* [PATCH linux-next (v3) 2/2] reset: bcm6345: Add support for the BCM6345 soft-reset controller
[not found] ` <5669EE86.8030406-qdVf85lJwsCyrPCCpiK2c/XRex20P6io@public.gmane.org>
@ 2015-12-10 21:34 ` Simon Arlott
2015-12-11 3:47 ` [PATCH linux-next (v3) 1/2] reset: Add brcm,bcm6345-reset device tree binding Rob Herring
1 sibling, 0 replies; 4+ messages in thread
From: Simon Arlott @ 2015-12-10 21:34 UTC (permalink / raw)
To: Philipp Zabel, Kevin Cernekee, Florian Fainelli,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: linux-kernel-u79uwXL29TY76Z2rM5mHXA, MIPS Mailing List,
Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell,
Sergei Shtylyov, Jonas Gorski
The BCM6345 contains a soft-reset controller activated by setting
a bit (that must previously have been cleared).
Signed-off-by: Simon Arlott <simon-A6De1vDTPLDsq35pWSNszA@public.gmane.org>
---
v3: Resend based on linux-next, no changes.
v2: Renamed to bcm6345, removed "mask" property (and the regmap register
size is always assumed to be 32 bits).
Moved from drivers/reset/ to drivers/reset/bcm/.
MAINTAINERS | 1 +
drivers/reset/Kconfig | 1 +
drivers/reset/Makefile | 17 +++---
drivers/reset/bcm/Kconfig | 10 ++++
drivers/reset/bcm/Makefile | 1 +
drivers/reset/bcm/reset-bcm6345.c | 109 ++++++++++++++++++++++++++++++++++++++
6 files changed, 131 insertions(+), 8 deletions(-)
create mode 100644 drivers/reset/bcm/Kconfig
create mode 100644 drivers/reset/bcm/Makefile
create mode 100644 drivers/reset/bcm/reset-bcm6345.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 9b54ddc..b81b238 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2393,6 +2393,7 @@ F: drivers/clk/bcm/clk-bcm6345*
F: drivers/irqchip/irq-bcm63*
F: drivers/irqchip/irq-bcm7*
F: drivers/irqchip/irq-brcmstb*
+F: drivers/reset/bcm/reset-bcm6345*
F: include/linux/bcm63xx_wdt.h
BROADCOM TG3 GIGABIT ETHERNET DRIVER
diff --git a/drivers/reset/Kconfig b/drivers/reset/Kconfig
index 0615f50..ee73f5f 100644
--- a/drivers/reset/Kconfig
+++ b/drivers/reset/Kconfig
@@ -12,4 +12,5 @@ menuconfig RESET_CONTROLLER
If unsure, say no.
+source "drivers/reset/bcm/Kconfig"
source "drivers/reset/sti/Kconfig"
diff --git a/drivers/reset/Makefile b/drivers/reset/Makefile
index 85d5904..a34f469 100644
--- a/drivers/reset/Makefile
+++ b/drivers/reset/Makefile
@@ -1,8 +1,9 @@
-obj-$(CONFIG_RESET_CONTROLLER) += core.o
-obj-$(CONFIG_ARCH_LPC18XX) += reset-lpc18xx.o
-obj-$(CONFIG_ARCH_SOCFPGA) += reset-socfpga.o
-obj-$(CONFIG_ARCH_BERLIN) += reset-berlin.o
-obj-$(CONFIG_ARCH_SUNXI) += reset-sunxi.o
-obj-$(CONFIG_ARCH_STI) += sti/
-obj-$(CONFIG_ARCH_ZYNQ) += reset-zynq.o
-obj-$(CONFIG_ATH79) += reset-ath79.o
+obj-$(CONFIG_RESET_CONTROLLER) += core.o
+obj-$(CONFIG_ARCH_LPC18XX) += reset-lpc18xx.o
+obj-$(CONFIG_ARCH_SOCFPGA) += reset-socfpga.o
+obj-$(CONFIG_ARCH_BERLIN) += reset-berlin.o
+obj-$(CONFIG_ARCH_SUNXI) += reset-sunxi.o
+obj-$(CONFIG_ARCH_STI) += sti/
+obj-$(CONFIG_ARCH_ZYNQ) += reset-zynq.o
+obj-$(CONFIG_ATH79) += reset-ath79.o
+obj-y += bcm/
diff --git a/drivers/reset/bcm/Kconfig b/drivers/reset/bcm/Kconfig
new file mode 100644
index 0000000..85931c9
--- /dev/null
+++ b/drivers/reset/bcm/Kconfig
@@ -0,0 +1,10 @@
+if RESET_CONTROLLER
+
+config RESET_BCM6345
+ bool "BCM6345 Reset Controller"
+ depends on BMIPS_GENERIC
+ default BMIPS_GENERIC
+ help
+ Support resetting of devices on BCM6345 boards.
