3_0). >>>>>>> Added ramp-delay for LDO13(VDDQ_MMC2). >>>>>>> Added ramp-delay for LDO15(ETH_P3V3). >>>>>>> >>>>>>> Signed-off-by: Anand Moon <linux.amoon@gmail.com> >>>>>>> >>>>>>> --- >>>>>>> Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch >>>>>>> >>>>>>> Note: >>>>>>> Changes need for support of UHS-I highspeed cards. >>>>>>> changes for vqmmc-supply for emmc is not supported. >>>>>>> >>>>>>> [ 1.831136] vdd_ldo9: ramp_delay not set >>>>>>> [ 1.843049] vdd_ldo13: ramp_delay not set >>>>>>> [ 1.850975] vdd_ldo15: ramp_delay not set >>>>>>> [ 1.862816] vdd_sd: ramp_delay not set >>>>>>> --- >>>>>>> arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 8 +++++++- >>>>>>> 1 file changed, 7 insertions(+), 1 deletion(-) >>>>>>> >>>>>>> diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>>>>> index 26decbd..58c06d3 100644 >>>>>>> --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>>>>> +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>>>>> @@ -157,6 +157,7 @@ >>>>>>> regulator-min-microvolt = <3000000>; >>>>>>> regulator-max-microvolt = <3000000>; >>>>>>> regulator-always-on; >>>>>>> + regulator-ramp-delay = <12000>; >>>>>>> }; >>>>>>> >>>>>>> ldo10_reg: LDO10 { >>>>>>> @@ -182,9 +183,10 @@ >>>>>>> >>>>>>> ldo13_reg: LDO13 { >>>>>>> regulator-name = "vdd_ldo13"; >>>>>>> - regulator-min-microvolt = <2800000>; >>>>>>> + regulator-min-microvolt = <1800000>; >>>>>>> regulator-max-microvolt = <2800000>; >>>>>>> regulator-always-on; >>>>>>> + regulator-ramp-delay = <12000>; >>>>>>> }; >>>>>>> >>>>>>> ldo15_reg: LDO15 { >>>>>>> @@ -213,6 +215,7 @@ >>>>>>> regulator-min-microvolt = <2800000>; >>>>>>> regulator-max-microvolt = <2800000>; >>>>>>> regulator-always-on; >>>>>>> + regulator-ramp-delay = <12000>; >>>>>> >>>>>> Where did you get this value from? It looks wrong... My datasheet does >>>>>> not have 12000 uV/uS. >>>>> >>>> >>>>> Anand, >>>>> >>>>> We have actually been here: >>>>> http://lists.infradead.org/pipermail/linux-arm-kernel/2015-June/351601.html >>>>> >>>>> That time you used 8000. I asked the same question - how did you figure >>>>> out the exact value. >>>>> >>>>> Now we have the same question - why 12000? >>>>> >>>>> It is completely fine to make a mistake (I do a lot of them) but please >>>>> try not to make the same mistake again. >>>>> >>>>> BR, >>>>> Krzysztof >>>> >>>> I will focus more in the future to clamp down my mistakes to minimal. >>>> >>>>> >>>>>> >>>>>>> }; >>>>>>> >>>>>>> ldo24_reg: LDO24 { >>>>>>> @@ -338,6 +341,7 @@ >>>>>>> samsung,dw-mshc-ddr-timing = <0 2>; >>>>>>> samsung,dw-mshc-hs400-timing = <0 2>; >>>>>>> samsung,read-strobe-delay = <90>; >>>>>>> + vmmc-supply = <&ldo3_reg>; >>>>>>> pinctrl-names = "default"; >>>>>>> pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8 &sd0_cd &sd0_rclk>; >>>>>>> bus-width = <8>; >>>>>>> @@ -352,6 +356,8 @@ >>>>>>> samsung,dw-mshc-ciu-div = <3>; >>>>>>> samsung,dw-mshc-sdr-timing = <0 4>; >>>>>>> samsung,dw-mshc-ddr-timing = <0 2>; >>>>>>> + vmmc-supply = <&ldo19_reg>; >>>>>>> + vqmmc-supply = <&ldo13_reg>; >>>>>> >>>>>> It looks wrong. LDO13 is used in one place as VQMMC and in other as >>>>>> VMMC. How did you figure out which regulator supplies which power domain? >>>>>> >>>> >>>> I refer Schematics diagram to XU4_MAIN_REV0.1.pdf >>>> >>>> From the PWR_PMCI_S2MPS11_LDO_CTRL document it LDO13 point to VDDQ_MMC2. >>>> >>> >>> Aaa right, by mistake I thought that you put LDO13 here and in the node >>> before, but there is LDO3, not 13. You did this correctly. >>> >>> But I have two other questions: >>> 1. Maybe these regulators now should not be always-enabled? >> >> regulator-always-on can be removed: I have tested this. >> >>> 2. Why changing minimum voltage of LDO13 to 1.8V? The schematics says 2.8V. >>> >> >> In the schematics diagram to XU4_MAIN_REV0.1.pdf >> >>>From the EXYNOS5422 MMC UFS diagram CH2 range is VDDQ_MMC2 (1.8V/2.8V). > > Okay, so try to setting it to 1.8V (min and max) and see if it works > correctly. > > On the same diagram few lines below: > VDDQ_MMC2: 2.8V 250mA > You are correct. While working on this issue I tent to encounter make bugs. --------------------------------------------------------------------------------- [ 4.713553] random: nonblocking pool is initialized [ 4.718423] 14530000.hdmi supply hdmi-en not found, using dummy regulator [ 4.726206] exynos-drm exynos-drm: bound 14400000.fimd (ops fimd_component_ops) [ 4.732555] exynos-drm exynos-drm: bound 14450000.mixer (ops mixer_component_ops) [ 4.740180] exynos-drm exynos-drm: bound 14530000.hdmi (ops hdmi_component_ops) [ 4.746936] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 4.753428] [drm] No driver support for vblank timestamp query. [ 4.940794] Console: switching to colour frame buffer device 274x77 [ 4.995344] exynos-drm exynos-drm: fb0: frame buffer device [ 5.024573] [drm] Initialized exynos 1.0.0 20110530 on minor 0 [ 5.031164] exynos-dwc3 usb@12000000: no suspend clk specified [ 5.054571] usb 2-1: new full-speed USB device number 2 using exynos-ohci [ 5.159527] dwmmc_exynos 12220000.mmc: Busy; trying anyway [ 5.163705] mmc_host mmc1: Timeout sending command (cmd 0x202000 arg 0x0 status 0x0) --------------------------------------------------------------------------------- This is one bug. related to this changes. It stops booting waiting for the mmc1 card. -Anand Moon > Best regards, > Krzysztof ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 2/3] ARM: dts: use vmmc-supply of emmc/sd for exynos5422-odroidxu3 2015-10-13 2:29 ` Anand Moon @ 2015-10-13 2:39 ` Jaehoon Chung [not found] ` <561C6ED3.4090101-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> 0 siblings, 1 reply; 50+ messages in thread From: Jaehoon Chung @ 2015-10-13 2:39 UTC (permalink / raw) To: Anand Moon, Krzysztof Kozlowski Cc: Krzysztof Kozłowski, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, devicetree, linux-arm-kernel, linux-samsung-soc@vger.kernel.org, Linux Kernel On 10/13/2015 11:29 AM, Anand Moon wrote: > Hi Krzysztof, > > On 13 October 2015 at 05:40, Krzysztof Kozlowski > <k.kozlowski@samsung.com> wrote: >> On 12.10.2015 23:33, Anand Moon wrote: >>> Hi Krzysztof, >>> >>> On 12 October 2015 at 17:43, Krzysztof Kozlowski >>> <k.kozlowski@samsung.com> wrote: >>>> W dniu 12.10.2015 o 20:08, Anand Moon pisze: >>>>> Hi Krzysztof, >>>>> >>>>> On 12 October 2015 at 11:19, Krzysztof Kozlowski >>>>> <k.kozlowski@samsung.com> wrote: >>>>>> On 12.10.2015 13:42, Krzysztof Kozlowski wrote: >>>>>>> On 12.10.2015 00:46, Anand Moon wrote: >>>>>>>> Added support for vmmc/vqmmc-supply for emmc/sd cards. >>>>>>>> Fixed the min values for regulator ldo13_reg (VDDQ_MMC2). >>>>>>> >>>>>>> I can't see the description of a problem which is fixed. If you fix >>>>>>> something, then please describe what is wrong. >>>>>>> >>>>>>>> Added ramp-delay for LDO9(VDD33_USB3_0). >>>>>>>> Added ramp-delay for LDO13(VDDQ_MMC2). >>>>>>>> Added ramp-delay for LDO15(ETH_P3V3). >>>>>>>> >>>>>>>> Signed-off-by: Anand Moon <linux.amoon@gmail.com> >>>>>>>> >>>>>>>> --- >>>>>>>> Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch >>>>>>>> >>>>>>>> Note: >>>>>>>> Changes need for support of UHS-I highspeed cards. >>>>>>>> changes for vqmmc-supply for emmc is not supported. >>>>>>>> >>>>>>>> [ 1.831136] vdd_ldo9: ramp_delay not set >>>>>>>> [ 1.843049] vdd_ldo13: ramp_delay not set >>>>>>>> [ 1.850975] vdd_ldo15: ramp_delay not set >>>>>>>> [ 1.862816] vdd_sd: ramp_delay not set >>>>>>>> --- >>>>>>>> arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 8 +++++++- >>>>>>>> 1 file changed, 7 insertions(+), 1 deletion(-) >>>>>>>> >>>>>>>> diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>>>>>> index 26decbd..58c06d3 100644 >>>>>>>> --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>>>>>> +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>>>>>> @@ -157,6 +157,7 @@ >>>>>>>> regulator-min-microvolt = <3000000>; >>>>>>>> regulator-max-microvolt = <3000000>; >>>>>>>> regulator-always-on; >>>>>>>> + regulator-ramp-delay = <12000>; >>>>>>>> }; >>>>>>>> >>>>>>>> ldo10_reg: LDO10 { >>>>>>>> @@ -182,9 +183,10 @@ >>>>>>>> >>>>>>>> ldo13_reg: LDO13 { >>>>>>>> regulator-name = "vdd_ldo13"; >>>>>>>> - regulator-min-microvolt = <2800000>; >>>>>>>> + regulator-min-microvolt = <1800000>; >>>>>>>> regulator-max-microvolt = <2800000>; >>>>>>>> regulator-always-on; >>>>>>>> + regulator-ramp-delay = <12000>; >>>>>>>> }; >>>>>>>> >>>>>>>> ldo15_reg: LDO15 { >>>>>>>> @@ -213,6 +215,7 @@ >>>>>>>> regulator-min-microvolt = <2800000>; >>>>>>>> regulator-max-microvolt = <2800000>; >>>>>>>> regulator-always-on; >>>>>>>> + regulator-ramp-delay = <12000>; >>>>>>> >>>>>>> Where did you get this value from? It looks wrong... My datasheet does >>>>>>> not have 12000 uV/uS. >>>>>> >>>>> >>>>>> Anand, >>>>>> >>>>>> We have actually been here: >>>>>> http://lists.infradead.org/pipermail/linux-arm-kernel/2015-June/351601.html >>>>>> >>>>>> That time you used 8000. I asked the same question - how did you figure >>>>>> out the exact value. >>>>>> >>>>>> Now we have the same question - why 12000? >>>>>> >>>>>> It is completely fine to make a mistake (I do a lot of them) but please >>>>>> try not to make the same mistake again. >>>>>> >>>>>> BR, >>>>>> Krzysztof >>>>> >>>>> I will focus more in the future to clamp down my mistakes to minimal. >>>>> >>>>>> >>>>>>> >>>>>>>> }; >>>>>>>> >>>>>>>> ldo24_reg: LDO24 { >>>>>>>> @@ -338,6 +341,7 @@ >>>>>>>> samsung,dw-mshc-ddr-timing = <0 2>; >>>>>>>> samsung,dw-mshc-hs400-timing = <0 2>; >>>>>>>> samsung,read-strobe-delay = <90>; >>>>>>>> + vmmc-supply = <&ldo3_reg>; >>>>>>>> pinctrl-names = "default"; >>>>>>>> pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8 &sd0_cd &sd0_rclk>; >>>>>>>> bus-width = <8>; >>>>>>>> @@ -352,6 +356,8 @@ >>>>>>>> samsung,dw-mshc-ciu-div = <3>; >>>>>>>> samsung,dw-mshc-sdr-timing = <0 4>; >>>>>>>> samsung,dw-mshc-ddr-timing = <0 2>; >>>>>>>> + vmmc-supply = <&ldo19_reg>; >>>>>>>> + vqmmc-supply = <&ldo13_reg>; >>>>>>> >>>>>>> It looks wrong. LDO13 is used in one place as VQMMC and in other as >>>>>>> VMMC. How did you figure out which regulator supplies which power domain? >>>>>>> >>>>> >>>>> I refer Schematics diagram to XU4_MAIN_REV0.1.pdf >>>>> >>>>> From the PWR_PMCI_S2MPS11_LDO_CTRL document it LDO13 point to VDDQ_MMC2. >>>>> >>>> >>>> Aaa right, by mistake I thought that you put LDO13 here and in the node >>>> before, but there is LDO3, not 13. You did this correctly. >>>> >>>> But I have two other questions: >>>> 1. Maybe these regulators now should not be always-enabled? >>> >>> regulator-always-on can be removed: I have tested this. >>> >>>> 2. Why changing minimum voltage of LDO13 to 1.8V? The schematics says 2.8V. >>>> >>> >>> In the schematics diagram to XU4_MAIN_REV0.1.pdf >>> >>> >From the EXYNOS5422 MMC UFS diagram CH2 range is VDDQ_MMC2 (1.8V/2.8V). >> >> Okay, so try to setting it to 1.8V (min and max) and see if it works >> correctly. >> >> On the same diagram few lines below: >> VDDQ_MMC2: 2.8V 250mA >> > > You are correct. > While working on this issue I tent to encounter make bugs. > --------------------------------------------------------------------------------- > [ 4.713553] random: nonblocking pool is initialized > [ 4.718423] 14530000.hdmi supply hdmi-en not found, using dummy regulator > [ 4.726206] exynos-drm exynos-drm: bound 14400000.fimd (ops > fimd_component_ops) > [ 4.732555] exynos-drm exynos-drm: bound 14450000.mixer (ops > mixer_component_ops) > [ 4.740180] exynos-drm exynos-drm: bound 14530000.hdmi (ops > hdmi_component_ops) > [ 4.746936] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). > [ 4.753428] [drm] No driver support for vblank timestamp query. > [ 4.940794] Console: switching to colour frame buffer device 274x77 > [ 4.995344] exynos-drm exynos-drm: fb0: frame buffer device > [ 5.024573] [drm] Initialized exynos 1.0.0 20110530 on minor 0 > [ 5.031164] exynos-dwc3 usb@12000000: no suspend clk specified > [ 5.054571] usb 2-1: new full-speed USB device number 2 using exynos-ohci > [ 5.159527] dwmmc_exynos 12220000.mmc: Busy; trying anyway > [ 5.163705] mmc_host mmc1: Timeout sending command (cmd 0x202000 > arg 0x0 status 0x0) > --------------------------------------------------------------------------------- > This is one bug. related to this changes. It stops booting waiting for > the mmc1 card. It seems that it failed to switch voltage. Best Regards, Jaehoon Chung > > -Anand Moon > >> Best regards, >> Krzysztof > ^ permalink raw reply [flat|nested] 50+ messages in thread
[parent not found: <561C6ED3.4090101-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>]
* Re: [PATCH 2/3] ARM: dts: use vmmc-supply of emmc/sd for exynos5422-odroidxu3 [not found] ` <561C6ED3.4090101-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> @ 2015-10-13 2:45 ` Anand Moon 0 siblings, 0 replies; 50+ messages in thread From: Anand Moon @ 2015-10-13 2:45 UTC (permalink / raw) To: Jaehoon Chung Cc: Krzysztof Kozlowski, Krzysztof Kozłowski, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-samsung-soc-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, Linux Kernel Hi Jaehoon Chung, On 13 October 2015 at 08:09, Jaehoon Chung <jh80.chung-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> wrote: > On 10/13/2015 11:29 AM, Anand Moon wrote: >> Hi Krzysztof, >> >> On 13 October 2015 at 05:40, Krzysztof Kozlowski >> <k.kozlowski-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> wrote: >>> On 12.10.2015 23:33, Anand Moon wrote: >>>> Hi Krzysztof, >>>> >>>> On 12 October 2015 at 17:43, Krzysztof Kozlowski >>>> <k.kozlowski-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> wrote: >>>>> W dniu 12.10.2015 o 20:08, Anand Moon pisze: >>>>>> Hi Krzysztof, >>>>>> >>>>>> On 12 October 2015 at 11:19, Krzysztof Kozlowski >>>>>> <k.kozlowski-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> wrote: >>>>>>> On 12.10.2015 13:42, Krzysztof Kozlowski wrote: >>>>>>>> On 12.10.2015 00:46, Anand Moon wrote: >>>>>>>>> Added support for vmmc/vqmmc-supply for emmc/sd cards. >>>>>>>>> Fixed the min values for regulator ldo13_reg (VDDQ_MMC2). >>>>>>>> >>>>>>>> I can't see the description of a problem which is fixed. If you fix >>>>>>>> something, then please describe what is wrong. >>>>>>>> >>>>>>>>> Added ramp-delay for LDO9(VDD33_USB3_0). >>>>>>>>> Added ramp-delay for LDO13(VDDQ_MMC2). >>>>>>>>> Added ramp-delay for LDO15(ETH_P3V3). >>>>>>>>> >>>>>>>>> Signed-off-by: Anand Moon <linux.amoon-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> >>>>>>>>> >>>>>>>>> --- >>>>>>>>> Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch >>>>>>>>> >>>>>>>>> Note: >>>>>>>>> Changes need for support of UHS-I highspeed cards. >>>>>>>>> changes for vqmmc-supply for emmc is not supported. >>>>>>>>> >>>>>>>>> [ 1.831136] vdd_ldo9: ramp_delay not set >>>>>>>>> [ 1.843049] vdd_ldo13: ramp_delay not set >>>>>>>>> [ 1.850975] vdd_ldo15: ramp_delay not set >>>>>>>>> [ 1.862816] vdd_sd: ramp_delay not set >>>>>>>>> --- >>>>>>>>> arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 8 +++++++- >>>>>>>>> 1 file changed, 7 insertions(+), 1 deletion(-) >>>>>>>>> >>>>>>>>> diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>>>>>>> index 26decbd..58c06d3 100644 >>>>>>>>> --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>>>>>>> +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>>>>>>> @@ -157,6 +157,7 @@ >>>>>>>>> regulator-min-microvolt = <3000000>; >>>>>>>>> regulator-max-microvolt = <3000000>; >>>>>>>>> regulator-always-on; >>>>>>>>> + regulator-ramp-delay = <12000>; >>>>>>>>> }; >>>>>>>>> >>>>>>>>> ldo10_reg: LDO10 { >>>>>>>>> @@ -182,9 +183,10 @@ >>>>>>>>> >>>>>>>>> ldo13_reg: LDO13 { >>>>>>>>> regulator-name = "vdd_ldo13"; >>>>>>>>> - regulator-min-microvolt = <2800000>; >>>>>>>>> + regulator-min-microvolt = <1800000>; >>>>>>>>> regulator-max-microvolt = <2800000>; >>>>>>>>> regulator-always-on; >>>>>>>>> + regulator-ramp-delay = <12000>; >>>>>>>>> }; >>>>>>>>> >>>>>>>>> ldo15_reg: LDO15 { >>>>>>>>> @@ -213,6 +215,7 @@ >>>>>>>>> regulator-min-microvolt = <2800000>; >>>>>>>>> regulator-max-microvolt = <2800000>; >>>>>>>>> regulator-always-on; >>>>>>>>> + regulator-ramp-delay = <12000>; >>>>>>>> >>>>>>>> Where did you get this value from? It looks wrong... My datasheet does >>>>>>>> not have 12000 uV/uS. >>>>>>> >>>>>> >>>>>>> Anand, >>>>>>> >>>>>>> We have actually been here: >>>>>>> http://lists.infradead.org/pipermail/linux-arm-kernel/2015-June/351601.html >>>>>>> >>>>>>> That time you used 8000. I asked the same question - how did you figure >>>>>>> out the exact value. >>>>>>> >>>>>>> Now we have the same question - why 12000? >>>>>>> >>>>>>> It is completely fine to make a mistake (I do a lot of them) but please >>>>>>> try not to make the same mistake again. >>>>>>> >>>>>>> BR, >>>>>>> Krzysztof >>>>>> >>>>>> I will focus more in the future to clamp down my mistakes to minimal. >>>>>> >>>>>>> >>>>>>>> >>>>>>>>> }; >>>>>>>>> >>>>>>>>> ldo24_reg: LDO24 { >>>>>>>>> @@ -338,6 +341,7 @@ >>>>>>>>> samsung,dw-mshc-ddr-timing = <0 2>; >>>>>>>>> samsung,dw-mshc-hs400-timing = <0 2>; >>>>>>>>> samsung,read-strobe-delay = <90>; >>>>>>>>> + vmmc-supply = <&ldo3_reg>; >>>>>>>>> pinctrl-names = "default"; >>>>>>>>> pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8 &sd0_cd &sd0_rclk>; >>>>>>>>> bus-width = <8>; >>>>>>>>> @@ -352,6 +356,8 @@ >>>>>>>>> samsung,dw-mshc-ciu-div = <3>; >>>>>>>>> samsung,dw-mshc-sdr-timing = <0 4>; >>>>>>>>> samsung,dw-mshc-ddr-timing = <0 2>; >>>>>>>>> + vmmc-supply = <&ldo19_reg>; >>>>>>>>> + vqmmc-supply = <&ldo13_reg>; >>>>>>>> >>>>>>>> It looks wrong. LDO13 is used in one place as VQMMC and in other as >>>>>>>> VMMC. How did you figure out which regulator supplies which power domain? >>>>>>>> >>>>>> >>>>>> I refer Schematics diagram to XU4_MAIN_REV0.1.pdf >>>>>> >>>>>> From the PWR_PMCI_S2MPS11_LDO_CTRL document it LDO13 point to VDDQ_MMC2. >>>>>> >>>>> >>>>> Aaa right, by mistake I thought that you put LDO13 here and in the node >>>>> before, but there is LDO3, not 13. You did this correctly. >>>>> >>>>> But I have two other questions: >>>>> 1. Maybe these regulators now should not be always-enabled? >>>> >>>> regulator-always-on can be removed: I have tested this. >>>> >>>>> 2. Why changing minimum voltage of LDO13 to 1.8V? The schematics says 2.8V. >>>>> >>>> >>>> In the schematics diagram to XU4_MAIN_REV0.1.pdf >>>> >>>> >From the EXYNOS5422 MMC UFS diagram CH2 range is VDDQ_MMC2 (1.8V/2.8V). >>> >>> Okay, so try to setting it to 1.8V (min and max) and see if it works >>> correctly. >>> >>> On the same diagram few lines below: >>> VDDQ_MMC2: 2.8V 250mA >>> >> >> You are correct. >> While working on this issue I tent to encounter make bugs. >> --------------------------------------------------------------------------------- >> [ 4.713553] random: nonblocking pool is initialized >> [ 4.718423] 14530000.hdmi supply hdmi-en not found, using dummy regulator >> [ 4.726206] exynos-drm exynos-drm: bound 14400000.fimd (ops >> fimd_component_ops) >> [ 4.732555] exynos-drm exynos-drm: bound 14450000.mixer (ops >> mixer_component_ops) >> [ 4.740180] exynos-drm exynos-drm: bound 14530000.hdmi (ops >> hdmi_component_ops) >> [ 4.746936] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). >> [ 4.753428] [drm] No driver support for vblank timestamp query. >> [ 4.940794] Console: switching to colour frame buffer device 274x77 >> [ 4.995344] exynos-drm exynos-drm: fb0: frame buffer device >> [ 5.024573] [drm] Initialized exynos 1.0.0 20110530 on minor 0 >> [ 5.031164] exynos-dwc3 usb@12000000: no suspend clk specified >> [ 5.054571] usb 2-1: new full-speed USB device number 2 using exynos-ohci >> [ 5.159527] dwmmc_exynos 12220000.mmc: Busy; trying anyway >> [ 5.163705] mmc_host mmc1: Timeout sending command (cmd 0x202000 >> arg 0x0 status 0x0) >> --------------------------------------------------------------------------------- >> This is one bug. related to this changes. It stops booting waiting for >> the mmc1 card. > > It seems that it failed to switch voltage. > > Best Regards, > Jaehoon Chung > You are correct. This happens when the min/max value for ldo13_reg is 2.8V. -Anand Moon >> >> -Anand Moon >> >>> Best regards, >>> Krzysztof >> > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 50+ messages in thread
