* [PATCH 3/3] [media] atmel-isi: add primary DT support [not found] <1395141238-5948-1-git-send-email-josh.wu@atmel.com> @ 2014-03-18 11:19 ` Josh Wu 2014-03-18 13:36 ` Laurent Pinchart 0 siblings, 1 reply; 4+ messages in thread From: Josh Wu @ 2014-03-18 11:19 UTC (permalink / raw) To: g.liakhovetski Cc: linux-media, m.chehab, nicolas.ferre, linux-arm-kernel, grant.likely, galak, rob, mark.rutland, robh+dt, ijc+devicetree, pawel.moll, devicetree, Josh Wu This patch add the DT support for Atmel ISI driver. It use the same v4l2 DT interface that defined in video-interfaces.txt. Signed-off-by: Josh Wu <josh.wu@atmel.com> Cc: devicetree@vger.kernel.org --- .../devicetree/bindings/media/atmel-isi.txt | 51 ++++++++++++++++++++ drivers/media/platform/soc_camera/atmel-isi.c | 33 ++++++++++++- 2 files changed, 82 insertions(+), 2 deletions(-) create mode 100644 Documentation/devicetree/bindings/media/atmel-isi.txt diff --git a/Documentation/devicetree/bindings/media/atmel-isi.txt b/Documentation/devicetree/bindings/media/atmel-isi.txt new file mode 100644 index 0000000..07f00eb --- /dev/null +++ b/Documentation/devicetree/bindings/media/atmel-isi.txt @@ -0,0 +1,51 @@ +Atmel Image Sensor Interface (ISI) SoC Camera Subsystem +---------------------------------------------- + +Required properties: +- compatible: must be "atmel,at91sam9g45-isi" +- reg: physical base address and length of the registers set for the device; +- interrupts: should contain IRQ line for the ISI; +- clocks: list of clock specifiers, corresponding to entries in + the clock-names property; +- clock-names: must contain "isi_clk", which is the isi peripherial clock. + "isi_mck" is optinal, it is the master clock output to sensor. + +Optional properties: +- atmel,isi-disable-preview: a boolean property to disable the preview channel; + +Example: + isi: isi@f0034000 { + compatible = "atmel,at91sam9g45-isi"; + reg = <0xf0034000 0x4000>; + interrupts = <37 IRQ_TYPE_LEVEL_HIGH 5>; + + clocks = <&isi_clk>, <&pck1>; + clock-names = "isi_clk", "isi_mck"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_isi &pinctrl_pck1_as_isi_mck>; + + port { + #address-cells = <1>; + #size-cells = <0>; + + isi_0: endpoint { + remote-endpoint = <&ov2640_0>; + }; + }; + }; + + i2c1: i2c@f0018000 { + ov2640: camera@0x30 { + compatible = "omnivision,ov2640"; + reg = <0x30>; + + port { + ov2640_0: endpoint { + remote-endpoint = <&isi_0>; + bus-width = <8>; + }; + }; + }; + }; + diff --git a/drivers/media/platform/soc_camera/atmel-isi.c b/drivers/media/platform/soc_camera/atmel-isi.c index 93bf1cb..1822129 100644 --- a/drivers/media/platform/soc_camera/atmel-isi.c +++ b/drivers/media/platform/soc_camera/atmel-isi.c @@ -19,6 +19,7 @@ #include <linux/interrupt.h> #include <linux/kernel.h> #include <linux/module.h> +#include <linux/of.h> #include <linux/platform_device.h> #include <linux/slab.h> @@ -33,6 +34,7 @@ #define VID_LIMIT_BYTES (16 * 1024 * 1024) #define MIN_FRAME_RATE 15 #define FRAME_INTERVAL_MILLI_SEC (1000 / MIN_FRAME_RATE) +#define ISI_DEFAULT_MCLK_FREQ 25000000 /* Frame buffer descriptor */ struct fbd { @@ -878,6 +880,22 @@ static int atmel_isi_remove(struct platform_device *pdev) return 0; } +static int atmel_isi_probe_dt(struct atmel_isi *isi, + struct platform_device *pdev) +{ + struct device_node *node = pdev->dev.of_node; + + isi->pdata.full_mode = !of_property_read_bool(node, + "atmel,isi-disable-preview"); + + /* Default settings for ISI */ + isi->pdata.mck_hz = ISI_DEFAULT_MCLK_FREQ; + isi->pdata.frate = ISI_CFG1_FRATE_CAPTURE_ALL; + isi->pdata.data_width_flags = ISI_DATAWIDTH_8 | ISI_DATAWIDTH_10; + + return 0; +} + static int atmel_isi_probe(struct platform_device *pdev) { unsigned int irq; @@ -889,7 +907,7 @@ static int atmel_isi_probe(struct