From: Pratyush Anand <panand@redhat.com>
To: dongbo4@huawei.com, bhelgaas@google.com, jingoohan1@gmail.com
Cc: linux-pci@vger.kernel.org,
Pratyush Anand <pratyush.anand@gmail.com>,
"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
<devicetree@vger.kernel.org>, Joao Pinto <jpinto@synopsys.com>,
open list <linux-kernel@vger.kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Rob Herring <robh+dt@kernel.org>
Subject: [PATCH 1/2] pcie/designware: Keep viewport fixed for IO transaction if num_viewport > 2
Date: Mon, 4 Jul 2016 21:44:42 +0530 [thread overview]
Message-ID: <687a0706f69f6ebea047441aba5231113fd0c898.1467647958.git.panand@redhat.com> (raw)
In-Reply-To: <cover.1467647958.git.panand@redhat.com>
In-Reply-To: <cover.1467647958.git.panand@redhat.com>
From: Pratyush Anand <pratyush.anand@gmail.com>
Most of the platform have 3 or more viewports. We do not need to share
viewport for such platform between IO and CFG. Assign viewport 2 to IO
transactions in such cases.
Signed-off-by: Pratyush Anand <pratyush.anand@gmail.com>
Tested-by: Dong Bo <dongbo4@huawei.com>
---
.../devicetree/bindings/pci/designware-pcie.txt | 3 +++
drivers/pci/host/pcie-designware.c | 26 ++++++++++++++++------
drivers/pci/host/pcie-designware.h | 1 +
3 files changed, 23 insertions(+), 7 deletions(-)
diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt
index 6c5322c55411..a72b7ecb80ee 100644
--- a/Documentation/devicetree/bindings/pci/designware-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt
@@ -17,6 +17,8 @@ Required properties:
- num-lanes: number of lanes to use
Optional properties:
+- num-viewport: number of view port configured in hardware. If a platform
+ does not specify it then driver will consider num-viewport as 2.
- num-lanes: number of lanes to use (this property should be specified unless
the link is brought already up in BIOS)
- reset-gpio: gpio pin number of power good signal
@@ -44,4 +46,5 @@ Example configuration:
interrupts = <25>, <24>;
#interrupt-cells = <1>;
num-lanes = <1>;
+ num-viewport = <3>;
};
diff --git a/drivers/pci/host/pcie-designware.c b/drivers/pci/host/pcie-designware.c
index aafd766546f3..4c17c02ad72b 100644
--- a/drivers/pci/host/pcie-designware.c
+++ b/drivers/pci/host/pcie-designware.c
@@ -51,6 +51,7 @@
#define PCIE_ATU_VIEWPORT 0x900
#define PCIE_ATU_REGION_INBOUND (0x1 << 31)
#define PCIE_ATU_REGION_OUTBOUND (0x0 << 31)
+#define PCIE_ATU_REGION_INDEX2 (0x2 << 0)
#define PCIE_ATU_REGION_INDEX1 (0x1 << 0)
#define PCIE_ATU_REGION_INDEX0 (0x0 << 0)
#define PCIE_ATU_CR1 0x904
@@ -521,6 +522,10 @@ int dw_pcie_host_init(struct pcie_port *pp)
if (ret)
pp->lanes = 0;
+ ret = of_property_read_u32(np, "num-viewport", &pp->num_viewport);
+ if (ret)
+ pp->num_viewport = 2;
+
if (IS_ENABLED(CONFIG_PCI_MSI)) {
if (!pp->ops->msi_host_init) {
pp->irq_domain = irq_domain_add_linear(pp->dev->of_node,
@@ -603,9 +608,10 @@ static int dw_pcie_rd_other_conf(struct pcie_port *pp, struct pci_bus *bus,
type, cpu_addr,
busdev, cfg_size);
ret = dw_pcie_cfg_read(va_cfg_base + where, size, val);
- dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX0,
- PCIE_ATU_TYPE_IO, pp->io_base,
- pp->io_bus_addr, pp->io_size);
+ if (pp->num_viewport <= 2)
+ dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX0,
+ PCIE_ATU_TYPE_IO, pp->io_base,
+ pp->io_bus_addr, pp->io_size);
return ret;
}
@@ -640,9 +646,10 @@ static int dw_pcie_wr_other_conf(struct pcie_port *pp, struct pci_bus *bus,
type, cpu_addr,
busdev, cfg_size);
ret = dw_pcie_cfg_write(va_cfg_base + where, size, val);
- dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX0,
- PCIE_ATU_TYPE_IO, pp->io_base,
- pp->io_bus_addr, pp->io_size);
+ if (pp->num_viewport <= 2)
+ dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX0,
+ PCIE_ATU_TYPE_IO, pp->io_base,
+ pp->io_bus_addr, pp->io_size);
return ret;
}
@@ -778,10 +785,15 @@ void dw_pcie_setup_rc(struct pcie_port *pp)
* uses its own address translation component rather than ATU, so
* we should not program the ATU here.
*/
- if (!pp->ops->rd_other_conf)
+ if (!pp->ops->rd_other_conf) {
dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX1,
PCIE_ATU_TYPE_MEM, pp->mem_base,
pp->mem_bus_addr, pp->mem_size);
+ if (pp->num_viewport > 2)
+ dw_pcie_prog_outbound_atu(pp, PCIE_ATU_REGION_INDEX2,
+ PCIE_ATU_TYPE_IO, pp->io_base,
+ pp->io_bus_addr, pp->io_size);
+ }
dw_pcie_wr_own_conf(pp, PCI_BASE_ADDRESS_0, 4, 0);
diff --git a/drivers/pci/host/pcie-designware.h b/drivers/pci/host/pcie-designware.h
index f437f9b5be04..61f479dd181d 100644
--- a/drivers/pci/host/pcie-designware.h
+++ b/drivers/pci/host/pcie-designware.h
@@ -49,6 +49,7 @@ struct pcie_port {
struct resource *busn;
int irq;
u32 lanes;
+ u32 num_viewport;
struct pcie_host_ops *ops;
int msi_irq;
struct irq_domain *irq_domain;
--
2.5.5
next parent reply other threads:[~2016-07-04 16:14 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <cover.1467647958.git.panand@redhat.com>
2016-07-04 16:14 ` Pratyush Anand [this message]
2016-07-05 16:23 ` [PATCH 1/2] pcie/designware: Keep viewport fixed for IO transaction if num_viewport > 2 Rob Herring
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=687a0706f69f6ebea047441aba5231113fd0c898.1467647958.git.panand@redhat.com \
--to=panand@redhat.com \
--cc=bhelgaas@google.com \
--cc=devicetree@vger.kernel.org \
--cc=dongbo4@huawei.com \
--cc=jingoohan1@gmail.com \
--cc=jpinto@synopsys.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=pratyush.anand@gmail.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox