[PATCH v8 00/16] media: qcom: camss: Add sm8550 support

[PATCH v8 00/16] media: qcom: camss: Add sm8550 support

[Depeng Shao]

v8:
- Add correct version number for each patch - Krzysztof, Hans, Bryan
- Correct the copyright in patches [15/16] and [16/16]
- Link to v7: https://lore.kernel.org/all/20241225133523.4034820-1-quic_depengs@quicinc.com/

v7:
- Due to the patches in https://lore.kernel.org/all/20241217140656.965235-1-quic_vikramsa@quicinc.com/
  are merged, so rebased below patches to fix the conflict.
  media: qcom: camss: csiphy-3ph: Remove redundant PHY init sequence control loop
  media: qcom: camss: csiphy-3ph: Move CSIPHY variables to data field inside csiphy struct
  media: qcom: camss: Add sm8550 compatible
  media: qcom: camss: csiphy-3ph: Move CSIPHY variables to data field inside csiphy struct
  media: qcom: camss: csiphy-3ph: Add Gen2 v2.1.2 two-phase MIPI CSI-2 DPHY support
  media: qcom: camss: Add support for VFE 780
- Add RB for "media: qcom: camss: Add CSID 780 support" - Bryan
- Use TAG name for ICC and remove offline HW ICC - Bryan
- Remove the logic that moving enable_irq();/disable_irq(); to wm_start() 
  and wm_stop() to make sure no logical change in VFE refactor change.
- Update the commit message and title for the TPG change. - Bryan
- Link to v6: https://lore.kernel.org/all/20241211140738.3835588-1-quic_depengs@quicinc.com/

v6:
- Add bus type property in dt-binding which will be limited
  by a latest change 
  https://lore.kernel.org/all/20241209-camss-dphy-v1-0-5f1b6f25ed92@fairphone.com/
- Add RB for "media: qcom: camss: Add sm8550 compatible" and
  "media: qcom: camss: Add support for VFE 780"
- Uppercase the hex in csiphy register list - Bryan
- Add empty function for csid tpg - Vladimir
- Set testgen mode to CSID_PAYLOAD_MODE_DISABLED in subdev init interface
- encapsulate the guard __thus__ for new header - Bryan
- Add a standalone patch for the platform which doesn't support CSID TPG
  to make sure new platform driver can set CSID_PAYLOAD_MODE_DISABLED
  to disable TPG
- Update the csid for csid and vfe driver - Bryan
- Link to v5: https://lore.kernel.org/all/20241205155538.250743-1-quic_depengs@quicinc.com/

v5:
- Update dt-bindings required items order - Krzysztof
- Sort the reg order based on the comments in sc7280 dt-binding - Vladimir
- Change the irq type to IRQ_TYPE_EDGE_RISING - Vladimir
- Remove the Krzysztof's RB tag from dt-binding patch due to above
  updates in dt-binding patch
- Move regulator from csid resource to csiphy resource - Bryan, Vladimir
- Move the change to add default case in vfe_src_pad_code to a
  standalone patch. - Bryan
- Rename csid-gen3 as csid-780 - Bryan
- use macros() to bury bit shifts - Bryan
- Sort the macros by register offset order  -  Vladimir
- Redefine a macro for rup_aup in csid driver - Vladimir
- Remove the unused macros in vfe 780 driver - Vladimir
- Add dummy function for unsupported hw_ops in vfe 780
  driver - Vladimir, Bryan
- Use a standalone patch for the callback API of RUP and buf done update
- Use a standalone patch to make CSID TPG optional - Vladimir
- Link to v4: https://lore.kernel.org/all/20240812144131.369378-1-quic_depengs@quicinc.com/

v4:
- Update dt-bindings based on comments - Krzysztof, bod, Vladimir
- Move common code into csid core and vfe core driver - bod
- Remove *_relaxed in the csid and vfe drivers - Krzysztof
- Reorganize patches in logical junks, make sure that new added
structures have users in current patch - Krzysztof
- Remove notify function  and add new functions in camss for buf done
and reg update - bod
- Remove custom code to get csid base - bod
- Remove ISR function in vfe780 driver since it is never fired - bod
- Move csid_top_base to camss structure since we only have one csid
top block, and just need to get base once for csid top
- Add Vladimir's RB
- Remove prerequisite-patch-id in the cover letter since the changes
have been merged
- Add dtsi patch link for reference - Krzysztof
https://lore.kernel.org/all/20240807123333.2056518-1-quic_depengs@quicinc.com/
- Link to v3: https://lore.kernel.org/all/20240709160656.31146-1-quic_depengs@quicinc.com/

v3:
- Rebased the change based on below change which will be merged firstly.
"Move camss version related defs in to resources"
Link: https://lore.kernel.org/all/20240522154659.510-1-quic_grosikop@quicinc.com/
- Rebased the change based on Bryan's csiphy optimization change and add
these changes into this series, so that the new csiphy-3ph driver don't
need to add duplicate code. This has got Bryan's permission to add his
patches into this series.
- Refactor some changes based on the comments to move the random code to
patches where they are used.
- Remove the vfe780 irq function since it isn't doing the actual work.
- Add dt-binding for sm8550 camss driver.
Link to V2: https://lore.kernel.org/all/20240320141136.26827-1-quic_depengs@quicinc.com/

v2:
- Update some commit messages
Link to V1: https://lore.kernel.org/all/20240320134227.16587-1-quic_depengs@quicinc.com/

v1:
SM8550 is a Qualcomm flagship SoC. This series adds support to
bring up the CSIPHY, CSID, VFE/RDI interfaces in SM8550.

SM8550 provides

- 3 x VFE, 3 RDI per VFE
- 2 x VFE Lite, 4 RDI per VFE
- 3 x CSID
- 2 x CSID Lite
- 8 x CSI PHY

Bryan O'Donoghue (6):
  media: qcom: camss: csiphy-3ph: Fix trivial indentation fault in
    defines
  media: qcom: camss: csiphy-3ph: Remove redundant PHY init sequence
    control loop
  media: qcom: camss: csiphy-3ph: Rename struct
  media: qcom: camss: csiphy: Add an init callback to CSI PHY devices
  media: qcom: camss: csiphy-3ph: Move CSIPHY variables to data field
    inside csiphy struct
  media: qcom: camss: csiphy-3ph: Use an offset variable to find common
    control regs

Depeng Shao (10):
  media: qcom: camss: csid: Move common code into csid core
  media: qcom: camss: vfe: Move common code into vfe core
  media: qcom: camss: Add callback API for RUP update and buf done
  media: qcom: camss: Add default case in vfe_src_pad_code
  media: qcom: camss: csid: Only add TPG v4l2 ctrl if TPG hardware is
    available
  dt-bindings: media: camss: Add qcom,sm8550-camss binding
  media: qcom: camss: Add sm8550 compatible
  media: qcom: camss: csiphy-3ph: Add Gen2 v2.1.2 two-phase MIPI CSI-2
    DPHY support
  media: qcom: camss: Add CSID 780 support
  media: qcom: camss: Add support for VFE 780

 .../bindings/media/qcom,sm8550-camss.yaml     | 597 +++++++++++++
 drivers/media/platform/qcom/camss/Makefile    |   2 +
 .../platform/qcom/camss/camss-csid-4-1.c      |  19 -
 .../platform/qcom/camss/camss-csid-4-7.c      |  42 -
 .../platform/qcom/camss/camss-csid-780.c      | 337 ++++++++
 .../platform/qcom/camss/camss-csid-780.h      |  25 +
 .../platform/qcom/camss/camss-csid-gen2.c     |  60 --
 .../media/platform/qcom/camss/camss-csid.c    | 137 ++-
 .../media/platform/qcom/camss/camss-csid.h    |  31 +
 .../qcom/camss/camss-csiphy-2ph-1-0.c         |   6 +
 .../qcom/camss/camss-csiphy-3ph-1-0.c         | 794 ++++++++++--------
 .../media/platform/qcom/camss/camss-csiphy.c  |   4 +
 .../media/platform/qcom/camss/camss-csiphy.h  |   8 +
 .../media/platform/qcom/camss/camss-vfe-17x.c | 112 +--
 .../media/platform/qcom/camss/camss-vfe-4-1.c |   9 -
 .../media/platform/qcom/camss/camss-vfe-4-7.c |  11 -
 .../media/platform/qcom/camss/camss-vfe-4-8.c |  11 -
 .../media/platform/qcom/camss/camss-vfe-480.c | 274 +-----
 .../media/platform/qcom/camss/camss-vfe-780.c | 159 ++++
 drivers/media/platform/qcom/camss/camss-vfe.c | 274 ++++++
 drivers/media/platform/qcom/camss/camss-vfe.h |  59 +-
 drivers/media/platform/qcom/camss/camss.c     | 359 ++++++++
 drivers/media/platform/qcom/camss/camss.h     |   4 +
 23 files changed, 2464 insertions(+), 870 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/media/qcom,sm8550-camss.yaml
 create mode 100644 drivers/media/platform/qcom/camss/camss-csid-780.c
 create mode 100644 drivers/media/platform/qcom/camss/camss-csid-780.h
 create mode 100644 drivers/media/platform/qcom/camss/camss-vfe-780.c


base-commit: 8155b4ef3466f0e289e8fcc9e6e62f3f4dceeac2
-- 
2.34.1

[PATCH v8 01/16] media: qcom: camss: csiphy-3ph: Fix trivial indentation fault in defines

[Depeng Shao]

From: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

Replace space with tab in define indentations.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Depeng Shao <quic_depengs@quicinc.com>
Reviewed-by: Elliot Berman <quic_eberman@quicinc.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
---
 .../platform/qcom/camss/camss-csiphy-3ph-1-0.c     | 14 +++++++-------
 1 file changed, 7 insertions(+), 7 deletions(-)

diff --git a/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c b/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c
index f341f7b7fd8a..616a9aa73cec 100644
--- a/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c
+++ b/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c
@@ -48,13 +48,13 @@
 #define CSIPHY_3PH_CMN_CSI_COMMON_CTRL6_SHOW_REV_ID	BIT(1)
 #define CSIPHY_3PH_CMN_CSI_COMMON_STATUSn(n)	(0x8b0 + 0x4 * (n))
 
-#define CSIPHY_DEFAULT_PARAMS            0
-#define CSIPHY_LANE_ENABLE               1
-#define CSIPHY_SETTLE_CNT_LOWER_BYTE     2
-#define CSIPHY_SETTLE_CNT_HIGHER_BYTE    3
-#define CSIPHY_DNP_PARAMS                4
-#define CSIPHY_2PH_REGS                  5
-#define CSIPHY_3PH_REGS                  6
+#define CSIPHY_DEFAULT_PARAMS		0
+#define CSIPHY_LANE_ENABLE		1
+#define CSIPHY_SETTLE_CNT_LOWER_BYTE	2
+#define CSIPHY_SETTLE_CNT_HIGHER_BYTE	3
+#define CSIPHY_DNP_PARAMS		4
+#define CSIPHY_2PH_REGS			5
+#define CSIPHY_3PH_REGS			6
 
 struct csiphy_reg_t {
 	s32 reg_addr;
-- 
2.34.1

[PATCH v8 02/16] media: qcom: camss: csiphy-3ph: Remove redundant PHY init sequence control loop

[Depeng Shao]

From: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

Adding a new CSIPHY init sequence using downstream as a reference prompted
me to look at why we are splitting up the init sequence into chunks.

Right now we declare CSI PHY init sequences as an array of five equally
sized writes with a hard-coded control loop to iterate through each of the
five indexes. One bug in this model is that if you don't have an even
number of writes, you can't init the PHY as you wish.

In downstream the original code has something of the character
phy_init_seq[MAX_LANES][MAX_PARAMS] which in upstream we have translated
into phy_init_seq[5][SOME_NUMBER_OF_EQUAL_WRITES];

What the code does is take a pointer to the first index of the
r = &phy_init_seq[0][0]; and then literally does write(r, value); r++;

The controlling loop that hard-codes '5' in-lieu of MAX_LANES does no
special sleep, fabric-coherence sync or even a printk() to justify its
existence. Our compilers are optimising all of this away anyway so lets
drop.

Reduce the array declaration down to one flat aggregate init and let the
code just step through. As a happy side-effect we can then also handle
odd-number writes as the number of elements in the init sequence will no
longer have to be evenly divisible.

Reviewed-by: Elliot Berman <quic_eberman@quicinc.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Depeng Shao <quic_depengs@quicinc.com>
---
 .../qcom/camss/camss-csiphy-3ph-1-0.c         | 558 +++++++++---------
 1 file changed, 263 insertions(+), 295 deletions(-)

diff --git a/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c b/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c
index 616a9aa73cec..f7b851242aa5 100644
--- a/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c
+++ b/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c
@@ -65,287 +65,257 @@ struct csiphy_reg_t {
 
 /* GEN2 1.0 2PH */
 static const struct
-csiphy_reg_t lane_regs_sdm845[5][14] = {
-	{
-		{0x0004, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x002C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0034, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x001C, 0x0A, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0014, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0028, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x003C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0000, 0x91, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0008, 0x00, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
-		{0x000c, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x0010, 0x52, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0038, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0060, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0064, 0x7F, 0x00, CSIPHY_DEFAULT_PARAMS},
-	},
-	{
-		{0x0704, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x072C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0734, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x071C, 0x0A, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0714, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0728, 0x04, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x073C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0700, 0x80, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0708, 0x14, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
-		{0x070C, 0xA5, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0710, 0x52, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0738, 0x1F, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0760, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0764, 0x7F, 0x00, CSIPHY_DEFAULT_PARAMS},
-	},
-	{
-		{0x0204, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x022C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0234, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x021C, 0x0A, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0214, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0228, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x023C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0200, 0x91, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0208, 0x00, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
-		{0x020C, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x0210, 0x52, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0238, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0260, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0264, 0x7F, 0x00, CSIPHY_DEFAULT_PARAMS},
-	},
-	{
-		{0x0404, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x042C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0434, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x041C, 0x0A, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0414, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0428, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x043C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0400, 0x91, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0408, 0x00, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
-		{0x040C, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x0410, 0x52, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0438, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0460, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0464, 0x7F, 0x00, CSIPHY_DEFAULT_PARAMS},
-	},
-	{
-		{0x0604, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x062C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0634, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x061C, 0x0A, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0614, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0628, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x063C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0600, 0x91, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0608, 0x00, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
-		{0x060C, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x0610, 0x52, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0638, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0660, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0664, 0x7F, 0x00, CSIPHY_DEFAULT_PARAMS},
-	},
+csiphy_reg_t lane_regs_sdm845[] = {
+	{0x0004, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x002C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0034, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x001C, 0x0A, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0014, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0028, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x003C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0000, 0x91, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0008, 0x00, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{0x000c, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x0010, 0x52, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0038, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0060, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0064, 0x7F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0704, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x072C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0734, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x071C, 0x0A, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0714, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0728, 0x04, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x073C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0700, 0x80, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0708, 0x14, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{0x070C, 0xA5, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0710, 0x52, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0738, 0x1F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0760, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0764, 0x7F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0204, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x022C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0234, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x021C, 0x0A, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0214, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0228, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x023C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0200, 0x91, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0208, 0x00, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{0x020C, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x0210, 0x52, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0238, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0260, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0264, 0x7F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0404, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x042C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0434, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x041C, 0x0A, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0414, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0428, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x043C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0400, 0x91, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0408, 0x00, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{0x040C, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x0410, 0x52, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0438, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0460, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0464, 0x7F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0604, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x062C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0634, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x061C, 0x0A, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0614, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0628, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x063C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0600, 0x91, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0608, 0x00, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{0x060C, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x0610, 0x52, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0638, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0660, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0664, 0x7F, 0x00, CSIPHY_DEFAULT_PARAMS},
 };
 
