* [PATCH v8 0/3] Initial support for Qualcomm Hamoa IOT EVK board
@ 2025-08-28 4:48 Yijie Yang
2025-08-28 4:48 ` [PATCH v8 1/3] dt-bindings: arm: qcom: Document HAMOA-IOT-EVK board Yijie Yang
` (2 more replies)
0 siblings, 3 replies; 13+ messages in thread
From: Yijie Yang @ 2025-08-28 4:48 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, Yijie Yang,
Krzysztof Kozlowski, Konrad Dybcio
Introduce the device tree, DT bindings, and driver modifications required
to bring up the HAMOA-IOT-EVK evaluation board—based on the X1E80100 SoC—to
a UART shell.
This patch set focuses on two key hardware components: the HAMOA-IOT-SOM
and the HAMOA-IOT-EVK carrier board.
The HAMOA-IOT-SOM is a compact System on Module that integrates the SoC,
GPIOs, and PMICs. It is designed to be modular and can be paired with
various carrier boards to support different use cases.
The HAMOA-IOT-EVK is one such carrier board, designed for IoT scenarios.
It provides essential peripherals such as UART, on-board PMICs, and
USB-related components.
Together, these components form a flexible and scalable platform, and this
patch set enables their initial bring-up through proper device tree
configuration and driver support.
Qualcomm SoCs often have multiple product variants, each identified by a
different SoC ID. For instance, the x1e80100 SoC has closely related
variants such as x1e78100 and x1e001de. This diversity in SoC identifiers
can lead to confusion and unnecessary maintenance complexity in the device
tree and related subsystems.
To address this, code names offer a more consistent and project-agnostic
way to represent SoC families. They tend to remain stable across
development efforts.
This patch series introduces "hamoa" as the codename for the x1e80100 SoC.
Going forward, all x1e80100-related variants—including x1e81000 and others
in the same family—will be represented under the "hamoa" designation in the
device tree.
This improves readability, streamlines future maintenance, and aligns with
common naming practices across Qualcomm-based platforms.
Features added and enabled:
- UART
- On-board regulators
- Regulators on the SOM
- PMIC GLINK
- USB0 through USB6 and their PHYs
- Embedded USB (eUSB) repeaters
- USB Type-C mux
- PCIe6a and its PHY
- PCIe4 and its PHY
- Reserved memory regions
- Pinctrl
- NVMe
- ADSP, CDSP
- WLAN, Bluetooth (M.2 interface)
- USB DisplayPort
- Graphic
- Audio
Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com>
---
Changes in v8:
- Change the style of how collaborators are listed.
- Link to v7: https://lore.kernel.org/r/20250827-hamoa_initial-v7-0-f9b81d564bb2@oss.qualcomm.com
Changes in v7:
- Configure the EDP regulator to boot-on.
- Change back to a year‑less copyright statement.
- Update base commit.
- Link to v6: https://lore.kernel.org/r/20250821-hamoa_initial-v6-0-72e4e01a55d0@oss.qualcomm.com
Changes in v6:
- Restore the full change log for each revision.
- Merge the changes related to Audio and Graphics into the patch series.
- Link to v5: https://lore.kernel.org/r/20250814-hamoa_initial-v5-0-817a9c6e8d47@oss.qualcomm.com
Changes in v5:
- Update base commit.
- Drop an already merged patch:
https://lore.kernel.org/all/20250804-hamoa_initial-v4-2-19edbb28677b@oss.qualcomm.com/
- Link to v4: https://lore.kernel.org/r/20250804-hamoa_initial-v4-0-19edbb28677b@oss.qualcomm.com
Changes in v4:
- Update commit messages.
- Update base commit.
- Update the format of the node mdss_dp3_out.
- Add comments to clarify certain nodes.
- Update the configuration of regulator-wcn-3p3 from regulator-boot-on to regulator-always-on.
- Link to v3: https://lore.kernel.org/r/20250729-hamoa_initial-v3-0-806e092789dc@oss.qualcomm.com
Changes in v3:
- Add compatible string and dt-bindings for SOM.
- Restore PMU-related regulators to comply with dt-binding rules and enable kernel-level power management.
- Adjust commit description accordingly.
- Link to v2: https://lore.kernel.org/r/20250724-hamoa_initial-v2-0-91b00c882d11@oss.qualcomm.com
Changes in v2:
- Merge the compatible rules and remove the compatible string map.
- Align the ADSP and CDSP firmware paths with other x1e80100 platforms.
- Remove the regulators on the M.2 card, as well as those managed by UEFI on this board.
- Merge another patch series that enables USB DisplayPort functionality on this platform: https://lore.kernel.org/all/20250723-x1e-evk-dp-v1-1-be76ce53b9b8@quicinc.com/
- Link to v1: https://lore.kernel.org/r/20250716-hamoa_initial-v1-0-f6f5d0f9a163@oss.qualcomm.com
---
Yijie Yang (3):
dt-bindings: arm: qcom: Document HAMOA-IOT-EVK board
arm64: dts: qcom: Add HAMOA-IOT-SOM platform
arm64: dts: qcom: Add base HAMOA-IOT-EVK board
Documentation/devicetree/bindings/arm/qcom.yaml | 6 +
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts | 1247 +++++++++++++++++++++++
arch/arm64/boot/dts/qcom/hamoa-iot-som.dtsi | 609 +++++++++++
4 files changed, 1863 insertions(+)
---
base-commit: b899981540841e409e496083921f2e5c4c209925
change-id: 20250604-hamoa_initial-0cd7036d7271
Best regards,
--
Yijie Yang <yijie.yang@oss.qualcomm.com>
^ permalink raw reply [flat|nested] 13+ messages in thread* [PATCH v8 1/3] dt-bindings: arm: qcom: Document HAMOA-IOT-EVK board 2025-08-28 4:48 [PATCH v8 0/3] Initial support for Qualcomm Hamoa IOT EVK board Yijie Yang @ 2025-08-28 4:48 ` Yijie Yang 2025-08-28 4:48 ` [PATCH v8 2/3] arm64: dts: qcom: Add HAMOA-IOT-SOM platform Yijie Yang 2025-08-28 4:48 ` [PATCH v8 3/3] arm64: dts: qcom: Add base HAMOA-IOT-EVK board Yijie Yang 2 siblings, 0 replies; 13+ messages in thread From: Yijie Yang @ 2025-08-28 4:48 UTC (permalink / raw) To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley Cc: linux-arm-msm, devicetree, linux-kernel, Yijie Yang, Krzysztof Kozlowski Document the device tree binding for the HAMOA-IOT-EVK board, which uses the Qualcomm X1E80100 SoC. The EVK consists of a carrier board and a modular System-on-Module (SoM). The SoM integrates the SoC, PMICs, and essential GPIOs, while the EVK carrier board provides additional peripherals such as UART and USB interfaces. Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com> --- Documentation/devicetree/bindings/arm/qcom.yaml | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml index 55e5eb75af89..6b6503181ad6 100644 --- a/Documentation/devicetree/bindings/arm/qcom.yaml +++ b/Documentation/devicetree/bindings/arm/qcom.yaml @@ -1069,6 +1069,12 @@ properties: - qcom,x1e80100-qcp - const: qcom,x1e80100 + - items: + - enum: + - qcom,hamoa-iot-evk + - const: qcom,hamoa-iot-som + - const: qcom,x1e80100 + - items: - enum: - asus,zenbook-a14-ux3407qa -- 2.34.1 ^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH v8 2/3] arm64: dts: qcom: Add HAMOA-IOT-SOM platform 2025-08-28 4:48 [PATCH v8 0/3] Initial support for Qualcomm Hamoa IOT EVK board Yijie Yang 2025-08-28 4:48 ` [PATCH v8 1/3] dt-bindings: arm: qcom: Document HAMOA-IOT-EVK board Yijie Yang @ 2025-08-28 4:48 ` Yijie Yang 2025-08-28 4:48 ` [PATCH v8 3/3] arm64: dts: qcom: Add base HAMOA-IOT-EVK board Yijie Yang 2 siblings, 0 replies; 13+ messages in thread From: Yijie Yang @ 2025-08-28 4:48 UTC (permalink / raw) To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley Cc: linux-arm-msm, devicetree, linux-kernel, Yijie Yang, Konrad Dybcio The HAMOA-IOT-SOM is a compact computing module that integrates a System on Chip (SoC) — specifically the x1e80100 — along with essential components optimized for IoT applications. It is designed to be mounted on carrier boards, enabling the development of complete embedded systems. This change enables the following components: - Regulators on the SOM - Reserved memory regions - PCIe6a and its PHY - PCIe4 and its PHY - USB0 through USB6 and their PHYs - ADSP, CDSP - WLAN, Bluetooth (M.2 interface) Written in collaboration with Yingying Tang (PCIe4 and WLAN) <quic_yintang@quicinc.com>. Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com> --- arch/arm64/boot/dts/qcom/hamoa-iot-som.dtsi | 609 ++++++++++++++++++++++++++++ 1 file changed, 609 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/hamoa-iot-som.dtsi b/arch/arm64/boot/dts/qcom/hamoa-iot-som.dtsi new file mode 100644 index 000000000000..5facc5544c3d --- /dev/null +++ b/arch/arm64/boot/dts/qcom/hamoa-iot-som.dtsi @@ -0,0 +1,609 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. + */ + +#include "x1e80100.dtsi" +#include "x1e80100-pmics.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> + +/ { + compatible = "hamoa-iot-som", "qcom,x1e80100"; + + reserved-memory { + linux,cma { + compatible = "shared-dma-pool"; + size = <0x0 0x8000000>; + reusable; + linux,cma-default; + }; + }; +}; + +&apps_rsc { + /* PMC8380C_B */ + regulators-0 { + compatible = "qcom,pm8550-rpmh-regulators"; + qcom,pmic-id = "b"; + + vdd-bob1-supply = <&vph_pwr>; + vdd-bob2-supply = <&vph_pwr>; + vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>; + vdd-l2-l13-l14-supply = <&vreg_bob1>; + vdd-l5-l16-supply = <&vreg_bob1>; + vdd-l6-l7-supply = <&vreg_bob2>; + vdd-l8-l9-supply = <&vreg_bob1>; + vdd-l12-supply = <&vreg_s5j_1p2>; + vdd-l15-supply = <&vreg_s4c_1p8>; + vdd-l17-supply = <&vreg_bob2>; + + vreg_bob1: bob1 { + regulator-name = "vreg_bob1"; + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_bob2: bob2 { + regulator-name = "vreg_bob2"; + regulator-min-microvolt = <2504000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1b_1p8: ldo1 { + regulator-name = "vreg_l1b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2b_3p0: ldo2 { + regulator-name = "vreg_l2b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4b_1p8: ldo4 { + regulator-name = "vreg_l4b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5b_3p0: ldo5 { + regulator-name = "vreg_l5b_3p0"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6b_1p8: ldo6 { + regulator-name = "vreg_l6b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7b_2p8: ldo7 { + regulator-name = "vreg_l7b_2p8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8b_3p0: ldo8 { + regulator-name = "vreg_l8b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9b_2p9: ldo9 { + regulator-name = "vreg_l9b_2p9"; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l10b_1p8: ldo10 { + regulator-name = "vreg_l10b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l12b_1p2: ldo12 { + regulator-name = "vreg_l12b_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-always-on; + }; + + vreg_l13b_3p0: ldo13 { + regulator-name = "vreg_l13b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l14b_3p0: ldo14 { + regulator-name = "vreg_l14b_3p0"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l15b_1p8: ldo15 { + regulator-name = "vreg_l15b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-always-on; + }; + + vreg_l16b_2p9: ldo16 { + regulator-name = "vreg_l16b_2p9"; + regulator-min-microvolt = <2912000>; + regulator-max-microvolt = <2912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l17b_2p5: ldo17 { + regulator-name = "vreg_l17b_2p5"; + regulator-min-microvolt = <2504000>; + regulator-max-microvolt = <2504000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + /* PMC8380VE_C */ + regulators-1 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + qcom,pmic-id = "c"; + + vdd-l1-supply = <&vreg_s5j_1p2>; + vdd-l2-supply = <&vreg_s1f_0p7>; + vdd-l3-supply = <&vreg_s1f_0p7>; + vdd-s4-supply = <&vph_pwr>; + + vreg_s4c_1p8: smps4 { + regulator-name = "vreg_s4c_1p8"; + regulator-min-microvolt = <1856000>; + regulator-max-microvolt = <2000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1c_1p2: ldo1 { + regulator-name = "vreg_l1c_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2c_0p8: ldo2 { + regulator-name = "vreg_l2c_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3c_0p8: ldo3 { + regulator-name = "vreg_l3c_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + /* PMC8380_D */ + regulators-2 { + compatible = "qcom,pmc8380-rpmh-regulators"; + qcom,pmic-id = "d"; + + vdd-l1-supply = <&vreg_s1f_0p7>; + vdd-l2-supply = <&vreg_s1f_0p7>; + vdd-l3-supply = <&vreg_s4c_1p8>; + vdd-s1-supply = <&vph_pwr>; + + vreg_l1d_0p8: ldo1 { + regulator-name = "vreg_l1d_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2d_0p9: ldo2 { + regulator-name = "vreg_l2d_0p9"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3d_1p8: ldo3 { + regulator-name = "vreg_l3d_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + /* PMC8380_E */ + regulators-3 { + compatible = "qcom,pmc8380-rpmh-regulators"; + qcom,pmic-id = "e"; + + vdd-l2-supply = <&vreg_s1f_0p7>; + vdd-l3-supply = <&vreg_s5j_1p2>; + + vreg_l2e_0p8: ldo2 { + regulator-name = "vreg_l2e_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3e_1p2: ldo3 { + regulator-name = "vreg_l3e_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + /* PMC8380_F */ + regulators-4 { + compatible = "qcom,pmc8380-rpmh-regulators"; + qcom,pmic-id = "f"; + + vdd-l1-supply = <&vreg_s5j_1p2>; + vdd-l2-supply = <&vreg_s5j_1p2>; + vdd-l3-supply = <&vreg_s5j_1p2>; + vdd-s1-supply = <&vph_pwr>; + + vreg_s1f_0p7: smps1 { + regulator-name = "vreg_s1f_0p7"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1f_1p0: ldo1 { + regulator-name = "vreg_l1f_1p0"; + regulator-min-microvolt = <1024000>; + regulator-max-microvolt = <1024000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2f_1p0: ldo2 { + regulator-name = "vreg_l2f_1p0"; + regulator-min-microvolt = <1024000>; + regulator-max-microvolt = <1024000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3f_1p0: ldo3 { + regulator-name = "vreg_l3f_1p0"; + regulator-min-microvolt = <1024000>; + regulator-max-microvolt = <1024000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + /* PMC8380VE_I */ + regulators-6 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + qcom,pmic-id = "i"; + + vdd-l1-supply = <&vreg_s4c_1p8>; + vdd-l2-supply = <&vreg_s5j_1p2>; + vdd-l3-supply = <&vreg_s1f_0p7>; + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + + vreg_s1i_0p9: smps1 { + regulator-name = "vreg_s1i_0p9"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s2i_1p0: smps2 { + regulator-name = "vreg_s2i_1p0"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1100000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1i_1p8: ldo1 { + regulator-name = "vreg_l1i_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2i_1p2: ldo2 { + regulator-name = "vreg_l2i_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3i_0p8: ldo3 { + regulator-name = "vreg_l3i_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + /* PMC8380VE_J */ + regulators-7 { + compatible = "qcom,pm8550ve-rpmh-regulators"; + qcom,pmic-id = "j"; + + vdd-l1-supply = <&vreg_s1f_0p7>; + vdd-l2-supply = <&vreg_s5j_1p2>; + vdd-l3-supply = <&vreg_s1f_0p7>; + vdd-s5-supply = <&vph_pwr>; + + vreg_s5j_1p2: smps5 { + regulator-name = "vreg_s5j_1p2"; + regulator-min-microvolt = <1256000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1j_0p8: ldo1 { + regulator-name = "vreg_l1j_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2j_1p2: ldo2 { + regulator-name = "vreg_l2j_1p2"; + regulator-min-microvolt = <1256000>; + regulator-max-microvolt = <1256000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3j_0p8: ldo3 { + regulator-name = "vreg_l3j_0p8"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; +}; + +&pcie4 { + perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>; + wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>; + + pinctrl-0 = <&pcie4_default>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&pcie4_phy { + vdda-phy-supply = <&vreg_l3i_0p8>; + vdda-pll-supply = <&vreg_l3e_1p2>; + + status = "okay"; +}; + +&pcie6a { + perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>; + wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>; + + pinctrl-0 = <&pcie6a_default>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&pcie6a_phy { + vdda-phy-supply = <&vreg_l1d_0p8>; + vdda-pll-supply = <&vreg_l2j_1p2>; + + status = "okay"; +}; + +&qupv3_0 { + status = "okay"; +}; + +&qupv3_1 { + status = "okay"; +}; + +&qupv3_2 { + status = "okay"; +}; + +&remoteproc_adsp { + firmware-name = "qcom/x1e80100/adsp.mbn", + "qcom/x1e80100/adsp_dtb.mbn"; + + status = "okay"; +}; + +&remoteproc_cdsp { + firmware-name = "qcom/x1e80100/cdsp.mbn", + "qcom/x1e80100/cdsp_dtb.mbn"; + + status = "okay"; +}; + +&tlmm { + gpio-reserved-ranges = <34 2>, /* TPM LP & INT */ + <44 4>; /* SPI (TPM) */ + + pcie4_default: pcie4-default-state { + clkreq-n-pins { + pins = "gpio147"; + function = "pcie4_clk"; + drive-strength = <2>; + bias-pull-up; + }; + + perst-n-pins { + pins = "gpio146"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + wake-n-pins { + pins = "gpio148"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + pcie6a_default: pcie6a-default-state { + clkreq-n-pins { + pins = "gpio153"; + function = "pcie6a_clk"; + drive-strength = <2>; + bias-pull-up; + }; + + perst-n-pins { + pins = "gpio152"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + wake-n-pins { + pins = "gpio154"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + + }; + }; +}; + +&usb_1_ss0 { + status = "okay"; +}; + +&usb_1_ss0_dwc3 { + dr_mode = "otg"; + usb-role-switch; +}; + +&usb_1_ss0_hsphy { + vdd-supply = <&vreg_l3j_0p8>; + vdda12-supply = <&vreg_l2j_1p2>; + + status = "okay"; +}; + +&usb_1_ss0_qmpphy { + vdda-phy-supply = <&vreg_l2j_1p2>; + vdda-pll-supply = <&vreg_l1j_0p8>; + + status = "okay"; +}; + +&usb_1_ss1 { + status = "okay"; +}; + +&usb_1_ss1_dwc3 { + dr_mode = "otg"; + usb-role-switch; +}; + +&usb_1_ss1_hsphy { + vdd-supply = <&vreg_l3j_0p8>; + vdda12-supply = <&vreg_l2j_1p2>; + + status = "okay"; +}; + +&usb_1_ss1_qmpphy { + vdda-phy-supply = <&vreg_l2j_1p2>; + vdda-pll-supply = <&vreg_l2d_0p9>; + + status = "okay"; +}; + +&usb_1_ss2 { + status = "okay"; +}; + +&usb_1_ss2_dwc3 { + dr_mode = "otg"; + usb-role-switch; +}; + +&usb_1_ss2_hsphy { + vdd-supply = <&vreg_l3j_0p8>; + vdda12-supply = <&vreg_l2j_1p2>; + + status = "okay"; +}; + +&usb_1_ss2_qmpphy { + vdda-phy-supply = <&vreg_l2j_1p2>; + vdda-pll-supply = <&vreg_l2d_0p9>; + + status = "okay"; +}; + +&usb_2 { + status = "okay"; +}; + +&usb_2_dwc3 { + dr_mode = "host"; +}; + +&usb_2_hsphy { + vdd-supply = <&vreg_l2e_0p8>; + vdda12-supply = <&vreg_l3e_1p2>; + + status = "okay"; +}; + +&usb_mp { + status = "okay"; +}; + +&usb_mp_hsphy0 { + vdd-supply = <&vreg_l2e_0p8>; + vdda12-supply = <&vreg_l3e_1p2>; + + status = "okay"; +}; + +&usb_mp_hsphy1 { + vdd-supply = <&vreg_l2e_0p8>; + vdda12-supply = <&vreg_l3e_1p2>; + + status = "okay"; +}; + +&usb_mp_qmpphy0 { + vdda-phy-supply = <&vreg_l3e_1p2>; + vdda-pll-supply = <&vreg_l3c_0p8>; + + status = "okay"; +}; + +&usb_mp_qmpphy1 { + vdda-phy-supply = <&vreg_l3e_1p2>; + vdda-pll-supply = <&vreg_l3c_0p8>; + + status = "okay"; +}; -- 2.34.1 ^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH v8 3/3] arm64: dts: qcom: Add base HAMOA-IOT-EVK board 2025-08-28 4:48 [PATCH v8 0/3] Initial support for Qualcomm Hamoa IOT EVK board Yijie Yang 2025-08-28 4:48 ` [PATCH v8 1/3] dt-bindings: arm: qcom: Document HAMOA-IOT-EVK board Yijie Yang 2025-08-28 4:48 ` [PATCH v8 2/3] arm64: dts: qcom: Add HAMOA-IOT-SOM platform Yijie Yang @ 2025-08-28 4:48 ` Yijie Yang 2025-08-28 11:15 ` Dmitry Baryshkov 2025-08-28 11:18 ` Dmitry Baryshkov 2 siblings, 2 replies; 13+ messages in thread From: Yijie Yang @ 2025-08-28 4:48 UTC (permalink / raw) To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley Cc: linux-arm-msm, devicetree, linux-kernel, Yijie Yang The HAMOA-IOT-EVK is an evaluation platform for IoT products, composed of the Hamoa IoT SoM and a carrier board. Together, they form a complete embedded system capable of booting to UART. This change enables the following peripherals on the carrier board: - UART - On-board regulators - USB Type-C mux - Pinctrl - Embedded USB (EUSB) repeaters - NVMe - pmic-glink - USB DisplayPorts - Bluetooth - Graphic - Audio Written in collaboration with Quill Qi (Audio) <le.qi@oss.qualcomm.com>, Jie Zhang (Graphics) <quic_jiezh@quicinc.com>, Shuai Zhang (Bluetooth) <quic_shuaz@quicinc.com>, and Yongxing Mou (USB DisplayPorts) <quic_yongmou@quicinc.com>. Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com> --- arch/arm64/boot/dts/qcom/Makefile | 1 + arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts | 1247 ++++++++++++++++++++++++++++ 2 files changed, 1248 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 94a84770b080..5e19535ad63d 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -13,6 +13,7 @@ dtb-$(CONFIG_ARCH_QCOM) += apq8039-t2.