[PATCH v5 3/4] arm64: dts: add description for solidrun cn9130 som and clearfog boards

Josua Mayer
2024-05-09T10:46:22Z

Add description for the SolidRun CN9130 SoM, and Clearfog Base / Pro
reference boards.

The SoM has been designed as a pin-compatible replacement for the older
Armada 388 based SoM. Therefore it supports the same boards and a
similar feature set.

Most notable upgrades:
- 4x Cortex-A72
- 10Gbps SFP
- Both eMMC and SD supported at the same time

The developer first supporting this product at SolidRun decided to use
different filenames for the DTBs: Armada 388 uses the full
"clearfog" string while cn9130 uses the abbreviation "cf".
This name is already hard-coded in pre-installed vendor u-boot and can
not be changed easily.

NOTICE IN CASE ANYBODY WANTS TO SELF-UPGRADE:
CN9130 SoM has a different footprint from Armada 388 SoM.
Components on the carrier board below the SoM may collide causing
damage, such as on Clearfog Base.

Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
arch/arm64/boot/dts/marvell/Makefile | 2 +
arch/arm64/boot/dts/marvell/cn9130-cf-base.dts | 178 ++++++++++++
arch/arm64/boot/dts/marvell/cn9130-cf-pro.dts | 375 +++++++++++++++++++++++++
arch/arm64/boot/dts/marvell/cn9130-cf.dtsi | 197 +++++++++++++
arch/arm64/boot/dts/marvell/cn9130-sr-som.dtsi | 160 +++++++++++
5 files changed, 912 insertions(+)

diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index 99b8cb3c49e1..019f2251d696 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -28,3 +28,5 @@ dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-A.dtb
dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-B.dtb
dtb-$(CONFIG_ARCH_MVEBU) += ac5x-rd-carrier-cn9131.dtb
dtb-$(CONFIG_ARCH_MVEBU) += ac5-98dx35xx-rd.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += cn9130-cf-base.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += cn9130-cf-pro.dtb
diff --git a/arch/arm64/boot/dts/marvell/cn9130-cf-base.dts b/arch/arm64/boot/dts/marvell/cn9130-cf-base.dts
new file mode 100644
index 000000000000..788a5c302b17
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9130-cf-base.dts
@@ -0,0 +1,178 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2024 Josua Mayer <josua@solid-run.com>
+ *
+ * DTS for SolidRun CN9130 Clearfog Base.
+ *
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+#include "cn9130.dtsi"
+#include "cn9130-sr-som.dtsi"
+#include "cn9130-cf.dtsi"
+
+/ {
+ model = "SolidRun CN9130 Clearfog Base";
+ compatible = "solidrun,cn9130-clearfog-base",
+ "solidrun,cn9130-sr-som", "marvell,cn9130";
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&rear_button_pins>;
+ pinctrl-names = "default";
+
+ button-0 {
+ /* The rear SW3 button */
+ label = "Rear Button";
+ gpios = <&cp0_gpio1 31 GPIO_ACTIVE_LOW>;
+ linux,can-disable;
+ linux,code = <BTN_0>;
+ };
+ };
+
+ rfkill-m2-gnss {
+ compatible = "rfkill-gpio";
+ label = "m.2 GNSS";
+ radio-type = "gps";
+ /* rfkill-gpio inverts internally */
+ shutdown-gpios = <&expander0 9 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* M.2 is B-keyed, so w-disable is for WWAN */
+ rfkill-m2-wwan {
+ compatible = "rfkill-gpio";
+ label = "m.2 WWAN";
+ radio-type = "wwan";
+ /* rfkill-gpio inverts internally */
+ shutdown-gpios = <&expander0 8 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+/* SRDS #3 - SGMII 1GE */
+&cp0_eth1 {
+ phy = <&phy1>;
+ phys = <&cp0_comphy3 1>;
+ phy-mode = "sgmii";
+ status = "okay";
+};
+
