* [PATCH v3 1/2] ARM: dts: aspeed: Add device tree for Nvidia's GB200NVL BMC
2025-03-20 16:46 [PATCH v3 0/2] Add device tree for Nvidia's GB200NVL BMC Willie Thai
@ 2025-03-20 16:46 ` Willie Thai
2025-03-20 16:54 ` Andrew Lunn
2025-03-21 7:44 ` Krzysztof Kozlowski
2025-03-20 16:46 ` [PATCH v3 2/2] dt-bindings: arm: aspeed: add " Willie Thai
2025-03-20 18:26 ` [PATCH v3 0/2] Add device tree for " Rob Herring (Arm)
2 siblings, 2 replies; 10+ messages in thread
From: Willie Thai @ 2025-03-20 16:46 UTC (permalink / raw)
To: robh, krzk+dt, conor+dt, joel, andrew, kees, tony.luck, gpiccoli,
devicetree, linux-arm-kernel, linux-aspeed, linux-kernel,
linux-hardening, openbmc
Cc: wthai, leohu, tingkaic, dkodihalli, Mars Yang,
Krzysztof Kozlowski, Andrew Lunn, Paul Menzel
The GB200NVL BMC is an Aspeed Ast2600 based BMC
for Nvidia Blackwell GB200NVL platform.
Reference to Ast2600 SOC [1].
Reference to Blackwell GB200NVL Platform [2].
Co-developed-by: Mars Yang <maryang@nvidia.com>
Signed-off-by: Mars Yang <maryang@nvidia.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Rob Herring <robh@kernel.org>
Cc: Paul Menzel <pmenzel@molgen.mpg.de>
Link: https://www.aspeedtech.com/server_ast2600/ [1]
Link: https://nvdam.widen.net/s/wwnsxrhm2w/blackwell-datasheet-3384703 [2]
Signed-off-by: Willie Thai <wthai@nvidia.com>
---
Changes v1 -> v2:
- Fix the SOB name [Krzysztof]
- Fix warnings from scripts/checkpatch.pl run [Krzysztof]
- Fix DTS coding style [Krzysztof]
- Move pinctrl override to the bottom [Krzysztof]
- Drop bootargs [Krzysztof]
- Follow DTS coding style and change naming for leds node [Krzysztof]
- Change flash 0 status property [Krzysztof]
- Change the phy-mode to rgmii [Andrew]
- Remove the max-speed in mac0 [Andrew]
- Put gpio line name in one line per group of 8 gpios, but keep some b/c they can exceed length limit [Paul]
Changes v2 -> v3:
- Fix missing new line [Krzysztof]
- Fix missing binding define, adding it in the patch no.1 of this patch set v3 [Krzysztof, Rob]
- Fix DTS coding style [Krzysztof]
- Modify nodes name to generic name for: i2c expander pca9546, gpio expander pca9555, power monitor lm5066i, fan controller max31790 [Krzysztof]
- Skip mac setting and wait till the delay issue in phy-mode fix from Aspeed SOC vendor side [Andrew]
- Remove i2c-scl-clk-low-timeout-us which is Apseed proprietary property [Mars]
---
---
arch/arm/boot/dts/aspeed/Makefile | 1 +
.../aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dts | 1168 +++++++++++++++++
2 files changed, 1169 insertions(+)
create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dts
diff --git a/arch/arm/boot/dts/aspeed/Makefile b/arch/arm/boot/dts/aspeed/Makefile
index 2e5f4833a073..20fd357a1ee9 100644
--- a/arch/arm/boot/dts/aspeed/Makefile
+++ b/arch/arm/boot/dts/aspeed/Makefile
@@ -50,6 +50,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
aspeed-bmc-lenovo-hr630.dtb \
aspeed-bmc-lenovo-hr855xg2.dtb \
aspeed-bmc-microsoft-olympus.dtb \
+ aspeed-bmc-nvidia-gb200nvl-bmc.dtb \
aspeed-bmc-opp-lanyang.dtb \
aspeed-bmc-opp-mowgli.dtb \
aspeed-bmc-opp-nicole.dtb \
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dts
new file mode 100644
index 000000000000..0370a7b25181
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dts
@@ -0,0 +1,1168 @@
+// SPDX-License-Identifier: GPL-2.0+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "AST2600 GB200NVL BMC";
+ compatible = "nvidia,gb200nvl-bmc", "aspeed,ast2600";
+
+ aliases {
+ serial2 = &uart3;
+ serial4 = &uart5;
+ i2c16 = &imux16;
+ i2c17 = &imux17;
+ i2c18 = &imux18;
+ i2c19 = &imux19;
+ i2c20 = &imux20;
+ i2c21 = &imux21;
+ i2c22 = &imux22;
+ i2c23 = &imux23;
+ i2c24 = &imux24;
+ i2c25 = &imux25;
+ i2c26 = &imux26;
+ i2c27 = &imux27;
+ i2c28 = &imux28;
+ i2c29 = &imux29;
+ i2c30 = &imux30;
+ i2c31 = &imux31;
+ i2c32 = &imux32;
+ i2c33 = &imux33;
+ i2c34 = &imux34;
+ i2c35 = &imux35;
+ i2c36 = &imux36;
+ i2c37 = &imux37;
+ i2c38 = &imux38;
+ i2c39 = &imux39;
+ i2c40 = &e1si2c0;
+ i2c41 = &e1si2c1;
+ i2c42 = &e1si2c2;
+ i2c43 = &e1si2c3;
+ i2c44 = &e1si2c4;
+ i2c45 = &e1si2c5;
+ i2c46 = &e1si2c6;
+ i2c47 = &e1si2c7;
+ i2c48 = &i2c17mux0;
+ i2c49 = &i2c17mux1;
+ i2c50 = &i2c17mux2;
+ i2c51 = &i2c17mux3;
+ i2c52 = &i2c25mux0;
+ i2c53 = &i2c25mux1;
+ i2c54 = &i2c25mux2;
+ i2c55 = &i2c25mux3;
