[PATCH linux-next (v2) 1/3] mtd: brcmnand: Add brcm,bcm6368-nand device tree binding

[PATCH linux-next (v2) 1/3] mtd: brcmnand: Add brcm,bcm6368-nand device tree binding

[Simon Arlott]

Add device tree binding for NAND on the BCM6368.

The BCM6368 has a NAND interrupt register with combined status and enable
registers. It also requires a clock, so add an optional clock to the
common brcmnand binding.

Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
---
Changed "nand-intr-base" reg name to "nand-int-base".

 .../devicetree/bindings/mtd/brcm,brcmnand.txt      | 32 ++++++++++++++++++++++
 1 file changed, 32 insertions(+)

diff --git a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt
index 4ff7128..ebfa6fc 100644
--- a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt
+++ b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt
@@ -45,6 +45,8 @@ Required properties:
 - #size-cells      : <0>
 
 Optional properties:
+- clock                     : reference to the clock for the NAND controller
+- clock-names               : "nand" (required for the above clock)
 - brcm,nand-has-wp          : Some versions of this IP include a write-protect
                               (WP) control bit. It is always available on >=
                               v7.0. Use this property to describe the rare
@@ -72,6 +74,12 @@ we define additional 'compatible' properties and associated register resources w
        and enable registers
      - reg-names: (required) "nand-int-base"
 
+   * "brcm,nand-bcm6368"
+     - compatible: should contain "brcm,nand-bcm<soc>", "brcm,nand-bcm6368"
+     - reg: (required) the 'NAND_INTR_BASE' register range, with combined status
+       and enable registers, and boot address registers
+     - reg-names: (required) "nand-int-base"
+
    * "brcm,nand-iproc"
      - reg: (required) the "IDM" register range, for interrupt enable and APB
        bus access endianness configuration, and the "EXT" register range,
@@ -148,3 +156,27 @@ nand@f0442800 {
 		};
 	};
 };
+
+nand@10000200 {
+	compatible = "brcm,nand-bcm63168", "brcm,nand-bcm6368",
+		"brcm,brcmnand-v4.0", "brcm,brcmnand";
+	reg = <0x10000200 0x180>,
+	      <0x10000600 0x200>,
+	      <0x100000b0 0x10>;
+	reg-names = "nand", "nand-cache", "nand-intr-base";
+	interrupt-parent = <&periph_intc>;
+	interrupts = <50>;
+	clocks = <&periph_clk 20>;
+	clock-names = "nand";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	nand0: nandcs@0 {
+		compatible = "brcm,nandcs";
+		reg = <0>;
+		nand-on-flash-bbt;
+		nand-ecc-strength = <1>;
+		nand-ecc-step-size = <512>;
+	};
+};
-- 
2.1.4

-- 
Simon Arlott

[PATCH linux-next (v2) 2/3] mtd: brcmnand: Request and enable the clock if present

[Simon Arlott]

Attempt to enable a clock named "nand" as some SoCs have a clock for the
controller that needs to be enabled.

Signed-off-by: Simon Arlott <simon-A6De1vDTPLDsq35pWSNszA@public.gmane.org>
---
Resend, no changes.

 drivers/mtd/nand/brcmnand/brcmnand.c | 64 ++++++++++++++++++++++++++++--------
 1 file changed, 50 insertions(+), 14 deletions(-)

diff --git a/drivers/mtd/nand/brcmnand/brcmnand.c b/drivers/mtd/nand/brcmnand/brcmnand.c
index 190a99a..dca8162 100644
--- a/drivers/mtd/nand/brcmnand/brcmnand.c
+++ b/drivers/mtd/nand/brcmnand/brcmnand.c
@@ -11,6 +11,7 @@
  * GNU General Public License for more details.
  */
 
+#include <linux/clk.h>
 #include <linux/version.h>
 #include <linux/module.h>
 #include <linux/init.h>
@@ -122,6 +123,9 @@ struct brcmnand_controller {
 	/* Some SoCs provide custom interrupt status register(s) */
 	struct brcmnand_soc	*soc;
 
+	/* Some SoCs have a gateable clock for the controller */
+	struct clk		*clk;
+
 	int			cmd_pending;
 	bool			dma_pending;
 	struct completion	done;
@@ -2127,10 +2131,24 @@ int brcmnand_probe(struct platform_device *pdev, struct brcmnand_soc *soc)
 	if (IS_ERR(ctrl->nand_base))
 		return PTR_ERR(ctrl->nand_base);
 
+	/* Enable clock before using NAND registers */
+	ctrl->clk = devm_clk_get(dev, "nand");
+	if (!IS_ERR(ctrl->clk)) {
+		ret = clk_prepare_enable(ctrl->clk);
+		if (ret)
+			return ret;
+	} else {
+		ret = PTR_ERR(ctrl->clk);
+		if (ret == -EPROBE_DEFER)
+			return ret;
+
+		ctrl->clk = NULL;
+	}
+
 	/* Initialize NAND revision */
 	ret = brcmnand_revision_init(ctrl);
 	if (ret)
-		return ret;
+		goto err;
 