+
+endif
diff --git a/drivers/reset/bcm/Makefile b/drivers/reset/bcm/Makefile
new file mode 100644
index 0000000..3d004bd
--- /dev/null
+++ b/drivers/reset/bcm/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_RESET_BCM6345) += reset-bcm6345.o
diff --git a/drivers/reset/bcm/reset-bcm6345.c b/drivers/reset/bcm/reset-bcm6345.c
new file mode 100644
index 0000000..a95433d
--- /dev/null
+++ b/drivers/reset/bcm/reset-bcm6345.c
@@ -0,0 +1,109 @@
+/*
+ * Copyright 2015 Simon Arlott
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ *
+ * Derived from reset-berlin.c:
+ * Copyright (C) 2014 Marvell Technology Group Ltd.
+ *
+ * Antoine Tenart <antoine.tenart-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
+ * Sebastian Hesselbarth <sebastian.hesselbarth-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
+ */
+
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/reset-controller.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+
+#define to_bcm6345_reset_priv(p) \
+ container_of((p), struct bcm6345_reset_priv, rcdev)
+
+struct bcm6345_reset_priv {
+ struct regmap *map;
+ u32 offset;
+ struct reset_controller_dev rcdev;
+ struct mutex mutex;
+};
+
+static int bcm6345_reset_reset(struct reset_controller_dev *rcdev,
+ unsigned long id)
+{
+ struct bcm6345_reset_priv *priv = to_bcm6345_reset_priv(rcdev);
+
+ mutex_lock(&priv->mutex);
+ regmap_write_bits(priv->map, priv->offset, BIT(id), 0);
+ usleep_range(10000, 20000);
+ regmap_write_bits(priv->map, priv->offset, BIT(id), BIT(id));
+ usleep_range(10000, 20000);
+ mutex_unlock(&priv->mutex);
+
+ return 0;
+}
+
+static struct reset_control_ops bcm6345_reset_ops = {
+ .reset = bcm6345_reset_reset,
+};
+
+static int __init bcm6345_reset_probe(struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct bcm6345_reset_priv *priv;
+ int ret;
+
+ priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ mutex_init(&priv->mutex);
+
+ priv->map = syscon_regmap_lookup_by_phandle(np, "regmap");
+ if (IS_ERR(priv->map))
+ return PTR_ERR(priv->map);
+
+ if (of_property_read_u32(np, "offset", &priv->offset))
+ return -EINVAL;
+
+ priv->rcdev.owner = THIS_MODULE;
+ priv->rcdev.ops = &bcm6345_reset_ops;
+ priv->rcdev.nr_resets = 32;
+ priv->rcdev.of_node = pdev->dev.of_node;
+
+ ret = reset_controller_register(&priv->rcdev);
+ if (ret) {
+ dev_err(&pdev->dev,
+ "unable to register reset controller: %d\n", ret);
+ return ret;
+ }
+
+ dev_info(&pdev->dev, "registered reset controller\n");
+ return 0;
+}
+
+static const struct of_device_id bcm6345_reset_dt_match[] __initconst = {
+ { .compatible = "brcm,bcm6345-reset" },
+ { },
+};
+MODULE_DEVICE_TABLE(of, bcm6345_reset_dt_match);
+
+static struct platform_driver bcm6345_reset_driver __refdata = {
+ .probe = bcm6345_reset_probe,
+ .driver = {
+ .name = "bcm6345-reset",
+ .of_match_table = bcm6345_reset_dt_match,
+ },
+};
+module_platform_driver(bcm6345_reset_driver);
+
+MODULE_DESCRIPTION("BCM6345 reset driver");
+MODULE_AUTHOR("Simon Arlott");