* [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support 2015-10-11 15:46 [PATCH 1/3] ARM: dts: exynos5422-odroidxu3: use cd-gpio method to detect sd-card Anand Moon 2015-10-11 15:46 ` [PATCH 2/3] ARM: dts: use vmmc-supply of emmc/sd for exynos5422-odroidxu3 Anand Moon @ 2015-10-11 15:46 ` Anand Moon [not found] ` <1444578364-1384-3-git-send-email-linux.amoon-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> 2015-10-12 4:29 ` [PATCH 1/3] ARM: dts: exynos5422-odroidxu3: use cd-gpio method to detect sd-card Krzysztof Kozlowski 2 siblings, 1 reply; 50+ messages in thread From: Anand Moon @ 2015-10-11 15:46 UTC (permalink / raw) To: Kukjin Kim, Krzysztof Kozlowski, Javier Martinez Canillas, Anand Moon, Lukasz Majewski, Jaehoon Chung Cc: devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel Added support for UHS-I bus speed 50MB/s (SDR50, DDR50) 104MB/s (SDR104) Signed-off-by: Anand Moon <linux.amoon@gmail.com> --- Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch Changes Fixed the UHS-I bus speed detedtion on cold boot. [ 2.439806] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 100000000Hz, actual 100000000HZ div = 0) [ 2.449729] mmc1: new ultra high speed SDR50 SDHC card at address aaaa [ 2.455984] mmcblk0: mmc1:aaaa SL32G 29.7 GiB [ 2.461743] mmcblk0: p1 p2 --- arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi index 58c06d3..ba4a87b 100644 --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi @@ -364,6 +364,10 @@ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; bus-width = <4>; cap-sd-highspeed; + sd-uhs-sdr12; + sd-uhs-sdr25; + sd-uhs-sdr50; + sd-uhs-sdr104; }; &pinctrl_0 { -- 2.1.4 ^ permalink raw reply related [flat|nested] 50+ messages in thread
[parent not found: <1444578364-1384-3-git-send-email-linux.amoon-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>]
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support [not found] ` <1444578364-1384-3-git-send-email-linux.amoon-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> @ 2015-10-12 5:44 ` Krzysztof Kozlowski 2015-10-12 10:46 ` Anand Moon 2015-10-12 15:32 ` Anand Moon 0 siblings, 2 replies; 50+ messages in thread From: Krzysztof Kozlowski @ 2015-10-12 5:44 UTC (permalink / raw) To: Anand Moon, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-samsung-soc-u79uwXL29TY76Z2rM5mHXA, linux-kernel-u79uwXL29TY76Z2rM5mHXA On 12.10.2015 00:46, Anand Moon wrote: > Added support for UHS-I bus speed 50MB/s (SDR50, DDR50) 104MB/s (SDR104) This description is not entirely correct. The MMC driver already supports these UHS speeds (you did not any code) so you rather enabled it (description of bindings says "is supported"). You mentioned DDR50 but I don't see respective property below. How do you know that these modes are really supported? I don't know. Can you convince me? > > Signed-off-by: Anand Moon <linux.amoon-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> > > --- > Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch > > Changes Fixed the UHS-I bus speed detedtion on cold boot. I don't get what is exactly fixed here. What was the error? What is the outcome of this fix? The log below is before or after? Best regards, Krzysztof > > [ 2.439806] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 100000000Hz, actual 100000000HZ div = 0) > [ 2.449729] mmc1: new ultra high speed SDR50 SDHC card at address aaaa > [ 2.455984] mmcblk0: mmc1:aaaa SL32G 29.7 GiB > [ 2.461743] mmcblk0: p1 p2 > --- > arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 4 ++++ > 1 file changed, 4 insertions(+) > > diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi > index 58c06d3..ba4a87b 100644 > --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi > +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi > @@ -364,6 +364,10 @@ > pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; > bus-width = <4>; > cap-sd-highspeed; > + sd-uhs-sdr12; > + sd-uhs-sdr25; > + sd-uhs-sdr50; > + sd-uhs-sdr104; > }; > > &pinctrl_0 { > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support 2015-10-12 5:44 ` Krzysztof Kozlowski @ 2015-10-12 10:46 ` Anand Moon 2015-10-12 10:51 ` Jaehoon Chung 2015-10-12 12:42 ` Krzysztof Kozlowski 2015-10-12 15:32 ` Anand Moon 1 sibling, 2 replies; 50+ messages in thread From: Anand Moon @ 2015-10-12 10:46 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung, devicetree, linux-arm-kernel, linux-samsung-soc@vger.kernel.org, Linux Kernel Hi Krzysztof, On 12 October 2015 at 11:14, Krzysztof Kozlowski <k.kozlowski@samsung.com> wrote: > On 12.10.2015 00:46, Anand Moon wrote: >> Added support for UHS-I bus speed 50MB/s (SDR50, DDR50) 104MB/s (SDR104) > > This description is not entirely correct. The MMC driver already > supports these UHS speeds (you did not any code) so you rather enabled > it (description of bindings says "is supported"). > > You mentioned DDR50 but I don't see respective property below. Looks like I missed it, I will add this in the next patch, > > How do you know that these modes are really supported? I don't know. Can > you convince me? > >> >> Signed-off-by: Anand Moon <linux.amoon@gmail.com> >> >> --- >> Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch >> >> Changes Fixed the UHS-I bus speed detedtion on cold boot. > > I don't get what is exactly fixed here. What was the error? What is the > outcome of this fix? The log below is before or after? > > Best regards, > Krzysztof > >> >> [ 2.439806] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 100000000Hz, actual 100000000HZ div = 0) >> [ 2.449729] mmc1: new ultra high speed SDR50 SDHC card at address aaaa >> [ 2.455984] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >> [ 2.461743] mmcblk0: p1 p2 > >> --- >> arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 4 ++++ >> 1 file changed, 4 insertions(+) >> >> diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >> index 58c06d3..ba4a87b 100644 >> --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >> +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >> @@ -364,6 +364,10 @@ >> pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; >> bus-width = <4>; >> cap-sd-highspeed; >> + sd-uhs-sdr12; >> + sd-uhs-sdr25; >> + sd-uhs-sdr50; >> + sd-uhs-sdr104; >> }; >> >> &pinctrl_0 { >> > Changes were made to support Sandisk Ultra UHS-I class 10 card support. OdroidXU3/XU4 board would not boot up using this card. Depending on the capability of the UHS-I card, the speed of the card is selected. I have just added the enhance capability feature to support them. On warm boot: i.e reboot of the board. [ 4.649073] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 4.657555] mmc1: new high speed SDHC card at address aaaa [ 4.663787] mmcblk0: mmc1:aaaa SL32G 29.7 GiB [ 4.669206] mmcblk0: p1 p2 On cold boot:: ie: power on the board. [ 4.630237] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 100000000Hz, actual 100000000HZ div = 0) [ 4.639820] mmc1: new ultra high speed SDR50 SDHC card at address aaaa [ 4.646266] mmcblk0: mmc1:aaaa SL32G 29.7 GiB [ 4.650293] IRQ56 no longer affine to CPU7 [ 4.650581] CPU7: shutdown [ 4.658293] mmcblk0: p1 p2 Note: Their is need to reset the PMIC S2MPS11_REG_L13CTRL/S2MPS11_REG_L19CTRL registers to support this feature consistently on every reboot. -Anand Moon ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support 2015-10-12 10:46 ` Anand Moon @ 2015-10-12 10:51 ` Jaehoon Chung 2015-10-12 11:23 ` Anand Moon 2015-10-12 12:42 ` Krzysztof Kozlowski 1 sibling, 1 reply; 50+ messages in thread From: Jaehoon Chung @ 2015-10-12 10:51 UTC (permalink / raw) To: Anand Moon, Krzysztof Kozlowski Cc: Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, devicetree, linux-arm-kernel, linux-samsung-soc@vger.kernel.org, Linux Kernel On 10/12/2015 07:46 PM, Anand Moon wrote: > Hi Krzysztof, > > On 12 October 2015 at 11:14, Krzysztof Kozlowski > <k.kozlowski@samsung.com> wrote: >> On 12.10.2015 00:46, Anand Moon wrote: >>> Added support for UHS-I bus speed 50MB/s (SDR50, DDR50) 104MB/s (SDR104) >> >> This description is not entirely correct. The MMC driver already >> supports these UHS speeds (you did not any code) so you rather enabled >> it (description of bindings says "is supported"). >> >> You mentioned DDR50 but I don't see respective property below. > Looks like I missed it, I will add this in the next patch, >> >> How do you know that these modes are really supported? I don't know. Can >> you convince me? >> > >>> >>> Signed-off-by: Anand Moon <linux.amoon@gmail.com> >>> >>> --- >>> Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch >>> >>> Changes Fixed the UHS-I bus speed detedtion on cold boot. >> >> I don't get what is exactly fixed here. What was the error? What is the >> outcome of this fix? The log below is before or after? >> >> Best regards, >> Krzysztof >> >>> >>> [ 2.439806] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 100000000Hz, actual 100000000HZ div = 0) >>> [ 2.449729] mmc1: new ultra high speed SDR50 SDHC card at address aaaa >>> [ 2.455984] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >>> [ 2.461743] mmcblk0: p1 p2 >> >>> --- >>> arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 4 ++++ >>> 1 file changed, 4 insertions(+) >>> >>> diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>> index 58c06d3..ba4a87b 100644 >>> --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>> +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>> @@ -364,6 +364,10 @@ >>> pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; >>> bus-width = <4>; >>> cap-sd-highspeed; >>> + sd-uhs-sdr12; >>> + sd-uhs-sdr25; >>> + sd-uhs-sdr50; >>> + sd-uhs-sdr104; >>> }; >>> >>> &pinctrl_0 { >>> >> > > Changes were made to support Sandisk Ultra UHS-I class 10 card support. > OdroidXU3/XU4 board would not boot up using this card. > > Depending on the capability of the UHS-I card, the speed of the card > is selected. > I have just added the enhance capability feature to support them. > > On warm boot: i.e reboot of the board. > [ 4.649073] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot > req 50000000Hz, actual 50000000HZ div = 0) > [ 4.657555] mmc1: new high speed SDHC card at address aaaa > [ 4.663787] mmcblk0: mmc1:aaaa SL32G 29.7 GiB > [ 4.669206] mmcblk0: p1 p2 > > On cold boot:: ie: power on the board. > > [ 4.630237] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot > req 100000000Hz, actual 100000000HZ div = 0) > [ 4.639820] mmc1: new ultra high speed SDR50 SDHC card at address aaaa > [ 4.646266] mmcblk0: mmc1:aaaa SL32G 29.7 GiB > [ 4.650293] IRQ56 no longer affine to CPU7 > [ 4.650581] CPU7: shutdown > [ 4.658293] mmcblk0: p1 p2 > > Note: Their is need to reset the PMIC > S2MPS11_REG_L13CTRL/S2MPS11_REG_L19CTRL registers > to support this feature consistently on every reboot. I don't understand...why needs to reset? I know it needs to switch the voltage, doesn't it? Best Regards, Jaehoon Chung > > -Anand Moon > ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support 2015-10-12 10:51 ` Jaehoon Chung @ 2015-10-12 11:23 ` Anand Moon 0 siblings, 0 replies; 50+ messages in thread From: Anand Moon @ 2015-10-12 11:23 UTC (permalink / raw) To: Jaehoon Chung Cc: Krzysztof Kozlowski, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, devicetree, linux-arm-kernel, linux-samsung-soc@vger.kernel.org, Linux Kernel Hi Jaehoon Chung On 12 October 2015 at 16:21, Jaehoon Chung <jh80.chung@samsung.com> wrote: > On 10/12/2015 07:46 PM, Anand Moon wrote: >> Hi Krzysztof, >> >> On 12 October 2015 at 11:14, Krzysztof Kozlowski >> <k.kozlowski@samsung.com> wrote: >>> On 12.10.2015 00:46, Anand Moon wrote: >>>> Added support for UHS-I bus speed 50MB/s (SDR50, DDR50) 104MB/s (SDR104) >>> >>> This description is not entirely correct. The MMC driver already >>> supports these UHS speeds (you did not any code) so you rather enabled >>> it (description of bindings says "is supported"). >>> >>> You mentioned DDR50 but I don't see respective property below. >> Looks like I missed it, I will add this in the next patch, >>> >>> How do you know that these modes are really supported? I don't know. Can >>> you convince me? >>> >> >>>> >>>> Signed-off-by: Anand Moon <linux.amoon@gmail.com> >>>> >>>> --- >>>> Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch >>>> >>>> Changes Fixed the UHS-I bus speed detedtion on cold boot. >>> >>> I don't get what is exactly fixed here. What was the error? What is the >>> outcome of this fix? The log below is before or after? >>> >>> Best regards, >>> Krzysztof >>> >>>> >>>> [ 2.439806] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 100000000Hz, actual 100000000HZ div = 0) >>>> [ 2.449729] mmc1: new ultra high speed SDR50 SDHC card at address aaaa >>>> [ 2.455984] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >>>> [ 2.461743] mmcblk0: p1 p2 >>> >>>> --- >>>> arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 4 ++++ >>>> 1 file changed, 4 insertions(+) >>>> >>>> diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>> index 58c06d3..ba4a87b 100644 >>>> --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>> +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>> @@ -364,6 +364,10 @@ >>>> pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; >>>> bus-width = <4>; >>>> cap-sd-highspeed; >>>> + sd-uhs-sdr12; >>>> + sd-uhs-sdr25; >>>> + sd-uhs-sdr50; >>>> + sd-uhs-sdr104; >>>> }; >>>> >>>> &pinctrl_0 { >>>> >>> >> >> Changes were made to support Sandisk Ultra UHS-I class 10 card support. >> OdroidXU3/XU4 board would not boot up using this card. >> >> Depending on the capability of the UHS-I card, the speed of the card >> is selected. >> I have just added the enhance capability feature to support them. >> >> On warm boot: i.e reboot of the board. >> [ 4.649073] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot >> req 50000000Hz, actual 50000000HZ div = 0) >> [ 4.657555] mmc1: new high speed SDHC card at address aaaa >> [ 4.663787] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >> [ 4.669206] mmcblk0: p1 p2 >> >> On cold boot:: ie: power on the board. >> >> [ 4.630237] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot >> req 100000000Hz, actual 100000000HZ div = 0) >> [ 4.639820] mmc1: new ultra high speed SDR50 SDHC card at address aaaa >> [ 4.646266] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >> [ 4.650293] IRQ56 no longer affine to CPU7 >> [ 4.650581] CPU7: shutdown >> [ 4.658293] mmcblk0: p1 p2 >> >> Note: Their is need to reset the PMIC >> S2MPS11_REG_L13CTRL/S2MPS11_REG_L19CTRL registers >> to support this feature consistently on every reboot. > > I don't understand...why needs to reset? > I know it needs to switch the voltage, doesn't it? > I was referring to this code. https://github.com/hardkernel/linux/blob/odroidxu3-3.10.y/drivers/regulator/s2mps11.c#L451 I am not sure if this need to fixed in u-boot of hardkernel or shutdown function. -Anand Moon > Best Regards, > Jaehoon Chung > >> >> -Anand Moon >> > ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support 2015-10-12 10:46 ` Anand Moon 2015-10-12 10:51 ` Jaehoon Chung @ 2015-10-12 12:42 ` Krzysztof Kozlowski 2015-10-12 13:04 ` Jaehoon Chung 1 sibling, 1 reply; 50+ messages in thread From: Krzysztof Kozlowski @ 2015-10-12 12:42 UTC (permalink / raw) To: Anand Moon Cc: k.kozlowski.k, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung, devicetree, linux-arm-kernel, linux-samsung-soc@vger.kernel.org, Linux Kernel W dniu 12.10.2015 o 19:46, Anand Moon pisze: > Hi Krzysztof, > > On 12 October 2015 at 11:14, Krzysztof Kozlowski > <k.kozlowski@samsung.com> wrote: >> On 12.10.2015 00:46, Anand Moon wrote: >>> Added support for UHS-I bus speed 50MB/s (SDR50, DDR50) 104MB/s (SDR104) >> >> This description is not entirely correct. The MMC driver already >> supports these UHS speeds (you did not any code) so you rather enabled >> it (description of bindings says "is supported"). >> >> You mentioned DDR50 but I don't see respective property below. > Looks like I missed it, I will add this in the next patch, >> >> How do you know that these modes are really supported? I don't know. Can >> you convince me? That part was not answered... >> > >>> >>> Signed-off-by: Anand Moon <linux.amoon@gmail.com> >>> >>> --- >>> Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch >>> >>> Changes Fixed the UHS-I bus speed detedtion on cold boot. >> >> I don't get what is exactly fixed here. What was the error? What is the >> outcome of this fix? The log below is before or after? >> >> Best regards, >> Krzysztof >> >>> >>> [ 2.439806] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 100000000Hz, actual 100000000HZ div = 0) >>> [ 2.449729] mmc1: new ultra high speed SDR50 SDHC card at address aaaa >>> [ 2.455984] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >>> [ 2.461743] mmcblk0: p1 p2 >> >>> --- >>> arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 4 ++++ >>> 1 file changed, 4 insertions(+) >>> >>> diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>> index 58c06d3..ba4a87b 100644 >>> --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>> +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>> @@ -364,6 +364,10 @@ >>> pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; >>> bus-width = <4>; >>> cap-sd-highspeed; >>> + sd-uhs-sdr12; >>> + sd-uhs-sdr25; >>> + sd-uhs-sdr50; >>> + sd-uhs-sdr104; >>> }; >>> >>> &pinctrl_0 { >>> >> > > Changes were made to support Sandisk Ultra UHS-I class 10 card support. > OdroidXU3/XU4 board would not boot up using this card. > > Depending on the capability of the UHS-I card, the speed of the card > is selected. > I have just added the enhance capability feature to support them. So without these capabilities mentioned microSD card cannot be used? So I have a UHS-I card, that one exactly: http://www.samsung.com/us/support/owners/product/MB-MP32D/APC It works: [ 2.628365] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 2.693296] mmc1: new high speed SDHC card at address 0001 [ 2.703867] mmcblk0: mmc1:0001 00000 29.8 GiB [ 2.708406] mmcblk0: p1 p2 This is just HS mode. In the same time isn't UHS-I backward compatible? Your report seems surprising. Best regards, Krzysztof > > On warm boot: i.e reboot of the board. > [ 4.649073] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot > req 50000000Hz, actual 50000000HZ div = 0) > [ 4.657555] mmc1: new high speed SDHC card at address aaaa > [ 4.663787] mmcblk0: mmc1:aaaa SL32G 29.7 GiB > [ 4.669206] mmcblk0: p1 p2 > > On cold boot:: ie: power on the board. > > [ 4.630237] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot > req 100000000Hz, actual 100000000HZ div = 0) > [ 4.639820] mmc1: new ultra high speed SDR50 SDHC card at address aaaa > [ 4.646266] mmcblk0: mmc1:aaaa SL32G 29.7 GiB > [ 4.650293] IRQ56 no longer affine to CPU7 > [ 4.650581] CPU7: shutdown > [ 4.658293] mmcblk0: p1 p2 > > Note: Their is need to reset the PMIC > S2MPS11_REG_L13CTRL/S2MPS11_REG_L19CTRL registers > to support this feature consistently on every reboot. > > -Anand Moon > -- > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > Please read the FAQ at http://www.tux.org/lkml/ > ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support 2015-10-12 12:42 ` Krzysztof Kozlowski @ 2015-10-12 13:04 ` Jaehoon Chung 2015-10-12 13:16 ` Krzysztof Kozlowski 0 siblings, 1 reply; 50+ messages in thread From: Jaehoon Chung @ 2015-10-12 13:04 UTC (permalink / raw) To: Krzysztof Kozlowski, Anand Moon Cc: k.kozlowski.k, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, devicetree, linux-arm-kernel, linux-samsung-soc@vger.kernel.org, Linux Kernel On 10/12/2015 09:42 PM, Krzysztof Kozlowski wrote: > W dniu 12.10.2015 o 19:46, Anand Moon pisze: >> Hi Krzysztof, >> >> On 12 October 2015 at 11:14, Krzysztof Kozlowski >> <k.kozlowski@samsung.com> wrote: >>> On 12.10.2015 00:46, Anand Moon wrote: >>>> Added support for UHS-I bus speed 50MB/s (SDR50, DDR50) 104MB/s (SDR104) >>> >>> This description is not entirely correct. The MMC driver already >>> supports these UHS speeds (you did not any code) so you