 	/*
 	 * Most chips have this cache at a fixed offset within 'nand' block.
@@ -2139,8 +2157,10 @@ int brcmnand_probe(struct platform_device *pdev, struct brcmnand_soc *soc)
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "nand-cache");
 	if (res) {
 		ctrl->nand_fc = devm_ioremap_resource(dev, res);
-		if (IS_ERR(ctrl->nand_fc))
-			return PTR_ERR(ctrl->nand_fc);
+		if (IS_ERR(ctrl->nand_fc)) {
+			ret = PTR_ERR(ctrl->nand_fc);
+			goto err;
+		}
 	} else {
 		ctrl->nand_fc = ctrl->nand_base +
 				ctrl->reg_offsets[BRCMNAND_FC_BASE];
@@ -2150,8 +2170,10 @@ int brcmnand_probe(struct platform_device *pdev, struct brcmnand_soc *soc)
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "flash-dma");
 	if (res) {
 		ctrl->flash_dma_base = devm_ioremap_resource(dev, res);
-		if (IS_ERR(ctrl->flash_dma_base))
-			return PTR_ERR(ctrl->flash_dma_base);
+		if (IS_ERR(ctrl->flash_dma_base)) {
+			ret = PTR_ERR(ctrl->flash_dma_base);
+			goto err;
+		}
 
 		flash_dma_writel(ctrl, FLASH_DMA_MODE, 1); /* linked-list */
 		flash_dma_writel(ctrl, FLASH_DMA_ERROR_STATUS, 0);
@@ -2160,13 +2182,16 @@ int brcmnand_probe(struct platform_device *pdev, struct brcmnand_soc *soc)
 		ctrl->dma_desc = dmam_alloc_coherent(dev,
 						     sizeof(*ctrl->dma_desc),
 						     &ctrl->dma_pa, GFP_KERNEL);
-		if (!ctrl->dma_desc)
-			return -ENOMEM;
+		if (!ctrl->dma_desc) {
+			ret = -ENOMEM;
+			goto err;
+		}
 
 		ctrl->dma_irq = platform_get_irq(pdev, 1);
 		if ((int)ctrl->dma_irq < 0) {
 			dev_err(dev, "missing FLASH_DMA IRQ\n");
-			return -ENODEV;
+			ret = -ENODEV;
+			goto err;
 		}
 
 		ret = devm_request_irq(dev, ctrl->dma_irq,
@@ -2175,7 +2200,7 @@ int brcmnand_probe(struct platform_device *pdev, struct brcmnand_soc *soc)
 		if (ret < 0) {
 			dev_err(dev, "can't allocate IRQ %d: error %d\n",
 					ctrl->dma_irq, ret);
-			return ret;
+			goto err;
 		}
 
 		dev_info(dev, "enabling FLASH_DMA\n");
@@ -2199,7 +2224,8 @@ int brcmnand_probe(struct platform_device *pdev, struct brcmnand_soc *soc)
 	ctrl->irq = platform_get_irq(pdev, 0);
 	if ((int)ctrl->irq < 0) {
 		dev_err(dev, "no IRQ defined\n");
-		return -ENODEV;
+		ret = -ENODEV;
+		goto err;
 	}
 
 	/*
@@ -2223,7 +2249,7 @@ int brcmnand_probe(struct platform_device *pdev, struct brcmnand_soc *soc)
 	if (ret < 0) {
 		dev_err(dev, "can't allocate IRQ %d: error %d\n",
 			ctrl->irq, ret);
-		return ret;
+		goto err;
 	}
 
 	for_each_available_child_of_node(dn, child) {
@@ -2233,7 +2259,8 @@ int brcmnand_probe(struct platform_device *pdev, struct brcmnand_soc *soc)
 			host = devm_kzalloc(dev, sizeof(*host), GFP_KERNEL);
 			if (!host) {
 				of_node_put(child);
-				return -ENOMEM;
+				ret = -ENOMEM;
+				goto err;
 			}
 			host->pdev = pdev;
 			host->ctrl = ctrl;
@@ -2249,10 +2276,17 @@ int brcmnand_probe(struct platform_device *pdev, struct brcmnand_soc *soc)
 	}
 
 	/* No chip-selects could initialize properly */
-	if (list_empty(&ctrl->host_list))
-		return -ENODEV;
+	if (list_empty(&ctrl->host_list)) {
+		ret = -ENODEV;
+		goto err;
+	}
 
 	return 0;
+
+err:
+	clk_disable_unprepare(ctrl->clk);
+	return ret;
+
 }
 EXPORT_SYMBOL_GPL(brcmnand_probe);
 
@@ -2264,6 +2298,8 @@ int brcmnand_remove(struct platform_device *pdev)
 	list_for_each_entry(host, &ctrl->host_list, node)
 		nand_release(&host->mtd);
 
