Re: [PATCH 5/6] arm64: dts: rockchip: Enable USB for Khadas Edge 2L

[Heiko Stuebner <heiko@sntech.de>]

Am Mittwoch, 25. März 2026, 06:46:13 Mitteleuropäische Sommerzeit schrieb Gray Huang:
> The Khadas Edge 2L board provides one USB 3.0 Host port and one
> USB 2.0 port (connected via an internal hub). Enable the
> corresponding DWC3 controllers and PHYs.
> 
> Signed-off-by: Gray Huang <gray.huang@wesion.com>
> ---
>  .../dts/rockchip/rk3576-khadas-edge-2l.dts    | 47 +++++++++++++++++++
>  1 file changed, 47 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/rockchip/rk3576-khadas-edge-2l.dts b/arch/arm64/boot/dts/rockchip/rk3576-khadas-edge-2l.dts
> index 003342fd69a7..8ecd00f6645d 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3576-khadas-edge-2l.dts
> +++ b/arch/arm64/boot/dts/rockchip/rk3576-khadas-edge-2l.dts
> @@ -30,6 +30,29 @@ hdmi_con_in: endpoint {
>  		};
>  	};
>  
> +	vcc5v0_device: regulator-vcc5v0-device {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc5v0_device";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +	};
> +
> +	vcc5v0_host: regulator-vcc5v0-host {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc5v0_host";
> +		regulator-boot-on;
> +		regulator-always-on;
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		enable-active-high;
> +		gpio = <&gpio2 RK_PD3 GPIO_ACTIVE_HIGH>;
> +		vin-supply = <&vcc5v0_device>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&usb_host_pwren>;
> +	};
> +
>  	vcc_sys: regulator-vcc5v0-sys {
>  		compatible = "regulator-fixed";
>  		regulator-name = "vcc_sys";
> @@ -531,6 +554,12 @@ pcie0_rst: pcie0-rst {
>  		};
>  	};
>  
> +	usb {
> +		usb_host_pwren: usb-host-pwren {
> +			rockchip,pins = <2 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +	};
> +
>  	wifi {
>  		wifi_reg_on: wifi-reg-on {
>  			rockchip,pins = <4 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
> @@ -542,6 +571,24 @@ wifi_wake_host: wifi-wake-host {
>  	};
>  };
>  
> +&usb_drd1_dwc3 {
> +	dr_mode = "host";
> +	status = "okay";
> +};
> +
> +&u2phy1 {
> +	status = "okay";
> +};
> +
> +&u2phy1_otg {
> +	phy-supply = <&vcc5v0_host>;
> +	status = "okay";
> +};
> +
> +&combphy1_psu {
> +	status = "okay";
> +};

same here, u-something and c-something between pinctrl and sdhci
is the wrong place.

Heko

> +
>  &sdhci {
>  	bus-width = <8>;
>  	no-sdio;
>