+ i2c56 = &i2c29mux0;
+ i2c57 = &i2c29mux1;
+ i2c58 = &i2c29mux2;
+ i2c59 = &i2c29mux3;
+ };
+
+ chosen {
+ stdout-path = &uart5;
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x80000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ vga_memory: framebuffer@9f000000 {
+ no-map;
+ reg = <0x9f000000 0x01000000>; /* 16M */
+ };
+
+ ramoops@a0000000 {
+ compatible = "ramoops";
+ reg = <0xa0000000 0x100000>; /* 1MB */
+ record-size = <0x10000>; /* 64KB */
+ max-reason = <2>; /* KMSG_DUMP_OOPS */
+ };
+
+ gfx_memory: framebuffer {
+ size = <0x01000000>;
+ alignment = <0x01000000>;
+ compatible = "shared-dma-pool";
+ reusable;
+ };
+
+ video_engine_memory: jpegbuffer {
+ size = <0x02000000>; /* 32M */
+ alignment = <0x01000000>;
+ compatible = "shared-dma-pool";
+ reusable;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ led-0 {
+ label = "uid_led";
+ gpios = <&sgpiom0 27 GPIO_ACTIVE_LOW>;
+ };
+ led-1 {
+ label = "fault_led";
+ gpios = <&sgpiom0 29 GPIO_ACTIVE_LOW>;
+ };
+ led-2 {
+ label = "power_led";
+ gpios = <&sgpiom0 31 GPIO_ACTIVE_LOW>;
+ };
+
+ };
+
+ buttons {
+ button-power {
+ label = "power-btn";
+ gpio = <&sgpiom0 156 GPIO_ACTIVE_LOW>;
+ };
+ button-uid {
+ label = "uid-btn";
+ gpio = <&sgpiom0 154 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+};
+
+// Enable Primary flash on FMC for bring up activity
+&fmc {
+ status = "okay";
+ flash@0 {
+ status = "okay";
+ compatible = "jedec,spi-nor";
+ label = "bmc";
+ spi-max-frequency = <50000000>;
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ u-boot@0 {
+ // 896KB
+ reg = <0x0 0xe0000>;
+ label = "u-boot";
+ };
+
+ kernel@100000 {
+ // 9MB
+ reg = <0x100000 0x900000>;
+ label = "kernel";
+ };
+
+ rofs@a00000 {
+ // 55292KB (extends to end of 64MB SPI - 4KB)
+ reg = <0xa00000 0x35FF000>;
+ label = "rofs";
+ };
+ };
+ };
+};
+
+&spi2 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi2_default>;
+
+ // Data SPI is 64MB in size
+ flash@0 {
+ status = "okay";
+ label = "config";
+ spi-max-frequency = <50000000>;
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ u-boot-env@0 {
+ // 256KB
+ reg = <0x0 0x40000>;
+ label = "u-boot-env";
+ };
+
+ rwfs@40000 {
+ // 16MB
+ reg = <0x40000 0x1000000>;
+ label = "rwfs";
+ };
+
+ log@1040000 {
+ // 40MB
+ reg = <0x1040000 0x2800000>;
+ label = "log";
+ };
+ };
+ };
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart3 {
+ // Enabling SOL
+ status = "okay";
+};
+
+&uart5 {
+ // BMC Debug Console
+ status = "okay";
+};
+
+&uart_routing {
+ status = "okay";
+};
+
+&mac2 {
+ status = "okay";
+ phy-mode = "rmii";
+ use-ncsi;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rmii3_default>;
+};
+
+// Enable emmc
+&emmc_controller {
+ status = "okay";
+};
+
+&emmc {
+ non-removable;
+ pinctrl-0 = <&pinctrl_emmcg5_default>;
+ bus-width = <4>;
+ max-frequency = <52000000>;
+ clk-phase-mmc-hs200 = <9>, <225>;
+};
+
+/*
+ * Enable USB port A as device (via the virtual hub) to host
+ */
+&vhub {
+ status = "okay";
+ pinctrl-names = "default";
+ /*
+ * Uncomment below line to enable internal EHCI controller
+ * Current config uses xHCI Port1
+ */
+};
+
+&video {
+ status = "okay";
+ memory-region = <&video_engine_memory>;
+};
+
+// USB 2.0 to HMC, on USB Port B
+&ehci1 {
+ status = "okay";
+};
+
+// USB 1.0
+&uhci {
+ status = "okay";
+};
+
+&sgpiom0 {
+ status="okay";
+ ngpios = <128>;
+ gpio-line-names =
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "RUN_POWER_FAULT_L-I","SYS_RST_IN_L-O",
+ "RUN_POWER_PG-I","PWR_BRAKE_L-O",
+ "SYS_RST_OUT_L-I","RUN_POWER_EN-O",
+ "L0L1_RST_REQ_OUT_L-I","SHDN_FORCE_L-O",
+ "L2_RST_REQ_OUT_L-I","SHDN_REQ_L-O",
+ "SHDN_OK_L-I","UID_LED_N-O",
+ "BMC_I2C1_FPGA_ALERT_L-I","SYS_FAULT_LED_N-O",
+ "BMC_I2C0_FPGA_ALERT_L-I","PWR_LED_N-O",
+ "FPGA_RSVD_FFU3-I","",
+ "FPGA_RSVD_FFU2-I","",
+ "FPGA_RSVD_FFU1-I","",
+ "FPGA_RSVD_FFU0-I","BMC_I2C_SSIF_ALERT_L-O",
+ "CPU_BOOT_DONE-I","JTAG_MUX_SELECT-O",
+ "SPI_BMC_FPGA_INT_L-I","RTC_CLR_L-O",
+ "THERM_BB_WARN_L-I","UART_MUX_SEL-O",
+ "THERM_BB_OVERT_L-I","",
+ "CPU0_UPHY3_PRSNT1_L-I","IOBRD0_RUN_POWER_EN-O",
+ "CPU0_UPHY3_PRSNT0_L-I","IOBRD1_RUN_POWER_EN-O",
+ "CPU0_UPHY2_PRSNT1_L-I","FPGA_RSVD_FFU4-O",
+ "CPU0_UPHY2_PRSNT0_L-I","FPGA_RSVD_FFU5-O",
+ "CPU0_UPHY1_PRSNT1_L-I","FPGA_RSVD_FFU6-O",