+	clk_disable_unprepare(ctrl->clk);
+
 	dev_set_drvdata(&pdev->dev, NULL);
 
 	return 0;
-- 
2.1.4

-- 
Simon Arlott
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH linux-next (v2) 2/3] mtd: brcmnand: Request and enable the clock if present

[Florian Fainelli]

Le 09/12/2015 12:42, Simon Arlott a écrit :
> Attempt to enable a clock named "nand" as some SoCs have a clock for the
> controller that needs to be enabled.
> 
> Signed-off-by: Simon Arlott <simon-A6De1vDTPLDsq35pWSNszA@public.gmane.org>

Reviewed-by: Florian Fainelli <f.fainelli-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

> ---
> Resend, no changes.
> 
>  drivers/mtd/nand/brcmnand/brcmnand.c | 64 ++++++++++++++++++++++++++++--------
>  1 file changed, 50 insertions(+), 14 deletions(-)
> 
> diff --git a/drivers/mtd/nand/brcmnand/brcmnand.c b/drivers/mtd/nand/brcmnand/brcmnand.c
> index 190a99a..dca8162 100644
> --- a/drivers/mtd/nand/brcmnand/brcmnand.c
> +++ b/drivers/mtd/nand/brcmnand/brcmnand.c
> @@ -11,6 +11,7 @@
>   * GNU General Public License for more details.
>   */
>  
> +#include <linux/clk.h>
>  #include <linux/version.h>
>  #include <linux/module.h>
>  #include <linux/init.h>
> @@ -122,6 +123,9 @@ struct brcmnand_controller {
>  	/* Some SoCs provide custom interrupt status register(s) */
>  	struct brcmnand_soc	*soc;
>  
> +	/* Some SoCs have a gateable clock for the controller */
> +	struct clk		*clk;
> +
>  	int			cmd_pending;
>  	bool			dma_pending;
>  	struct completion	done;
> @@ -2127,10 +2131,24 @@ int brcmnand_probe(struct platform_device *pdev, struct brcmnand_soc *soc)
>  	if (IS_ERR(ctrl->nand_base))
>  		return PTR_ERR(ctrl->nand_base);
>  
> +	/* Enable clock before using NAND registers */
> +	ctrl->clk = devm_clk_get(dev, "nand");
> +	if (!IS_ERR(ctrl->clk)) {
> +		ret = clk_prepare_enable(ctrl->clk);
> +		if (ret)
> +			return ret;
> +	} else {
> +		ret = PTR_ERR(ctrl->clk);
> +		if (ret == -EPROBE_DEFER)
> +			return ret;
> +
> +		ctrl->clk = NULL;
> +	}
> +
>  	/* Initialize NAND revision */
>  	ret = brcmnand_revision_init(ctrl);
>  	if (ret)
> -		return ret;
> +		goto err;
>  
>  	/*
>  	 * Most chips have this cache at a fixed offset within 'nand' block.
> @@ -2139,8 +2157,10 @@ int brcmnand_probe(struct platform_device *pdev, struct brcmnand_soc *soc)
>  	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "nand-cache");
>  	if (res) {
>  		ctrl->nand_fc = devm_ioremap_resource(dev, res);
> -		if (IS_ERR(ctrl->nand_fc))
> -			return PTR_ERR(ctrl->nand_fc);
> +		if (IS_ERR(ctrl->nand_fc)) {
> +			ret = PTR_ERR(ctrl->nand_fc);
> +			goto err;
> +		}
>  	} else {
>  		ctrl->nand_fc = ctrl->nand_base +
>  				ctrl->reg_offsets[BRCMNAND_FC_BASE];
> @@ -2150,8 +2170,10 @@ int brcmnand_probe(struct platform_device *pdev, struct brcmnand_soc *soc)
>  	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "flash-dma");
>  	if (res) {