rather enabled >>> it (description of bindings says "is supported"). >>> >>> You mentioned DDR50 but I don't see respective property below. >> Looks like I missed it, I will add this in the next patch, >>> >>> How do you know that these modes are really supported? I don't know. Can >>> you convince me? > > That part was not answered... In my experiment, it needs two requirements. One is that Host controller supported UHS-I mode or others, other is SD-card. In Anand's commit message, there is no information for this. And 50MB/s or 104MB/s is not real performance. (Just theoretical values) It seems that can get those performances. > >>> >> >>>> >>>> Signed-off-by: Anand Moon <linux.amoon@gmail.com> >>>> >>>> --- >>>> Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch >>>> >>>> Changes Fixed the UHS-I bus speed detedtion on cold boot. >>> >>> I don't get what is exactly fixed here. What was the error? What is the >>> outcome of this fix? The log below is before or after? >>> >>> Best regards, >>> Krzysztof >>> >>>> >>>> [ 2.439806] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 100000000Hz, actual 100000000HZ div = 0) >>>> [ 2.449729] mmc1: new ultra high speed SDR50 SDHC card at address aaaa >>>> [ 2.455984] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >>>> [ 2.461743] mmcblk0: p1 p2 >>> >>>> --- >>>> arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 4 ++++ >>>> 1 file changed, 4 insertions(+) >>>> >>>> diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>> index 58c06d3..ba4a87b 100644 >>>> --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>> +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>> @@ -364,6 +364,10 @@ >>>> pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; >>>> bus-width = <4>; >>>> cap-sd-highspeed; >>>> + sd-uhs-sdr12; >>>> + sd-uhs-sdr25; >>>> + sd-uhs-sdr50; >>>> + sd-uhs-sdr104; >>>> }; >>>> >>>> &pinctrl_0 { >>>> >>> >> >> Changes were made to support Sandisk Ultra UHS-I class 10 card support. >> OdroidXU3/XU4 board would not boot up using this card. >> >> Depending on the capability of the UHS-I card, the speed of the card >> is selected. >> I have just added the enhance capability feature to support them. > > So without these capabilities mentioned microSD card cannot be used? So > I have a UHS-I card, that one exactly: > http://www.samsung.com/us/support/owners/product/MB-MP32D/APC > > It works: > [ 2.628365] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req > 50000000Hz, actual 50000000HZ div = 0) > [ 2.693296] mmc1: new high speed SDHC card at address 0001 > [ 2.703867] mmcblk0: mmc1:0001 00000 29.8 GiB > [ 2.708406] mmcblk0: p1 p2 > > This is just HS mode. > > In the same time isn't UHS-I backward compatible? Your report seems > surprising. Right. it's not issue. just working as lower mode than its capability. Best Regards, Jaehoon Chung > > Best regards, > Krzysztof > >> >> On warm boot: i.e reboot of the board. >> [ 4.649073] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot >> req 50000000Hz, actual 50000000HZ div = 0) >> [ 4.657555] mmc1: new high speed SDHC card at address aaaa >> [ 4.663787] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >> [ 4.669206] mmcblk0: p1 p2 >> >> On cold boot:: ie: power on the board. >> >> [ 4.630237] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot >> req 100000000Hz, actual 100000000HZ div = 0) >> [ 4.639820] mmc1: new ultra high speed SDR50 SDHC card at address aaaa >> [ 4.646266] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >> [ 4.650293] IRQ56 no longer affine to CPU7 >> [ 4.650581] CPU7: shutdown >> [ 4.658293] mmcblk0: p1 p2 >> >> Note: Their is need to reset the PMIC >> S2MPS11_REG_L13CTRL/S2MPS11_REG_L19CTRL registers >> to support this feature consistently on every reboot. >> >> -Anand Moon >> -- >> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in >> the body of a message to majordomo@vger.kernel.org >> More majordomo info at http://vger.kernel.org/majordomo-info.html >> Please read the FAQ at http://www.tux.org/lkml/ >> > > ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support 2015-10-12 13:04 ` Jaehoon Chung @ 2015-10-12 13:16 ` Krzysztof Kozlowski 2015-10-13 2:28 ` Jaehoon Chung 0 siblings, 1 reply; 50+ messages in thread From: Krzysztof Kozlowski @ 2015-10-12 13:16 UTC (permalink / raw) To: Jaehoon Chung, Anand Moon Cc: k.kozlowski.k, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, devicetree, linux-arm-kernel, linux-samsung-soc@vger.kernel.org, Linux Kernel W dniu 12.10.2015 o 22:04, Jaehoon Chung pisze: > On 10/12/2015 09:42 PM, Krzysztof Kozlowski wrote: >> W dniu 12.10.2015 o 19:46, Anand Moon pisze: >>> Hi Krzysztof, >>> >>> On 12 October 2015 at 11:14, Krzysztof Kozlowski >>> <k.kozlowski@samsung.com> wrote: >>>> On 12.10.2015 00:46, Anand Moon wrote: >>>>> Added support for UHS-I bus speed 50MB/s (SDR50, DDR50) 104MB/s (SDR104) >>>> >>>> This description is not entirely correct. The MMC driver already >>>> supports these UHS speeds (you did not any code) so you rather enabled >>>> it (description of bindings says "is supported"). >>>> >>>> You mentioned DDR50 but I don't see respective property below. >>> Looks like I missed it, I will add this in the next patch, >>>> >>>> How do you know that these modes are really supported? I don't know. Can >>>> you convince me? >> >> That part was not answered... > > In my experiment, it needs two requirements. > One is that Host controller supported UHS-I mode or others, other is SD-card. > In Anand's commit message, there is no information for this. > > And 50MB/s or 104MB/s is not real performance. (Just theoretical values) > It seems that can get those performances. Right. But do you know if the host actually supports these? > >> >>>> >>> >>>>> >>>>> Signed-off-by: Anand Moon <linux.amoon@gmail.com> >>>>> >>>>> --- >>>>> Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch >>>>> >>>>> Changes Fixed the UHS-I bus speed detedtion on cold boot. >>>> >>>> I don't get what is exactly fixed here. What was the error? What is the >>>> outcome of this fix? The log below is before or after? >>>> >>>> Best regards, >>>> Krzysztof >>>> >>>>> >>>>> [ 2.439806] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 100000000Hz, actual 100000000HZ div = 0) >>>>> [ 2.449729] mmc1: new ultra high speed SDR50 SDHC card at address aaaa >>>>> [ 2.455984] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >>>>> [ 2.461743] mmcblk0: p1 p2 >>>> >>>>> --- >>>>> arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 4 ++++ >>>>> 1 file changed, 4 insertions(+) >>>>> >>>>> diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>>> index 58c06d3..ba4a87b 100644 >>>>> --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>>> +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>>> @@ -364,6 +364,10 @@ >>>>> pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; >>>>> bus-width = <4>; >>>>> cap-sd-highspeed; >>>>> + sd-uhs-sdr12; >>>>> + sd-uhs-sdr25; >>>>> + sd-uhs-sdr50; >>>>> + sd-uhs-sdr104; >>>>> }; >>>>> >>>>> &pinctrl_0 { >>>>> >>>> >>> >>> Changes were made to support Sandisk Ultra UHS-I class 10 card support. >>> OdroidXU3/XU4 board would not boot up using this card. >>> >>> Depending on the capability of the UHS-I card, the speed of the card >>> is selected. >>> I have just added the enhance capability feature to support them. >> >> So without these capabilities mentioned microSD card cannot be used? So >> I have a UHS-I card, that one exactly: >> http://www.samsung.com/us/support/owners/product/MB-MP32D/APC >> >> It works: >> [ 2.628365] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req >> 50000000Hz, actual 50000000HZ div = 0) >> [ 2.693296] mmc1: new high speed SDHC card at address 0001 >> [ 2.703867] mmcblk0: mmc1:0001 00000 29.8 GiB >> [ 2.708406] mmcblk0: p1 p2 >> >> This is just HS mode. >> >> In the same time isn't UHS-I backward compatible? Your report seems >> surprising. > > Right. it's not issue. just working as lower mode than its capability. Anand's report mentions "board would not boot up" which seems quite drastic. :) Thanks Jaehoon for help in reviewing this patch. Dear Anand, Could you describe in more details observable issues, what is fixed or what feature is added? Best regards, Krzysztof > > Best Regards, > Jaehoon Chung > >> >> Best regards, >> Krzysztof >> >>> >>> On warm boot: i.e reboot of the board. >>> [ 4.649073] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot >>> req 50000000Hz, actual 50000000HZ div = 0) >>> [ 4.657555] mmc1: new high speed SDHC card at address aaaa >>> [ 4.663787] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >>> [ 4.669206] mmcblk0: p1 p2 >>> >>> On cold boot:: ie: power on the board. >>> >>> [ 4.630237] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot >>> req 100000000Hz, actual 100000000HZ div = 0) >>> [ 4.639820] mmc1: new ultra high speed SDR50 SDHC card at address aaaa >>> [ 4.646266] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >>> [ 4.650293] IRQ56 no longer affine to CPU7 >>> [ 4.650581] CPU7: shutdown >>> [ 4.658293] mmcblk0: p1 p2 >>> >>> Note: Their is need to reset the PMIC >>> S2MPS11_REG_L13CTRL/S2MPS11_REG_L19CTRL registers >>> to support this feature consistently on every reboot. >>> >>> -Anand Moon >>> -- >>> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in >>> the body of a message to majordomo@vger.kernel.org >>> More majordomo info at http://vger.kernel.org/majordomo-info.html >>> Please read the FAQ at http://www.tux.org/lkml/ >>> >> >> > ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support 2015-10-12 13:16 ` Krzysztof Kozlowski @ 2015-10-13 2:28 ` Jaehoon Chung 0 siblings, 0 replies; 50+ messages in thread From: Jaehoon Chung @ 2015-10-13 2:28 UTC (permalink / raw) To: Krzysztof Kozlowski, Anand Moon Cc: k.kozlowski.k, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, devicetree, linux-arm-kernel, linux-samsung-soc@vger.kernel.org, Linux Kernel On 10/12/2015 10:16 PM, Krzysztof Kozlowski wrote: > W dniu 12.10.2015 o 22:04, Jaehoon Chung pisze: >> On 10/12/2015 09:42 PM, Krzysztof Kozlowski wrote: >>> W dniu 12.10.2015 o 19:46, Anand Moon pisze: >>>> Hi Krzysztof, >>>> >>>> On 12 October 2015 at 11:14, Krzysztof Kozlowski >>>> <k.kozlowski@samsung.com> wrote: >>>>> On 12.10.2015 00:46, Anand Moon wrote: >>>>>> Added support for UHS-I bus speed 50MB/s (SDR50, DDR50) 104MB/s (SDR104) >>>>> >>>>> This description is not entirely correct. The MMC driver already >>>>> supports these UHS speeds (you did not any code) so you rather enabled >>>>> it (description of bindings says "is supported"). >>>>> >>>>> You mentioned DDR50 but I don't see respective property below. >>>> Looks like I missed it, I will add this in the next patch, >>>>> >>>>> How do you know that these modes are really supported? I don't know. Can >>>>> you convince me? >>> >>> That part was not answered... >> >> In my experiment, it needs two requirements. >> One is that Host controller supported UHS-I mode or others, other is SD-card. >> In Anand's commit message, there is no information for this. >> >> And 50MB/s or 104MB/s is not real performance. (Just theoretical values) >> It seems that can get those performances. > > Right. But do you know if the host actually supports these? Actually, it needs to check the User Manual for SoC. If i can't check the User manual, i can't also know whether it supports or not. Especially, there is no register that can be known which SD specification version at dw-mmc controller. Well, if i miss something, let me know. I will also check more. Best Regards, Jaehoon Chung > >> >>> >>>>> >>>> >>>>>> >>>>>> Signed-off-by: Anand Moon <linux.amoon@gmail.com> >>>>>> >>>>>> --- >>>>>> Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch >>>>>> >>>>>> Changes Fixed the UHS-I bus speed detedtion on cold boot. >>>>> >>>>> I don't get what is exactly fixed here. What was the error? What is the >>>>> outcome of this fix? The log below is before or after? >>>>> >>>>> Best regards, >>>>> Krzysztof >>>>> >>>>>> >>>>>> [ 2.439806] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 100000000Hz, actual 100000000HZ div = 0) >>>>>> [ 2.449729] mmc1: new ultra high speed SDR50 SDHC card at address aaaa >>>>>> [ 2.455984] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >>>>>> [ 2.461743] mmcblk0: p1 p2 >>>>> >>>>>> --- >>>>>> arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 4 ++++ >>>>>> 1 file changed, 4 insertions(+) >>>>>> >>>>>> diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>>>> index 58c06d3..ba4a87b 100644 >>>>>> --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>>>> +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >>>>>> @@ -364,6 +364,10 @@ >>>>>> pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; >>>>>> bus-width = <4>; >>>>>> cap-sd-highspeed; >>>>>> + sd-uhs-sdr12; >>>>>> + sd-uhs-sdr25; >>>>>> + sd-uhs-sdr50; >>>>>> + sd-uhs-sdr104; >>>>>> }; >>>>>> >>>>>> &pinctrl_0 { >>>>>> >>>>> >>>> >>>> Changes were made to support Sandisk Ultra UHS-I class 10 card support. >>>> OdroidXU3/XU4 board would not boot up using this card. >>>> >>>> Depending on the capability of the UHS-I card, the speed of the card >>>> is selected. >>>> I have just added the enhance capability feature to support them. >>> >>> So without these capabilities mentioned microSD card cannot be used? So >>> I have a UHS-I card, that one exactly: >>> http://www.samsung.com/us/support/owners/product/MB-MP32D/APC >>> >>> It works: >>> [ 2.628365] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req >>> 50000000Hz, actual 50000000HZ div = 0) >>> [ 2.693296] mmc1: new high speed SDHC card at address 0001 >>> [ 2.703867] mmcblk0: mmc1:0001 00000 29.8 GiB >>> [ 2.708406] mmcblk0: p1 p2 >>> >>> This is just HS mode. >>> >>> In the same time isn't UHS-I backward compatible? Your report seems >>> surprising. >> >> Right. it's not issue. just working as lower mode than its capability. > > Anand's report mentions "board would not boot up" which seems quite > drastic. :) > > Thanks Jaehoon for help in reviewing this patch. > > > Dear Anand, > > Could you describe in more details observable issues, what is fixed or > what feature is added? > > Best regards, > Krzysztof > >> >> Best Regards, >> Jaehoon Chung >> >>> >>> Best regards, >>> Krzysztof >>> >>>> >>>> On warm boot: i.e reboot of the board. >>>> [ 4.649073] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot >>>> req 50000000Hz, actual 50000000HZ div = 0) >>>> [ 4.657555] mmc1: new high speed SDHC card at address aaaa >>>> [ 4.663787] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >>>> [ 4.669206] mmcblk0: p1 p2 >>>> >>>> On cold boot:: ie: power on the board. >>>> >>>> [ 4.630237] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot >>>> req 100000000Hz, actual 100000000HZ div = 0) >>>> [ 4.639820] mmc1: new ultra high speed SDR50 SDHC card at address aaaa >>>> [ 4.646266] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >>>> [ 4.650293] IRQ56 no longer affine to CPU7 >>>> [ 4.650581] CPU7: shutdown >>>> [ 4.658293] mmcblk0: p1 p2 >>>> >>>> Note: Their is need to reset the PMIC >>>> S2MPS11_REG_L13CTRL/S2MPS11_REG_L19CTRL registers >>>> to support this feature consistently on every reboot. >>>> >>>> -Anand Moon >>>> -- >>>> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in >>>> the body of a message to majordomo@vger.kernel.org >>>> More majordomo info at http://vger.kernel.org/majordomo-info.html >>>> Please read the FAQ at http://www.tux.org/lkml/ >>>> >>> >>> >> > > ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support 2015-10-12 5:44 ` Krzysztof Kozlowski 2015-10-12 10:46 ` Anand Moon @ 2015-10-12 15:32 ` Anand Moon 2015-10-13 0:14 ` Krzysztof Kozlowski 1 sibling, 1 reply; 50+ messages in thread From: Anand Moon @ 2015-10-12 15:32 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung, devicetree, linux-arm-kernel, linux-samsung-soc@vger.kernel.org, Linux Kernel Hi Krzysztof, On 12 October 2015 at 11:14, Krzysztof Kozlowski <k.kozlowski@samsung.com> wrote: > On 12.10.2015 00:46, Anand Moon wrote: >> Added support for UHS-I bus speed 50MB/s (SDR50, DDR50) 104MB/s (SDR104) > > This description is not entirely correct. The MMC driver already > supports these UHS speeds (you did not any code) so you rather enabled > it (description of bindings says "is supported"). > > You mentioned DDR50 but I don't see respective property below. > > How do you know that these modes are really supported? I don't know. Can > you convince me? Setting this DDR50 capability give me this error. That's the reason to drop this capability. Sep 24 09:37:04 odroidxu4 kernel: [ 4.138418] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) Sep 24 09:37:04 odroidxu4 kernel: [ 4.138546] mmc1: new ultra high speed DDR50 SDHC card at address aaaa Sep 24 09:37:04 odroidxu4 kernel: [ 4.141585] mmcblk0: mmc1:aaaa SL32G 29.7 GiB Sep 24 09:37:04 odroidxu4 kernel: [ 4.146477] mmcblk0: error -110 sending status command, retrying Sep 24 09:37:04 odroidxu4 kernel: [ 4.146577] mmcblk0: error -115 sending stop command, original cmd response 0x900, card status 0x900 Sep 24 09:37:04 odroidxu4 kernel: [ 4.146581] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0 >> >> Signed-off-by: Anand Moon <linux.amoon@gmail.com> >> >> --- >> Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch >> >> Changes Fixed the UHS-I bus speed detedtion on cold boot. > > I don't get what is exactly fixed here. What was the error? What is the > outcome of this fix? The log below is before or after? > > Best regards, > Krzysztof > >> >> [ 2.439806] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 100000000Hz, actual 100000000HZ div = 0) >> [ 2.449729] mmc1: new ultra high speed SDR50 SDHC card at address aaaa >> [ 2.455984] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >> [ 2.461743] mmcblk0: p1 p2 > >> --- >> arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 4 ++++ >> 1 file changed, 4 insertions(+) >> >> diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >> index 58c06d3..ba4a87b 100644 >> --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >> +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >> @@ -364,6 +364,10 @@ >> pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; >> bus-width = <4>; >> cap-sd-highspeed; >> + sd-uhs-sdr12; >> + sd-uhs-sdr25; >> + sd-uhs-sdr50; >> + sd-uhs-sdr104; >> }; >> >> &pinctrl_0 { >> > -Anand Moon ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support 2015-10-12 15:32 ` Anand Moon @ 2015-10-13 0:14 ` Krzysztof Kozlowski 2015-10-13 3:08 ` Anand Moon 0 siblings, 1 reply; 50+ messages in thread From: Krzysztof Kozlowski @ 2015-10-13 0:14 UTC (permalink / raw) To: Anand Moon Cc: Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung, devicetree, linux-arm-kernel, linux-samsung-soc@vger.kernel.org, Linux Kernel On 13.10.2015 00:32, Anand Moon wrote: > Hi Krzysztof, > > On 12 October 2015 at 11:14, Krzysztof Kozlowski > <k.kozlowski@samsung.com> wrote: >> On 12.10.2015 00:46, Anand Moon wrote: >>> Added support for UHS-I bus speed 50MB/s (SDR50, DDR50) 104MB/s (SDR104) >> >> This description is not entirely correct. The MMC driver already >> supports these UHS speeds (you did not any code) so you rather enabled >> it (description of bindings says "is supported"). >> >> You mentioned DDR50 but I don't see respective property below. >> >> How do you know that these modes are really supported? I don't know. Can >> you convince me? > > Setting this DDR50 capability give me this error. That's the reason to > drop this capability. But you mentioned it in commit message! "Added support for UHS-I ... (DDR50)" In the same time dropping DDR50 is not an sufficient proof that "SDR50 and SDR104 are really supported". Best regards, Krzysztof ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support 2015-10-13 0:14 ` Krzysztof Kozlowski @ 2015-10-13 3:08 ` Anand Moon 2015-10-13 3:43 ` Krzysztof Kozlowski 0 siblings, 1 reply; 50+ messages in thread From: Anand Moon @ 2015-10-13 3:08 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung, devicetree, linux-arm-kernel, linux-samsung-soc@vger.kernel.org, Linux Kernel Hi Krzysztof, On 13 October 2015 