Re: [PATCH 07/13] dt-bindings: media: camss: Add qcom,sm8550-camss binding

[Neil Armstrong <neil.armstrong@linaro.org>]

On 12/09/2024 13:41, Bryan O'Donoghue wrote:
> On 12/09/2024 09:22, Vladimir Zapolskiy wrote:
>>> +
>>> +  vdda-phy-supply:
>>> +    description:
>>> +      Phandle to a regulator supply to PHY core block.
>>> +
>>> +  vdda-pll-supply:
>>> +    description:
>>> +      Phandle to 1.2V regulator supply to PHY refclk pll block.
>>> +
>>
>> Here the supplies should be split into ones, which are specific to CSI blocks,
>> and I believe they shall be set as optional.
> 
> In principle I agree with that, each CSIPHY should have its own vdda-phy and vdda-pll regulator specified.
> 
> In practice though I don't believe its necessary, below.
> 
>> The proposed names are:
>>
>> vdda-phy-01-supply
>> vdda-pll-01-supply
>> vdda-phy-23-supply
>> vdda-pll-23-supply
>> vdda-phy-46-supply
>> vdda-pll-46-supply
>> vdda-phy-57-supply
>> vdda-pll-57-supply
> 
> In principle, you're right, we need to expand the name set here.
> 
>> I understand that what I ask is much more clumsy, and it could be seen even as
>> unneeded, however it'll be the right set of properties to describe the CAMSS IP
>> in this respect
> I think the following naming would be better as it matches the power-grid naming in the docs.
> 
> csiphyX-vdda-phy-supply
> csiphyX-vdda-pll-supply
> 
> =>
> 
> // voltage domain = vdd_a_csi_01_09 = regulator l1e
> csiphy0-vdda-phy-supply = <&vreg_l1e_0p9>;
> 
> // voltage domain = vdd_a_csi_01_1p2 = regulator l3e
> csiphy0-vdda-pll-supply = <&vreg_l3e_1p2>;
> 
> //
> csiphy1-vdda-phy-supply = <&vreg_l1e_0p9>;
> csiphy1-vdda-pll-supply = <&vreg_l3e_1p2>;
> 
> Where X indicates the CSIPHY number.
> 
> So in fact, in practice we don't need to differentiate these entries.
> 
> Checking x1e80100 ...
> 
> csiphy0
> 
> vdda-phy-supply = <&vreg_l2c_0p9>;
> vdda-pll-supply = <&vreg_l1c_1p2>;
> 
> This is also the case for csiphy 1/2/4
> 
> So, I _don't_ believe this is work we need to do, since its the same regulator for each PHY.

Except when it's not the case, like on the SM8650 HDK:
VDD_A_CSI_01_0P9	=> VREG_L2I_0P88
VDD_A_CSI_01_1P2	=> VREG_L3I_1P2
VDD_A_CSI_24_0P9	=> VREG_L1I_0P88
VDD_A_CSI_24_1P2	=> VREG_L3I_1P2
VDD_A_CSI_35_0P9	=> VREG_L2I_0P88
VDD_A_CSI_35_1P2	=> VREG_L3I_1P2

the 1P2 all uses VREG_L3I_1P2, while the 0P9 are using VREG_L2I_0P88 or VREG_L1I_0P88

Not declaring the exact supplies is pure lazyness, it will bounce back at our faces at some point.

Neil

> 
> ---
> bod