>  		ctrl->flash_dma_base = devm_ioremap_resource(dev, res);
> -		if (IS_ERR(ctrl->flash_dma_base))
> -			return PTR_ERR(ctrl->flash_dma_base);
> +		if (IS_ERR(ctrl->flash_dma_base)) {
> +			ret = PTR_ERR(ctrl->flash_dma_base);
> +			goto err;
> +		}
>  
>  		flash_dma_writel(ctrl, FLASH_DMA_MODE, 1); /* linked-list */
>  		flash_dma_writel(ctrl, FLASH_DMA_ERROR_STATUS, 0);
> @@ -2160,13 +2182,16 @@ int brcmnand_probe(struct platform_device *pdev, struct brcmnand_soc *soc)
>  		ctrl->dma_desc = dmam_alloc_coherent(dev,
>  						     sizeof(*ctrl->dma_desc),
>  						     &ctrl->dma_pa, GFP_KERNEL);
> -		if (!ctrl->dma_desc)
> -			return -ENOMEM;
> +		if (!ctrl->dma_desc) {
> +			ret = -ENOMEM;
> +			goto err;
> +		}
>  
>  		ctrl->dma_irq = platform_get_irq(pdev, 1);
>  		if ((int)ctrl->dma_irq < 0) {
>  			dev_err(dev, "missing FLASH_DMA IRQ\n");
> -			return -ENODEV;
> +			ret = -ENODEV;
> +			goto err;
>  		}
>  
>  		ret = devm_request_irq(dev, ctrl->dma_irq,
> @@ -2175,7 +2200,7 @@ int brcmnand_probe(struct platform_device *pdev, struct brcmnand_soc *soc)
>  		if (ret < 0) {
>  			dev_err(dev, "can't allocate IRQ %d: error %d\n",
>  					ctrl->dma_irq, ret);
> -			return ret;
> +			goto err;
>  		}
>  
>  		dev_info(dev, "enabling FLASH_DMA\n");
> @@ -2199,7 +2224,8 @@ int brcmnand_probe(struct platform_device *pdev, struct brcmnand_soc *soc)
>  	ctrl->irq = platform_get_irq(pdev, 0);
>  	if ((int)ctrl->irq < 0) {
>  		dev_err(dev, "no IRQ defined\n");
> -		return -ENODEV;
> +		ret = -ENODEV;
> +		goto err;
>  	}
>  
>  	/*
> @@ -2223,7 +2249,7 @@ int brcmnand_probe(struct platform_device *pdev, struct brcmnand_soc *soc)
>  	if (ret < 0) {
>  		dev_err(dev, "can't allocate IRQ %d: error %d\n",
>  			ctrl->irq, ret);
> -		return ret;
> +		goto err;
>  	}
>  
>  	for_each_available_child_of_node(dn, child) {
> @@ -2233,7 +2259,8 @@ int brcmnand_probe(struct platform_device *pdev, struct brcmnand_soc *soc)
>  			host = devm_kzalloc(dev, sizeof(*host), GFP_KERNEL);
>  			if (!host) {
>  				of_node_put(child);
> -				return -ENOMEM;
> +				ret = -ENOMEM;
> +				goto err;
>  			}
>  			host->pdev = pdev;
>  			host->ctrl = ctrl;
> @@ -2249,10 +2276,17 @@ int brcmnand_probe(struct platform_device *pdev, struct brcmnand_soc *soc)
>  	}
>  
>  	/* No chip-selects could initialize properly */
> -	if (list_empty(&ctrl->host_list))
> -		return -ENODEV;
> +	if (list_empty(&ctrl->host_list)) {
> +		ret = -ENODEV;
> +		goto err;
> +	}
>  
>  	return 0;
> +
> +err:
> +	clk_disable_unprepare(ctrl->clk);
> +	return ret;
> +
>  }
>  EXPORT_SYMBOL_GPL(brcmnand_probe);
>  
> @@ -2264,6 +2298,8 @@ int brcmnand_remove(struct platform_device *pdev)
>  	list_for_each_entry(host, &ctrl->host_list, node)
>  		nand_release(&host->mtd);
>  
> +	clk_disable_unprepare(ctrl->clk);
> +
>  	dev_set_drvdata(&pdev->dev, NULL);
>  
>  	return 0;
> 


-- 
Florian
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH linux-next (v2) 3/3] mtd: brcmnand: Add support for the BCM6368

[Simon Arlott]

The BCM6368 has a NAND interrupt register with combined status and enable
registers.

As the BCM6328, BCM6362 and BCM6368 all use v2.1 controllers, the first
variant that will work with this driver is the BCM63268 using a v4.0
controller.

Set up the device by disabling and acking all interrupts, then handle
the CTRL_READY interrupt.

Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
---
Changed "nand-intr-base" reg name to "nand-int-base".

 drivers/mtd/nand/brcmnand/Makefile       |   1 +
 drivers/mtd/nand/brcmnand/bcm6368_nand.c | 145 +++++++++++++++++++++++++++++++
 2 files changed, 146 insertions(+)
 create mode 100644 drivers/mtd/nand/brcmnand/bcm6368_nand.c

diff --git a/drivers/mtd/nand/brcmnand/Makefile b/drivers/mtd/nand/brcmnand/Makefile
index 3b1fbfd..b28ffb59 100644
--- a/drivers/mtd/nand/brcmnand/Makefile
+++ b/drivers/mtd/nand/brcmnand/Makefile
@@ -2,5 +2,6 @@
 # more specific iproc_nand.o, for instance
 obj-$(CONFIG_MTD_NAND_BRCMNAND)		+= iproc_nand.o
 obj-$(CONFIG_MTD_NAND_BRCMNAND)		+= bcm63138_nand.o
+obj-$(CONFIG_MTD_NAND_BRCMNAND)		+= bcm6368_nand.o
 obj-$(CONFIG_MTD_NAND_BRCMNAND)		+= brcmstb_nand.o
 obj-$(CONFIG_MTD_NAND_BRCMNAND)		+= brcmnand.o
diff --git a/drivers/mtd/nand/brcmnand/bcm6368_nand.c b/drivers/mtd/nand/brcmnand/bcm6368_nand.c
new file mode 100644
index 0000000..7f5359b
--- /dev/null
+++ b/drivers/mtd/nand/brcmnand/bcm6368_nand.c
@@ -0,0 +1,145 @@
+/*
+ * Copyright 2015 Simon Arlott
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Derived from bcm63138_nand.c:
+ * Copyright © 2015 Broadcom Corporation
+ *
+ * Derived from bcm963xx_4.12L.06B_consumer/shared/opensource/include/bcm963xx/63268_map_part.h:
+ * Copyright 2000-2010 Broadcom Corporation
+ *
+ * Derived from bcm963xx_4.12L.06B_consumer/shared/opensource/flash/nandflash.c:
+ * Copyright 2000-2010 Broadcom Corporation
+ */
+
+#include <linux/device.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#include "brcmnand.h"
+
+struct bcm6368_nand_soc {
+	struct brcmnand_soc soc;
+	void __iomem *base;
+};
+
+#define BCM6368_NAND_INT		0x00
+#define  BCM6368_NAND_STATUS_SHIFT	0
+#define  BCM6368_NAND_STATUS_MASK	(0xfff << BCM6368_NAND_STATUS_SHIFT)
+#define  BCM6368_NAND_ENABLE_SHIFT	16
+#define  BCM6368_NAND_ENABLE_MASK	(0xffff << BCM6368_NAND_ENABLE_SHIFT)
+#define BCM6368_NAND_BASE_ADDR0	0x04
+#define BCM6368_NAND_BASE_ADDR1	0x0c
+
+enum {
+	BCM6368_NP_READ		= BIT(0),
+	BCM6368_BLOCK_ERASE	= BIT(1),
+	BCM6368_COPY_BACK	= BIT(2),
+	BCM6368_PAGE_PGM	= BIT(3),
+	BCM6368_CTRL_READY	= BIT(4),
+	BCM6368_DEV_RBPIN	= BIT(5),
+	BCM6368_ECC_ERR_UNC	= BIT(6),
+	BCM6368_ECC_ERR_CORR	= BIT(7),
+};
+
+static bool bcm6368_nand_intc_ack(struct brcmnand_soc *soc)
+{
+	struct bcm6368_nand_soc *priv =
+			container_of(soc, struct bcm6368_nand_soc, soc);
+	void __iomem *mmio = priv->base + BCM6368_NAND_INT;
+	u32 val = brcmnand_readl(mmio);
+
+	if (val & (BCM6368_CTRL_READY << BCM6368_NAND_STATUS_SHIFT)) {
+		/* Ack interrupt */
+		val &= ~BCM6368_NAND_STATUS_MASK;
+		val |= BCM6368_CTRL_READY << BCM6368_NAND_STATUS_SHIFT;
+		brcmnand_writel(val, mmio);
+		return true;
+	}
+
+	return false;
+}
+
+static void bcm6368_nand_intc_set(struct brcmnand_soc *soc, bool en)
+{
+	struct bcm6368_nand_soc *priv =
+			container_of(soc, struct bcm6368_nand_soc, soc);
+	void __iomem *mmio = priv->base + BCM6368_NAND_INT;
+	u32 val = brcmnand_readl(mmio);
+
+	/* Don't ack any interrupts */
+	val &= ~BCM6368_NAND_STATUS_MASK;
+
+	if (en)
+		val |= BCM6368_CTRL_READY << BCM6368_NAND_ENABLE_SHIFT;
+	else
+		val &= ~(BCM6368_CTRL_READY << BCM6368_NAND_ENABLE_SHIFT);
+
+	brcmnand_writel(val, mmio);
+}
+
+static int bcm6368_nand_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct bcm6368_nand_soc *priv;
+	struct brcmnand_soc *soc;
+	struct resource *res;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+	soc = &priv->soc;
+
+	res = platform_get_resource_byname(pdev,
+		IORESOURCE_MEM, "nand-int-base");
+	if (!res)
+		return -EINVAL;
+
+	priv->base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(priv->base))
+		return PTR_ERR(priv->base);
+
+	soc->ctlrdy_ack = bcm6368_nand_intc_ack;
+	soc->ctlrdy_set_enabled = bcm6368_nand_intc_set;
+
+	/* Disable and ack all interrupts  */
+	brcmnand_writel(0, priv->base + BCM6368_NAND_INT);
+	brcmnand_writel(BCM6368_NAND_STATUS_MASK,
+			priv->base + BCM6368_NAND_INT);
+
+	return brcmnand_probe(pdev, soc);
+}
+
+static const struct of_device_id bcm6368_nand_of_match[] = {
+	{ .compatible = "brcm,nand-bcm6368" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, bcm6368_nand_of_match);
+
+static struct platform_driver bcm6368_nand_driver = {
+	.probe			= bcm6368_nand_probe,
+	.remove			= brcmnand_remove,
+	.driver = {
+		.name		= "bcm6368_nand",
+		.pm		= &brcmnand_pm_ops,
+		.of_match_table	= bcm6368_nand_of_match,
+	}
+};
+module_platform_driver(bcm6368_nand_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Simon Arlott");
+MODULE_DESCRIPTION("NAND driver for BCM6368");
-- 
2.1.4

