From: Johan Jonker <jbx6244@gmail.com>
To: heiko@sntech.de
Cc: christoph.muellner@theobroma-systems.com,
devicetree@vger.kernel.org, heiko.stuebner@theobroma-systems.com,
kever.yang@rock-chips.com, linux-arm-kernel@lists.infradead.org,
linux-rockchip@lists.infradead.org, mark.rutland@arm.com,
robh+dt@kernel.org, robin.murphy@arm.com
Subject: Re: [PATCH 3/3] arm64: dts: rockchip: add Odroid Advance Go
Date: Sat, 7 Mar 2020 09:36:19 +0100 [thread overview]
Message-ID: <59bdf2c1-79cf-2c45-263e-80a9358c7fdd@gmail.com> (raw)
In-Reply-To: <20200306210922.172346-3-heiko@sntech.de>
Hi Heiko,
The 'heartbeat' led seems to need some changes. The rest is inherited
from px30.dtsi I think. How do you deal with all the compatible
properties names that are normally SoC specific?
Also include all mail lists found with:
./scripts/get_maintainer.pl --nogit-fallback --nogit
linux-kernel@vger.kernel.org
DTC arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dtb
DTC arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dt.yaml
CHECK arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dt.yaml
arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dt.yaml: tsadc:
tsadc-otp-gpio: {'rockchip,pins': [[0, 6, 0, 123]], 'phandle': [[90]]}
is not of type 'array'
arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dt.yaml: usb@ff340000:
'clock-names', 'power-domains' do not match any of the regexes:
'pinctrl-[0-9]+'
arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dt.yaml: usb@ff300000:
'power-domains' does not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dt.yaml: usb@ff350000:
'clock-names', 'power-domains' do not match any of the regexes:
'pinctrl-[0-9]+'
arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dt.yaml: gpio-leds:
'heartbeat' does not match any of the regexes: '(^led-[0-9a-f]$|led)',
'pinctrl-[0-9]+'
arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dt.yaml: usb2-phy@100:
'#phy-cells' is a required property
> From: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
>
> The Odroid Advance Go is a handheld based on Rockchip's rk3326 soc
> with a DSI display and some handheld controls including an analog
> joystick connected to the saradc.
>
> Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
> ---
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> .../boot/dts/rockchip/rk3326-odroid-go2.dts | 544 ++++++++++++++++++
> 2 files changed, 545 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts
>
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index af1e1c3707d0..86c38467d487 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -6,6 +6,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-copperhead-ltk101b4029w.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-evb.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-evb.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-roc-cc.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3326-odroid-go2.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
> diff --git a/arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts b/arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts
> new file mode 100644
> index 000000000000..a16f4a0d1d4d
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts
> @@ -0,0 +1,544 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2019 Hardkernel Co., Ltd
> + * Copyright (c) 2020 Theobroma Systems Design und Consulting GmbH
> + */
> +
> +/dts-v1/;
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/pinctrl/rockchip.h>
> +#include "rk3326.dtsi"
> +
> +/ {
> + model = "ODROID-GO Advance";
> + compatible = "hardkernel,rk3326-odroid-go2", "rockchip,rk3326";
> +
> + chosen {
> + stdout-path = "serial2:115200n8";
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&btn_pins>;
> +
> + /*
> + * *** ODROIDGO2-Advance Switch layoout ***