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8094-sony-xperia-kitakami-karin_windy.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb +dtb-$(CONFIG_ARCH_QCOM) += hamoa-iot-evk.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq5018-rdp432-c2.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq5018-tplink-archer-ax55-v1.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq5332-rdp441.dtb diff --git a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts new file mode 100644 index 000000000000..b1a8380d6639 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts @@ -0,0 +1,1247 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. + */ + +/dts-v1/; + +#include "hamoa-iot-som.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. Hamoa IoT EVK"; + compatible = "qcom,hamoa-iot-evk", "qcom,hamoa-iot-som", "qcom,x1e80100"; + chassis-type = "embedded"; + + aliases { + serial0 = &uart21; + serial1 = &uart14; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + pmic-glink { + compatible = "qcom,x1e80100-pmic-glink", + "qcom,sm8550-pmic-glink", + "qcom,pmic-glink"; + #address-cells = <1>; + #size-cells = <0>; + orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>, + <&tlmm 123 GPIO_ACTIVE_HIGH>, + <&tlmm 125 GPIO_ACTIVE_HIGH>; + + connector@0 { + compatible = "usb-c-connector"; + reg = <0>; + power-role = "dual"; + data-role = "dual"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + pmic_glink_ss0_hs_in: endpoint { + remote-endpoint = <&usb_1_ss0_dwc3_hs>; + }; + }; + + port@1 { + reg = <1>; + + pmic_glink_ss0_ss_in: endpoint { + remote-endpoint = <&usb_1_ss0_qmpphy_out>; + }; + }; + + port@2 { + reg = <2>; + + pmic_glink_ss0_sbu: endpoint { + remote-endpoint = <&usb_1_ss0_sbu_mux>; + }; + }; + }; + }; + + connector@1 { + compatible = "usb-c-connector"; + reg = <1>; + power-role = "dual"; + data-role = "dual"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + pmic_glink_ss1_hs_in: endpoint { + remote-endpoint = <&usb_1_ss1_dwc3_hs>; + }; + }; + + port@1 { + reg = <1>; + + pmic_glink_ss1_ss_in: endpoint { + remote-endpoint = <&retimer_ss1_ss_out>; + }; + }; + + port@2 { + reg = <2>; + + pmic_glink_ss1_con_sbu_in: endpoint { + remote-endpoint = <&retimer_ss1_con_sbu_out>; + }; + }; + }; + }; + + connector@2 { + compatible = "usb-c-connector"; + reg = <2>; + power-role = "dual"; + data-role = "dual"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + pmic_glink_ss2_hs_in: endpoint { + remote-endpoint = <&usb_1_ss2_dwc3_hs>; + }; + }; + + port@1 { + reg = <1>; + + pmic_glink_ss2_ss_in: endpoint { + remote-endpoint = <&retimer_ss2_ss_out>; + }; + }; + + port@2 { + reg = <2>; + + pmic_glink_ss2_con_sbu_in: endpoint { + remote-endpoint = <&retimer_ss2_con_sbu_out>; + }; + }; + }; + }; + }; + + vreg_edp_3p3: regulator-edp-3p3 { + compatible = "regulator-fixed"; + + regulator-name = "VREG_EDP_3P3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&edp_reg_en>; + pinctrl-names = "default"; + + regulator-boot-on; + }; + + sound { + compatible = "qcom,x1e80100-sndcard"; + model = "X1E80100-EVK"; + audio-routing = "WooferLeft IN", + "WSA WSA_SPK1 OUT", + "TweeterLeft IN", + "WSA WSA_SPK2 OUT", + "WooferRight IN", + "WSA2 WSA_SPK2 OUT", + "TweeterRight IN", + "WSA2 WSA_SPK2 OUT", + "IN1_HPHL", + "HPHL_OUT", + "IN2_HPHR", + "HPHR_OUT", + "AMIC2", + "MIC BIAS2", + "VA DMIC0", + "MIC BIAS3", + "VA DMIC1", + "MIC BIAS3", + "VA DMIC2", + "MIC BIAS1", + "VA DMIC3", + "MIC BIAS1", + "VA DMIC0", + "VA MIC BIAS3", + "VA DMIC1", + "VA MIC BIAS3", + "VA DMIC2", + "VA MIC BIAS1", + "VA DMIC3", + "VA MIC BIAS1", + "TX SWR_INPUT1", + "ADC2_OUTPUT"; + + wcd-playback-dai-link { + link-name = "WCD Playback"; + + codec { + sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>; + }; + + cpu { + sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>; + }; + + platform { + sound-dai = <&q6apm>; + }; + }; + + wcd-capture-dai-link { + link-name = "WCD Capture"; + + codec { + sound-dai = <&wcd938x 1>, <&swr2 1>, <&lpass_txmacro 0>; + }; + + cpu { + sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>; + }; + + platform { + sound-dai = <&q6apm>; + }; + }; + + wsa-dai-link { + link-name = "WSA Playback"; + + codec { + sound-dai = <&left_woofer>, + <&left_tweeter>, + <&swr0 0>, + <&lpass_wsamacro 0>, + <&right_woofer>, + <&right_tweeter>, + <&swr3 0>, + <&lpass_wsa2macro 0>; + }; + + cpu { + sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>; + }; + + platform { + sound-dai = <&q6apm>; + }; + }; + + va-dai-link { + link-name = "VA Capture"; + + codec { + sound-dai = <&lpass_vamacro 0>; + }; + + cpu { + sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>; + }; + + platform { + sound-dai = <&q6apm>; + }; + }; + }; + + vph_pwr: regulator-vph-pwr { + compatible = "regulator-fixed"; + + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + + regulator-always-on; + regulator-boot-on; + }; + + vreg_nvme: regulator-nvme { + compatible = "regulator-fixed"; + + regulator-name = "VREG_NVME_3P3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&nvme_reg_en>; + pinctrl-names = "default"; + + regulator-boot-on; + }; + + /* Left unused as the retimer is not used on this board. */ + vreg_rtmr0_1p15: regulator-rtmr0-1p15 { + compatible = "regulator-fixed"; + + regulator-name = "VREG_RTMR0_1P15"; + regulator-min-microvolt = <1150000>; + regulator-max-microvolt = <1150000>; + + gpio = <&pmc8380_5_gpios 8 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&usb0_pwr_1p15_reg_en>; + pinctrl-names = "default"; + + regulator-boot-on; + }; + + vreg_rtmr0_1p8: regulator-rtmr0-1p8 { + compatible = "regulator-fixed"; + + regulator-name = "VREG_RTMR0_1P8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + gpio = <&pm8550ve_9_gpios 8 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&usb0_1p8_reg_en>; + pinctrl-names = "default"; + + regulator-boot-on; + }; + + vreg_rtmr0_3p3: regulator-rtmr0-3p3 { + compatible = "regulator-fixed"; + + regulator-name = "VREG_RTMR0_3P3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&pm8550_gpios 11 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&usb0_3p3_reg_en>; + pinctrl-names = "default"; + + regulator-boot-on; + }; + + vreg_rtmr1_1p15: regulator-rtmr1-1p15 { + compatible = "regulator-fixed"; + + regulator-name = "VREG_RTMR1_1P15"; + regulator-min-microvolt = <1150000>; + regulator-max-microvolt = <1150000>; + + gpio = <&tlmm 188 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&usb1_pwr_1p15_reg_en>; + pinctrl-names = "default"; + + regulator-boot-on; + }; + + vreg_rtmr1_1p8: regulator-rtmr1-1p8 { + compatible = "regulator-fixed"; + + regulator-name = "VREG_RTMR1_1P8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + gpio = <&tlmm 175 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&usb1_pwr_1p8_reg_en>; + pinctrl-names = "default"; + + regulator-boot-on; + }; + + vreg_rtmr1_3p3: regulator-rtmr1-3p3 { + compatible = "regulator-fixed"; + + regulator-name = "VREG_RTMR1_3P3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 186 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&usb1_pwr_3p3_reg_en>; + pinctrl-names = "default"; + + regulator-boot-on; + }; + + vreg_rtmr2_1p15: regulator-rtmr2-1p15 { + compatible = "regulator-fixed"; + + regulator-name = "VREG_RTMR2_1P15"; + regulator-min-microvolt = <1150000>; + regulator-max-microvolt = <1150000>; + + gpio = <&tlmm 189 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&usb2_pwr_1p15_reg_en>; + pinctrl-names = "default"; + + regulator-boot-on; + }; + + vreg_rtmr2_1p8: regulator-rtmr2-1p8 { + compatible = "regulator-fixed"; + + regulator-name = "VREG_RTMR2_1P8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + gpio = <&tlmm 126 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&usb2_pwr_1p8_reg_en>; + pinctrl-names = "default"; + + regulator-boot-on; + }; + + vreg_rtmr2_3p3: regulator-rtmr2-3p3 { + compatible = "regulator-fixed"; + + regulator-name = "VREG_RTMR2_3P3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 187 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&usb2_pwr_3p3_reg_en>; + pinctrl-names = "default"; + + regulator-boot-on; + }; + + vreg_wcn_3p3: regulator-wcn-3p3 { + compatible = "regulator-fixed"; + + regulator-name = "VREG_WCN_3P3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 214 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&wcn_sw_en>; + pinctrl-names = "default"; + + regulator-always-on; + }; + + usb-1-ss0-sbu-mux { + compatible = "onnn,fsusb42", "gpio-sbu-mux"; + + enable-gpios = <&tlmm 168 GPIO_ACTIVE_LOW>; + select-gpios = <&tlmm 167 GPIO_ACTIVE_HIGH>; + + pinctrl-0 = <&usb_1_ss0_sbu_default>; + pinctrl-names = "default"; + + mode-switch; + orientation-switch; + + port { + usb_1_ss0_sbu_mux: endpoint { + remote-endpoint = <&pmic_glink_ss0_sbu>; + }; + }; + }; + + /* + * TODO: These two regulators are actually part of the removable M.2 + * card and not the CRD mainboard. Need to describe this differently. + * Functionally it works correctly, because all we need to do is to + * turn on the actual 3.3V supply above. + */ + vreg_wcn_0p95: regulator-wcn-0p95 { + compatible = "regulator-fixed"; + + regulator-name = "VREG_WCN_0P95"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <950000>; + + vin-supply = <&vreg_wcn_3p3>; + }; + + vreg_wcn_1p9: regulator-wcn-1p9 { + compatible = "regulator-fixed"; + + regulator-name = "VREG_WCN_1P9"; + regulator-min-microvolt = <1900000>; + regulator-max-microvolt = <1900000>; + + vin-supply = <&vreg_wcn_3p3>; + }; + + vreg_wwan: regulator-wwan { + compatible = "regulator-fixed"; + + regulator-name = "SDX_VPH_PWR"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 221 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <&wwan_sw_en>; + pinctrl-names = "default"; + + regulator-boot-on; + }; + + wcd938x: audio-codec { + compatible = "qcom,wcd9385-codec"; + + pinctrl-0 = <&wcd_default>; + pinctrl-names = "default"; + + reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>; + + qcom,micbias1-microvolt = <1800000>; + qcom,micbias2-microvolt = <1800000>; + qcom,micbias3-microvolt = <1800000>; + qcom,micbias4-microvolt = <1800000>; + qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 + 500000 500000 500000 500000>; + qcom,mbhc-headset-vthreshold-microvolt = <1700000>; + qcom,mbhc-headphone-vthreshold-microvolt = <50000>; + qcom,rx-device = <&wcd_rx>; + qcom,tx-device = <&wcd_tx>; + + vdd-buck-supply = <&vreg_l15b_1p8>; + vdd-rxtx-supply = <&vreg_l15b_1p8>; + vdd-io-supply = <&vreg_l15b_1p8>; + vdd-mic-bias-supply = <&vreg_bob1>; + + #sound-dai-cells = <1>; + }; + + wcn7850-pmu { + compatible = "qcom,wcn7850-pmu"; + + vdd-supply = <&vreg_wcn_0p95>; + vddio-supply = <&vreg_l15b_1p8>; + vddaon-supply = <&vreg_wcn_0p95>; + vdddig-supply = <&vreg_wcn_0p95>; + vddrfa1p2-supply = <&vreg_wcn_1p9>; + vddrfa1p8-supply = <&vreg_wcn_1p9>; + + bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>; + + pinctrl-0 = <&wcn_bt_en>; + pinctrl-names = "default"; + + regulators { + vreg_pmu_rfa_cmn: ldo0 { + regulator-name = "vreg_pmu_rfa_cmn"; + }; + + vreg_pmu_aon_0p59: ldo1 { + regulator-name = "vreg_pmu_aon_0p59"; + }; + + vreg_pmu_wlcx_0p8: ldo2 { + regulator-name = "vreg_pmu_wlcx_0p8"; + }; + + vreg_pmu_wlmx_0p85: ldo3 { + regulator-name = "vreg_pmu_wlmx_0p85"; + }; + + vreg_pmu_btcmx_0p85: ldo4 { + regulator-name = "vreg_pmu_btcmx_0p85"; + }; + + vreg_pmu_rfa_0p8: ldo5 { + regulator-name = "vreg_pmu_rfa_0p8"; + }; + + vreg_pmu_rfa_1p2: ldo6 { + regulator-name = "vreg_pmu_rfa_1p2"; + }; + + vreg_pmu_rfa_1p8: ldo7 { + regulator-name = "vreg_pmu_rfa_1p8"; + }; + + vreg_pmu_pcie_0p9: ldo8 { + regulator-name = "vreg_pmu_pcie_0p9"; + }; + + vreg_pmu_pcie_1p8: ldo9 { + regulator-name = "vreg_pmu_pcie_1p8"; + }; + }; + }; +}; + +&gpu { + status = "okay"; +}; + +&gpu_zap_shader { + firmware-name = "qcom/x1e80100/gen70500_zap.mbn"; +}; + +&i2c1 { + clock-frequency = <400000>; + status = "okay"; + + typec-mux@8 { + compatible = "parade,ps8830"; + reg = <0x08>; + + clocks = <&rpmhcc RPMH_RF_CLK5>; + + vdd-supply = <&vreg_rtmr2_1p15>; + vdd33-supply = <&vreg_rtmr2_3p3>; + vdd33-cap-supply = <&vreg_rtmr2_3p3>; + vddar-supply = <&vreg_rtmr2_1p15>; + vddat-supply = <&vreg_rtmr2_1p15>; + vddio-supply = <&vreg_rtmr2_1p8>; + + reset-gpios = <&tlmm 185 GPIO_ACTIVE_LOW>; + + pinctrl-0 = <&rtmr2_default>; + pinctrl-names = "default"; + + orientation-switch; + retimer-switch; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + retimer_ss2_ss_out: endpoint { + remote-endpoint = <&pmic_glink_ss2_ss_in>; + }; + }; + + port@1 { + reg = <1>; + + retimer_ss2_ss_in: endpoint { + remote-endpoint = <&usb_1_ss2_qmpphy_out>; + }; + }; + + port@2 { + reg = <2>; + + retimer_ss2_con_sbu_out: endpoint { + remote-endpoint = <&pmic_glink_ss2_con_sbu_in>; + }; + }; + }; + }; +}; + +&i2c5 { + clock-frequency = <400000>; + status = "okay"; + + eusb3_repeater: redriver@47 { + compatible = "nxp,ptn3222"; + reg = <0x47>; + #phy-cells = <0>; + + vdd3v3-supply = <&vreg_l13b_3p0>; + vdd1v8-supply = <&vreg_l4b_1p8>; + + reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>; + + pinctrl-0 = <&eusb3_reset_n>; + pinctrl-names = "default"; + }; + + eusb5_repeater: redriver@43 { + compatible = "nxp,ptn3222"; + reg = <0x43>; + #phy-cells = <0>; + + vdd3v3-supply = <&vreg_l13b_3p0>; + vdd1v8-supply = <&vreg_l4b_1p8>; + + reset-gpios = <&tlmm 7 GPIO_ACTIVE_LOW>; + + pinctrl-0 = <&eusb5_reset_n>; + pinctrl-names = "default"; + }; + + eusb6_repeater: redriver@4f { + compatible = "nxp,ptn3222"; + reg = <0x4f>; + #phy-cells = <0>; + + vdd3v3-supply = <&vreg_l13b_3p0>; + vdd1v8-supply = <&vreg_l4b_1p8>; + + reset-gpios = <&tlmm 184 GPIO_ACTIVE_LOW>; + + pinctrl-0 = <&eusb6_reset_n>; + pinctrl-names = "default"; + }; +}; + +&i2c7 { + clock-frequency = <400000>; + + status = "okay"; + + typec-mux@8 { + compatible = "parade,ps8830"; + reg = <0x8>; + + clocks = <&rpmhcc RPMH_RF_CLK4>; + + vdd-supply = <&vreg_rtmr1_1p15>; + vdd33-supply = <&vreg_rtmr1_3p3>; + vdd33-cap-supply = <&vreg_rtmr1_3p3>; + vddar-supply = <&vreg_rtmr1_1p15>; + vddat-supply = <&vreg_rtmr1_1p15>; + vddio-supply = <&vreg_rtmr1_1p8>; + + reset-gpios = <&tlmm 176 GPIO_ACTIVE_LOW>; + + pinctrl-0 = <&rtmr1_default>; + pinctrl-names = "default"; + + retimer-switch; + orientation-switch; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + retimer_ss1_ss_out: endpoint { + remote-endpoint = <&pmic_glink_ss1_ss_in>; + }; + }; + + port@1 { + reg = <1>; + + retimer_ss1_ss_in: endpoint { + remote-endpoint = <&usb_1_ss1_qmpphy_out>; + }; + }; + + port@2 { + reg = <2>; + + retimer_ss1_con_sbu_out: endpoint { + remote-endpoint = <&pmic_glink_ss1_con_sbu_in>; + }; + }; + }; + }; +}; + +&lpass_tlmm { + spkr_01_sd_n_active: spkr-01-sd-n-active-state { + pins = "gpio12"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + output-low; + }; + + spkr_23_sd_n_active: spkr-23-sd-n-active-state { + pins = "gpio13"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + output-low; + }; +}; + +&lpass_vamacro { + pinctrl-0 = <&dmic01_default>, <&dmic23_default>; + pinctrl-names = "default"; + + vdd-micb-supply = <&vreg_l1b_1p8>; + qcom,dmic-sample-rate = <4800000>; +}; + +&mdss { + status = "okay"; +}; + +&mdss_dp0 { + status = "okay"; +}; + +&mdss_dp0_out { + data-lanes = <0 1>; + link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>; +}; + +&mdss_dp1 { + status = "okay"; +}; + +&mdss_dp1_out { + data-lanes = <0 1>; + link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>; +}; + +&mdss_dp2 { + status = "okay"; +}; + +&mdss_dp2_out { + data-lanes = <0 1>; + link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>; +}; + +&mdss_dp3 { + /delete-property/ #sound-dai-cells; + + status = "okay"; + + aux-bus { + panel { + compatible = "edp-panel"; + power-supply = <&vreg_edp_3p3>; + + port { + edp_panel_in: endpoint { + remote-endpoint = <&mdss_dp3_out>; + }; + }; + }; + }; +}; + +&mdss_dp3_out { + data-lanes = <0 1 2 3>; + link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>; + + remote-endpoint = <&edp_panel_in>; +}; + +&mdss_dp3_phy { + vdda-phy-supply = <&vreg_l3j_0p8>; + vdda-pll-supply = <&vreg_l2j_1p2>; + + status = "okay"; +}; + +&pcie6a { + vddpe-3v3-supply = <&vreg_nvme>; +}; + +&pm8550_gpios { + rtmr0_default: rtmr0-reset-n-active-state { + pins = "gpio10"; + function = "normal"; + power-source = <1>; /* 1.8V */ + bias-disable; + input-disable; + output-enable; + }; + + usb0_3p3_reg_en: usb0-3p3-reg-en-state { + pins = "gpio11"; + function = "normal"; + power-source = <1>; /* 1.8V */ + bias-disable; + input-disable; + output-enable; + }; +}; + +&pm8550ve_9_gpios { + usb0_1p8_reg_en: usb0-1p8-reg-en-state { + pins = "gpio8"; + function = "normal"; + power-source = <1>; /* 1.8V */ + bias-disable; + input-disable; + output-enable; + }; +}; + +&pmc8380_5_gpios { + usb0_pwr_1p15_reg_en: usb0-pwr-1p15-reg-en-state { + pins = "gpio8"; + function = "normal"; + power-source = <1>; /* 1.8V */ + bias-disable; + input-disable; + output-enable; + }; +}; + +&smb2360_0 { + status = "okay"; +}; + +&smb2360_0_eusb2_repeater { + vdd18-supply = <&vreg_l3d_1p8>; + vdd3-supply = <&vreg_l2b_3p0>; +}; + +&smb2360_1 { + status = "okay"; +}; + +&smb2360_1_eusb2_repeater { + vdd18-supply = <&vreg_l3d_1p8>; + vdd3-supply = <&vreg_l14b_3p0>; +}; + +&smb2360_2 { + status = "okay"; +}; + +&smb2360_2_eusb2_repeater { + vdd18-supply = <&vreg_l3d_1p8>; + vdd3-supply = <&vreg_l8b_3p0>; +}; + +&swr0 { + status = "okay"; + + pinctrl-0 = <&wsa_swr_active>, <&spkr_01_sd_n_active>; + pinctrl-names = "default"; + + /* WSA8845, Left Woofer */ + left_woofer: speaker@0,0 { + compatible = "sdw20217020400"; + reg = <0 0>; + reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>; + #sound-dai-cells = <0>; + sound-name-prefix = "WooferLeft"; + vdd-1p8-supply = <&vreg_l15b_1p8>; + vdd-io-supply = <&vreg_l12b_1p2>; + qcom,port-mapping = <1 2 3 7 10 13>; + }; + + /* WSA8845, Left Tweeter */ + left_tweeter: speaker@0,1 { + compatible = "sdw20217020400"; + reg = <0 1>; + reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>; + #sound-dai-cells = <0>; + sound-name-prefix = "TweeterLeft"; + vdd-1p8-supply = <&vreg_l15b_1p8>; + vdd-io-supply = <&vreg_l12b_1p2>; + qcom,port-mapping = <4 5 6 7 11 13>; + }; +}; + +&swr1 { + status = "okay"; + + /* WCD9385 RX */ + wcd_rx: codec@0,4 { + compatible = "sdw20217010d00"; + reg = <0 4>; + qcom,rx-port-mapping = <1 2 3 4 5>; + }; +}; + +&swr2 { + status = "okay"; + + /* WCD9385 TX */ + wcd_tx: codec@0,3 { + compatible = "sdw20217010d00"; + reg = <0 3>; + qcom,tx-port-mapping = <2 2 3 4>; + }; +}; + +&swr3 { + status = "okay"; + + pinctrl-0 = <&wsa2_swr_active>, <&spkr_23_sd_n_active>; + pinctrl-names = "default"; + + /* WSA8845, Right Woofer */ + right_woofer: speaker@0,0 { + compatible = "sdw20217020400"; + reg = <0 0>; + reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>; + #sound-dai-cells = <0>; + sound-name-prefix = "WooferRight"; + vdd-1p8-supply = <&vreg_l15b_1p8>; + vdd-io-supply = <&vreg_l12b_1p2>; + qcom,port-mapping = <1 2 3 7 10 13>; + }; + + /* WSA8845, Right Tweeter */ + right_tweeter: speaker@0,1 { + compatible = "sdw20217020400"; + reg = <0 1>; + reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>; + #sound-dai-cells = <0>; + sound-name-prefix = "TweeterRight"; + vdd-1p8-supply = <&vreg_l15b_1p8>; + vdd-io-supply = <&vreg_l12b_1p2>; + qcom,port-mapping = <4 5 6 7 11 13>; + }; +}; + +&tlmm { + edp_reg_en: edp-reg-en-state { + pins = "gpio70"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + }; + + eusb3_reset_n: eusb3-reset-n-state { + pins = "gpio6"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + output-low; + }; + + eusb5_reset_n: eusb5-reset-n-state { + pins = "gpio7"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + output-low; + }; + + eusb6_reset_n: eusb6-reset-n-state { + pins = "gpio184"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + output-low; + }; + + nvme_reg_en: nvme-reg-en-state { + pins = "gpio18"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + rtmr1_default: rtmr1-reset-n-active-state { + pins = "gpio176"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + rtmr2_default: rtmr2-reset-n-active-state { + pins = "gpio185"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + usb1_pwr_1p15_reg_en: usb1-pwr-1p15-reg-en-state { + pins = "gpio188"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + usb1_pwr_1p8_reg_en: usb1-pwr-1p8-reg-en-state { + pins = "gpio175"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + usb1_pwr_3p3_reg_en: usb1-pwr-3p3-reg-en-state { + pins = "gpio186"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + usb2_pwr_1p15_reg_en: usb2-pwr-1p15-reg-en-state { + pins = "gpio189"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + usb2_pwr_1p8_reg_en: usb2-pwr-1p8-reg-en-state { + pins = "gpio126"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + usb2_pwr_3p3_reg_en: usb2-pwr-3p3-reg-en-state { + pins = "gpio187"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + usb_1_ss0_sbu_default: usb-1-ss0-sbu-state { + mode-pins { + pins = "gpio166"; + function = "gpio"; + bias-disable; + drive-strength = <2>; + output-high; + }; + + oe-n-pins { + pins = "gpio168"; + function = "gpio"; + bias-disable; + drive-strength = <2>; + }; + + sel-pins { + pins = "gpio167"; + function = "gpio"; + bias-disable; + drive-strength = <2>; + }; + }; + + wcd_default: wcd-reset-n-active-state { + pins = "gpio191"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + output-low; + }; + + wcn_bt_en: wcn-bt-en-state { + pins = "gpio116"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + wwan_sw_en: wwan-sw-en-state { + pins = "gpio221"; + function = "gpio"; + drive-strength = <4>; + bias-disable; + }; + + wcn_sw_en: wcn-sw-en-state { + pins = "gpio214"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + /* Switches USB signal routing between the USB connector and the Wi-Fi card. */ + wcn_usb_sw_n: wcn-usb-sw-n-state { + pins = "gpio225"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + output-high; + }; +}; + +&uart14 { + status = "okay"; + + bluetooth { + compatible = "qcom,wcn7850-bt"; + max-speed = <3200000>; + + vddaon-supply = <&vreg_pmu_aon_0p59>; + vddwlcx-supply = <&vreg_pmu_wlcx_0p8>; + vddwlmx-supply = <&vreg_pmu_wlmx_0p85>; + vddrfacmn-supply = <&vreg_pmu_rfa_cmn>; + vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>; + vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>; + vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>; + }; +}; + +&uart21 { + compatible = "qcom,geni-debug-uart"; + + status = "okay"; +}; + +&usb_1_ss0_dwc3_hs { + remote-endpoint = <&pmic_glink_ss0_hs_in>; +}; + +&usb_1_ss0_hsphy { + phys = <&smb2360_0_eusb2_repeater>; +}; + +&usb_1_ss0_qmpphy_out { + remote-endpoint = <&pmic_glink_ss0_ss_in>; +}; + +&usb_1_ss1_dwc3_hs { + remote-endpoint = <&pmic_glink_ss1_hs_in>; +}; + +&usb_1_ss1_hsphy { + phys = <&smb2360_1_eusb2_repeater>; +}; + +&usb_1_ss1_qmpphy_out { + remote-endpoint = <&retimer_ss1_ss_in>; +}; + +&usb_1_ss2_dwc3_hs { + remote-endpoint = <&pmic_glink_ss2_hs_in>; +}; + +&usb_1_ss2_hsphy { + phys = <&smb2360_2_eusb2_repeater>; +}; + +&usb_1_ss2_qmpphy_out { + remote-endpoint = <&retimer_ss2_ss_in>; +}; + +&usb_2_hsphy { + phys = <&eusb5_repeater>; + + pinctrl-0 = <&wcn_usb_sw_n>; + pinctrl-names = "default"; +}; + +&usb_mp_hsphy0 { + phys = <&eusb6_repeater>; +}; + +&usb_mp_hsphy1 { + phys = <&eusb3_repeater>; +}; -- 2.34.1 ^ permalink raw reply related [flat|nested] 13+ messages in thread
* Re: [PATCH v8 3/3] arm64: dts: qcom: Add base HAMOA-IOT-EVK board 2025-08-28 4:48 ` [PATCH v8 3/3] arm64: dts: qcom: Add base HAMOA-IOT-EVK board Yijie Yang @ 2025-08-28 11:15 ` Dmitry Baryshkov 2025-08-29 0:56 ` Yijie Yang 2025-08-28 11:18 ` Dmitry Baryshkov 1 sibling, 1 reply; 13+ messages in thread From: Dmitry Baryshkov @ 2025-08-28 11:15 UTC (permalink / raw) To: Yijie Yang Cc: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, linux-arm-msm, devicetree, linux-kernel On Thu, Aug 28, 2025 at 12:48:47PM +0800, Yijie Yang wrote: > The HAMOA-IOT-EVK is an evaluation platform for IoT products, composed of > the Hamoa IoT SoM and a carrier board. Together, they form a complete > embedded system capable of booting to UART. > > This change enables the following peripherals on the carrier board: > - UART > - On-board regulators > - USB Type-C mux > - Pinctrl > - Embedded USB (EUSB) repeaters > - NVMe > - pmic-glink > - USB DisplayPorts > - Bluetooth > - Graphic > - Audio > > Written in collaboration with Quill Qi (Audio) <le.qi@oss.qualcomm.com>, > Jie Zhang (Graphics) <quic_jiezh@quicinc.com>, Shuai Zhang (Bluetooth) > <quic_shuaz@quicinc.com>, and Yongxing Mou (USB DisplayPorts) > <quic_yongmou@quicinc.com>. > > Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com> > --- > arch/arm64/boot/dts/qcom/Makefile | 1 + > arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts | 1247 ++++++++++++++++++++++++++++ > 2 files changed, 1248 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile > index 94a84770b080..5e19535ad63d 100644 > --- a/arch/arm64/boot/dts/qcom/Makefile > +++ b/arch/arm64/boot/dts/qcom/Makefile > @@ -13,6 +13,7 @@ dtb-$(CONFIG_ARCH_QCOM) += apq8039-t2.dtb > dtb-$(CONFIG_ARCH_QCOM) += apq8094-sony-xperia-kitakami-karin_windy.dtb > dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb > dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb > +dtb-$(CONFIG_ARCH_QCOM) += hamoa-iot-evk.dtb > dtb-$(CONFIG_ARCH_QCOM) += ipq5018-rdp432-c2.dtb > dtb-$(CONFIG_ARCH_QCOM) += ipq5018-tplink-archer-ax55-v1.dtb > dtb-$(CONFIG_ARCH_QCOM) += ipq5332-rdp441.dtb > diff --git a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts > new file mode 100644 > index 000000000000..b1a8380d6639 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts > @@ -0,0 +1,1247 @@ > +// SPDX-License-Identifier: BSD-3-Clause > +/* > + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. > + */ > + > +/dts-v1/; > + > +#include "hamoa-iot-som.dtsi" > + > +/ { > + model = "Qualcomm Technologies, Inc. Hamoa IoT EVK"; > + compatible = "qcom,hamoa-iot-evk", "qcom,hamoa-iot-som", "qcom,x1e80100"; > + chassis-type = "embedded"; > + > + aliases { > + serial0 = &uart21; > + serial1 = &uart14; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + pmic-glink { > + compatible = "qcom,x1e80100-pmic-glink", > + "qcom,sm8550-pmic-glink", > + "qcom,pmic-glink"; > + #address-cells = <1>; > + #size-cells = <0>; > + orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>, > + <&tlmm 123 GPIO_ACTIVE_HIGH>, > + <&tlmm 125 GPIO_ACTIVE_HIGH>; > + > + connector@0 { > + compatible = "usb-c-connector"; > + reg = <0>; > + power-role = "dual"; > + data-role = "dual"; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + > + pmic_glink_ss0_hs_in: endpoint { > + remote-endpoint = <&usb_1_ss0_dwc3_hs>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + > + pmic_glink_ss0_ss_in: endpoint { > + remote-endpoint = <&usb_1_ss0_qmpphy_out>; > + }; > + }; > + > + port@2 { > + reg = <2>; > + > + pmic_glink_ss0_sbu: endpoint { > + remote-endpoint = <&usb_1_ss0_sbu_mux>; > + }; > + }; > + }; > + }; > + > + connector@1 { > + compatible = "usb-c-connector"; > + reg = <1>; > + power-role = "dual"; > + data-role = "dual"; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + > + pmic_glink_ss1_hs_in: endpoint { > + remote-endpoint = <&usb_1_ss1_dwc3_hs>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + > + pmic_glink_ss1_ss_in: endpoint { > + remote-endpoint = <&retimer_ss1_ss_out>; > + }; > + }; > + > + port@2 { > + reg = <2>; > + > + pmic_glink_ss1_con_sbu_in: endpoint { > + remote-endpoint = <&retimer_ss1_con_sbu_out>; > + }; > + }; > + }; > + }; > + > + connector@2 { > + compatible = "usb-c-connector"; > + reg = <2>; > + power-role = "dual"; > + data-role = "dual"; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + > + pmic_glink_ss2_hs_in: endpoint { > + remote-endpoint = <&usb_1_ss2_dwc3_hs>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + > + pmic_glink_ss2_ss_in: endpoint { > + remote-endpoint = <&retimer_ss2_ss_out>; > + }; > + }; > + > + port@2 { > + reg = <2>; > + > + pmic_glink_ss2_con_sbu_in: endpoint { > + remote-endpoint = <&retimer_ss2_con_sbu_out>; > + }; > + }; > + }; > + }; > + }; > + > + vreg_edp_3p3: regulator-edp-3p3 { Here is a list of the top-level nodes defined in this DT. Does it look sorted? aliases chosen pmic-glink regulator-edp-3p3 sound regulator-vph-pwr regulator-nvme regulator-rtmr0-1p15 regulator-rtmr0-1p8 regulator-rtmr0-3p3 regulator-rtmr1-1p15 regulator-rtmr1-1p8 regulator-rtmr1-3p3 regulator-rtmr2-1p15 regulator-rtmr2-1p8 regulator-rtmr2-3p3 regulator-wcn-3p3 usb-1-ss0-sbu-mux regulator-wcn-0p95 regulator-wcn-1p9 regulator-wwan audio-codec wcn7850-pmu -- With best wishes Dmitry ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v8 3/3] arm64: dts: qcom: Add base HAMOA-IOT-EVK board 2025-08-28 11:15 ` Dmitry Baryshkov @ 2025-08-29 0:56 ` Yijie Yang 0 siblings, 0 replies; 13+ messages in thread From: Yijie Yang @ 2025-08-29 0:56 UTC (permalink / raw) To: Dmitry Baryshkov Cc: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, linux-arm-msm, devicetree, linux-kernel On 2025-08-28 19:15, Dmitry Baryshkov wrote: > On Thu, Aug 28, 2025 at 12:48:47PM +0800, Yijie Yang wrote: >> The HAMOA-IOT-EVK is an evaluation platform for IoT products, composed of >> the Hamoa IoT SoM and a carrier board. Together, they form a complete >> embedded system capable of booting to UART. >> >> This change enables the following peripherals on the carrier board: >> - UART >> - On-board regulators >> - USB Type-C mux >> - Pinctrl >> - Embedded USB (EUSB) repeaters >> - NVMe >> - pmic-glink >> - USB DisplayPorts >> - Bluetooth >> - Graphic >> - Audio >> >> Written in collaboration with Quill Qi (Audio) <le.qi@oss.qualcomm.com>, >> Jie Zhang (Graphics) <quic_jiezh@quicinc.com>, Shuai Zhang (Bluetooth) >> <quic_shuaz@quicinc.com>, and Yongxing Mou (USB DisplayPorts) >> <quic_yongmou@quicinc.com>. >> >> Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com> >> --- >> arch/arm64/boot/dts/qcom/Makefile | 1 + >> arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts | 1247 ++++++++++++++++++++++++++++ >> 2 files changed, 1248 insertions(+) >> >> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile >> index 94a84770b080..5e19535ad63d 100644 >> --- a/arch/arm64/boot/dts/qcom/Makefile >> +++ b/arch/arm64/boot/dts/qcom/Makefile >> @@ -13,6 +13,7 @@ dtb-$(CONFIG_ARCH_QCOM) += apq8039-t2.dtb >> dtb-$(CONFIG_ARCH_QCOM) += apq8094-sony-xperia-kitakami-karin_windy.dtb >> dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb >> dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb >> +dtb-$(CONFIG_ARCH_QCOM) += hamoa-iot-evk.dtb >> dtb-$(CONFIG_ARCH_QCOM) += ipq5018-rdp432-c2.dtb >> dtb-$(CONFIG_ARCH_QCOM) += ipq5018-tplink-archer-ax55-v1.dtb >> dtb-$(CONFIG_ARCH_QCOM) += ipq5332-rdp441.dtb >> diff --git a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts >> new file mode 100644 >> index 000000000000..b1a8380d6639 >> --- /dev/null >> +++ b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts >> @@ -0,0 +1,1247 @@ >> +// SPDX-License-Identifier: BSD-3-Clause >> +/* >> + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. >> + */ >> + >> +/dts-v1/; >> + >> +#include "hamoa-iot-som.dtsi" >> + >> +/ { >> + model = "Qualcomm Technologies, Inc. Hamoa IoT EVK"; >> + compatible = "qcom,hamoa-iot-evk", "qcom,hamoa-iot-som", "qcom,x1e80100"; >> + chassis-type = "embedded"; >> + >> + aliases { >> + serial0 = &uart21; >> + serial1 = &uart14; >> + }; >> + >> + chosen { >> + stdout-path = "serial0:115200n8"; >> + }; >> + >> + pmic-glink { >> + compatible = "qcom,x1e80100-pmic-glink", >> + "qcom,sm8550-pmic-glink", >> + "qcom,pmic-glink"; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>, >> + <&tlmm 123 GPIO_ACTIVE_HIGH>, >> + <&tlmm 125 GPIO_ACTIVE_HIGH>; >> + >> + connector@0 { >> + compatible = "usb-c-connector"; >> + reg = <0>; >> + power-role = "dual"; >> + data-role = "dual"; >> + >> + ports { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + port@0 { >> + reg = <0>; >> + >> + pmic_glink_ss0_hs_in: endpoint { >> + remote-endpoint = <&usb_1_ss0_dwc3_hs>; >> + }; >> + }; >> + >> + port@1 { >> + reg = <1>; >> + >> + pmic_glink_ss0_ss_in: endpoint { >> + remote-endpoint = <&usb_1_ss0_qmpphy_out>; >> + }; >> + }; >> + >> + port@2 { >> + reg = <2>; >> + >> + pmic_glink_ss0_sbu: endpoint { >> + remote-endpoint = <&usb_1_ss0_sbu_mux>; >> + }; >> + }; >> + }; >> + }; >> + >> + connector@1 { >> + compatible = "usb-c-connector"; >> + reg = <1>; >> + power-role = "dual"; >> + data-role = "dual"; >> + >> + ports { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + port@0 { >> + reg = <0>; >> + >> + pmic_glink_ss1_hs_in: endpoint { >> + remote-endpoint = <&usb_1_ss1_dwc3_hs>; >> + }; >> + }; >> + >> + port@1 { >> + reg = <1>; >> + >> + pmic_glink_ss1_ss_in: endpoint { >> + remote-endpoint = <&retimer_ss1_ss_out>; >> + }; >> + }; >> + >> + port@2 { >> + reg = <2>; >> + >> + pmic_glink_ss1_con_sbu_in: endpoint { >> + remote-endpoint = <&retimer_ss1_con_sbu_out>; >> + }; >> + }; >> + }; >> + }; >> + >> + connector@2 { >> + compatible = "usb-c-connector"; >> + reg = <2>; >> + power-role = "dual"; >> + data-role = "dual"; >> + >> + ports { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + port@0 { >> + reg = <0>; >> + >> + pmic_glink_ss2_hs_in: endpoint { >> + remote-endpoint = <&usb_1_ss2_dwc3_hs>; >> + }; >> + }; >> + >> + port@1 { >> + reg = <1>; >> + >> + pmic_glink_ss2_ss_in: endpoint { >> + remote-endpoint = <&retimer_ss2_ss_out>; >> + }; >> + }; >> + >> + port@2 { >> + reg = <2>; >> + >> + pmic_glink_ss2_con_sbu_in: endpoint { >> + remote-endpoint = <&retimer_ss2_con_sbu_out>; >> + }; >> + }; >> + }; >> + }; >> + }; >> + >> + vreg_edp_3p3: regulator-edp-3p3 { > > Here is a list of the top-level nodes defined in this DT. Does it look > sorted? > > aliases > chosen > pmic-glink > regulator-edp-3p3 > sound > regulator-vph-pwr > regulator-nvme > regulator-rtmr0-1p15 > regulator-rtmr0-1p8 > regulator-rtmr0-3p3 > regulator-rtmr1-1p15 > regulator-rtmr1-1p8 > regulator-rtmr1-3p3 > regulator-rtmr2-1p15 > regulator-rtmr2-1p8 > regulator-rtmr2-3p3 > regulator-wcn-3p3 > usb-1-ss0-sbu-mux > regulator-wcn-0p95 > regulator-wcn-1p9 > regulator-wwan > audio-codec > wcn7850-pmu > I'll get them sorted. > -- Best Regards, Yijie ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v8 3/3] arm64: dts: qcom: Add base HAMOA-IOT-EVK board 2025-08-28 4:48 ` [PATCH v8 3/3] arm64: dts: qcom: Add base HAMOA-IOT-EVK board Yijie Yang 2025-08-28 11:15 ` Dmitry Baryshkov @ 2025-08-28 11:18 ` Dmitry Baryshkov 2025-09-01 3:02 ` Yingying Tang 2025-09-01 8:00 ` Yijie Yang 1 sibling, 2 replies; 13+ messages in thread From: Dmitry Baryshkov @ 2025-08-28 11:18 UTC (permalink / raw) To: Yijie Yang Cc: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, linux-arm-msm, devicetree, linux-kernel On Thu, Aug 28, 2025 at 12:48:47PM +0800, Yijie Yang wrote: > The HAMOA-IOT-EVK is an evaluation platform for IoT products, composed of > the Hamoa IoT SoM and a carrier board. Together, they form a complete > embedded system capable of booting to UART. > > This change enables the following peripherals on the carrier board: > - UART > - On-board regulators > - USB Type-C mux > - Pinctrl > - Embedded USB (EUSB) repeaters > - NVMe > - pmic-glink > - USB DisplayPorts > - Bluetooth > - Graphic > - Audio > > Written in collaboration with Quill Qi (Audio) <le.qi@oss.qualcomm.com>, > Jie Zhang (Graphics) <quic_jiezh@quicinc.com>, Shuai Zhang (Bluetooth) > <quic_shuaz@quicinc.com>, and Yongxing Mou (USB DisplayPorts) > <quic_yongmou@quicinc.com>. > > Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com> > --- > arch/arm64/boot/dts/qcom/Makefile | 1 + > arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts | 1247 ++++++++++++++++++++++++++++ > 2 files changed, 1248 insertions(+) > > + > + wcd938x: audio-codec { > + compatible = "qcom,wcd9385-codec"; > + > + pinctrl-0 = <&wcd_default>; > + pinctrl-names = "default"; > + > + reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>; > + > + qcom,micbias1-microvolt = <1800000>; > + qcom,micbias2-microvolt = <1800000>; > + qcom,micbias3-microvolt = <1800000>; > + qcom,micbias4-microvolt = <1800000>; > + qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 > + 500000 500000 500000 500000>; Other platforms use a single line here. If you don't want to do it, align data to start from the same column rather than restarting from the column 1. > + qcom,mbhc-headset-vthreshold-microvolt = <1700000>; > + qcom,mbhc-headphone-vthreshold-microvolt = <50000>; > + qcom,rx-device = <&wcd_rx>; > + qcom,tx-device = <&wcd_tx>; > + > + vdd-buck-supply = <&vreg_l15b_1p8>; > + vdd-rxtx-supply = <&vreg_l15b_1p8>; > + vdd-io-supply = <&vreg_l15b_1p8>; > + vdd-mic-bias-supply = <&vreg_bob1>; > + > + #sound-dai-cells = <1>; > + }; > + > + wcn7850-pmu { > + compatible = "qcom,wcn7850-pmu"; > + > + vdd-supply = <&vreg_wcn_0p95>; > + vddio-supply = <&vreg_l15b_1p8>; > + vddaon-supply = <&vreg_wcn_0p95>; > + vdddig-supply = <&vreg_wcn_0p95>; > + vddrfa1p2-supply = <&vreg_wcn_1p9>; > + vddrfa1p8-supply = <&vreg_wcn_1p9>; > + > + bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>; Okay, so how is WiFi controlled? Is there a GPIO? The DT should be describing the hardware, not the UEFI behaviour. > + > + pinctrl-0 = <&wcn_bt_en>; > + pinctrl-names = "default"; > + -- With best wishes Dmitry ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v8 3/3] arm64: dts: qcom: Add base HAMOA-IOT-EVK board 2025-08-28 11:18 ` Dmitry Baryshkov @ 2025-09-01 3:02 ` Yingying Tang 2025-09-02 2:37 ` Dmitry Baryshkov 2025-09-01 8:00 ` Yijie Yang 1 sibling, 1 reply; 13+ messages in thread From: Yingying Tang @ 2025-09-01 3:02 UTC (permalink / raw) To: Dmitry Baryshkov, Yijie Yang Cc: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, linux-arm-msm, devicetree, linux-kernel, Yingying Tang, miaoqing.pan, stone Zhang (Stone), zhichen On 8/28/2025 7:18 PM, Dmitry Baryshkov wrote: > On Thu, Aug 28, 2025 at 12:48:47PM +0800, Yijie Yang wrote: >> The HAMOA-IOT-EVK is an evaluation platform for IoT products, composed of >> the Hamoa IoT SoM and a carrier board. Together, they form a complete >> embedded system capable of booting to UART. >> >> This change enables the following peripherals on the carrier board: >> - UART >> - On-board regulators >> - USB Type-C mux >> - Pinctrl >> - Embedded USB (EUSB) repeaters >> - NVMe >> - pmic-glink >> - USB DisplayPorts >> - Bluetooth >> - Graphic >> - Audio >> >> Written in collaboration with Quill Qi (Audio) <le.qi@oss.qualcomm.com>, >> Jie Zhang (Graphics) <quic_jiezh@quicinc.com>, Shuai Zhang (Bluetooth) >> <quic_shuaz@quicinc.com>, and Yongxing Mou (USB DisplayPorts) >> <quic_yongmou@quicinc.com>. >> >> Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com> >> --- >> arch/arm64/boot/dts/qcom/Makefile | 1 + >> arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts | 1247 ++++++++++++++++++++++++++++ >> 2 files changed, 1248 insertions(+) >> >> + >> + wcd938x: audio-codec { >> + compatible = "qcom,wcd9385-codec"; >> + >> + pinctrl-0 = <&wcd_default>; >> + pinctrl-names = "default"; >> + >> + reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>; >> + >> + qcom,micbias1-microvolt = <1800000>; >> + qcom,micbias2-microvolt = <1800000>; >> + qcom,micbias3-microvolt = <1800000>; >> + qcom,micbias4-microvolt = <1800000>; >> + qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 >> + 500000 500000 500000 500000>; > > Other platforms use a single line here. If you don't want to do it, > align data to start from the same column rather than restarting from the > column 1. > >> + qcom,mbhc-headset-vthreshold-microvolt = <1700000>; >> + qcom,mbhc-headphone-vthreshold-microvolt = <50000>; >> + qcom,rx-device = <&wcd_rx>; >> + qcom,tx-device = <&wcd_tx>; >> + >> + vdd-buck-supply = <&vreg_l15b_1p8>; >> + vdd-rxtx-supply = <&vreg_l15b_1p8>; >> + vdd-io-supply = <&vreg_l15b_1p8>; >> + vdd-mic-bias-supply = <&vreg_bob1>; >> + >> + #sound-dai-cells = <1>; >> + }; >> + >> + wcn7850-pmu { >> + compatible = "qcom,wcn7850-pmu"; >> + >> + vdd-supply = <&vreg_wcn_0p95>; >> + vddio-supply = <&vreg_l15b_1p8>; >> + vddaon-supply = <&vreg_wcn_0p95>; >> + vdddig-supply = <&vreg_wcn_0p95>; >> + vddrfa1p2-supply = <&vreg_wcn_1p9>; >> + vddrfa1p8-supply = <&vreg_wcn_1p9>; >> + >> + bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>; > > Okay, so how is WiFi controlled? Is there a GPIO? The DT should be > describing the hardware, not the UEFI behaviour. > Hi Dmitry, as I described in previous mail, On hamoa platfrom whole wifi module's power supply and enable gpio are voted in UEFI. Hamoa is PC platform, so BIOS/UEFI behavior is compatible with Windows/ACPI architecture. UEFI is responsible for enabling power supply for all devices which may be used in boot phase (such as WLAN may be used to boot from network). So we need not Wifi chip's power and control GPIO in kernel side, thanks >> + >> + pinctrl-0 = <&wcn_bt_en>; >> + pinctrl-names = "default"; >> + > ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v8 3/3] arm64: dts: qcom: Add base HAMOA-IOT-EVK board 2025-09-01 3:02 ` Yingying Tang @ 2025-09-02 2:37 ` Dmitry Baryshkov 2025-09-02 6:56 ` Yingying Tang 0 siblings, 1 reply; 13+ messages in thread From: Dmitry Baryshkov @ 2025-09-02 2:37 UTC (permalink / raw) To: Yingying Tang Cc: Yijie Yang, Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, linux-arm-msm, devicetree, linux-kernel, Yingying Tang, miaoqing.pan, stone Zhang (Stone), zhichen On Mon, Sep 01, 2025 at 11:02:24AM +0800, Yingying Tang wrote: > > > On 8/28/2025 7:18 PM, Dmitry Baryshkov wrote: > > On Thu, Aug 28, 2025 at 12:48:47PM +0800, Yijie Yang wrote: > >> The HAMOA-IOT-EVK is an evaluation platform for IoT products, composed of > >> the Hamoa IoT SoM and a carrier board. Together, they form a complete > >> embedded system capable of booting to UART. > >> > >> This change enables the following peripherals on the carrier board: > >> - UART > >> - On-board regulators > >> - USB Type-C mux > >> - Pinctrl > >> - Embedded USB (EUSB) repeaters > >> - NVMe > >> - pmic-glink > >> - USB DisplayPorts > >> - Bluetooth > >> - Graphic > >> - Audio > >> > >> Written in collaboration with Quill Qi (Audio) <le.qi@oss.qualcomm.com>, > >> Jie Zhang (Graphics) <quic_jiezh@quicinc.com>, Shuai Zhang (Bluetooth) > >> <quic_shuaz@quicinc.com>, and Yongxing Mou (USB DisplayPorts) > >> <quic_yongmou@quicinc.com>. > >> > >> Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com> > >> --- > >> arch/arm64/boot/dts/qcom/Makefile | 1 + > >> arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts | 1247 ++++++++++++++++++++++++++++ > >> 2 files changed, 1248 insertions(+) > >> > >> + > >> + wcd938x: audio-codec { > >> + compatible = "qcom,wcd9385-codec"; > >> + > >> + pinctrl-0 = <&wcd_default>; > >> + pinctrl-names = "default"; > >> + > >> + reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>; > >> + > >> + qcom,micbias1-microvolt = <1800000>; > >> + qcom,micbias2-microvolt = <1800000>; > >> + qcom,micbias3-microvolt = <1800000>; > >> + qcom,micbias4-microvolt = <1800000>; > >> + qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 > >> + 500000 500000 500000 500000>; > > > > Other platforms use a single line here. If you don't want to do it, > > align data to start from the same column rather than restarting from the > > column 1. > > > >> + qcom,mbhc-headset-vthreshold-microvolt = <1700000>; > >> + qcom,mbhc-headphone-vthreshold-microvolt = <50000>; > >> + qcom,rx-device = <&wcd_rx>; > >> + qcom,tx-device = <&wcd_tx>; > >> + > >> + vdd-buck-supply = <&vreg_l15b_1p8>; > >> + vdd-rxtx-supply = <&vreg_l15b_1p8>; > >> + vdd-io-supply = <&vreg_l15b_1p8>; > >> + vdd-mic-bias-supply = <&vreg_bob1>; > >> + > >> + #sound-dai-cells = <1>; > >> + }; > >> + > >> + wcn7850-pmu { > >> + compatible = "qcom,wcn7850-pmu"; > >> + > >> + vdd-supply = <&vreg_wcn_0p95>; > >> + vddio-supply = <&vreg_l15b_1p8>; > >> + vddaon-supply = <&vreg_wcn_0p95>; > >> + vdddig-supply = <&vreg_wcn_0p95>; > >> + vddrfa1p2-supply = <&vreg_wcn_1p9>; > >> + vddrfa1p8-supply = <&vreg_wcn_1p9>; > >> + > >> + bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>; > > > > Okay, so how is WiFi controlled? Is there a GPIO? The DT should be > > describing the hardware, not the UEFI behaviour. > > > Hi Dmitry, as I described in previous mail, On hamoa platfrom whole wifi module's power supply and enable gpio are voted in UEFI. > Hamoa is PC platform, so BIOS/UEFI behavior is compatible with Windows/ACPI architecture. UEFI is responsible for enabling power supply > for all devices which may be used in boot phase (such as WLAN may be used to boot from network). This is not completely relevant. You are describing driver / Linux / bootloader behaviour. I asked if there is a GPIO in the hardware. If there is one, please add it here. > > So we need not Wifi chip's power and control GPIO in kernel side, thanks What if someone requests this GPIO from userspace and pulls it down? > >> + > >> + pinctrl-0 = <&wcn_bt_en>; > >> + pinctrl-names = "default"; > >> + > > > -- With best wishes Dmitry ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v8 3/3] arm64: dts: qcom: Add base HAMOA-IOT-EVK board 2025-09-02 2:37 ` Dmitry Baryshkov @ 2025-09-02 6:56 ` Yingying Tang 2025-09-02 9:50 ` Dmitry Baryshkov 2025-09-02 10:09 ` Konrad Dybcio 0 siblings, 2 replies; 13+ messages in thread From: Yingying Tang @ 2025-09-02 6:56 UTC (permalink / raw) To: Dmitry Baryshkov Cc: Yijie Yang, Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, linux-arm-msm, devicetree, linux-kernel, Yingying Tang, miaoqing.pan, stone Zhang (Stone), zhichen On 9/2/2025 10:37 AM, Dmitry Baryshkov wrote: > On Mon, Sep 01, 2025 at 11:02:24AM +0800, Yingying Tang wrote: >> >> >> On 8/28/2025 7:18 PM, Dmitry Baryshkov wrote: >>> On Thu, Aug 28, 2025 at 12:48:47PM +0800, Yijie Yang wrote: >>>> The HAMOA-IOT-EVK is an evaluation platform for IoT products, composed of >>>> the Hamoa IoT SoM and a carrier board. Together, they form a complete >>>> embedded system capable of booting to UART. >>>> >>>> This change enables the following peripherals on the carrier board: >>>> - UART >>>> - On-board regulators >>>> - USB Type-C mux >>>> - Pinctrl >>>> - Embedded USB (EUSB) repeaters >>>> - NVMe >>>> - pmic-glink >>>> - USB DisplayPorts >>>> - Bluetooth >>>> - Graphic >>>> - Audio >>>> >>>> Written in collaboration with Quill Qi (Audio) <le.qi@oss.qualcomm.com>, >>>> Jie Zhang (Graphics) <quic_jiezh@quicinc.com>, Shuai Zhang (Bluetooth) >>>> <quic_shuaz@quicinc.com>, and Yongxing Mou (USB DisplayPorts) >>>> <quic_yongmou@quicinc.com>. >>>> >>>> Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com> >>>> --- >>>> arch/arm64/boot/dts/qcom/Makefile | 1 + >>>> arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts | 1247 ++++++++++++++++++++++++++++ >>>> 2 files changed, 1248 insertions(+) >>>> >>>> + >>>> + wcd938x: audio-codec { >>>> + compatible = "qcom,wcd9385-codec"; >>>> + >>>> + pinctrl-0 = <&wcd_default>; >>>> + pinctrl-names = "default"; >>>> + >>>> + reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>; >>>> + >>>> + qcom,micbias1-microvolt = <1800000>; >>>> + qcom,micbias2-microvolt = <1800000>; >>>> + qcom,micbias3-microvolt = <1800000>; >>>> + qcom,micbias4-microvolt = <1800000>; >>>> + qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 >>>> + 500000 500000 500000 500000>; >>> >>> Other platforms use a single line here. If you don't want to do it, >>> align data to start from the same column rather than restarting from the >>> column 1. >>> >>>> + qcom,mbhc-headset-vthreshold-microvolt = <1700000>; >>>> + qcom,mbhc-headphone-vthreshold-microvolt = <50000>; >>>> + qcom,rx-device = <&wcd_rx>; >>>> + qcom,tx-device = <&wcd_tx>; >>>> + >>>> + vdd-buck-supply = <&vreg_l15b_1p8>; >>>> + vdd-rxtx-supply = <&vreg_l15b_1p8>; >>>> + vdd-io-supply = <&vreg_l15b_1p8>; >>>> + vdd-mic-bias-supply = <&vreg_bob1>; >>>> + >>>> + #sound-dai-cells = <1>; >>>> + }; >>>> + >>>> + wcn7850-pmu { >>>> + compatible = "qcom,wcn7850-pmu"; >>>> + >>>> + vdd-supply = <&vreg_wcn_0p95>; >>>> + vddio-supply = <&vreg_l15b_1p8>; >>>> + vddaon-supply = <&vreg_wcn_0p95>; >>>> + vdddig-supply = <&vreg_wcn_0p95>; >>>> + vddrfa1p2-supply = <&vreg_wcn_1p9>; >>>> + vddrfa1p8-supply = <&vreg_wcn_1p9>; >>>> + >>>> + bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>; >>> >>> Okay, so how is WiFi controlled? Is there a GPIO? The DT should be >>> describing the hardware, not the UEFI behaviour. >>> >> Hi Dmitry, as I described in previous mail, On hamoa platfrom whole wifi module's power supply and enable gpio are voted in UEFI. >> Hamoa is PC platform, so BIOS/UEFI behavior is compatible with Windows/ACPI architecture. UEFI is responsible for enabling power supply >> for all devices which may be used in boot phase (such as WLAN may be used to boot from network). > > This is not completely relevant. You are describing driver / Linux / > bootloader behaviour. I asked if there is a GPIO in the hardware. If > there is one, please add it here. Hi Dimitry, During the UEFI boot phase, the WLAN enable GPIO has already been asserted, and the WLAN chip is functioning normally. If we include this GPIO in the kernel device tree, when the kernel configures this GPIO, its voltage level may experience a brief glitch, which could cause the WLAN chip to reset and result in a PCIe link down. So I didn't add wlan-en-gpio in this hamoa's device tree. > >> >> So we need not Wifi chip's power and control GPIO in kernel side, thanks > > What if someone requests this GPIO from userspace and pulls it down? > >>>> + >>>> + pinctrl-0 = <&wcn_bt_en>; >>>> + pinctrl-names = "default"; >>>> + >>> >> > ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v8 3/3] arm64: dts: qcom: Add base HAMOA-IOT-EVK board 2025-09-02 6:56 ` Yingying Tang @ 2025-09-02 9:50 ` Dmitry Baryshkov 2025-09-02 10:09 ` Konrad Dybcio 1 sibling, 0 replies; 13+ messages in thread From: Dmitry Baryshkov @ 2025-09-02 9:50 UTC (permalink / raw) To: Yingying Tang Cc: Yijie Yang, Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, linux-arm-msm, devicetree, linux-kernel, Yingying Tang, miaoqing.pan, stone Zhang (Stone), zhichen On Tue, Sep 02, 2025 at 02:56:37PM +0800, Yingying Tang wrote: > > > On 9/2/2025 10:37 AM, Dmitry Baryshkov wrote: > > On Mon, Sep 01, 2025 at 11:02:24AM +0800, Yingying Tang wrote: > >> > >> > >> On 8/28/2025 7:18 PM, Dmitry Baryshkov wrote: > >>> On Thu, Aug 28, 2025 at 12:48:47PM +0800, Yijie Yang wrote: > >>>> The HAMOA-IOT-EVK is an evaluation platform for IoT products, composed of > >>>> the Hamoa IoT SoM and a carrier board. Together, they form a complete > >>>> embedded system capable of booting to UART. > >>>> > >>>> This change enables the following peripherals on the carrier board: > >>>> - UART > >>>> - On-board regulators > >>>> - USB Type-C mux > >>>> - Pinctrl > >>>> - Embedded USB (EUSB) repeaters > >>>> - NVMe > >>>> - pmic-glink > >>>> - USB DisplayPorts > >>>> - Bluetooth > >>>> - Graphic > >>>> - Audio > >>>> > >>>> Written in collaboration with Quill Qi (Audio) <le.qi@oss.qualcomm.com>, > >>>> Jie Zhang (Graphics) <quic_jiezh@quicinc.com>, Shuai Zhang (Bluetooth) > >>>> <quic_shuaz@quicinc.com>, and