at 05:44, Krzysztof Kozlowski <k.kozlowski@samsung.com> wrote: > On 13.10.2015 00:32, Anand Moon wrote: >> Hi Krzysztof, >> >> On 12 October 2015 at 11:14, Krzysztof Kozlowski >> <k.kozlowski@samsung.com> wrote: >>> On 12.10.2015 00:46, Anand Moon wrote: >>>> Added support for UHS-I bus speed 50MB/s (SDR50, DDR50) 104MB/s (SDR104) >>> >>> This description is not entirely correct. The MMC driver already >>> supports these UHS speeds (you did not any code) so you rather enabled >>> it (description of bindings says "is supported"). >>> >>> You mentioned DDR50 but I don't see respective property below. >>> >>> How do you know that these modes are really supported? I don't know. Can >>> you convince me? >> >> Setting this DDR50 capability give me this error. That's the reason to >> drop this capability. > > But you mentioned it in commit message! "Added support for UHS-I ... > (DDR50)" > > In the same time dropping DDR50 is not an sufficient proof that "SDR50 > and SDR104 are really supported". > These changes are related to the microSD card capabilities. So SDR50 have better frequency over DDR50. On the same Sandisk card. When the card select the capability for DDR50 --------------------------------------------------- [ 4.001477] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 4.001604] mmc1: new ultra high speed DDR50 SDHC card at address aaaa [ 4.004505] mmcblk0: mmc1:aaaa SL32G 29.7 GiB [ 4.009179] mmcblk0: error -110 sending status command, retrying [ 4.009271] mmcblk0: error -115 sending stop command, original cmd response 0x900, card status 0x900 [ 4.009275] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0x0 [ 4.025563] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 4.067770] Console: switching to colour frame buffer device 274x77 [ 4.098782] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 4.099692] mmc1: tried to reset card [ 4.101332] mmcblk0: p1 p2 When the card select the capability for SDR50 --------------------------------------------------------------------------------- [ 2.439806] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 100000000Hz, actual 100000000HZ div = 0) [ 2.449729] mmc1: new ultra high speed SDR50 SDHC card at address aaaa [ 2.455984] mmcblk0: mmc1:aaaa SL32G 29.7 GiB [ 2.461743] mmcblk0: p1 p2 Which will relate to better read/write speed. -Anand Moon > Best regards, > Krzysztof > ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support 2015-10-13 3:08 ` Anand Moon @ 2015-10-13 3:43 ` Krzysztof Kozlowski [not found] ` <561C7DF1.6000609-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> 0 siblings, 1 reply; 50+ messages in thread From: Krzysztof Kozlowski @ 2015-10-13 3:43 UTC (permalink / raw) To: Anand Moon Cc: Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung, devicetree, linux-arm-kernel, linux-samsung-soc@vger.kernel.org, Linux Kernel On 13.10.2015 12:08, Anand Moon wrote: > Hi Krzysztof, > > On 13 October 2015 at 05:44, Krzysztof Kozlowski > <k.kozlowski@samsung.com> wrote: >> On 13.10.2015 00:32, Anand Moon wrote: >>> Hi Krzysztof, >>> >>> On 12 October 2015 at 11:14, Krzysztof Kozlowski >>> <k.kozlowski@samsung.com> wrote: >>>> On 12.10.2015 00:46, Anand Moon wrote: >>>>> Added support for UHS-I bus speed 50MB/s (SDR50, DDR50) 104MB/s (SDR104) >>>> >>>> This description is not entirely correct. The MMC driver already >>>> supports these UHS speeds (you did not any code) so you rather enabled >>>> it (description of bindings says "is supported"). >>>> >>>> You mentioned DDR50 but I don't see respective property below. >>>> >>>> How do you know that these modes are really supported? I don't know. Can >>>> you convince me? >>> >>> Setting this DDR50 capability give me this error. That's the reason to >>> drop this capability. >> >> But you mentioned it in commit message! "Added support for UHS-I ... >> (DDR50)" >> >> In the same time dropping DDR50 is not an sufficient proof that "SDR50 >> and SDR104 are really supported". >> > > These changes are related to the microSD card capabilities. > So SDR50 have better frequency over DDR50. On the same Sandisk card. > > When the card select the capability for DDR50 > --------------------------------------------------- > [ 4.001477] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot > req 50000000Hz, actual 50000000HZ div = 0) > [ 4.001604] mmc1: new ultra high speed DDR50 SDHC card at address aaaa > [ 4.004505] mmcblk0: mmc1:aaaa SL32G 29.7 GiB > [ 4.009179] mmcblk0: error -110 sending status command, retrying > [ 4.009271] mmcblk0: error -115 sending stop command, original cmd > response 0x900, card status 0x900 > [ 4.009275] mmcblk0: error -84 transferring data, sector 0, nr 8, > cmd response 0x900, card status 0x0 > [ 4.025563] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot > req 400000Hz, actual 396825HZ div = 63) > [ 4.067770] Console: switching to colour frame buffer device 274x77 > [ 4.098782] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot > req 50000000Hz, actual 50000000HZ div = 0) > [ 4.099692] mmc1: tried to reset card > [ 4.101332] mmcblk0: p1 p2 > > > When the card select the capability for SDR50 > --------------------------------------------------------------------------------- > [ 2.439806] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req > 100000000Hz, actual 100000000HZ div = 0) > [ 2.449729] mmc1: new ultra high speed SDR50 SDHC card at address aaaa > [ 2.455984] mmcblk0: mmc1:aaaa SL32G 29.7 GiB > [ 2.461743] mmcblk0: p1 p2 > > Which will relate to better read/write speed. Which is not an answer to my question. To none of my previous questions. Best regards, Krzysztof ^ permalink raw reply [flat|nested] 50+ messages in thread
[parent not found: <561C7DF1.6000609-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>]
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support [not found] ` <561C7DF1.6000609-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> @ 2015-10-13 3:49 ` Anand Moon 2015-10-13 16:27 ` Anand Moon 1 sibling, 0 replies; 50+ messages in thread From: Anand Moon @ 2015-10-13 3:49 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-samsung-soc-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, Linux Kernel Hi Krzysztof, On 13 October 2015 at 09:13, Krzysztof Kozlowski <k.kozlowski-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> wrote: > On 13.10.2015 12:08, Anand Moon wrote: >> Hi Krzysztof, >> >> On 13 October 2015 at 05:44, Krzysztof Kozlowski >> <k.kozlowski-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> wrote: >>> On 13.10.2015 00:32, Anand Moon wrote: >>>> Hi Krzysztof, >>>> >>>> On 12 October 2015 at 11:14, Krzysztof Kozlowski >>>> <k.kozlowski-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> wrote: >>>>> On 12.10.2015 00:46, Anand Moon wrote: >>>>>> Added support for UHS-I bus speed 50MB/s (SDR50, DDR50) 104MB/s (SDR104) >>>>> >>>>> This description is not entirely correct. The MMC driver already >>>>> supports these UHS speeds (you did not any code) so you rather enabled >>>>> it (description of bindings says "is supported"). >>>>> >>>>> You mentioned DDR50 but I don't see respective property below. >>>>> >>>>> How do you know that these modes are really supported? I don't know. Can >>>>> you convince me? >>>> >>>> Setting this DDR50 capability give me this error. That's the reason to >>>> drop this capability. >>> >>> But you mentioned it in commit message! "Added support for UHS-I ... >>> (DDR50)" >>> >>> In the same time dropping DDR50 is not an sufficient proof that "SDR50 >>> and SDR104 are really supported". >>> >> >> These changes are related to the microSD card capabilities. >> So SDR50 have better frequency over DDR50. On the same Sandisk card. >> >> When the card select the capability for DDR50 >> --------------------------------------------------- >> [ 4.001477] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot >> req 50000000Hz, actual 50000000HZ div = 0) >> [ 4.001604] mmc1: new ultra high speed DDR50 SDHC card at address aaaa >> [ 4.004505] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >> [ 4.009179] mmcblk0: error -110 sending status command, retrying >> [ 4.009271] mmcblk0: error -115 sending stop command, original cmd >> response 0x900, card status 0x900 >> [ 4.009275] mmcblk0: error -84 transferring data, sector 0, nr 8, >> cmd response 0x900, card status 0x0 >> [ 4.025563] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot >> req 400000Hz, actual 396825HZ div = 63) >> [ 4.067770] Console: switching to colour frame buffer device 274x77 >> [ 4.098782] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot >> req 50000000Hz, actual 50000000HZ div = 0) >> [ 4.099692] mmc1: tried to reset card >> [ 4.101332] mmcblk0: p1 p2 >> >> >> When the card select the capability for SDR50 >> --------------------------------------------------------------------------------- >> [ 2.439806] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req >> 100000000Hz, actual 100000000HZ div = 0) >> [ 2.449729] mmc1: new ultra high speed SDR50 SDHC card at address aaaa >> [ 2.455984] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >> [ 2.461743] mmcblk0: p1 p2 >> >> Which will relate to better read/write speed. > > Which is not an answer to my question. To none of my previous questions. OK, you are correct.Just ignore these changes. -Anand Moon > > Best regards, > Krzysztof -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support [not found] ` <561C7DF1.6000609-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> 2015-10-13 3:49 ` Anand Moon @ 2015-10-13 16:27 ` Anand Moon 2015-10-13 23:59 ` Krzysztof Kozlowski 1 sibling, 1 reply; 50+ messages in thread From: Anand Moon @ 2015-10-13 16:27 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung, devicetree-u79uwXL29TY76Z2rM5mHXA, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, linux-samsung-soc-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, Linux Kernel Hi Krzysztof, On 13 October 2015 at 09:13, Krzysztof Kozlowski <k.kozlowski-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> wrote: > > On 13.10.2015 12:08, Anand Moon wrote: > > Hi Krzysztof, > > > > On 13 October 2015 at 05:44, Krzysztof Kozlowski > > <k.kozlowski-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> wrote: > >> On 13.10.2015 00:32, Anand Moon wrote: > >>> Hi Krzysztof, > >>> > >>> On 12 October 2015 at 11:14, Krzysztof Kozlowski > >>> <k.kozlowski-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> wrote: > >>>> On 12.10.2015 00:46, Anand Moon wrote: > >>>>> Added support for UHS-I bus speed 50MB/s (SDR50, DDR50) 104MB/s (SDR104) > >>>> > >>>> This description is not entirely correct. The MMC driver already > >>>> supports these UHS speeds (you did not any code) so you rather enabled > >>>> it (description of bindings says "is supported"). > >>>> > >>>> You mentioned DDR50 but I don't see respective property below. > >>>> > >>>> How do you know that these modes are really supported? I don't know. Can > >>>> you convince me? > >>> > >>> Setting this DDR50 capability give me this error. That's the reason to > >>> drop this capability. > >> > >> But you mentioned it in commit message! "Added support for UHS-I ... > >> (DDR50)" > >> > >> In the same time dropping DDR50 is not an sufficient proof that "SDR50 > >> and SDR104 are really supported". > >> > > > > These changes are related to the microSD card capabilities. > > So SDR50 have better frequency over DDR50. On the same Sandisk card. > > > > When the card select the capability for DDR50 > > --------------------------------------------------- > > [ 4.001477] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot > > req 50000000Hz, actual 50000000HZ div = 0) > > [ 4.001604] mmc1: new ultra high speed DDR50 SDHC card at address aaaa > > [ 4.004505] mmcblk0: mmc1:aaaa SL32G 29.7 GiB > > [ 4.009179] mmcblk0: error -110 sending status command, retrying > > [ 4.009271] mmcblk0: error -115 sending stop command, original cmd > > response 0x900, card status 0x900 > > [ 4.009275] mmcblk0: error -84 transferring data, sector 0, nr 8, > > cmd response 0x900, card status 0x0 > > [ 4.025563] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot > > req 400000Hz, actual 396825HZ div = 63) > > [ 4.067770] Console: switching to colour frame buffer device 274x77 > > [ 4.098782] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot > > req 50000000Hz, actual 50000000HZ div = 0) > > [ 4.099692] mmc1: tried to reset card > > [ 4.101332] mmcblk0: p1 p2 > > > > > > When the card select the capability for SDR50 > > --------------------------------------------------------------------------------- > > [ 2.439806] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req > > 100000000Hz, actual 100000000HZ div = 0) > > [ 2.449729] mmc1: new ultra high speed SDR50 SDHC card at address aaaa > > [ 2.455984] mmcblk0: mmc1:aaaa SL32G 29.7 GiB > > [ 2.461743] mmcblk0: p1 p2 > > > > Which will relate to better read/write speed. > > Which is not an answer to my question. To none of my previous questions. > Basically UHS-I capability (sd-uhs-sdr12, sd-uhs-sdr25, sd-uhs-sdr50, sd-uhs-sdr104) help tune speed supported for mmc I have tired to compare the speed on high speed UHS-I vs ultra high speed UHS-I using izone utility. [ 2.572469] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 2.572609] mmc1: new high speed SDHC card at address aaaa Command line used: ./iozone -L64 -S32 -azecwI -+n -r4k -r64k -r128k -s10M -i0 -i1 -i2 -f datafile -Rb out.xls Output is in kBytes/sec Time Resolution = 0.000001 seconds. Processor cache size set to 32 kBytes. Processor cache line size set to 64 bytes. File stride size set to 17 * record size. random random bkwd record stride kB reclen write rewrite read reread read write read rewrite read fwrite frewrite fread freread 10240 4 1631 0 6556 0 5538 982 10240 64 8828 0 18897 0 17994 303 10240 128 6269 0 20670 0 20128 1096 --------------------------------------------------------------------------------------------------------- [ 2.613761] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 100000000Hz, actual 100000000HZ div = 0) [ 2.623573] mmc1: new ultra high speed SDR50 SDHC card at address aaaa Command line used: ./iozone -L64 -S32 -azecwI -+n -r4k -r64k -r128k -s10M -i0 -i1 -i2 -f datafile -Rb out.xls Output is in kBytes/sec Time Resolution = 0.000001 seconds. Processor cache size set to 32 kBytes. Processor cache line size set to 64 bytes. File stride size set to 17 * record size. random random bkwd record stride kB reclen write rewrite read reread read write read rewrite read fwrite frewrite fread freread 10240 4 1809 0 7507 0 5233 859 10240 64 11622 0 31250 0 28072 516 10240 128 4320 0 34417 0 32509 1148 My observation is that their slight increase in read/write operation. Hope I have tried to answer you query. If I am wrong please let me know. -Anand Moon > > Best regards, > Krzysztof -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support 2015-10-13 16:27 ` Anand Moon @ 2015-10-13 23:59 ` Krzysztof Kozlowski 2015-10-14 1:06 ` Alim Akhtar 2015-10-14 3:58 ` Anand Moon 0 siblings, 2 replies; 50+ messages in thread From: Krzysztof Kozlowski @ 2015-10-13 23:59 UTC (permalink / raw) To: Anand Moon Cc: Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung, devicetree, linux-arm-kernel, linux-samsung-soc@vger.kernel.org, Linux Kernel On 14.10.2015 01:27, Anand Moon wrote: > Hi Krzysztof, > > On 13 October 2015 at 09:13, Krzysztof Kozlowski > <k.kozlowski@samsung.com> wrote: >> >> On 13.10.2015 12:08, Anand Moon wrote: >>> Hi Krzysztof, >>> >>> On 13 October 2015 at 05:44, Krzysztof Kozlowski >>> <k.kozlowski@samsung.com> wrote: >>>> On 13.10.2015 00:32, Anand Moon wrote: >>>>> Hi Krzysztof, >>>>> >>>>> On 12 October 2015 at 11:14, Krzysztof Kozlowski >>>>> <k.kozlowski@samsung.com> wrote: >>>>>> On 12.10.2015 00:46, Anand Moon wrote: >>>>>>> Added support for UHS-I bus speed 50MB/s (SDR50, DDR50) 104MB/s (SDR104) >>>>>> >>>>>> This description is not entirely correct. The MMC driver already >>>>>> supports these UHS speeds (you did not any code) so you rather enabled >>>>>> it (description of bindings says "is supported"). >>>>>> >>>>>> You mentioned DDR50 but I don't see respective property below. >>>>>> >>>>>> How do you know that these modes are really supported? I don't know. Can >>>>>> you convince me? >>>>> >>>>> Setting this DDR50 capability give me this error. That's the reason to >>>>> drop this capability. >>>> >>>> But you mentioned it in commit message! "Added support for UHS-I ... >>>> (DDR50)" >>>> >>>> In the same time dropping DDR50 is not an sufficient proof that "SDR50 >>>> and SDR104 are really supported". >>>> >>> >>> These changes are related to the microSD card capabilities. >>> So SDR50 have better frequency over DDR50. On the same Sandisk card. >>> >>> When the card select the capability for DDR50 >>> --------------------------------------------------- >>> [ 4.001477] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot >>> req 50000000Hz, actual 50000000HZ div = 0) >>> [ 4.001604] mmc1: new ultra high speed DDR50 SDHC card at address aaaa >>> [ 4.004505] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >>> [ 4.009179] mmcblk0: error -110 sending status command, retrying >>> [ 4.009271] mmcblk0: error -115 sending stop command, original cmd >>> response 0x900, card status 0x900 >>> [ 4.009275] mmcblk0: error -84 transferring data, sector 0, nr 8, >>> cmd response 0x900, card status 0x0 >>> [ 4.025563] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot >>> req 400000Hz, actual 396825HZ div = 63) >>> [ 4.067770] Console: switching to colour frame buffer device 274x77 >>> [ 4.098782] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot >>> req 50000000Hz, actual 50000000HZ div = 0) >>> [ 4.099692] mmc1: tried to reset card >>> [ 4.101332] mmcblk0: p1 p2 >>> >>> >>> When the card select the capability for SDR50 >>> --------------------------------------------------------------------------------- >>> [ 2.439806] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req >>> 100000000Hz, actual 100000000HZ div = 0) >>> [ 2.449729] mmc1: new ultra high speed SDR50 SDHC card at address aaaa >>> [ 2.455984] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >>> [ 2.461743] mmcblk0: p1 p2 >>> >>> Which will relate to better read/write speed. >> >> Which is not an answer to my question. To none of my previous questions. >> > > Basically UHS-I capability (sd-uhs-sdr12, sd-uhs-sdr25, sd-uhs-sdr50, > sd-uhs-sdr104) help tune speed supported for mmc > > I have tired to compare the speed on high speed UHS-I vs ultra high > speed UHS-I using izone utility. > > [ 2.572469] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot > req 50000000Hz, actual 50000000HZ div = 0) > [ 2.572609] mmc1: new high speed SDHC card at address aaaa > > Command line used: ./iozone -L64 -S32 -azecwI -+n -r4k -r64k > -r128k -s10M -i0 -i1 -i2 -f datafile -Rb out.xls > Output is in kBytes/sec > Time Resolution = 0.000001 seconds. > Processor cache size set to 32 kBytes. > Processor cache line size set to 64 bytes. > File stride size set to 17 * record size. > random > random bkwd record stride > kB reclen write rewrite read reread read > write read rewrite read fwrite frewrite fread > freread > 10240 4 1631 0 6556 0 5538 982 > 10240 64 8828 0 18897 0 17994 303 > 10240 128 6269 0 20670 0 20128 1096 > --------------------------------------------------------------------------------------------------------- > [ 2.613761] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot > req 100000000Hz, actual 100000000HZ div = 0) > [ 2.623573] mmc1: new ultra high speed SDR50 SDHC card at address aaaa > > Command line used: ./iozone -L64 -S32 -azecwI -+n -r4k -r64k > -r128k -s10M -i0 -i1 -i2 -f datafile -Rb out.xls > Output is in kBytes/sec > Time Resolution = 0.000001 seconds. > Processor cache size set to 32 kBytes. > Processor cache line size set to 64 bytes. > File stride size set to 17 * record size. > random > random bkwd record stride > kB reclen write rewrite read reread read > write read rewrite read fwrite frewrite fread > freread > 10240 4 1809 0 7507 0 5233 859 > 10240 64 11622 0 31250 