platform_device *pdev) struct isi_platform_data *pdata; pdata = dev->platform_data; - if (!pdata || !pdata->data_width_flags) { + if ((!pdata || !pdata->data_width_flags) && !pdev->dev.of_node) { dev_err(&pdev->dev, "No config available for Atmel ISI\n"); return -EINVAL; @@ -905,7 +923,11 @@ static int atmel_isi_probe(struct platform_device *pdev) if (IS_ERR(isi->pclk)) return PTR_ERR(isi->pclk); - memcpy(&isi->pdata, pdata, sizeof(struct isi_platform_data)); + if (pdata) + memcpy(&isi->pdata, pdata, sizeof(struct isi_platform_data)); + else /* dt probe */ + atmel_isi_probe_dt(isi, pdev); + isi->active = NULL; spin_lock_init(&isi->lock); INIT_LIST_HEAD(&isi->video_buffer_list); @@ -1007,11 +1029,18 @@ err_alloc_ctx: return ret; } +static const struct of_device_id atmel_isi_of_match[] = { + { .compatible = "atmel,at91sam9g45-isi" }, + { } +}; +MODULE_DEVICE_TABLE(of, atmel_isi_of_match); + static struct platform_driver atmel_isi_driver = { .remove = atmel_isi_remove, .driver = { .name = "atmel_isi", .owner = THIS_MODULE, + .of_match_table = atmel_isi_of_match, }, }; -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH 3/3] [media] atmel-isi: add primary DT support 2014-03-18 11:19 ` [PATCH 3/3] [media] atmel-isi: add primary DT support Josh Wu @ 2014-03-18 13:36 ` Laurent Pinchart 2014-03-19 9:15 ` Josh Wu 0 siblings, 1 reply; 4+ messages in thread From: Laurent Pinchart @ 2014-03-18 13:36 UTC (permalink / raw) To: Josh Wu Cc: g.liakhovetski, linux-media, m.chehab, nicolas.ferre, linux-arm-kernel, grant.likely, galak, rob, mark.rutland, robh+dt, ijc+devicetree, pawel.moll, devicetree Hi Josh, Thank you for the patch. On Tuesday 18 March 2014 19:19:54 Josh Wu wrote: > This patch add the DT support for Atmel ISI driver. > It use the same v4l2 DT interface that defined in video-interfaces.txt. > > Signed-off-by: Josh Wu <josh.wu@atmel.com> > Cc: devicetree@vger.kernel.org > --- > .../devicetree/bindings/media/atmel-isi.txt | 51 +++++++++++++++++ > drivers/media/platform/soc_camera/atmel-isi.c | 33 ++++++++++++- > 2 files changed, 82 insertions(+), 2 deletions(-) > create mode 100644 Documentation/devicetree/bindings/media/atmel-isi.txt > > diff --git a/Documentation/devicetree/bindings/media/atmel-isi.txt > b/Documentation/devicetree/bindings/media/atmel-isi.txt new file mode > 100644 > index 0000000..07f00eb > --- /dev/null > +++ b/Documentation/devicetree/bindings/media/atmel-isi.txt > @@ -0,0 +1,51 @@ > +Atmel Image Sensor Interface (ISI) SoC Camera Subsystem > +---------------------------------------------- > + > +Required properties: > +- compatible: must be "atmel,at91sam9g45-isi" > +- reg: physical base address and length of the registers set for the > device; > +- interrupts: should contain IRQ line for the ISI; > +- clocks: list of clock specifiers, corresponding to entries in > + the clock-names property; > +- clock-names: must contain "isi_clk", which is the isi peripherial clock. > + "isi_mck" is optinal, it is the master clock output to > sensor. The mck clock should be handled by the sensor driver instead. I know we have a legacy mode in the atmel-isi driver to manage that clock internally, but let's not propagate that to DT. I would also drop the "isi_" prefix from the isi_clk name. You should also describe the port node. You can just mention the related bindings document, and state that the ISI has a single port. > +Optional properties: > +- atmel,isi-disable-preview: a boolean property to disable the preview > channel; That doesn't really sound like a hardware property to me. Isn't it full mode related to software configuration instead, which should be performed at runtime by userspace ? > + > +Example: > + isi: isi@f0034000 { > + compatible = "atmel,at91sam9g45-isi"; > + reg = <0xf0034000 