 /* GEN2 1.1 2PH */
 static const struct
-csiphy_reg_t lane_regs_sc8280xp[5][14] = {
-	{
-		{0x0004, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x002C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0034, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x001C, 0x0A, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0014, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0028, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x003C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0000, 0x90, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0008, 0x0E, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
-		{0x000C, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x0010, 0x52, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0038, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0060, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0064, 0x7F, 0x00, CSIPHY_DEFAULT_PARAMS},
-	},
-	{
-		{0x0704, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x072C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0734, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x071C, 0x0A, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0714, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0728, 0x04, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x073C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0700, 0x80, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0708, 0x0E, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
-		{0x070C, 0xA5, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0710, 0x52, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0738, 0x1F, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0760, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0764, 0x7F, 0x00, CSIPHY_DEFAULT_PARAMS},
-	},
-	{
-		{0x0204, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x022C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0234, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x021C, 0x0A, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0214, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0228, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x023C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0200, 0x90, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0208, 0x0E, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
-		{0x020C, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x0210, 0x52, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0238, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0260, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0264, 0x7F, 0x00, CSIPHY_DEFAULT_PARAMS},
-	},
-	{
-		{0x0404, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x042C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0434, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x041C, 0x0A, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0414, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0428, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x043C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0400, 0x90, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0408, 0x0E, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
-		{0x040C, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x0410, 0x52, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0438, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0460, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0464, 0x7F, 0x00, CSIPHY_DEFAULT_PARAMS},
-	},
-	{
-		{0x0604, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x062C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0634, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x061C, 0x0A, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0614, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0628, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x063C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0600, 0x90, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0608, 0x0E, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
-		{0x060C, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x0610, 0x52, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0638, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0660, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0664, 0x7F, 0x00, CSIPHY_DEFAULT_PARAMS},
-	},
+csiphy_reg_t lane_regs_sc8280xp[] = {
+	{0x0004, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x002C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0034, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x001C, 0x0A, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0014, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0028, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x003C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0000, 0x90, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0008, 0x0E, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{0x000C, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x0010, 0x52, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0038, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0060, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0064, 0x7F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0704, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x072C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0734, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x071C, 0x0A, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0714, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0728, 0x04, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x073C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0700, 0x80, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0708, 0x0E, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{0x070C, 0xA5, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0710, 0x52, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0738, 0x1F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0760, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0764, 0x7F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0204, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x022C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0234, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x021C, 0x0A, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0214, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0228, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x023C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0200, 0x90, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0208, 0x0E, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{0x020C, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x0210, 0x52, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0238, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0260, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0264, 0x7F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0404, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x042C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0434, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x041C, 0x0A, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0414, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0428, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x043C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0400, 0x90, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0408, 0x0E, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{0x040C, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x0410, 0x52, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0438, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0460, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0464, 0x7F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0604, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x062C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0634, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x061C, 0x0A, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0614, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0628, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x063C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0600, 0x90, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0608, 0x0E, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{0x060C, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x0610, 0x52, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0638, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0660, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0664, 0x7F, 0x00, CSIPHY_DEFAULT_PARAMS},
 };
 
 /* GEN2 1.2.1 2PH */
 static const struct
-csiphy_reg_t lane_regs_sm8250[5][20] = {
-	{
-		{0x0030, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0900, 0x05, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0908, 0x10, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0904, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0904, 0x07, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0004, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x002C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0034, 0x07, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0010, 0x02, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x001C, 0x08, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x003C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0008, 0x10, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
-		{0x0000, 0x8D, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x000c, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x0038, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0014, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0028, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x0024, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x0800, 0x02, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0884, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
-	},
-	{
-		{0x0730, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0C80, 0x05, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0C88, 0x10, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0C84, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0C84, 0x07, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0704, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x072C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0734, 0x07, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0710, 0x02, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x071C, 0x08, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x073C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0708, 0x10, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
-		{0x0700, 0x80, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x070c, 0xA5, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0738, 0x1F, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0714, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0728, 0x04, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0724, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x0800, 0x02, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0884, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
-	},
-	{
-		{0x0230, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0A00, 0x05, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0A08, 0x10, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0A04, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0A04, 0x07, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0204, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x022C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0234, 0x07, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0210, 0x02, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x021C, 0x08, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x023C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0208, 0x10, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
-		{0x0200, 0x8D, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x020c, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x0238, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0214, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0228, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x0224, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x0800, 0x02, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0884, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
-	},
-	{
-		{0x0430, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0B00, 0x05, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0B08, 0x10, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0B04, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0B04, 0x07, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0404, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x042C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0434, 0x07, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0410, 0x02, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x041C, 0x08, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x043C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0408, 0x10, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
-		{0x0400, 0x8D, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x040c, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x0438, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0414, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0428, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x0424, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x0800, 0x02, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0884, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
-	},
-	{
-		{0x0630, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0C00, 0x05, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0C08, 0x10, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0C04, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0C04, 0x07, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0604, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x062C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0634, 0x07, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0610, 0x02, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x061C, 0x08, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x063C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0608, 0x10, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
-		{0x0600, 0x8D, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x060c, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x0638, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0614, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0628, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x0624, 0x00, 0x00, CSIPHY_DNP_PARAMS},
-		{0x0800, 0x02, 0x00, CSIPHY_DEFAULT_PARAMS},
-		{0x0884, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
-	},
+csiphy_reg_t lane_regs_sm8250[] = {
+	{0x0030, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0900, 0x05, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0908, 0x10, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0904, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0904, 0x07, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0004, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x002C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0034, 0x07, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0010, 0x02, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x001C, 0x08, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x003C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0008, 0x10, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{0x0000, 0x8D, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x000c, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x0038, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0014, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0028, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x0024, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x0800, 0x02, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0884, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0730, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0C80, 0x05, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0C88, 0x10, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0C84, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0C84, 0x07, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0704, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x072C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0734, 0x07, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0710, 0x02, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x071C, 0x08, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x073C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0708, 0x10, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{0x0700, 0x80, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x070c, 0xA5, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0738, 0x1F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0714, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0728, 0x04, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0724, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x0800, 0x02, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0884, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0230, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0A00, 0x05, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0A08, 0x10, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0A04, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0A04, 0x07, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0204, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x022C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0234, 0x07, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0210, 0x02, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x021C, 0x08, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x023C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0208, 0x10, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{0x0200, 0x8D, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x020c, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x0238, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0214, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0228, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x0224, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x0800, 0x02, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0884, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0430, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0B00, 0x05, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0B08, 0x10, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0B04, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0B04, 0x07, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0404, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x042C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0434, 0x07, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0410, 0x02, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x041C, 0x08, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x043C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0408, 0x10, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{0x0400, 0x8D, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x040c, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x0438, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0414, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0428, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x0424, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x0800, 0x02, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0884, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0630, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0C00, 0x05, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0C08, 0x10, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0C04, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0C04, 0x07, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0604, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x062C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0634, 0x07, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0610, 0x02, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x061C, 0x08, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x063C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0608, 0x10, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{0x0600, 0x8D, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x060c, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x0638, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0614, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0628, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x0624, 0x00, 0x00, CSIPHY_DNP_PARAMS},
+	{0x0800, 0x02, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0884, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
 };
 
 static void csiphy_hw_version_read(struct csiphy_device *csiphy,
@@ -501,45 +471,43 @@ static void csiphy_gen2_config_lanes(struct csiphy_device *csiphy,
 				     u8 settle_cnt)
 {
 	const struct csiphy_reg_t *r;
-	int i, l, array_size;
+	int i, array_size;
 	u32 val;
 
 	switch (csiphy->camss->res->version) {
 	case CAMSS_7280:
-		r = &lane_regs_sm8250[0][0];
-		array_size = ARRAY_SIZE(lane_regs_sm8250[0]);
+		r = &lane_regs_sm8250[0];
+		array_size = ARRAY_SIZE(lane_regs_sm8250);
 		break;
 	case CAMSS_8250:
-		r = &lane_regs_sm8250[0][0];
-		array_size = ARRAY_SIZE(lane_regs_sm8250[0]);
+		r = &lane_regs_sm8250[0];
+		array_size = ARRAY_SIZE(lane_regs_sm8250);
 		break;
 	case CAMSS_8280XP:
-		r = &lane_regs_sc8280xp[0][0];
-		array_size = ARRAY_SIZE(lane_regs_sc8280xp[0]);
+		r = &lane_regs_sc8280xp[0];
+		array_size = ARRAY_SIZE(lane_regs_sc8280xp);
 		break;
 	case CAMSS_845:
-		r = &lane_regs_sdm845[0][0];
-		array_size = ARRAY_SIZE(lane_regs_sdm845[0]);
+		r = &lane_regs_sdm845[0];
+		array_size = ARRAY_SIZE(lane_regs_sdm845);
 		break;
 	default:
 		WARN(1, "unknown cspi version\n");
 		return;
 	}
 
-	for (l = 0; l < 5; l++) {
-		for (i = 0; i < array_size; i++, r++) {
-			switch (r->csiphy_param_type) {
-			case CSIPHY_SETTLE_CNT_LOWER_BYTE:
-				val = settle_cnt & 0xff;
-				break;
-			case CSIPHY_DNP_PARAMS:
-				continue;
-			default:
-				val = r->reg_data;
-				break;
-			}
-			writel_relaxed(val, csiphy->base + r->reg_addr);
+	for (i = 0; i < array_size; i++, r++) {
+		switch (r->csiphy_param_type) {
+		case CSIPHY_SETTLE_CNT_LOWER_BYTE:
+			val = settle_cnt & 0xff;
+			break;
+		case CSIPHY_DNP_PARAMS:
+			continue;
+		default:
+			val = r->reg_data;
+			break;
 		}
+		writel_relaxed(val, csiphy->base + r->reg_addr);
 	}
 }
 
-- 
2.34.1

[PATCH v8 03/16] media: qcom: camss: csiphy-3ph: Rename struct

[Depeng Shao]

From: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

The existing structure captures the configuration of CSIPHY lane registers.
Rename to struct csiphy_lane_regs to reflect.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Depeng Shao <quic_depengs@quicinc.com>
Reviewed-by: Elliot Berman <quic_eberman@quicinc.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
---
 .../media/platform/qcom/camss/camss-csiphy-3ph-1-0.c   | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c b/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c
index f7b851242aa5..73e4c05a9dec 100644
--- a/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c
+++ b/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c
@@ -56,7 +56,7 @@
 #define CSIPHY_2PH_REGS			5
 #define CSIPHY_3PH_REGS			6
 
-struct csiphy_reg_t {
+struct csiphy_lane_regs {
 	s32 reg_addr;
 	s32 reg_data;
 	s32 delay;
@@ -65,7 +65,7 @@ struct csiphy_reg_t {
 
 /* GEN2 1.0 2PH */
 static const struct
-csiphy_reg_t lane_regs_sdm845[] = {
+csiphy_lane_regs lane_regs_sdm845[] = {
 	{0x0004, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
 	{0x002C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
 	{0x0034, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
@@ -140,7 +140,7 @@ csiphy_reg_t lane_regs_sdm845[] = {
 
 /* GEN2 1.1 2PH */
 static const struct
-csiphy_reg_t lane_regs_sc8280xp[] = {
+csiphy_lane_regs lane_regs_sc8280xp[] = {
 	{0x0004, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
 	{0x002C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
 	{0x0034, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
@@ -215,7 +215,7 @@ csiphy_reg_t lane_regs_sc8280xp[] = {
 
 /* GEN2 1.2.1 2PH */
 static const struct
-csiphy_reg_t lane_regs_sm8250[] = {
+csiphy_lane_regs lane_regs_sm8250[] = {
 	{0x0030, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
 	{0x0900, 0x05, 0x00, CSIPHY_DEFAULT_PARAMS},
 	{0x0908, 0x10, 0x00, CSIPHY_DEFAULT_PARAMS},
@@ -470,7 +470,7 @@ static void csiphy_gen1_config_lanes(struct csiphy_device *csiphy,
 static void csiphy_gen2_config_lanes(struct csiphy_device *csiphy,
 				     u8 settle_cnt)
 {
-	const struct csiphy_reg_t *r;
+	const struct csiphy_lane_regs *r;
 	int i, array_size;
 	u32 val;
 
-- 
2.34.1

[PATCH v8 04/16] media: qcom: camss: csiphy: Add an init callback to CSI PHY devices

[Depeng Shao]

From: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

Add a nop init callback to CSIPHY devices, this callback is used to add
some HW register offset and register configuration for specific platform,
then different platform can reuse the same CSIPHY driver. Later changes
will enumerate with enabling code.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Depeng Shao <quic_depengs@quicinc.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
---
 drivers/media/platform/qcom/camss/camss-csiphy-2ph-1-0.c | 6 ++++++
 drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c | 6 ++++++
 drivers/media/platform/qcom/camss/camss-csiphy.c         | 4 ++++
 drivers/media/platform/qcom/camss/camss-csiphy.h         | 1 +
 4 files changed, 17 insertions(+)

diff --git a/drivers/media/platform/qcom/camss/camss-csiphy-2ph-1-0.c b/drivers/media/platform/qcom/camss/camss-csiphy-2ph-1-0.c
index cd4a8c369234..9d67e7fa6366 100644
--- a/drivers/media/platform/qcom/camss/camss-csiphy-2ph-1-0.c
+++ b/drivers/media/platform/qcom/camss/camss-csiphy-2ph-1-0.c
@@ -180,6 +180,11 @@ static irqreturn_t csiphy_isr(int irq, void *dev)
 	return IRQ_HANDLED;
 }
 
+static int csiphy_init(struct csiphy_device *csiphy)
+{
+	return 0;
+}
+
 const struct csiphy_hw_ops csiphy_ops_2ph_1_0 = {
 	.get_lane_mask = csiphy_get_lane_mask,
 	.hw_version_read = csiphy_hw_version_read,
@@ -187,4 +192,5 @@ const struct csiphy_hw_ops csiphy_ops_2ph_1_0 = {
 	.lanes_enable = csiphy_lanes_enable,
 	.lanes_disable = csiphy_lanes_disable,
 	.isr = csiphy_isr,
+	.init = csiphy_init,
 };
diff --git a/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c b/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c
index 73e4c05a9dec..b283df7634bb 100644
--- a/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c
+++ b/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c
@@ -586,6 +586,11 @@ static void csiphy_lanes_disable(struct csiphy_device *csiphy,
 			  CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(6));
 }
 
+static int csiphy_init(struct csiphy_device *csiphy)
+{
+	return 0;
+}
+
 const struct csiphy_hw_ops csiphy_ops_3ph_1_0 = {
 	.get_lane_mask = csiphy_get_lane_mask,
 	.hw_version_read = csiphy_hw_version_read,
@@ -593,4 +598,5 @@ const struct csiphy_hw_ops csiphy_ops_3ph_1_0 = {
 	.lanes_enable = csiphy_lanes_enable,
 	.lanes_disable = csiphy_lanes_disable,
 	.isr = csiphy_isr,
+	.init = csiphy_init,
 };
diff --git a/drivers/media/platform/qcom/camss/camss-csiphy.c b/drivers/media/platform/qcom/camss/camss-csiphy.c
index 3791c2d8a6cf..c053616558a7 100644
--- a/drivers/media/platform/qcom/camss/camss-csiphy.c
+++ b/drivers/media/platform/qcom/camss/camss-csiphy.c
@@ -594,6 +594,10 @@ int msm_csiphy_subdev_init(struct camss *camss,
 	csiphy->cfg.combo_mode = 0;
 	csiphy->res = &res->csiphy;
 
+	ret = csiphy->res->hw_ops->init(csiphy);
+	if (ret)
+		return ret;
+
 	/* Memory */
 
 	csiphy->base = devm_platform_ioremap_resource_byname(pdev, res->reg[0]);
diff --git a/drivers/media/platform/qcom/camss/camss-csiphy.h b/drivers/media/platform/qcom/camss/camss-csiphy.h
index 90cc3f976643..49393dfd5215 100644
--- a/drivers/media/platform/qcom/camss/camss-csiphy.h
+++ b/drivers/media/platform/qcom/camss/camss-csiphy.h
@@ -77,6 +77,7 @@ struct csiphy_hw_ops {
 	void (*lanes_disable)(struct csiphy_device *csiphy,
 			      struct csiphy_config *cfg);
 	irqreturn_t (*isr)(int irq, void *dev);
+	int (*init)(struct csiphy_device *csiphy);
 };
 
 struct csiphy_subdev_resources {
-- 
2.34.1

[PATCH v8 05/16] media: qcom: camss: csiphy-3ph: Move CSIPHY variables to data field inside csiphy struct

[Depeng Shao]

From: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

A .data field in the csiphy device structure allows us to extend out the
register layout of the three phase capable CSIPHY layer.