+MODULE_LICENSE("GPL");
--
2.1.4
--
Simon Arlott
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 4+ messages in thread* Re: [PATCH linux-next (v3) 1/2] reset: Add brcm,bcm6345-reset device tree binding
[not found] ` <5669EE86.8030406-qdVf85lJwsCyrPCCpiK2c/XRex20P6io@public.gmane.org>
2015-12-10 21:34 ` [PATCH linux-next (v3) 2/2] reset: bcm6345: Add support for the BCM6345 soft-reset controller Simon Arlott
@ 2015-12-11 3:47 ` Rob Herring
1 sibling, 0 replies; 4+ messages in thread
From: Rob Herring @ 2015-12-11 3:47 UTC (permalink / raw)
To: Simon Arlott
Cc: Philipp Zabel, Kevin Cernekee, Florian Fainelli,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, MIPS Mailing List,
Pawel Moll, Mark Rutland, Ian Campbell, Sergei Shtylyov,
Jonas Gorski
On Thu, Dec 10, 2015 at 09:28:38PM +0000, Simon Arlott wrote:
> Add device tree binding for the BCM6345 soft reset controller.
>
> The BCM6345 contains a soft-reset controller activated by setting
> a bit (that must previously have been cleared).
>
> Signed-off-by: Simon Arlott <simon-A6De1vDTPLDsq35pWSNszA@public.gmane.org>
> ---
> v3: Resend. Example has changed because usbh now has two compatible
> strings and uses a power domain instead of a regulator.
Not really all that important to this binding definition, so you can
keep my ack.
>
> v2: Renamed to bcm6345, removed "mask" property.
> Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
>
> .../bindings/reset/brcm,bcm6345-reset.txt | 33 ++++++++++++++++++++++
> 1 file changed, 33 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/reset/brcm,bcm6345-reset.txt
>
> diff --git a/Documentation/devicetree/bindings/reset/brcm,bcm6345-reset.txt b/Documentation/devicetree/bindings/reset/brcm,bcm6345-reset.txt
> new file mode 100644
> index 0000000..0313040
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/reset/brcm,bcm6345-reset.txt
> @@ -0,0 +1,33 @@
> +Broadcom BCM6345 reset controller
> +
> +The BCM6345 contains a basic soft reset controller in the perf register
> +set which resets components using a bit in a register.
> +
> +Please also refer to reset.txt in this directory for common reset
> +controller binding usage.
> +
> +Required properties:
> +- compatible: Should be "brcm,bcm<soc>-reset", "brcm,bcm6345-reset"
> +- regmap: The register map phandle
> +- offset: Offset in the register map for the reset register (in bytes)
> +- #reset-cells: Must be set to 1
> +
> +Example:
> +
> +periph_soft_rst: reset-controller {
> + compatible = "brcm,bcm63168-reset", "brcm,bcm6345-reset";
> + regmap = <&periph_cntl>;
> + offset = <0x10>;
> +
> + #reset-cells = <1>;
> +};
> +
> +usbh: usbphy@10002700 {
> + compatible = "brcm,bcm63168-usbh", "brcm,bcm6328-usbh";
> + reg = <0x10002700 0x38>;
> + clocks = <&periph_clk 13>, <&timer_clk 18>;
> + resets = <&periph_soft_rst 6>;
> + power-domains = <&misc_iddq_ctrl 4>;
> + #phy-cells = <0>;
> +};
> +
> --
> 2.1.4
>
> --
> Simon Arlott
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 4+ messages in thread