Yongxing Mou (USB DisplayPorts) > >>>> <quic_yongmou@quicinc.com>. > >>>> > >>>> Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com> > >>>> --- > >>>> arch/arm64/boot/dts/qcom/Makefile | 1 + > >>>> arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts | 1247 ++++++++++++++++++++++++++++ > >>>> 2 files changed, 1248 insertions(+) > >>>> > >>>> + > >>>> + wcd938x: audio-codec { > >>>> + compatible = "qcom,wcd9385-codec"; > >>>> + > >>>> + pinctrl-0 = <&wcd_default>; > >>>> + pinctrl-names = "default"; > >>>> + > >>>> + reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>; > >>>> + > >>>> + qcom,micbias1-microvolt = <1800000>; > >>>> + qcom,micbias2-microvolt = <1800000>; > >>>> + qcom,micbias3-microvolt = <1800000>; > >>>> + qcom,micbias4-microvolt = <1800000>; > >>>> + qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 > >>>> + 500000 500000 500000 500000>; > >>> > >>> Other platforms use a single line here. If you don't want to do it, > >>> align data to start from the same column rather than restarting from the > >>> column 1. > >>> > >>>> + qcom,mbhc-headset-vthreshold-microvolt = <1700000>; > >>>> + qcom,mbhc-headphone-vthreshold-microvolt = <50000>; > >>>> + qcom,rx-device = <&wcd_rx>; > >>>> + qcom,tx-device = <&wcd_tx>; > >>>> + > >>>> + vdd-buck-supply = <&vreg_l15b_1p8>; > >>>> + vdd-rxtx-supply = <&vreg_l15b_1p8>; > >>>> + vdd-io-supply = <&vreg_l15b_1p8>; > >>>> + vdd-mic-bias-supply = <&vreg_bob1>; > >>>> + > >>>> + #sound-dai-cells = <1>; > >>>> + }; > >>>> + > >>>> + wcn7850-pmu { > >>>> + compatible = "qcom,wcn7850-pmu"; > >>>> + > >>>> + vdd-supply = <&vreg_wcn_0p95>; > >>>> + vddio-supply = <&vreg_l15b_1p8>; > >>>> + vddaon-supply = <&vreg_wcn_0p95>; > >>>> + vdddig-supply = <&vreg_wcn_0p95>; > >>>> + vddrfa1p2-supply = <&vreg_wcn_1p9>; > >>>> + vddrfa1p8-supply = <&vreg_wcn_1p9>; > >>>> + > >>>> + bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>; > >>> > >>> Okay, so how is WiFi controlled? Is there a GPIO? The DT should be > >>> describing the hardware, not the UEFI behaviour. > >>> > >> Hi Dmitry, as I described in previous mail, On hamoa platfrom whole wifi module's power supply and enable gpio are voted in UEFI. > >> Hamoa is PC platform, so BIOS/UEFI behavior is compatible with Windows/ACPI architecture. UEFI is responsible for enabling power supply > >> for all devices which may be used in boot phase (such as WLAN may be used to boot from network). > > > > This is not completely relevant. You are describing driver / Linux / > > bootloader behaviour. I asked if there is a GPIO in the hardware. If > > there is one, please add it here. > > Hi Dimitry, > > During the UEFI boot phase, the WLAN enable GPIO has already been asserted, and the WLAN chip is functioning normally. > If we include this GPIO in the kernel device tree, when the kernel configures this GPIO, its voltage level may experience a brief glitch, which could cause the WLAN chip to reset and result in a PCIe link down. Here you are describing driver behaviour. It's a software issue and can be handled in the driver. I'm asking you to describe the hardware. From the hardware perspective there is a GPIO pin. Please describe it in the DT. > So I didn't add wlan-en-gpio in this hamoa's device tree. > > > > > > >> > >> So we need not Wifi chip's power and control GPIO in kernel side, thanks > > > > What if someone requests this GPIO from userspace and pulls it down? > > > >>>> + > >>>> + pinctrl-0 = <&wcn_bt_en>; > >>>> + pinctrl-names = "default"; > >>>> + > >>> > >> > > > -- With best wishes Dmitry ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v8 3/3] arm64: dts: qcom: Add base HAMOA-IOT-EVK board 2025-09-02 6:56 ` Yingying Tang 2025-09-02 9:50 ` Dmitry Baryshkov @ 2025-09-02 10:09 ` Konrad Dybcio 1 sibling, 0 replies; 13+ messages in thread From: Konrad Dybcio @ 2025-09-02 10:09 UTC (permalink / raw) To: Yingying Tang, Dmitry Baryshkov Cc: Yijie Yang, Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, linux-arm-msm, devicetree, linux-kernel, Yingying Tang, miaoqing.pan, stone Zhang (Stone), zhichen On 9/2/25 8:56 AM, Yingying Tang wrote: > > > On 9/2/2025 10:37 AM, Dmitry Baryshkov wrote: >> On Mon, Sep 01, 2025 at 11:02:24AM +0800, Yingying Tang wrote: >>> >>> >>> On 8/28/2025 7:18 PM, Dmitry Baryshkov wrote: >>>> On Thu, Aug 28, 2025 at 12:48:47PM +0800, Yijie Yang wrote: >>>>> The HAMOA-IOT-EVK is an evaluation platform for IoT products, composed of >>>>> the Hamoa IoT SoM and a carrier board. Together, they form a complete >>>>> embedded system capable of booting to UART. [...] >>>>> + wcn7850-pmu { >>>>> + compatible = "qcom,wcn7850-pmu"; >>>>> + >>>>> + vdd-supply = <&vreg_wcn_0p95>; >>>>> + vddio-supply = <&vreg_l15b_1p8>; >>>>> + vddaon-supply = <&vreg_wcn_0p95>; >>>>> + vdddig-supply = <&vreg_wcn_0p95>; >>>>> + vddrfa1p2-supply = <&vreg_wcn_1p9>; >>>>> + vddrfa1p8-supply = <&vreg_wcn_1p9>; >>>>> + >>>>> + bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>; >>>> >>>> Okay, so how is WiFi controlled? Is there a GPIO? The DT should be >>>> describing the hardware, not the UEFI behaviour. >>>> >>> Hi Dmitry, as I described in previous mail, On hamoa platfrom whole wifi module's power supply and enable gpio are voted in UEFI. >>> Hamoa is PC platform, so BIOS/UEFI behavior is compatible with Windows/ACPI architecture. UEFI is responsible for enabling power supply >>> for all devices which may be used in boot phase (such as WLAN may be used to boot from network). >> >> This is not completely relevant. You are describing driver / Linux / >> bootloader behaviour. I asked if there is a GPIO in the hardware. If >> there is one, please add it here. > > Hi Dimitry, > > During the UEFI boot phase, the WLAN enable GPIO has already been asserted, and the WLAN chip is functioning normally. > If we include this GPIO in the kernel device tree, when the kernel configures this GPIO, its voltage level may experience a brief glitch, which could cause the WLAN chip to reset and result in a PCIe link down. The WCN pwrseq code handles this already, please simply describe the hardware like the platform firmware description which you're creating is supposed to Konrad ^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v8 3/3] arm64: dts: qcom: Add base HAMOA-IOT-EVK board 2025-08-28 11:18 ` Dmitry Baryshkov 2025-09-01 3:02 ` Yingying Tang @ 2025-09-01 8:00 ` Yijie Yang 1 sibling, 0 replies; 13+ messages in thread From: Yijie Yang @ 2025-09-01 8:00 UTC (permalink / raw) To: Dmitry Baryshkov Cc: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley, linux-arm-msm, devicetree, linux-kernel On 2025-08-28 19:18, Dmitry Baryshkov wrote: > On Thu, Aug 28, 2025 at 12:48:47PM +0800, Yijie Yang wrote: >> The HAMOA-IOT-EVK is an evaluation platform for IoT products, composed of >> the Hamoa IoT SoM and a carrier board. Together, they form a complete >> embedded system capable of booting to UART. >> >> This change enables the following peripherals on the carrier board: >> - UART >> - On-board regulators >> - USB Type-C mux >> - Pinctrl >> - Embedded USB (EUSB) repeaters >> - NVMe >> - pmic-glink >> - USB DisplayPorts >> - Bluetooth >> - Graphic >> - Audio >> >> Written in collaboration with Quill Qi (Audio) <le.qi@oss.qualcomm.com>, >> Jie Zhang (Graphics) <quic_jiezh@quicinc.com>, Shuai Zhang (Bluetooth) >> <quic_shuaz@quicinc.com>, and Yongxing Mou (USB DisplayPorts) >> <quic_yongmou@quicinc.com>. >> >> Signed-off-by: Yijie Yang <yijie.yang@oss.qualcomm.com> >> --- >> arch/arm64/boot/dts/qcom/Makefile | 1 + >> arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts | 1247 ++++++++++++++++++++++++++++ >> 2 files changed, 1248 insertions(+) >> >> + >> + wcd938x: audio-codec { >> + compatible = "qcom,wcd9385-codec"; >> + >> + pinctrl-0 = <&wcd_default>; >> + pinctrl-names = "default"; >> + >> + reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>; >> + >> + qcom,micbias1-microvolt = <1800000>; >> + qcom,micbias2-microvolt = <1800000>; >> + qcom,micbias3-microvolt = <1800000>; >> + qcom,micbias4-microvolt = <1800000>; >> + qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 >> + 500000 500000 500000 500000>; > > Other platforms use a single line here. If you don't want to do it, > align data to start from the same column rather than restarting from the > column 1. I will update it to a single line. > >> + qcom,mbhc-headset-vthreshold-microvolt = <1700000>; >> + qcom,mbhc-headphone-vthreshold-microvolt = <50000>; >> + qcom,rx-device = <&wcd_rx>; >> + qcom,tx-device = <&wcd_tx>; >> + >> + vdd-buck-supply = <&vreg_l15b_1p8>; >> + vdd-rxtx-supply = <&vreg_l15b_1p8>; >> + vdd-io-supply = <&vreg_l15b_1p8>; >> + vdd-mic-bias-supply = <&vreg_bob1>; >> + >> + #sound-dai-cells = <1>; >> + }; >> + >> + wcn7850-pmu { >> + compatible = "qcom,wcn7850-pmu"; >> + >> + vdd-supply = <&vreg_wcn_0p95>; >> + vddio-supply = <&vreg_l15b_1p8>; >> + vddaon-supply = <&vreg_wcn_0p95>; >> + vdddig-supply = <&vreg_wcn_0p95>; >> + vddrfa1p2-supply = <&vreg_wcn_1p9>; >> + vddrfa1p8-supply = <&vreg_wcn_1p9>; >> + >> + bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>; > > Okay, so how is WiFi controlled? Is there a GPIO? The DT should be > describing the hardware, not the UEFI behaviour. > >> + >> + pinctrl-0 = <&wcn_bt_en>; >> + pinctrl-names = "default"; >> + > -- Best Regards, Yijie ^ permalink raw reply [flat|nested] 13+ messages in thread
end of thread, other threads:[~2025-09-02 10:09 UTC | newest] Thread overview: 13+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2025-08-28 4:48 [PATCH v8 0/3] Initial support for Qualcomm Hamoa IOT EVK board Yijie Yang 2025-08-28 4:48 ` [PATCH v8 1/3] dt-bindings: arm: qcom: Document HAMOA-IOT-EVK board Yijie Yang 2025-08-28 4:48 ` [PATCH v8 2/3] arm64: dts: qcom: Add HAMOA-IOT-SOM platform Yijie Yang 2025-08-28 4:48 ` [PATCH v8 3/3] arm64: dts: qcom: Add base HAMOA-IOT-EVK board Yijie Yang 2025-08-28 11:15 ` Dmitry Baryshkov 2025-08-29 0:56 ` Yijie Yang 2025-08-28 11:18 ` Dmitry Baryshkov 2025-09-01 3:02 ` Yingying Tang 2025-09-02 2:37 ` Dmitry Baryshkov 2025-09-02 6:56 ` Yingying Tang 2025-09-02 9:50 ` Dmitry Baryshkov 2025-09-02 10:09 ` Konrad Dybcio 2025-09-01 8:00 ` Yijie Yang
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).