[PATCH V4 0/6] ARM: dts: imx6ull: Add chargebyte Tarragon support

[PATCH V4 0/6] ARM: dts: imx6ull: Add chargebyte Tarragon support

[Stefan Wahren]

This series adds the support for chargebyte Tarragon, which is an Electrical
Vehicle Supply Equipment (EVSE) for AC charging stations
(according to IEC 61851, ISO 15118).

The Tarragon board is based on an i.MX6ULL SoC and is available in
4 variants (Master, Slave, SlaveXT, Micro), which provide more or
less peripherals.

Supported features:
  * 512 MB DDR RAM
  * eMMC
  * Debug UART
  * 100 Mbit Ethernet
  * USB 2.0 Host interface
  * Powerline communication (QCA700x)
  * 2x RS485
  * Digital in- and outputs (12 V)
  * One-Wire master for external temp sensors
  * 2x relay outputs
  * 2x motor interfaces
  
The Tarragon hardware is bundled with a charging stack under the name Charge Control C: 
https://chargebyte.com/products/charging-station-communication/charge-control-c

This series is rebased on top of:
https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git?h=for-next

Changes in V4:
- introduce dedicated dt-binding for Maxim I2C to 1-W bridges
- add Krzysztof's Acked-by

Changes in V3:
- dropped already applied iio patches
- renamed pinctrl_qca700x_mains_spi to pinctrl_ecspi4
- dropped Tarragon container nodes as suggested by Shawn
- sort the pinctrl groups alphabetically also suggested by Shawn

Changes in V2:
- after fixing technical problems send patches directly from chargebyte address
  and drop the related signed-off-by
- add Krzysztof's Acked-by
- improve commit messages (patch 3, 4, 5)
- make iis328dq fallback to lis331dl as suggested by Jonathan
- fix order of Tarragon entries in FSL schema
- improve Tarragon led node names and drop label as suggested by Krzysztof
- change Tarragon SVNS pinctrl settings after internal discussion
  with chargebyte hardware team
- drop broken-cd in Tarragon common DTSI which is not necessary for eMMC
- add no-sd and no-sdio for eMMC interface of Tarragon

Stefan Wahren (6):
  dt-bindings: vendor-prefixes: add chargebyte
  dt-bindings: w1: Add DS2482/DS2484 I2C to 1-W bridges
  w1: ds2482: add i2c id for DS2484
  dt-bindings: ARM: fsl: Add chargebyte Tarragon
  ARM: dts: imx6ull: Add chargebyte Tarragon support
  ARM: imx_v6_v7_defconfig: Enable Tarragon peripheral drivers

 .../devicetree/bindings/arm/fsl.yaml          |   9 +
 .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
 .../devicetree/bindings/w1/maxim,ds2482.yaml  |  43 +
 arch/arm/boot/dts/Makefile                    |   4 +
 .../arm/boot/dts/imx6ull-tarragon-common.dtsi | 852 ++++++++++++++++++
 arch/arm/boot/dts/imx6ull-tarragon-master.dts |  82 ++
 arch/arm/boot/dts/imx6ull-tarragon-micro.dts  |  10 +
 arch/arm/boot/dts/imx6ull-tarragon-slave.dts  |  32 +
 .../arm/boot/dts/imx6ull-tarragon-slavext.dts |  64 ++
 arch/arm/configs/imx_v6_v7_defconfig          |   6 +
 drivers/w1/masters/ds2482.c                   |   1 +
 11 files changed, 1105 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/w1/maxim,ds2482.yaml
 create mode 100644 arch/arm/boot/dts/imx6ull-tarragon-common.dtsi
 create mode 100644 arch/arm/boot/dts/imx6ull-tarragon-master.dts
 create mode 100644 arch/arm/boot/dts/imx6ull-tarragon-micro.dts
 create mode 100644 arch/arm/boot/dts/imx6ull-tarragon-slave.dts
 create mode 100644 arch/arm/boot/dts/imx6ull-tarragon-slavext.dts

-- 
2.17.1

[PATCH V4 1/6] dt-bindings: vendor-prefixes: add chargebyte

[Stefan Wahren]

chargebyte supplies hardware and software products for all
aspects of charging communication.
https://chargebyte.com/

Signed-off-by: Stefan Wahren <stefan.wahren@chargebyte.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index ed64e06ecca4..b8d8fa1d1fd6 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -240,6 +240,8 @@ patternProperties:
     description: CellWise Microelectronics Co., Ltd
   "^ceva,.*":
     description: Ceva, Inc.
+  "^chargebyte,.*":
+    description: chargebyte GmbH
   "^checkpoint,.*":
     description: Check Point Software Technologies Ltd.
   "^chefree,.*":
-- 
2.17.1

[PATCH V4 2/6] dt-bindings: w1: Add DS2482/DS2484 I2C to 1-W bridges

[Stefan Wahren]

Even this binding look trivial, the actual hardware supports more
features (e.g. sleep mode control GPIO). So add this as a dedicated
devicetree binding for the Maxim DS2482/DS2484 I2C to 1-W bridges,
which can be extended later.