0 28072 516 > 10240 128 4320 0 34417 0 32509 1148 > > My observation is that their slight increase in read/write operation. > > Hope I have tried to answer you query. If I am wrong please let me know. Nope, that did not answer my query. You gave some performance benchmarks but my question was not about the speed of anything. The question is (once again): How do you know that these modes are really supported? You are marking the *host* as supporting these modes. Please provide information that host supports them *really*, not by experimenting "oh, it seems to work now, maybe it will work always". Usually vendors, if their products implement some kind of specification/protocol, they mark the products as "compatible with XYZ" etc. Best regards, Krzysztof ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support 2015-10-13 23:59 ` Krzysztof Kozlowski @ 2015-10-14 1:06 ` Alim Akhtar 2015-10-14 1:15 ` Krzysztof Kozlowski 2015-10-14 22:40 ` Doug Anderson 2015-10-14 3:58 ` Anand Moon 1 sibling, 2 replies; 50+ messages in thread From: Alim Akhtar @ 2015-10-14 1:06 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Anand Moon, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-samsung-soc@vger.kernel.org, Linux Kernel, Douglas Anderson +Doug Hello, AFAIR, dw_mmc host controller does support UHS-I [1], specially SDR50 and SDR104 modes. [1]: http://www.spinics.net/lists/linux-mmc/msg28186.html What I remember is, one need to set "broken-cd" property also in order to make it work because of the vqmmc and vmmc connection on board. I didn't find the link right now, but you can search on the web, there was a long discussion about handling this. Have not checked it recently, so not sure if this got broken somehow. Regards, Alim On Wed, Oct 14, 2015 at 5:29 AM, Krzysztof Kozlowski <k.kozlowski@samsung.com> wrote: > On 14.10.2015 01:27, Anand Moon wrote: >> Hi Krzysztof, >> >> On 13 October 2015 at 09:13, Krzysztof Kozlowski >> <k.kozlowski@samsung.com> wrote: >>> >>> On 13.10.2015 12:08, Anand Moon wrote: >>>> Hi Krzysztof, >>>> >>>> On 13 October 2015 at 05:44, Krzysztof Kozlowski >>>> <k.kozlowski@samsung.com> wrote: >>>>> On 13.10.2015 00:32, Anand Moon wrote: >>>>>> Hi Krzysztof, >>>>>> >>>>>> On 12 October 2015 at 11:14, Krzysztof Kozlowski >>>>>> <k.kozlowski@samsung.com> wrote: >>>>>>> On 12.10.2015 00:46, Anand Moon wrote: >>>>>>>> Added support for UHS-I bus speed 50MB/s (SDR50, DDR50) 104MB/s (SDR104) >>>>>>> >>>>>>> This description is not entirely correct. The MMC driver already >>>>>>> supports these UHS speeds (you did not any code) so you rather enabled >>>>>>> it (description of bindings says "is supported"). >>>>>>> >>>>>>> You mentioned DDR50 but I don't see respective property below. >>>>>>> >>>>>>> How do you know that these modes are really supported? I don't know. Can >>>>>>> you convince me? >>>>>> >>>>>> Setting this DDR50 capability give me this error. That's the reason to >>>>>> drop this capability. >>>>> >>>>> But you mentioned it in commit message! "Added support for UHS-I ... >>>>> (DDR50)" >>>>> >>>>> In the same time dropping DDR50 is not an sufficient proof that "SDR50 >>>>> and SDR104 are really supported". >>>>> >>>> >>>> These changes are related to the microSD card capabilities. >>>> So SDR50 have better frequency over DDR50. On the same Sandisk card. >>>> >>>> When the card select the capability for DDR50 >>>> --------------------------------------------------- >>>> [ 4.001477] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot >>>> req 50000000Hz, actual 50000000HZ div = 0) >>>> [ 4.001604] mmc1: new ultra high speed DDR50 SDHC card at address aaaa >>>> [ 4.004505] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >>>> [ 4.009179] mmcblk0: error -110 sending status command, retrying >>>> [ 4.009271] mmcblk0: error -115 sending stop command, original cmd >>>> response 0x900, card status 0x900 >>>> [ 4.009275] mmcblk0: error -84 transferring data, sector 0, nr 8, >>>> cmd response 0x900, card status 0x0 >>>> [ 4.025563] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot >>>> req 400000Hz, actual 396825HZ div = 63) >>>> [ 4.067770] Console: switching to colour frame buffer device 274x77 >>>> [ 4.098782] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot >>>> req 50000000Hz, actual 50000000HZ div = 0) >>>> [ 4.099692] mmc1: tried to reset card >>>> [ 4.101332] mmcblk0: p1 p2 >>>> >>>> >>>> When the card select the capability for SDR50 >>>> --------------------------------------------------------------------------------- >>>> [ 2.439806] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req >>>> 100000000Hz, actual 100000000HZ div = 0) >>>> [ 2.449729] mmc1: new ultra high speed SDR50 SDHC card at address aaaa >>>> [ 2.455984] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >>>> [ 2.461743] mmcblk0: p1 p2 >>>> >>>> Which will relate to better read/write speed. >>> >>> Which is not an answer to my question. To none of my previous questions. >>> >> >> Basically UHS-I capability (sd-uhs-sdr12, sd-uhs-sdr25, sd-uhs-sdr50, >> sd-uhs-sdr104) help tune speed supported for mmc >> >> I have tired to compare the speed on high speed UHS-I vs ultra high >> speed UHS-I using izone utility. >> >> [ 2.572469] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot >> req 50000000Hz, actual 50000000HZ div = 0) >> [ 2.572609] mmc1: new high speed SDHC card at address aaaa >> >> Command line used: ./iozone -L64 -S32 -azecwI -+n -r4k -r64k >> -r128k -s10M -i0 -i1 -i2 -f datafile -Rb out.xls >> Output is in kBytes/sec >> Time Resolution = 0.000001 seconds. >> Processor cache size set to 32 kBytes. >> Processor cache line size set to 64 bytes. >> File stride size set to 17 * record size. >> random >> random bkwd record stride >> kB reclen write rewrite read reread read >> write read rewrite read fwrite frewrite fread >> freread >> 10240 4 1631 0 6556 0 5538 982 >> 10240 64 8828 0 18897 0 17994 303 >> 10240 128 6269 0 20670 0 20128 1096 >> --------------------------------------------------------------------------------------------------------- >> [ 2.613761] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot >> req 100000000Hz, actual 100000000HZ div = 0) >> [ 2.623573] mmc1: new ultra high speed SDR50 SDHC card at address aaaa >> >> Command line used: ./iozone -L64 -S32 -azecwI -+n -r4k -r64k >> -r128k -s10M -i0 -i1 -i2 -f datafile -Rb out.xls >> Output is in kBytes/sec >> Time Resolution = 0.000001 seconds. >> Processor cache size set to 32 kBytes. >> Processor cache line size set to 64 bytes. >> File stride size set to 17 * record size. >> random >> random bkwd record stride >> kB reclen write rewrite read reread read >> write read rewrite read fwrite frewrite fread >> freread >> 10240 4 1809 0 7507 0 5233 859 >> 10240 64 11622 0 31250 0 28072 516 >> 10240 128 4320 0 34417 0 32509 1148 >> >> My observation is that their slight increase in read/write operation. >> >> Hope I have tried to answer you query. If I am wrong please let me know. > > Nope, that did not answer my query. You gave some performance benchmarks > but my question was not about the speed of anything. The question is > (once again): > How do you know that these modes are really supported? > > You are marking the *host* as supporting these modes. Please provide > information that host supports them *really*, not by experimenting "oh, > it seems to work now, maybe it will work always". > > Usually vendors, if their products implement some kind of > specification/protocol, they mark the products as "compatible with XYZ" etc. > > Best regards, > Krzysztof > -- > To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html -- Regards, Alim ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support 2015-10-14 1:06 ` Alim Akhtar @ 2015-10-14 1:15 ` Krzysztof Kozlowski 2015-10-14 1:40 ` Jaehoon Chung 2015-10-14 2:13 ` Alim Akhtar 2015-10-14 22:40 ` Doug Anderson 1 sibling, 2 replies; 50+ messages in thread From: Krzysztof Kozlowski @ 2015-10-14 1:15 UTC (permalink / raw) To: Alim Akhtar Cc: Anand Moon, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-samsung-soc@vger.kernel.org, Linux Kernel, Douglas Anderson On 14.10.2015 10:06, Alim Akhtar wrote: > +Doug > Hello, > AFAIR, dw_mmc host controller does support UHS-I [1], specially SDR50 > and SDR104 modes. > > [1]: http://www.spinics.net/lists/linux-mmc/msg28186.html > > What I remember is, one need to set "broken-cd" property also in order > to make it work because of the vqmmc and vmmc connection on board. I > didn't find the link right now, but you can search on the web, there > was a long discussion about handling this. > Have not checked it recently, so not sure if this got broken somehow. > Please, don't top post. I am not a SD/MMC specialist (I do not feel enough confident in its internals) but the datasheet for 5422 does not mention UHS. However it mentions "High Speed DDR Mode with 200 MHz clock rate (HS400)". This does not look like UHS... https://www.sdcard.org/developers/overview/bus_speed/ This of course is not a definite proof that 5422 does not support UHS. I am just saying that I couldn't find any information that *it does*. Best regards, Krzysztof ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support 2015-10-14 1:15 ` Krzysztof Kozlowski @ 2015-10-14 1:40 ` Jaehoon Chung 2015-10-14 1:52 ` Krzysztof Kozlowski 2015-10-14 2:13 ` Alim Akhtar 1 sibling, 1 reply; 50+ messages in thread From: Jaehoon Chung @ 2015-10-14 1:40 UTC (permalink / raw) To: Krzysztof Kozlowski, Alim Akhtar Cc: Anand Moon, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-samsung-soc@vger.kernel.org, Linux Kernel, Douglas Anderson On 10/14/2015 10:15 AM, Krzysztof Kozlowski wrote: > On 14.10.2015 10:06, Alim Akhtar wrote: >> +Doug >> Hello, >> AFAIR, dw_mmc host controller does support UHS-I [1], specially SDR50 >> and SDR104 modes. >> >> [1]: http://www.spinics.net/lists/linux-mmc/msg28186.html >> >> What I remember is, one need to set "broken-cd" property also in order >> to make it work because of the vqmmc and vmmc connection on board. I >> didn't find the link right now, but you can search on the web, there >> was a long discussion about handling this. >> Have not checked it recently, so not sure if this got broken somehow. >> > > Please, don't top post. > > I am not a SD/MMC specialist (I do not feel enough confident in its > internals) but the datasheet for 5422 does not mention UHS. However it > mentions "High Speed DDR Mode with 200 MHz clock rate (HS400)". This > does not look like UHS... You're right. It's not UHS mode. it mentions eMMC's HS400 mode. UHS and HS400 are difference mode. eMMC mode are supported > https://www.sdcard.org/developers/overview/bus_speed/ > This of course is not a definite proof that 5422 does not support UHS. I > am just saying that I couldn't find any information that *it does*. Well, I think you want to know whether it supported or not. Then you can find the information at User manual. In mobile storage part of User manual, it described the overview. Mobile storage host supports these specification: - Secure Digital memory (SD memory version 3.0) - Secure Digital I/O SDIO (SDIO version 3.0) - etc... SD3.0 is supported UHS-I mode. If user manual of exynos5422 is mentioned this specification, it should be supported UHS-I mode. If my understanding is wrong, let me know, plz. Best Regards, Jaehoon Chung > > Best regards, > Krzysztof > > ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support 2015-10-14 1:40 ` Jaehoon Chung @ 2015-10-14 1:52 ` Krzysztof Kozlowski 2015-10-14 2:08 ` Alim Akhtar 0 siblings, 1 reply; 50+ messages in thread From: Krzysztof Kozlowski @ 2015-10-14 1:52 UTC (permalink / raw) To: Jaehoon Chung, Alim Akhtar Cc: Anand Moon, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-samsung-soc@vger.kernel.org, Linux Kernel, Douglas Anderson On 14.10.2015 10:40, Jaehoon Chung wrote: > On 10/14/2015 10:15 AM, Krzysztof Kozlowski wrote: >> On 14.10.2015 10:06, Alim Akhtar wrote: >>> +Doug >>> Hello, >>> AFAIR, dw_mmc host controller does support UHS-I [1], specially SDR50 >>> and SDR104 modes. >>> >>> [1]: http://www.spinics.net/lists/linux-mmc/msg28186.html >>> >>> What I remember is, one need to set "broken-cd" property also in order >>> to make it work because of the vqmmc and vmmc connection on board. I >>> didn't find the link right now, but you can search on the web, there >>> was a long discussion about handling this. >>> Have not checked it recently, so not sure if this got broken somehow. >>> >> >> Please, don't top post. >> >> I am not a SD/MMC specialist (I do not feel enough confident in its >> internals) but the datasheet for 5422 does not mention UHS. However it >> mentions "High Speed DDR Mode with 200 MHz clock rate (HS400)". This >> does not look like UHS... > > You're right. It's not UHS mode. it mentions eMMC's HS400 mode. > UHS and HS400 are difference mode. > > eMMC mode are supported > >> https://www.sdcard.org/developers/overview/bus_speed/ >> This of course is not a definite proof that 5422 does not support UHS. I >> am just saying that I couldn't find any information that *it does*. > > Well, I think you want to know whether it supported or not. > Then you can find the information at User manual. > In mobile storage part of User manual, it described the overview. > Mobile storage host supports these specification: > - Secure Digital memory (SD memory version 3.0) > - Secure Digital I/O SDIO (SDIO version 3.0) > - etc... > > SD3.0 is supported UHS-I mode. > If user manual of exynos5422 is mentioned this specification, it should be supported UHS-I mode. Thanks! Indeed datasheet mentions that supported SD and SDIO is version 3.0 (not 3.01... which seems irrelevant because 3.0 introduced UHS-I, right?). Best regards, Krzysztof ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support 2015-10-14 1:52 ` Krzysztof Kozlowski @ 2015-10-14 2:08 ` Alim Akhtar 0 siblings, 0 replies; 50+ messages in thread From: Alim Akhtar @ 2015-10-14 2:08 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Jaehoon Chung, Anand Moon, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-samsung-soc@vger.kernel.org, Linux Kernel, Douglas Anderson On Wed, Oct 14, 2015 at 7:22 AM, Krzysztof Kozlowski <k.kozlowski@samsung.com> wrote: > On 14.10.2015 10:40, Jaehoon Chung wrote: >> On 10/14/2015 10:15 AM, Krzysztof Kozlowski wrote: >>> On 14.10.2015 10:06, Alim Akhtar wrote: >>>> +Doug >>>> Hello, >>>> AFAIR, dw_mmc host controller does support UHS-I [1], specially SDR50 >>>> and SDR104 modes. >>>> >>>> [1]: http://www.spinics.net/lists/linux-mmc/msg28186.html >>>> >>>> What I remember is, one need to set "broken-cd" property also in order >>>> to make it work because of the vqmmc and vmmc connection on board. I >>>> didn't find the link right now, but you can search on the web, there >>>> was a long discussion about handling this. >>>> Have not checked it recently, so not sure if this got broken somehow. >>>> >>> >>> Please, don't top post. >>> >>> I am not a SD/MMC specialist (I do not feel enough confident in its >>> internals) but the datasheet for 5422 does not mention UHS. However it >>> mentions "High Speed DDR Mode with 200 MHz clock rate (HS400)". This >>> does not look like UHS... >> >> You're right. It's not UHS mode. it mentions eMMC's HS400 mode. >> UHS and HS400 are difference mode. >> >> eMMC mode are supported >> >>> https://www.sdcard.org/developers/overview/bus_speed/ >>> This of course is not a definite proof that 5422 does not support UHS. I >>> am just saying that I couldn't find any information that *it does*. >> >> Well, I think you want to know whether it supported or not. >> Then you can find the information at User manual. >> In mobile storage part of User manual, it described the overview. >> Mobile storage host supports these specification: >> - Secure Digital memory (SD memory version 3.0) >> - Secure Digital I/O SDIO (SDIO version 3.0) >> - etc... >> >> SD3.0 is supported UHS-I mode. >> If user manual of exynos5422 is mentioned this specification, it should be supported UHS-I mode. > > Thanks! Indeed datasheet mentions that supported SD and SDIO is version > 3.0 (not 3.01... which seems irrelevant because 3.0 introduced UHS-I, > right?). > Yes, your understanding is right. SD3.0 does includes UHS-I. > Best regards, > Krzysztof -- Regards, Alim ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support 2015-10-14 1:15 ` Krzysztof Kozlowski 2015-10-14 1:40 ` Jaehoon Chung @ 2015-10-14 2:13 ` Alim Akhtar 2015-10-14 2:20 ` Krzysztof Kozlowski 1 sibling, 1 reply; 50+ messages in thread From: Alim Akhtar @ 2015-10-14 2:13 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Anand Moon, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-samsung-soc@vger.kernel.org, Linux Kernel, Douglas Anderson On Wed, Oct 14, 2015 at 6:45 AM, Krzysztof Kozlowski <k.kozlowski@samsung.com> wrote: > On 14.10.2015 10:06, Alim Akhtar wrote: >> +Doug >> Hello, >> AFAIR, dw_mmc host controller does support UHS-I [1], specially SDR50 >> and SDR104 modes. >> >> [1]: http://www.spinics.net/lists/linux-mmc/msg28186.html >> >> What I remember is, one need to set "broken-cd" property also in order >> to make it work because of the vqmmc and vmmc connection on board. I >> didn't find the link right now, but you can search on the web, there >> was a long discussion about handling this. >> Have not checked it recently, so not sure if this got broken somehow. >> > > Please, don't top post. > I am sorry, but I didn't get this, what is the guide line here??? > I am not a SD/MMC specialist (I do not feel enough confident in its > internals) but the datasheet for 5422 does not mention UHS. However it > mentions "High Speed DDR Mode with 200 MHz clock rate (HS400)". This > does not look like UHS... > https://www.sdcard.org/developers/overview/bus_speed/ > This of course is not a definite proof that 5422 does not support UHS. I > am just saying that I couldn't find any information that *it does*. > > Best regards, > Krzysztof > -- Regards, Alim ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support 2015-10-14 2:13 ` Alim Akhtar @ 2015-10-14 2:20 ` Krzysztof Kozlowski 2015-10-14 2:26 ` Alim Akhtar 0 siblings, 1 reply; 50+ messages in thread From: Krzysztof Kozlowski @ 2015-10-14 2:20 UTC (permalink / raw) To: Alim Akhtar Cc: Anand Moon, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-samsung-soc@vger.kernel.org, Linux Kernel, Douglas Anderson On 14.10.2015 11:13, Alim Akhtar wrote: > On Wed, Oct 14, 2015 at 6:45 AM, Krzysztof Kozlowski > <k.kozlowski@samsung.com> wrote: >> On 14.10.2015 10:06, Alim Akhtar wrote: >>> +Doug >>> Hello, >>> AFAIR, dw_mmc host controller does support UHS-I [1], specially SDR50 >>> and SDR104 modes. >>> >>> [1]: http://www.spinics.net/lists/linux-mmc/msg28186.html >>> >>> What I remember is, one need to set "broken-cd" property also in order >>> to make it work because of the vqmmc and vmmc connection on board. I >>> didn't find the link right now, but you can search on the web, there >>> was a long discussion about handling this. >>> Have not checked it recently, so not sure if this got broken somehow. >>> >> >> Please, don't top post. >> > I am sorry, but I didn't get this, what is the guide line here??? I mean reply inline, under the other person's quote, not above it. And some old, really old joke: A: Because it messes up the order in which people normally read text. Q: Why is top-posting such a bad thing? A: Top-posting. Q: What is the most annoying thing in e-mail? :) Best regards, Krzysztof ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support 2015-10-14 2:20 ` Krzysztof Kozlowski @ 2015-10-14 2:26 ` Alim Akhtar 0 siblings, 0 replies; 50+ messages in thread From: Alim Akhtar @ 2015-10-14 2:26 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Anand Moon, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-samsung-soc@vger.kernel.org, Linux Kernel, Douglas Anderson On Wed, Oct 14, 2015 at 7:50 AM, Krzysztof Kozlowski <k.kozlowski@samsung.com> wrote: > On 14.10.2015 11:13, Alim Akhtar wrote: >> On Wed, Oct 14, 2015 at 6:45 AM, Krzysztof Kozlowski >> <k.kozlowski@samsung.com> wrote: >>> On 