Re: [PATCH 02/10] arm64: dts: qcom: sm6350: Add pinctrl for SDHCI 2

[Konrad Dybcio <konrad.dybcio@somainline.org>]

On 30.10.2022 08:32, Marijn Suijten wrote:
> Use the generic pin functions specifically for sdc2.
> 
> Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>

Konrad
>  arch/arm64/boot/dts/qcom/sm6350.dtsi | 44 ++++++++++++++++++++++++++++
>  1 file changed, 44 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
> index a3ae765d9781..b98b881ebe7e 100644
> --- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
> @@ -1074,6 +1074,10 @@ sdhc_2: mmc@8804000 {
>  					<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_SDCC_2 0>;
>  			interconnect-names = "sdhc-ddr", "cpu-sdhc";
>  
> +			pinctrl-0 = <&sdc2_on_state>;
> +			pinctrl-1 = <&sdc2_off_state>;
> +			pinctrl-names = "default", "sleep";
> +
>  			qcom,dll-config = <0x0007642c>;
>  			qcom,ddr-config = <0x80040868>;
>  			power-domains = <&rpmhpd SM6350_CX>;
> @@ -1316,6 +1320,46 @@ tlmm: pinctrl@f100000 {
>  			#interrupt-cells = <2>;
>  			gpio-ranges = <&tlmm 0 0 157>;
>  
> +			sdc2_off_state: sdc2-off-state {
> +				clk-pins {
> +					pins = "sdc2_clk";
> +					drive-strength = <2>;
> +					bias-disable;
> +				};
> +
> +				cmd-pins {
> +					pins = "sdc2_cmd";
> +					drive-strength = <2>;
> +					bias-pull-up;
> +				};
> +
> +				data-pins {
> +					pins = "sdc2_data";
> +					drive-strength = <2>;
> +					bias-pull-up;
> +				};
> +			};
> +
> +			sdc2_on_state: sdc2-on-state {
> +				clk-pins {
> +					pins = "sdc2_clk";
> +					drive-strength = <16>;
> +					bias-disable;
> +				};
> +
> +				cmd-pins {
> +					pins = "sdc2_cmd";
> +					drive-strength = <10>;
> +					bias-pull-up;
> +				};
> +
> +				data-pins {
> +					pins = "sdc2_data";
> +					drive-strength = <10>;
> +					bias-pull-up;
> +				};
> +			};
> +
>  			qup_uart9_default: qup-uart9-default-state {
>  				pins = "gpio25", "gpio26";
>  				function = "qup13_f2";