+&cp0_eth2_phy {
+ /*
+ * Configure LEDs default behaviour:
+ * - LED[0]: link/activity: On/blink (green)
+ * - LED[1]: link is 100/1000Mbps: On (yellow)
+ * - LED[2]: high impedance (floating)
+ */
+ marvell,reg-init = <3 16 0xf000 0x0a61>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_WAN;
+ default-state = "keep";
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_YELLOW>;
+ function = LED_FUNCTION_WAN;
+ default-state = "keep";
+ };
+ };
+};
+
+&cp0_gpio1 {
+ sim-select-hog {
+ gpio-hog;
+ gpios = <27 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "sim-select";
+ };
+};
+
+&cp0_mdio {
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ /*
+ * Configure LEDs default behaviour:
+ * - LED[0]: link/activity: On/blink (green)
+ * - LED[1]: link is 100/1000Mbps: On (yellow)
+ * - LED[2]: high impedance (floating)
+ *
+ * Configure LEDs electrical polarity
+ * - on-state: low
+ * - off-state: high (not hi-z, to avoid residual glow)
+ */
+ marvell,reg-init = <3 16 0xf000 0x0a61>,
+ <3 17 0x003f 0x000a>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_YELLOW>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+ };
+ };
+};
+
+&cp0_pinctrl {
+ pinctrl-0 = <&sim_select_pins>;
+ pintrl-names = "default";
+
+ rear_button_pins: cp0-rear-button-pins {
+ marvell,pins = "mpp31";
+ marvell,function = "gpio";
+ };
+
+ sim_select_pins: cp0-sim-select-pins {
+ marvell,pins = "mpp27";
+ marvell,function = "gpio";
+ };
+};
+
+/*
+ * SRDS #4 - USB 3.0 host on M.2 connector
+ * USB-2.0 Host on Type-A connector
+ */
+&cp0_usb3_1 {
+ phys = <&cp0_comphy4 1>, <&cp0_utmi1>;
+ phy-names = "comphy", "utmi";
+ dr_mode = "host";
+ status = "okay";
+};
+
+&expander0 {
+ m2-full-card-power-off-hog {
+ gpio-hog;
+ gpios = <2 GPIO_ACTIVE_LOW>;
+ output-low;
+ line-name = "m2-full-card-power-off";
+ };
+
+ m2-reset-hog {
+ gpio-hog;
+ gpios = <10 GPIO_ACTIVE_LOW>;
+ output-low;
+ line-name = "m2-reset";
+ };
+};
diff --git a/arch/arm64/boot/dts/marvell/cn9130-cf-pro.dts b/arch/arm64/boot/dts/marvell/cn9130-cf-pro.dts
new file mode 100644
index 000000000000..a27fe0042867
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9130-cf-pro.dts
@@ -0,0 +1,375 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2024 Josua Mayer <josua@solid-run.com>
+ *
+ * DTS for SolidRun CN9130 Clearfog Pro.
+ *
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+#include "cn9130.dtsi"
+#include "cn9130-sr-som.dtsi"
+#include "cn9130-cf.dtsi"
+
+/ {
+ model = "SolidRun CN9130 Clearfog Pro";
+ compatible = "solidrun,cn9130-clearfog-pro",
+ "solidrun,cn9130-sr-som", "marvell,cn9130";
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&rear_button_pins>;
+ pinctrl-names = "default";
+
+ button-0 {
+ /* The rear SW3 button */
+ label = "Rear Button";
+ gpios = <&cp0_gpio2 0 GPIO_ACTIVE_LOW>;
+ linux,can-disable;
+ linux,code = <BTN_0>;
+ };
+ };
+};
+
+/* SRDS #3 - SGMII 1GE to L2 switch */
+&cp0_eth1 {
+ phys = <&cp0_comphy3 1>;
+ phy-mode = "sgmii";
+ status = "okay";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&cp0_eth2_phy {
+ /*
+ * Configure LEDs default behaviour similar to switch ports:
+ * - LED[0]: link/activity: On/blink (green)
+ * - LED[1]: link is 100/1000Mbps: On (red)
+ * - LED[2]: high impedance (floating)
+ *
+ * Switch port defaults:
+ * - LED0: link/activity: On/blink (green)
+ * - LED1: link is 1000Mbps: On (red)
+ *
+ * Identical configuration is impossible with hardware offload.