Signed-off-by: Stefan Wahren <stefan.wahren@chargebyte.com>
---
 .../devicetree/bindings/w1/maxim,ds2482.yaml  | 43 +++++++++++++++++++
 1 file changed, 43 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/w1/maxim,ds2482.yaml

diff --git a/Documentation/devicetree/bindings/w1/maxim,ds2482.yaml b/Documentation/devicetree/bindings/w1/maxim,ds2482.yaml
new file mode 100644
index 000000000000..fd692a3a7400
--- /dev/null
+++ b/Documentation/devicetree/bindings/w1/maxim,ds2482.yaml
@@ -0,0 +1,43 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/w1/maxim,ds2482.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Maxim One wire bus master controller
+
+maintainers:
+  - Stefan Wahren <stefan.wahren@chargebyte.com>
+
+description: |
+  I2C to 1-wire bridges
+
+  https://www.analog.com/media/en/technical-documentation/data-sheets/ds2482-100.pdf
+  https://www.analog.com/media/en/technical-documentation/data-sheets/DS2482-800.pdf
+  https://www.analog.com/media/en/technical-documentation/data-sheets/DS2484.pdf
+
+properties:
+  compatible:
+    enum:
+      - maxim,ds2482
+      - maxim,ds2484
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+      onewire@18 {
+        compatible = "maxim,ds2484";
+        reg = <0x18>;
+      };
+    };
-- 
2.17.1

[PATCH V4 3/6] w1: ds2482: add i2c id for DS2484

[Stefan Wahren]

The DS2484 is compatible to the DS2482-100, but also supports a
pin-controlled power-saving sleep mode.

Link: https://www.analog.com/media/en/technical-documentation/data-sheets/DS2484.pdf
Signed-off-by: Stefan Wahren <stefan.wahren@chargebyte.com>
---
 drivers/w1/masters/ds2482.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/w1/masters/ds2482.c b/drivers/w1/masters/ds2482.c
index 62c44616d8a9..6f6df686e9ad 100644
--- a/drivers/w1/masters/ds2482.c
+++ b/drivers/w1/masters/ds2482.c
@@ -545,6 +545,7 @@ static void ds2482_remove(struct i2c_client *client)
  */
 static const struct i2c_device_id ds2482_id[] = {
 	{ "ds2482", 0 },
+	{ "ds2484", 0 },
 	{ }
 };
 MODULE_DEVICE_TABLE(i2c, ds2482_id);
-- 
2.17.1

[PATCH V4 4/6] dt-bindings: ARM: fsl: Add chargebyte Tarragon

[Stefan Wahren]

This adds the compatibles for the chargebyte Tarragon boards.

Signed-off-by: Stefan Wahren <stefan.wahren@chargebyte.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 Documentation/devicetree/bindings/arm/fsl.yaml | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index b175f2b1bd30..7fac7f834814 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -707,6 +707,15 @@ properties:
           - const: armadeus,imx6ull-opos6ul     # OPOS6UL (i.MX6ULL) SoM
           - const: fsl,imx6ull
 
+      - description: i.MX6ULL chargebyte Tarragon Boards
+        items:
+          - enum:
+              - chargebyte,imx6ull-tarragon-master
+              - chargebyte,imx6ull-tarragon-micro
+              - chargebyte,imx6ull-tarragon-slave
+              - chargebyte,imx6ull-tarragon-slavext
+          - const: fsl,imx6ull
+
       - description: i.MX6ULL DHCOM SoM based Boards
         items:
           - enum:
-- 
2.17.1

[PATCH V4 5/6] ARM: dts: imx6ull: Add chargebyte Tarragon support

[Stefan Wahren]

This adds the support for chargebyte Tarragon, which is an Electrical
Vehicle Supply Equipment (EVSE) for AC charging stations
(according to IEC 61851, ISO 15118).

The Tarragon board is based on an i.MX6ULL SoC and is available in
4 variants (Master, Slave, SlaveXT, Micro), which provide more or
less peripherals.

Supported features:
  * 512 MB DDR RAM
  * eMMC
  * Debug UART
  * 100 Mbit Ethernet
  * USB 2.0 Host interface
  * Powerline communication (QCA700x)
  * 2x RS485
  * Digital in- and outputs (12 V)
  * One-Wire master for external temp sensors
  * 2x relay outputs
  * 2x motor interfaces

