[PATCH v4 1/1] ARM: dts: aspeed: Add device tree for Nvidia's GB200 UT3.0b platform BMC

[PATCH v4 1/1] ARM: dts: aspeed: Add device tree for Nvidia's GB200 UT3.0b platform BMC

[Donald Shannon]

The GB200NVL UT3.0b BMC is an Aspeed Ast2600 based BMC
for Nvidia Blackwell GB200NVL platform.
Reference to Ast2600 SOC [1].
Reference to Blackwell GB200NVL Platform [2].

Link: https://www.aspeedtech.com/server_ast2600/ [1]
Link: https://nvdam.widen.net/s/wwnsxrhm2w/blackwell-datasheet-3384703 [2]

Signed-off-by: Donald Shannon <donalds@nvidia.com>
---
Changes v1 -> v2:
  - Changed phy-mode to rgmii-id [Lunn]
  - Removed redundant max-speed for mac0 [Lunn]
  - Fixed typo from gb200nvl to gb200 in Makefile
Changes v2 -> v3:
  - Fixed whitespace issues [Krzysztof]
  - Fixed schema validation issues from my end ( there are still issues with the aspeed dtsi file that are not related to this new dts) [Herring]
  - Reordered to follow style guide [Krzysztof]
  - Removed redundant status okays
  - Changed vcc to vdd for the power gating on the gpio expanders
Changes v3 -> v4:
  - Added changelog [Krzysztof]
  - Added nvidia,gb200-ut30b board binding [Krzysztof]
  - Removed unused imports
  - Reordered a couple other style guide violations
  - Added back in a couple needed "status okay"s
---

Donald Shannon (1):
  ARM: dts: aspeed: Add device tree for Nvidia's GB200 UT3.0b platform
    BMC

 .../bindings/arm/aspeed/aspeed.yaml           |    1 +
 arch/arm/boot/dts/aspeed/Makefile             |    1 +
 .../aspeed/aspeed-bmc-nvidia-gb200-ut30b.dts  | 1154 +++++++++++++++++
 3 files changed, 1156 insertions(+)
 create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dts


base-commit: 460178e842c7a1e48a06df684c66eb5fd630bcf7
-- 
2.43.0

[PATCH v4 1/1] ARM: dts: aspeed: Add device tree for Nvidia's GB200 UT3.0b platform BMC

[Donald Shannon]

The GB200NVL UT3.0b BMC is an Aspeed Ast2600 based BMC
for Nvidia Blackwell GB200NVL platform.
Reference to Ast2600 SOC [1].
Reference to Blackwell GB200NVL Platform [2].

Link: https://www.aspeedtech.com/server_ast2600/ [1]
Link: https://nvdam.widen.net/s/wwnsxrhm2w/blackwell-datasheet-3384703 [2]

Signed-off-by: Donald Shannon <donalds@nvidia.com>
---
Changes v1 -> v2:
  - Changed phy-mode to rgmii-id [Lunn]
  - Removed redundant max-speed for mac0 [Lunn]
  - Fixed typo from gb200nvl to gb200 in Makefile
Changes v2 -> v3:
  - Fixed whitespace issues [Krzysztof]
  - Fixed schema validation issues from my end ( there are still issues with the aspeed dtsi file that are not related to this new dts) [Herring]
  - Reordered to follow style guide [Krzysztof]
  - Removed redundant status okays
  - Changed vcc to vdd for the power gating on the gpio expanders
Changes v3 -> v4:
  - Added changelog [Krzysztof]
  - Added nvidia,gb200-ut30b board binding [Krzysztof]
  - Removed unused imports
  - Reordered a couple other style guide violations
  - Added back in a couple needed "status okay"s
---
 .../bindings/arm/aspeed/aspeed.yaml           |    1 +
 arch/arm/boot/dts/aspeed/Makefile             |    1 +
 .../aspeed/aspeed-bmc-nvidia-gb200-ut30b.dts  | 1154 +++++++++++++++++
 3 files changed, 1156 insertions(+)
 create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dts