0x4000>; > + interrupts = <37 IRQ_TYPE_LEVEL_HIGH 5>; > + > + clocks = <&isi_clk>, <&pck1>; > + clock-names = "isi_clk", "isi_mck"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_isi &pinctrl_pck1_as_isi_mck>; > + > + port { > + #address-cells = <1>; > + #size-cells = <0>; > + > + isi_0: endpoint { > + remote-endpoint = <&ov2640_0>; > + }; > + }; > + }; > + > + i2c1: i2c@f0018000 { > + ov2640: camera@0x30 { > + compatible = "omnivision,ov2640"; > + reg = <0x30>; > + > + port { > + ov2640_0: endpoint { > + remote-endpoint = <&isi_0>; > + bus-width = <8>; > + }; > + }; > + }; > + }; > + > diff --git a/drivers/media/platform/soc_camera/atmel-isi.c > b/drivers/media/platform/soc_camera/atmel-isi.c index 93bf1cb..1822129 > 100644 > --- a/drivers/media/platform/soc_camera/atmel-isi.c > +++ b/drivers/media/platform/soc_camera/atmel-isi.c > @@ -19,6 +19,7 @@ > #include <linux/interrupt.h> > #include <linux/kernel.h> > #include <linux/module.h> > +#include <linux/of.h> > #include <linux/platform_device.h> > #include <linux/slab.h> > > @@ -33,6 +34,7 @@ > #define VID_LIMIT_BYTES (16 * 1024 * 1024) > #define MIN_FRAME_RATE 15 > #define FRAME_INTERVAL_MILLI_SEC (1000 / MIN_FRAME_RATE) > +#define ISI_DEFAULT_MCLK_FREQ 25000000 > > /* Frame buffer descriptor */ > struct fbd { > @@ -878,6 +880,22 @@ static int atmel_isi_remove(struct platform_device > *pdev) return 0; > } > > +static int atmel_isi_probe_dt(struct atmel_isi *isi, > + struct platform_device *pdev) > +{ > + struct device_node *node = pdev->dev.of_node; > + > + isi->pdata.full_mode = !of_property_read_bool(node, > + "atmel,isi-disable-preview"); > + > + /* Default settings for ISI */ > + isi->pdata.mck_hz = ISI_DEFAULT_MCLK_FREQ; > + isi->pdata.frate = ISI_CFG1_FRATE_CAPTURE_ALL; > + isi->pdata.data_width_flags = ISI_DATAWIDTH_8 | ISI_DATAWIDTH_10; > + > + return 0; > +} > + > static int atmel_isi_probe(struct platform_device *pdev) > { > unsigned int irq; > @@ -889,7 +907,7 @@ static int atmel_isi_probe(struct platform_device *pdev) > struct isi_platform_data *pdata; > > pdata = dev->platform_data; > - if (!pdata || !pdata->data_width_flags) { > + if ((!pdata || !pdata->data_width_flags) && !pdev->dev.of_node) { > dev_err(&pdev->dev, > "No config available for Atmel ISI\n"); > return -EINVAL; > @@ -905,7 +923,11 @@ static int atmel_isi_probe(struct platform_device > *pdev) if (IS_ERR(isi->pclk)) > return PTR_ERR(isi->pclk); > > - memcpy(&isi->pdata, pdata, sizeof(struct isi_platform_data)); > + if (pdata) > + memcpy(&isi->pdata, pdata, sizeof(struct isi_platform_data)); > + else /* dt probe */ > + atmel_isi_probe_dt(isi, pdev); > + > isi->active = NULL; > spin_lock_init(&isi->lock); > INIT_LIST_HEAD(&isi->video_buffer_list); > @@ -1007,11 +1029,18 @@ err_alloc_ctx: > return ret; > } > > +static const struct of_device_id atmel_isi_of_match[] = { > + { .compatible = "atmel,at91sam9g45-isi" }, > + { } > +}; > +MODULE_DEVICE_TABLE(of, atmel_isi_of_match); > + > static struct platform_driver atmel_isi_driver = { > .remove = atmel_isi_remove, > .driver = { > .name = "atmel_isi", > .owner = THIS_MODULE, > + .of_match_table = atmel_isi_of_match, > }, > }; -- Regards, Laurent Pinchart ^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH 3/3] [media] atmel-isi: add primary DT support 2014-03-18 13:36 ` Laurent Pinchart @ 2014-03-19 9:15 ` Josh Wu 2014-03-19 10:28 ` Laurent Pinchart 0 siblings, 1 reply; 4+ messages in thread From: Josh Wu @ 2014-03-19 9:15 UTC (permalink / raw) To: Laurent Pinchart Cc: g.liakhovetski, linux-media, m.chehab, nicolas.ferre, linux-arm-kernel, grant.likely, galak, rob, mark.rutland, robh+dt, ijc+devicetree, pawel.moll, devicetree Hi, Laurent On 3/18/2014 9:36 PM, Laurent Pinchart wrote: > Hi Josh, > > Thank you for the patch. Thanks