Link: https://chargebyte.com/products/charging-station-communication/charge-control-c
Signed-off-by: Stefan Wahren <stefan.wahren@chargebyte.com>
---
 arch/arm/boot/dts/Makefile                    |   4 +
 .../arm/boot/dts/imx6ull-tarragon-common.dtsi | 852 ++++++++++++++++++
 arch/arm/boot/dts/imx6ull-tarragon-master.dts |  82 ++
 arch/arm/boot/dts/imx6ull-tarragon-micro.dts  |  10 +
 arch/arm/boot/dts/imx6ull-tarragon-slave.dts  |  32 +
 .../arm/boot/dts/imx6ull-tarragon-slavext.dts |  64 ++
 6 files changed, 1044 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6ull-tarragon-common.dtsi
 create mode 100644 arch/arm/boot/dts/imx6ull-tarragon-master.dts
 create mode 100644 arch/arm/boot/dts/imx6ull-tarragon-micro.dts
 create mode 100644 arch/arm/boot/dts/imx6ull-tarragon-slave.dts
 create mode 100644 arch/arm/boot/dts/imx6ull-tarragon-slavext.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index fd4f7230cb55..404e6f5a1cc7 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -760,6 +760,10 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
 	imx6ull-phytec-segin-lc-rdk-nand.dtb \
 	imx6ull-phytec-tauri-emmc.dtb \
 	imx6ull-phytec-tauri-nand.dtb \
+	imx6ull-tarragon-master.dtb \
+	imx6ull-tarragon-micro.dtb \
+	imx6ull-tarragon-slave.dtb \
+	imx6ull-tarragon-slavext.dtb \
 	imx6ull-tqma6ull2-mba6ulx.dtb \
 	imx6ull-tqma6ull2l-mba6ulx.dtb \
 	imx6ulz-14x14-evk.dtb \
diff --git a/arch/arm/boot/dts/imx6ull-tarragon-common.dtsi b/arch/arm/boot/dts/imx6ull-tarragon-common.dtsi
new file mode 100644
index 000000000000..3fdece5bd31f
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-tarragon-common.dtsi
@@ -0,0 +1,852 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright (C) 2023 chargebyte GmbH
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pwm/pwm.h>
+#include "imx6ull.dtsi"
+
+/ {
+	aliases {
+		mmc0 = &usdhc2; /* eMMC */
+	};
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		pinctrl-0 = <&pinctrl_emmc_rst>;
+		pinctrl-names = "default";
+		reset-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>;
+	};
+
+	reg_dcdc_3v3: regulator-dcdc-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "dcdc-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "ldo-1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_status_leds>;
+
+		led-1 {
+			function = LED_FUNCTION_BOOT;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "timer";
+		};
+
+		led-2 {
+			function = LED_FUNCTION_PROGRAMMING;
+			color = <LED_COLOR_ID_YELLOW>;
+			gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-3 {
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&adc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc_motor
+		     &pinctrl_adc_cp
+		     &pinctrl_adc_pp>;
+	vref-supply = <&vgen1_reg>;
+	status = "okay";
+};
+
+&cpu0 {
+	clock-frequency = <792000000>;
+};
+
+&ecspi2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	num-cs = <3>;
+	cs-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH
+		    &gpio3 2  GPIO_ACTIVE_HIGH
+		    &gpio3 4  GPIO_ACTIVE_HIGH>;
+};
+
+&ecspi4 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi4>;
+	num-cs = <1>;
+	cs-gpios = <&gpio2 15 GPIO_ACTIVE_HIGH>;
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1
+		     &pinctrl_enet1_phy_rst
+		     &pinctrl_enet_mdio>;
+	phy-supply = <&reg_dcdc_3v3>;
+	phy-mode = "rmii";
+	phy-reset-gpios = <&gpio5 6 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <25>;
+	phy-handle = <&ethphy0>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_enet1_phy_int>;
+			interrupt-parent = <&gpio2>;
+			interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+			interrupts-extended = <&gpio2 7 IRQ_TYPE_EDGE_FALLING>;
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			clock-names = "rmii-ref";
+			max-speed = <100>;
+			smsc,disable-energy-detect;
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names = "",				/* 0 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",				/* 5 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",				/* 10 */
+			  "",
+			  "",
+			  "CP_INVERT",
+			  "",
+			  "",				/* 15 */
+			  "",
+			  "",
+			  "",
+			  "MOTOR_1_FAULT_N",
+			  "",				/* 20 */
+			  "",
+			  "ROTARY_SWITCH_1_2_N",
+			  "ROTARY_SWITCH_1_4_N",
+			  "ROTARY_SWITCH_1_8_N",
+			  "MOTOR_2_FAULT_N";		/* 25 */
+};
+
+&gpio3 {
+	gpio-line-names = "",				/* 0 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",				/* 5 */
+			  "EXT_GPIO",
+			  "MOTOR_1_DRIVER_IN1_N",
+			  "MOTOR_1_DRIVER_IN2",
+			  "MOTOR_2_DRIVER_IN1",
+			  "STM32_BOOT0",		/* 10 */
+			  "STM32_RST_N",
+			  "RELAY_1_ENABLE",
+			  "RELAY_2_ENABLE",
+			  "",
+			  "",				/* 15 */
+			  "QCA700X_MAINS_BOOTLOADER_N",
+			  "QCA700X_CP_RST_N",
+			  "QCA700X_CP_BOOTLOADER_N",
+			  "",
+			  "DIGITAL_OUT_1",		/* 20 */
+			  "DIGITAL_OUT_2",
+			  "DIGITAL_OUT_3",
+			  "DIGITAL_OUT_4",
+			  "DIGITAL_OUT_5",
+			  "DIGITAL_OUT_6",		/* 25 */
+			  "ROTARY_SWITCH_2_8_N",
+			  "ROTARY_SWITCH_2_4_N",
+			  "ROTARY_SWITCH_2_2_N";
+};
+
+&gpio4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pmic>;
+