-- 
Simon Arlott

Re: [PATCH linux-next (v2) 3/3] mtd: brcmnand: Add support for the BCM6368

[Florian Fainelli]

Le 09/12/2015 12:43, Simon Arlott a écrit :
> The BCM6368 has a NAND interrupt register with combined status and enable
> registers.
> 
> As the BCM6328, BCM6362 and BCM6368 all use v2.1 controllers, the first
> variant that will work with this driver is the BCM63268 using a v4.0
> controller.
> 
> Set up the device by disabling and acking all interrupts, then handle
> the CTRL_READY interrupt.
> 
> Signed-off-by: Simon Arlott <simon-A6De1vDTPLDsq35pWSNszA@public.gmane.org>

Reviewed-by: Florian Fainelli <f.fainelli-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

> ---
> Changed "nand-intr-base" reg name to "nand-int-base".
> 
>  drivers/mtd/nand/brcmnand/Makefile       |   1 +
>  drivers/mtd/nand/brcmnand/bcm6368_nand.c | 145 +++++++++++++++++++++++++++++++
>  2 files changed, 146 insertions(+)
>  create mode 100644 drivers/mtd/nand/brcmnand/bcm6368_nand.c
> 
> diff --git a/drivers/mtd/nand/brcmnand/Makefile b/drivers/mtd/nand/brcmnand/Makefile
> index 3b1fbfd..b28ffb59 100644
> --- a/drivers/mtd/nand/brcmnand/Makefile
> +++ b/drivers/mtd/nand/brcmnand/Makefile
> @@ -2,5 +2,6 @@
>  # more specific iproc_nand.o, for instance
>  obj-$(CONFIG_MTD_NAND_BRCMNAND)		+= iproc_nand.o
>  obj-$(CONFIG_MTD_NAND_BRCMNAND)		+= bcm63138_nand.o
> +obj-$(CONFIG_MTD_NAND_BRCMNAND)		+= bcm6368_nand.o
>  obj-$(CONFIG_MTD_NAND_BRCMNAND)		+= brcmstb_nand.o
>  obj-$(CONFIG_MTD_NAND_BRCMNAND)		+= brcmnand.o
> diff --git a/drivers/mtd/nand/brcmnand/bcm6368_nand.c b/drivers/mtd/nand/brcmnand/bcm6368_nand.c
> new file mode 100644
> index 0000000..7f5359b
> --- /dev/null
> +++ b/drivers/mtd/nand/brcmnand/bcm6368_nand.c
> @@ -0,0 +1,145 @@
> +/*
> + * Copyright 2015 Simon Arlott
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Derived from bcm63138_nand.c:
> + * Copyright © 2015 Broadcom Corporation
> + *
> + * Derived from bcm963xx_4.12L.06B_consumer/shared/opensource/include/bcm963xx/63268_map_part.h:
> + * Copyright 2000-2010 Broadcom Corporation
> + *
> + * Derived from bcm963xx_4.12L.06B_consumer/shared/opensource/flash/nandflash.c:
> + * Copyright 2000-2010 Broadcom Corporation
> + */
> +
> +#include <linux/device.h>
> +#include <linux/io.h>
> +#include <linux/ioport.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/platform_device.h>
> +#include <linux/slab.h>
> +
> +#include "brcmnand.h"
> +
> +struct bcm6368_nand_soc {
> +	struct brcmnand_soc soc;
> +	void __iomem *base;
> +};
> +
> +#define BCM6368_NAND_INT		0x00
> +#define  BCM6368_NAND_STATUS_SHIFT	0
> +#define  BCM6368_NAND_STATUS_MASK	(0xfff << BCM6368_NAND_STATUS_SHIFT)
> +#define  BCM6368_NAND_ENABLE_SHIFT	16
> +#define  BCM6368_NAND_ENABLE_MASK	(0xffff << BCM6368_NAND_ENABLE_SHIFT)
> +#define BCM6368_NAND_BASE_ADDR0	0x04