+ "CPU0_UPHY1_PRSNT0_L-I","FPGA_RSVD_FFU7-O",
+ "CPU0_UPHY0_PRSNT1_L-I","RSVD_NV_PLT_DETECT-O",
+ "CPU0_UPHY0_PRSNT0_L-I","SPI1_INT_L-O",
+ "CPU1_UPHY3_PRSNT1_L-I","",
+ "CPU1_UPHY3_PRSNT0_L-I","HMC_EROT_MUX_STATUS",
+ "CPU1_UPHY2_PRSNT1_L-I","",
+ "CPU1_UPHY2_PRSNT0_L-I","",
+ "CPU1_UPHY1_PRSNT1_L-I","",
+ "CPU1_UPHY1_PRSNT0_L-I","",
+ "CPU1_UPHY0_PRSNT1_L-I","",
+ "CPU1_UPHY0_PRSNT0_L-I","",
+ "FAN1_PRESENT_L-I","",
+ "FAN0_PRESENT_L-I","",
+ "","",
+ "IPEX_CABLE_PRSNT_L-I","",
+ "M2_1_PRSNT_L-I","",
+ "M2_0_PRSNT_L-I","",
+ "CPU1_UPHY4_PRSNT1_L-I","",
+ "CPU0_UPHY4_PRSNT0_L-I","",
+ "","",
+ "I2C_RTC_ALERT_L-I","",
+ "FAN7_PRESENT_L-I","",
+ "FAN6_PRESENT_L-I","",
+ "FAN5_PRESENT_L-I","",
+ "FAN4_PRESENT_L-I","",
+ "FAN3_PRESENT_L-I","",
+ "FAN2_PRESENT_L-I","",
+ "IOBRD0_IOX_INT_L-I","",
+ "IOBRD1_PRSNT_L-I","",
+ "IOBRD0_PRSNT_L-I","",
+ "IOBRD1_PWR_GOOD-I","",
+ "IOBRD0_PWR_GOOD-I","",
+ "","",
+ "","",
+ "FAN_FAIL_IN_L-I","",
+ "","",
+ "","",
+ "","",
+ "PDB_CABLE_PRESENT_L-I","",
+ "","",
+ "CHASSIS_PWR_BRK_L-I","",
+ "","",
+ "IOBRD1_IOX_INT_L-I","",
+ "10GBE_SMBALRT_L-I","",
+ "PCIE_WAKE_L-I","",
+ "I2C_M21_ALERT_L-I","",
+ "I2C_M20_ALERT_L-I","",
+ "TRAY_FAST_SHDN_L-I","",
+ "UID_BTN_N-I","",
+ "PWR_BTN_L-I","",
+ "PSU_SMB_ALERT_L-I","",
+ "","",
+ "","",
+ "NODE_LOC_ID[0]-I","",
+ "NODE_LOC_ID[1]-I","",
+ "NODE_LOC_ID[2]-I","",
+ "NODE_LOC_ID[3]-I","",
+ "NODE_LOC_ID[4]-I","",
+ "NODE_LOC_ID[5]-I","",
+ "FAN10_PRESENT_L-I","",
+ "FAN9_PRESENT_L-I","",
+ "FAN8_PRESENT_L-I","",
+ "FPGA1_READY_HMC-I","",
+ "DP_HPD-I","",
+ "HMC_I2C3_FPGA_ALERT_L-I","",
+ "HMC_I2C2_FPGA_ALERT_L-I","",
+ "FPGA0_READY_HMC-I","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "LEAK_DETECT_ALERT_L-I","",
+ "MOD1_B2B_CABLE_PRESENT_L-I","",
+ "MOD1_CLINK_CABLE_PRESENT_L-I","",
+ "FAN11_PRESENT_L-I","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "","",
+ "RSVD_SGPIO_IN_CRC[0]","RSVD_SGPIO_O_CRC[7]",
+ "RSVD_SGPIO_IN_CRC[1]","RSVD_SGPIO_O_CRC[6]",
+ "RSVD_SGPIO_IN_CRC[2]","RSVD_SGPIO_O_CRC[5]",
+ "RSVD_SGPIO_IN_CRC[3]","RSVD_SGPIO_O_CRC[4]",
+ "RSVD_SGPIO_IN_CRC[4]","RSVD_SGPIO_O_CRC[3]",
+ "RSVD_SGPIO_IN_CRC[5]","RSVD_SGPIO_O_CRC[2]",
+ "RSVD_SGPIO_IN_CRC[6]","RSVD_SGPIO_O_CRC[1]",
+ "RSVD_SGPIO_IN_CRC[7]","RSVD_SGPIO_O_CRC[0]";
+};
+
+// I2C1, SSIF IPMI interface
+&i2c0 {
+ status = "okay";
+ clock-frequency = <400000>;
+ disable-master = <1>;
+ ssif-bmc@10 {
+ compatible = "ssif-bmc";
+ reg = <0x10>;
+ };
+};
+
+// I2C2
+// BMC_I2C1_FPGA - Secondary FPGA
+// HMC EROT
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+ multi-master;
+};
+
+// I2C3
+// BMC_I2C0_FPGA - Primary FPGA
+// HMC FRU EEPROM
+&i2c2 {
+ status = "okay";
+ clock-frequency = <400000>;
+ multi-master;
+};
+
+// I2C4
+&i2c3 {
+ status = "disabled";
+};
+
+// I2C5
+// RTC Driver
+// IO Expander
+&i2c4 {
+ status = "okay";
+ clock-frequency = <400000>;
+ // Module 0, Expander @0x21
+ exp4: gpio@21 {
+ compatible = "nxp,pca9555";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
+
+ gpio-line-names =
+ "RTC_MUX_SEL-O",
+ "PCI_MUX_SEL-O",
+ "TPM_MUX_SEL-O",
+ "FAN_MUX-SEL-O",
+ "SGMII_MUX_SEL-O",
+ "DP_MUX_SEL-O",
+ "UPHY3_USB_SEL-O",
+ "NCSI_MUX_SEL-O",
+ "BMC_PHY_RST-O",
+ "RTC_CLR_L-O",
+ "BMC_12V_CTRL-O",
+ "PS_RUN_IO0_PG-I",
+ "",
+ "",
+ "",
+ "";
+ };
+};
+
+// I2C6
+// Module 0/1 I2C MUX x3
+&i2c5 {
+ status = "okay";
+ clock-frequency = <400000>;
+ multi-master;
+
+ i2c-mux@71 {
+ compatible = "nxp,pca9546";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x71>;
+ i2c-mux-idle-disconnect;
+
+ imux16: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux17: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ i2c-mux@74 {
+ compatible = "nxp,pca9546";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x74>;
+ i2c-mux-idle-disconnect;
+
+ i2c17mux0: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ i2c17mux1: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ i2c17mux2: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ i2c17mux3: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+ };
+
+ imux18: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux19: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+
+ i2c-mux@72 {
+ compatible = "nxp,pca9546";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x72>;
+ i2c-mux-idle-disconnect;