+	gpio-line-names = "",				/* 0 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",				/* 5 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",				/* 10 */
+			  "",
+			  "",
+			  "BOARD_VARIANT_1",
+			  "BOARD_VARIANT_2",
+			  "BOARD_VARIANT_0",		/* 15 */
+			  "BOARD_VARIANT_3",
+			  "",
+			  "ROTARY_SWITCH_2_1_N",
+			  "",
+			  "DIGITAL_IN_5",		/* 20 */
+			  "",
+			  "",
+			  "DIGITAL_IN_6",
+			  "",
+			  "DIGITAL_IN_1",		/* 25 */
+			  "DIGITAL_IN_2",
+			  "DIGITAL_IN_4",
+			  "DIGITAL_IN_3";
+
+	pmic-int-hog {
+		gpio-hog;
+		gpios = <19 0>;
+		input;
+	};
+};
+
+&gpio5 {
+	gpio-line-names = "ROTARY_SWITCH_1_1_N",	/* 0 */
+			  "",
+			  "RELAY_2_SENSE",
+			  "RELAY_1_SENSE",
+			  "",
+			  "",				/* 5 */
+			  "",
+			  "QCA700X_MAINS_RST_N",
+			  "MOTOR_2_DRIVER_IN2",
+			  "",
+			  "CP_POSITIVE_PEAK_RST",	/* 10 */
+			  "CP_NEGATIVE_PEAK_RST";
+};
+
+&i2c4 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	pinctrl-1 = <&pinctrl_i2c4_gpio>;
+	scl-gpios = <&gpio1 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio1 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	pfuze3001: pmic@8 {
+		compatible = "fsl,pfuze3001";
+		reg = <0x08>;
+
+		regulators {
+			sw1_reg: sw1 {
+				regulator-name = "SW1";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw2_reg: sw2 {
+				regulator-name = "SW2";
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3_reg: sw3 {
+				regulator-name = "SW3";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1650000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-name = "VSNVS";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vldo1 {
+				regulator-name = "VLDO1";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen2_reg: vldo2 {
+				regulator-name = "VLDO2";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+				regulator-always-on;
+			};
+
+			vgen3_reg: vccsd {
+				regulator-name = "VCCSD";
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen4_reg: v33 {
+				regulator-name = "V33";
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vldo3 {
+				regulator-name = "VLDO3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vldo4 {
+				regulator-name = "VLDO4";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+
+	onewire@18 {
+		compatible = "maxim,ds2484";
+		reg = <0x18>;
+	};
+
+	accelerometer@19 {
+		compatible = "st,iis328dq", "st,h3lis331dl-accel";
+		reg = <0x19>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_accelerometer_int1_snvs>;
+		vdd-supply = <&reg_dcdc_3v3>;
+		vddio-supply = <&reg_dcdc_3v3>;
+		st,drdy-int-pin = <1>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <5 IRQ_TYPE_EDGE_RISING>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_board_var
+		     &pinctrl_digital_input
+		     &pinctrl_digital_output
+		     &pinctrl_gpio_motor
+		     &pinctrl_hog_pins
+		     &pinctrl_rotary_switch1
+		     &pinctrl_rotary_switch2>;
+
+	pinctrl_adc_cp: adc-cpgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02            0xb0
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03            0xb0
+		>;
+	};
+
+	pinctrl_adc_motor: adc-motorgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__GPIO1_IO00            0xb0
+			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01            0xb0
+			MX6UL_PAD_GPIO1_IO04__GPIO1_IO04            0xb0
+		>;
+	};
+
+	pinctrl_adc_pp: adc-ppgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO05__GPIO1_IO05            0xb0
+		>;
+	};
+
+	pinctrl_board_var: board-vargrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_CLE__GPIO4_IO15              0xb0
+			MX6UL_PAD_NAND_CE0_B__GPIO4_IO13            0xb0
+			MX6UL_PAD_NAND_CE1_B__GPIO4_IO14            0xb0
+			MX6UL_PAD_NAND_DQS__GPIO4_IO16              0xb0
+		>;
+	};
+
+	pinctrl_digital_input: digital-inputgrp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA04__GPIO4_IO25            0xb0
+			MX6UL_PAD_CSI_DATA05__GPIO4_IO26            0xb0
+			MX6UL_PAD_CSI_DATA07__GPIO4_IO28            0xb0
+			MX6UL_PAD_CSI_DATA06__GPIO4_IO27            0xb0
+			MX6UL_PAD_CSI_HSYNC__GPIO4_IO20             0xb0
+			MX6UL_PAD_CSI_DATA02__GPIO4_IO23            0xb0
+		>;
+	};
+
+	pinctrl_digital_output: digital-outputgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA15__GPIO3_IO20            0x400000b0
+			MX6UL_PAD_LCD_DATA16__GPIO3_IO21            0x400000b0
+			MX6UL_PAD_LCD_DATA17__GPIO3_IO22            0x400000b0
+			MX6UL_PAD_LCD_DATA18__GPIO3_IO23            0x400000b0
+			MX6UL_PAD_LCD_DATA19__GPIO3_IO24            0x400000b0
+			MX6UL_PAD_LCD_DATA20__GPIO3_IO25            0x400000b0
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29         0x10b0
+			MX6UL_PAD_LCD_HSYNC__GPIO3_IO02             0xb0
+			MX6UL_PAD_LCD_RESET__GPIO3_IO04             0xb0
+			MX6UL_PAD_UART4_TX_DATA__ECSPI2_SCLK        0x10b0
+			MX6UL_PAD_UART5_RX_DATA__ECSPI2_MISO        0x10b0
+			MX6UL_PAD_UART5_TX_DATA__ECSPI2_MOSI        0x10b0
+		>;
+	};
+
+	pinctrl_ecspi4: ecspi4grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15           0x10b0
+			MX6UL_PAD_ENET2_TX_DATA1__ECSPI4_SCLK       0x10b0