diff --git a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
index a3736f134130..420fabf05b24 100644
--- a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
+++ b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
@@ -98,6 +98,7 @@ properties:
               - inventec,starscream-bmc
               - inventec,transformer-bmc
               - jabil,rbp-bmc
+              - nvidia,gb200-ut30b
               - nvidia,gb200nvl-bmc
               - qcom,dc-scm-v1-bmc
               - quanta,s6q-bmc
diff --git a/arch/arm/boot/dts/aspeed/Makefile b/arch/arm/boot/dts/aspeed/Makefile
index b3170fdd3096..1101bc74e8c8 100644
--- a/arch/arm/boot/dts/aspeed/Makefile
+++ b/arch/arm/boot/dts/aspeed/Makefile
@@ -51,6 +51,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-bmc-lenovo-hr855xg2.dtb \
 	aspeed-bmc-microsoft-olympus.dtb \
 	aspeed-bmc-nvidia-gb200nvl-bmc.dtb \
+	aspeed-bmc-nvidia-gb200-ut30b.dtb \
 	aspeed-bmc-opp-lanyang.dtb \
 	aspeed-bmc-opp-mowgli.dtb \
 	aspeed-bmc-opp-nicole.dtb \
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dts
new file mode 100644
index 000000000000..5104569058cc
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dts
@@ -0,0 +1,1154 @@
+// SPDX-License-Identifier: GPL-2.0+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+	model = "AST2600 GB200 UT3.0b BMC";
+	compatible = "nvidia,gb200-ut30b", "aspeed,ast2600";
+
+	aliases {
+		serial2 = &uart3;
+		serial4 = &uart5;
+		i2c16   = &imux16;
+		i2c17   = &imux17;
+		i2c18   = &imux18;
+		i2c19   = &imux19;
+		i2c20   = &imux20;
+		i2c21   = &imux21;
+		i2c22   = &imux22;
+		i2c23   = &imux23;
+		i2c24   = &imux24;
+		i2c25   = &imux25;
+		i2c26   = &imux26;
+		i2c27   = &imux27;
+		i2c28   = &imux28;
+		i2c29   = &imux29;
+		i2c30   = &imux30;
+		i2c31   = &imux31;
+		i2c32   = &imux32;
+		i2c33   = &imux33;
+		i2c34   = &imux34;
+		i2c35   = &imux35;
+		i2c36   = &imux36;
+		i2c37   = &imux37;
+		i2c38   = &imux38;
+		i2c39   = &imux39;
+		i2c40	= &e1si2c0;
+		i2c41	= &e1si2c1;
+		i2c42	= &e1si2c2;
+		i2c43	= &e1si2c3;
+		i2c44	= &e1si2c4;
+		i2c45	= &e1si2c5;
+		i2c46	= &e1si2c6;
+		i2c47	= &e1si2c7;
+		i2c48	= &i2c17mux0;
+		i2c49	= &i2c17mux1;
+		i2c50	= &i2c17mux2;
+		i2c51	= &i2c17mux3;
+		i2c52	= &i2c25mux0;
+		i2c53	= &i2c25mux1;
+		i2c54	= &i2c25mux2;
+		i2c55	= &i2c25mux3;
+		i2c56	= &i2c29mux0;
+		i2c57	= &i2c29mux1;
+		i2c58	= &i2c29mux2;
+		i2c59	= &i2c29mux3;
+	};
+
+	buttons {
+		button-power {
+			label = "power-btn";
+			gpio = <&sgpiom0 156 GPIO_ACTIVE_LOW>;
+		};
+		button-uid {
+			label = "uid-btn";
+			gpio = <&sgpiom0 154 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	chosen {
+		stdout-path = &uart5;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-0 {
+			label = "uid_led";
+			gpios = <&sgpiom0 27 GPIO_ACTIVE_LOW>;
+		};
+		led-1 {
+			label = "fault_led";
+			gpios = <&sgpiom0 29 GPIO_ACTIVE_LOW>;
+		};
+		led-2 {
+			label = "power_led";
+			gpios = <&sgpiom0 31 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	reg_3v3_stby: regulator-3v3-standby {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3-standby";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio0 ASPEED_GPIO(M, 3) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		vga_memory: framebuffer@9f000000 {
+			no-map;
+			reg = <0x9f000000 0x01000000>; /* 16M */
+		};
+
+		ramoops@a0000000 {
+			compatible = "ramoops";
+			reg = <0xa0000000 0x100000>; /* 1MB */
+			record-size = <0x10000>; /* 64KB */
+			max-reason = <2>; /* KMSG_DUMP_OOPS */
+		};
+
+		gfx_memory: framebuffer {
+			compatible = "shared-dma-pool";
+			reusable;
+			size = <0x01000000>;
+			alignment = <0x01000000>;
+		};
+
+		video_engine_memory: jpegbuffer {
+			compatible = "shared-dma-pool";
+			reusable;
+			size = <0x02000000>;	/* 32M */
+			alignment = <0x01000000>;
+		};
+	};
+};
+
+// Enable Primary flash on FMC for bring up activity
+&fmc {
+	status = "okay";
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+		status = "okay";
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			u-boot@0 {
+				// 896KB
+				reg = <0x0 0xe0000>;
+				label = "u-boot";
+			};
+
+			kernel@100000 {
+				// 9MB
+				reg = <0x100000 0x900000>;
+				label = "kernel";
+			};
+
+			rofs@a00000 {
+				// 55292KB (extends to end of 64MB SPI - 4KB)
+				reg = <0xa00000 0x35FF000>;
+				label = "rofs";
+			};
+		};
+	};
+};
+
+&spi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi2_default>;
+	status = "okay";
+	// Data SPI is 64MB in size
+	flash@0 {
+		label = "config";
+		spi-max-frequency = <50000000>;
+		status = "okay";
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			u-boot-env@0 {
+				// 256KB
+				reg = <0x0 0x40000>;
+				label = "u-boot-env";
+			};
+
+			rwfs@40000 {
+				// 16MB
+				reg = <0x40000 0x1000000>;
+				label = "rwfs";
+			};
+
+			log@1040000 {
+				// 40MB
+				reg = <0x1040000 0x2800000>;
+				label = "log";
+			};
+		};
+	};
+};
+
+&mdio0 {
+	status = "okay";
+	ethphy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mac0 {
+	pinctrl-names = "default";
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	pinctrl-0 = <&pinctrl_rgmii1_default>;
+	status = "okay";
+};
+
+// USB 2.0 to HMC, on USB Port B
+&ehci1 {
+	status = "okay";
+};
+
+// USB 1.0
+&uhci {
+	status = "okay";
+};
+
+/*
+ * Enable USB port A as device (via the virtual hub) to host
+ */
+&vhub {
+	status = "okay";
+};
+
+&rng {
+	status = "okay";
+};
+
+&video {
+	memory-region = <&video_engine_memory>;
+	status = "okay";
+};
+
+&gpio0 {
+	gpio-line-names =
+		/*A0-A7*/ "", "", "", "", "", "", "", "",
+		/*B0-B7*/ "", "", "", "", "", "", "", "",
+		/*C0-C7*/ "SGPIO_I2C_MUX_SEL-O", "", "", "", "", "", "", "",
+		/*D0-D7*/ "", "", "", "UART1_MUX_SEL-O", "", "FPGA_PEX_RST_L-O", "", "",
+		/*E0-E7*/ "RTL8221_PHY_RST_L-O", "RTL8211_PHY_INT_L-I",	"", "UART3_MUX_SEL-O",
+					"", "", "", "SGPIO_BMC_EN-O",
+		/*F0-F7*/ "", "", "", "", "", "", "", "",
+		/*G0-G7*/ "", "", "", "", "", "", "", "",
+		/*H0-H7*/ "", "", "", "", "", "", "", "",
+		/*I0-I7*/ "", "", "", "", "", "QSPI2_RST_L-O", "GLOBAL_WP_BMC-O", "BMC_DDR4_TEN-O",
+		/*J0-J7*/ "", "", "", "", "", "", "", "",
+		/*K0-K7*/ "", "", "", "", "", "", "", "",
+		/*L0-L7*/ "", "", "", "", "", "", "", "",
+		/*M0-M7*/ "PCIE_EP_RST_EN-O", "BMC_FRU_WP-O", "FPGA_RST_L-O", "STBY_POWER_EN-O",
+					"STBY_POWER_PG-I", "PCIE_EP_RST_L-O", "", "",
+		/*N0-N7*/ "", "", "", "", "", "", "", "",
+		/*O0-O7*/ "", "", "", "", "", "", "", "",
+		/*P0-P7*/ "", "", "", "", "", "", "", "",
+		/*Q0-Q7*/ "", "", "", "", "", "", "", "",
+		/*R0-R7*/ "", "", "", "", "", "", "", "",
+		/*S0-S7*/ "", "", "", "", "", "", "", "",
+		/*T0-T7*/ "", "", "", "", "", "", "", "",
+		/*U0-U7*/ "", "", "", "", "", "", "", "",
+		/*V0-V7*/ "AP_EROT_REQ-O", "EROT_AP_GNT-I", "", "","PCB_TEMP_ALERT-I", "","", "",
+		/*W0-W7*/ "", "", "", "", "", "", "", "",
+		/*X0-X7*/ "", "", "TPM_MUX_SEL-O", "", "", "", "", "",
+		/*Y0-Y7*/ "", "", "", "EMMC_RST-O", "","", "", "",
+		/*Z0-Z7*/ "BMC_READY-O","", "", "", "", "", "", "";
+};
+
+&gpio1 {
+	/* 36 1.8V GPIOs */
+	gpio-line-names =
+		/*A0-A7*/ "", "", "", "", "", "", "", "",
+		/*B0-B7*/ "", "", "", "", "", "", "IO_EXPANDER_INT_L-I","",
+		/*C0-C7*/ "", "", "", "", "", "", "", "",
+		/*D0-D7*/ "", "", "", "", "", "", "SPI_HOST_TPM_RST_L-O", "SPI_BMC_FPGA_INT_L-I",
+		/*E0-E7*/ "", "", "", "", "", "", "", "";
+};
+
+&sgpiom0 {
+	ngpios = <128>;
+	status = "okay";
+	gpio-line-names =
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"RUN_POWER_FAULT_L-I","SYS_RST_IN_L-O",
+		"RUN_POWER_PG-I","PWR_BRAKE_L-O",
+		"SYS_RST_OUT_L-I","RUN_POWER_EN-O",
+		"L0L1_RST_REQ_OUT_L-I","SHDN_FORCE_L-O",
+		"L2_RST_REQ_OUT_L-I","SHDN_REQ_L-O",
+		"SHDN_OK_L-I","UID_LED_N-O",
+		"BMC_I2C1_FPGA_ALERT_L-I","SYS_FAULT_LED_N-O",
+		"BMC_I2C0_FPGA_ALERT_L-I","PWR_LED_N-O",
+		"FPGA_RSVD_FFU3-I","",
+		"FPGA_RSVD_FFU2-I","",
+		"FPGA_RSVD_FFU1-I","",
+		"FPGA_RSVD_FFU0-I","BMC_I2C_SSIF_ALERT_L-O",
+		"CPU_BOOT_DONE-I","JTAG_MUX_SELECT-O",
+		"SPI_BMC_FPGA_INT_L-I","RTC_CLR_L-O",
+		"THERM_BB_WARN_L-I","UART_MUX_SEL-O",
+		"THERM_BB_OVERT_L-I","",
+		"CPU0_UPHY3_PRSNT1_L-I","IOBRD0_RUN_POWER_EN-O",
+		"CPU0_UPHY3_PRSNT0_L-I","IOBRD1_RUN_POWER_EN-O",
+		"CPU0_UPHY2_PRSNT1_L-I","FPGA_RSVD_FFU4-O",
+		"CPU0_UPHY2_PRSNT0_L-I","FPGA_RSVD_FFU5-O",
+		"CPU0_UPHY1_PRSNT1_L-I","FPGA_RSVD_FFU6-O",
+		"CPU0_UPHY1_PRSNT0_L-I","FPGA_RSVD_FFU7-O",
+		"CPU0_UPHY0_PRSNT1_L-I","RSVD_NV_PLT_DETECT-O",
+		"CPU0_UPHY0_PRSNT0_L-I","SPI1_INT_L-O",
+		"CPU1_UPHY3_PRSNT1_L-I","",
+		"CPU1_UPHY3_PRSNT0_L-I","HMC_EROT_MUX_STATUS",
+		"CPU1_UPHY2_PRSNT1_L-I","",
+		"CPU1_UPHY2_PRSNT0_L-I","",
+		"CPU1_UPHY1_PRSNT1_L-I","",
+		"CPU1_UPHY1_PRSNT0_L-I","",
+		"CPU1_UPHY0_PRSNT1_L-I","",
+		"CPU1_UPHY0_PRSNT0_L-I","",
+		"FAN1_PRESENT_L-I","",
+		"FAN0_PRESENT_L-I","",
+		"","",
+		"IPEX_CABLE_PRSNT_L-I","",
+		"M2_1_PRSNT_L-I","",
+		"M2_0_PRSNT_L-I","",
+		"CPU1_UPHY4_PRSNT1_L-I","",
+		"CPU0_UPHY4_PRSNT0_L-I","",
+		"","",
+		"I2C_RTC_ALERT_L-I","",
+		"FAN7_PRESENT_L-I","",
+		"FAN6_PRESENT_L-I","",
+		"FAN5_PRESENT_L-I","",
+		"FAN4_PRESENT_L-I","",
+		"FAN3_PRESENT_L-I","",
+		"FAN2_PRESENT_L-I","",
+		"IOBRD0_IOX_INT_L-I","",
+		"IOBRD1_PRSNT_L-I","",
+		"IOBRD0_PRSNT_L-I","",
+		"IOBRD1_PWR_GOOD-I","",
+		"IOBRD0_PWR_GOOD-I","",
+		"","",
+		"","",
+		"FAN_FAIL_IN_L-I","",
+		"","",
+		"","",
+		"","",
+		"PDB_CABLE_PRESENT_L-I","",
+		"","",
+		"CHASSIS_PWR_BRK_L-I","",
+		"","",
+		"IOBRD1_IOX_INT_L-I","",
+		"10GBE_SMBALRT_L-I","",
+		"PCIE_WAKE_L-I","",
+		"I2C_M21_ALERT_L-I","",
+		"I2C_M20_ALERT_L-I","",
+		"TRAY_FAST_SHDN_L-I","",
+		"UID_BTN_N-I","",
+		"PWR_BTN_L-I","",
+		"PSU_SMB_ALERT_L-I","",
+		"","",
+		"","",
+		"NODE_LOC_ID[0]-I","",
+		"NODE_LOC_ID[1]-I","",
+		"NODE_LOC_ID[2]-I","",
+		"NODE_LOC_ID[3]-I","",
+		"NODE_LOC_ID[4]-I","",
+		"NODE_LOC_ID[5]-I","",
+		"FAN10_PRESENT_L-I","",
+		"FAN9_PRESENT_L-I","",
+		"FAN8_PRESENT_L-I","",
+		"FPGA1_READY_HMC-I","",
+		"DP_HPD-I","",
+		"HMC_I2C3_FPGA_ALERT_L-I","",
+		"HMC_I2C2_FPGA_ALERT_L-I","",
+		"FPGA0_READY_HMC-I","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"LEAK_DETECT_ALERT_L-I","",
+		"MOD1_B2B_CABLE_PRESENT_L-I","",
+		"MOD1_CLINK_CABLE_PRESENT_L-I","",
+		"FAN11_PRESENT_L-I","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"RSVD_SGPIO_IN_CRC[0]","RSVD_SGPIO_O_CRC[7]",
+		"RSVD_SGPIO_IN_CRC[1]","RSVD_SGPIO_O_CRC[6]",
+		"RSVD_SGPIO_IN_CRC[2]","RSVD_SGPIO_O_CRC[5]",
+		"RSVD_SGPIO_IN_CRC[3]","RSVD_SGPIO_O_CRC[4]",
+		"RSVD_SGPIO_IN_CRC[4]","RSVD_SGPIO_O_CRC[3]",
+		"RSVD_SGPIO_IN_CRC[5]","RSVD_SGPIO_O_CRC[2]",
+		"RSVD_SGPIO_IN_CRC[6]","RSVD_SGPIO_O_CRC[1]",
+		"RSVD_SGPIO_IN_CRC[7]","RSVD_SGPIO_O_CRC[0]";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+// Enabling SOL
+&uart3 {
+	status = "okay";
+};
+
+// BMC Debug Console
+&uart5 {
+	status = "okay";
+};
+
+&uart_routing { };
+
+// I2C1, SSIF IPMI interface
+&i2c0 {
+	clock-frequency = <400000>;
+	status = "okay";
+	ssif-bmc@10 {
+		compatible = "ssif-bmc";
+		reg = <0x10>;
+	};
+};
+
+// I2C2
+// BMC_I2C1_FPGA - Secondary FPGA
+// HMC EROT
+&i2c1 {
+	clock-frequency = <400000>;
+	multi-master;
+	status = "okay";
+};
+
+// I2C3
+// BMC_I2C0_FPGA - Primary FPGA
+// HMC FRU EEPROM
+&i2c2 {
+	clock-frequency = <400000>;
+	multi-master;
+	status = "okay";
+};
+
+// I2C4
+&i2c3 {
+	clock-frequency = <400000>;
+	multi-master;
+	status = "okay";
+};
+
+// I2C5
+// RTC Driver
+// IO Expander
+&i2c4 {
+	clock-frequency = <400000>;
+	status = "okay";
+	// Module 0, Expander @0x21
+	exp4: gpio@21 {
+		compatible = "nxp,pca9555";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
+		vcc-supply = <&reg_3v3_stby>;
+		gpio-line-names =
+			"RTC_MUX_SEL-O",
+			"PCI_MUX_SEL-O",
+			"TPM_MUX_SEL-O",
+			"FAN_MUX-SEL-O",
+			"SGMII_MUX_SEL-O",
+			"DP_MUX_SEL-O",
+			"UPHY3_USB_SEL-O",
+			"NCSI_MUX_SEL-O",
+			"BMC_PHY_RST-O",
+			"RTC_CLR_L-O",
+			"BMC_12V_CTRL-O",
+			"PS_RUN_IO0_PG-I",
+			"",
+			"",
+			"",
+			"";
+	};
+};
+
+// I2C6
+// Module 0/1 I2C MUX x3
+&i2c5 {
+	clock-frequency = <400000>;
+	multi-master;
+	status = "okay";
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9546";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+		vdd-supply = <&reg_3v3_stby>;
+
+		imux16: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux17: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			i2c-mux@74 {
+				compatible = "nxp,pca9546";
+				reg = <0x74>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				i2c-mux-idle-disconnect;
+				vdd-supply = <&reg_3v3_stby>;
+
+				i2c17mux0: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				i2c17mux1: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				i2c17mux2: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				i2c17mux3: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+			};
+		};
+
+		imux18: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux19: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+
+	i2c-mux@72 {
+		compatible = "nxp,pca9546";
+		reg = <0x72>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+		vdd-supply = <&reg_3v3_stby>;
+
+		imux20: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		imux21: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			gpio@20 {
+				compatible = "nxp,pca9555";
+				reg = <0x20>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				vcc-supply = <&reg_3v3_stby>;
+				gpio-line-names =
+					"RST_CX_0_L-O",
+					"RST_CX_1_L-O",
+					"CX0_SSD0_PRSNT_L-I",
+					"CX1_SSD1_PRSNT_L-I",
+					"CX_BOOT_CMPLT_CX0-I",
+					"CX_BOOT_CMPLT_CX1-I",
+					"CX_TWARN_CX0_L-I",
+					"CX_TWARN_CX1_L-I",
+					"CX_OVT_SHDN_CX0-I",
+					"CX_OVT_SHDN_CX1-I",
+					"FNP_L_CX0-O",
+					"FNP_L_CX1-O",
+					"",
+					"MCU_GPIO-I",
+					"MCU_RST_N-O",
+					"MCU_RECOVERY_N-O";
+			};
+		};
+
+		imux22: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		imux23: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	i2c-mux@73 {
+		compatible = "nxp,pca9546";
+		reg = <0x73>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+		vdd-supply = <&reg_3v3_stby>;
+
+		imux24: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		imux25: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			i2c-mux@70 {
+				compatible = "nxp,pca9546";
+				reg = <0x70>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				i2c-mux-idle-disconnect;
+				vdd-supply = <&reg_3v3_stby>;
+
+				i2c25mux0: i2c@0 {
+					reg = <0>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+
+				i2c25mux1: i2c@1 {
+					reg = <1>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+
+				i2c25mux2: i2c@2 {
+					reg = <2>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+
+				i2c25mux3: i2c@3 {
+					reg = <3>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+			};
+		};
+
+		imux26: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		imux27: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	i2c-mux@75 {
+		compatible = "nxp,pca9546";
+		reg = <0x75>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+		vdd-supply = <&reg_3v3_stby>;
+
+		imux28: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		imux29: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			i2c-mux@74 {
+				compatible = "nxp,pca9546";
+				reg = <0x74>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				i2c-mux-idle-disconnect;
+				vdd-supply = <&reg_3v3_stby>;
+
+				i2c29mux0: i2c@0 {
+					reg = <0>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+
+				i2c29mux1: i2c@1 {
+					reg = <1>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+
+				i2c29mux2: i2c@2 {
+					reg = <2>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+
+				i2c29mux3: i2c@3 {
+					reg = <3>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+			};
+		};
+
+		imux30: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		imux31: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	i2c-mux@76 {
+		compatible = "nxp,pca9546";
+		reg = <0x76>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+		vdd-supply = <&reg_3v3_stby>;
+
+		imux32: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		imux33: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			gpio@21 {
+				compatible = "nxp,pca9555";
+				reg = <0x21>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				vcc-supply = <&reg_3v3_stby>;
+				gpio-line-names =
+					"SEC_RST_CX_0_L-O",
+					"SEC_RST_CX_1_L-O",
+					"SEC_CX0_SSD0_PRSNT_L-I",
+					"SEC_CX1_SSD1_PRSNT_L-I",
+					"SEC_CX_BOOT_CMPLT_CX0-I",
+					"SEC_CX_BOOT_CMPLT_CX1-I",
+					"SEC_CX_TWARN_CX0_L-I",
+					"SEC_CX_TWARN_CX1_L-I",
+					"SEC_CX_OVT_SHDN_CX0-I",
+					"SEC_CX_OVT_SHDN_CX1-I",
+					"SEC_FNP_L_CX0-O",
+					"SEC_FNP_L_CX1-O",
+					"",
+					"SEC_MCU_GPIO-I",
+					"SEC_MCU_RST_N-O",
+					"SEC_MCU_RECOVERY_N-O";
+				};
+		};
+
+		imux34: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		imux35: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	i2c-mux@77 {
+		compatible = "nxp,pca9546";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+		vdd-supply = <&reg_3v3_stby>;
+
+		imux36: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		imux37: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		imux38: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		imux39: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+// I2C7
+// Module 0/1 Leak Sensors
+// Module 0/1 Fan Controllers
+&i2c6 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	pmic@12 {
+		compatible = "ti,lm5066i";
+		reg = <0x12>;
+		shunt-resistor-micro-ohms = <190>;
+	};
+
+	pmic@14 {
+		compatible = "ti,lm5066i";
+		reg = <0x14>;
+		shunt-resistor-micro-ohms = <190>;
+	};
+
+	pwm@20 {
+		compatible = "maxim,max31790";
+		reg = <0x20>;
+	};
+
+	pwm@23 {
+		compatible = "maxim,max31790";
+		reg = <0x23>;
+	};
+
+	pwm@2c {
+		compatible = "maxim,max31790";
+		reg = <0x2c>;
+	};
+
+	pwm@2f {
+		compatible = "maxim,max31790";
+		reg = <0x2f>;
+	};
+};
+
+// I2C9
+// M.2
+&i2c8 {
+	clock-frequency = <400000>;
+	multi-master;
+	status = "okay";
+};
+
+// I2C10
+// Module 0/1 IO Expanders
+&i2c9 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	// Module 0, Expander @0x20
+	exp0: gpio@20 {
+		compatible = "nxp,pca9555";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
+		vcc-supply = <&reg_3v3_stby>;
+		gpio-line-names =
+			"FPGA_THERM_OVERT_L-I",
+			"FPGA_READY_BMC-I",
+			"HMC_BMC_DETECT-O",
+			"HMC_PGOOD-O",
+			"",
+			"BMC_STBY_CYCLE-O",
+			"FPGA_EROT_FATAL_ERROR_L-I",
+			"WP_HW_EXT_CTRL_L-O",
+			"EROT_FPGA_RST_L-O",
+			"FPGA_EROT_RECOVERY_L-O",
+			"BMC_EROT_FPGA_SPI_MUX_SEL-O",
+			"USB_HUB_RESET_L-O",
+			"NCSI_CS1_SEL-O",
+			"SGPIO_EN_L-O",
+			"B2B_IOEXP_INT_L-I",
+			"I2C_BUS_MUX_RESET_L-O";
+	};
+
+	// Module 1, Expander @0x21
+	exp1: gpio@21 {
+		compatible = "nxp,pca9555";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
+		vcc-supply = <&reg_3v3_stby>;
+		gpio-line-names =
+			"SEC_FPGA_THERM_OVERT_L-I",
+			"SEC_FPGA_READY_BMC-I",
+			"",
+			"",
+			"",
+			"",
+			"SEC_FPGA_EROT_FATAL_ERROR_L-I",
+			"SEC_WP_HW_EXT_CTRL_L-O",
+			"SEC_EROT_FPGA_RST_L-O",
+			"SEC_FPGA_EROT_RECOVERY_L-O",
+			"SEC_BMC_EROT_FPGA_SPI_MUX_SEL-O",
+			"SEC_USB2_HUB_RST_L-O",
+			"",
+			"",
+			"",
+			"SEC_I2C_BUS_MUX_RESET_L-O";
+	};
+
+	// UT3.0b Expander @0x22
+	exp2: gpio@22 {
+		compatible = "nxp,pca9555";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <14 IRQ_TYPE_LEVEL_LOW>;
+		gpio-line-names =
+			"BMC1_FANCTRL_FAIL_L-I",
+			"IOEXP_BMC_RST_12V-O",
+			"NODE_RST_STBY_H-O",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"";
+	};
+
+	// UT3.0b Expander @0x23
+	exp3: gpio@23 {
+		compatible = "nxp,pca9555";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <14 IRQ_TYPE_LEVEL_LOW>;
+		gpio-line-names =
+			"PEXSW_FL_SPI_MUX_SEL-O",
+			"PEX_SW_FATAL_ERROR_3V3_L-I",
+			"IOEXP_PDB_NODE_EN_L-O",
+			"NODE_PWOK_ISO-I",
+			"BMC_FAN_PWR_EN-O",
+			"BMC_ETHERNET_INT-I",
+			"BMC_ENET_RST-O",
+			"IOEXP_BMC_RST_SENSE-O",
+			"BMC_ID-I",
+			"TPM_MUX_3V3_SEL_N-O",
+			"IOEXP_TPM_RST_N-O",
+			"TPM_DOWN_SPI_INT_L-I",
+			"PS_BRD_PGOOD-I",
+			"FP_BUTTON_POWER_N-I",
+			"FP_BUTTON_RESET_N-I",
+			"FP_LED_POWER_GPIOEXP_N-O";
+	};
+};
+
+// I2C11
+// BMC FRU EEPROM
+// BMC Temp Sensor
+&i2c10 {
+	clock-frequency = <400000>;
+
+	// BMC FRU EEPROM - 256 bytes
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <8>;
+	};
+};
+
+// I2C12
+&i2c11 {
+	clock-frequency = <400000>;
+	status = "okay";
+};
+
+// I2C13
+&i2c12 {
+	status = "disabled";
+};
+
+// I2C14
+// Module 0 UPHY3 SMBus
+&i2c13 {
+	status = "disabled";
+};
+
+// I2C15
+// Module 1 UPHY3 SMBus
+&i2c14 {
+	clock-frequency = <100000>;
+	multi-master;
+	status = "okay";
+
+	//E1.S drive slot 0-3
+	i2c-mux@77 {
+		compatible = "nxp,pca9546";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+		vdd-supply = <&reg_3v3_stby>;
+
+		e1si2c0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		e1si2c1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		e1si2c2: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		e1si2c3: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+// I2C16
+&i2c15 {
+	clock-frequency = <100000>;
+	multi-master;
+	status = "okay";
+
+	//E1.S drive slot 4-7
+	i2c-mux@77 {
+		compatible = "nxp,pca9546";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+		vdd-supply = <&reg_3v3_stby>;
+
+		e1si2c4: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		e1si2c5: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		e1si2c6: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		e1si2c7: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
-- 
2.43.0