Move the existing lane configuration structure to an encapsulating
structure -> struct csiphy_device_regs which is derived from the .data
field populated at PHY init time, as opposed to calculated at lane
configuration.

Reviewed-by: default avatarVladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Depeng Shao <quic_depengs@quicinc.com>
---
 .../qcom/camss/camss-csiphy-3ph-1-0.c         | 54 ++++++++++---------
 .../media/platform/qcom/camss/camss-csiphy.h  |  6 +++
 2 files changed, 36 insertions(+), 24 deletions(-)

diff --git a/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c b/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c
index b283df7634bb..39cc7109ccf0 100644
--- a/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c
+++ b/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c
@@ -470,32 +470,10 @@ static void csiphy_gen1_config_lanes(struct csiphy_device *csiphy,
 static void csiphy_gen2_config_lanes(struct csiphy_device *csiphy,
 				     u8 settle_cnt)
 {
-	const struct csiphy_lane_regs *r;
-	int i, array_size;
+	const struct csiphy_lane_regs *r = csiphy->regs->lane_regs;
+	int i, array_size = csiphy->regs->lane_array_size;
 	u32 val;
 
-	switch (csiphy->camss->res->version) {
-	case CAMSS_7280:
-		r = &lane_regs_sm8250[0];
-		array_size = ARRAY_SIZE(lane_regs_sm8250);
-		break;
-	case CAMSS_8250:
-		r = &lane_regs_sm8250[0];
-		array_size = ARRAY_SIZE(lane_regs_sm8250);
-		break;
-	case CAMSS_8280XP:
-		r = &lane_regs_sc8280xp[0];
-		array_size = ARRAY_SIZE(lane_regs_sc8280xp);
-		break;
-	case CAMSS_845:
-		r = &lane_regs_sdm845[0];
-		array_size = ARRAY_SIZE(lane_regs_sdm845);
-		break;
-	default:
-		WARN(1, "unknown cspi version\n");
-		return;
-	}
-
 	for (i = 0; i < array_size; i++, r++) {
 		switch (r->csiphy_param_type) {
 		case CSIPHY_SETTLE_CNT_LOWER_BYTE:
@@ -588,6 +566,34 @@ static void csiphy_lanes_disable(struct csiphy_device *csiphy,
 
 static int csiphy_init(struct csiphy_device *csiphy)
 {
+	struct device *dev = csiphy->camss->dev;
+	struct csiphy_device_regs *regs;
+
+	regs = devm_kmalloc(dev, sizeof(*regs), GFP_KERNEL);
+	if (!regs)
+		return -ENOMEM;
+
+	csiphy->regs = regs;
+
+	switch (csiphy->camss->res->version) {
+	case CAMSS_845:
+		regs->lane_regs = &lane_regs_sdm845[0];
+		regs->lane_array_size = ARRAY_SIZE(lane_regs_sdm845);
+		break;
+	case CAMSS_7280:
+	case CAMSS_8250:
+		regs->lane_regs = &lane_regs_sm8250[0];
+		regs->lane_array_size = ARRAY_SIZE(lane_regs_sm8250);
+		break;
+	case CAMSS_8280XP:
+		regs->lane_regs = &lane_regs_sc8280xp[0];
+		regs->lane_array_size = ARRAY_SIZE(lane_regs_sc8280xp);
+		break;
+	default:
+		WARN(1, "unknown csiphy version\n");
+		return -ENODEV;
+	}
+
 	return 0;
 }
 
diff --git a/drivers/media/platform/qcom/camss/camss-csiphy.h b/drivers/media/platform/qcom/camss/camss-csiphy.h
index 49393dfd5215..4d731597fed7 100644
--- a/drivers/media/platform/qcom/camss/camss-csiphy.h
+++ b/drivers/media/platform/qcom/camss/camss-csiphy.h
@@ -85,6 +85,11 @@ struct csiphy_subdev_resources {
 	const struct csiphy_formats *formats;
 };
 
+struct csiphy_device_regs {
+	const struct csiphy_lane_regs *lane_regs;
+	int lane_array_size;
+};
+
 struct csiphy_device {
 	struct camss *camss;
 	u8 id;
@@ -103,6 +108,7 @@ struct csiphy_device {
 	struct csiphy_config cfg;
 	struct v4l2_mbus_framefmt fmt[MSM_CSIPHY_PADS_NUM];
 	const struct csiphy_subdev_resources *res;
+	struct csiphy_device_regs *regs;
 };
 
 struct camss_subdev_resources;
-- 
2.34.1

[PATCH v8 06/16] media: qcom: camss: csiphy-3ph: Use an offset variable to find common control regs

[Depeng Shao]

From: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

New versions of the CSIPHY locate the control registers at offset 0x1000
not offset 0x800.

Provide a variable to base an offset from for the purposes of redirecting
the base offset for the new PHY regs layout.

The existing setup bases from 0x800, the new from 0x1000 with some of the
'EXT' registers dropped but the lower-order lane config regs at offset 0x00
and up the same as before.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Depeng Shao <quic_depengs@quicinc.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
---
 .../qcom/camss/camss-csiphy-3ph-1-0.c         | 67 ++++++++++++-------
 .../media/platform/qcom/camss/camss-csiphy.h  |  1 +
 2 files changed, 44 insertions(+), 24 deletions(-)

diff --git a/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c b/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c
index 39cc7109ccf0..b5a116ced6a7 100644
--- a/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c
+++ b/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c
@@ -42,11 +42,11 @@
 #define CSIPHY_3PH_LNn_CSI_LANE_CTRL15(n)	(0x03c + 0x100 * (n))
 #define CSIPHY_3PH_LNn_CSI_LANE_CTRL15_SWI_SOT_SYMBOL	0xb8
 
-#define CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(n)	(0x800 + 0x4 * (n))
+#define CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(offset, n)	((offset) + 0x4 * (n))
 #define CSIPHY_3PH_CMN_CSI_COMMON_CTRL5_CLK_ENABLE	BIT(7)
 #define CSIPHY_3PH_CMN_CSI_COMMON_CTRL6_COMMON_PWRDN_B	BIT(0)
 #define CSIPHY_3PH_CMN_CSI_COMMON_CTRL6_SHOW_REV_ID	BIT(1)
-#define CSIPHY_3PH_CMN_CSI_COMMON_STATUSn(n)	(0x8b0 + 0x4 * (n))
+#define CSIPHY_3PH_CMN_CSI_COMMON_STATUSn(offset, n)	((offset) + 0xb0 + 0x4 * (n))
 
 #define CSIPHY_DEFAULT_PARAMS		0
 #define CSIPHY_LANE_ENABLE		1
@@ -321,19 +321,20 @@ csiphy_lane_regs lane_regs_sm8250[] = {
 static void csiphy_hw_version_read(struct csiphy_device *csiphy,
 				   struct device *dev)
 {
+	struct csiphy_device_regs *regs = csiphy->regs;
 	u32 hw_version;
 
-	writel(CSIPHY_3PH_CMN_CSI_COMMON_CTRL6_SHOW_REV_ID,
-	       csiphy->base + CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(6));
+	writel(CSIPHY_3PH_CMN_CSI_COMMON_CTRL6_SHOW_REV_ID, csiphy->base +
+	       CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(regs->offset, 6));
 
 	hw_version = readl_relaxed(csiphy->base +
-				   CSIPHY_3PH_CMN_CSI_COMMON_STATUSn(12));
+				   CSIPHY_3PH_CMN_CSI_COMMON_STATUSn(regs->offset, 12));
 	hw_version |= readl_relaxed(csiphy->base +
-				   CSIPHY_3PH_CMN_CSI_COMMON_STATUSn(13)) << 8;
+				   CSIPHY_3PH_CMN_CSI_COMMON_STATUSn(regs->offset, 13)) << 8;
 	hw_version |= readl_relaxed(csiphy->base +
-				   CSIPHY_3PH_CMN_CSI_COMMON_STATUSn(14)) << 16;
+				   CSIPHY_3PH_CMN_CSI_COMMON_STATUSn(regs->offset, 14)) << 16;
 	hw_version |= readl_relaxed(csiphy->base +
-				   CSIPHY_3PH_CMN_CSI_COMMON_STATUSn(15)) << 24;
+				   CSIPHY_3PH_CMN_CSI_COMMON_STATUSn(regs->offset, 15)) << 24;
 
 	dev_dbg(dev, "CSIPHY 3PH HW Version = 0x%08x\n", hw_version);
 }
@@ -344,31 +345,39 @@ static void csiphy_hw_version_read(struct csiphy_device *csiphy,
  */
 static void csiphy_reset(struct csiphy_device *csiphy)
 {
-	writel_relaxed(0x1, csiphy->base + CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(0));
+	struct csiphy_device_regs *regs = csiphy->regs;
+
+	writel_relaxed(0x1, csiphy->base +
+		      CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(regs->offset, 0));
 	usleep_range(5000, 8000);
-	writel_relaxed(0x0, csiphy->base + CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(0));
+	writel_relaxed(0x0, csiphy->base +
+		       CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(regs->offset, 0));
 }
 
 static irqreturn_t csiphy_isr(int irq, void *dev)
 {
 	struct csiphy_device *csiphy = dev;
+	struct csiphy_device_regs *regs = csiphy->regs;
 	int i;
 
 	for (i = 0; i < 11; i++) {
 		int c = i + 22;
 		u8 val = readl_relaxed(csiphy->base +
-				       CSIPHY_3PH_CMN_CSI_COMMON_STATUSn(i));
+				       CSIPHY_3PH_CMN_CSI_COMMON_STATUSn(regs->offset, i));
 
 		writel_relaxed(val, csiphy->base +
-				    CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(c));
+			       CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(regs->offset, c));
 	}
 
-	writel_relaxed(0x1, csiphy->base + CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(10));
-	writel_relaxed(0x0, csiphy->base + CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(10));
+	writel_relaxed(0x1, csiphy->base +
+		       CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(regs->offset, 10));
+	writel_relaxed(0x0, csiphy->base +
+		       CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(regs->offset, 10));
 
-	for (i = 22; i < 33; i++)
+	for (i = 22; i < 33; i++) {
 		writel_relaxed(0x0, csiphy->base +
-				    CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(i));
+			       CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(regs->offset, i));
+	}
 
 	return IRQ_HANDLED;
 }
@@ -523,6 +532,7 @@ static void csiphy_lanes_enable(struct csiphy_device *csiphy,
 				s64 link_freq, u8 lane_mask)
 {
 	struct csiphy_lanes_cfg *c = &cfg->csi2->lane_cfg;
+	struct csiphy_device_regs *regs = csiphy->regs;
 	u8 settle_cnt;
 	u8 val;
 	int i;
@@ -533,16 +543,20 @@ static void csiphy_lanes_enable(struct csiphy_device *csiphy,
 	for (i = 0; i < c->num_data; i++)
 		val |= BIT(c->data[i].pos * 2);
 
-	writel_relaxed(val, csiphy->base + CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(5));
+	writel_relaxed(val, csiphy->base +
+		       CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(regs->offset, 5));
 
 	val = CSIPHY_3PH_CMN_CSI_COMMON_CTRL6_COMMON_PWRDN_B;
-	writel_relaxed(val, csiphy->base + CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(6));
+	writel_relaxed(val, csiphy->base +
+		       CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(regs->offset, 6));
 
 	val = 0x02;
-	writel_relaxed(val, csiphy->base + CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(7));
+	writel_relaxed(val, csiphy->base +
+		       CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(regs->offset, 7));
 
 	val = 0x00;
-	writel_relaxed(val, csiphy->base + CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(0));
+	writel_relaxed(val, csiphy->base +
+		       CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(regs->offset, 0));
 
 	if (csiphy_is_gen2(csiphy->camss->res->version))
 		csiphy_gen2_config_lanes(csiphy, settle_cnt);
@@ -550,18 +564,22 @@ static void csiphy_lanes_enable(struct csiphy_device *csiphy,
 		csiphy_gen1_config_lanes(csiphy, cfg, settle_cnt);
 
 	/* IRQ_MASK registers - disable all interrupts */
-	for (i = 11; i < 22; i++)
-		writel_relaxed(0, csiphy->base + CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(i));
+	for (i = 11; i < 22; i++) {
+		writel_relaxed(0, csiphy->base +
+			       CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(regs->offset, i));
+	}
 }
 
 static void csiphy_lanes_disable(struct csiphy_device *csiphy,
 				 struct csiphy_config *cfg)
 {
+	struct csiphy_device_regs *regs = csiphy->regs;
+
 	writel_relaxed(0, csiphy->base +
-			  CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(5));
+			  CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(regs->offset, 5));
 
 	writel_relaxed(0, csiphy->base +
-			  CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(6));
+			  CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(regs->offset, 6));
 }
 
 static int csiphy_init(struct csiphy_device *csiphy)
@@ -574,6 +592,7 @@ static int csiphy_init(struct csiphy_device *csiphy)
 		return -ENOMEM;
 
 	csiphy->regs = regs;
+	regs->offset = 0x800;
 
 	switch (csiphy->camss->res->version) {
 	case CAMSS_845:
diff --git a/drivers/media/platform/qcom/camss/camss-csiphy.h b/drivers/media/platform/qcom/camss/camss-csiphy.h
index 4d731597fed7..86b98b37838e 100644
--- a/drivers/media/platform/qcom/camss/camss-csiphy.h
+++ b/drivers/media/platform/qcom/camss/camss-csiphy.h
@@ -88,6 +88,7 @@ struct csiphy_subdev_resources {
 struct csiphy_device_regs {
 	const struct csiphy_lane_regs *lane_regs;
 	int lane_array_size;
+	u32 offset;
 };
 
 struct csiphy_device {
-- 
2.34.1

[PATCH v8 07/16] media: qcom: camss: csid: Move common code into csid core

[Depeng Shao]

The get hw version and src pad code functions can be common code in csid
core file, then the csid driver of different hw version can reuse them,
rather than adding duplicate code in csid driver for each version.

Suggested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Depeng Shao <quic_depengs@quicinc.com>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
---
 .../platform/qcom/camss/camss-csid-4-1.c      | 19 -----
 .../platform/qcom/camss/camss-csid-4-7.c      | 42 ----------
 .../platform/qcom/camss/camss-csid-gen2.c     | 60 ---------------
 .../media/platform/qcom/camss/camss-csid.c    | 77 +++++++++++++++++++
 .../media/platform/qcom/camss/camss-csid.h    | 21 +++++
 5 files changed, 98 insertions(+), 121 deletions(-)

diff --git a/drivers/media/platform/qcom/camss/camss-csid-4-1.c b/drivers/media/platform/qcom/camss/camss-csid-4-1.c
index c95861420502..6998e1c52895 100644
--- a/drivers/media/platform/qcom/camss/camss-csid-4-1.c
+++ b/drivers/media/platform/qcom/camss/camss-csid-4-1.c
@@ -17,7 +17,6 @@
 #include "camss-csid-gen1.h"
 #include "camss.h"
 
-#define CAMSS_CSID_HW_VERSION		0x0
 #define CAMSS_CSID_CORE_CTRL_0		0x004
 #define CAMSS_CSID_CORE_CTRL_1		0x008
 #define CAMSS_CSID_RST_CMD		0x00c
@@ -139,15 +138,6 @@ static int csid_configure_testgen_pattern(struct csid_device *csid, s32 val)
 	return 0;
 }
 
-static u32 csid_hw_version(struct csid_device *csid)
-{
-	u32 hw_version = readl_relaxed(csid->base + CAMSS_CSID_HW_VERSION);
-
-	dev_dbg(csid->camss->dev, "CSID HW Version = 0x%08x\n", hw_version);
-
-	return hw_version;
-}
-
 static irqreturn_t csid_isr(int irq, void *dev)
 {
 	struct csid_device *csid = dev;
@@ -180,15 +170,6 @@ static int csid_reset(struct csid_device *csid)
 	return 0;
 }
 
-static u32 csid_src_pad_code(struct csid_device *csid, u32 sink_code,
-			     unsigned int match_format_idx, u32 match_code)
-{
-	if (match_format_idx > 0)
-		return 0;
-
-	return sink_code;
-}
-
 static void csid_subdev_init(struct csid_device *csid)
 {
 	csid->testgen.modes = csid_testgen_modes;
diff --git a/drivers/media/platform/qcom/camss/camss-csid-4-7.c b/drivers/media/platform/qcom/camss/camss-csid-4-7.c
index 08578a143688..66054d4872e6 100644
--- a/drivers/media/platform/qcom/camss/camss-csid-4-7.c
+++ b/drivers/media/platform/qcom/camss/camss-csid-4-7.c
@@ -16,7 +16,6 @@
 #include "camss-csid-gen1.h"
 #include "camss.h"
 
-#define CAMSS_CSID_HW_VERSION		0x0
 #define CAMSS_CSID_CORE_CTRL_0		0x004
 #define CAMSS_CSID_CORE_CTRL_1		0x008
 #define CAMSS_CSID_RST_CMD		0x010
@@ -151,15 +150,6 @@ static int csid_configure_testgen_pattern(struct csid_device *csid, s32 val)
 	return 0;
 }
 
-static u32 csid_hw_version(struct csid_device *csid)
-{
-	u32 hw_version = readl_relaxed(csid->base + CAMSS_CSID_HW_VERSION);
-
-	dev_dbg(csid->camss->dev, "CSID HW Version = 0x%08x\n", hw_version);
-
-	return hw_version;
-}
-
 /*
  * isr - CSID module interrupt service routine
  * @irq: Interrupt line
@@ -205,38 +195,6 @@ static int csid_reset(struct csid_device *csid)
 	return 0;
 }
 
-static u32 csid_src_pad_code(struct csid_device *csid, u32 sink_code,
-			     unsigned int match_format_idx, u32 match_code)
-{
-	switch (sink_code) {
-	case MEDIA_BUS_FMT_SBGGR10_1X10:
-	{
-		u32 src_code[] = {
-			MEDIA_BUS_FMT_SBGGR10_1X10,
-			MEDIA_BUS_FMT_SBGGR10_2X8_PADHI_LE,
-		};
-
-		return csid_find_code(src_code, ARRAY_SIZE(src_code),
-				      match_format_idx, match_code);
-	}
-	case MEDIA_BUS_FMT_Y10_1X10:
-	{
-		u32 src_code[] = {
-			MEDIA_BUS_FMT_Y10_1X10,
-			MEDIA_BUS_FMT_Y10_2X8_PADHI_LE,
-		};
-
-		return csid_find_code(src_code, ARRAY_SIZE(src_code),
-				      match_format_idx, match_code);
-	}
-	default:
-		if (match_format_idx > 0)
-			return 0;
-
-		return sink_code;
-	}
-}
-
 static void csid_subdev_init(struct csid_device *csid)
 {
 	csid->testgen.modes = csid_testgen_modes;
diff --git a/drivers/media/platform/qcom/camss/camss-csid-gen2.c b/drivers/media/platform/qcom/camss/camss-csid-gen2.c
index e1c757933e27..2a1746dcc1c5 100644
--- a/drivers/media/platform/qcom/camss/camss-csid-gen2.c
+++ b/drivers/media/platform/qcom/camss/camss-csid-gen2.c
@@ -22,11 +22,6 @@
  * alternate register layout.
  */
 
-#define CSID_HW_VERSION		0x0
-#define		HW_VERSION_STEPPING	0
-#define		HW_VERSION_REVISION	16
-#define		HW_VERSION_GENERATION	28
-
 #define CSID_RST_STROBES	0x10
 #define		RST_STROBES	0
 
@@ -351,29 +346,6 @@ static int csid_configure_testgen_pattern(struct csid_device *csid, s32 val)
 	return 0;
 }
 
-/*
- * csid_hw_version - CSID hardware version query
- * @csid: CSID device
- *
- * Return HW version or error
- */
-static u32 csid_hw_version(struct csid_device *csid)
-{
-	u32 hw_version;
-	u32 hw_gen;
-	u32 hw_rev;
-	u32 hw_step;
-
-	hw_version = readl_relaxed(csid->base + CSID_HW_VERSION);
-	hw_gen = (hw_version >> HW_VERSION_GENERATION) & 0xF;
-	hw_rev = (hw_version >> HW_VERSION_REVISION) & 0xFFF;
-	hw_step = (hw_version >> HW_VERSION_STEPPING) & 0xFFFF;
-	dev_dbg(csid->camss->dev, "CSID HW Version = %u.%u.%u\n",
-		hw_gen, hw_rev, hw_step);
-
-	return hw_version;
-}
-
 /*
  * csid_isr - CSID module interrupt service routine
  * @irq: Interrupt line
@@ -443,38 +415,6 @@ static int csid_reset(struct csid_device *csid)
 	return 0;
 }
 
-static u32 csid_src_pad_code(struct csid_device *csid, u32 sink_code,
-			     unsigned int match_format_idx, u32 match_code)
-{
-	switch (sink_code) {
-	case MEDIA_BUS_FMT_SBGGR10_1X10:
-	{
-		u32 src_code[] = {
-			MEDIA_BUS_FMT_SBGGR10_1X10,
-			MEDIA_BUS_FMT_SBGGR10_2X8_PADHI_LE,
-		};
-
-		return csid_find_code(src_code, ARRAY_SIZE(src_code),
-				      match_format_idx, match_code);
-	}
-	case MEDIA_BUS_FMT_Y10_1X10:
-	{
-		u32 src_code[] = {
-			MEDIA_BUS_FMT_Y10_1X10,
-			MEDIA_BUS_FMT_Y10_2X8_PADHI_LE,
-		};
-
-		return csid_find_code(src_code, ARRAY_SIZE(src_code),
-				      match_format_idx, match_code);
-	}
-	default:
-		if (match_format_idx > 0)
-			return 0;
-
-		return sink_code;
-	}
-}
-
 static void csid_subdev_init(struct csid_device *csid)
 {
 	csid->testgen.modes = csid_testgen_modes;
diff --git a/drivers/media/platform/qcom/camss/camss-csid.c b/drivers/media/platform/qcom/camss/camss-csid.c
index 858db5d4ca75..6cf8e434dc05 100644
--- a/drivers/media/platform/qcom/camss/camss-csid.c
+++ b/drivers/media/platform/qcom/camss/camss-csid.c
@@ -29,6 +29,11 @@
 #define VFE_480_CSID_OFFSET 0x1200
 #define VFE_480_LITE_CSID_OFFSET 0x200
 
+#define CSID_HW_VERSION		0x0
+#define		HW_VERSION_STEPPING	0
+#define		HW_VERSION_REVISION	16
+#define		HW_VERSION_GENERATION	28
+
 #define MSM_CSID_NAME "msm_csid"
 
 const char * const csid_testgen_modes[] = {
@@ -590,6 +595,78 @@ static int csid_set_clock_rates(struct csid_device *csid)
 	return 0;
 }
 
+/*
+ * csid_hw_version - CSID hardware version query
+ * @csid: CSID device
+ *
+ * Return HW version or error
+ */
+u32 csid_hw_version(struct csid_device *csid)
+{
+	u32 hw_version;
+	u32 hw_gen;
+	u32 hw_rev;
+	u32 hw_step;
+
+	hw_version = readl_relaxed(csid->base + CSID_HW_VERSION);
+	hw_gen = (hw_version >> HW_VERSION_GENERATION) & 0xF;
+	hw_rev = (hw_version >> HW_VERSION_REVISION) & 0xFFF;
+	hw_step = (hw_version >> HW_VERSION_STEPPING) & 0xFFFF;
+	dev_info(csid->camss->dev, "CSID:%d HW Version = %u.%u.%u\n",
+		 csid->id, hw_gen, hw_rev, hw_step);
+
+	return hw_version;
+}
+
+/*
+ * csid_src_pad_code - Pick an output/src format based on the input/sink format
+ * @csid: CSID device
+ * @sink_code: The sink format of the input
+ * @match_format_idx: Request preferred index, as defined by subdevice csid
+ *                    format. Set @match_code to 0 if used.
+ * @match_code: Request preferred code, set @match_format_idx to 0 if used
+ *
+ * Return 0 on failure or src format code otherwise
+ */
+u32 csid_src_pad_code(struct csid_device *csid, u32 sink_code,
+		      unsigned int match_format_idx, u32 match_code)
+{
+	if (csid->camss->res->version == CAMSS_8x16) {
+		if (match_format_idx > 0)
+			return 0;
+
+		return sink_code;
+	}
+
+	switch (sink_code) {
+	case MEDIA_BUS_FMT_SBGGR10_1X10:
+	{
+		u32 src_code[] = {
+			MEDIA_BUS_FMT_SBGGR10_1X10,
+			MEDIA_BUS_FMT_SBGGR10_2X8_PADHI_LE,
+		};
+
+		return csid_find_code(src_code, ARRAY_SIZE(src_code),
+				      match_format_idx, match_code);
+	}
+	case MEDIA_BUS_FMT_Y10_1X10:
+	{
+		u32 src_code[] = {
+			MEDIA_BUS_FMT_Y10_1X10,
+			MEDIA_BUS_FMT_Y10_2X8_PADHI_LE,
+		};
+
+		return csid_find_code(src_code, ARRAY_SIZE(src_code),
+				      match_format_idx, match_code);
+	}
+	default:
+		if (match_format_idx > 0)
+			return 0;
+
+		return sink_code;
+	}
+}
+
 /*
  * csid_set_power - Power on/off CSID module
  * @sd: CSID V4L2 subdevice
diff --git a/drivers/media/platform/qcom/camss/camss-csid.h b/drivers/media/platform/qcom/camss/camss-csid.h
index 8cdae98e4dca..f52209b96583 100644
--- a/drivers/media/platform/qcom/camss/camss-csid.h
+++ b/drivers/media/platform/qcom/camss/camss-csid.h
@@ -237,4 +237,25 @@ extern const struct csid_hw_ops csid_ops_gen2;
  */
 bool csid_is_lite(struct csid_device *csid);
 
+/*
+ * csid_hw_version - CSID hardware version query
+ * @csid: CSID device
+ *
+ * Return HW version or error
+ */
+u32 csid_hw_version(struct csid_device *csid);
+
+/*
+ * csid_src_pad_code - Pick an output/src format based on the input/sink format
+ * @csid: CSID device
+ * @sink_code: The sink format of the input
+ * @match_format_idx: Request preferred index, as defined by subdevice csid
+ *                    format. Set @match_code to 0 if used.
+ * @match_code: Request preferred code, set @match_format_idx to 0 if used
+ *
+ * Return 0 on failure or src format code otherwise
+ */
+u32 csid_src_pad_code(struct csid_device *csid, u32 sink_code,
+		      unsigned int match_format_idx, u32 match_code);
+
 #endif /* QC_MSM_CAMSS_CSID_H */
-- 
2.34.1

[PATCH v8 08/16] media: qcom: camss: vfe: Move common code into vfe core

[Depeng Shao]

Some v4l2 buffer related logic functions can be moved to vfe core as
common code, then the vfe driver of different hw version can reuse them,
this also can avoid adding duplicate code for new version supporting.

Suggested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Depeng Shao <quic_depengs@quicinc.com>
---
 .../media/platform/qcom/camss/camss-vfe-17x.c | 112 +------
 .../media/platform/qcom/camss/camss-vfe-4-1.c |   9 -
 .../media/platform/qcom/camss/camss-vfe-4-7.c |  11 -
 .../media/platform/qcom/camss/camss-vfe-4-8.c |  11 -
 .../media/platform/qcom/camss/camss-vfe-480.c | 274 ++----------------
 drivers/media/platform/qcom/camss/camss-vfe.c | 268 +++++++++++++++++
 drivers/media/platform/qcom/camss/camss-vfe.h |  58 +++-
 7 files changed, 361 insertions(+), 382 deletions(-)

diff --git a/drivers/media/platform/qcom/camss/camss-vfe-17x.c b/drivers/media/platform/qcom/camss/camss-vfe-17x.c
index 380c99321030..e5ee7e717b3b 100644
--- a/drivers/media/platform/qcom/camss/camss-vfe-17x.c
+++ b/drivers/media/platform/qcom/camss/camss-vfe-17x.c
@@ -14,8 +14,6 @@
 #include "camss.h"
 #include "camss-vfe.h"
 
-#define VFE_HW_VERSION				(0x000)
-
 #define VFE_GLOBAL_RESET_CMD			(0x018)
 #define		GLOBAL_RESET_CMD_CORE		BIT(0)
 #define		GLOBAL_RESET_CMD_CAMIF		BIT(1)
@@ -176,20 +174,6 @@
 #define VFE_BUS_WM_FRAME_INC(n)			(0x2258 + (n) * 0x100)
 #define VFE_BUS_WM_BURST_LIMIT(n)		(0x225c + (n) * 0x100)
 
-static u32 vfe_hw_version(struct vfe_device *vfe)
-{
-	u32 hw_version = readl_relaxed(vfe->base + VFE_HW_VERSION);
-
-	u32 gen = (hw_version >> 28) & 0xF;
-	u32 rev = (hw_version >> 16) & 0xFFF;
-	u32 step = hw_version & 0xFFFF;
-
-	dev_dbg(vfe->camss->dev, "VFE HW Version = %u.%u.%u\n",
-		gen, rev, step);
-
-	return hw_version;
-}
-
 static inline void vfe_reg_set(struct vfe_device *vfe, u32 reg, u32 set_bits)
 {
 	u32 bits = readl_relaxed(vfe->base + reg);
@@ -438,62 +422,6 @@ static int vfe_get_output(struct vfe_line *line)
 	return -EINVAL;
 }
 
-static int vfe_enable_output(struct vfe_line *line)
-{
-	struct vfe_device *vfe = to_vfe(line);
-	struct vfe_output *output = &line->output;
-	const struct vfe_hw_ops *ops = vfe->res->hw_ops;
-	struct media_entity *sensor;
-	unsigned long flags;
-	unsigned int frame_skip = 0;
-	unsigned int i;
-
-	sensor = camss_find_sensor(&line->subdev.entity);
-	if (sensor) {
-		struct v4l2_subdev *subdev = media_entity_to_v4l2_subdev(sensor);
-
-		v4l2_subdev_call(subdev, sensor, g_skip_frames, &frame_skip);
-		/* Max frame skip is 29 frames */
-		if (frame_skip > VFE_FRAME_DROP_VAL - 1)
-			frame_skip = VFE_FRAME_DROP_VAL - 1;
-	}
-
-	spin_lock_irqsave(&vfe->output_lock, flags);
-
-	ops->reg_update_clear(vfe, line->id);
-
-	if (output->state > VFE_OUTPUT_RESERVED) {
-		dev_err(vfe->camss->dev, "Output is not in reserved state %d\n",
-			output->state);
-		spin_unlock_irqrestore(&vfe->output_lock, flags);
-		return -EINVAL;
-	}
-
-	WARN_ON(output->gen2.active_num);
-
-	output->state = VFE_OUTPUT_ON;
-
-	output->sequence = 0;
-	output->wait_reg_update = 0;
-	reinit_completion(&output->reg_update);
-
-	vfe_wm_start(vfe, output->wm_idx[0], line);
-
-	for (i = 0; i < 2; i++) {
-		output->buf[i] = vfe_buf_get_pending(output);
-		if (!output->buf[i])
-			break;
-		output->gen2.active_num++;
-		vfe_wm_update(vfe, output->wm_idx[0], output->buf[i]->addr[0], line);
-	}
-
-	ops->reg_update(vfe, line->id);
-
-	spin_unlock_irqrestore(&vfe->output_lock, flags);
-
-	return 0;
-}
-
 /*
  * vfe_enable - Enable streaming on VFE line
  * @line: VFE line
@@ -518,7 +446,7 @@ static int vfe_enable(struct vfe_line *line)
 	if (ret < 0)
 		goto error_get_output;
 