> +#define BCM6368_NAND_BASE_ADDR1	0x0c
> +
> +enum {
> +	BCM6368_NP_READ		= BIT(0),
> +	BCM6368_BLOCK_ERASE	= BIT(1),
> +	BCM6368_COPY_BACK	= BIT(2),
> +	BCM6368_PAGE_PGM	= BIT(3),
> +	BCM6368_CTRL_READY	= BIT(4),
> +	BCM6368_DEV_RBPIN	= BIT(5),
> +	BCM6368_ECC_ERR_UNC	= BIT(6),
> +	BCM6368_ECC_ERR_CORR	= BIT(7),
> +};
> +
> +static bool bcm6368_nand_intc_ack(struct brcmnand_soc *soc)
> +{
> +	struct bcm6368_nand_soc *priv =
> +			container_of(soc, struct bcm6368_nand_soc, soc);
> +	void __iomem *mmio = priv->base + BCM6368_NAND_INT;
> +	u32 val = brcmnand_readl(mmio);
> +
> +	if (val & (BCM6368_CTRL_READY << BCM6368_NAND_STATUS_SHIFT)) {
> +		/* Ack interrupt */
> +		val &= ~BCM6368_NAND_STATUS_MASK;
> +		val |= BCM6368_CTRL_READY << BCM6368_NAND_STATUS_SHIFT;
> +		brcmnand_writel(val, mmio);
> +		return true;
> +	}
> +
> +	return false;
> +}
> +
> +static void bcm6368_nand_intc_set(struct brcmnand_soc *soc, bool en)
> +{
> +	struct bcm6368_nand_soc *priv =
> +			container_of(soc, struct bcm6368_nand_soc, soc);
> +	void __iomem *mmio = priv->base + BCM6368_NAND_INT;
> +	u32 val = brcmnand_readl(mmio);
> +
> +	/* Don't ack any interrupts */
> +	val &= ~BCM6368_NAND_STATUS_MASK;
> +
> +	if (en)
> +		val |= BCM6368_CTRL_READY << BCM6368_NAND_ENABLE_SHIFT;
> +	else
> +		val &= ~(BCM6368_CTRL_READY << BCM6368_NAND_ENABLE_SHIFT);
> +
> +	brcmnand_writel(val, mmio);
> +}
> +
> +static int bcm6368_nand_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct bcm6368_nand_soc *priv;
> +	struct brcmnand_soc *soc;
> +	struct resource *res;
> +
> +	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> +	if (!priv)
> +		return -ENOMEM;
> +	soc = &priv->soc;
> +
> +	res = platform_get_resource_byname(pdev,
> +		IORESOURCE_MEM, "nand-int-base");
> +	if (!res)
> +		return -EINVAL;
> +
> +	priv->base = devm_ioremap_resource(dev, res);
> +	if (IS_ERR(priv->base))
> +		return PTR_ERR(priv->base);
> +
> +	soc->ctlrdy_ack = bcm6368_nand_intc_ack;
> +	soc->ctlrdy_set_enabled = bcm6368_nand_intc_set;
> +
> +	/* Disable and ack all interrupts  */
> +	brcmnand_writel(0, priv->base + BCM6368_NAND_INT);
> +	brcmnand_writel(BCM6368_NAND_STATUS_MASK,
> +			priv->base + BCM6368_NAND_INT);
> +
> +	return brcmnand_probe(pdev, soc);
> +}
> +
> +static const struct of_device_id bcm6368_nand_of_match[] = {
> +	{ .compatible = "brcm,nand-bcm6368" },
> +	{},
> +};
> +MODULE_DEVICE_TABLE(of, bcm6368_nand_of_match);
> +
> +static struct platform_driver bcm6368_nand_driver = {
> +	.probe			= bcm6368_nand_probe,
> +	.remove			= brcmnand_remove,
> +	.driver = {
> +		.name		= "bcm6368_nand",
> +		.pm		= &brcmnand_pm_ops,
> +		.of_match_table	= bcm6368_nand_of_match,
> +	}
> +};
> +module_platform_driver(bcm6368_nand_driver);
> +
> +MODULE_LICENSE("GPL");
> +MODULE_AUTHOR("Simon Arlott");
> +MODULE_DESCRIPTION("NAND driver for BCM6368");
> 