> + * |------------------------------------------------|
> + * | sw15 sw16 |
> + * |------------------------------------------------|
> + * | sw1 |-------------------| sw8 |
> + * | sw3 sw4 | | sw7 sw5 |
> + * | sw2 | LCD Display | sw6 |
> + * | | | |
> + * | |-------------------| |
> + * | sw9 sw10 sw11 sw12 sw13 sw14 |
> + * |------------------------------------------------|
> + */
> +
> + sw1 {
> + gpios = <&gpio1 RK_PB4 GPIO_ACTIVE_LOW>;
> + label = "DPAD-UP";
> + linux,code = <BTN_DPAD_UP>;
> + };
> + sw2 {
> + gpios = <&gpio1 RK_PB5 GPIO_ACTIVE_LOW>;
> + label = "DPAD-DOWN";
> + linux,code = <BTN_DPAD_DOWN>;
> + };
> + sw3 {
> + gpios = <&gpio1 RK_PB6 GPIO_ACTIVE_LOW>;
> + label = "DPAD-LEFT";
> + linux,code = <BTN_DPAD_LEFT>;
> + };
> + sw4 {
> + gpios = <&gpio1 RK_PB7 GPIO_ACTIVE_LOW>;
> + label = "DPAD-RIGHT";
> + linux,code = <BTN_DPAD_RIGHT>;
> + };
> + sw5 {
> + gpios = <&gpio1 RK_PA2 GPIO_ACTIVE_LOW>;
> + label = "BTN-A";
> + linux,code = <BTN_EAST>;
> + };
> + sw6 {
> + gpios = <&gpio1 RK_PA5 GPIO_ACTIVE_LOW>;
> + label = "BTN-B";
> + linux,code = <BTN_SOUTH>;
> + };
> + sw7 {
> + gpios = <&gpio1 RK_PA6 GPIO_ACTIVE_LOW>;
> + label = "BTN-Y";
> + linux,code = <BTN_WEST>;
> + };
> + sw8 {
> + gpios = <&gpio1 RK_PA7 GPIO_ACTIVE_LOW>;
> + label = "BTN-X";
> + linux,code = <BTN_NORTH>;
> + };
> + sw9 {
> + gpios = <&gpio2 RK_PA0 GPIO_ACTIVE_LOW>;
> + label = "F1";
> + linux,code = <BTN_TRIGGER_HAPPY1>;
> + };
> + sw10 {
> + gpios = <&gpio2 RK_PA1 GPIO_ACTIVE_LOW>;
> + label = "F2";
> + linux,code = <BTN_TRIGGER_HAPPY2>;
> + };
> + sw11 {
> + gpios = <&gpio2 RK_PA2 GPIO_ACTIVE_LOW>;
> + label = "F3";
> + linux,code = <BTN_TRIGGER_HAPPY3>;
> + };
> + sw12 {
> + gpios = <&gpio2 RK_PA3 GPIO_ACTIVE_LOW>;
> + label = "F4";
> + linux,code = <BTN_TRIGGER_HAPPY4>;
> + };
> + sw13 {
> + gpios = <&gpio2 RK_PA4 GPIO_ACTIVE_LOW>;
> + label = "F5";
> + linux,code = <BTN_TRIGGER_HAPPY5>;
> + };
> + sw14 {
> + gpios = <&gpio2 RK_PA5 GPIO_ACTIVE_LOW>;
> + label = "F6";
> + linux,code = <BTN_TRIGGER_HAPPY6>;
> + };
> + sw15 {
> + gpios = <&gpio2 RK_PA6 GPIO_ACTIVE_LOW>;
> + label = "TOP-LEFT";
> + linux,code = <BTN_TL>;
> + };
> + sw16 {
> + gpios = <&gpio2 RK_PA7 GPIO_ACTIVE_LOW>;
> + label = "TOP-RIGHT";
> + linux,code = <BTN_TR>;
> + };
> + };
> +
> + leds: gpio-leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "led_pins";
> + pinctrl-0 = <&led_pins>;
> +
> + /* Blue LED : GPIO0_C1 */
> + heartbeat {
> + label = "blue:heartbeat";
> + gpios = <&gpio0 RK_PC1 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + power-supply = <&vcc_bl>;
> + pwms = <&pwm1 0 25000 0>;
> + };
sort nodenames
> +
> + vccsys: vccsys {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc3v8_sys";
> + regulator-always-on;
> + regulator-min-microvolt = <3800000>;
> + regulator-max-microvolt = <3800000>;
> + };
> +
> + vcc_host: vcc_host {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_host";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> +
> + gpio = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + vin-supply = <&vccsys>;
> + };
> +};
> +
> +&cpu0 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cpu1 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cpu2 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cpu3 {
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cru {
> + assigned-clocks = <&cru PLL_NPLL>,
> + <&cru ACLK_BUS_PRE>, <&cru ACLK_PERI_PRE>,
> + <&cru HCLK_BUS_PRE>, <&cru HCLK_PERI_PRE>,
> + <&cru PCLK_BUS_PRE>, <&cru SCLK_GPU>,
> + <&cru PLL_CPLL>;
> +
> + assigned-clock-rates = <1188000000>,
> + <200000000>, <200000000>,
> + <150000000>, <150000000>,
> + <100000000>, <200000000>,
> + <17000000>;
> +};
> +
> +&display_subsystem {
> + status = "okay";
> +};
> +
> +&dsi {
> + status = "okay";
> +
> + ports {
> + mipi_out: port@1 {
> + reg = <1>;
> +
> + mipi_out_panel: endpoint {