-	ret = vfe_enable_output(line);
+	ret = vfe_enable_output_v2(line);
 	if (ret < 0)
 		goto error_enable_output;
 
@@ -627,40 +555,6 @@ static void vfe_isr_wm_done(struct vfe_device *vfe, u8 wm)
 	spin_unlock_irqrestore(&vfe->output_lock, flags);
 }
 
-/*
- * vfe_queue_buffer - Add empty buffer
- * @vid: Video device structure
- * @buf: Buffer to be enqueued
- *
- * Add an empty buffer - depending on the current number of buffers it will be
- * put in pending buffer queue or directly given to the hardware to be filled.
- *
- * Return 0 on success or a negative error code otherwise
- */
-static int vfe_queue_buffer(struct camss_video *vid,
-			    struct camss_buffer *buf)
-{
-	struct vfe_line *line = container_of(vid, struct vfe_line, video_out);
-	struct vfe_device *vfe = to_vfe(line);
-	struct vfe_output *output;
-	unsigned long flags;
-
-	output = &line->output;
-
-	spin_lock_irqsave(&vfe->output_lock, flags);
-
-	if (output->state == VFE_OUTPUT_ON && output->gen2.active_num < 2) {
-		output->buf[output->gen2.active_num++] = buf;
-		vfe_wm_update(vfe, output->wm_idx[0], buf->addr[0], line);
-	} else {
-		vfe_buf_add_pending(output, buf);
-	}
-
-	spin_unlock_irqrestore(&vfe->output_lock, flags);
-
-	return 0;
-}
-
 static const struct vfe_isr_ops vfe_isr_ops_170 = {
 	.reset_ack = vfe_isr_reset_ack,
 	.halt_ack = vfe_isr_halt_ack,
@@ -671,7 +565,7 @@ static const struct vfe_isr_ops vfe_isr_ops_170 = {
 };
 
 static const struct camss_video_ops vfe_video_ops_170 = {
-	.queue_buffer = vfe_queue_buffer,
+	.queue_buffer = vfe_queue_buffer_v2,
 	.flush_buffers = vfe_flush_buffers,
 };
 
@@ -695,5 +589,7 @@ const struct vfe_hw_ops vfe_ops_170 = {
 	.vfe_enable = vfe_enable,
 	.vfe_halt = vfe_halt,
 	.violation_read = vfe_violation_read,
+	.vfe_wm_start = vfe_wm_start,
 	.vfe_wm_stop = vfe_wm_stop,
+	.vfe_wm_update = vfe_wm_update,
 };
diff --git a/drivers/media/platform/qcom/camss/camss-vfe-4-1.c b/drivers/media/platform/qcom/camss/camss-vfe-4-1.c
index 9a9007c3ff33..901677293d97 100644
--- a/drivers/media/platform/qcom/camss/camss-vfe-4-1.c
+++ b/drivers/media/platform/qcom/camss/camss-vfe-4-1.c
@@ -210,15 +210,6 @@
 #define MSM_VFE_VFE0_UB_SIZE 1023
 #define MSM_VFE_VFE0_UB_SIZE_RDI (MSM_VFE_VFE0_UB_SIZE / 3)
 
-static u32 vfe_hw_version(struct vfe_device *vfe)
-{
-	u32 hw_version = readl_relaxed(vfe->base + VFE_0_HW_VERSION);
-
-	dev_dbg(vfe->camss->dev, "VFE HW Version = 0x%08x\n", hw_version);
-
-	return hw_version;
-}
-
 static u16 vfe_get_ub_size(u8 vfe_id)
 {
 	if (vfe_id == 0)
diff --git a/drivers/media/platform/qcom/camss/camss-vfe-4-7.c b/drivers/media/platform/qcom/camss/camss-vfe-4-7.c
index ce0719106bd3..76729607db02 100644
--- a/drivers/media/platform/qcom/camss/camss-vfe-4-7.c
+++ b/drivers/media/platform/qcom/camss/camss-vfe-4-7.c
@@ -18,8 +18,6 @@
 #include "camss-vfe-gen1.h"
 
 
-#define VFE_0_HW_VERSION		0x000
-
 #define VFE_0_GLOBAL_RESET_CMD		0x018
 #define VFE_0_GLOBAL_RESET_CMD_CORE	BIT(0)
 #define VFE_0_GLOBAL_RESET_CMD_CAMIF	BIT(1)
@@ -254,15 +252,6 @@
 #define MSM_VFE_VFE1_UB_SIZE 1535
 #define MSM_VFE_VFE1_UB_SIZE_RDI (MSM_VFE_VFE1_UB_SIZE / 3)
 
-static u32 vfe_hw_version(struct vfe_device *vfe)
-{
-	u32 hw_version = readl_relaxed(vfe->base + VFE_0_HW_VERSION);
-
-	dev_dbg(vfe->camss->dev, "VFE HW Version = 0x%08x\n", hw_version);
-
-	return hw_version;
-}
-
 static u16 vfe_get_ub_size(u8 vfe_id)
 {
 	if (vfe_id == 0)
diff --git a/drivers/media/platform/qcom/camss/camss-vfe-4-8.c b/drivers/media/platform/qcom/camss/camss-vfe-4-8.c
index 6b59c8107a3c..b2f7d855d8dd 100644
--- a/drivers/media/platform/qcom/camss/camss-vfe-4-8.c
+++ b/drivers/media/platform/qcom/camss/camss-vfe-4-8.c
@@ -17,8 +17,6 @@
 #include "camss-vfe.h"
 #include "camss-vfe-gen1.h"
 
-#define VFE_0_HW_VERSION		0x000
-
 #define VFE_0_GLOBAL_RESET_CMD		0x018
 #define VFE_0_GLOBAL_RESET_CMD_CORE	BIT(0)
 #define VFE_0_GLOBAL_RESET_CMD_CAMIF	BIT(1)
@@ -247,15 +245,6 @@
 #define MSM_VFE_VFE1_UB_SIZE 1535
 #define MSM_VFE_VFE1_UB_SIZE_RDI (MSM_VFE_VFE1_UB_SIZE / 3)
 
-static u32 vfe_hw_version(struct vfe_device *vfe)
-{
-	u32 hw_version = readl_relaxed(vfe->base + VFE_0_HW_VERSION);
-
-	dev_dbg(vfe->camss->dev, "VFE HW Version = 0x%08x\n", hw_version);
-
-	return hw_version;
-}
-
 static inline void vfe_reg_clr(struct vfe_device *vfe, u32 reg, u32 clr_bits)
 {
 	u32 bits = readl_relaxed(vfe->base + reg);
diff --git a/drivers/media/platform/qcom/camss/camss-vfe-480.c b/drivers/media/platform/qcom/camss/camss-vfe-480.c
index dc2735476c82..4feea590a47b 100644
--- a/drivers/media/platform/qcom/camss/camss-vfe-480.c
+++ b/drivers/media/platform/qcom/camss/camss-vfe-480.c
@@ -15,8 +15,6 @@
 #include "camss.h"
 #include "camss-vfe.h"
 
-#define VFE_HW_VERSION			(0x00)
-
 #define VFE_GLOBAL_RESET_CMD		(vfe_is_lite(vfe) ? 0x0c : 0x1c)
 #define	    GLOBAL_RESET_HW_AND_REG	(vfe_is_lite(vfe) ? BIT(1) : BIT(0))
 
@@ -92,19 +90,6 @@ static inline int bus_irq_mask_0_comp_done(struct vfe_device *vfe, int n)
 
 #define MAX_VFE_OUTPUT_LINES	4
 
-static u32 vfe_hw_version(struct vfe_device *vfe)
-{
-	u32 hw_version = readl_relaxed(vfe->base + VFE_HW_VERSION);
-
-	u32 gen = (hw_version >> 28) & 0xF;
-	u32 rev = (hw_version >> 16) & 0xFFF;
-	u32 step = hw_version & 0xFFFF;
-
-	dev_dbg(vfe->camss->dev, "VFE HW Version = %u.%u.%u\n", gen, rev, step);
-
-	return hw_version;
-}
-
 static void vfe_global_reset(struct vfe_device *vfe)
 {
 	writel_relaxed(IRQ_MASK_0_RESET_ACK, vfe->base + VFE_IRQ_MASK(0));
@@ -167,18 +152,16 @@ static inline void vfe_reg_update_clear(struct vfe_device *vfe,
 	vfe->reg_update &= ~REG_UPDATE_RDI(vfe, line_id);
 }
 
-static void vfe_enable_irq_common(struct vfe_device *vfe)
-{
-	/* enable reset ack IRQ and top BUS status IRQ */
-	writel_relaxed(IRQ_MASK_0_RESET_ACK | IRQ_MASK_0_BUS_TOP_IRQ,
-		       vfe->base + VFE_IRQ_MASK(0));
-}
-
-static void vfe_enable_lines_irq(struct vfe_device *vfe)
+static void vfe_enable_irq(struct vfe_device *vfe)
 {
 	int i;
 	u32 bus_irq_mask = 0;
 
+	if (!vfe->stream_count)
+		/* enable reset ack IRQ and top BUS status IRQ */
+		writel(IRQ_MASK_0_RESET_ACK | IRQ_MASK_0_BUS_TOP_IRQ,
+		       vfe->base + VFE_IRQ_MASK(0));
+
 	for (i = 0; i < MAX_VFE_OUTPUT_LINES; i++) {
 		/* Enable IRQ for newly added lines, but also keep already running lines's IRQ */
 		if (vfe->line[i].output.state == VFE_OUTPUT_RESERVED ||
@@ -188,11 +171,10 @@ static void vfe_enable_lines_irq(struct vfe_device *vfe)
 			}
 	}
 
-	writel_relaxed(bus_irq_mask, vfe->base + VFE_BUS_IRQ_MASK(0));
+	writel(bus_irq_mask, vfe->base + VFE_BUS_IRQ_MASK(0));
 }
 
 static void vfe_isr_reg_update(struct vfe_device *vfe, enum vfe_line_id line_id);
-static void vfe_isr_wm_done(struct vfe_device *vfe, u8 wm);
 
 /*
  * vfe_isr - VFE module interrupt handler
@@ -226,7 +208,7 @@ static irqreturn_t vfe_isr(int irq, void *dev)
 				vfe_isr_reg_update(vfe, i);
 
 			if (status & BUS_IRQ_MASK_0_COMP_DONE(vfe, RDI_COMP_GROUP(i)))
-				vfe_isr_wm_done(vfe, i);
+				vfe_buf_done(vfe, i);
 		}
 	}
 
@@ -245,132 +227,6 @@ static int vfe_halt(struct vfe_device *vfe)
 	return 0;
 }
 
-static int vfe_get_output(struct vfe_line *line)
-{
-	struct vfe_device *vfe = to_vfe(line);
-	struct vfe_output *output;
-	unsigned long flags;
-
-	spin_lock_irqsave(&vfe->output_lock, flags);
-
-	output = &line->output;
-	if (output->state > VFE_OUTPUT_RESERVED) {
-		dev_err(vfe->camss->dev, "Output is running\n");
-		goto error;
-	}
-
-	output->wm_num = 1;
-
-	/* Correspondence between VFE line number and WM number.
-	 * line 0 -> RDI 0, line 1 -> RDI1, line 2 -> RDI2, line 3 -> PIX/RDI3
-	 * Note this 1:1 mapping will not work for PIX streams.
-	 */
-	output->wm_idx[0] = line->id;
-	vfe->wm_output_map[line->id] = line->id;
-
-	output->drop_update_idx = 0;
-
-	spin_unlock_irqrestore(&vfe->output_lock, flags);
-
-	return 0;
-
-error:
-	spin_unlock_irqrestore(&vfe->output_lock, flags);
-	output->state = VFE_OUTPUT_OFF;
-
-	return -EINVAL;
-}
-
-static int vfe_enable_output(struct vfe_line *line)
-{
-	struct vfe_device *vfe = to_vfe(line);
-	struct vfe_output *output = &line->output;
-	unsigned long flags;
-	unsigned int i;
-
-	spin_lock_irqsave(&vfe->output_lock, flags);
-
-	vfe_reg_update_clear(vfe, line->id);
-
-	if (output->state > VFE_OUTPUT_RESERVED) {
-		dev_err(vfe->camss->dev, "Output is not in reserved state %d\n",
-			output->state);
-		spin_unlock_irqrestore(&vfe->output_lock, flags);
-		return -EINVAL;
-	}
-
-	WARN_ON(output->gen2.active_num);
-
-	output->state = VFE_OUTPUT_ON;
-
-	output->sequence = 0;
-	output->wait_reg_update = 0;
-	reinit_completion(&output->reg_update);
-
-	vfe_wm_start(vfe, output->wm_idx[0], line);
-
-	for (i = 0; i < 2; i++) {
-		output->buf[i] = vfe_buf_get_pending(output);
-		if (!output->buf[i])
-			break;
-		output->gen2.active_num++;
-		vfe_wm_update(vfe, output->wm_idx[0], output->buf[i]->addr[0], line);
-	}
-
-	vfe_reg_update(vfe, line->id);
-
-	spin_unlock_irqrestore(&vfe->output_lock, flags);
-
-	return 0;
-}
-
-/*
- * vfe_enable - Enable streaming on VFE line
- * @line: VFE line
- *
- * Return 0 on success or a negative error code otherwise
- */
-static int vfe_enable(struct vfe_line *line)
-{
-	struct vfe_device *vfe = to_vfe(line);
-	int ret;
-
-	mutex_lock(&vfe->stream_lock);
-
-	if (!vfe->stream_count)
-		vfe_enable_irq_common(vfe);
-
-	vfe->stream_count++;
-
-	vfe_enable_lines_irq(vfe);
-
-	mutex_unlock(&vfe->stream_lock);
-
-	ret = vfe_get_output(line);
-	if (ret < 0)
-		goto error_get_output;
-
-	ret = vfe_enable_output(line);
-	if (ret < 0)
-		goto error_enable_output;
-
-	vfe->was_streaming = 1;
-
-	return 0;
-
-error_enable_output:
-	vfe_put_output(line);
-
-error_get_output:
-	mutex_lock(&vfe->stream_lock);
-
-	vfe->stream_count--;
-
-	mutex_unlock(&vfe->stream_lock);
-
-	return ret;
-}
-
 /*
  * vfe_isr_reg_update - Process reg update interrupt
  * @vfe: VFE Device
@@ -394,114 +250,48 @@ static void vfe_isr_reg_update(struct vfe_device *vfe, enum vfe_line_id line_id)
 	spin_unlock_irqrestore(&vfe->output_lock, flags);
 }
 