-- 
Florian
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH linux-next (v2) 1/3] mtd: brcmnand: Add brcm,bcm6368-nand device tree binding

[Florian Fainelli]

Le 09/12/2015 12:40, Simon Arlott a écrit :
> Add device tree binding for NAND on the BCM6368.
> 
> The BCM6368 has a NAND interrupt register with combined status and enable
> registers. It also requires a clock, so add an optional clock to the
> common brcmnand binding.
> 

Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>

> Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
> ---
> Changed "nand-intr-base" reg name to "nand-int-base".
> 
>  .../devicetree/bindings/mtd/brcm,brcmnand.txt      | 32 ++++++++++++++++++++++
>  1 file changed, 32 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt
> index 4ff7128..ebfa6fc 100644
> --- a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt
> +++ b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt
> @@ -45,6 +45,8 @@ Required properties:
>  - #size-cells      : <0>
>  
>  Optional properties:
> +- clock                     : reference to the clock for the NAND controller
> +- clock-names               : "nand" (required for the above clock)
>  - brcm,nand-has-wp          : Some versions of this IP include a write-protect
>                                (WP) control bit. It is always available on >=
>                                v7.0. Use this property to describe the rare
> @@ -72,6 +74,12 @@ we define additional 'compatible' properties and associated register resources w
>         and enable registers
>       - reg-names: (required) "nand-int-base"
>  
> +   * "brcm,nand-bcm6368"
> +     - compatible: should contain "brcm,nand-bcm<soc>", "brcm,nand-bcm6368"
> +     - reg: (required) the 'NAND_INTR_BASE' register range, with combined status
> +       and enable registers, and boot address registers
> +     - reg-names: (required) "nand-int-base"
> +
>     * "brcm,nand-iproc"
>       - reg: (required) the "IDM" register range, for interrupt enable and APB
>         bus access endianness configuration, and the "EXT" register range,
> @@ -148,3 +156,27 @@ nand@f0442800 {
>  		};
>  	};
>  };
> +
> +nand@10000200 {
> +	compatible = "brcm,nand-bcm63168", "brcm,nand-bcm6368",
> +		"brcm,brcmnand-v4.0", "brcm,brcmnand";
> +	reg = <0x10000200 0x180>,
> +	      <0x10000600 0x200>,
> +	      <0x100000b0 0x10>;
> +	reg-names = "nand", "nand-cache", "nand-intr-base";
> +	interrupt-parent = <&periph_intc>;
> +	interrupts = <50>;
> +	clocks = <&periph_clk 20>;
> +	clock-names = "nand";
> +
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +
> +	nand0: nandcs@0 {
> +		compatible = "brcm,nandcs";
> +		reg = <0>;
> +		nand-on-flash-bbt;
> +		nand-ecc-strength = <1>;
> +		nand-ecc-step-size = <512>;
> +	};
> +};
> 


-- 
Florian

Re: [PATCH linux-next (v2) 1/3] mtd: brcmnand: Add brcm,bcm6368-nand device tree binding

[Brian Norris]

On Wed, Dec 09, 2015 at 01:01:42PM -0800, Florian Fainelli wrote:
> Le 09/12/2015 12:40, Simon Arlott a écrit :
> > Add device tree binding for NAND on the BCM6368.
> > 
> > The BCM6368 has a NAND interrupt register with combined status and enable
> > registers. It also requires a clock, so add an optional clock to the
> > common brcmnand binding.
> > 
> 
> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>

Applied this and patches 2 and 3 to l2-mtd.git, with one small fix,
below.

> > Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
> > ---
> > Changed "nand-intr-base" reg name to "nand-int-base".
> > 
> >  .../devicetree/bindings/mtd/brcm,brcmnand.txt      | 32 ++++++++++++++++++++++
> >  1 file changed, 32 insertions(+)
> > 
> > diff --git a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt
> > index 4ff7128..ebfa6fc 100644
> > --- a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt
> > +++ b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt
> > @@ -45,6 +45,8 @@ Required properties:
> >  - #size-cells      : <0>
> >  
> >  Optional properties:
> > +- clock                     : reference to the clock for the NAND controller
> > +- clock-names               : "nand" (required for the above clock)
> >  - brcm,nand-has-wp          : Some versions of this IP include a write-protect
> >                                (WP) control bit. It is always available on >=
> >                                v7.0. Use this property to describe the rare
> > @@ -72,6 +74,12 @@ we define additional 'compatible' properties and associated register resources w
> >         and enable registers
> >       - reg-names: (required) "nand-int-base"
> >  
> > +   * "brcm,nand-bcm6368"
> > +     - compatible: should contain "brcm,nand-bcm<soc>", "brcm,nand-bcm6368"
> > +     - reg: (required) the 'NAND_INTR_BASE' register range, with combined status
> > +       and enable registers, and boot address registers
> > +     - reg-names: (required) "nand-int-base"
> > +
> >     * "brcm,nand-iproc"
> >       - reg: (required) the "IDM" register range, for interrupt enable and APB
> >         bus access endianness configuration, and the "EXT" register range,
> > @@ -148,3 +156,27 @@ nand@f0442800 {
> >  		};
> >  	};
> >  };
> > +
> > +nand@10000200 {
> > +	compatible = "brcm,nand-bcm63168", "brcm,nand-bcm6368",
> > +		"brcm,brcmnand-v4.0", "brcm,brcmnand";
> > +	reg = <0x10000200 0x180>,
> > +	      <0x10000600 0x200>,
> > +	      <0x100000b0 0x10>;
> > +	reg-names = "nand", "nand-cache", "nand-intr-base";

s/intr/int/

> > +	interrupt-parent = <&periph_intc>;
> > +	interrupts = <50>;
> > +	clocks = <&periph_clk 20>;
> > +	clock-names = "nand";
> > +
> > +	#address-cells = <1>;
> > +	#size-cells = <0>;
> > +
> > +	nand0: nandcs@0 {
> > +		compatible = "brcm,nandcs";
> > +		reg = <0>;
> > +		nand-on-flash-bbt;
> > +		nand-ecc-strength = <1>;
> > +		nand-ecc-step-size = <512>;
> > +	};
> > +};
> > 
> 
> 
> -- 
> Florian