+ */
+ marvell,reg-init = <3 16 0xf000 0x0a61>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_WAN;
+ label = "LED2";
+ default-state = "keep";
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_WAN;
+ label = "LED1";
+ default-state = "keep";
+ };
+ };
+};
+
+&cp0_mdio {
+ ethernet-switch@4 {
+ compatible = "marvell,mv88e6085";
+ reg = <4>;
+ pinctrl-0 = <&dsa_clk_pins &dsa_pins>;
+ pinctrl-names = "default";
+ reset-gpios = <&cp0_gpio1 27 GPIO_ACTIVE_LOW>;
+ interrupt-parent = <&cp0_gpio1>;
+ interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet-port@0 {
+ reg = <0>;
+ label = "lan5";
+ phy = <&switch0phy0>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ label = "LED12";
+ default-state = "keep";
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_LAN;
+ label = "LED11";
+ default-state = "keep";
+ };
+ };
+ };
+
+ ethernet-port@1 {
+ reg = <1>;
+ label = "lan4";
+ phy = <&switch0phy1>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ label = "LED10";
+ default-state = "keep";
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_LAN;
+ label = "LED9";
+ default-state = "keep";
+ };
+ };
+ };
+
+ ethernet-port@2 {
+ reg = <2>;
+ label = "lan3";
+ phy = <&switch0phy2>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ label = "LED8";
+ default-state = "keep";
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_LAN;
+ label = "LED7";
+ default-state = "keep";
+ };
+ };
+ };
+
+ ethernet-port@3 {
+ reg = <3>;
+ label = "lan2";
+ phy = <&switch0phy3>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ label = "LED6";
+ default-state = "keep";
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_LAN;
+ label = "LED5";
+ default-state = "keep";
+ };
+ };
+ };
+
+ ethernet-port@4 {
+ reg = <4>;
+ label = "lan1";
+ phy = <&switch0phy4>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ label = "LED4";
+ default-state = "keep";
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_LAN;
+ label = "LED3";
+ default-state = "keep";
+ };
+ };
+ };
+
+ ethernet-port@5 {
+ reg = <5>;
+ label = "cpu";
+ ethernet = <&cp0_eth1>;
+ phy-mode = "sgmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ ethernet-port@6 {
+ reg = <6>;
+ label = "lan6";
+ phy-mode = "rgmii";
+
+ /*
+ * Because of mdio address conflict the
+ * external phy is not readable.
+ * Force a fixed link instead.
+ */
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch0phy0: ethernet-phy@0 {
+ reg = <0x0>;
+ };
+
+ switch0phy1: ethernet-phy@1 {
+ reg = <0x1>;
+ /*
+ * Indirectly configure default behaviour
+ * for port lan6 leds behind external phy.
+ * Internal PHYs are not using page 3,
+ * therefore writing to it is safe.
+ */
+ marvell,reg-init = <3 16 0xf000 0x0a61>;
+ };
+
+ switch0phy2: ethernet-phy@2 {
+ reg = <0x2>;
+ };
+
+ switch0phy3: ethernet-phy@3 {
+ reg = <0x3>;
+ };
+
+ switch0phy4: ethernet-phy@4 {
+ reg = <0x4>;
+ };
+ };
+
+ /*
+ * There is an external phy on the switch mdio bus.
+ * Because its mdio address collides with internal phys,
+ * it is not readable.