Re: [PATCH v4 1/1] ARM: dts: aspeed: Add device tree for Nvidia's GB200 UT3.0b platform BMC

[Rob Herring (Arm)]

On Tue, 10 Jun 2025 18:30:24 -0700, Donald Shannon wrote:
> The GB200NVL UT3.0b BMC is an Aspeed Ast2600 based BMC
> for Nvidia Blackwell GB200NVL platform.
> Reference to Ast2600 SOC [1].
> Reference to Blackwell GB200NVL Platform [2].
> 
> Link: https://www.aspeedtech.com/server_ast2600/ [1]
> Link: https://nvdam.widen.net/s/wwnsxrhm2w/blackwell-datasheet-3384703 [2]
> 
> Signed-off-by: Donald Shannon <donalds@nvidia.com>
> ---
> Changes v1 -> v2:
>   - Changed phy-mode to rgmii-id [Lunn]
>   - Removed redundant max-speed for mac0 [Lunn]
>   - Fixed typo from gb200nvl to gb200 in Makefile
> Changes v2 -> v3:
>   - Fixed whitespace issues [Krzysztof]
>   - Fixed schema validation issues from my end ( there are still issues with the aspeed dtsi file that are not related to this new dts) [Herring]
>   - Reordered to follow style guide [Krzysztof]
>   - Removed redundant status okays
>   - Changed vcc to vdd for the power gating on the gpio expanders
> Changes v3 -> v4:
>   - Added changelog [Krzysztof]
>   - Added nvidia,gb200-ut30b board binding [Krzysztof]
>   - Removed unused imports
>   - Reordered a couple other style guide violations
>   - Added back in a couple needed "status okay"s
> ---
> 
> Donald Shannon (1):
>   ARM: dts: aspeed: Add device tree for Nvidia's GB200 UT3.0b platform
>     BMC
> 
>  .../bindings/arm/aspeed/aspeed.yaml           |    1 +
>  arch/arm/boot/dts/aspeed/Makefile             |    1 +
>  .../aspeed/aspeed-bmc-nvidia-gb200-ut30b.dts  | 1154 +++++++++++++++++
>  3 files changed, 1156 insertions(+)
>  create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dts
> 
> 
> base-commit: 460178e842c7a1e48a06df684c66eb5fd630bcf7
> --
> 2.43.0
> 
> 
> 