+			MX6UL_PAD_ENET2_TX_CLK__ECSPI4_MISO         0x10b0
+			MX6UL_PAD_ENET2_TX_EN__ECSPI4_MOSI          0x10b0
+		>;
+	};
+
+	pinctrl_emmc_rst: emmc-rstgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10              0x400010b0
+		>;
+	};
+
+	pinctrl_enet_mdio: enet-mdiogrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO            0x10b0
+			MX6UL_PAD_GPIO1_IO07__ENET1_MDC             0x10b0
+		>;
+	};
+
+	pinctrl_enet1_phy_int: enet1-phy-intgrp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_ER__GPIO2_IO07           0x10b0
+		>;
+	};
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00     0x100b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01     0x100b0
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN          0x100b0
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1      0x400000b1
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00     0xb0
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01     0xb0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN          0xb0
+		>;
+	};
+
+	pinctrl_ext_uart: ext-uartgrp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_TX_DATA0__UART7_DCE_RX      0xb0
+			MX6UL_PAD_ENET2_RX_EN__UART7_DCE_TX         0xb0
+		>;
+	};
+
+	pinctrl_fan_enable: fan-enablegrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA00__GPIO3_IO05            0x400000b0
+		>;
+	};
+
+	pinctrl_gpio_motor: gpio-motorgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA02__GPIO3_IO07            0x400000b0
+			MX6UL_PAD_LCD_DATA03__GPIO3_IO08            0x400000b0
+			MX6UL_PAD_LCD_DATA04__GPIO3_IO09            0x400000b0
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19           0xb0
+			MX6UL_PAD_UART3_RX_DATA__GPIO1_IO25         0xb0
+		>;
+	};
+
+	pinctrl_hog_pins: hog-pinsgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA07__GPIO3_IO12            0x400000b0
+			MX6UL_PAD_LCD_DATA08__GPIO3_IO13            0x400000b0
+			MX6UL_PAD_JTAG_TDI__GPIO1_IO13              0x400070a0
+			MX6UL_PAD_LCD_DATA05__GPIO3_IO10            0x400000b0
+			MX6UL_PAD_LCD_DATA06__GPIO3_IO11            0x400000b0
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_RX_DATA__I2C4_SDA           0x400008b0
+			MX6UL_PAD_UART2_TX_DATA__I2C4_SCL           0x400008b0
+		>;
+	};
+
+	pinctrl_i2c4_gpio: i2c4-gpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_RX_DATA__GPIO1_IO21         0x400008b0
+			MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20         0x400008b0
+		>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO08__USDHC2_VSELECT        0x70b1
+			MX6UL_PAD_CSI_VSYNC__GPIO4_IO19             0xb0
+		>;
+	};
+
+	pinctrl_pwm_cp: pinctrl-pwm-cpgrp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TRST_B__PWM8_OUT             0x60a0
+		>;
+	};
+
+	pinctrl_pwm_digital_input_ref: pwm-digital-input-refgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO09__PWM2_OUT              0xb0
+		>;
+	};
+
+	pinctrl_pwm_fan: pwm-fangrp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TCK__PWM7_OUT                0x60a0
+		>;
+	};
+
+	pinctrl_qca700x_cp_btld: qca700x-cp-btldgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA13__GPIO3_IO18            0x400000b0
+		>;
+	};
+
+	pinctrl_qca700x_cp_int: qca700x-cp-intgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_DATA1__GPIO2_IO19             0x10b0
+		>;
+	};
+
+	pinctrl_qca700x_cp_rst: qca700x-cp-rstgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA12__GPIO3_IO17            0x400000b0
+		>;
+	};
+
+	pinctrl_qca700x_mains_btld: qca700x-mains-btldgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA11__GPIO3_IO16            0x400000b0
+		>;
+	};
+
+	pinctrl_rotary_switch1: rotary-switch1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_CTS_B__GPIO1_IO22           0xb0
+			MX6UL_PAD_UART2_RTS_B__GPIO1_IO23           0xb0
+			MX6UL_PAD_UART3_TX_DATA__GPIO1_IO24         0xb0
+		>;
+	};
+
+	pinctrl_rotary_switch2: rotary-switch2grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_PIXCLK__GPIO4_IO18            0xb0
+			MX6UL_PAD_LCD_DATA23__GPIO3_IO28            0xb0
+			MX6UL_PAD_LCD_DATA22__GPIO3_IO27            0xb0
+			MX6UL_PAD_LCD_DATA21__GPIO3_IO26            0xb0
+		>;
+	};
+
+	pinctrl_rs485_1: rs485-1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18           0xb0
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX       0xb0
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX       0xb0
+		>;
+	};
+
+	pinctrl_rs485_2: rs485-2grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA03__GPIO4_IO24            0x10b0
+			MX6UL_PAD_CSI_DATA01__UART5_DCE_RX          0x10b0
+			MX6UL_PAD_CSI_DATA00__UART5_DCE_TX          0x10b0
+		>;
+	};
+
+	pinctrl_status_leds: status-ledsgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA09__GPIO3_IO14            0xb0
+			MX6UL_PAD_LCD_DATA10__GPIO3_IO15            0xb0
+			MX6UL_PAD_LCD_DATA14__GPIO3_IO19            0xb0
+		>;
+	};
+
+	pinctrl_stm32: stm32grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_RX_DATA1__UART6_DCE_RX      0x10b0
+			MX6UL_PAD_ENET2_RX_DATA0__UART6_DCE_TX      0x10b0