+
+ imux20: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux21: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ gpio@21 {
+ compatible = "nxp,pca9555";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-line-names =
+ "RST_CX_0_L-O",
+ "RST_CX_1_L-O",
+ "CX0_SSD0_PRSNT_L-I",
+ "CX1_SSD1_PRSNT_L-I",
+ "CX_BOOT_CMPLT_CX0-I",
+ "CX_BOOT_CMPLT_CX1-I",
+ "CX_TWARN_CX0_L-I",
+ "CX_TWARN_CX1_L-I",
+ "CX_OVT_SHDN_CX0-I",
+ "CX_OVT_SHDN_CX1-I",
+ "FNP_L_CX0-O",
+ "FNP_L_CX1-O",
+ "",
+ "MCU_GPIO-I",
+ "MCU_RST_N-O",
+ "MCU_RECOVERY_N-O";
+ };
+ };
+
+ imux22: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux23: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+
+ i2c-mux@73 {
+ compatible = "nxp,pca9546";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x73>;
+ i2c-mux-idle-disconnect;
+
+ imux24: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux25: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ i2c-mux@70 {
+ compatible = "nxp,pca9546";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x70>;
+ i2c-mux-idle-disconnect;
+
+ i2c25mux0: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ i2c25mux1: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ i2c25mux2: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ i2c25mux3: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+ };
+
+ imux26: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux27: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+
+ i2c-mux@75 {
+ compatible = "nxp,pca9546";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x75>;
+ i2c-mux-idle-disconnect;
+
+ imux28: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux29: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ i2c-mux@74 {
+ compatible = "nxp,pca9546";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x74>;
+ i2c-mux-idle-disconnect;
+
+ i2c29mux0: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ i2c29mux1: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ i2c29mux2: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ i2c29mux3: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+ };
+
+ imux30: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux31: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+
+ i2c-mux@76 {
+ compatible = "nxp,pca9546";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x76>;
+ i2c-mux-idle-disconnect;
+
+ imux32: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux33: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ gpio@21 {
+ compatible = "nxp,pca9555";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpio-line-names =
+ "SEC_RST_CX_0_L-O",
+ "SEC_RST_CX_1_L-O",
+ "SEC_CX0_SSD0_PRSNT_L-I",
+ "SEC_CX1_SSD1_PRSNT_L-I",
+ "SEC_CX_BOOT_CMPLT_CX0-I",
+ "SEC_CX_BOOT_CMPLT_CX1-I",
+ "SEC_CX_TWARN_CX0_L-I",
+ "SEC_CX_TWARN_CX1_L-I",
+ "SEC_CX_OVT_SHDN_CX0-I",
+ "SEC_CX_OVT_SHDN_CX1-I",
+ "SEC_FNP_L_CX0-O",
+ "SEC_FNP_L_CX1-O",
+ "",
+ "SEC_MCU_GPIO-I",
+ "SEC_MCU_RST_N-O",
+ "SEC_MCU_RECOVERY_N-O";
+ };
+ };
+
+ imux34: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux35: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+
+ i2c-mux@77 {
+ compatible = "nxp,pca9546";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x77>;
+ i2c-mux-idle-disconnect;
+
+ imux36: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ imux37: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ imux38: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ imux39: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+};
+
+// I2C7
+// Module 0/1 Leak Sensors
+// Module 0/1 Fan Controllers
+&i2c6 {
+ status = "okay";
+ clock-frequency = <400000>;
+ pmic@12 {
+ compatible = "ti,lm5066i";
+ reg = <0x12>;
+ shunt-resistor-micro-ohms = <190>;
+ status = "okay";
+ };
+ pmic@14 {
+ compatible = "ti,lm5066i";
+ reg = <0x14>;
+ shunt-resistor-micro-ohms = <190>;
+ status = "okay";
+ };
+ pwm@20 {
+ compatible = "maxim,max31790";
+ reg = <0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ pwm@23 {
+ compatible = "maxim,max31790";
+ reg = <0x23>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ pwm@2c {
+ compatible = "maxim,max31790";
+ reg = <0x2c>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ pwm@2f {
+ compatible = "maxim,max31790";
+ reg = <0x2f>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
+