+ *
+ * mdio-external {
+ * compatible = "marvell,mv88e6xxx-mdio-external";
+ * #address-cells = <1>;
+ * #size-cells = <0>;
+ *
+ * ethernet-phy@1 {
+ * reg = <0x1>;
+ * };
+ * };
+ */
+ };
+};
+
+/* SRDS #4 - miniPCIe (CON2) */
+&cp0_pcie1 {
+ num-lanes = <1>;
+ phys = <&cp0_comphy4 1>;
+ /* dw-pcie inverts internally */
+ reset-gpios = <&expander0 2 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&cp0_pinctrl {
+ dsa_clk_pins: cp0-dsa-clk-pins {
+ marvell,pins = "mpp40";
+ marvell,function = "synce1";
+ };
+
+ dsa_pins: cp0-dsa-pins {
+ marvell,pins = "mpp27", "mpp29";
+ marvell,function = "gpio";
+ };
+
+ rear_button_pins: cp0-rear-button-pins {
+ marvell,pins = "mpp32";
+ marvell,function = "gpio";
+ };
+
+ cp0_spi1_cs1_pins: cp0-spi1-cs1-pins {
+ marvell,pins = "mpp12";
+ marvell,function = "spi1";
+ };
+};
+
+&cp0_spi1 {
+ /* add pin for chip-select 1 on mikrobus */
+ pinctrl-0 = <&cp0_spi1_pins &cp0_spi1_cs1_pins>;
+};
+
+/* USB-2.0 Host on Type-A connector */
+&cp0_usb3_1 {
+ phys = <&cp0_utmi1>;
+ phy-names = "utmi";
+ dr_mode = "host";
+ status = "okay";
+};
+
+&expander0 {
+ /* CON2 */
+ pcie1-0-clkreq-hog {
+ gpio-hog;
+ gpios = <4 GPIO_ACTIVE_LOW>;
+ input;
+ line-name = "pcie1.0-clkreq";
+ };
+
+ /* CON2 */
+ pcie1-0-w-disable-hog {
+ gpio-hog;
+ gpios = <7 GPIO_ACTIVE_LOW>;
+ output-low;
+ line-name = "pcie1.0-w-disable";
+ };
+};
diff --git a/arch/arm64/boot/dts/marvell/cn9130-cf.dtsi b/arch/arm64/boot/dts/marvell/cn9130-cf.dtsi
new file mode 100644
index 000000000000..ad0ab34b6602
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9130-cf.dtsi
@@ -0,0 +1,197 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2024 Josua Mayer <josua@solid-run.com>
+ *
+ * DTS for common base of SolidRun CN9130 Clearfog Base and Pro.
+ *
+ */
+
+/ {
+ aliases {
+ /* label nics same order as armada 388 clearfog */
+ ethernet0 = &cp0_eth2;
+ ethernet1 = &cp0_eth1;
+ ethernet2 = &cp0_eth0;
+ i2c1 = &cp0_i2c1;
+ mmc1 = &cp0_sdhci0;
+ };
+
+ reg_usb3_vbus0: regulator-usb3-vbus0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vbus0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpios = <&expander0 6 GPIO_ACTIVE_LOW>;
+ };
+
+ sfp: sfp {
+ compatible = "sff,sfp";
+ i2c-bus = <&cp0_i2c1>;
+ los-gpios = <&expander0 12 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&expander0 15 GPIO_ACTIVE_LOW>;
+ tx-disable-gpios = <&expander0 14 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpios = <&expander0 13 GPIO_ACTIVE_HIGH>;
+ maximum-power-milliwatt = <2000>;
+ };
+};
+
+/* SRDS #2 - SFP+ 10GE */
+&cp0_eth0 {
+ managed = "in-band-status";
+ phys = <&cp0_comphy2 0>;
+ phy-mode = "10gbase-r";
+ sfp = <&sfp>;
+ status = "okay";
+};
+
+&cp0_i2c0 {
+ expander0: gpio-expander@20 {
+ compatible = "nxp,pca9555";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ pinctrl-0 = <&expander0_pins>;
+ pinctrl-names = "default";
+ interrupt-parent = <&cp0_gpio1>;
+ interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+
+ /* CON3 */
+ pcie2-0-clkreq-hog {
+ gpio-hog;
+ gpios = <0 GPIO_ACTIVE_LOW>;
+ input;
+ line-name = "pcie2.0-clkreq";
+ };
+
+ /* CON3 */
+ pcie2-0-w-disable-hog {
+ gpio-hog;
+ gpios = <3 GPIO_ACTIVE_LOW>;
+ output-low;
+ line-name = "pcie2.0-w-disable";
+ };
+
+ usb3-ilimit-hog {
+ gpio-hog;
+ gpios = <5 GPIO_ACTIVE_LOW>;
+ input;
+ line-name = "usb3-current-limit";
+ };
+
+ m2-devslp-hog {
+ gpio-hog;
+ gpios = <11 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "m.2 devslp";
+ };
+ };
+
+ /* The MCP3021 supports standard and fast modes */
+ adc@4c {
+ compatible = "microchip,mcp3021";
+ reg = <0x4c>;
+ };
+
+ carrier_eeprom: eeprom@52 {
+ compatible = "atmel,24c02";
+ reg = <0x52>;
+ pagesize = <8>;
+ };
+};
+
+&cp0_i2c1 {
+ /*
+ * Routed to SFP, M.2, mikrobus, and miniPCIe
+ * SFP limits this to 100kHz, and requires an AT24C01A/02/04 with
+ * address pins tied low, which takes addresses 0x50 and 0x51.