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_CLK__UART4_DTE_RX             0xb0
+			MX6UL_PAD_LCD_ENABLE__UART4_DTE_TX          0xb0
+		>;
+	};
+
+	pinctrl_usb: usbgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CLK__USB_OTG1_OC              0x70b0
+			MX6UL_PAD_SD1_DATA0__ANATOP_OTG1_ID         0x70b0
+		>;
+	};
+
+	pinctrl_usb_pwr: usb-pwrgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USB_OTG1_PWR             0xb0
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK             0x7071
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD             0x7071
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0         0x7071
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1         0x7071
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2         0x7071
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3         0x7071
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4         0x7071
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5         0x7071
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6         0x7071
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7         0x7071
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK             0x70b1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD             0x70b1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0         0x70b1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1         0x70b1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2         0x70b1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3         0x70b1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4         0x70b1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5         0x70b1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6         0x70b1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7         0x70b1
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK             0x70f1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD             0x70f1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0         0x70f1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1         0x70f1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2         0x70f1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3         0x70f1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4         0x70f1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5         0x70f1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6         0x70f1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7         0x70f1
+		>;
+	};
+
+	pinctrl_wdog2: wdoggrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_VSYNC__WDOG2_WDOG_B           0x10b0
+		>;
+	};
+};
+
+&iomuxc_snvs {
+	pinctrl-names = "default_snvs";
+	pinctrl-0 = <&pinctrl_cp_peak_snvs
+		     &pinctrl_gpio_motor_snvs
+		     &pinctrl_relay_sense_snvs
+		     &pinctrl_rotary_switch1_snvs>;
+
+	pinctrl_accelerometer_int1_snvs: accelerometer-int1-snvsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05         0x130a0
+		>;
+	};
+
+	pinctrl_cp_peak_snvs: cp-peak-snvsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_BOOT_MODE0__GPIO5_IO10           0x130a0
+			MX6ULL_PAD_BOOT_MODE1__GPIO5_IO11           0x130a0
+		>;
+	};
+
+	pinctrl_enet1_phy_rst: enet1-phy-rstgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06         0x100a0
+		>;
+	};
+
+	pinctrl_fan_sense_snvs: fan-sense-snvsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01         0x100a0
+		>;
+	};
+
+	pinctrl_gpio_motor_snvs: gpio-motor-snvsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER8__GPIO5_IO08         0x110a0
+		>;
+	};
+
+	pinctrl_qca700x_mains_int: qca700x-mains-intgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09         0x130a0
+		>;
+	};
+
+	pinctrl_qca700x_mains_rst: qca700x-mains-rstgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER7__GPIO5_IO07         0x400100a0
+		>;
+	};
+
+	pinctrl_relay_sense_snvs: relay-sense-snvsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03         0x100a0
+			MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02         0x100a0
+		>;
+	};
+
+	pinctrl_rotary_switch1_snvs: rotary-switch1-snvsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00         0x110a0
+		>;
+	};
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_digital_input_ref>;
+	status = "okay";
+};
+
+&pwm8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_cp>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rs485_1>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	fsl,dte-mode;
+	status = "okay";
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rs485_2>;
+};
+
+&uart6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_stm32>;
+	status = "okay";
+};
+
+&uart7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ext_uart>;
+	status = "okay";
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb
+		     &pinctrl_usb_pwr>;
+	dr_mode = "host";
+	power-active-high;
+	disable-over-current;
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&usbphy1 {
+	fsl,tx-cal-45-dn-ohms = <35>;
+	fsl,tx-cal-45-dp-ohms = <35>;
+};
+
+&usbphy2 {
+	fsl,tx-cal-45-dn-ohms = <35>;