+// I2C9
+// M.2
+&i2c8 {
+ status = "okay";
+ clock-frequency = <400000>;
+ multi-master;
+};
+
+// I2C10
+// HMC IO Expander
+// Module 0/1 IO Expanders
+&i2c9 {
+ status = "okay";
+ clock-frequency = <400000>;
+ // Module 0, Expander @0x20
+ exp0: gpio@20 {
+ compatible = "nxp,pca9555";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
+ gpio-line-names =
+ "FPGA_THERM_OVERT_L-I",
+ "FPGA_READY_BMC-I",
+ "HMC_BMC_DETECT-O",
+ "HMC_PGOOD-O",
+ "",
+ "BMC_STBY_CYCLE-O",
+ "FPGA_EROT_FATAL_ERROR_L-I",
+ "WP_HW_EXT_CTRL_L-O",
+ "EROT_FPGA_RST_L-O",
+ "FPGA_EROT_RECOVERY_L-O",
+ "BMC_EROT_FPGA_SPI_MUX_SEL-O",
+ "USB_HUB_RESET_L-O",
+ "NCSI_CS1_SEL-O",
+ "SGPIO_EN_L-O",
+ "B2B_IOEXP_INT_L-I",
+ "I2C_BUS_MUX_RESET_L-O";
+ };
+
+ // Module 1, Expander @0x21
+ exp1: gpio@21 {
+ compatible = "nxp,pca9555";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
+ gpio-line-names =
+ "SEC_FPGA_THERM_OVERT_L-I",
+ "SEC_FPGA_READY_BMC-I",
+ "",
+ "",
+ "",
+ "",
+ "SEC_FPGA_EROT_FATAL_ERROR_L-I",
+ "SEC_WP_HW_EXT_CTRL_L-O",
+ "SEC_EROT_FPGA_RST_L-O",
+ "SEC_FPGA_EROT_RECOVERY_L-O",
+ "SEC_BMC_EROT_FPGA_SPI_MUX_SEL-O",
+ "SEC_USB2_HUB_RST_L-O",
+ "",
+ "",
+ "",
+ "SEC_I2C_BUS_MUX_RESET_L-O";
+ };
+
+ // HMC Expander @0x27
+ exp2: gpio@27 {
+ compatible = "nxp,pca9555";
+ reg = <0x27>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
+ gpio-line-names =
+ "HMC_PRSNT_L-I",
+ "HMC_READY-I",
+ "HMC_EROT_FATAL_ERROR_L-I",
+ "I2C_MUX_SEL-O",
+ "HMC_EROT_SPI_MUX_SEL-O",
+ "HMC_EROT_RECOVERY_L-O",
+ "HMC_EROT_RST_L-O",
+ "GLOBAL_WP_HMC-O",
+ "FPGA_RST_L-O",
+ "USB2_HUB_RST-O",
+ "CPU_UART_MUX_SEL-O",
+ "",
+ "",
+ "",
+ "",
+ "";
+ };
+ // HMC Expander @0x74
+ exp3: gpio@74 {
+ compatible = "nxp,pca9555";
+ reg = <0x74>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
+ gpio-line-names =
+ "IOB_PRSNT_L",
+ "IOB_DP_HPD",
+ "IOX_BMC_RESET",
+ "IOB_IOEXP_INT_L",
+ "IOB_UID_LED_L",
+ "IOB_UID_BTN_L",
+ "IOB_SYS_RST_BTN_L",
+ "IOB_PWR_LED_L",
+ "IOB_PWR_BTN_L",
+ "IOB_PHY_RST",
+ "CPLD_JTAG_MUX_SEL",
+ "",
+ "",
+ "",
+ "",
+ "";
+ };
+};
+
+// I2C11
+// BMC FRU EEPROM
+// BMC Temp Sensor
+&i2c10 {
+ status = "okay";
+ clock-frequency = <400000>;
+ // BMC FRU EEPROM - 256 bytes
+ eeprom@50 {
+ compatible = "atmel,24c02";
+ reg = <0x50>;
+ pagesize = <8>;
+ };
+};
+
+// I2C12
+&i2c11 {
+ status = "disabled";
+};
+
+// I2C13
+&i2c12 {
+ status = "disabled";
+};
+
+// I2C14
+// Module 0 UPHY3 SMBus
+&i2c13 {
+ status = "disabled";
+};
+
+// I2C15
+// Module 1 UPHY3 SMBus
+&i2c14 {
+ status = "okay";
+ clock-frequency = <100000>;
+ multi-master;
+
+ //E1.S drive slot 0-3
+ i2c-mux@77 {
+ compatible = "nxp,pca9546";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x77>;
+ i2c-mux-idle-disconnect;
+
+ e1si2c0: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ e1si2c1: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ e1si2c2: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ e1si2c3: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+};
+
+// I2C16
+&i2c15 {
+ status = "okay";
+ clock-frequency = <100000>;
+ multi-master;
+
+ //E1.S drive slot 4-7
+ i2c-mux@77 {
+ compatible = "nxp,pca9546";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x77>;
+ i2c-mux-idle-disconnect;
+
+ e1si2c4: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+
+ e1si2c5: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+
+ e1si2c6: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ e1si2c7: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+ };
+};
+
+&rng {
+ status = "okay";
+};
+
+&gpio0 {
+ gpio-line-names =
+ /*A0-A7*/ "", "", "", "", "", "", "", "",
+ /*B0-B7*/ "", "", "", "", "", "", "", "",
+ /*C0-C7*/ "SGPIO_I2C_MUX_SEL-O", "", "", "", "", "", "", "",
+ /*D0-D7*/ "", "", "", "UART1_MUX_SEL-O", "", "FPGA_PEX_RST_L-O", "", "",
+ /*E0-E7*/ "RTL8221_PHY_RST_L-O", "RTL8211_PHY_INT_L-I", "", "UART3_MUX_SEL-O",
+ "", "", "", "SGPIO_BMC_EN-O",
+ /*F0-F7*/ "", "", "", "", "", "", "", "",
+ /*G0-G7*/ "", "", "", "", "", "", "", "",
+ /*H0-H7*/ "", "", "", "", "", "", "", "",
+ /*I0-I7*/ "", "", "", "", "", "QSPI2_RST_L-O", "GLOBAL_WP_BMC-O", "BMC_DDR4_TEN-O",
+ /*J0-J7*/ "", "", "", "", "", "", "", "",
+ /*K0-K7*/ "", "", "", "", "", "", "", "",
+ /*L0-L7*/ "", "", "", "", "", "", "", "",
+ /*M0-M7*/ "PCIE_EP_RST_EN-O", "BMC_FRU_WP-O", "HMC_RESET_L-O", "STBY_POWER_EN-O",