> + remote-endpoint = <&mipi_in_panel>;
> + };
> + };
> + };
> +
> + panel@0 {
> + compatible = "elida,kd35t133";
> + reg = <0>;
> + backlight = <&backlight>;
> + iovcc-supply = <&vcc_lcd>;
> + reset-gpios = <&gpio3 RK_PC0 GPIO_ACTIVE_LOW>;
> + vdd-supply = <&vcc_lcd>;
> +
> + port {
> + mipi_in_panel: endpoint {
> + remote-endpoint = <&mipi_out_panel>;
> + };
> + };
> + };
> +};
> +
> +&dsi_dphy {
> + status = "okay";
> +};
> +
> +&gpu {
> + mali-supply = <&vdd_logic>;
> + status = "okay";
> +};
> +
> +&i2c0 {
> + status = "okay";
status below
> + clock-frequency = <400000>;
> + i2c-scl-rising-time-ns = <280>;
> + i2c-scl-falling-time-ns = <16>;
sort
> +
> + rk817: pmic@20 {
> + compatible = "rockchip,rk817";
> + reg = <0x20>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <RK_PB2 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_int>;
> + rockchip,system-power-controller;
> + wakeup-source;
> + #clock-cells = <1>;
> + clock-output-names = "rk808-clkout1", "xin32k";
> +
> + vcc1-supply = <&vccsys>;
> + vcc2-supply = <&vccsys>;
> + vcc3-supply = <&vccsys>;
> + vcc4-supply = <&vccsys>;
> + vcc5-supply = <&vccsys>;
> + vcc6-supply = <&vccsys>;
> + vcc7-supply = <&vccsys>;
> +
> + regulators {
> + vdd_logic: DCDC_REG1 {
> + regulator-name = "vdd_logic";
> + regulator-min-microvolt = <950000>;
> + regulator-max-microvolt = <1150000>;
> + regulator-ramp-delay = <6001>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <950000>;
> + };
> + };
> +
> + vdd_arm: DCDC_REG2 {
> + regulator-name = "vdd_arm";
> + regulator-min-microvolt = <950000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <6001>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + regulator-suspend-microvolt = <950000>;
> + };
> + };
> +
> + vcc_ddr: DCDC_REG3 {
> + regulator-name = "vcc_ddr";
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_3v3: DCDC_REG4 {
> + regulator-name = "vcc_3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vcc_1v8: LDO_REG2 {
> + regulator-name = "vcc_1v8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vdd_1v0: LDO_REG3 {
> + regulator-name = "vdd_1v0";
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1000000>;
> + };
> + };
> +
> + vcc3v3_pmu: LDO_REG4 {
> + regulator-name = "vcc3v3_pmu";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vccio_sd: LDO_REG5 {
> + regulator-name = "vccio_sd";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vcc_sd: LDO_REG6 {
> + regulator-name = "vcc_sd";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vcc_bl: LDO_REG7 {
> + regulator-name = "vcc_bl";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vcc_lcd: LDO_REG8 {
> + regulator-name = "vcc_lcd";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + regulator-suspend-microvolt = <2800000>;
> + };
> + };
> +
> + vcc_cam: LDO_REG9 {
> + regulator-name = "vcc_cam";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + regulator-suspend-microvolt = <3000000>;
> + };
> + };
> + };
> + };
> +};
> +
> +/* EXT Header(P2) : 7(SCL:GPIO0.C2), 8(SDA:GPIO0.C3) */
> +&i2c1 {
> + status = "okay";
status below
> + clock-frequency = <400000>;
> +};
> +
> +/* I2S 1 Channel Used */
> +&i2s1_2ch {
> + status = "okay";
status below
> + #sound-dai-cells = <0>;
> +};
> +
> +&io_domains {
> + vccio1-supply = <&vcc_3v3>;
> + vccio2-supply = <&vccio_sd>;
> + vccio3-supply = <&vcc_3v3>;
> + vccio4-supply = <&vcc_3v3>;
> + vccio5-supply = <&vcc_3v3>;
> + vccio6-supply = <&vcc_3v3>;
> + status = "okay";
> +};
> +
> +&pmu_io_domains {
> + pmuio1-supply = <&vcc3v3_pmu>;
> + pmuio2-supply = <&vcc3v3_pmu>;
> + status = "okay";
> +};
> +
> +&pwm1 {
> + status = "okay";
> +};
> +
> +&saradc {
> + vref-supply = <&vcc_1v8>;
> + status = "okay";
> +};
> +
> +&sdmmc {
> + bus-width = <4>;
> + cap-sd-highspeed;
> + card-detect-delay = <800>;
Other dts use 200. Why we need 800?