My bot found new DTB warnings on the .dts files added or changed in this
series.

Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.

If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:

  pip3 install dtschema --upgrade


This patch series was applied (using b4) to base:
 Base: using specified base-commit 460178e842c7a1e48a06df684c66eb5fd630bcf7

If this is not the correct base, please add 'base-commit' tag
(or use b4 which does this automatically)

New warnings running 'make CHECK_DTBS=y for arch/arm/boot/dts/aspeed/' for 20250611013025.2898412-1-donalds@nvidia.com:

arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dtb: syscon@1e6e2000 (aspeed,ast2600-scu): 'smp-memram@180' does not match any of the regexes: '^interrupt-controller@[0-9a-f]+$', '^p2a-control@[0-9a-f]+$', '^pinctrl(@[0-9a-f]+)?$', '^pinctrl-[0-9]+$', '^silicon-id@[0-9a-f]+$'
	from schema $id: http://devicetree.org/schemas/mfd/aspeed,ast2x00-scu.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dtb: timer (arm,armv7-timer): 'clocks' does not match any of the regexes: '^pinctrl-[0-9]+$'
	from schema $id: http://devicetree.org/schemas/timer/arm,arch_timer.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dtb: /sdram@1e6e0000: failed to match any schema with compatible: ['aspeed,ast2600-sdram-edac', 'syscon']
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dtb: bus@1e600000 (aspeed,ast2600-ahbc): compatible: ['aspeed,ast2600-ahbc', 'syscon'] is too long
	from schema $id: http://devicetree.org/schemas/bus/aspeed,ast2600-ahbc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dtb: syscon@1e6e2000 (aspeed,ast2600-scu): 'smp-memram@180' does not match any of the regexes: '^interrupt-controller@[0-9a-f]+$', '^p2a-control@[0-9a-f]+$', '^pinctrl(@[0-9a-f]+)?$', '^pinctrl-[0-9]+$', '^silicon-id@[0-9a-f]+$'
	from schema $id: http://devicetree.org/schemas/mfd/aspeed,ast2x00-scu.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dtb: /ahb/apb@1e6e0000/syscon@1e6e2000/smp-memram@180: failed to match any schema with compatible: ['aspeed,ast2600-smpmem']
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dtb: /ahb/apb@1e6e0000/display@1e6e6000: failed to match any schema with compatible: ['aspeed,ast2600-gfx', 'syscon']
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dtb: adc@1e6e9000 (aspeed,ast2600-adc0): 'interrupts' does not match any of the regexes: '^pinctrl-[0-9]+$'
	from schema $id: http://devicetree.org/schemas/iio/adc/aspeed,ast2600-adc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dtb: adc@1e6e9100 (aspeed,ast2600-adc1): 'interrupts' does not match any of the regexes: '^pinctrl-[0-9]+$'
	from schema $id: http://devicetree.org/schemas/iio/adc/aspeed,ast2600-adc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dtb: crypto@1e6fa000 (aspeed,ast2600-acry): 'aspeed,ahbc' does not match any of the regexes: '^pinctrl-[0-9]+$'
	from schema $id: http://devicetree.org/schemas/crypto/aspeed,ast2600-acry.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dtb: sdc@1e740000 (aspeed,ast2600-sd-controller): sdhci@1e740100:compatible: ['aspeed,ast2600-sdhci', 'sdhci'] is too long
	from schema $id: http://devicetree.org/schemas/mmc/aspeed,sdhci.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dtb: sdc@1e740000 (aspeed,ast2600-sd-controller): sdhci@1e740200:compatible: ['aspeed,ast2600-sdhci', 'sdhci'] is too long
	from schema $id: http://devicetree.org/schemas/mmc/aspeed,sdhci.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dtb: /ahb/sdc@1e740000/sdhci@1e740100: failed to match any schema with compatible: ['aspeed,ast2600-sdhci', 'sdhci']
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dtb: /ahb/sdc@1e740000/sdhci@1e740200: failed to match any schema with compatible: ['aspeed,ast2600-sdhci', 'sdhci']
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dtb: /ahb/apb@1e780000/timer@1e782000: failed to match any schema with compatible: ['aspeed,ast2600-timer']
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dtb: lpc@1e789000 (aspeed,ast2600-lpc-v2): reg-io-width: 4 is not of type 'object'
	from schema $id: http://devicetree.org/schemas/mfd/aspeed-lpc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dtb: lpc@1e789000 (aspeed,ast2600-lpc-v2): lpc-snoop@80: 'clocks' does not match any of the regexes: '^pinctrl-[0-9]+$'
	from schema $id: http://devicetree.org/schemas/mfd/aspeed-lpc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dtb: kcs@24 (aspeed,ast2500-kcs-bmc-v2): 'clocks' does not match any of the regexes: '^pinctrl-[0-9]+$'
	from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dtb: kcs@28 (aspeed,ast2500-kcs-bmc-v2): 'clocks' does not match any of the regexes: '^pinctrl-[0-9]+$'
	from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dtb: kcs@2c (aspeed,ast2500-kcs-bmc-v2): 'clocks' does not match any of the regexes: '^pinctrl-[0-9]+$'
	from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dtb: kcs@114 (aspeed,ast2500-kcs-bmc-v2): 'clocks' does not match any of the regexes: '^pinctrl-[0-9]+$'
	from schema $id: http://devicetree.org/schemas/ipmi/aspeed,ast2400-kcs-bmc.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dtb: /ahb/apb@1e780000/lpc@1e789000/lhc@a0: failed to match any schema with compatible: ['aspeed,ast2600-lhc']
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dtb: /ahb/apb@1e780000/lpc@1e789000/ibt@140: failed to match any schema with compatible: ['aspeed,ast2600-ibt-bmc']
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dtb: fsi@1e79b000 (aspeed,ast2600-fsi-master): compatible: ['aspeed,ast2600-fsi-master', 'fsi-master'] is too long
	from schema $id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dtb: /ahb/apb@1e790000/fsi@1e79b000: failed to match any schema with compatible: ['aspeed,ast2600-fsi-master', 'fsi-master']
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dtb: fsi@1e79b100 (aspeed,ast2600-fsi-master): compatible: ['aspeed,ast2600-fsi-master', 'fsi-master'] is too long
	from schema $id: http://devicetree.org/schemas/fsi/aspeed,ast2600-fsi-master.yaml#
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dtb: /ahb/apb@1e790000/fsi@1e79b100: failed to match any schema with compatible: ['aspeed,ast2600-fsi-master', 'fsi-master']
arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dtb: /ahb/apb@1e790000/dma-controller@1e79e000: failed to match any schema with compatible: ['aspeed,ast2600-udma']

Re: [PATCH v4 1/1] ARM: dts: aspeed: Add device tree for Nvidia's GB200 UT3.0b platform BMC

[Krzysztof Kozlowski]

