From: Chanwoo Choi <cw00.choi@samsung.com>
To: Krzysztof Kozlowski <k.kozlowski@samsung.com>,
kgene@kernel.org, s.nawrocki@samsung.com, tomasz.figa@gmail.com
Cc: jh80.chung@samsung.com, andi.shyti@samsung.com,
inki.dae@samsung.com, sw0312.kim@samsung.com,
pankaj.dubey@samsung.com, linux-samsung-soc@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, devicetree@vger.kernel.org
Subject: Re: [PATCH 07/10] ARM: dts: Add thermal zone and cpufreq node for exynos3250-artik5 module
Date: Mon, 14 Mar 2016 16:13:22 +0900 [thread overview]
Message-ID: <56E66492.4070003@samsung.com> (raw)
In-Reply-To: <56E662F6.4070200@samsung.com>
On 2016년 03월 14일 16:06, Krzysztof Kozlowski wrote:
> On 14.03.2016 11:04, Chanwoo Choi wrote:
>> This patch enables the CPU frequency scaling for exynos3250-artik5 module
>> and adds the thernal zones with cpu cooling device to prevent the overheat
>> temperature.
>>
>> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
>> ---
>> arch/arm/boot/dts/exynos3250-artik5.dtsi | 23 +++++++++++++++++++++++
>> 1 file changed, 23 insertions(+)
>
> The patch looks good but just squash it with 5/10 unless there is some
> benefit by splitting the features for many patches. The benefit would be
> for example submitting the work partially, in steps, following principle
> release-early-release-often... but this is not the case. You have
> everything ready and tested.
OK. I'll merge this patch with 5/10 patch.
Best Regards,
Chanwoo Choi
>
> BR,
> Krzysztof
>
>>
>> diff --git a/arch/arm/boot/dts/exynos3250-artik5.dtsi b/arch/arm/boot/dts/exynos3250-artik5.dtsi
>> index 75b291c10cdc..877e4827df83 100644
>> --- a/arch/arm/boot/dts/exynos3250-artik5.dtsi
>> +++ b/arch/arm/boot/dts/exynos3250-artik5.dtsi
>> @@ -31,6 +31,25 @@
>> compatible = "samsung,secure-firmware";
>> reg = <0x0205F000 0x1000>;
>> };
>> +
>> + thermal-zones {
>> + cpu_thermal: cpu-thermal {
>> + cooling-maps {
>> + map0 {
>> + /* Corresponds to 500MHz */
>> + cooling-device = <&cpu0 5 5>;
>> + };
>> + map1 {
>> + /* Corresponds to 200MHz */
>> + cooling-device = <&cpu0 8 8>;
>> + };
>> + };
>> + };
>> + };
>> +};
>> +
>> +&cpu0 {
>> + cpu0-supply = <&buck2_reg>;
>> };
>>
>> &i2c_0 {
>> @@ -296,6 +315,10 @@
>> status = "okay";
>> };
>>
>> +&tmu {
>> + status = "okay";
>> +};
>> +
>> &xusbxti {
>> clock-frequency = <24000000>;
>> };
>>
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
>
next prev parent reply other threads:[~2016-03-14 7:13 UTC|newest]
Thread overview: 36+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-03-14 2:04 [PATCH 00/10] ARM: dts: Add new Exynos3250-based ARTIK5 module dtsi file Chanwoo Choi
2016-03-14 2:04 ` [PATCH 01/10] clk: samsung: exynos3250: Add UART2 clock Chanwoo Choi
2016-03-14 2:04 ` [PATCH 03/10] ARM: dts: Add UART2 dt node for Exynos3250 SoC Chanwoo Choi
2016-03-14 2:04 ` [PATCH 04/10] ARM: dts: Add MSHC2 " Chanwoo Choi
2016-03-14 6:22 ` Krzysztof Kozlowski
2016-03-14 8:28 ` Chanwoo Choi
2016-03-14 9:52 ` Krzysztof Kozlowski
2016-03-14 2:04 ` [PATCH 05/10] ARM: dts: Add exynos3250-artik5 dtsi file for ARTIK5 module Chanwoo Choi
2016-03-14 6:42 ` Krzysztof Kozlowski
2016-03-14 6:57 ` Chanwoo Choi
2016-03-14 7:22 ` Chanwoo Choi
2016-03-14 2:04 ` [PATCH 06/10] ARM: dts: Add MSHC0 dt node for eMMC device for exynos3250-artik5 module Chanwoo Choi
[not found] ` <1457921056-21257-7-git-send-email-cw00.choi-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
2016-03-14 6:57 ` Krzysztof Kozlowski
2016-03-14 8:15 ` Chanwoo Choi
2016-03-14 9:59 ` Krzysztof Kozlowski
2016-03-14 2:04 ` [PATCH 06/10] ARM: dts: exynos3250-artik5: Add MSHC0 dt node for eMMC device Chanwoo Choi
2016-03-14 2:10 ` Chanwoo Choi
2016-03-14 2:04 ` [PATCH 07/10] ARM: dts: Add thermal zone and cpufreq node for exynos3250-artik5 module Chanwoo Choi
2016-03-14 7:06 ` Krzysztof Kozlowski
2016-03-14 7:13 ` Chanwoo Choi [this message]
[not found] ` <1457921056-21257-1-git-send-email-cw00.choi-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
2016-03-14 2:04 ` [PATCH 02/10] clk: samsung: exynos3250: Add MMC2 clock Chanwoo Choi
2016-03-14 2:04 ` [PATCH 08/10] ARM: dts: Add rtc and adc dt node for exynos3250-artik5 module Chanwoo Choi
2016-03-14 7:12 ` Krzysztof Kozlowski
[not found] ` <56E66462.9000402-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
2016-03-14 7:21 ` Chanwoo Choi
2016-03-14 2:04 ` [PATCH 09/10] ARM: dts: Add MSHC2 dt node for SD card for exynos3250-artik5-devel board Chanwoo Choi
2016-03-14 8:31 ` Krzysztof Kozlowski
2016-03-14 8:48 ` Chanwoo Choi
2016-03-14 9:44 ` Krzysztof Kozlowski
2016-03-14 10:22 ` Chanwoo Choi
2016-03-15 0:25 ` Krzysztof Kozlowski
2016-03-15 0:56 ` Jaehoon Chung
[not found] ` <56E75DC1.7000807-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
2016-03-15 1:45 ` Chanwoo Choi
2016-03-15 1:46 ` Chanwoo Choi
2016-03-14 2:04 ` [PATCH 10/10] ARM: dts: Add PPMU node for exynos3250-artik5 module Chanwoo Choi
2016-03-14 8:34 ` Krzysztof Kozlowski
2016-03-14 8:43 ` Chanwoo Choi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=56E66492.4070003@samsung.com \
--to=cw00.choi@samsung.com \
--cc=andi.shyti@samsung.com \
--cc=devicetree@vger.kernel.org \
--cc=inki.dae@samsung.com \
--cc=jh80.chung@samsung.com \
--cc=k.kozlowski@samsung.com \
--cc=kgene@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-samsung-soc@vger.kernel.org \
--cc=pankaj.dubey@samsung.com \
--cc=s.nawrocki@samsung.com \
--cc=sw0312.kim@samsung.com \
--cc=tomasz.figa@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).