-/*
- * vfe_isr_wm_done - Process write master done interrupt
- * @vfe: VFE Device
- * @wm: Write master id
- */
-static void vfe_isr_wm_done(struct vfe_device *vfe, u8 wm)
-{
-	struct vfe_line *line = &vfe->line[vfe->wm_output_map[wm]];
-	struct camss_buffer *ready_buf;
-	struct vfe_output *output;
-	unsigned long flags;
-	u32 index;
-	u64 ts = ktime_get_ns();
-
-	spin_lock_irqsave(&vfe->output_lock, flags);
-
-	if (vfe->wm_output_map[wm] == VFE_LINE_NONE) {
-		dev_err_ratelimited(vfe->camss->dev,
-				    "Received wm done for unmapped index\n");
-		goto out_unlock;
-	}
-	output = &vfe->line[vfe->wm_output_map[wm]].output;
-
-	ready_buf = output->buf[0];
-	if (!ready_buf) {
-		dev_err_ratelimited(vfe->camss->dev,
-				    "Missing ready buf %d!\n", output->state);
-		goto out_unlock;
-	}
-
-	ready_buf->vb.vb2_buf.timestamp = ts;
-	ready_buf->vb.sequence = output->sequence++;
-
-	index = 0;
-	output->buf[0] = output->buf[1];
-	if (output->buf[0])
-		index = 1;
-
-	output->buf[index] = vfe_buf_get_pending(output);
-
-	if (output->buf[index])
-		vfe_wm_update(vfe, output->wm_idx[0], output->buf[index]->addr[0], line);
-	else
-		output->gen2.active_num--;
-
-	spin_unlock_irqrestore(&vfe->output_lock, flags);
-
-	vb2_buffer_done(&ready_buf->vb.vb2_buf, VB2_BUF_STATE_DONE);
-
-	return;
+static const struct camss_video_ops vfe_video_ops_480 = {
+	.queue_buffer = vfe_queue_buffer_v2,
+	.flush_buffers = vfe_flush_buffers,
+};
 
-out_unlock:
-	spin_unlock_irqrestore(&vfe->output_lock, flags);
+static void vfe_subdev_init(struct device *dev, struct vfe_device *vfe)
+{
+	vfe->video_ops = vfe_video_ops_480;
 }
 
-/*
- * vfe_queue_buffer - Add empty buffer
- * @vid: Video device structure
- * @buf: Buffer to be enqueued
- *
- * Add an empty buffer - depending on the current number of buffers it will be
- * put in pending buffer queue or directly given to the hardware to be filled.
- *
- * Return 0 on success or a negative error code otherwise
- */
-static int vfe_queue_buffer(struct camss_video *vid,
-			    struct camss_buffer *buf)
+static void vfe_isr_read(struct vfe_device *vfe, u32 *value0, u32 *value1)
 {
-	struct vfe_line *line = container_of(vid, struct vfe_line, video_out);
-	struct vfe_device *vfe = to_vfe(line);
-	struct vfe_output *output;
-	unsigned long flags;
-
-	output = &line->output;
-
-	spin_lock_irqsave(&vfe->output_lock, flags);
-
-	if (output->state == VFE_OUTPUT_ON && output->gen2.active_num < 2) {
-		output->buf[output->gen2.active_num++] = buf;
-		vfe_wm_update(vfe, output->wm_idx[0], buf->addr[0], line);
-	} else {
-		vfe_buf_add_pending(output, buf);
-	}
-
-	spin_unlock_irqrestore(&vfe->output_lock, flags);
-
-	return 0;
+	/* nop */
 }
 
-static const struct camss_video_ops vfe_video_ops_480 = {
-	.queue_buffer = vfe_queue_buffer,
-	.flush_buffers = vfe_flush_buffers,
-};
+static void vfe_violation_read(struct vfe_device *vfe)
+{
+	/* nop */
+}
 
-static void vfe_subdev_init(struct device *dev, struct vfe_device *vfe)
+static void vfe_buf_done_480(struct vfe_device *vfe, int port_id)
 {
-	vfe->video_ops = vfe_video_ops_480;
+	/* nop */
 }
 
 const struct vfe_hw_ops vfe_ops_480 = {
+	.enable_irq = vfe_enable_irq,
 	.global_reset = vfe_global_reset,
 	.hw_version = vfe_hw_version,
 	.isr = vfe_isr,
+	.isr_read = vfe_isr_read,
+	.reg_update = vfe_reg_update,
+	.reg_update_clear = vfe_reg_update_clear,
 	.pm_domain_off = vfe_pm_domain_off,
 	.pm_domain_on = vfe_pm_domain_on,
 	.subdev_init = vfe_subdev_init,
 	.vfe_disable = vfe_disable,
-	.vfe_enable = vfe_enable,
+	.vfe_enable = vfe_enable_v2,
 	.vfe_halt = vfe_halt,
+	.violation_read = vfe_violation_read,
+	.vfe_wm_start = vfe_wm_start,
 	.vfe_wm_stop = vfe_wm_stop,
+	.vfe_buf_done = vfe_buf_done_480,
+	.vfe_wm_update = vfe_wm_update,
 };
diff --git a/drivers/media/platform/qcom/camss/camss-vfe.c b/drivers/media/platform/qcom/camss/camss-vfe.c
index 95f6a1ac7eaf..818dba4b14dc 100644
--- a/drivers/media/platform/qcom/camss/camss-vfe.c
+++ b/drivers/media/platform/qcom/camss/camss-vfe.c
@@ -32,6 +32,11 @@
 
 #define SCALER_RATIO_MAX 16
 
+#define VFE_HW_VERSION		0x0
+#define		HW_VERSION_STEPPING	0
+#define		HW_VERSION_REVISION	16
+#define		HW_VERSION_GENERATION	28
+
 static const struct camss_format_info formats_rdi_8x16[] = {
 	{ MEDIA_BUS_FMT_UYVY8_1X16, 8, V4L2_PIX_FMT_UYVY, 1,
 	  PER_PLANE_DATA(0, 1, 1, 1, 1, 16) },
@@ -404,6 +409,269 @@ static u32 vfe_src_pad_code(struct vfe_line *line, u32 sink_code,
 	return 0;
 }
 
+/*
+ * vfe_hw_version - Process write master done interrupt
+ * @vfe: VFE Device
+ *
+ * Return vfe hw version
+ */
+u32 vfe_hw_version(struct vfe_device *vfe)
+{
+	u32 hw_version = readl_relaxed(vfe->base + VFE_HW_VERSION);
+
+	u32 gen = (hw_version >> HW_VERSION_GENERATION) & 0xF;
+	u32 rev = (hw_version >> HW_VERSION_REVISION) & 0xFFF;
+	u32 step = (hw_version >> HW_VERSION_STEPPING) & 0xFFFF;
+
+	dev_info(vfe->camss->dev, "VFE:%d HW Version = %u.%u.%u\n",
+		 vfe->id, gen, rev, step);
+
+	return hw_version;
+}
+
+/*
+ * vfe_buf_done - Process write master done interrupt
+ * @vfe: VFE Device
+ * @wm: Write master id
+ */
+void vfe_buf_done(struct vfe_device *vfe, int wm)
+{
+	struct vfe_line *line = &vfe->line[vfe->wm_output_map[wm]];
+	const struct vfe_hw_ops *ops = vfe->res->hw_ops;
+	struct camss_buffer *ready_buf;
+	struct vfe_output *output;
+	unsigned long flags;
+	u32 index;
+	u64 ts = ktime_get_ns();
+
+	spin_lock_irqsave(&vfe->output_lock, flags);
+
+	if (vfe->wm_output_map[wm] == VFE_LINE_NONE) {
+		dev_err_ratelimited(vfe->camss->dev,
+				    "Received wm done for unmapped index\n");
+		goto out_unlock;
+	}
+	output = &vfe->line[vfe->wm_output_map[wm]].output;
+
+	ready_buf = output->buf[0];
+	if (!ready_buf) {
+		dev_err_ratelimited(vfe->camss->dev,
+				    "Missing ready buf %d!\n", output->state);
+		goto out_unlock;
+	}
+
+	ready_buf->vb.vb2_buf.timestamp = ts;
+	ready_buf->vb.sequence = output->sequence++;
+
+	index = 0;
+	output->buf[0] = output->buf[1];
+	if (output->buf[0])
+		index = 1;
+
+	output->buf[index] = vfe_buf_get_pending(output);
+
+	if (output->buf[index]) {
+		ops->vfe_wm_update(vfe, output->wm_idx[0],
+				   output->buf[index]->addr[0],
+				   line);
+		ops->reg_update(vfe, line->id);
+	} else {
+		output->gen2.active_num--;
+	}
+
+	spin_unlock_irqrestore(&vfe->output_lock, flags);
+
+	vb2_buffer_done(&ready_buf->vb.vb2_buf, VB2_BUF_STATE_DONE);
+
+	return;
+
+out_unlock:
+	spin_unlock_irqrestore(&vfe->output_lock, flags);
+}
+
+int vfe_enable_output_v2(struct vfe_line *line)
+{
+	struct vfe_device *vfe = to_vfe(line);
+	struct vfe_output *output = &line->output;
+	const struct vfe_hw_ops *ops = vfe->res->hw_ops;
+	struct media_entity *sensor;
+	unsigned long flags;
+	unsigned int frame_skip = 0;
+	unsigned int i;
+
+	sensor = camss_find_sensor(&line->subdev.entity);
+	if (sensor) {
+		struct v4l2_subdev *subdev = media_entity_to_v4l2_subdev(sensor);
+
+		v4l2_subdev_call(subdev, sensor, g_skip_frames, &frame_skip);
+		/* Max frame skip is 29 frames */
+		if (frame_skip > VFE_FRAME_DROP_VAL - 1)
+			frame_skip = VFE_FRAME_DROP_VAL - 1;
+	}
+
+	spin_lock_irqsave(&vfe->output_lock, flags);
+
+	ops->reg_update_clear(vfe, line->id);
+
+	if (output->state > VFE_OUTPUT_RESERVED) {
+		dev_err(vfe->camss->dev,
+			"Output is not in reserved state %d\n",
+			output->state);
+		spin_unlock_irqrestore(&vfe->output_lock, flags);
+		return -EINVAL;
+	}
+
+	WARN_ON(output->gen2.active_num);
+
+	output->state = VFE_OUTPUT_ON;
+
+	output->sequence = 0;
+	output->wait_reg_update = 0;
+	reinit_completion(&output->reg_update);
+
+	ops->vfe_wm_start(vfe, output->wm_idx[0], line);
+
+	for (i = 0; i < 2; i++) {
+		output->buf[i] = vfe_buf_get_pending(output);
+		if (!output->buf[i])
+			break;
+		output->gen2.active_num++;
+		ops->vfe_wm_update(vfe, output->wm_idx[0],
+				   output->buf[i]->addr[0], line);
+		ops->reg_update(vfe, line->id);
+	}
+
+	spin_unlock_irqrestore(&vfe->output_lock, flags);
+
+	return 0;
+}
+
+/*
+ * vfe_queue_buffer_v2 - Add empty buffer
+ * @vid: Video device structure
+ * @buf: Buffer to be enqueued
+ *
+ * Add an empty buffer - depending on the current number of buffers it will be
+ * put in pending buffer queue or directly given to the hardware to be filled.
+ *
+ * Return 0 on success or a negative error code otherwise
+ */
+int vfe_queue_buffer_v2(struct camss_video *vid,
+			struct camss_buffer *buf)
+{
+	struct vfe_line *line = container_of(vid, struct vfe_line, video_out);
+	struct vfe_device *vfe = to_vfe(line);
+	const struct vfe_hw_ops *ops = vfe->res->hw_ops;
+	struct vfe_output *output;
+	unsigned long flags;
+
+	output = &line->output;
+
+	spin_lock_irqsave(&vfe->output_lock, flags);
+
+	if (output->state == VFE_OUTPUT_ON &&
+	    output->gen2.active_num < 2) {
+		output->buf[output->gen2.active_num++] = buf;
+		ops->vfe_wm_update(vfe, output->wm_idx[0],
+				   buf->addr[0], line);
+		ops->reg_update(vfe, line->id);
+	} else {
+		vfe_buf_add_pending(output, buf);
+	}
+
+	spin_unlock_irqrestore(&vfe->output_lock, flags);
+
+	return 0;
+}
+
+/*
+ * vfe_enable_v2 - Enable streaming on VFE line
+ * @line: VFE line
+ *
+ * Return 0 on success or a negative error code otherwise
+ */
+int vfe_enable_v2(struct vfe_line *line)
+{
+	struct vfe_device *vfe = to_vfe(line);
+	const struct vfe_hw_ops *ops = vfe->res->hw_ops;
+	int ret;
+
+	mutex_lock(&vfe->stream_lock);
+
+	if (vfe->res->hw_ops->enable_irq)
+		ops->enable_irq(vfe);
+
+	vfe->stream_count++;
+
+	mutex_unlock(&vfe->stream_lock);
+
+	ret = vfe_get_output_v2(line);
+	if (ret < 0)
+		goto error_get_output;
+
+	ret = vfe_enable_output_v2(line);
+	if (ret < 0)
+		goto error_enable_output;
+
+	vfe->was_streaming = 1;
+
+	return 0;
+
+error_enable_output:
+	vfe_put_output(line);
+
+error_get_output:
+	mutex_lock(&vfe->stream_lock);
+
+	vfe->stream_count--;
+
+	mutex_unlock(&vfe->stream_lock);
+
+	return ret;
+}
+
+/*
+ * vfe_get_output_v2 - Get vfe output port for corresponding VFE line
+ * @line: VFE line
+ *
+ * Return 0 on success or a negative error code otherwise
+ */
+int vfe_get_output_v2(struct vfe_line *line)
+{
+	struct vfe_device *vfe = to_vfe(line);
+	struct vfe_output *output;
+	unsigned long flags;
+
+	spin_lock_irqsave(&vfe->output_lock, flags);
+
+	output = &line->output;
+	if (output->state > VFE_OUTPUT_RESERVED) {
+		dev_err(vfe->camss->dev, "Output is running\n");
+		goto error;
+	}
+
+	output->wm_num = 1;
+
+	/* Correspondence between VFE line number and WM number.
+	 * line 0 -> RDI 0, line 1 -> RDI1, line 2 -> RDI2, line 3 -> PIX/RDI3
+	 * Note this 1:1 mapping will not work for PIX streams.
+	 */
+	output->wm_idx[0] = line->id;
+	vfe->wm_output_map[line->id] = line->id;
+
+	output->drop_update_idx = 0;
+
+	spin_unlock_irqrestore(&vfe->output_lock, flags);
+
+	return 0;
+
+error:
+	spin_unlock_irqrestore(&vfe->output_lock, flags);
+	output->state = VFE_OUTPUT_OFF;
+
+	return -EINVAL;
+}
+
 int vfe_reset(struct vfe_device *vfe)
 {
 	unsigned long time;
diff --git a/drivers/media/platform/qcom/camss/camss-vfe.h b/drivers/media/platform/qcom/camss/camss-vfe.h
index 10e2cc3c0b83..fcbf4f609129 100644
--- a/drivers/media/platform/qcom/camss/camss-vfe.h
+++ b/drivers/media/platform/qcom/camss/camss-vfe.h
@@ -99,7 +99,7 @@ struct vfe_line {
 struct vfe_device;
 
 struct vfe_hw_ops {
-	void (*enable_irq_common)(struct vfe_device *vfe);
+	void (*enable_irq)(struct vfe_device *vfe);
 	void (*global_reset)(struct vfe_device *vfe);
 	u32 (*hw_version)(struct vfe_device *vfe);
 	irqreturn_t (*isr)(int irq, void *dev);
@@ -114,7 +114,12 @@ struct vfe_hw_ops {
 	int (*vfe_enable)(struct vfe_line *line);
 	int (*vfe_halt)(struct vfe_device *vfe);
 	void (*violation_read)(struct vfe_device *vfe);
+	void (*vfe_wm_start)(struct vfe_device *vfe, u8 wm,
+			     struct vfe_line *line);
 	void (*vfe_wm_stop)(struct vfe_device *vfe, u8 wm);
+	void (*vfe_buf_done)(struct vfe_device *vfe, int port_id);
+	void (*vfe_wm_update)(struct vfe_device *vfe, u8 wm, u32 addr,
+			      struct vfe_line *line);
 };
 
 struct vfe_isr_ops {
@@ -252,4 +257,55 @@ void vfe_put(struct vfe_device *vfe);
  */
 bool vfe_is_lite(struct vfe_device *vfe);
 
+/*
+ * vfe_hw_version - Process write master done interrupt
+ * @vfe: VFE Device
+ *
+ * Return vfe hw version
+ */
+u32 vfe_hw_version(struct vfe_device *vfe);
+/*
+ * vfe_enable - Enable streaming on VFE line
+ * @line: VFE line
+ *
+ * Return 0 on success or a negative error code otherwise
+ */
+int vfe_enable_v2(struct vfe_line *line);
+
+/*
+ * vfe_buf_done - Process write master done interrupt
+ * @vfe: VFE Device
+ * @wm: Write master id
+ */
+void vfe_buf_done(struct vfe_device *vfe, int wm);
+
+/*
+ * vfe_get_output_v2 - Get vfe output line
+ * line: VFE line
+ *
+ * Return 0 on success or a negative error code otherwise
+ */
+int vfe_get_output_v2(struct vfe_line *line);
+
+/*
+ * vfe_enable_output_v2 - Enable vfe output line
+ * line: VFE line
+ *
+ * Return 0 on success or a negative error code otherwise
+ */
+int vfe_enable_output_v2(struct vfe_line *line);
+
+/*
+ * vfe_queue_buffer_v2 - Add empty buffer
+ * @vid: Video device structure
+ * @buf: Buffer to be enqueued
+ *
+ * Add an empty buffer - depending on the current number of buffers it will be
+ * put in pending buffer queue or directly given to the hardware to be filled.
+ *
+ * Return 0 on success or a negative error code otherwise
+ */
+int vfe_queue_buffer_v2(struct camss_video *vid,
+			struct camss_buffer *buf);
+
 #endif /* QC_MSM_CAMSS_VFE_H */
-- 
2.34.1

[PATCH v8 09/16] media: qcom: camss: Add callback API for RUP update and buf done

[Depeng Shao]

The RUP registers and buf done irq are moved from the IFE to CSID register
block on recent CAMSS implementations. Add callbacks structure to wrapper
the location change with minimum logic disruption.