+	fsl,tx-cal-45-dp-ohms = <35>;
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	vmmc-supply = <&sw2_reg>;
+	vqmmc-supply = <&reg_1v8>;
+	mmc-pwrseq = <&emmc_pwrseq>;
+	bus-width = <8>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
+&wdog1 {
+	status = "disabled";
+};
+
+&wdog2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog2>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ull-tarragon-master.dts b/arch/arm/boot/dts/imx6ull-tarragon-master.dts
new file mode 100644
index 000000000000..67007ce383e3
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-tarragon-master.dts
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright (C) 2023 chargebyte GmbH
+
+#include "imx6ull-tarragon-common.dtsi"
+
+/ {
+	model = "chargebyte Tarragon Master";
+	compatible = "chargebyte,imx6ull-tarragon-master", "fsl,imx6ull";
+
+	fan0: pwm-fan {
+		compatible = "pwm-fan";
+		pwms = <&pwm7 0 40000 PWM_POLARITY_INVERTED>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_fan_sense_snvs>;
+		fan-supply = <&reg_fan>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+	reg_fan: regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "fan-supply";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_fan_enable>;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+};
+
+&ecspi2 {
+	status = "okay";
+
+	qca700x_cp: ethernet@0 {
+		reg = <0x0>;
+		compatible = "qca,qca7000";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_qca700x_cp_int
+			     &pinctrl_qca700x_cp_rst
+			     &pinctrl_qca700x_cp_btld>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <19 IRQ_TYPE_EDGE_RISING>;
+		spi-cpha;
+		spi-cpol;
+		spi-max-frequency = <16000000>;
+	};
+};
+
+&ecspi4 {
+	status = "okay";
+
+	qca700x_mains: ethernet@0 {
+		reg = <0x0>;
+		compatible = "qca,qca7000";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_qca700x_mains_int
+			     &pinctrl_qca700x_mains_rst
+			     &pinctrl_qca700x_mains_btld>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <9 IRQ_TYPE_EDGE_RISING>;
+		spi-cpha;
+		spi-cpol;
+		spi-max-frequency = <16000000>;
+	};
+};
+
+&fec1 {
+	status = "okay";
+};
+
+&pwm7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_fan>;
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ull-tarragon-micro.dts b/arch/arm/boot/dts/imx6ull-tarragon-micro.dts
new file mode 100644
index 000000000000..e471c2005bee
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-tarragon-micro.dts
@@ -0,0 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright (C) 2023 chargebyte GmbH
+
+#include "imx6ull-tarragon-common.dtsi"
+
+/ {
+	model = "chargebyte Tarragon Micro";
+	compatible = "chargebyte,imx6ull-tarragon-micro", "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/imx6ull-tarragon-slave.dts b/arch/arm/boot/dts/imx6ull-tarragon-slave.dts
new file mode 100644
index 000000000000..cee223b5f8e1
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-tarragon-slave.dts
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright (C) 2023 chargebyte GmbH
+
+#include "imx6ull-tarragon-common.dtsi"
+
+/ {
+	model = "chargebyte Tarragon Slave";
+	compatible = "chargebyte,imx6ull-tarragon-slave", "fsl,imx6ull";
+};
+
+&ecspi2 {
+	status = "okay";
+
+	qca700x_cp: ethernet@0 {
+		reg = <0x0>;
+		compatible = "qca,qca7000";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_qca700x_cp_int
+			     &pinctrl_qca700x_cp_rst
+			     &pinctrl_qca700x_cp_btld>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <19 IRQ_TYPE_EDGE_RISING>;
+		spi-cpha;
+		spi-cpol;
+		spi-max-frequency = <16000000>;
+	};
+};
+
+&fec1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ull-tarragon-slavext.dts b/arch/arm/boot/dts/imx6ull-tarragon-slavext.dts
new file mode 100644
index 000000000000..7fd53b7a4372
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-tarragon-slavext.dts
@@ -0,0 +1,64 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright (C) 2023 chargebyte GmbH
+
+#include "imx6ull-tarragon-common.dtsi"
+
+/ {
+	model = "chargebyte Tarragon SlaveXT";
+	compatible = "chargebyte,imx6ull-tarragon-slavext", "fsl,imx6ull";
+
+	fan0: pwm-fan {
+		compatible = "pwm-fan";
+		pwms = <&pwm7 0 40000 PWM_POLARITY_INVERTED>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_fan_sense_snvs>;
+		fan-supply = <&reg_fan>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+	reg_fan: regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "fan-supply";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_fan_enable>;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+};
+
+&ecspi2 {
+	status = "okay";
+
+	qca700x_cp: ethernet@0 {
+		reg = <0x0>;
+		compatible = "qca,qca7000";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_qca700x_cp_int
+			     &pinctrl_qca700x_cp_rst
+			     &pinctrl_qca700x_cp_btld>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <19 IRQ_TYPE_EDGE_RISING>;
+		spi-cpha;
+		spi-cpol;
+		spi-max-frequency = <16000000>;
+	};
+};
+
+&fec1 {
+	status = "okay";
+};
+
+&pwm7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_fan>;
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
-- 
2.17.1

