[PATCH 0/4] Add support for PECI Nuvoton

[PATCH 0/4] Add support for PECI Nuvoton

[Iwona Winiarska]

Hi!

The series adds support for PECI on Nuvoton-based BMC boards.
It is based on patches that were sent by Tomer Maimon from
Nuvoton [1].
Similar to Aspeed driver, unused (as in, default values were used in
all of the available DTS files) vendor-specific properties were
removed.
If there is a use-case for such properties, they can be added in
a separate series.

Thank you Tomer for testing this series on Nuvoton hardware [2].

Please note that PECI Nuvoton was previously submitted as part of PECI
subsystem series [3] that was never merged upstream.
It was never included in the current in-tree PECI subsystem [4].

[1] https://lore.kernel.org/openbmc/CAP6Zq1jnbQ8k9VEyf9WgVq5DRrEzf5V6kaYP30S7g9BV9jKtaQ@mail.gmail.com/
[2] https://lore.kernel.org/openbmc/CAP6Zq1h1if4hyubyh6N8EOdGOu+zp0qVUimF-9L2eXZ-QFAYjw@mail.gmail.com/
[3] https://lore.kernel.org/all/20191211194624.2872-1-jae.hyun.yoo@linux.intel.com/
[4] https://lore.kernel.org/all/20220208153639.255278-1-iwona.winiarska@intel.com/

Changes v1 -> v2:

* Renamed binding filename to match compatible (Krzysztof)
* Removed period from the end of copyright (Paul)

Thanks
-Iwona

Iwona Winiarska (2):
  ARM: dts: nuvoton: Add PECI controller node
  arm64: dts: nuvoton: Add PECI controller node

Tomer Maimon (2):
  dt-bindings: Add bindings for peci-npcm
  peci: Add peci-npcm controller driver

 .../bindings/peci/nuvoton,npcm-peci.yaml      |  56 ++++
 .../dts/nuvoton/nuvoton-common-npcm7xx.dtsi   |   9 +
 .../dts/nuvoton/nuvoton-common-npcm8xx.dtsi   |   9 +
 drivers/peci/controller/Kconfig               |  16 +
 drivers/peci/controller/Makefile              |   1 +
 drivers/peci/controller/peci-npcm.c           | 298 ++++++++++++++++++
 6 files changed, 389 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/peci/nuvoton,npcm-peci.yaml
 create mode 100644 drivers/peci/controller/peci-npcm.c

-- 
2.40.1

[PATCH v2 1/4] dt-bindings: Add bindings for peci-npcm

[Iwona Winiarska]

From: Tomer Maimon <tmaimon77@gmail.com>

Add device tree bindings for the peci-npcm controller driver.

Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Tyrone Ting <warp5tw@gmail.com>
Co-developed-by: Iwona Winiarska <iwona.winiarska@intel.com>
Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
---
Changes v1 -> v2:

* Renamed binding filename to match compatible (Krzysztof)
---
 .../bindings/peci/nuvoton,npcm-peci.yaml      | 56 +++++++++++++++++++
 1 file changed, 56 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/peci/nuvoton,npcm-peci.yaml

diff --git a/Documentation/devicetree/bindings/peci/nuvoton,npcm-peci.yaml b/Documentation/devicetree/bindings/peci/nuvoton,npcm-peci.yaml
new file mode 100644
index 000000000000..6eafa9ccaa54
--- /dev/null
+++ b/Documentation/devicetree/bindings/peci/nuvoton,npcm-peci.yaml
@@ -0,0 +1,56 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/peci/peci-npcm.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Nuvoton PECI Bus
+
+maintainers:
+  - Tomer Maimon <tmaimon77@gmail.com>
+
+allOf:
+  - $ref: peci-controller.yaml#
+
+properties:
+  compatible:
+    enum:
+      - nuvoton,npcm750-peci
+      - nuvoton,npcm845-peci
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    description:
+      Clock source for PECI controller. Should reference the APB clock.
+    maxItems: 1
+
+  cmd-timeout-ms:
+    minimum: 1
+    maximum: 1000
+    default: 1000
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/nuvoton,npcm7xx-clock.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    peci-controller@f0100000 {
+      compatible = "nuvoton,npcm750-peci";
+      reg = <0xf0100000 0x200>;
+      interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+      clocks = <&clk NPCM7XX_CLK_APB3>;
+      cmd-timeout-ms = <1000>;
+    };
+...
-- 
2.40.1

[PATCH v2 2/4] peci: Add peci-npcm controller driver

[Iwona Winiarska]

From: Tomer Maimon <tmaimon77@gmail.com>

Add support for Nuvoton NPCM BMC hardware to the Platform Environment
Control Interface (PECI) subsystem.

Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Tyrone Ting <warp5tw@gmail.com>
Co-developed-by: Iwona Winiarska <iwona.winiarska@intel.com>
Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
---
Changes v1 -> v2:

* Removed period from the end of copyright (Paul)
---
 drivers/peci/controller/Kconfig     |  16 ++
 drivers/peci/controller/Makefile    |   1 +
 drivers/peci/controller/peci-npcm.c | 298 ++++++++++++++++++++++++++++
 3 files changed, 315 insertions(+)
 create mode 100644 drivers/peci/controller/peci-npcm.c

diff --git a/drivers/peci/controller/Kconfig b/drivers/peci/controller/Kconfig
index 2fc5e2abb74a..4f9c245ad042 100644
--- a/drivers/peci/controller/Kconfig
+++ b/drivers/peci/controller/Kconfig
@@ -16,3 +16,19 @@ config PECI_ASPEED
 
 	  This driver can also be built as a module. If so, the module will
 	  be called peci-aspeed.
+
+config PECI_NPCM
+	tristate "Nuvoton NPCM PECI support"
+	depends on ARCH_NPCM || COMPILE_TEST
+	depends on OF
+	select REGMAP_MMIO
+	help
+	  This option enables PECI controller driver for Nuvoton NPCM7XX
+	  and NPCM8XX SoCs. It allows BMC to discover devices connected
+	  to it and communicate with them using PECI protocol.
+
+	  Say Y here if you want support for the Platform Environment Control
+	  Interface (PECI) bus adapter driver on the Nuvoton NPCM SoCs.
+
+	  This support is also available as a module. If so, the module
+	  will be called peci-npcm.
diff --git a/drivers/peci/controller/Makefile b/drivers/peci/controller/Makefile
index 022c28ef1bf0..e247449bb423 100644
--- a/drivers/peci/controller/Makefile
+++ b/drivers/peci/controller/Makefile
@@ -1,3 +1,4 @@
 # SPDX-License-Identifier: GPL-2.0-only
 
 obj-$(CONFIG_PECI_ASPEED)	+= peci-aspeed.o
+obj-$(CONFIG_PECI_NPCM)		+= peci-npcm.o
diff --git a/drivers/peci/controller/peci-npcm.c b/drivers/peci/controller/peci-npcm.c
new file mode 100644
index 000000000000..ec613d35c796
--- /dev/null
+++ b/drivers/peci/controller/peci-npcm.c
@@ -0,0 +1,298 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2019 Nuvoton Technology corporation
+
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/interrupt.h>
+#include <linux/jiffies.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/peci.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+/* NPCM GCR module */
+#define NPCM_INTCR3_OFFSET	0x9C
+#define NPCM_INTCR3_PECIVSEL	BIT(19)
+
+/* NPCM PECI Registers */
+#define NPCM_PECI_CTL_STS	0x00
+#define NPCM_PECI_RD_LENGTH	0x04
+#define NPCM_PECI_ADDR		0x08
+#define NPCM_PECI_CMD		0x0C
+#define NPCM_PECI_CTL2		0x10
+#define NPCM_PECI_WR_LENGTH	0x1C
+#define NPCM_PECI_PDDR		0x2C
+#define NPCM_PECI_DAT_INOUT(n)	(0x100 + ((n) * 4))
+
+#define NPCM_PECI_MAX_REG	0x200
+
+/* NPCM_PECI_CTL_STS - 0x00 : Control Register */
+#define NPCM_PECI_CTRL_DONE_INT_EN	BIT(6)
+#define NPCM_PECI_CTRL_ABRT_ERR		BIT(4)
+#define NPCM_PECI_CTRL_CRC_ERR		BIT(3)
+#define NPCM_PECI_CTRL_DONE		BIT(1)
+#define NPCM_PECI_CTRL_START_BUSY	BIT(0)
+
+/* NPCM_PECI_RD_LENGTH - 0x04 : Command Register */
+#define NPCM_PECI_RD_LEN_MASK		GENMASK(6, 0)
+
+/* NPCM_PECI_CMD - 0x10 : Command Register */
+#define NPCM_PECI_CTL2_MASK		GENMASK(7, 6)
+
+/* NPCM_PECI_WR_LENGTH - 0x1C : Command Register */
+#define NPCM_PECI_WR_LEN_MASK		GENMASK(6, 0)
+
+/* NPCM_PECI_PDDR - 0x2C : Command Register */
+#define NPCM_PECI_PDDR_MASK		GENMASK(4, 0)
+
+#define NPCM_PECI_INT_MASK		(NPCM_PECI_CTRL_ABRT_ERR | \
+					 NPCM_PECI_CTRL_CRC_ERR  | \
+					 NPCM_PECI_CTRL_DONE)
+
+#define NPCM_PECI_IDLE_CHECK_TIMEOUT_USEC	(50 * USEC_PER_MSEC)
+#define NPCM_PECI_IDLE_CHECK_INTERVAL_USEC	(10 * USEC_PER_MSEC)
+#define NPCM_PECI_CMD_TIMEOUT_MS_DEFAULT	1000
+#define NPCM_PECI_CMD_TIMEOUT_MS_MAX		60000
+#define NPCM_PECI_HOST_NEG_BIT_RATE_DEFAULT	15
+#define NPCM_PECI_PULL_DOWN_DEFAULT		0
+
+struct npcm_peci {
+	u32			cmd_timeout_ms;
+	struct completion	xfer_complete;
+	struct regmap		*regmap;
+	u32			status;
+	spinlock_t		lock; /* to sync completion status handling */
+	struct peci_controller *controller;
+	struct device		*dev;
+	struct clk		*clk;
+	int			irq;
+};
+
+static int npcm_peci_xfer(struct peci_controller *controller, u8 addr, struct peci_request *req)
+{
+	struct npcm_peci *priv = dev_get_drvdata(controller->dev.parent);
+	unsigned long timeout = msecs_to_jiffies(priv->cmd_timeout_ms);
+	unsigned int msg_rd;
+	u32 cmd_sts;
+	int i, ret;
+
+	/* Check command sts and bus idle state */
+	ret = regmap_read_poll_timeout(priv->regmap, NPCM_PECI_CTL_STS, cmd_sts,
+				       !(cmd_sts & NPCM_PECI_CTRL_START_BUSY),
+				       NPCM_PECI_IDLE_CHECK_INTERVAL_USEC,
+				       NPCM_PECI_IDLE_CHECK_TIMEOUT_USEC);
+	if (ret)
+		return ret; /* -ETIMEDOUT */
+
+	spin_lock_irq(&priv->lock);
+	reinit_completion(&priv->xfer_complete);
+
+	regmap_write(priv->regmap, NPCM_PECI_ADDR, addr);
+	regmap_write(priv->regmap, NPCM_PECI_RD_LENGTH, NPCM_PECI_WR_LEN_MASK & req->rx.len);
+	regmap_write(priv->regmap, NPCM_PECI_WR_LENGTH, NPCM_PECI_WR_LEN_MASK & req->tx.len);
+
+	if (req->tx.len) {
+		regmap_write(priv->regmap, NPCM_PECI_CMD, req->tx.buf[0]);
+
+		for (i = 0; i < (req->tx.len - 1); i++)
+			regmap_write(priv->regmap, NPCM_PECI_DAT_INOUT(i), req->tx.buf[i + 1]);
+	}
+
+#if IS_ENABLED(CONFIG_DYNAMIC_DEBUG)
+	dev_dbg(priv->dev, "addr : %#02x, tx.len : %#02x, rx.len : %#02x\n",
+		addr, req->tx.len, req->rx.len);
+	print_hex_dump_bytes("TX : ", DUMP_PREFIX_NONE, req->tx.buf, req->tx.len);
+#endif
+
+	priv->status = 0;
+	regmap_update_bits(priv->regmap, NPCM_PECI_CTL_STS, NPCM_PECI_CTRL_START_BUSY,
+			   NPCM_PECI_CTRL_START_BUSY);
+
+	spin_unlock_irq(&priv->lock);
+
+	ret = wait_for_completion_interruptible_timeout(&priv->xfer_complete, timeout);
+	if (ret < 0)
+		return ret;
+
+	if (ret == 0) {
+		dev_dbg(priv->dev, "timeout waiting for a response\n");
+		return -ETIMEDOUT;
+	}
+
+	spin_lock_irq(&priv->lock);
+
+	if (priv->status != NPCM_PECI_CTRL_DONE) {
+		spin_unlock_irq(&priv->lock);
+		dev_dbg(priv->dev, "no valid response, status: %#02x\n", priv->status);
+		return -EIO;
+	}
+
+	regmap_write(priv->regmap, NPCM_PECI_CMD, 0);
+
+	for (i = 0; i < req->rx.len; i++) {
+		regmap_read(priv->regmap, NPCM_PECI_DAT_INOUT(i), &msg_rd);
+		req->rx.buf[i] = (u8)msg_rd;
+	}
+
+	spin_unlock_irq(&priv->lock);
+
+#if IS_ENABLED(CONFIG_DYNAMIC_DEBUG)
+	print_hex_dump_bytes("RX : ", DUMP_PREFIX_NONE, req->rx.buf, req->rx.len);
+#endif
+	return 0;
+}
+
+static irqreturn_t npcm_peci_irq_handler(int irq, void *arg)
+{
+	struct npcm_peci *priv = arg;
+	u32 status_ack = 0;
+	u32 status;
+
+	spin_lock(&priv->lock);
+	regmap_read(priv->regmap, NPCM_PECI_CTL_STS, &status);
+	priv->status |= (status & NPCM_PECI_INT_MASK);
+
+	if (status & NPCM_PECI_CTRL_CRC_ERR)
+		status_ack |= NPCM_PECI_CTRL_CRC_ERR;
+
+	if (status & NPCM_PECI_CTRL_ABRT_ERR)
+		status_ack |= NPCM_PECI_CTRL_ABRT_ERR;
+
+	/*
+	 * All commands should be ended up with a NPCM_PECI_CTRL_DONE
+	 * bit set even in an error case.
+	 */
+	if (status & NPCM_PECI_CTRL_DONE) {
+		status_ack |= NPCM_PECI_CTRL_DONE;
+		complete(&priv->xfer_complete);
+	}
+
+	regmap_write_bits(priv->regmap, NPCM_PECI_CTL_STS, NPCM_PECI_INT_MASK, status_ack);
+
+	spin_unlock(&priv->lock);
+	return IRQ_HANDLED;
+}
+
+static int npcm_peci_init_ctrl(struct npcm_peci *priv)
+{
+	u32 cmd_sts;
+	int ret;
+
+	priv->clk = devm_clk_get_enabled(priv->dev, NULL);
+	if (IS_ERR(priv->clk)) {
+		dev_err(priv->dev, "failed to get ref clock\n");
+		return PTR_ERR(priv->clk);
+	}
+
+	ret = device_property_read_u32(priv->dev, "cmd-timeout-ms", &priv->cmd_timeout_ms);
+	if (ret) {
+		priv->cmd_timeout_ms = NPCM_PECI_CMD_TIMEOUT_MS_DEFAULT;
+	} else if (priv->cmd_timeout_ms > NPCM_PECI_CMD_TIMEOUT_MS_MAX ||
+		   priv->cmd_timeout_ms == 0) {
+		dev_warn(priv->dev, "invalid cmd-timeout-ms: %u, falling back to: %u\n",
+			 priv->cmd_timeout_ms, NPCM_PECI_CMD_TIMEOUT_MS_DEFAULT);
+
+		priv->cmd_timeout_ms = NPCM_PECI_CMD_TIMEOUT_MS_DEFAULT;
+	}
+
+	regmap_update_bits(priv->regmap, NPCM_PECI_CTL2, NPCM_PECI_CTL2_MASK,
+			   NPCM_PECI_PULL_DOWN_DEFAULT << 6);
+
+	regmap_update_bits(priv->regmap, NPCM_PECI_PDDR, NPCM_PECI_PDDR_MASK,
+			   NPCM_PECI_HOST_NEG_BIT_RATE_DEFAULT);
+
+	ret = regmap_read_poll_timeout(priv->regmap, NPCM_PECI_CTL_STS, cmd_sts,
+				       !(cmd_sts & NPCM_PECI_CTRL_START_BUSY),
+				       NPCM_PECI_IDLE_CHECK_INTERVAL_USEC,
+				       NPCM_PECI_IDLE_CHECK_TIMEOUT_USEC);
+	if (ret)
+		return ret; /* -ETIMEDOUT */
+
+	/* PECI interrupt enable */
+	regmap_update_bits(priv->regmap, NPCM_PECI_CTL_STS, NPCM_PECI_CTRL_DONE_INT_EN,
+			   NPCM_PECI_CTRL_DONE_INT_EN);
+
+	return 0;
+}
+
+static const struct regmap_config npcm_peci_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.max_register = NPCM_PECI_MAX_REG,
+	.fast_io = true,
+};
+
+static struct peci_controller_ops npcm_ops = {
+	.xfer = npcm_peci_xfer,
+};
+
+static int npcm_peci_probe(struct platform_device *pdev)
+{
+	struct peci_controller *controller;
+	struct npcm_peci *priv;
+	void __iomem *base;
+	int ret;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->dev = &pdev->dev;
+	dev_set_drvdata(&pdev->dev, priv);
+
+	base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	priv->regmap = devm_regmap_init_mmio(&pdev->dev, base, &npcm_peci_regmap_config);
+	if (IS_ERR(priv->regmap))
+		return PTR_ERR(priv->regmap);
+
+	priv->irq = platform_get_irq(pdev, 0);
+	if (priv->irq < 0)
+		return priv->irq;
+
+	ret = devm_request_irq(&pdev->dev, priv->irq, npcm_peci_irq_handler,
+			       0, "peci-npcm-irq", priv);
+	if (ret)
+		return ret;
+
+	init_completion(&priv->xfer_complete);
+	spin_lock_init(&priv->lock);
+
+	ret = npcm_peci_init_ctrl(priv);
+	if (ret)
+		return ret;
+
+	controller = devm_peci_controller_add(priv->dev, &npcm_ops);
+	if (IS_ERR(controller))
+		return dev_err_probe(priv->dev, PTR_ERR(controller),
+				     "failed to add npcm peci controller\n");
+
+	priv->controller = controller;
+
+	return 0;
+}
+
+static const struct of_device_id npcm_peci_of_table[] = {
+	{ .compatible = "nuvoton,npcm750-peci", },
+	{ .compatible = "nuvoton,npcm845-peci", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, npcm_peci_of_table);
+
+static struct platform_driver npcm_peci_driver = {
+	.probe  = npcm_peci_probe,
+	.driver = {
+		.name           = KBUILD_MODNAME,
+		.of_match_table = npcm_peci_of_table,
+	},
+};
+module_platform_driver(npcm_peci_driver);
+
+MODULE_AUTHOR("Tomer Maimon <tomer.maimon@nuvoton.com>");
+MODULE_DESCRIPTION("NPCM PECI driver");
+MODULE_LICENSE("GPL");
+MODULE_IMPORT_NS(PECI);
-- 
2.40.1

[PATCH v2 3/4] ARM: dts: nuvoton: Add PECI controller node

[Iwona Winiarska]

Add PECI controller node with all required information.

Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
---
 arch/arm/boot/dts/nuvoton/nuvoton-common-npcm7xx.dtsi | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/arch/arm/boot/dts/nuvoton/nuvoton-common-npcm7xx.dtsi b/arch/arm/boot/dts/nuvoton/nuvoton-common-npcm7xx.dtsi
index c7b5ef15b716..cccc33441050 100644
--- a/arch/arm/boot/dts/nuvoton/nuvoton-common-npcm7xx.dtsi
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-common-npcm7xx.dtsi
@@ -220,6 +220,15 @@ kcs3: kcs3@0 {
 				};
 			};
 
+			peci0: peci-controller@f0100000 {
+				compatible = "nuvoton,npcm750-peci";
+				reg = <0xf0100000 0x200>;
+				interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk NPCM7XX_CLK_APB3>;
+				cmd-timeout-ms = <1000>;
+				status = "disabled";
+			};
+
 			spi0: spi@200000 {
 				compatible = "nuvoton,npcm750-pspi";
 				reg = <0x200000 0x1000>;
-- 
2.40.1

[PATCH v2 4/4] arm64: dts: nuvoton: Add PECI controller node

[Iwona Winiarska]

Add PECI controller node with all required information.

Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
---
 arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi b/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi
index aa7aac8c3774..b8326bbe9fde 100644
--- a/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi
+++ b/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi
@@ -68,6 +68,15 @@ apb {
 			ranges = <0x0 0x0 0xf0000000 0x00300000>,
 				<0xfff00000 0x0 0xfff00000 0x00016000>;
 
+			peci0: peci-controller@100000 {
+				compatible = "nuvoton,npcm845-peci";
+				reg = <0x100000 0x1000>;
+				interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk NPCM8XX_CLK_APB3>;
+				cmd-timeout-ms = <1000>;
+				status = "disabled";
+			};
+
 			timer0: timer@8000 {
 				compatible = "nuvoton,npcm845-timer";
 				interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
-- 
2.40.1

Re: [PATCH v2 1/4] dt-bindings: Add bindings for peci-npcm

[Krzysztof Kozlowski]

On 26/07/2023 21:27, Iwona Winiarska wrote:
> From: Tomer Maimon <tmaimon77@gmail.com>
> 
> Add device tree bindings for the peci-npcm controller driver.
> 
> Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
> Signed-off-by: Tyrone Ting <warp5tw@gmail.com>
> Co-developed-by: Iwona Winiarska <iwona.winiarska@intel.com>
> Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
> ---
> Changes v1 -> v2:
> 
> * Renamed binding filename to match compatible (Krzysztof)


Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

Re: [PATCH v2 1/4] dt-bindings: Add bindings for peci-npcm

[Rob Herring]

On Wed, 26 Jul 2023 21:27:37 +0200, Iwona Winiarska wrote:
> From: Tomer Maimon <tmaimon77@gmail.com>
> 
> Add device tree bindings for the peci-npcm controller driver.
> 
> Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
> Signed-off-by: Tyrone Ting <warp5tw@gmail.com>
> Co-developed-by: Iwona Winiarska <iwona.winiarska@intel.com>
> Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
> ---
> Changes v1 -> v2:
> 
> * Renamed binding filename to match compatible (Krzysztof)
> ---
>  .../bindings/peci/nuvoton,npcm-peci.yaml      | 56 +++++++++++++++++++
>  1 file changed, 56 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/peci/nuvoton,npcm-peci.yaml
> 

My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):

yamllint warnings/errors:

dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/peci/nuvoton,npcm-peci.yaml: $id: Cannot determine base path from $id, relative path/filename doesn't match actual path or filename
 	 $id: http://devicetree.org/schemas/peci/peci-npcm.yaml
 	file: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/peci/nuvoton,npcm-peci.yaml

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230726192740.1383740-2-iwona.winiarska@intel.com

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.

Re: [PATCH v2 1/4] dt-bindings: Add bindings for peci-npcm

[Krzysztof Kozlowski]

On 26/07/2023 21:39, Krzysztof Kozlowski wrote:
> On 26/07/2023 21:27, Iwona Winiarska wrote:
>> From: Tomer Maimon <tmaimon77@gmail.com>
>>
>> Add device tree bindings for the peci-npcm controller driver.
>>
>> Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
>> Signed-off-by: Tyrone Ting <warp5tw@gmail.com>
>> Co-developed-by: Iwona Winiarska <iwona.winiarska@intel.com>
>> Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
>> ---
>> Changes v1 -> v2:
>>
>> * Renamed binding filename to match compatible (Krzysztof)
> 
> 
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
>

Un-reviewed. Why testing the code before sending to LKML? Obviously not
needed.

Best regards,
Krzysztof

Re: [PATCH v2 1/4] dt-bindings: Add bindings for peci-npcm

[Winiarska, Iwona]

On Wed, 2023-07-26 at 14:14 -0600, Rob Herring wrote:
> 
> On Wed, 26 Jul 2023 21:27:37 +0200, Iwona Winiarska wrote:
> > From: Tomer Maimon <tmaimon77@gmail.com>
> > 
> > Add device tree bindings for the peci-npcm controller driver.
> > 
> > Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
> > Signed-off-by: Tyrone Ting <warp5tw@gmail.com>
> > Co-developed-by: Iwona Winiarska <iwona.winiarska@intel.com>
> > Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
> > ---
> > Changes v1 -> v2:
> > 
> > * Renamed binding filename to match compatible (Krzysztof)
> > ---
> >  .../bindings/peci/nuvoton,npcm-peci.yaml      | 56 +++++++++++++++++++
> >  1 file changed, 56 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/peci/nuvoton,npcm-
> > peci.yaml
> > 
> 
> My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
> on your patch (DT_CHECKER_FLAGS is new in v5.13):
> 
> yamllint warnings/errors:
> 
> dtschema/dtc warnings/errors:
> /builds/robherring/dt-review-
> ci/linux/Documentation/devicetree/bindings/peci/nuvoton,npcm-peci.yaml: $id:
> Cannot determine base path from $id, relative path/filename doesn't match
> actual path or filename
>          $id: http://devicetree.org/schemas/peci/peci-npcm.yaml
>         file: /builds/robherring/dt-review-
> ci/linux/Documentation/devicetree/bindings/peci/nuvoton,npcm-peci.yaml

Oops, sorry about that - I'll send v3.

Thanks
-Iwona

> 
> doc reference errors (make refcheckdocs):
> 
> See
> https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230726192740.1383740-2-iwona.winiarska@intel.com
> 
> The base for the series is generally the latest rc1. A different dependency
> should be noted in *this* patch.
> 
> If you already ran 'make dt_binding_check' and didn't see the above
> error(s), then make sure 'yamllint' is installed and dt-schema is up to
> date:
> 
> pip3 install dtschema --upgrade
> 
> Please check and re-submit after running the above command yourself. Note
> that DT_SCHEMA_FILES can be set to your schema file to speed up checking
> your schema. However, it must be unset to test all examples with your schema.
>