Co-developed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Depeng Shao <quic_depengs@quicinc.com>
---
 .../media/platform/qcom/camss/camss-csid.h    |  9 ++++++++
 drivers/media/platform/qcom/camss/camss.c     | 22 +++++++++++++++++++
 drivers/media/platform/qcom/camss/camss.h     |  3 +++
 3 files changed, 34 insertions(+)

diff --git a/drivers/media/platform/qcom/camss/camss-csid.h b/drivers/media/platform/qcom/camss/camss-csid.h
index f52209b96583..1369e7ea7219 100644
--- a/drivers/media/platform/qcom/camss/camss-csid.h
+++ b/drivers/media/platform/qcom/camss/camss-csid.h
@@ -152,6 +152,14 @@ struct csid_hw_ops {
 	 * @csid: CSID device
 	 */
 	void (*subdev_init)(struct csid_device *csid);
+
+	/*
+	 * reg_update - receive message from other sub device
+	 * @csid: CSID device
+	 * @port_id: Port id
+	 * @is_clear: Indicate if it is clearing reg update or setting reg update
+	 */
+	void (*reg_update)(struct csid_device *csid, int port_id, bool is_clear);
 };
 
 struct csid_subdev_resources {
@@ -168,6 +176,7 @@ struct csid_device {
 	struct media_pad pads[MSM_CSID_PADS_NUM];
 	void __iomem *base;
 	u32 irq;
+	u32 reg_update;
 	char irq_name[30];
 	struct camss_clock *clock;
 	int nclocks;
diff --git a/drivers/media/platform/qcom/camss/camss.c b/drivers/media/platform/qcom/camss/camss.c
index 004a74f6b2f6..f93b520ef038 100644
--- a/drivers/media/platform/qcom/camss/camss.c
+++ b/drivers/media/platform/qcom/camss/camss.c
@@ -2454,6 +2454,28 @@ static int camss_link_entities(struct camss *camss)
 	return ret;
 }
 
+void camss_reg_update(struct camss *camss, int hw_id, int port_id, bool is_clear)
+{
+	struct csid_device *csid;
+
+	if (hw_id < camss->res->csid_num) {
+		csid = &camss->csid[hw_id];
+
+		csid->res->hw_ops->reg_update(csid, port_id, is_clear);
+	}
+}
+
+void camss_buf_done(struct camss *camss, int hw_id, int port_id)
+{
+	struct vfe_device *vfe;
+
+	if (hw_id < camss->res->vfe_num) {
+		vfe = &camss->vfe[hw_id];
+
+		vfe->res->hw_ops->vfe_buf_done(vfe, port_id);
+	}
+}
+
 /*
  * camss_register_entities - Register subdev nodes and create links
  * @camss: CAMSS device
diff --git a/drivers/media/platform/qcom/camss/camss.h b/drivers/media/platform/qcom/camss/camss.h
index 9a046eea334f..bd1d1d2b831d 100644
--- a/drivers/media/platform/qcom/camss/camss.h
+++ b/drivers/media/platform/qcom/camss/camss.h
@@ -162,5 +162,8 @@ void camss_pm_domain_off(struct camss *camss, int id);
 int camss_vfe_get(struct camss *camss, int id);
 void camss_vfe_put(struct camss *camss, int id);
 void camss_delete(struct camss *camss);
+void camss_buf_done(struct camss *camss, int hw_id, int port_id);
+void camss_reg_update(struct camss *camss, int hw_id,
+		      int port_id, bool is_clear);
 
 #endif /* QC_MSM_CAMSS_H */
-- 
2.34.1

[PATCH v8 10/16] media: qcom: camss: Add default case in vfe_src_pad_code

[Depeng Shao]

Add a default case in vfe_src_pad_code to get rid of a compile
warning if a new hw enum is added.

Signed-off-by: Depeng Shao <quic_depengs@quicinc.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 drivers/media/platform/qcom/camss/camss-vfe.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/media/platform/qcom/camss/camss-vfe.c b/drivers/media/platform/qcom/camss/camss-vfe.c
index 818dba4b14dc..2a037860b09f 100644
--- a/drivers/media/platform/qcom/camss/camss-vfe.c
+++ b/drivers/media/platform/qcom/camss/camss-vfe.c
@@ -405,6 +405,10 @@ static u32 vfe_src_pad_code(struct vfe_line *line, u32 sink_code,
 			return sink_code;
 		}
 		break;
+	default:
+		WARN(1, "Unsupported HW version: %x\n",
+		     vfe->camss->res->version);
+		break;
 	}
 	return 0;
 }
-- 
2.34.1

[PATCH v8 11/16] media: qcom: camss: csid: Only add TPG v4l2 ctrl if TPG hardware is available

[Depeng Shao]

There is no CSID TPG on some SoCs, so the v4l2 ctrl in CSID driver
shouldn't be registered. Checking the supported TPG modes to indicate
if the TPG hardware exists or not and only registering v4l2 ctrl for
CSID only when the TPG hardware is present.

Signed-off-by: Depeng Shao <quic_depengs@quicinc.com>
---
 .../media/platform/qcom/camss/camss-csid.c    | 60 +++++++++++--------
 1 file changed, 35 insertions(+), 25 deletions(-)

diff --git a/drivers/media/platform/qcom/camss/camss-csid.c b/drivers/media/platform/qcom/camss/camss-csid.c
index 6cf8e434dc05..e26a69a454a7 100644
--- a/drivers/media/platform/qcom/camss/camss-csid.c
+++ b/drivers/media/platform/qcom/camss/camss-csid.c
@@ -760,11 +760,13 @@ static int csid_set_stream(struct v4l2_subdev *sd, int enable)
 	int ret;
 
 	if (enable) {
-		ret = v4l2_ctrl_handler_setup(&csid->ctrls);
-		if (ret < 0) {
-			dev_err(csid->camss->dev,
-				"could not sync v4l2 controls: %d\n", ret);
-			return ret;
+		if (csid->testgen.nmodes != CSID_PAYLOAD_MODE_DISABLED) {
+			ret = v4l2_ctrl_handler_setup(&csid->ctrls);
+			if (ret < 0) {
+				dev_err(csid->camss->dev,
+					"could not sync v4l2 controls: %d\n", ret);
+				return ret;
+			}
 		}
 
 		if (!csid->testgen.enabled &&
@@ -838,7 +840,8 @@ static void csid_try_format(struct csid_device *csid,
 		break;
 
 	case MSM_CSID_PAD_SRC:
-		if (csid->testgen_mode->cur.val == 0) {
+		if (csid->testgen.nmodes == CSID_PAYLOAD_MODE_DISABLED ||
+		    csid->testgen_mode->cur.val == 0) {
 			/* Test generator is disabled, */
 			/* keep pad formats in sync */
 			u32 code = fmt->code;
@@ -888,7 +891,8 @@ static int csid_enum_mbus_code(struct v4l2_subdev *sd,
 
 		code->code = csid->res->formats->formats[code->index].code;
 	} else {
-		if (csid->testgen_mode->cur.val == 0) {
+		if (csid->testgen.nmodes == CSID_PAYLOAD_MODE_DISABLED ||
+		    csid->testgen_mode->cur.val == 0) {
 			struct v4l2_mbus_framefmt *sink_fmt;
 
 			sink_fmt = __csid_get_format(csid, sd_state,
@@ -1267,7 +1271,8 @@ static int csid_link_setup(struct media_entity *entity,
 
 		/* If test generator is enabled */
 		/* do not allow a link from CSIPHY to CSID */
-		if (csid->testgen_mode->cur.val != 0)
+		if (csid->testgen.nmodes != CSID_PAYLOAD_MODE_DISABLED &&
+		    csid->testgen_mode->cur.val != 0)
 			return -EBUSY;
 
 		sd = media_entity_to_v4l2_subdev(remote->entity);
@@ -1360,24 +1365,27 @@ int msm_csid_register_entity(struct csid_device *csid,
 		 MSM_CSID_NAME, csid->id);
 	v4l2_set_subdevdata(sd, csid);
 
-	ret = v4l2_ctrl_handler_init(&csid->ctrls, 1);
-	if (ret < 0) {
-		dev_err(dev, "Failed to init ctrl handler: %d\n", ret);
-		return ret;
-	}
+	if (csid->testgen.nmodes != CSID_PAYLOAD_MODE_DISABLED) {
+		ret = v4l2_ctrl_handler_init(&csid->ctrls, 1);
+		if (ret < 0) {
+			dev_err(dev, "Failed to init ctrl handler: %d\n", ret);
+			return ret;
+		}
 
-	csid->testgen_mode = v4l2_ctrl_new_std_menu_items(&csid->ctrls,
-				&csid_ctrl_ops, V4L2_CID_TEST_PATTERN,
-				csid->testgen.nmodes, 0, 0,
-				csid->testgen.modes);
+		csid->testgen_mode =
+			v4l2_ctrl_new_std_menu_items(&csid->ctrls,
+						     &csid_ctrl_ops, V4L2_CID_TEST_PATTERN,
+						     csid->testgen.nmodes, 0, 0,
+						     csid->testgen.modes);
 
-	if (csid->ctrls.error) {
-		dev_err(dev, "Failed to init ctrl: %d\n", csid->ctrls.error);
-		ret = csid->ctrls.error;
-		goto free_ctrl;
-	}
+		if (csid->ctrls.error) {
+			dev_err(dev, "Failed to init ctrl: %d\n", csid->ctrls.error);
+			ret = csid->ctrls.error;
+			goto free_ctrl;
+		}
 
-	csid->subdev.ctrl_handler = &csid->ctrls;
+		csid->subdev.ctrl_handler = &csid->ctrls;
+	}
 
 	ret = csid_init_formats(sd, NULL);
 	if (ret < 0) {
@@ -1408,7 +1416,8 @@ int msm_csid_register_entity(struct csid_device *csid,
 media_cleanup:
 	media_entity_cleanup(&sd->entity);
 free_ctrl:
-	v4l2_ctrl_handler_free(&csid->ctrls);
+	if (csid->testgen.nmodes != CSID_PAYLOAD_MODE_DISABLED)
+		v4l2_ctrl_handler_free(&csid->ctrls);
 
 	return ret;
 }
@@ -1421,7 +1430,8 @@ void msm_csid_unregister_entity(struct csid_device *csid)
 {
 	v4l2_device_unregister_subdev(&csid->subdev);
 	media_entity_cleanup(&csid->subdev.entity);
-	v4l2_ctrl_handler_free(&csid->ctrls);
+	if (csid->testgen.nmodes != CSID_PAYLOAD_MODE_DISABLED)
+		v4l2_ctrl_handler_free(&csid->ctrls);
 }
 
 inline bool csid_is_lite(struct csid_device *csid)
-- 
2.34.1

[PATCH v8 12/16] dt-bindings: media: camss: Add qcom,sm8550-camss binding

[Depeng Shao]

Add bindings for qcom,sm8550-camss in order to support the camera
subsystem for sm8550.

Co-developed-by: Yongsheng Li <quic_yon@quicinc.com>
Signed-off-by: Yongsheng Li <quic_yon@quicinc.com>
Signed-off-by: Depeng Shao <quic_depengs@quicinc.com>
---
 .../bindings/media/qcom,sm8550-camss.yaml     | 597 ++++++++++++++++++
 1 file changed, 597 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/qcom,sm8550-camss.yaml