+ * Mikrobus doesn't specify beyond an I2C bus being present.
+ * PCIe uses ARP to assign addresses, or 0x63-0x64.
+ */
+ clock-frequency = <100000>;
+ pinctrl-0 = <&cp0_i2c1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+/* SRDS #5 - miniPCIe (CON3) */
+&cp0_pcie2 {
+ num-lanes = <1>;
+ phys = <&cp0_comphy5 2>;
+ /* dw-pcie inverts internally */
+ reset-gpios = <&expander0 1 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&cp0_pinctrl {
+ cp0_i2c1_pins: cp0-i2c1-pins {
+ marvell,pins = "mpp35", "mpp36";
+ marvell,function = "i2c1";
+ };
+
+ cp0_mmc0_pins: cp0-mmc0-pins {
+ marvell,pins = "mpp43", "mpp56", "mpp57", "mpp58",
+ "mpp59", "mpp60", "mpp61";
+ marvell,function = "sdio";
+ };
+
+ mikro_spi_pins: cp0-spi1-cs1-pins {
+ marvell,pins = "mpp12";
+ marvell,function = "spi1";
+ };
+
+ mikro_uart_pins: cp0-uart-pins {
+ marvell,pins = "mpp2", "mpp3";
+ marvell,function = "uart1";
+ };
+
+ expander0_pins: cp0-expander0-pins {
+ marvell,pins = "mpp4";
+ marvell,function = "gpio";
+ };
+};
+
+/* SRDS #0 - SATA on M.2 connector */
+&cp0_sata0 {
+ phys = <&cp0_comphy0 1>;
+ status = "okay";
+
+ /* only port 1 is available */
+ /delete-node/ sata-port@0;
+};
+
+/* microSD */
+&cp0_sdhci0 {
+ pinctrl-0 = <&cp0_mmc0_pins>;
+ pinctrl-names = "default";
+ bus-width = <4>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&cp0_spi1 {
+ /* CS1 for mikrobus */
+ pinctrl-0 = <&cp0_spi1_pins &mikro_spi_pins>;
+};
+
+/*
+ * SRDS #1 - USB-3.0 Host on Type-A connector
+ * USB-2.0 Host on mPCI-e connector (CON3)
+ */
+&cp0_usb3_0 {
+ phys = <&cp0_comphy1 0>, <&cp0_utmi0>;
+ phy-names = "comphy", "utmi";
+ vbus-supply = <&reg_usb3_vbus0>;
+ dr_mode = "host";
+ status = "okay";
+};
+
+&cp0_utmi {
+ status = "okay";
+};
+
+/* mikrobus uart */
+&cp0_uart0 {
+ pinctrl-0 = <&mikro_uart_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/marvell/cn9130-sr-som.dtsi b/arch/arm64/boot/dts/marvell/cn9130-sr-som.dtsi
new file mode 100644
index 000000000000..4676e3488f54
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9130-sr-som.dtsi
@@ -0,0 +1,160 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2024 Josua Mayer <josua@solid-run.com>
+ *
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "SolidRun CN9130 SoM";
+ compatible = "solidrun,cn9130-sr-som", "marvell,cn9130";
+
+ aliases {
+ ethernet0 = &cp0_eth0;
+ ethernet1 = &cp0_eth1;
+ ethernet2 = &cp0_eth2;
+ i2c0 = &cp0_i2c0;
+ mmc0 = &ap_sdhci0;
+ rtc0 = &cp0_rtc;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ v_1_8: regulator-1-8 {
+ compatible = "regulator-fixed";
+ regulator-name = "1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ /* requires assembly of R9307 */
+ vhv: regulator-vhv-1-8 {
+ compatible = "regulator-fixed";
+ regulator-name = "vhv-1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ pinctrl-0 = <&cp0_reg_vhv_pins>;
+ pinctrl-names = "default";
+ gpios = <&cp0_gpio2 9 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&ap_pinctrl {
+ ap_mmc0_pins: ap-mmc0-pins {
+ marvell,pins = "mpp0", "mpp1", "mpp2", "mpp3", "mpp4", "mpp5",
+ "mpp6", "mpp7", "mpp8", "mpp9", "mpp10", "mpp12";
+ marvell,function = "sdio";
+ /*
+ * mpp12 is emmc reset, function should be sdio (hw_rst),
+ * but pinctrl-mvebu does not support this.