[PATCH V4 6/6] ARM: imx_v6_v7_defconfig: Enable Tarragon peripheral drivers

[Stefan Wahren]

We need to enable some drivers in order to use the following peripherals
of Tarragon:
  * QCA7000/7005 Powerline chip
  * One-Wire Master DS2484 with external thermal sensors
  * external 4 pin PWM fan
  * ST IIS328DQ I2C accelerometer

Signed-off-by: Stefan Wahren <stefan.wahren@chargebyte.com>
---
 arch/arm/configs/imx_v6_v7_defconfig | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm/configs/imx_v6_v7_defconfig b/arch/arm/configs/imx_v6_v7_defconfig
index 9475839e7fe1..2e2af31eeb4c 100644
--- a/arch/arm/configs/imx_v6_v7_defconfig
+++ b/arch/arm/configs/imx_v6_v7_defconfig
@@ -128,6 +128,7 @@ CONFIG_CS89x0_PLATFORM=y
 # CONFIG_NET_VENDOR_MICREL is not set
 # CONFIG_NET_VENDOR_MICROCHIP is not set
 # CONFIG_NET_VENDOR_NATSEMI is not set
+CONFIG_QCA7000_SPI=m
 # CONFIG_NET_VENDOR_SEEQ is not set
 CONFIG_SMC91X=y
 CONFIG_SMC911X=y
@@ -216,6 +217,9 @@ CONFIG_GPIO_PCF857X=y
 CONFIG_GPIO_BD71815=y
 CONFIG_GPIO_STMPE=y
 CONFIG_GPIO_74X164=y
+CONFIG_W1=m
+CONFIG_W1_MASTER_DS2482=m
+CONFIG_W1_SLAVE_THERM=m
 CONFIG_POWER_RESET=y
 CONFIG_POWER_RESET_SYSCON=y
 CONFIG_POWER_RESET_SYSCON_POWEROFF=y
@@ -224,6 +228,7 @@ CONFIG_RN5T618_POWER=m
 CONFIG_SENSORS_MC13783_ADC=y
 CONFIG_SENSORS_GPIO_FAN=y
 CONFIG_SENSORS_IIO_HWMON=y
+CONFIG_SENSORS_PWM_FAN=y
 CONFIG_SENSORS_SY7636A=y
 CONFIG_THERMAL_STATISTICS=y
 CONFIG_THERMAL_WRITABLE_TRIPS=y
@@ -409,6 +414,7 @@ CONFIG_CLK_IMX8MQ=y
 CONFIG_SOC_IMX8M=y
 CONFIG_EXTCON_USB_GPIO=y
 CONFIG_IIO=y
+CONFIG_IIO_ST_ACCEL_3AXIS=m
 CONFIG_MMA8452=y
 CONFIG_IMX7D_ADC=y
 CONFIG_RN5T618_ADC=y
-- 
2.17.1

Re: [PATCH V4 2/6] dt-bindings: w1: Add DS2482/DS2484 I2C to 1-W bridges

[Krzysztof Kozlowski]

On 31/03/2023 23:08, Stefan Wahren wrote:
> Even this binding look trivial, the actual hardware supports more
> features (e.g. sleep mode control GPIO). So add this as a dedicated
> devicetree binding for the Maxim DS2482/DS2484 I2C to 1-W bridges,
> which can be extended later.
> 
> Signed-off-by: Stefan Wahren <stefan.wahren@chargebyte.com>
> ---
>  .../devicetree/bindings/w1/maxim,ds2482.yaml  | 43 +++++++++++++++++++
>  1 file changed, 43 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/w1/maxim,ds2482.yaml
> 
> diff --git a/Documentation/devicetree/bindings/w1/maxim,ds2482.yaml b/Documentation/devicetree/bindings/w1/maxim,ds2482.yaml
> new file mode 100644
> index 000000000000..fd692a3a7400
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/w1/maxim,ds2482.yaml
> @@ -0,0 +1,43 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---

This is still incomplete as it does not allow children, but you
mentioned it in commit msg and other two bindings are limited as well,
so sounds ok:

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

Re: [PATCH V4 2/6] dt-bindings: w1: Add DS2482/DS2484 I2C to 1-W bridges

[Rob Herring]

On Fri, Mar 31, 2023 at 11:08:36PM +0200, Stefan Wahren wrote:
> Even this binding look trivial, the actual hardware supports more
> features (e.g. sleep mode control GPIO). So add this as a dedicated
> devicetree binding for the Maxim DS2482/DS2484 I2C to 1-W bridges,
> which can be extended later.
> 
> Signed-off-by: Stefan Wahren <stefan.wahren@chargebyte.com>
> ---
>  .../devicetree/bindings/w1/maxim,ds2482.yaml  | 43 +++++++++++++++++++
>  1 file changed, 43 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/w1/maxim,ds2482.yaml
> 
> diff --git a/Documentation/devicetree/bindings/w1/maxim,ds2482.yaml b/Documentation/devicetree/bindings/w1/maxim,ds2482.yaml
> new file mode 100644
> index 000000000000..fd692a3a7400
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/w1/maxim,ds2482.yaml
> @@ -0,0 +1,43 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/w1/maxim,ds2482.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Maxim One wire bus master controller
> +
> +maintainers:
> +  - Stefan Wahren <stefan.wahren@chargebyte.com>
> +
> +description: |
> +  I2C to 1-wire bridges
> +
> +  https://www.analog.com/media/en/technical-documentation/data-sheets/ds2482-100.pdf
> +  https://www.analog.com/media/en/technical-documentation/data-sheets/DS2482-800.pdf
> +  https://www.analog.com/media/en/technical-documentation/data-sheets/DS2484.pdf
> +
> +properties:
> +  compatible:
> +    enum:
> +      - maxim,ds2482
> +      - maxim,ds2484
> +
> +  reg:
> +    maxItems: 1
> +
> +required:
> +  - compatible
> +  - reg
> +
> +additionalProperties: false

To allow children, all that's needed for 1-wire is:

additionalProperties:
  type: object

> +
> +examples:
> +  - |
> +    i2c {
> +      #address-cells = <1>;
> +      #size-cells = <0>;
> +      onewire@18 {
> +        compatible = "maxim,ds2484";
> +        reg = <0x18>;
> +      };
> +    };
> -- 
> 2.17.1
>