14.10.2015 10:06, Alim Akhtar wrote: >>>> +Doug >>>> Hello, >>>> AFAIR, dw_mmc host controller does support UHS-I [1], specially SDR50 >>>> and SDR104 modes. >>>> >>>> [1]: http://www.spinics.net/lists/linux-mmc/msg28186.html >>>> >>>> What I remember is, one need to set "broken-cd" property also in order >>>> to make it work because of the vqmmc and vmmc connection on board. I >>>> didn't find the link right now, but you can search on the web, there >>>> was a long discussion about handling this. >>>> Have not checked it recently, so not sure if this got broken somehow. >>>> >>> >>> Please, don't top post. >>> >> I am sorry, but I didn't get this, what is the guide line here??? > > I mean reply inline, under the other person's quote, not above it. > > And some old, really old joke: > A: Because it messes up the order in which people normally read text. > Q: Why is top-posting such a bad thing? > A: Top-posting. > Q: What is the most annoying thing in e-mail? > > :) > I see..got it..thanks for clarification. > Best regards, > Krzysztof > -- Regards, Alim ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support 2015-10-14 1:06 ` Alim Akhtar 2015-10-14 1:15 ` Krzysztof Kozlowski @ 2015-10-14 22:40 ` Doug Anderson 2015-10-19 10:11 ` Anand Moon 1 sibling, 1 reply; 50+ messages in thread From: Doug Anderson @ 2015-10-14 22:40 UTC (permalink / raw) To: Alim Akhtar Cc: Krzysztof Kozlowski, Anand Moon, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-samsung-soc@vger.kernel.org, Linux Kernel Hi, On Tue, Oct 13, 2015 at 6:06 PM, Alim Akhtar <alim.akhtar@gmail.com> wrote: > +Doug > Hello, > AFAIR, dw_mmc host controller does support UHS-I [1], specially SDR50 > and SDR104 modes. > > [1]: http://www.spinics.net/lists/linux-mmc/msg28186.html > > What I remember is, one need to set "broken-cd" property also in order > to make it work because of the vqmmc and vmmc connection on board. I > didn't find the link right now, but you can search on the web, there > was a long discussion about handling this. > Have not checked it recently, so not sure if this got broken somehow. Right. It _shouldn't_ be possible to add "vmmc/vqmmc" supplies to your DTS (which you do in patch 2/3) and also to use the "gpc2-2" pin for card detect (even if you configure it as a GPIO). Once you add "vmmc/vqmmc" then Linux ought to be turning these regulators off when no card is plugged in. Presumably the "vqmmc" regulator is hooked up to the "VDDQ_MMC2". If you look in the user manual for 5422 you can see that "GPC2[2]/SD_2_CDn" has power domain "VDDQ_MMC2". Thus you really shouldn't be using that pin when vqmmc is off. I think at some point someone claimed that it still worked for them, but nobody could ever explain why. Full discussion at <https://patchwork.kernel.org/patch/4763881/> --- In case it matters, comments on stuff from earlier in the thread: * As people pointed out, exynos5422 certainly supports all these modes (including DDR50) in the SoC. * Just because the SoC supports these modes doesn't mean that the boards do, which is why the SoC .dtsi doesn't include them. Thus, this patch is "right" in that it changes a board-specific file. * As Krzysztof points out this board doesn't "add" support but rather "enables" support. The distinction is subtle. * You might be able to get DDR50 working, but probably better to just start with SDR modes. Previously I never attempted to get DDR50 cards working, so possibly the software needs extra work? -Doug ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support 2015-10-14 22:40 ` Doug Anderson @ 2015-10-19 10:11 ` Anand Moon 2015-10-19 13:43 ` Krzysztof Kozlowski [not found] ` <CANAwSgSd8sHDcmGmck=Em2H5WJzVWM28cbvs9z6CFgpuTY_Juw-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org> 0 siblings, 2 replies; 50+ messages in thread From: Anand Moon @ 2015-10-19 10:11 UTC (permalink / raw) To: Doug Anderson Cc: Alim Akhtar, Krzysztof Kozlowski, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-samsung-soc@vger.kernel.org, Linux Kernel Hi Doug/ Krzysztof , On 15 October 2015 at 04:10, Doug Anderson <dianders@chromium.org> wrote: > Hi, > > On Tue, Oct 13, 2015 at 6:06 PM, Alim Akhtar <alim.akhtar@gmail.com> wrote: >> +Doug >> Hello, >> AFAIR, dw_mmc host controller does support UHS-I [1], specially SDR50 >> and SDR104 modes. >> >> [1]: http://www.spinics.net/lists/linux-mmc/msg28186.html >> >> What I remember is, one need to set "broken-cd" property also in order >> to make it work because of the vqmmc and vmmc connection on board. I >> didn't find the link right now, but you can search on the web, there >> was a long discussion about handling this. >> Have not checked it recently, so not sure if this got broken somehow. > > Right. It _shouldn't_ be possible to add "vmmc/vqmmc" supplies to > your DTS (which you do in patch 2/3) and also to use the "gpc2-2" pin > for card detect (even if you configure it as a GPIO). Once you add > "vmmc/vqmmc" then Linux ought to be turning these regulators off when > no card is plugged in. Presumably the "vqmmc" regulator is hooked up > to the "VDDQ_MMC2". If you look in the user manual for 5422 you can > see that "GPC2[2]/SD_2_CDn" has power domain "VDDQ_MMC2". Thus you > really shouldn't be using that pin when vqmmc is off. I think at some > point someone claimed that it still worked for them, but nobody could > ever explain why. Full discussion at > <https://patchwork.kernel.org/patch/4763881/> > > --- > > In case it matters, comments on stuff from earlier in the thread: > > * As people pointed out, exynos5422 certainly supports all these modes > (including DDR50) in the SoC. > > * Just because the SoC supports these modes doesn't mean that the > boards do, which is why the SoC .dtsi doesn't include them. Thus, > this patch is "right" in that it changes a board-specific file. > > * As Krzysztof points out this board doesn't "add" support but rather > "enables" support. The distinction is subtle. > > * You might be able to get DDR50 working, but probably better to just > start with SDR modes. Previously I never attempted to get DDR50 cards > working, so possibly the software needs extra work? > Thanks for clarifying all the background details on the mmc changes. Here is what I would conclude from the previous mail chain's. 1 Drop the cd-gpios changes. pinctrl-0 changes. 2 Fix the regulator changes for vmmc/vqmmc with disable of regulator-always-on; 3 Drop this UHS-I changes as if now. Is this ok with you. -Anand Moon > > -Doug ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support 2015-10-19 10:11 ` Anand Moon @ 2015-10-19 13:43 ` Krzysztof Kozlowski [not found] ` <CANAwSgSd8sHDcmGmck=Em2H5WJzVWM28cbvs9z6CFgpuTY_Juw-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org> 1 sibling, 0 replies; 50+ messages in thread From: Krzysztof Kozlowski @ 2015-10-19 13:43 UTC (permalink / raw) To: Anand Moon, Doug Anderson Cc: k.kozlowski.k, Alim Akhtar, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-samsung-soc@vger.kernel.org, Linux Kernel W dniu 19.10.2015 o 19:11, Anand Moon pisze: > Hi Doug/ Krzysztof , > > > Thanks for clarifying all the background details on the mmc changes. > > Here is what I would conclude from the previous mail chain's. > > 1 Drop the cd-gpios changes. pinctrl-0 changes. OK > > 2 Fix the regulator changes for vmmc/vqmmc with disable of regulator-always-on; Just fix all the comments for patch 2. > > 3 Drop this UHS-I changes as if now. > > Is this ok with you. It's okay. Best regards, Krzysztof ^ permalink raw reply [flat|nested] 50+ messages in thread
[parent not found: <CANAwSgSd8sHDcmGmck=Em2H5WJzVWM28cbvs9z6CFgpuTY_Juw-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>]
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support [not found] ` <CANAwSgSd8sHDcmGmck=Em2H5WJzVWM28cbvs9z6CFgpuTY_Juw-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org> @ 2015-10-19 15:11 ` Doug Anderson 0 siblings, 0 replies; 50+ messages in thread From: Doug Anderson @ 2015-10-19 15:11 UTC (permalink / raw) To: Anand Moon Cc: Alim Akhtar, Krzysztof Kozlowski, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung, devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org, linux-samsung-soc-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, Linux Kernel Hi, On Mon, Oct 19, 2015 at 3:11 AM, Anand Moon <linux.amoon-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> wrote: > 1 Drop the cd-gpios changes. pinctrl-0 changes. Right. > 2 Fix the regulator changes for vmmc/vqmmc with disable of regulator-always-on; I'm not totally sure I understand. You should need to keep vmmc and vqmmc always on because otherwise you can't do card detection (unless you poll for card detect). > 3 Drop this UHS-I changes as if now. Sounds right. -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support 2015-10-13 23:59 ` Krzysztof Kozlowski 2015-10-14 1:06 ` Alim Akhtar @ 2015-10-14 3:58 ` Anand Moon 2015-10-14 4:18 ` Krzysztof Kozlowski 2015-10-21 10:28 ` Jaehoon Chung 1 sibling, 2 replies; 50+ messages in thread From: Anand Moon @ 2015-10-14 3:58 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung, devicetree, linux-arm-kernel, linux-samsung-soc@vger.kernel.org, Linux Kernel hi Krzysztof, On 14 October 2015 at 05:29, Krzysztof Kozlowski <k.kozlowski@samsung.com> wrote: > On 14.10.2015 01:27, Anand Moon wrote: >> Hi Krzysztof, >> >> On 13 October 2015 at 09:13, Krzysztof Kozlowski >> <k.kozlowski@samsung.com> wrote: >>> >>> On 13.10.2015 12:08, Anand Moon wrote: >>>> Hi Krzysztof, >>>> >>>> On 13 October 2015 at 05:44, Krzysztof Kozlowski >>>> <k.kozlowski@samsung.com> wrote: >>>>> On 13.10.2015 00:32, Anand Moon wrote: >>>>>> Hi Krzysztof, >>>>>> >>>>>> On 12 October 2015 at 11:14, Krzysztof Kozlowski >>>>>> <k.kozlowski@samsung.com> wrote: >>>>>>> On 12.10.2015 00:46, Anand Moon wrote: >>>>>>>> Added support for UHS-I bus speed 50MB/s (SDR50, DDR50) 104MB/s (SDR104) >>>>>>> >>>>>>> This description is not entirely correct. The MMC driver already >>>>>>> supports these UHS speeds (you did not any code) so you rather enabled >>>>>>> it (description of bindings says "is supported"). >>>>>>> >>>>>>> You mentioned DDR50 but I don't see respective property below. >>>>>>> >>>>>>> How do you know that these modes are really supported? I don't know. Can >>>>>>> you convince me? >>>>>> >>>>>> Setting this DDR50 capability give me this error. That's the reason to >>>>>> drop this capability. >>>>> >>>>> But you mentioned it in commit message! "Added support for UHS-I ... >>>>> (DDR50)" >>>>> >>>>> In the same time dropping DDR50 is not an sufficient proof that "SDR50 >>>>> and SDR104 are really supported". >>>>> >>>> >>>> These changes are related to the microSD card capabilities. >>>> So SDR50 have better frequency over DDR50. On the same Sandisk card. >>>> >>>> When the card select the capability for DDR50 >>>> --------------------------------------------------- >>>> [ 4.001477] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot >>>> req 50000000Hz, actual 50000000HZ div = 0) >>>> [ 4.001604] mmc1: new ultra high speed DDR50 SDHC card at address aaaa >>>> [ 4.004505] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >>>> [ 4.009179] mmcblk0: error -110 sending status command, retrying >>>> [ 4.009271] mmcblk0: error -115 sending stop command, original cmd >>>> response 0x900, card status 0x900 >>>> [ 4.009275] mmcblk0: error -84 transferring data, sector 0, nr 8, >>>> cmd response 0x900, card status 0x0 >>>> [ 4.025563] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot >>>> req 400000Hz, actual 396825HZ div = 63) >>>> [ 4.067770] Console: switching to colour frame buffer device 274x77 >>>> [ 4.098782] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot >>>> req 50000000Hz, actual 50000000HZ div = 0) >>>> [ 4.099692] mmc1: tried to reset card >>>> [ 4.101332] mmcblk0: p1 p2 >>>> >>>> >>>> When the card select the capability for SDR50 >>>> --------------------------------------------------------------------------------- >>>> [ 2.439806] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req >>>> 100000000Hz, actual 100000000HZ div = 0) >>>> [ 2.449729] mmc1: new ultra high speed SDR50 SDHC card at address aaaa >>>> [ 2.455984] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >>>> [ 2.461743] mmcblk0: p1 p2 >>>> >>>> Which will relate to better read/write speed. >>> >>> Which is not an answer to my question. To none of my previous questions. >>> >> >> Basically UHS-I capability (sd-uhs-sdr12, sd-uhs-sdr25, sd-uhs-sdr50, >> sd-uhs-sdr104) help tune speed supported for mmc >> >> I have tired to compare the speed on high speed UHS-I vs ultra high >> speed UHS-I using izone utility. >> >> [ 2.572469] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot >> req 50000000Hz, actual 50000000HZ div = 0) >> [ 2.572609] mmc1: new high speed SDHC card at address aaaa >> >> Command line used: ./iozone -L64 -S32 -azecwI -+n -r4k -r64k >> -r128k -s10M -i0 -i1 -i2 -f datafile -Rb out.xls >> Output is in kBytes/sec >> Time Resolution = 0.000001 seconds. >> Processor cache size set to 32 kBytes. >> Processor cache line size set to 64 bytes. >> File stride size set to 17 * record size. >> random >> random bkwd record stride >> kB reclen write rewrite read reread read >> write read rewrite read fwrite frewrite fread >> freread >> 10240 4 1631 0 6556 0 5538 982 >> 10240 64 8828 0 18897 0 17994 303 >> 10240 128 6269 0 20670 0 20128 1096 >> --------------------------------------------------------------------------------------------------------- >> [ 2.613761] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot >> req 100000000Hz, actual 100000000HZ div = 0) >> [ 2.623573] mmc1: new ultra high speed SDR50 SDHC card at address aaaa >> >> Command line used: ./iozone -L64 -S32 -azecwI -+n -r4k -r64k >> -r128k -s10M -i0 -i1 -i2 -f datafile -Rb out.xls >> Output is in kBytes/sec >> Time Resolution = 0.000001 seconds. >> Processor cache size set to 32 kBytes. >> Processor cache line size set to 64 bytes. >> File stride size set to 17 * record size. >> random >> random bkwd record stride >> kB reclen write rewrite read reread read >> write read rewrite read fwrite frewrite fread >> freread >> 10240 4 1809 0 7507 0 5233 859 >> 10240 64 11622 0 31250 0 28072 516 >> 10240 128 4320 0 34417 0 32509 1148 >> >> My observation is that their slight increase in read/write operation. >> >> Hope I have tried to answer you query. If I am wrong please let me know. > > Nope, that did not answer my query. You gave some performance benchmarks > but my question was not about the speed of anything. The question is > (once again): > How do you know that these modes are really supported? > > You are marking the *host* as supporting these modes. Please provide > information that host supports them *really*, not by experimenting "oh, > it seems to work now, maybe it will work always". > > Usually vendors, if their products implement some kind of > specification/protocol, they mark the products as "compatible with XYZ" etc. I found this link from hardkernel website which specify the interface support http://www.hardkernel.com/main/products/prdt_info.php?g_code=G141578491347 Manufacturer Part Number : Sandisk SDSDQAD-016G Interface : UHS-1 SDR50 I don't know much internal specification of the Odroid XU3/XU4 Boards. I am not sure if it will support host will sd-uhs-sdr104, but it will be compatible for sd-uhs-sdr12, sd-uhs-sdr25, sd-uhs-sdr50. -Anand Moon > > Best regards, > Krzysztof ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support 2015-10-14 3:58 ` Anand Moon @ 2015-10-14 4:18 ` Krzysztof Kozlowski 2015-10-21 10:28 ` Jaehoon Chung 1 sibling, 0 replies; 50+ messages in thread From: Krzysztof Kozlowski @ 2015-10-14 4:18 UTC (permalink / raw) To: Anand Moon Cc: Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung, devicetree, linux-arm-kernel, linux-samsung-soc@vger.kernel.org, Linux Kernel On 14.10.2015 12:58, Anand Moon wrote: > hi Krzysztof, > > On 14 October 2015 at 05:29, Krzysztof Kozlowski > <k.kozlowski@samsung.com> wrote: >> On 14.10.2015 01:27, Anand Moon wrote: >>> Hi Krzysztof, >>> >>> On 13 October 2015 at 09:13, Krzysztof Kozlowski >>> <k.kozlowski@samsung.com> wrote: >>>> >>>> On 13.10.2015 12:08, Anand Moon wrote: >>>>> Hi Krzysztof, >>>>> >>>>> On 13 October 2015 at 05:44, Krzysztof Kozlowski >>>>> <k.kozlowski@samsung.com> wrote: >>>>>> On 13.10.2015 00:32, Anand Moon wrote: >>>>>>> Hi Krzysztof, >>>>>>> >>>>>>> On 12 October 2015 at 11:14, Krzysztof Kozlowski >>>>>>> <k.kozlowski@samsung.com> wrote: >>>>>>>> On 12.10.2015 00:46, Anand Moon wrote: >>>>>>>>> Added support for UHS-I bus speed 50MB/s (SDR50, DDR50) 104MB/s (SDR104) >>>>>>>> >>>>>>>> This description is not entirely correct. The MMC driver already >>>>>>>> supports these UHS speeds (you did not any code) so you rather enabled >>>>>>>> it (description of bindings says "is supported"). >>>>>>>> >>>>>>>> You mentioned DDR50 but I don't see respective property below. >>>>>>>> >>>>>>>> How do you know that these modes are really supported? I don't know. Can >>>>>>>> you convince me? >>>>>>> >>>>>>> Setting this DDR50 capability give me this error. That's the reason to >>>>>>> drop this capability. >>>>>> >>>>>> But you mentioned it in commit message! "Added support for UHS-I ... >>>>>> (DDR50)" >>>>>> >>>>>> In the same time dropping DDR50 is not an sufficient proof that "SDR50 >>>>>> and SDR104 are really supported". >>>>>> >>>>> >>>>> These changes are related to the microSD card capabilities. >>>>> So SDR50 have better frequency over DDR50. On the same Sandisk card. >>>>> >>>>> When the card select the capability for DDR50 >>>>> --------------------------------------------------- >>>>> [ 4.001477] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot >>>>> req 50000000Hz, actual 50000000HZ div = 0) >>>>> [ 4.001604] mmc1: new ultra high speed DDR50 SDHC card at address aaaa >>>>> [ 4.004505] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >>>>> [ 4.009179] mmcblk0: error -110 sending status command, retrying >>>>> [ 4.009271] mmcblk0: error -115 sending stop command, original cmd >>>>> response 0x900, card status 0x900 >>>>> [ 4.009275] mmcblk0: error -84 transferring data, sector 0, nr 8, >>>>> cmd response 0x900, card status 0x0 >>>>> [ 4.025563] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot >>>>> req 400000Hz, actual 396825HZ div = 63) >>>>> [ 4.067770] Console: switching to colour frame buffer device 274x77 >>>>> [ 4.098782] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot >>>>> req 50000000Hz, actual 50000000HZ div = 0) >>>>> [ 4.099692] mmc1: tried to reset card >>>>> [ 4.101332] mmcblk0: p1 p2 >>>>> >>>>> >>>>> When the card select the capability for SDR50 >>>>> --------------------------------------------------------------------------------- >>>>> [ 2.439806] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req >>>>> 100000000Hz, actual 100000000HZ div = 0) >>>>> [ 2.449729] mmc1: new ultra high speed SDR50 SDHC card at address aaaa >>>>> [ 2.455984] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >>>>> [ 2.461743] mmcblk0: p1 p2 >>>>> >>>>> Which will relate to better read/write speed. >>>> >>>> Which is not an answer to my question. To none of my previous questions. >>>> >>> >>> Basically UHS-I capability (sd-uhs-sdr12, sd-uhs-sdr25, sd-uhs-sdr50, >>> sd-uhs-sdr104) help tune speed supported for mmc >>> >>> I have tired to compare the speed on high speed UHS-I vs ultra high >>> speed UHS-I using izone utility. >>> >>> [ 2.572469] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot >>> req 50000000Hz, actual 50000000HZ div = 0) >>> [ 2.572609] mmc1: new high speed SDHC card at address aaaa >>> >>> Command line used: ./iozone -L64 -S32 -azecwI -+n -r4k -r64k >>> -r128k -s10M -i0 -i1 -i2 -f datafile -Rb out.xls >>> Output is in kBytes/sec >>> Time Resolution = 0.000001 seconds. >>> Processor cache size set to 32 kBytes. >>> Processor cache line size set to 64 bytes. >>> File stride size set to 17 * record size. >>> random >>> random bkwd record stride >>> kB reclen write rewrite read reread read >>> write read rewrite read fwrite frewrite fread >>> freread >>> 10240 4 1631 0 6556 0 5538 982 >>> 10240 64 8828 0 18897 0 17994 303 >>> 10240 128 6269 0 20670 0 20128 1096 >>> --------------------------------------------------------------------------------------------------------- >>> [ 2.613761] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot >>> req 100000000Hz, actual 100000000HZ div = 0) >>> [ 2.623573] mmc1: new ultra high speed SDR50 SDHC card at address aaaa >>> >>> Command line used: ./iozone -L64 -S32 -azecwI -+n -r4k -r64k >>> -r128k -s10M -i0 -i1 -i2 -f datafile -Rb out.xls >>> Output is in kBytes/sec >>> Time Resolution = 0.000001 seconds. >>> Processor cache size set to 32 kBytes. >>> Processor cache line size set to 64 bytes. >>> File stride size set to 17 * record size. >>> random >>> random bkwd record stride >>> kB reclen write rewrite read reread read >>> write read rewrite read fwrite frewrite fread >>> freread >>> 10240 4 1809 0 7507 0 5233 859 >>> 10240 64 11622 0 31250 0 28072 516 >>> 10240 128 4320 0 34417 0 32509 1148 >>> >>> My observation is that their slight increase in read/write operation. >>> >>> Hope I have tried to answer you query. If I am wrong please let me know. >> >> Nope, that did not answer my query. You gave some performance benchmarks >> but my question was not about the speed of anything. The question is >> (once again): >> How do you know that these modes are really supported? >> >> You are marking the *host* as supporting these modes. Please provide >> information that host supports them *really*, not by experimenting "oh, >> it seems to work now, maybe it will work always". >> >> Usually vendors, if their products implement some kind of >> specification/protocol, they mark the products as "compatible with XYZ" etc. > > I found this link from hardkernel website which specify the interface support > > http://www.hardkernel.com/main/products/prdt_info.php?g_code=G141578491347 > > Manufacturer Part Number : Sandisk SDSDQAD-016G > Interface : UHS-1 SDR50 > > I don't know much internal specification of the Odroid XU3/XU4 Boards. > > I am not sure if it will support host will sd-uhs-sdr104, but it will > be compatible for sd-uhs-sdr12, sd-uhs-sdr25, sd-uhs-sdr50. I can't find how this proofs anything. You can sell an UHS-II card labelled "for ODROID-XU3 and XU4" and it will work fine on Odroid-XU3. Does it mean that Odroid-XU3 supports UHS-II? That UHS-II card will work even on 10-year camera! Of course not in UHS mode... Does it mean that this 10-year old camera supports UHS-II? Of course not because it will work in some HS mode (or even pre-HS). You can label any SD card as "for Odroid XU3" because any card will work... Best regards, Krzysztof ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support 2015-10-14 3:58 ` Anand Moon 2015-10-14 4:18 ` Krzysztof Kozlowski @ 2015-10-21 10:28 ` Jaehoon Chung 1 sibling, 0 replies; 50+ messages in thread From: Jaehoon Chung @ 2015-10-21 10:28 UTC (permalink / raw) To: Anand Moon, Krzysztof Kozlowski Cc: Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, devicetree, linux-arm-kernel, linux-samsung-soc@vger.kernel.org, Linux Kernel Hi, Anand. On 10/14/2015 12:58 PM, Anand Moon wrote: > hi Krzysztof, > > On 14 October 2015 at 05:29, Krzysztof Kozlowski > <k.kozlowski@samsung.com> wrote: >> On 14.10.2015 01:27, Anand Moon wrote: >>> Hi Krzysztof, >>> >>> On 13 October 2015 at 09:13, Krzysztof Kozlowski >>> <k.kozlowski@samsung.com> wrote: >>>> >>>> On 13.10.2015 12:08, Anand Moon wrote: >>>>> Hi Krzysztof, >>>>> >>>>> On 13 October 2015 at 05:44, Krzysztof Kozlowski >>>>> <k.kozlowski@samsung.com> wrote: >>>>>> On 13.10.2015 00:32, Anand Moon wrote: >>>>>>> Hi Krzysztof, >>>>>>> >>>>>>> On 12 October 2015 at 11:14, Krzysztof Kozlowski >>>>>>> <k.kozlowski@samsung.com> wrote: >>>>>>>> On 12.10.2015 00:46, Anand Moon wrote: >>>>>>>>> Added support for UHS-I bus speed 50MB/s (SDR50, DDR50) 104MB/s (SDR104) >>>>>>>> >>>>>>>> This description is not entirely correct. The MMC driver already >>>>>>>> supports these UHS speeds (you did not any code) so you rather enabled >>>>>>>> it (description of bindings says "is supported"). >>>>>>>> >>>>>>>> You mentioned DDR50 but I don't see respective property below. >>>>>>>> >>>>>>>> How do you know that these modes are really supported? I don't know. Can >>>>>>>> you convince me? >>>>>>> >>>>>>> Setting this DDR50 capability give me this error. That's the reason to >>>>>>> drop this capability. >>>>>> >>>>>> But you mentioned it in commit message! "Added support for UHS-I ... >>>>>> (DDR50)" >>>>>> >>>>>> In the same time dropping DDR50 is not an sufficient proof that "SDR50 >>>>>> and SDR104 are really supported". >>>>>> >>>>> >>>>> These changes are related to the microSD card capabilities. >>>>> So SDR50 have better frequency over DDR50. On the same Sandisk card. >>>>> >>>>> When the card select the capability for DDR50 >>>>> --------------------------------------------------- >>>>> [ 4.001477] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot >>>>> req 50000000Hz, actual 50000000HZ div = 0) >>>>> [ 4.001604] mmc1: new ultra high speed DDR50 SDHC card at address aaaa >>>>> [ 4.004505] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >>>>> [ 4.009179] mmcblk0: error -110 sending status command, retrying >>>>> [ 4.009271] mmcblk0: error -115 sending stop command, original cmd >>>>> response 0x900, card status 0x900 >>>>> [ 4.009275] mmcblk0: error -84 transferring data, sector 0, nr 8, >>>>> cmd response 0x900, card status 0x0 >>>>> [ 4.025563] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot >>>>> req 400000Hz, actual 396825HZ div = 63) >>>>> [ 4.067770] Console: switching to colour frame buffer device 274x77 >>>>> [ 4.098782] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot >>>>> req 50000000Hz, actual 50000000HZ div = 0) >>>>> [ 4.099692] mmc1: tried to reset card >>>>> [ 4.101332] mmcblk0: p1 p2 I found this issue that produced on your board. I will send the patch and test DDR50 on your board. Best Regards, Jaehoon Chung >>>>> >>>>> >>>>> When the card select the capability for SDR50 >>>>> --------------------------------------------------------------------------------- >>>>> [ 2.439806] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req >>>>> 100000000Hz, actual 100000000HZ div = 0) >>>>> [ 2.449729] mmc1: new ultra high speed SDR50 SDHC card at address aaaa >>>>> [ 2.455984] mmcblk0: mmc1:aaaa SL32G 29.7 GiB >>>>> [ 2.461743] mmcblk0: p1 p2 >>>>> >>>>> Which will relate to better read/write speed. >>>> >>>> Which is not an answer to my question. To none of my previous questions. >>>> >>> >>> Basically UHS-I capability (sd-uhs-sdr12, sd-uhs-sdr25, sd-uhs-sdr50, >>> sd-uhs-sdr104) help tune speed supported for mmc >>> >>> I have tired to compare the speed on high speed UHS-I vs ultra high >>> speed UHS-I using izone utility. >>> >>> [ 2.572469] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot >>> req 50000000Hz, actual 50000000HZ div = 0) >>> [ 2.572609] mmc1: new high speed SDHC card at address aaaa >>> >>> Command line used: ./iozone -L64 -S32 -azecwI -+n -r4k -r64k >>> -r128k -s10M -i0 -i1 -i2 -f datafile -Rb out.xls >>> Output is in kBytes/sec >>> Time Resolution = 0.000001 seconds. >>> Processor cache size set to 32 kBytes. >>> Processor cache line size set to 64 bytes. >>> File stride size set to 17 * record size. >>> random >>> random bkwd record stride >>> kB reclen write rewrite read reread read >>> write read rewrite read fwrite frewrite fread >>> freread >>> 10240 4 1631 0 6556 0 5538 982 >>> 10240 64 8828 0 18897 0 17994 303 >>> 10240 128 6269 0 20670 0 20128 1096 >>> --------------------------------------------------------------------------------------------------------- >>> [ 2.613761] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot >>> req 100000000Hz, actual 100000000HZ div = 0) >>> [ 2.623573] mmc1: new ultra high speed SDR50 SDHC card at address aaaa >>> >>> Command line used: ./iozone -L64 -S32 -azecwI -+n -r4k -r64k >>> -r128k -s10M -i0 -i1 -i2 -f datafile -Rb out.xls >>> Output is in kBytes/sec >>> Time Resolution = 0.000001 seconds. >>> Processor cache size set to 32 kBytes. >>> Processor cache line size set to 64 bytes. >>> File stride size set to 17 * record size. >>> random >>> random bkwd record stride >>> kB reclen write rewrite read reread read >>> write read rewrite read fwrite frewrite fread >>> freread >>> 10240 4 1809 0 7507 0 5233 859 >>> 10240 64 11622 0 31250 0 28072 516 >>> 10240 128 4320 0 34417 0 32509 1148 >>> >>> My observation is that their slight increase in read/write operation. >>> >>> Hope I have tried to answer you query. If I am wrong please let me know. >> >> Nope, that did not answer my query. You gave some performance benchmarks >> but my question was not about the speed of anything. The question is >> (once again): >> How do you know that these modes are really supported? >> >> You are marking the *host* as supporting these modes. Please provide >> information that host supports them *really*, not by experimenting "oh, >> it seems to work now, maybe it will work always". >> >> Usually vendors, if their products implement some kind of >> specification/protocol, they mark the products as "compatible with XYZ" etc. > > I found this link from hardkernel website which specify the interface support > > http://www.hardkernel.com/main/products/prdt_info.php?g_code=G141578491347 > > Manufacturer Part Number : Sandisk SDSDQAD-016G > Interface : UHS-1 SDR50 > > I don't know much internal specification of the Odroid XU3/XU4 Boards. > > I am not sure if it will support host will sd-uhs-sdr104, but it will > be compatible for sd-uhs-sdr12, sd-uhs-sdr25, sd-uhs-sdr50. > > -Anand Moon > >> >> Best regards, >> Krzysztof > ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 1/3] ARM: dts: exynos5422-odroidxu3: use cd-gpio method to detect sd-card 2015-10-11 15:46 [PATCH 1/3] ARM: dts: exynos5422-odroidxu3: use cd-gpio method to detect sd-card Anand Moon 2015-10-11 15:46 ` [PATCH 2/3] ARM: dts: use vmmc-supply of emmc/sd for exynos5422-odroidxu3 Anand Moon 2015-10-11 15:46 ` [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support Anand Moon @ 2015-10-12 4:29 ` Krzysztof Kozlowski 2015-10-12 4:43 ` Jaehoon Chung 2 siblings, 1 reply; 50+ messages in thread From: Krzysztof Kozlowski @ 2015-10-12 4:29 UTC (permalink / raw) To: Anand Moon, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, Jaehoon Chung Cc: devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel On 12.10.2015 00:46, Anand Moon wrote: > From: Jaehoon Chung <jh80.chung@samsung.com> > > To detect sd-card use the cd-gpio method. > It can decrease the interrupt for detecting sd-card. > > Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> > Signed-off-by: Anand Moon <linux.amoon@gmail.com> > > --- > Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch > --- > arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 4 +++- > 1 file changed, 3 insertions(+), 1 deletion(-) > > diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi > index 1af5bdc..26decbd 100644 > --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi > +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi > @@ -352,8 +352,10 @@ > samsung,dw-mshc-ciu-div = <3>; > samsung,dw-mshc-sdr-timing = <0 4>; > samsung,dw-mshc-ddr-timing = <0 2>; > + cd-gpios = <&gpc2 2 GPIO_ACTIVE_HIGH>; > + cd-inverted; > pinctrl-names = "default"; > - pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>; > + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; Anand, You essentially reverted here af6ad88acbd6 ("ARM: dts: Mux XMMCnDATA[0] pad correctly for Exynos5420 boards"). Why? There is no explanation in the commit message about this. Best regards, Krzysztof ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 1/3] ARM: dts: exynos5422-odroidxu3: use cd-gpio method to detect sd-card 2015-10-12 4:29 ` [PATCH 1/3] ARM: dts: exynos5422-odroidxu3: use cd-gpio method to detect sd-card Krzysztof Kozlowski @ 2015-10-12 4:43 ` Jaehoon Chung 2015-10-12 14:47 ` Anand Moon 0 siblings, 1 reply; 50+ messages in thread From: Jaehoon Chung @ 2015-10-12 4:43 UTC (permalink / raw) To: Krzysztof Kozlowski, Anand Moon, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski Cc: devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel Hi, On 10/12/2015 01:29 PM, Krzysztof Kozlowski wrote: > On 12.10.2015 00:46, Anand Moon wrote: >> From: Jaehoon Chung <jh80.chung@samsung.com> >> >> To detect sd-card use the cd-gpio method. >> It can decrease the interrupt for detecting sd-card. >> >> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> >> Signed-off-by: Anand Moon <linux.amoon@gmail.com> >> >> --- >> Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch >> --- >> arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 4 +++- >> 1 file changed, 3 insertions(+), 1 deletion(-) >> >> diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >> index 1af5bdc..26decbd 100644 >> --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >> +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >> @@ -352,8 +352,10 @@ >> samsung,dw-mshc-ciu-div = <3>; >> samsung,dw-mshc-sdr-timing = <0 4>; >> samsung,dw-mshc-ddr-timing = <0 2>; >> + cd-gpios = <&gpc2 2 GPIO_ACTIVE_HIGH>; >> + cd-inverted; >> pinctrl-names = "default"; >> - pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>; >> + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; Don't do change this. > > Anand, > > You essentially reverted here af6ad88acbd6 ("ARM: dts: Mux XMMCnDATA[0] > pad correctly for Exynos5420 boards"). Why? There is no explanation in > the commit message about this. I don't remember to send the patch relevant to this. Hmm... Well, Is this patch really signed-off by me? Best Regards, Jaehoon Chung > > Best regards, > Krzysztof > > ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 1/3] ARM: dts: exynos5422-odroidxu3: use cd-gpio method to detect sd-card 2015-10-12 4:43 ` Jaehoon Chung @ 2015-10-12 14:47 ` Anand Moon 2015-10-13 0:12 ` Krzysztof Kozlowski 0 siblings, 1 reply; 50+ messages in thread From: Anand Moon @ 2015-10-12 14:47 UTC (permalink / raw) To: Jaehoon Chung, Krzysztof Kozlowski, Anand Moon, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski Cc: devicetree@vger.kernel.org, linux-samsung-soc@vger.kernel.org, linux-kernel@vger.kernel.org, linux-arm-kernel@lists.infradead.org Hi All, On Monday, October 12, 2015 10:14 AM, Jaehoon Chung <jh80.chung@samsung.com> wrote: Hi, On 10/12/2015 01:29 PM, Krzysztof Kozlowski wrote: > On 12.10.2015 00:46, Anand Moon wrote: >> From: Jaehoon Chung <jh80.chung@samsung.com> >> >> To detect sd-card use the cd-gpio method. >> It can decrease the interrupt for detecting sd-card. >> >> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> >> Signed-off-by: Anand Moon <linux.amoon@gmail.com> >> >> --- >> Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch >> --- >> arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 4 +++- >> 1 file changed, 3 insertions(+), 1 deletion(-) >> >> diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >> index 1af5bdc..26decbd 100644 >> --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >> +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi >> @@ -352,8 +352,10 @@ >> samsung,dw-mshc-ciu-div = <3>; >> samsung,dw-mshc-sdr-timing = <0 4>; >> samsung,dw-mshc-ddr-timing = <0 2>; >> + cd-gpios = <&gpc2 2 GPIO_ACTIVE_HIGH>; >> + cd-inverted; >> pinctrl-names = "default"; >> - pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>; >> + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; Don't do change this. > > Anand, > > You essentially reverted here af6ad88acbd6 ("ARM: dts: Mux XMMCnDATA[0] > pad correctly for Exynos5420 boards"). Why? There is no explanation in > the commit message about this. I don't remember to send the patch relevant to this. Hmm... Well, Is this patch really signed-off by me? Best Regards, Jaehoon Chung > > Best regards, > Krzysztof > > Some how I don't receive these mail on my email id. I have picked up these changes from tizen repository for OdroidXU3. I have tested with this changes to detect UHS-I micro cd cards. That's the reason for this email. If it's wrong then I will drop it. -Anand Moon _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 1/3] ARM: dts: exynos5422-odroidxu3: use cd-gpio method to detect sd-card 2015-10-12 14:47 ` Anand Moon @ 2015-10-13 0:12 ` Krzysztof Kozlowski [not found] ` <561C4C88.2040004-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> 2015-10-13 2:41 ` Anand Moon 0 siblings, 2 replies; 50+ messages in thread From: Krzysztof Kozlowski @ 2015-10-13 0:12 UTC (permalink / raw) To: Anand Moon, Jaehoon Chung, Anand Moon, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski Cc: devicetree@vger.kernel.org, linux-samsung-soc@vger.kernel.org, linux-kernel@vger.kernel.org, linux-arm-kernel@lists.infradead.org On 12.10.2015 23:47, Anand Moon wrote: >> >> Anand, >> >> You essentially reverted here af6ad88acbd6 ("ARM: dts: Mux XMMCnDATA[0] >> pad correctly for Exynos5420 boards"). Why? There is no explanation in >> the commit message about this. > > I don't remember to send the patch relevant to this. Hmm... > Well, Is this patch really signed-off by me? > > Best Regards, > > Jaehoon Chung >> >> Best regards, >> Krzysztof >> > >> > > > Some how I don't receive these mail on my email id. > > I have picked up these changes from tizen repository for OdroidXU3. > I have tested with this changes to detect UHS-I micro cd cards. > That's the reason for this email. ... and you applied it blindly without looking at actual existing contents and at previous commits. That is not how patches from different repositories should be cherry picked. Best regards, Krzysztof ^ permalink raw reply [flat|nested] 50+ messages in thread
[parent not found: <561C4C88.2040004-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>]