> + cd-gpios = <&gpio0 RK_PA3 GPIO_ACTIVE_LOW>;
> + sd-uhs-sdr12;
> + sd-uhs-sdr25;
> + sd-uhs-sdr50;
> + sd-uhs-sdr104;
> + vmmc-supply = <&vcc_sd>;
> + vqmmc-supply = <&vccio_sd>;
> + status = "okay";
> +};
> +
> +&tsadc {
> + pinctrl-names = "gpio", "otpout";
> + pinctrl-0 = <&tsadc_otp_gpio>;
> + pinctrl-1 = <&tsadc_otp_out>;
> + status = "okay";
> +};
> +
> +&u2phy {
> + status = "okay";
> +
> + u2phy_host: host-port {
> + status = "okay";
> + };
> +
> + u2phy_otg: otg-port {
> + status = "disabled";
> + };
> +};
> +
> +&usb20_otg {
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart1_xfer &uart1_cts>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart2m1_xfer>;
> + status = "okay";
> +};
> +
> +&vopb {
> + status = "okay";
> +};
> +
> +&vopb_mmu {
> + status = "okay";
> +};
> +
> +&pinctrl {
> + pmic {
> + pmic_int: pmic-int {
> + rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> +
> + dc_det: dc-det {
> + rockchip,pins = <0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + leds {
> + led_pins: led-pins {
> + rockchip,pins = <0 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + btns {
> + btn_pins: btn-pins {
> + rockchip,pins = <1 RK_PB4 RK_FUNC_GPIO &pcfg_pull_up>,
> + <1 RK_PB5 RK_FUNC_GPIO &pcfg_pull_up>,
> + <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_up>,
> + <1 RK_PB7 RK_FUNC_GPIO &pcfg_pull_up>,
> + <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>,
> + <1 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>,
> + <1 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>,
> + <1 RK_PA7 RK_FUNC_GPIO &pcfg_pull_up>,
> +
> + <2 RK_PA0 RK_FUNC_GPIO &pcfg_pull_up>,
> + <2 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>,
> + <2 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>,
> + <2 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>,
> + <2 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>,
> + <2 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>,
> + <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>,
> + <2 RK_PA7 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +};
> --
> 2.24.1
next prev parent reply other threads:[~2020-03-07 8:36 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-03-06 21:09 [PATCH 1/3] arm64: dts: rockchip: add core devicetree for rk3326 Heiko Stuebner
2020-03-06 21:09 ` [PATCH 2/3] dt-bindings: Add binding for Hardkernel Odroid Go Advance Heiko Stuebner
2020-03-06 21:09 ` [PATCH 3/3] arm64: dts: rockchip: add Odroid Advance Go Heiko Stuebner
2020-03-07 8:36 ` Johan Jonker [this message]
2020-03-07 13:47 ` Heiko Stübner
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=59bdf2c1-79cf-2c45-263e-80a9358c7fdd@gmail.com \
--to=jbx6244@gmail.com \
--cc=christoph.muellner@theobroma-systems.com \
--cc=devicetree@vger.kernel.org \
--cc=heiko.stuebner@theobroma-systems.com \
--cc=heiko@sntech.de \
--cc=kever.yang@rock-chips.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-rockchip@lists.infradead.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=robin.murphy@arm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).