From: Sergei Shtylyov <sergei.shtylyov-M4DtvfQ/ZS1MRgGoP+s0PdBPR1lH4CV8@public.gmane.org>
To: horms-/R6kz+dDXgpPR4JQBCEnsQ@public.gmane.org,
linux-renesas-soc-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
mark.rutland-5wv7dgnIgG8@public.gmane.org,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: magnus.damm-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org,
linux-lFZ/pmaqli7XmaaqVzeoHQ@public.gmane.org,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
Subject: [PATCH 3/3] ARM: dts: wheat: add Ethernet support
Date: Fri, 26 Aug 2016 23:23:13 +0300 [thread overview]
Message-ID: <6321460.7sCGaKUd5m@wasted.cogentembedded.com> (raw)
In-Reply-To: <3665116.9BjHTnhfR3-gHKXc3Y1Z8zGSmamagVegGFoWSdPRAKMAL8bYrjMMd8@public.gmane.org>
R8A7792 SoC doesn't have the EtherMAC core, so SMSC LAN89218 Ethernet
chip was used instead on the Wheat debug board; this chip is compatible
with SMSC LAN9115 for which there's a (device tree aware) driver.
Describe the chip in the Wheat device tree unconditionally (the driver
should fail the probe if the debug board isn't connected); enable DHCP and
NFS root in the command line for the kernel boot...
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov-M4DtvfQ/ZS1MRgGoP+s0PdBPR1lH4CV8@public.gmane.org>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov-M4DtvfQ/ZS1MRgGoP+s0PdBPR1lH4CV8@public.gmane.org>
---
arch/arm/boot/dts/r8a7792-wheat.dts | 38 +++++++++++++++++++++++++++++++++++-
1 file changed, 37 insertions(+), 1 deletion(-)
Index: renesas/arch/arm/boot/dts/r8a7792-wheat.dts
===================================================================
--- renesas.orig/arch/arm/boot/dts/r8a7792-wheat.dts
+++ renesas/arch/arm/boot/dts/r8a7792-wheat.dts
@@ -21,7 +21,7 @@
};
chosen {
- bootargs = "ignore_loglevel";
+ bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
stdout-path = "serial0:115200n8";
};
@@ -29,6 +29,31 @@
device_type = "memory";
reg = <0 0x40000000 0 0x40000000>;
};
+
+ d3_3v: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "D3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ethernet@18000000 {
+ compatible = "smsc,lan89218", "smsc,lan9115";
+ reg = <0 0x18000000 0 0x100>;
+ phy-mode = "mii";
+ interrupt-parent = <&irqc>;
+ interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+ smsc,irq-push-pull;
+ smsc,save-mac-address;
+ reg-io-width = <4>;
+ vddvario-supply = <&d3_3v>;
+ vdd33a-supply = <&d3_3v>;
+
+ pinctrl-0 = <&lan89218_pins>;
+ pinctrl-names = "default";
+ };
};
&extal_clk {
@@ -40,6 +65,17 @@
groups = "scif0_data";
function = "scif0";
};
+
+ lan89218_pins: lan89218 {
+ intc {
+ groups = "intc_irq0";
+ function = "intc";
+ };
+ lbsc {
+ groups = "lbsc_ex_cs0";
+ function = "lbsc";
+ };
+ };
};
&scif0 {
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2016-08-26 20:23 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-08-26 20:16 [PATCH 0/3] Add R8A7792/Wheat board support Sergei Shtylyov
2016-08-26 20:20 ` [PATCH 1/3] DT: arm: shmobile: document Wheat board Sergei Shtylyov
[not found] ` <81794087.EqU2I9TLcp-gHKXc3Y1Z8zGSmamagVegGFoWSdPRAKMAL8bYrjMMd8@public.gmane.org>
2016-08-29 7:57 ` Geert Uytterhoeven
2016-09-02 12:56 ` Rob Herring
[not found] ` <3665116.9BjHTnhfR3-gHKXc3Y1Z8zGSmamagVegGFoWSdPRAKMAL8bYrjMMd8@public.gmane.org>
2016-08-26 20:21 ` [PATCH 2/3] ARM: dts: wheat: initial device tree Sergei Shtylyov
2016-08-29 8:03 ` Geert Uytterhoeven
2016-08-26 20:23 ` Sergei Shtylyov [this message]
2016-08-29 8:05 ` [PATCH 3/3] ARM: dts: wheat: add Ethernet support Geert Uytterhoeven
2016-08-29 9:02 ` [PATCH 0/3] Add R8A7792/Wheat board support Simon Horman
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=6321460.7sCGaKUd5m@wasted.cogentembedded.com \
--to=sergei.shtylyov-m4dtvfq/zs1mrggop+s0pdbpr1lh4cv8@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=horms-/R6kz+dDXgpPR4JQBCEnsQ@public.gmane.org \
--cc=linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
--cc=linux-lFZ/pmaqli7XmaaqVzeoHQ@public.gmane.org \
--cc=linux-renesas-soc-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=magnus.damm-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org \
--cc=mark.rutland-5wv7dgnIgG8@public.gmane.org \
--cc=robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).