+ "STBY_POWER_PG-I", "PCIE_EP_RST_L-O", "", "",
+ /*N0-N7*/ "", "", "", "", "", "", "", "",
+ /*O0-O7*/ "", "", "", "", "", "", "", "",
+ /*P0-P7*/ "", "", "", "", "", "", "", "",
+ /*Q0-Q7*/ "", "", "", "", "", "", "", "",
+ /*R0-R7*/ "", "", "", "", "", "", "", "",
+ /*S0-S7*/ "", "", "", "", "", "", "", "",
+ /*T0-T7*/ "", "", "", "", "", "", "", "",
+ /*U0-U7*/ "", "", "", "", "", "", "", "",
+ /*V0-V7*/ "AP_EROT_REQ-O", "EROT_AP_GNT-I", "", "","PCB_TEMP_ALERT-I", "","", "",
+ /*W0-W7*/ "", "", "", "", "", "", "", "",
+ /*X0-X7*/ "", "", "TPM_MUX_SEL-O", "", "", "", "", "",
+ /*Y0-Y7*/ "", "", "", "EMMC_RST-O", "","", "", "",
+ /*Z0-Z7*/ "BMC_READY-O","", "", "", "", "", "", "";
+};
+
+&gpio1 {
+ /* 36 1.8V GPIOs */
+ gpio-line-names =
+ /*A0-A7*/ "", "", "", "", "", "", "", "",
+ /*B0-B7*/ "", "", "", "", "", "", "IO_EXPANDER_INT_L-I","",
+ /*C0-C7*/ "", "", "", "", "", "", "", "",
+ /*D0-D7*/ "", "", "", "", "", "", "SPI_HOST_TPM_RST_L-O", "SPI_BMC_FPGA_INT_L-I",
+ /*E0-E7*/ "", "", "", "", "", "", "", "";
+};
+
+// EMMC group that excludes WP pin
+&pinctrl {
+ pinctrl_emmcg5_default: emmcg5_default {
+ function = "EMMC";
+ groups = "EMMCG5";
+ };
+};
--
2.25.1
^ permalink raw reply related [flat|nested] 10+ messages in thread* Re: [PATCH v3 0/2] Add device tree for Nvidia's GB200NVL BMC
2025-03-20 16:46 [PATCH v3 0/2] Add device tree for Nvidia's GB200NVL BMC Willie Thai
2025-03-20 16:46 ` [PATCH v3 1/2] ARM: dts: aspeed: " Willie Thai
2025-03-20 16:46 ` [PATCH v3 2/2] dt-bindings: arm: aspeed: add " Willie Thai
@ 2025-03-20 18:26 ` Rob Herring (Arm)
2025-03-21 1:06 ` Andrew Jeffery
2 siblings, 1 reply; 10+ messages in thread
From: Rob Herring (Arm) @ 2025-03-20 18:26 UTC (permalink / raw)
To: Willie Thai
Cc: Paul Menzel, tingkaic, kees, Krzysztof Kozlowski, Mars Yang,
linux-kernel, conor+dt, Andrew Lunn, linux-hardening, andrew,
gpiccoli, linux-aspeed, leohu, openbmc, krzk+dt, dkodihalli, joel,
devicetree, linux-arm-kernel, tony.luck
On Thu, 20 Mar 2025 16:46:31 +0000, Willie Thai wrote:
> The GB200NVL BMC is an Aspeed Ast2600 based BMC
> for Nvidia Blackwell GB200NVL platform.
> Reference to Ast2600 SOC [1].
> Reference to Blackwell GB200NVL Platform [2].
>
> Co-developed-by: Mars Yang <maryang@nvidia.com>
> Signed-off-by: Mars Yang <maryang@nvidia.com>
> Cc: Krzysztof Kozlowski <krzk@kernel.org>
> Cc: Andrew Lunn <andrew@lunn.ch>
> Cc: Rob Herring <robh@kernel.org>
> Cc: Paul Menzel <pmenzel@molgen.mpg.de>
> Link: https://www.aspeedtech.com/server_ast2600/ [1]
> Link: https://nvdam.widen.net/s/wwnsxrhm2w/blackwell-datasheet-3384703 [2]
> Signed-off-by: Willie Thai <wthai@nvidia.com>
> ---
> Changes v1 -> v2:
> - Fix the SOB name [Krzysztof]
> - Fix warnings from scripts/checkpatch.pl run [Krzysztof]
> - Fix DTS coding style [Krzysztof]
> - Move pinctrl override to the bottom [Krzysztof]
> - Drop bootargs [Krzysztof]
> - Follow DTS coding style and change naming for leds node [Krzysztof]
> - Change flash 0 status property [Krzysztof]
> - Change the phy-mode to rgmii [Andrew]
> - Remove the max-speed in mac0 [Andrew]
> - Put gpio line name in one line per group of 8 gpios, but keep some b/c they can exceed length limit [Paul]
> Changes v2 -> v3:
> - Fix missing new line [Krzysztof]
> - Fix missing binding define, adding it in the patch no.1 of this patch set v3 [Krzysztof, Rob]
> - Fix DTS coding style [Krzysztof]
> - Modify nodes name to generic name for: i2c expander pca9546, gpio expander pca9555, power monitor lm5066i, fan controller max31790 [Krzysztof]
> - Skip mac setting and wait till the delay issue in phy-mode fix from Aspeed SOC vendor side [Andrew]
> - Remove i2c-scl-clk-low-timeout-us which is Apseed proprietary property [Mars]
> ---
>
> Willie Thai (2):
> ARM: dts: aspeed: Add device tree for Nvidia's GB200NVL BMC
> dt-bindings: arm: aspeed: add Nvidia's GB200NVL BMC
>
> .../bindings/arm/aspeed/aspeed.yaml | 1 +
> arch/arm/boot/dts/aspeed/Makefile | 1 +
> .../aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dts | 1168 +++++++++++++++++
> 3 files changed, 1170 insertions(+)
> create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dts
>
> --
> 2.25.1
>
>
>
My bot found new DTB warnings on the .dts files added or changed in this
series.
Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.
If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:
pip3 install dtschema --upgrade
New warnings running 'make CHECK_DTBS=y for arch/arm/boot/dts/aspeed/' for 20250320164633.101331-1-wthai@nvidia.com:
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: timer: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/timer/arm,arch_timer.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: /sdram@1e6e0000: failed to match any schema with compatible: ['aspeed,ast2600-sdram-edac', 'syscon']
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: bus@1e600000: compatible: ['aspeed,ast2600-ahbc', 'syscon'] is too long
from schema $id: http://devicetree.org/schemas/bus/aspeed,ast2600-ahbc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: syscon@1e6e2000: 'smp-memram@180' does not match any of the regexes: '^interrupt-controller@[0-9a-f]+$', '^p2a-control@[0-9a-f]+$', '^pinctrl(@[0-9a-f]+)?$', '^silicon-id@[0-9a-f]+$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/mfd/aspeed,ast2x00-scu.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: pinctrl: emmcg5_default:groups:0: 'EMMCG5' is not one of ['ADC0', 'ADC1', 'ADC10', 'ADC11', 'ADC12', 'ADC13', 'ADC14', 'ADC15', 'ADC2', 'ADC3', 'ADC4', 'ADC5', 'ADC6', 'ADC7', 'ADC8', 'ADC9', 'BMCINT', 'EMMCG1', 'EMMCG4', 'EMMCG8', 'ESPI', 'ESPIALT', 'FSI1', 'FSI2', 'FWQSPI', 'FWSPIABR', 'FWSPID', 'FWSPIWP', 'GPIT0', 'GPIT1', 'GPIT2', 'GPIT3', 'GPIT4', 'GPIT5', 'GPIT6', 'GPIT7', 'GPIU0', 'GPIU1', 'GPIU2', 'GPIU3', 'GPIU4', 'GPIU5', 'GPIU6', 'GPIU7', 'HVI3C3', 'HVI3C4', 'I2C1', 'I2C10', 'I2C11', 'I2C12', 'I2C13', 'I2C14', 'I2C15', 'I2C16', 'I2C2', 'I2C3', 'I2C4', 'I2C5', 'I2C6', 'I2C7', 'I2C8', 'I2C9', 'I3C1', 'I3C2', 'I3C3', 'I3C4', 'I3C5', 'I3C6', 'JTAGM', 'LHPD', 'LHSIRQ', 'LPC', 'LPCHC', 'LPCPD', 'LPCPME', 'LPCSMI', 'LSIRQ', 'MACLINK1', 'MACLINK2', 'MACLINK3', 'MACLINK4', 'MDIO1', 'MDIO2', 'MDIO3', 'MDIO4', 'NCSI3', 'NCSI4', 'NCTS1', 'NCTS2', 'NCTS3', 'NCTS4', 'NDCD1', 'NDCD2', 'NDCD3', 'NDCD4', 'NDSR1', 'NDSR2', 'NDSR3', 'NDSR4', 'NDTR1', 'NDTR2', 'NDTR3', 'NDTR4', 'NRI1', 'NRI2', 'NRI3', 'NRI4', 'NRTS1', 'NRTS2', 'NRTS3', 'NRTS4', 'OSCCLK', 'PEWAKE', 'PWM0', 'PWM1', 'PWM10G0', 'PWM10G1', 'PWM11G0', 'PWM11G1', 'PWM12G0', 'PWM12G1', 'PWM13G0', 'PWM13G1', 'PWM14G0', 'PWM14G1', 'PWM15G0', 'PWM15G1', 'PWM2', 'PWM3', 'PWM4', 'PWM5', 'PWM6', 'PWM7', 'PWM8G0', 'PWM8G1', 'PWM9G0', 'PWM9G1', 'QSPI1', 'QSPI2', 'RGMII1', 'RGMII2', 'RGMII3', 'RGMII4', 'RMII1', 'RMII2', 'RMII3', 'RMII4', 'RXD1', 'RXD2', 'RXD3', 'RXD4', 'SALT1', 'SALT10G0', 'SALT10G1', 'SALT11G0', 'SALT11G1', 'SALT12G0', 'SALT12G1', 'SALT13G0', 'SALT13G1', 'SALT14G0', 'SALT14G1', 'SALT15G0', 'SALT15G1', 'SALT16G0', 'SALT16G1', 'SALT2', 'SALT3', 'SALT4', 'SALT5', 'SALT6', 'SALT7', 'SALT8', 'SALT9G0', 'SALT9G1', 'SD1', 'SD2', 'SD3', 'SGPM1', 'SGPM2', 'SGPS1', 'SGPS2', 'SIOONCTRL', 'SIOPBI', 'SIOPBO', 'SIOPWREQ', 'SIOPWRGD', 'SIOS3', 'SIOS5', 'SIOSCI', 'SPI1', 'SPI1ABR', 'SPI1CS1', 'SPI1WP', 'SPI2', 'SPI2CS1', 'SPI2CS2', 'TACH0', 'TACH1', 'TACH10', 'TACH11', 'TACH12', 'TACH13', 'TACH14', 'TACH15', 'TACH2', 'TACH3', 'TACH4', 'TACH5', 'TACH6', 'TACH7', 'TACH8', 'TACH9', 'THRU0', 'THRU1', 'THRU2', 'THRU3', 'TXD1', 'TXD2', 'TXD3', 'TXD4', 'UART10', 'UART11', 'UART12G0', 'UART12G1', 'UART13G0', 'UART13G1', 'UART6', 'UART7', 'UART8', 'UART9', 'USBA', 'USBB', 'VB', 'VGAHS', 'VGAVS', 'WDTRST1', 'WDTRST2', 'WDTRST3', 'WDTRST4']
from schema $id: http://devicetree.org/schemas/pinctrl/aspeed,ast2600-pinctrl.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: /ahb/apb@1e6e0000/syscon@1e6e2000/smp-memram@180: failed to match any schema with compatible: ['aspeed,ast2600-smpmem']
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: /ahb/apb@1e6e0000/syscon@1e6e2000/interrupt-controller@560: failed to match any schema with compatible: ['aspeed,ast2600-scu-ic0']
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: /ahb/apb@1e6e0000/syscon@1e6e2000/interrupt-controller@570: failed to match any schema with compatible: ['aspeed,ast2600-scu-ic1']
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: /ahb/apb@1e6e0000/display@1e6e6000: failed to match any schema with compatible: ['aspeed,ast2600-gfx', 'syscon']
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: adc@1e6e9000: 'interrupts' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/iio/adc/aspeed,ast2600-adc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: adc@1e6e9100: 'interrupts' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/iio/adc/aspeed,ast2600-adc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: crypto@1e6fa000: 'aspeed,ahbc' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/crypto/aspeed,ast2600-acry.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: sdc@1e740000: sdhci@1e740100:compatible: ['aspeed,ast2600-sdhci', 'sdhci'] is too long