On 11/06/2025 03:30, Donald Shannon wrote:
> The GB200NVL UT3.0b BMC is an Aspeed Ast2600 based BMC
> for Nvidia Blackwell GB200NVL platform.
> Reference to Ast2600 SOC [1].
> Reference to Blackwell GB200NVL Platform [2].
> 
> Link: https://www.aspeedtech.com/server_ast2600/ [1]
> Link: https://nvdam.widen.net/s/wwnsxrhm2w/blackwell-datasheet-3384703 [2]
> 
> Signed-off-by: Donald Shannon <donalds@nvidia.com>
> ---
> Changes v1 -> v2:
>   - Changed phy-mode to rgmii-id [Lunn]
>   - Removed redundant max-speed for mac0 [Lunn]
>   - Fixed typo from gb200nvl to gb200 in Makefile
> Changes v2 -> v3:
>   - Fixed whitespace issues [Krzysztof]
>   - Fixed schema validation issues from my end ( there are still issues with the aspeed dtsi file that are not related to this new dts) [Herring]
>   - Reordered to follow style guide [Krzysztof]
>   - Removed redundant status okays
>   - Changed vcc to vdd for the power gating on the gpio expanders
> Changes v3 -> v4:
>   - Added changelog [Krzysztof]
>   - Added nvidia,gb200-ut30b board binding [Krzysztof]
>   - Removed unused imports
>   - Reordered a couple other style guide violations
>   - Added back in a couple needed "status okay"s
> ---
>  .../bindings/arm/aspeed/aspeed.yaml           |    1 +
>  arch/arm/boot/dts/aspeed/Makefile             |    1 +
>  .../aspeed/aspeed-bmc-nvidia-gb200-ut30b.dts  | 1154 +++++++++++++++++
>  3 files changed, 1156 insertions(+)
>  create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-ut30b.dts
> 
> diff --git a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
> index a3736f134130..420fabf05b24 100644
> --- a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
> +++ b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml


Please run scripts/checkpatch.pl on the patches and fix reported
warnings. After that, run also 'scripts/checkpatch.pl --strict' on the
patches and (probably) fix more warnings. Some warnings can be ignored,
especially from --strict run, but the code here looks like it needs a
fix. Feel free to get in touch if the warning is not clear.

You already got this comment, didn't you?

Best regards,
Krzysztof

Re: [PATCH v4 1/1] ARM: dts: aspeed: Add device tree for Nvidia's GB200 UT3.0b platform BMC

[Andrew Jeffery]

Hi Donald,

In addition to addressing Krzysztof's comments regarding checkpatch:

On Tue, 2025-06-10 at 18:30 -0700, Donald Shannon wrote:
> The GB200NVL UT3.0b BMC is an Aspeed Ast2600 based BMC
> for Nvidia Blackwell GB200NVL platform.

Can you add some words contrasting this platform to the one submitted
by Willie?

https://lore.kernel.org/all/20250401153955.314860-3-wthai@nvidia.com/


> Reference to Ast2600 SOC [1].
> Reference to Blackwell GB200NVL Platform [2].
> 
> Link: https://www.aspeedtech.com/server_ast2600/ [1]
> Link:
> https://nvdam.widen.net/s/wwnsxrhm2w/blackwell-datasheet-3384703 [2]
> 

Please omit the blank line here so the Link: tags are part of the
trailer.

> Signed-off-by: Donald Shannon <donalds@nvidia.com>
> ---
> Changes v1 -> v2:
>   - Changed phy-mode to rgmii-id [Lunn]
>   - Removed redundant max-speed for mac0 [Lunn]
>   - Fixed typo from gb200nvl to gb200 in Makefile
> Changes v2 -> v3:
>   - Fixed whitespace issues [Krzysztof]
>   - Fixed schema validation issues from my end ( there are still
> issues with the aspeed dtsi file that are not related to this new
> dts) [Herring]
>   - Reordered to follow style guide [Krzysztof]
>   - Removed redundant status okays
>   - Changed vcc to vdd for the power gating on the gpio expanders
> Changes v3 -> v4:
>   - Added changelog [Krzysztof]
>   - Added nvidia,gb200-ut30b board binding [Krzysztof]
>   - Removed unused imports
>   - Reordered a couple other style guide violations
>   - Added back in a couple needed "status okay"s
> ---
>  .../bindings/arm/aspeed/aspeed.yaml           |    1 +
>  arch/arm/boot/dts/aspeed/Makefile             |    1 +
>  .../aspeed/aspeed-bmc-nvidia-gb200-ut30b.dts  | 1154
> +++++++++++++++++
>  3 files changed, 1156 insertions(+)
>  create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200-
> ut30b.dts
> 
> diff --git a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
> b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
> index a3736f134130..420fabf05b24 100644
> --- a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
> +++ b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
> @@ -98,6 +98,7 @@ properties:
>                - inventec,starscream-bmc
>                - inventec,transformer-bmc
>                - jabil,rbp-bmc
> +              - nvidia,gb200-ut30b

For what it's worth, checkpatch reports at least the following:

   167: WARNING: DT binding docs and includes should be a separate patch. See: Documentation/devicetree/bindings/submitting-patches.rst
   180: WARNING: added, moved or deleted file(s), does MAINTAINERS need updating?
   193: WARNING: DT compatible string "nvidia,gb200-ut30b" appears un-documented -- check ./Documentation/devicetree/bindings/

Thanks,

Andrew

Re: [PATCH v4 1/1] ARM: dts: aspeed: Add device tree for Nvidia's GB200 UT3.0b platform BMC

[Andrew Jeffery]

On Thu, 2025-06-12 at 16:59 +0000, Donald Shannon wrote:
> Hi Andrew and Krzysztof,
> 
> The difference in this device tree is adding more GPIO expanders and
> changing the networking.

Can you please include a description of these differences in the commit
message?

> 
> Would it be best practice to create a new device binding (in this
> case nvidia,gb200-ut30b), even if it is just a slight modification on
> gb200nvl-bmc? Or can I reuse the gb200nvl-bmc compatible string and
> avoid the yaml binding change all together since it would share the
> same drivers?

You can include the aspeed-bmc-nvidia-gb200nvl-bmc.dts file and
override the nodes where the differences lie if that helps. There are
existing examples of this strategy, for instance:

   $ git grep '^#include .*\.dts"$' arch/arm/boot/dts/aspeed/
   arch/arm/boot/dts/aspeed/aspeed-ast2600-evb-a1.dts:#include "aspeed-ast2600-evb.dts"
   arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge-4u.dts:#include "aspeed-bmc-ibm-blueridge.dts"
   arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-rainier-1s4u.dts:#include "aspeed-bmc-ibm-rainier-4u.dts"
   arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-rainier-4u.dts:#include "aspeed-bmc-ibm-rainier.dts"

Whether or not the differences warrant a separate compatible - I'm not
sure.

Andrew