* Re: [PATCH 1/3] ARM: dts: exynos5422-odroidxu3: use cd-gpio method to detect sd-card [not found] ` <561C4C88.2040004-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> @ 2015-10-13 2:06 ` Jaehoon Chung 2015-10-13 3:21 ` Anand Moon [not found] ` <561C6713.1070508-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> 0 siblings, 2 replies; 50+ messages in thread From: Jaehoon Chung @ 2015-10-13 2:06 UTC (permalink / raw) To: Krzysztof Kozlowski, Anand Moon, Anand Moon, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-samsung-soc-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org Dear, Anand. On 10/13/2015 09:12 AM, Krzysztof Kozlowski wrote: > On 12.10.2015 23:47, Anand Moon wrote: >>> >>> Anand, >>> >>> You essentially reverted here af6ad88acbd6 ("ARM: dts: Mux XMMCnDATA[0] >>> pad correctly for Exynos5420 boards"). Why? There is no explanation in >>> the commit message about this. >> >> I don't remember to send the patch relevant to this. Hmm... >> Well, Is this patch really signed-off by me? >> >> Best Regards, >> >> Jaehoon Chung >>> >>> Best regards, >>> Krzysztof >>> >> >>> >> >> >> Some how I don't receive these mail on my email id. >> >> I have picked up these changes from tizen repository for OdroidXU3. >> I have tested with this changes to detect UHS-I micro cd cards. >> That's the reason for this email. It seems to make manually, right? I have checked the tizen repository. The below is --- a/arch/arm/boot/dts/exynos5422-odroidxu3.dts +++ b/arch/arm/boot/dts/exynos5422-odroidxu3.dts @@ -335,7 +335,9 @@ samsung,dw-mshc-sdr-timing = <0 4>; samsung,dw-mshc-ddr-timing = <0 2>; pinctrl-names = "default"; - pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>; + cd-gpios = <&gpc2 2 0>; + cd-inverted; + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus1 &sd2_bus4>; bus-width = <4>; cap-sd-highspeed; }; Yours --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi @@ -352,8 +352,10 @@ samsung,dw-mshc-ciu-div = <3>; samsung,dw-mshc-sdr-timing = <0 4>; samsung,dw-mshc-ddr-timing = <0 2>; + cd-gpios = <&gpc2 2 GPIO_ACTIVE_HIGH>; + cd-inverted; pinctrl-names = "default"; - pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>; + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; Did you know what differ? :) Best Regards, Jaehoon Chung > > ... and you applied it blindly without looking at actual existing > contents and at previous commits. > > That is not how patches from different repositories should be cherry picked. > > Best regards, > Krzysztof > > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 1/3] ARM: dts: exynos5422-odroidxu3: use cd-gpio method to detect sd-card 2015-10-13 2:06 ` Jaehoon Chung @ 2015-10-13 3:21 ` Anand Moon [not found] ` <561C6713.1070508-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> 1 sibling, 0 replies; 50+ messages in thread From: Anand Moon @ 2015-10-13 3:21 UTC (permalink / raw) To: Jaehoon Chung Cc: Krzysztof Kozlowski, Anand Moon, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, devicetree@vger.kernel.org, linux-samsung-soc@vger.kernel.org, linux-kernel@vger.kernel.org, linux-arm-kernel@lists.infradead.org Hi Jaehoon Chung, On 13 October 2015 at 07:36, Jaehoon Chung <jh80.chung@samsung.com> wrote: > Dear, Anand. > > > On 10/13/2015 09:12 AM, Krzysztof Kozlowski wrote: >> On 12.10.2015 23:47, Anand Moon wrote: >>>> >>>> Anand, >>>> >>>> You essentially reverted here af6ad88acbd6 ("ARM: dts: Mux XMMCnDATA[0] >>>> pad correctly for Exynos5420 boards"). Why? There is no explanation in >>>> the commit message about this. >>> >>> I don't remember to send the patch relevant to this. Hmm... >>> Well, Is this patch really signed-off by me? >>> >>> Best Regards, >>> >>> Jaehoon Chung >>>> >>>> Best regards, >>>> Krzysztof >>>> >>> >>>> >>> >>> >>> Some how I don't receive these mail on my email id. >>> >>> I have picked up these changes from tizen repository for OdroidXU3. >>> I have tested with this changes to detect UHS-I micro cd cards. >>> That's the reason for this email. > > It seems to make manually, right? > I have checked the tizen repository. > > The below is > > --- a/arch/arm/boot/dts/exynos5422-odroidxu3.dts > +++ b/arch/arm/boot/dts/exynos5422-odroidxu3.dts > @@ -335,7 +335,9 @@ > samsung,dw-mshc-sdr-timing = <0 4>; > samsung,dw-mshc-ddr-timing = <0 2>; > pinctrl-names = "default"; > - pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>; > + cd-gpios = <&gpc2 2 0>; > + cd-inverted; > + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus1 &sd2_bus4>; > bus-width = <4>; > cap-sd-highspeed; > }; > > > > Yours > > --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi > +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi > @@ -352,8 +352,10 @@ > samsung,dw-mshc-ciu-div = <3>; > samsung,dw-mshc-sdr-timing = <0 4>; > samsung,dw-mshc-ddr-timing = <0 2>; > + cd-gpios = <&gpc2 2 GPIO_ACTIVE_HIGH>; > + cd-inverted; > pinctrl-names = "default"; > - pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>; > + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; > > Did you know what differ? :) > My mistake, I will drop the changes. Sorry for the whole mess. -Anand Moon > Best Regards, > Jaehoon Chung > >> >> ... and you applied it blindly without looking at actual existing >> contents and at previous commits. >> >> That is not how patches from different repositories should be cherry picked. >> >> Best regards, >> Krzysztof >> >> > ^ permalink raw reply [flat|nested] 50+ messages in thread
[parent not found: <561C6713.1070508-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>]
* Re: [PATCH 1/3] ARM: dts: exynos5422-odroidxu3: use cd-gpio method to detect sd-card [not found] ` <561C6713.1070508-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> @ 2015-10-13 4:07 ` Anand Moon 0 siblings, 0 replies; 50+ messages in thread From: Anand Moon @ 2015-10-13 4:07 UTC (permalink / raw) To: Jaehoon Chung Cc: Krzysztof Kozlowski, Anand Moon, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-samsung-soc-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org Hi Jaehoon, On 13 October 2015 at 07:36, Jaehoon Chung <jh80.chung-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> wrote: > Dear, Anand. > > > On 10/13/2015 09:12 AM, Krzysztof Kozlowski wrote: >> On 12.10.2015 23:47, Anand Moon wrote: >>>> >>>> Anand, >>>> >>>> You essentially reverted here af6ad88acbd6 ("ARM: dts: Mux XMMCnDATA[0] >>>> pad correctly for Exynos5420 boards"). Why? There is no explanation in >>>> the commit message about this. >>> >>> I don't remember to send the patch relevant to this. Hmm... >>> Well, Is this patch really signed-off by me? >>> >>> Best Regards, >>> >>> Jaehoon Chung >>>> >>>> Best regards, >>>> Krzysztof >>>> >>> >>>> >>> >>> >>> Some how I don't receive these mail on my email id. >>> >>> I have picked up these changes from tizen repository for OdroidXU3. >>> I have tested with this changes to detect UHS-I micro cd cards. >>> That's the reason for this email. > > It seems to make manually, right? > I have checked the tizen repository. > > The below is > > --- a/arch/arm/boot/dts/exynos5422-odroidxu3.dts > +++ b/arch/arm/boot/dts/exynos5422-odroidxu3.dts > @@ -335,7 +335,9 @@ > samsung,dw-mshc-sdr-timing = <0 4>; > samsung,dw-mshc-ddr-timing = <0 2>; > pinctrl-names = "default"; > - pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>; > + cd-gpios = <&gpc2 2 0>; > + cd-inverted; > + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus1 &sd2_bus4>; > bus-width = <4>; > cap-sd-highspeed; > }; > > > > Yours > > --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi > +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi > @@ -352,8 +352,10 @@ > samsung,dw-mshc-ciu-div = <3>; > samsung,dw-mshc-sdr-timing = <0 4>; > samsung,dw-mshc-ddr-timing = <0 2>; > + cd-gpios = <&gpc2 2 GPIO_ACTIVE_HIGH>; > + cd-inverted; > pinctrl-names = "default"; > - pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>; > + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; > > Did you know what differ? :) > > Best Regards, > Jaehoon Chung > >> >> ... and you applied it blindly without looking at actual existing >> contents and at previous commits. >> >> That is not how patches from different repositories should be cherry picked. >> >> Best regards, >> Krzysztof >> >> > Looks like my changes have introduce another bug so please ignore this changes. -Anand Moon -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 50+ messages in thread
* Re: [PATCH 1/3] ARM: dts: exynos5422-odroidxu3: use cd-gpio method to detect sd-card 2015-10-13 0:12 ` Krzysztof Kozlowski [not found] ` <561C4C88.2040004-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org> @ 2015-10-13 2:41 ` Anand Moon 1 sibling, 0 replies; 50+ messages in thread From: Anand Moon @ 2015-10-13 2:41 UTC (permalink / raw) To: Krzysztof Kozlowski Cc: Anand Moon, Jaehoon Chung, Kukjin Kim, Javier Martinez Canillas, Lukasz Majewski, devicetree@vger.kernel.org, linux-samsung-soc@vger.kernel.org, linux-kernel@vger.kernel.org, linux-arm-kernel@lists.infradead.org Hi Krzysztof, On 13 October 2015 at 05:42, Krzysztof Kozlowski <k.kozlowski@samsung.com> wrote: > On 12.10.2015 23:47, Anand Moon wrote: >>> >>> Anand, >>> >>> You essentially reverted here af6ad88acbd6 ("ARM: dts: Mux XMMCnDATA[0] >>> pad correctly for Exynos5420 boards"). Why? There is no explanation in >>> the commit message about this. >> >> I don't remember to send the patch relevant to this. Hmm... >> Well, Is this patch really signed-off by me? >> >> Best Regards, >> >> Jaehoon Chung >>> >>> Best regards, >>> Krzysztof >>> >> >>> >> >> >> Some how I don't receive these mail on my email id. >> >> I have picked up these changes from tizen repository for OdroidXU3. >> I have tested with this changes to detect UHS-I micro cd cards. >> That's the reason for this email. > > ... and you applied it blindly without looking at actual existing > contents and at previous commits. > > That is not how patches from different repositories should be cherry picked. Sorry But I did not change it right way. By looking at the diff. If the changes are wrong I will drop that changes. I have to dig in my logs to find out why I have changes this setting. Here is the log below, I will check If I am able to reproduce this bug in the current kernel. Sorry for the mess I have created. --------------------------------------------------------------------------------------- Oct 6 08:23:21 odroidxu4 kernel: [ 6.559940] ====================================================== Oct 6 08:23:21 odroidxu4 kernel: [ 6.559943] [ INFO: possible circular locking dependency detected ] Oct 6 08:23:21 odroidxu4 kernel: [ 6.559947] 4.2.0-xu4hkdn #7 Not tainted Oct 6 08:23:21 odroidxu4 kernel: [ 6.559950] ------------------------------------------------------- Oct 6 08:23:21 odroidxu4 kernel: [ 6.559954] swapper/0/1 is trying to acquire lock: Oct 6 08:23:21 odroidxu4 kernel: [ 6.559972] (&map->mutex){+.+...}, at: [<c04a9414>] regmap_lock_mutex+0x1c/0x20 Oct 6 08:23:21 odroidxu4 kernel: [ 6.559975] Oct 6 08:23:21 odroidxu4 kernel: [ 6.559975] but task is already holding lock: Oct 6 08:23:21 odroidxu4 kernel: [ 6.559987] (prepare_lock){+.+.+.}, at: [<c05b468c>] clk_prepare_lock+0x20/0x108 Oct 6 08:23:21 odroidxu4 kernel: [ 6.559990] Oct 6 08:23:21 odroidxu4 kernel: [ 6.559990] which lock already depends on the new lock. Oct 6 08:23:21 odroidxu4 kernel: [ 6.559990] Oct 6 08:23:21 odroidxu4 kernel: [ 6.559993] Oct 6 08:23:21 odroidxu4 kernel: [ 6.559993] the existing dependency chain (in reverse order) is: Oct 6 08:23:21 odroidxu4 kernel: [ 6.560004] Oct 6 08:23:21 odroidxu4 kernel: [ 6.560004] -> #1 (prepare_lock){+.+.+.}: Oct 6 08:23:21 odroidxu4 kernel: [ 6.560019] [<c06b90d0>] mutex_lock_nested+0x84/0x4e4 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560026] [<c05b46cc>] clk_prepare_lock+0x60/0x108 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560033] [<c05b84a8>] clk_unprepare+0x28/0x38 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560044] [<c0542ba8>] exynos5_i2c_xfer+0x2dc/0x3a4 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560051] [<c053e1b4>] __i2c_transfer+0x160/0xc60 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560057] [<c053ed28>] i2c_transfer+0x74/0xa0 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560065] [<c04b2be4>] regmap_i2c_read+0x58/0x74 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560072] [<c04ac38c>] _regmap_raw_read+0x130/0x654 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560078] [<c04ac8e4>] _regmap_bus_read+0x34/0x6c Oct 6 08:23:21 odroidxu4 kernel: [ 6.560083] [<c04ab350>] _regmap_read+0x7c/0x350 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560090] [<c04ab674>] regmap_read+0x50/0x70 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560100] [<c04043a0>] regulator_is_enabled_regmap+0x30/0xa4 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560107] [<c03ff73c>] _regulator_is_enabled.part.10+0x2c/0x38 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560113] [<c04000c4>] _regulator_do_set_voltage+0x720/0x9d0 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560119] [<c0400438>] regulator_set_voltage+0xc4/0x150 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560129] [<c0589d6c>] dw_mci_switch_voltage+0x98/0xbc Oct 6 08:23:21 odroidxu4 kernel: [ 6.560136] [<c0570dc0>] mmc_power_up.part.16+0x6c/0x108 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560143] [<c0571e44>] mmc_start_host+0x54/0x78 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560149] [<c0573194>] mmc_add_host+0x6c/0x90 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560156] [<c058ae84>] dw_mci_probe+0x660/0xc98 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560162] [<c058c978>] dw_mci_pltfm_register+0x9c/0xa8 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560168] [<c058d014>] dw_mci_exynos_probe+0x30/0x38 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560176] [<c048de40>] platform_drv_probe+0x54/0xb4 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560183] [<c048b9d8>] driver_probe_device+0x184/0x2c0 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560189] [<c048bbb8>] __driver_attach+0xa4/0xa8 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560195] [<c0489b90>] bus_for_each_dev+0x78/0xac Oct 6 08:23:21 odroidxu4 kernel: [ 6.560202] [<c048b498>] driver_attach+0x2c/0x30 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560208] [<c048b0a4>] bus_add_driver+0x1b0/0x228 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560214] [<c048ce6c>] driver_register+0x88/0x108 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560221] [<c048dd6c>] __platform_driver_register+0x64/0x6c Oct 6 08:23:21 odroidxu4 kernel: [ 6.560229] [<c0995abc>] dw_mci_exynos_pltfm_driver_init+0x1c/0x20 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560237] [<c0009820>] do_one_initcall+0x9c/0x1e8 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560245] [<c095efa8>] kernel_init_freeable+0x250/0x2f4 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560252] [<c06b3774>] kernel_init+0x1c/0xf8 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560259] [<c000fe58>] ret_from_fork+0x14/0x3c Oct 6 08:23:21 odroidxu4 kernel: [ 6.560269] Oct 6 08:23:21 odroidxu4 kernel: [ 6.560269] -> #0 (&map->mutex){+.+...}: Oct 6 08:23:21 odroidxu4 kernel: [ 6.560277] [<c008ac00>] lock_acquire+0x128/0x378 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560284] [<c06b90d0>] mutex_lock_nested+0x84/0x4e4 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560290] [<c04a9414>] regmap_lock_mutex+0x1c/0x20 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560296] [<c04ab664>] regmap_read+0x40/0x70 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560304] [<c05bd62c>] s2mps11_clk_is_prepared+0x30/0x4c Oct 6 08:23:21 odroidxu4 kernel: [ 6.560310] [<c05b4bc8>] clk_unprepare_unused_subtree+0x84/0x564 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560316] [<c05b7940>] clk_disable_unused+0xb8/0x148 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560322] [<c0009820>] do_one_initcall+0x9c/0x1e8 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560328] [<c095efa8>] kernel_init_freeable+0x250/0x2f4 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560334] [<c06b3774>] kernel_init+0x1c/0xf8 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560340] [<c000fe58>] ret_from_fork+0x14/0x3c Oct 6 08:23:21 odroidxu4 kernel: [ 6.560343] Oct 6 08:23:21 odroidxu4 kernel: [ 6.560343] other info that might help us debug this: Oct 6 08:23:21 odroidxu4 kernel: [ 6.560343] Oct 6 08:23:21 odroidxu4 kernel: [ 6.560346] Possible unsafe locking scenario: Oct 6 08:23:21 odroidxu4 kernel: [ 6.560346] Oct 6 08:23:21 odroidxu4 kernel: [ 6.560349] CPU0 CPU1 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560351] ---- ---- Oct 6 08:23:21 odroidxu4 kernel: [ 6.560358] lock(prepare_lock); Oct 6 08:23:21 odroidxu4 kernel: [ 6.560365] lock(&map->mutex); Oct 6 08:23:21 odroidxu4 kernel: [ 6.560371] lock(prepare_lock); Oct 6 08:23:21 odroidxu4 kernel: [ 6.560378] lock(&map->mutex); Oct 6 08:23:21 odroidxu4 kernel: [ 6.560380] Oct 6 08:23:21 odroidxu4 kernel: [ 6.560380] *** DEADLOCK *** Oct 6 08:23:21 odroidxu4 kernel: [ 6.560380] Oct 6 08:23:21 odroidxu4 kernel: [ 6.560384] 1 lock held by swapper/0/1: Oct 6 08:23:21 odroidxu4 kernel: [ 6.560397] #0: (prepare_lock){+.+.+.}, at: [<c05b468c>] clk_prepare_lock+0x20/0x108 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560400] Oct 6 08:23:21 odroidxu4 kernel: [ 6.560400] stack backtrace: Oct 6 08:23:21 odroidxu4 kernel: [ 6.560405] CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.2.0-xu4hkdn #7 Oct 6 08:23:21 odroidxu4 kernel: [ 6.560408] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree) Oct 6 08:23:21 odroidxu4 kernel: [ 6.560418] [<c00189bc>] (unwind_backtrace) from [<c0014608>] (show_stack+0x20/0x24) Oct 6 08:23:21 odroidxu4 kernel: [ 6.560424] [<c0014608>] (show_stack) from [<c06b64f8>] (dump_stack+0x8c/0xcc) Oct 6 08:23:21 odroidxu4 kernel: [ 6.560430] [<c06b64f8>] (dump_stack) from [<c0083c34>] (print_circular_bug+0x218/0x340) Oct 6 08:23:21 odroidxu4 kernel: [ 6.560436] [<c0083c34>] (print_circular_bug) from [<c0089d14>] (__lock_acquire+0x1c40/0x227c) Oct 6 08:23:21 odroidxu4 kernel: [ 6.560441] [<c0089d14>] (__lock_acquire) from [<c008ac00>] (lock_acquire+0x128/0x378) Oct 6 08:23:21 odroidxu4 kernel: [ 6.560447] [<c008ac00>] (lock_acquire) from [<c06b90d0>] (mutex_lock_nested+0x84/0x4e4) Oct 6 08:23:21 odroidxu4 kernel: [ 6.560453] [<c06b90d0>] (mutex_lock_nested) from [<c04a9414>] (regmap_lock_mutex+0x1c/0x20) Oct 6 08:23:21 odroidxu4 kernel: [ 6.560458] [<c04a9414>] (regmap_lock_mutex) from [<c04ab664>] (regmap_read+0x40/0x70) Oct 6 08:23:21 odroidxu4 kernel: [ 6.560464] [<c04ab664>] (regmap_read) from [<c05bd62c>] (s2mps11_clk_is_prepared+0x30/0x4c) Oct 6 08:23:21 odroidxu4 kernel: [ 6.560471] [<c05bd62c>] (s2mps11_clk_is_prepared) from [<c05b4bc8>] (clk_unprepare_unused_subtree+0x84/0x564) Oct 6 08:23:21 odroidxu4 kernel: [ 6.560477] [<c05b4bc8>] (clk_unprepare_unused_subtree) from [<c05b7940>] (clk_disable_unused+0xb8/0x148) Oct 6 08:23:21 odroidxu4 kernel: [ 6.560482] [<c05b7940>] (clk_disable_unused) from [<c0009820>] (do_one_initcall+0x9c/0x1e8) Oct 6 08:23:21 odroidxu4 kernel: [ 6.560487] [<c0009820>] (do_one_initcall) from [<c095efa8>] (kernel_init_freeable+0x250/0x2f4) Oct 6 08:23:21 odroidxu4 kernel: [ 6.560493] [<c095efa8>] (kernel_init_freeable) from [<c06b3774>] (kernel_init+0x1c/0xf8) Oct 6 08:23:21 odroidxu4 kernel: [ 6.560498] [<c06b3774>] (kernel_init) from [<c000fe58>] (ret_from_fork+0x14/0x3c) -Anand Moon > > Best regards, > Krzysztof > ^ permalink raw reply [flat|nested] 50+ messages in thread
end of thread, other threads:[~2015-10-21 10:28 UTC | newest]
Thread overview: 50+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2015-10-11 15:46 [PATCH 1/3] ARM: dts: exynos5422-odroidxu3: use cd-gpio method to detect sd-card Anand Moon
2015-10-11 15:46 ` [PATCH 2/3] ARM: dts: use vmmc-supply of emmc/sd for exynos5422-odroidxu3 Anand Moon
2015-10-12 4:42 ` Krzysztof Kozlowski
2015-10-12 5:49 ` Krzysztof Kozlowski
2015-10-12 11:08 ` Anand Moon
2015-10-12 12:13 ` Krzysztof Kozlowski
2015-10-12 14:33 ` Anand Moon
2015-10-13 0:10 ` Krzysztof Kozlowski
2015-10-13 2:29 ` Anand Moon
2015-10-13 2:39 ` Jaehoon Chung
[not found] ` <561C6ED3.4090101-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
2015-10-13 2:45 ` Anand Moon
2015-10-11 15:46 ` [PATCH 3/3] ARM: dts: exynos5422-odroidxu3: Added UHS-I bus speed support Anand Moon
[not found] ` <1444578364-1384-3-git-send-email-linux.amoon-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
2015-10-12 5:44 ` Krzysztof Kozlowski
2015-10-12 10:46 ` Anand Moon
2015-10-12 10:51 ` Jaehoon Chung
2015-10-12 11:23 ` Anand Moon
2015-10-12 12:42 ` Krzysztof Kozlowski
2015-10-12 13:04 ` Jaehoon Chung
2015-10-12 13:16 ` Krzysztof Kozlowski
2015-10-13 2:28 ` Jaehoon Chung
2015-10-12 15:32 ` Anand Moon
2015-10-13 0:14 ` Krzysztof Kozlowski
2015-10-13 3:08 ` Anand Moon
2015-10-13 3:43 ` Krzysztof Kozlowski
[not found] ` <561C7DF1.6000609-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
2015-10-13 3:49 ` Anand Moon
2015-10-13 16:27 ` Anand Moon
2015-10-13 23:59 ` Krzysztof Kozlowski
2015-10-14 1:06 ` Alim Akhtar
2015-10-14 1:15 ` Krzysztof Kozlowski
2015-10-14 1:40 ` Jaehoon Chung
2015-10-14 1:52 ` Krzysztof Kozlowski
2015-10-14 2:08 ` Alim Akhtar
2015-10-14 2:13 ` Alim Akhtar
2015-10-14 2:20 ` Krzysztof Kozlowski
2015-10-14 2:26 ` Alim Akhtar
2015-10-14 22:40 ` Doug Anderson
2015-10-19 10:11 ` Anand Moon
2015-10-19 13:43 ` Krzysztof Kozlowski
[not found] ` <CANAwSgSd8sHDcmGmck=Em2H5WJzVWM28cbvs9z6CFgpuTY_Juw-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2015-10-19 15:11 ` Doug Anderson
2015-10-14 3:58 ` Anand Moon
2015-10-14 4:18 ` Krzysztof Kozlowski
2015-10-21 10:28 ` Jaehoon Chung
2015-10-12 4:29 ` [PATCH 1/3] ARM: dts: exynos5422-odroidxu3: use cd-gpio method to detect sd-card Krzysztof Kozlowski
2015-10-12 4:43 ` Jaehoon Chung
2015-10-12 14:47 ` Anand Moon
2015-10-13 0:12 ` Krzysztof Kozlowski
[not found] ` <561C4C88.2040004-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
2015-10-13 2:06 ` Jaehoon Chung
2015-10-13 3:21 ` Anand Moon
[not found] ` <561C6713.1070508-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
2015-10-13 4:07 ` Anand Moon
2015-10-13 2:41 ` Anand Moon
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).