Re: [PATCH v2 2/2] riscv: dts: starfive: add DT for Orange Pi RV

[Icenowy Zheng <uwu@icenowy.me>]

在 2025-09-30星期二的 18:03 +0800，Icenowy Zheng写道：
> Orange Pi RV is a newly released SBC with JH7110 SoC, single GbE port
> (connected to JH7110 GMAC0 via a YT8531 PHY), 4 USB ports (via a
> VL805
> PCIe USB controller connected to JH7110 PCIE0), a M.2 M-key slot
> (connected to JH7110 PCIE1), a HDMI video output, a 3.5mm audio
> output
> and a microSD slot.
> 
> Other Onboard peripherals contain a SPI NOR (which contains the U-
> Boot
> firmware), a 24c02 EEPROM storing some StarFive-specific information
> (factory programmed and read only by default) and an Ampak AP6256
> SDIO
> Wi-Fi module.
> 
> Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
> ---
> Changes in v2:
> - Property order change mentioned in the review of v1.
> - Added Wi-Fi (along with the always on VCC3V3_PCIE regulator, which
> is
>   used to power up WIFI_3V3). The OOB IRQ is still not possible to
> use
>   because of some incompatibility between StarFive pinctrl driver and
>   brcmfmac.
> - Removed the LED because it's in common DTSI.
> 
>  arch/riscv/boot/dts/starfive/Makefile         |  1 +
>  .../boot/dts/starfive/jh7110-orangepi-rv.dts  | 87
> +++++++++++++++++++
>  2 files changed, 88 insertions(+)
>  create mode 100644 arch/riscv/boot/dts/starfive/jh7110-orangepi-
> rv.dts
> 
> diff --git a/arch/riscv/boot/dts/starfive/Makefile
> b/arch/riscv/boot/dts/starfive/Makefile
> index b3bb12f78e7d5..24f1a44828350 100644
> --- a/arch/riscv/boot/dts/starfive/Makefile
> +++ b/arch/riscv/boot/dts/starfive/Makefile
> @@ -10,6 +10,7 @@ dtb-$(CONFIG_ARCH_STARFIVE) += jh7100-starfive-
> visionfive-v1.dtb
>  
>  dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-deepcomputing-fml13v01.dtb
>  dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-milkv-mars.dtb
> +dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-orangepi-rv.dtb
>  dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-pine64-star64.dtb
>  dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-starfive-visionfive-2-
> v1.2a.dtb
>  dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-starfive-visionfive-2-
> v1.3b.dtb
> diff --git a/arch/riscv/boot/dts/starfive/jh7110-orangepi-rv.dts
> b/arch/riscv/boot/dts/starfive/jh7110-orangepi-rv.dts
> new file mode 100644
> index 0000000000000..5a917b7db6f78
> --- /dev/null
> +++ b/arch/riscv/boot/dts/starfive/jh7110-orangepi-rv.dts
> @@ -0,0 +1,87 @@
> +// SPDX-License-Identifier: GPL-2.0 OR MIT
> +/*
> + * Copyright (C) 2025 Icenowy Zheng <uwu@icenowy.me>
> + */
> +
> +/dts-v1/;
> +#include "jh7110-common.dtsi"
> +
> +/ {
> +       model = "Xunlong Orange Pi RV";
> +       compatible = "xunlong,orangepi-rv", "starfive,jh7110";
> +
> +       /* This regulator is always on by hardware */
> +       reg_vcc3v3_pcie: regulator-vcc3v3-pcie {
> +               compatible = "regulator-fixed";
> +               regulator-name = "vcc3v3-pcie";
> +               regulator-min-microvolt = <3300000>;
> +               regulator-max-microvolt = <3300000>;
> +               regulator-always-on;
> +       };
> +
> +       wifi_pwrseq: wifi-pwrseq {
> +               compatible = "mmc-pwrseq-simple";
> +               reset-gpios = <&sysgpio 62 GPIO_ACTIVE_LOW>;
> +       };
> +};
> +
> +&gmac0 {
> +       assigned-clocks = <&aoncrg JH7110_AONCLK_GMAC0_TX>;
> +       assigned-clock-parents = <&aoncrg
> JH7110_AONCLK_GMAC0_RMII_RTX>;
> +       starfive,tx-use-rgmii-clk;
> +       status = "okay";
> +};
> +
> +&mmc0 {
> +       #address-cells = <1>;
> +       #size-cells = <0>;
> +       cap-sd-highspeed;
> +       mmc-pwrseq = <&wifi_pwrseq>;
> +       vmmc-supply = <&reg_vcc3v3_pcie>;
> +       vqmmc-supply = <&vcc_3v3>;
> +       status = "okay";
> +
> +       ap6256: wifi@1 {
> +               compatible = "brcm,bcm43456-fmac", "brcm,bcm4329-
> fmac";
> +               reg = <1>;
> +               /* TODO: out-of-band IRQ on GPIO21 */
> +       };
> +};
> +
> +&mmc0_pins {
> +       /*
> +        * As the MMC0 bus is used to connect a SDIO Wi-Fi card
> instead of
> +        * an eMMC card, and the eMMC RST is repurposed to be an
> enablement
> +        * pin of the SDIO Wi-Fi, remove it from the pinctrl node and
> manage
> +        * it as a GPIO instead.
> +        */
> +       /delete-node/ rst-pins;
> +};
> +
> +&mmc1 {
> +       /delete-property/ cd-gpios;
> +       broken-cd;

Well it's found that the card detect is working, although with
different polarity with other boards.

Here should be:
```
	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_HIGH>;
```

Will be fixed in the next revision.

> +};
> +
> +&pcie0 {
> +       status = "okay";
> +};
> +
> +&pcie1 {
> +       status = "okay";
> +};
> +
> +&phy0 {
> +       rx-internal-delay-ps = <1500>;
> +       tx-internal-delay-ps = <1500>;
> +       motorcomm,tx-clk-adj-enabled;
> +       motorcomm,tx-clk-10-inverted;
> +       motorcomm,tx-clk-100-inverted;
> +       motorcomm,tx-clk-1000-inverted;
> +       motorcomm,rx-clk-drv-microamp = <3970>;
> +       motorcomm,rx-data-drv-microamp = <2910>;
> +};
> +
> +&pwmdac {
> +       status = "okay";
> +};