from schema $id: http://devicetree.org/schemas/mmc/aspeed,sdhci.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: sdc@1e740000: sdhci@1e740200:compatible: ['aspeed,ast2600-sdhci', 'sdhci'] is too long
from schema $id: http://devicetree.org/schemas/mmc/aspeed,sdhci.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: /ahb/sdc@1e740000/sdhci@1e740100: failed to match any schema with compatible: ['aspeed,ast2600-sdhci', 'sdhci']
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: /ahb/sdc@1e740000/sdhci@1e740200: failed to match any schema with compatible: ['aspeed,ast2600-sdhci', 'sdhci']
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: /ahb/apb@1e780000/timer@1e782000: failed to match any schema with compatible: ['aspeed,ast2600-timer']
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: lpc@1e789000: lpc-snoop@80: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/mfd/aspeed-lpc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: lpc@1e789000: reg-io-width: 4 is not of type 'object'
from schema $id: http://devicetree.org/schemas/mfd/aspeed-lpc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: kcs@24: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: kcs@28: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: kcs@2c: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: kcs@114: 'clocks' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: /ahb/apb@1e780000/lpc@1e789000/lhc@a0: failed to match any schema with compatible: ['aspeed,ast2600-lhc']
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: /ahb/apb@1e780000/lpc@1e789000/ibt@140: failed to match any schema with compatible: ['aspeed,ast2600-ibt-bmc']
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: i2c@80: Unevaluated properties are not allowed ('disable-master' was unexpected)
from schema $id: http://devicetree.org/schemas/i2c/aspeed,i2c.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: gpio@21: '#address-cells', '#size-cells' do not match any of the regexes: '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/gpio/gpio-pca95xx.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: gpio@21: '#address-cells', '#size-cells' do not match any of the regexes: '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/gpio/gpio-pca95xx.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: gpio@21: '#address-cells', '#size-cells' do not match any of the regexes: '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/gpio/gpio-pca95xx.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: pwm@20: '#address-cells', '#size-cells' do not match any of the regexes: '^fan-[0-9]+$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/hwmon/maxim,max31790.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: pwm@23: '#address-cells', '#size-cells' do not match any of the regexes: '^fan-[0-9]+$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/hwmon/maxim,max31790.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: pwm@2c: '#address-cells', '#size-cells' do not match any of the regexes: '^fan-[0-9]+$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/hwmon/maxim,max31790.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: pwm@2f: '#address-cells', '#size-cells' do not match any of the regexes: '^fan-[0-9]+$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/hwmon/maxim,max31790.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: gpio@20: '#address-cells', '#size-cells' do not match any of the regexes: '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/gpio/gpio-pca95xx.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: gpio@21: '#address-cells', '#size-cells' do not match any of the regexes: '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/gpio/gpio-pca95xx.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: gpio@27: '#address-cells', '#size-cells' do not match any of the regexes: '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/gpio/gpio-pca95xx.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: gpio@74: '#address-cells', '#size-cells' do not match any of the regexes: '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/gpio/gpio-pca95xx.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: fsi@1e79b000: compatible: ['aspeed,ast2600-fsi-master', 'fsi-master'] is too long
from schema $id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: /ahb/apb@1e790000/fsi@1e79b000: failed to match any schema with compatible: ['aspeed,ast2600-fsi-master', 'fsi-master']
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: fsi@1e79b100: compatible: ['aspeed,ast2600-fsi-master', 'fsi-master'] is too long
from schema $id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: /ahb/apb@1e790000/fsi@1e79b100: failed to match any schema with compatible: ['aspeed,ast2600-fsi-master', 'fsi-master']
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dtb: /ahb/apb@1e790000/dma-controller@1e79e000: failed to match any schema with compatible: ['aspeed,ast2600-udma']
^ permalink raw reply [flat|nested] 10+ messages in thread