for your review. > > On Tuesday 18 March 2014 19:19:54 Josh Wu wrote: >> This patch add the DT support for Atmel ISI driver. >> It use the same v4l2 DT interface that defined in video-interfaces.txt. >> >> Signed-off-by: Josh Wu <josh.wu@atmel.com> >> Cc: devicetree@vger.kernel.org >> --- >> .../devicetree/bindings/media/atmel-isi.txt | 51 +++++++++++++++++ >> drivers/media/platform/soc_camera/atmel-isi.c | 33 ++++++++++++- >> 2 files changed, 82 insertions(+), 2 deletions(-) >> create mode 100644 Documentation/devicetree/bindings/media/atmel-isi.txt >> >> diff --git a/Documentation/devicetree/bindings/media/atmel-isi.txt >> b/Documentation/devicetree/bindings/media/atmel-isi.txt new file mode >> 100644 >> index 0000000..07f00eb >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/media/atmel-isi.txt >> @@ -0,0 +1,51 @@ >> +Atmel Image Sensor Interface (ISI) SoC Camera Subsystem >> +---------------------------------------------- >> + >> +Required properties: >> +- compatible: must be "atmel,at91sam9g45-isi" >> +- reg: physical base address and length of the registers set for the >> device; >> +- interrupts: should contain IRQ line for the ISI; >> +- clocks: list of clock specifiers, corresponding to entries in >> + the clock-names property; >> +- clock-names: must contain "isi_clk", which is the isi peripherial clock. >> + "isi_mck" is optinal, it is the master clock output to >> sensor. > The mck clock should be handled by the sensor driver instead. I know we have a > legacy mode in the atmel-isi driver to manage that clock internally, but let's > not propagate that to DT. I agree with you. I put the isi_mck as optional here because current the sensor driver code only managed the v4l2 clock not the common clock. There should add additional code to manager mck clock. So if you want to ISI work for now, you should put the isi_mck in atmel-isi DT node. But for sure I can remove the isi_mck in atmel-isi DT document. In the future it will be add in sensor's DT document. > I would also drop the "isi_" prefix from the isi_clk > name. hmm, I think "isi_clk" indicates it is a ISI peripheral clock. And which is consistent with other peripheral clock name in sama5. > > You should also describe the port node. You can just mention the related > bindings document, and state that the ISI has a single port. OK. will add in the v2. > >> +Optional properties: >> +- atmel,isi-disable-preview: a boolean property to disable the preview >> channel; > That doesn't really sound like a hardware property to me. Isn't it full mode > related to software configuration instead, which should be performed at > runtime by userspace ? yes, this configuration can be disable/enable by driver according to user select format. I will remove it in v2. Thanks. Best Regards, Josh Wu > >> + >> +Example: >> + isi: isi@f0034000 { >> + compatible = "atmel,at91sam9g45-isi"; >> + reg = <0xf0034000 0x4000>; >> + interrupts = <37 IRQ_TYPE_LEVEL_HIGH 5>; >> + >> + clocks = <&isi_clk>, <&pck1>; >> + clock-names = "isi_clk", "isi_mck"; >> + >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_isi &pinctrl_pck1_as_isi_mck>; >> + >> + port { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + isi_0: endpoint { >> + remote-endpoint = <&ov2640_0>; >> + }; >> + }; >> + }; >> + >> + i2c1: i2c@f0018000 { >> + ov2640: camera@0x30 { >> + compatible = "omnivision,ov2640"; >> + reg = <0x30>; >> + >> + port { >> + ov2640_0: endpoint { >> + remote-endpoint = <&isi_0>; >> + bus-width = <8>; >> + }; >> + }; >> + }; >> + }; >> + >> diff --git a/drivers/media/platform/soc_camera/atmel-isi.c >> b/drivers/media/platform/soc_camera/atmel-isi.c index 93bf1cb..1822129 >> 100644 >> --- a/drivers/media/platform/soc_camera/atmel-isi.c >> +++ b/drivers/media/platform/soc_camera/atmel-isi.c >> @@ -19,6 +19,7 @@ >> #include <linux/interrupt.h> >> #include <linux/kernel.h> >> #include <linux/module.h> >> +#include <linux/of.h> >> #include <linux/platform_device.h> >> #include <linux/slab.h> >> >> @@ -33,6 +34,7 @@ >> #define VID_LIMIT_BYTES (16 * 1024 * 1024) >> #define MIN_FRAME_RATE 15 >> #define FRAME_INTERVAL_MILLI_SEC (1000 / MIN_FRAME_RATE) >> +#define ISI_DEFAULT_MCLK_FREQ 25000000 >> >> /* Frame buffer descriptor */ >> struct fbd { >> @@ -878,6 +880,22 @@ static int atmel_isi_remove(struct platform_device >> *pdev) return 0; >> } >> >> +static int atmel_isi_probe_dt(struct atmel_isi *isi, >> + struct platform_device *pdev) >> +{ >> + struct device_node *node = pdev->dev.of_node; >> + >> + isi->pdata.full_mode = !of_property_read_bool(node, >> + "atmel,isi-disable-preview"); >> + >> + /* Default settings for ISI */ >> + isi->pdata.mck_hz = ISI_DEFAULT_MCLK_FREQ; >> + isi->pdata.frate = ISI_CFG1_FRATE_CAPTURE_ALL; >> + isi->pdata.data_width_flags = ISI_DATAWIDTH_8 | ISI_DATAWIDTH_10; >> + >> + return 0; >> +} >> + >> static int atmel_isi_probe(struct platform_device *pdev) >> { >> unsigned int irq; >> @@ -889,7 +907,7 @@ static int atmel_isi_probe(struct platform_device *pdev) >> struct isi_platform_data *pdata; >> >> pdata = dev->platform_data; >> - if (!pdata || !pdata->data_width_flags) { >> + if ((!pdata || !pdata->data_width_flags) && !pdev->dev.of_node) { >> dev_err(&pdev->dev, >> "No config available for Atmel ISI\n"); >> return -EINVAL; >> @@ -905,7 +923,11 @@ static int atmel_isi_probe(struct platform_device >> *pdev) if (IS_ERR(isi->pclk)) >> return PTR_ERR(isi->pclk); >> >> - memcpy(&isi->pdata, pdata, sizeof(struct isi_platform_data)); >> + if (pdata) >> + memcpy(&isi->pdata, pdata, sizeof(struct isi_platform_data)); >> + else /* dt probe */ >> + atmel_isi_probe_dt(isi, pdev); >> + >> isi->active = NULL; >> spin_lock_init(&isi->lock); >> INIT_LIST_HEAD(&isi->video_buffer_list); >> @@ -1007,11 +1029,18 @@ err_alloc_ctx: >> return ret; >> } >> >> +static const struct of_device_id atmel_isi_of_match[] = { >> + { .compatible = "atmel,at91sam9g45-isi" }, >> + { } >> +}; >> +MODULE_DEVICE_TABLE(of, atmel_isi_of_match); >> + >> static struct platform_driver atmel_isi_driver = { >> .remove = atmel_isi_remove, >> .driver = { >> .name = "atmel_isi", >> .owner = THIS_MODULE, >> + .of_match_table = atmel_isi_of_match, >> }, >> }; ^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH 3/3] [media] atmel-isi: add primary DT support 2014-03-19 9:15 ` Josh Wu @ 2014-03-19 10:28 ` Laurent Pinchart 0 siblings, 0 replies; 4+ messages in thread From: Laurent Pinchart @ 2014-03-19 10:28 UTC (permalink / raw) To: Josh Wu Cc: g.liakhovetski, linux-media, m.chehab, nicolas.ferre, linux-arm-kernel, grant.likely, galak, rob, mark.rutland, robh+dt, ijc+devicetree, pawel.moll, devicetree Hi Josh, On Wednesday 19 March 2014 17:15:02 Josh Wu wrote: > On 3/18/2014 9:36 PM, Laurent Pinchart wrote: > > On Tuesday 18 March 2014 19:19:54 Josh Wu wrote: > >> This patch add the DT support for Atmel ISI driver. > >> It use the same v4l2 DT interface that defined in video-interfaces.txt. > >> > >> Signed-off-by: Josh Wu <josh.wu@atmel.com> > >> Cc: devicetree@vger.kernel.org > >> --- > >> > >> .../devicetree/bindings/media/atmel-isi.txt | 51 ++++++++++++++ > >> drivers/media/platform/soc_camera/atmel-isi.c | 33 ++++++++++++- > >> 2 files changed, 82 insertions(+), 2 deletions(-) > >> create mode 100644 > >> Documentation/devicetree/bindings/media/atmel-isi.txt > >> > >> diff --git a/Documentation/devicetree/bindings/media/atmel-isi.txt > >> b/Documentation/devicetree/bindings/media/atmel-isi.txt new file mode > >> 100644 > >> index 0000000..07f00eb > >> --- /dev/null > >> +++ b/Documentation/devicetree/bindings/media/atmel-isi.txt > >> @@ -0,0 +1,51 @@ > >> +Atmel Image Sensor Interface (ISI) SoC Camera Subsystem > >> +---------------------------------------------- > >> + > >> +Required properties: > >> +- compatible: must be "atmel,at91sam9g45-isi" > >> +- reg: physical base address and length of the registers set for the > >> device; > >> +- interrupts: should contain IRQ line for the ISI; > >> +- clocks: list of clock specifiers, corresponding to entries in > >> + the clock-names property; > >> +- clock-names: must contain "isi_clk", which is the isi peripherial > >> clock. > >> + "isi_mck" is optinal, it is the master clock output to > >> sensor. > > > > The mck clock should be handled by the sensor driver instead. I know we > > have a legacy mode in the atmel-isi driver to manage that clock > > internally, but let's not propagate that to DT. > > I agree with you. > > I put the isi_mck as optional here because current the sensor driver > code only managed the v4l2 clock not the common clock. > There should add additional code to manager mck clock. > So if you want to ISI work for now, you should put the isi_mck in > atmel-isi DT node. > > But for sure I can remove the isi_mck in atmel-isi DT document. In the > future it will be add in sensor's DT document. I think that's the way to go, yes. I know we have existing platforms that require sensor clock management in the ISI driver. That should be fixed, and a move to DT is a perfect opportunity to do so :-) > > I would also drop the "isi_" prefix from the isi_clk name. > > hmm, I think "isi_clk" indicates it is a ISI peripheral clock. And > which is consistent with other peripheral clock name in sama5. I believe the "isi_" prefix is redundant, given that the clock-names property is inside the ISI DT node. However, if this style matches the rest of the platform there's no need to change it. > > You should also describe the port node. You can just mention the related > > bindings document, and state that the ISI has a single port. > > OK. will add in the v2. > > >> +Optional properties: > >> +- atmel,isi-disable-preview: a boolean property to disable the preview > >> channel; > > > > That doesn't really sound like a hardware property to me. Isn't it full > > mode related to software configuration instead, which should be performed > > at runtime by userspace ? > > yes, this configuration can be disable/enable by driver according to > user select format. > I will remove it in v2. Thanks. > > Best Regards, > Josh Wu > > >> + > >> +Example: > >> + isi: isi@f0034000 { > >> + compatible = "atmel,at91sam9g45-isi"; > >> + reg = <0xf0034000 0x4000>; > >> + interrupts = <37 IRQ_TYPE_LEVEL_HIGH 5>; > >> + > >> + clocks = <&isi_clk>, <&pck1>; > >> + clock-names = "isi_clk", "isi_mck"; > >> + > >> + pinctrl-names = "default"; > >> + pinctrl-0 = <&pinctrl_isi &pinctrl_pck1_as_isi_mck>; > >> + > >> + port { > >> + #address-cells = <1>; > >> + #size-cells = <0>; > >> + > >> + isi_0: endpoint { > >> + remote-endpoint = <&ov2640_0>; > >> + }; > >> + }; > >> + }; > >> + > >> + i2c1: i2c@f0018000 { > >> + ov2640: camera@0x30 { > >> + compatible = "omnivision,ov2640"; > >> + reg = <0x30>; > >> + > >> + port { > >> + ov2640_0: endpoint { > >> + remote-endpoint = <&isi_0>; > >> + bus-width = <8>; > >> + }; > >> + }; > >> + }; > >> + }; -- Regards, Laurent Pinchart ^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2014-03-19 10:28 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <1395141238-5948-1-git-send-email-josh.wu@atmel.com>
2014-03-18 11:19 ` [PATCH 3/3] [media] atmel-isi: add primary DT support Josh Wu
2014-03-18 13:36 ` Laurent Pinchart
2014-03-19 9:15 ` Josh Wu
2014-03-19 10:28 ` Laurent Pinchart
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).