+ *
+ * From pinctrl-mvebu.h:
+ * "The name will be used to switch to this setting in DT description, e.g.
+ * marvell,function = "uart2". subname is only for debugging purposes."
+ */
+ };
+};
+
+&ap_sdhci0 {
+ bus-width = <8>;
+ pinctrl-0 = <&ap_mmc0_pins>;
+ pinctrl-names = "default";
+ vqmmc-supply = <&v_1_8>;
+ status = "okay";
+};
+
+&cp0_ethernet {
+ status = "okay";
+};
+
+/* for assembly with phy */
+&cp0_eth2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_eth2_pins>;
+ phy-mode = "rgmii-id";
+ phy = <&cp0_eth2_phy>;
+ status = "okay";
+};
+
+&cp0_i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_i2c0_pins>;
+ clock-frequency = <100000>;
+ status = "okay";
+
+ som_eeprom: eeprom@53 {
+ compatible = "atmel,24c02";
+ reg = <0x53>;
+ pagesize = <8>;
+ };
+};
+
+&cp0_mdio {
+ pinctrl-0 = <&cp0_mdio_pins>;
+ status = "okay";
+
+ /* assembly option */
+ cp0_eth2_phy: ethernet-phy@0 {
+ reg = <0>;
+ };
+};
+
+&cp0_spi1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_spi1_pins>;
+ /* max speed limited by a mux */
+ spi-max-frequency = <1800000000>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ /* read command supports max. 50MHz */
+ spi-max-frequency = <50000000>;
+ };
+};
+
+&cp0_syscon0 {
+ cp0_pinctrl: pinctrl {
+ compatible = "marvell,cp115-standalone-pinctrl";
+
+ cp0_eth2_pins: cp0-ge2-rgmii-pins {
+ marvell,pins = "mpp44", "mpp45", "mpp46", "mpp47",
+ "mpp48", "mpp49", "mpp50", "mpp51",
+ "mpp52", "mpp53", "mpp54", "mpp55";
+ /* docs call it "ge2", but cp110-pinctrl "ge1" */
+ marvell,function = "ge1";
+ };
+
+ cp0_i2c0_pins: cp0-i2c0-pins {
+ marvell,pins = "mpp37", "mpp38";
+ marvell,function = "i2c0";
+ };
+
+ cp0_mdio_pins: cp0-mdio-pins {
+ marvell,pins = "mpp40", "mpp41";
+ marvell,function = "ge";
+ };
+
+ cp0_spi1_pins: cp0-spi1-pins {
+ marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
+ marvell,function = "spi1";
+ };
+
+ cp0_reg_vhv_pins: cp0-reg-vhv-pins {
+ marvell,pins = "mpp41";
+ marvell,function = "gpio";
+ };
+ };
+};
+
+/* AP default console */
+&uart0 {
+ pinctrl-0 = <&uart0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};

--
2.35.3