diff --git a/Documentation/devicetree/bindings/media/qcom,sm8550-camss.yaml b/Documentation/devicetree/bindings/media/qcom,sm8550-camss.yaml
new file mode 100644
index 000000000000..cd34f14916b4
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/qcom,sm8550-camss.yaml
@@ -0,0 +1,597 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/qcom,sm8550-camss.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm SM8550 Camera Subsystem (CAMSS)
+
+maintainers:
+  - Depeng Shao <quic_depengs@quicinc.com>
+
+description:
+  The CAMSS IP is a CSI decoder and ISP present on Qualcomm platforms.
+
+properties:
+  compatible:
+    const: qcom,sm8550-camss
+
+  reg:
+    maxItems: 19
+
+  reg-names:
+    items:
+      - const: csid0
+      - const: csid1
+      - const: csid2
+      - const: csid_lite0
+      - const: csid_lite1
+      - const: csid_wrapper
+      - const: csiphy0
+      - const: csiphy1
+      - const: csiphy2
+      - const: csiphy3
+      - const: csiphy4
+      - const: csiphy5
+      - const: csiphy6
+      - const: csiphy7
+      - const: vfe0
+      - const: vfe1
+      - const: vfe2
+      - const: vfe_lite0
+      - const: vfe_lite1
+
+  clocks:
+    maxItems: 36
+
+  clock-names:
+    items:
+      - const: camnoc_axi
+      - const: cpas_ahb
+      - const: cpas_fast_ahb_clk
+      - const: cpas_ife_lite
+      - const: cpas_vfe0
+      - const: cpas_vfe1
+      - const: cpas_vfe2
+      - const: csid
+      - const: csiphy0
+      - const: csiphy0_timer
+      - const: csiphy1
+      - const: csiphy1_timer
+      - const: csiphy2
+      - const: csiphy2_timer
+      - const: csiphy3
+      - const: csiphy3_timer
+      - const: csiphy4
+      - const: csiphy4_timer
+      - const: csiphy5
+      - const: csiphy5_timer
+      - const: csiphy6
+      - const: csiphy6_timer
+      - const: csiphy7
+      - const: csiphy7_timer
+      - const: csiphy_rx
+      - const: gcc_axi_hf
+      - const: vfe0
+      - const: vfe0_fast_ahb
+      - const: vfe1
+      - const: vfe1_fast_ahb
+      - const: vfe2
+      - const: vfe2_fast_ahb
+      - const: vfe_lite
+      - const: vfe_lite_ahb
+      - const: vfe_lite_cphy_rx
+      - const: vfe_lite_csid
+
+  interrupts:
+    maxItems: 18
+
+  interrupt-names:
+    items:
+      - const: csid0
+      - const: csid1
+      - const: csid2
+      - const: csid_lite0
+      - const: csid_lite1
+      - const: csiphy0
+      - const: csiphy1
+      - const: csiphy2
+      - const: csiphy3
+      - const: csiphy4
+      - const: csiphy5
+      - const: csiphy6
+      - const: csiphy7
+      - const: vfe0
+      - const: vfe1
+      - const: vfe2
+      - const: vfe_lite0
+      - const: vfe_lite1
+
+  interconnects:
+    maxItems: 2
+
+  interconnect-names:
+    items:
+      - const: ahb
+      - const: hf_0_mnoc
+
+  iommus:
+    maxItems: 1
+
+  power-domains:
+    items:
+      - description: IFE0 GDSC - Image Front End, Global Distributed Switch Controller.
+      - description: IFE1 GDSC - Image Front End, Global Distributed Switch Controller.
+      - description: IFE2 GDSC - Image Front End, Global Distributed Switch Controller.
+      - description: Titan GDSC - Titan ISP Block, Global Distributed Switch Controller.
+
+  power-domain-names:
+    items:
+      - const: ife0
+      - const: ife1
+      - const: ife2
+      - const: top
+
+  vdda-phy-supply:
+    description:
+      Phandle to a regulator supply to PHY core block.
+
+  vdda-pll-supply:
+    description:
+      Phandle to 1.2V regulator supply to PHY refclk pll block.
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    description:
+      CSI input ports.
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description:
+          Input port for receiving CSI data on CSI0.
+
+        properties:
+          endpoint:
+            $ref: video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              clock-lanes:
+                maxItems: 1
+
+              data-lanes:
+                minItems: 1
+                maxItems: 4
+
+              bus-type:
+                enum:
+                  - 1 # MEDIA_BUS_TYPE_CSI2_CPHY
+                  - 4 # MEDIA_BUS_TYPE_CSI2_DPHY
+
+            required:
+              - clock-lanes
+              - data-lanes
+
+      port@1:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description:
+          Input port for receiving CSI data on CSI1.
+
+        properties:
+          endpoint:
+            $ref: video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              clock-lanes:
+                maxItems: 1
+
+              data-lanes:
+                minItems: 1
+                maxItems: 4
+
+              bus-type:
+                enum:
+                  - 1 # MEDIA_BUS_TYPE_CSI2_CPHY
+                  - 4 # MEDIA_BUS_TYPE_CSI2_DPHY
+
+            required:
+              - clock-lanes
+              - data-lanes
+
+      port@2:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description:
+          Input port for receiving CSI data on CSI2.
+
+        properties:
+          endpoint:
+            $ref: video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              clock-lanes:
+                maxItems: 1
+
+              data-lanes:
+                minItems: 1
+                maxItems: 4
+
+              bus-type:
+                enum:
+                  - 1 # MEDIA_BUS_TYPE_CSI2_CPHY
+                  - 4 # MEDIA_BUS_TYPE_CSI2_DPHY
+
+            required:
+              - clock-lanes
+              - data-lanes
+
+      port@3:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description:
+          Input port for receiving CSI data on CSI3.
+
+        properties:
+          endpoint:
+            $ref: video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              clock-lanes:
+                maxItems: 1
+
+              data-lanes:
+                minItems: 1
+                maxItems: 4
+
+              bus-type:
+                enum:
+                  - 1 # MEDIA_BUS_TYPE_CSI2_CPHY
+                  - 4 # MEDIA_BUS_TYPE_CSI2_DPHY
+
+            required:
+              - clock-lanes
+              - data-lanes
+
+      port@4:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description:
+          Input port for receiving CSI data on CSI4.
+
+        properties:
+          endpoint:
+            $ref: video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              clock-lanes:
+                maxItems: 1
+
+              data-lanes:
+                minItems: 1
+                maxItems: 4
+
+              bus-type:
+                enum:
+                  - 1 # MEDIA_BUS_TYPE_CSI2_CPHY
+                  - 4 # MEDIA_BUS_TYPE_CSI2_DPHY
+
+            required:
+              - clock-lanes
+              - data-lanes
+
+      port@5:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description:
+          Input port for receiving CSI data on CSI5.
+
+        properties:
+          endpoint:
+            $ref: video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              clock-lanes:
+                maxItems: 1
+
+              data-lanes:
+                minItems: 1
+                maxItems: 4
+
+              bus-type:
+                enum:
+                  - 1 # MEDIA_BUS_TYPE_CSI2_CPHY
+                  - 4 # MEDIA_BUS_TYPE_CSI2_DPHY
+
+            required:
+              - clock-lanes
+              - data-lanes
+
+      port@6:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description:
+          Input port for receiving CSI data on CSI6.
+
+        properties:
+          endpoint:
+            $ref: video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              clock-lanes:
+                maxItems: 1
+
+              data-lanes:
+                minItems: 1
+                maxItems: 4
+
+              bus-type:
+                enum:
+                  - 1 # MEDIA_BUS_TYPE_CSI2_CPHY
+                  - 4 # MEDIA_BUS_TYPE_CSI2_DPHY
+
+            required:
+              - clock-lanes
+              - data-lanes
+
+      port@7:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description:
+          Input port for receiving CSI data on CSI7.
+
+        properties:
+          endpoint:
+            $ref: video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              clock-lanes:
+                maxItems: 1
+
+              data-lanes:
+                minItems: 1
+                maxItems: 4
+
+              bus-type:
+                enum:
+                  - 1 # MEDIA_BUS_TYPE_CSI2_CPHY
+                  - 4 # MEDIA_BUS_TYPE_CSI2_DPHY
+
+            required:
+              - clock-lanes
+              - data-lanes
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - clocks
+  - clock-names
+  - interrupts
+  - interrupt-names
+  - interconnects
+  - interconnect-names
+  - iommus
+  - power-domains
+  - power-domain-names
+  - vdda-phy-supply
+  - vdda-pll-supply
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,rpmh.h>
+    #include <dt-bindings/clock/qcom,sm8550-camcc.h>
+    #include <dt-bindings/clock/qcom,sm8550-gcc.h>
+    #include <dt-bindings/interconnect/qcom,icc.h>
+    #include <dt-bindings/interconnect/qcom,sm8550-rpmh.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/power/qcom-rpmpd.h>
+
+    soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        isp@acb7000 {
+            compatible = "qcom,sm8550-camss";
+
+            reg = <0 0x0acb7000 0 0xd00>,
+                  <0 0x0acb9000 0 0xd00>,
+                  <0 0x0acbb000 0 0xd00>,
+                  <0 0x0acca000 0 0xa00>,
+                  <0 0x0acce000 0 0xa00>,
+                  <0 0x0acb6000 0 0x1000>,
+                  <0 0x0ace4000 0 0x2000>,
+                  <0 0x0ace6000 0 0x2000>,
+                  <0 0x0ace8000 0 0x2000>,
+                  <0 0x0acea000 0 0x2000>,
+                  <0 0x0acec000 0 0x2000>,
+                  <0 0x0acee000 0 0x2000>,
+                  <0 0x0acf0000 0 0x2000>,
+                  <0 0x0acf2000 0 0x2000>,
+                  <0 0x0ac62000 0 0xf000>,
+                  <0 0x0ac71000 0 0xf000>,
+                  <0 0x0ac80000 0 0xf000>,
+                  <0 0x0accb000 0 0x1800>,
+                  <0 0x0accf000 0 0x1800>;
+            reg-names = "csid0",
+                        "csid1",
+                        "csid2",
+                        "csid_lite0",
+                        "csid_lite1",
+                        "csid_wrapper",
+                        "csiphy0",
+                        "csiphy1",
+                        "csiphy2",
+                        "csiphy3",
+                        "csiphy4",
+                        "csiphy5",
+                        "csiphy6",
+                        "csiphy7",
+                        "vfe0",
+                        "vfe1",
+                        "vfe2",
+                        "vfe_lite0",
+                        "vfe_lite1";
+
+            clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>,
+                     <&camcc CAM_CC_CPAS_AHB_CLK>,
+                     <&camcc CAM_CC_CPAS_FAST_AHB_CLK>,
+                     <&camcc CAM_CC_CPAS_IFE_LITE_CLK>,
+                     <&camcc CAM_CC_CPAS_IFE_0_CLK>,
+                     <&camcc CAM_CC_CPAS_IFE_1_CLK>,
+                     <&camcc CAM_CC_CPAS_IFE_2_CLK>,
+                     <&camcc CAM_CC_CSID_CLK>,
+                     <&camcc CAM_CC_CSIPHY0_CLK>,
+                     <&camcc CAM_CC_CSI0PHYTIMER_CLK>,
+                     <&camcc CAM_CC_CSIPHY1_CLK>,
+                     <&camcc CAM_CC_CSI1PHYTIMER_CLK>,
+                     <&camcc CAM_CC_CSIPHY2_CLK>,
+                     <&camcc CAM_CC_CSI2PHYTIMER_CLK>,
+                     <&camcc CAM_CC_CSIPHY3_CLK>,
+                     <&camcc CAM_CC_CSI3PHYTIMER_CLK>,
+                     <&camcc CAM_CC_CSIPHY4_CLK>,
+                     <&camcc CAM_CC_CSI4PHYTIMER_CLK>,
+                     <&camcc CAM_CC_CSIPHY5_CLK>,
+                     <&camcc CAM_CC_CSI5PHYTIMER_CLK>,
+                     <&camcc CAM_CC_CSIPHY6_CLK>,
+                     <&camcc CAM_CC_CSI6PHYTIMER_CLK>,
+                     <&camcc CAM_CC_CSIPHY7_CLK>,
+                     <&camcc CAM_CC_CSI7PHYTIMER_CLK>,
+                     <&camcc CAM_CC_CSID_CSIPHY_RX_CLK>,
+                     <&gcc GCC_CAMERA_HF_AXI_CLK>,
+                     <&camcc CAM_CC_IFE_0_CLK>,
+                     <&camcc CAM_CC_IFE_0_FAST_AHB_CLK>,
+                     <&camcc CAM_CC_IFE_1_CLK>,
+                     <&camcc CAM_CC_IFE_1_FAST_AHB_CLK>,
+                     <&camcc CAM_CC_IFE_2_CLK>,
+                     <&camcc CAM_CC_IFE_2_FAST_AHB_CLK>,
+                     <&camcc CAM_CC_IFE_LITE_CLK>,
+                     <&camcc CAM_CC_IFE_LITE_AHB_CLK>,
+                     <&camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>,
+                     <&camcc CAM_CC_IFE_LITE_CSID_CLK>;
+            clock-names = "camnoc_axi",
+                          "cpas_ahb",
+                          "cpas_fast_ahb_clk",
+                          "cpas_ife_lite",
+                          "cpas_vfe0",
+                          "cpas_vfe1",
+                          "cpas_vfe2",
+                          "csid",
+                          "csiphy0",
+                          "csiphy0_timer",
+                          "csiphy1",
+                          "csiphy1_timer",
+                          "csiphy2",
+                          "csiphy2_timer",
+                          "csiphy3",
+                          "csiphy3_timer",
+                          "csiphy4",
+                          "csiphy4_timer",
+                          "csiphy5",
+                          "csiphy5_timer",
+                          "csiphy6",
+                          "csiphy6_timer",
+                          "csiphy7",
+                          "csiphy7_timer",
+                          "csiphy_rx",
+                          "gcc_axi_hf",
+                          "vfe0",
+                          "vfe0_fast_ahb",
+                          "vfe1",
+                          "vfe1_fast_ahb",
+                          "vfe2",
+                          "vfe2_fast_ahb",
+                          "vfe_lite",
+                          "vfe_lite_ahb",
+                          "vfe_lite_cphy_rx",
+                          "vfe_lite_csid";
+
+            interrupts = <GIC_SPI 601 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 603 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 431 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 605 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 376 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 478 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 479 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 448 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 122 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 89 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 278 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 277 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 602 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 604 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 688 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 606 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 377 IRQ_TYPE_EDGE_RISING>;
+            interrupt-names = "csid0",
+                              "csid1",
+                              "csid2",
+                              "csid_lite0",
+                              "csid_lite1",
+                              "csiphy0",
+                              "csiphy1",
+                              "csiphy2",
+                              "csiphy3",
+                              "csiphy4",
+                              "csiphy5",
+                              "csiphy6",
+                              "csiphy7",
+                              "vfe0",
+                              "vfe1",
+                              "vfe2",
+                              "vfe_lite0",
+                              "vfe_lite1";
+
+            interconnects = <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY
+                             &config_noc SLAVE_CAMERA_CFG QCOM_ICC_TAG_ACTIVE_ONLY>,
+                            <&mmss_noc MASTER_CAMNOC_HF QCOM_ICC_TAG_ALWAYS
+                             &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+            interconnect-names = "ahb",
+                                 "hf_0_mnoc";
+
+            iommus = <&apps_smmu 0x800 0x20>;
+
+            power-domains = <&camcc CAM_CC_IFE_0_GDSC>,
+                            <&camcc CAM_CC_IFE_1_GDSC>,
+                            <&camcc CAM_CC_IFE_2_GDSC>,
+                            <&camcc CAM_CC_TITAN_TOP_GDSC>;
+            power-domain-names = "ife0",
+                                 "ife1",
+                                 "ife2",
+                                 "top";
+
+            vdda-phy-supply = <&vreg_l1e_0p88>;
+            vdda-pll-supply = <&vreg_l3e_1p2>;
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+                    #address-cells = <1>;
+                    #size-cells = <0>;
+
+                    csiphy_ep0: endpoint@0 {
+                        reg = <0>;
+                        clock-lanes = <7>;
+                        data-lanes = <0 1>;
+                        remote-endpoint = <&sensor_ep>;
+                    };
+                };
+            };
+        };
+    };
-- 
2.34.1

[PATCH v8 13/16] media: qcom: camss: Add sm8550 compatible

[Depeng Shao]

Add CAMSS_8550 enum, sm8550 compatible and sm8550 camss drvier private
data, the private data just include some basic information now, later
changes will enumerate with csiphy, csid and vfe resources.

Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Depeng Shao <quic_depengs@quicinc.com>
---
 drivers/media/platform/qcom/camss/camss.c | 22 ++++++++++++++++++++++
 drivers/media/platform/qcom/camss/camss.h |  1 +
 2 files changed, 23 insertions(+)

diff --git a/drivers/media/platform/qcom/camss/camss.c b/drivers/media/platform/qcom/camss/camss.c
index f93b520ef038..2705e0bc046b 100644
--- a/drivers/media/platform/qcom/camss/camss.c
+++ b/drivers/media/platform/qcom/camss/camss.c
@@ -1938,6 +1938,19 @@ static const struct resources_icc icc_res_sc8280xp[] = {
 	},
 };
 
+static const struct resources_icc icc_res_sm8550[] = {
+	{
+		.name = "ahb",
+		.icc_bw_tbl.avg = 2097152,
+		.icc_bw_tbl.peak = 2097152,
+	},
+	{
+		.name = "hf_0_mnoc",
+		.icc_bw_tbl.avg = 2097152,
+		.icc_bw_tbl.peak = 2097152,
+	},
+};
+
 /*
  * camss_add_clock_margin - Add margin to clock frequency rate
  * @rate: Clock frequency rate
@@ -3025,6 +3038,14 @@ static const struct camss_resources sc7280_resources = {
 	.link_entities = camss_link_entities
 };
 
+static const struct camss_resources sm8550_resources = {
+	.version = CAMSS_8550,
+	.pd_name = "top",
+	.icc_res = icc_res_sm8550,
+	.icc_path_num = ARRAY_SIZE(icc_res_sm8550),
+	.link_entities = camss_link_entities
+};
+
 static const struct of_device_id camss_dt_match[] = {
 	{ .compatible = "qcom,msm8916-camss", .data = &msm8916_resources },
 	{ .compatible = "qcom,msm8953-camss", .data = &msm8953_resources },
@@ -3034,6 +3055,7 @@ static const struct of_device_id camss_dt_match[] = {
 	{ .compatible = "qcom,sdm660-camss", .data = &sdm660_resources },
 	{ .compatible = "qcom,sdm845-camss", .data = &sdm845_resources },
 	{ .compatible = "qcom,sm8250-camss", .data = &sm8250_resources },
+	{ .compatible = "qcom,sm8550-camss", .data = &sm8550_resources },
 	{ }
 };
 
diff --git a/drivers/media/platform/qcom/camss/camss.h b/drivers/media/platform/qcom/camss/camss.h
index bd1d1d2b831d..58fc61e7cf7a 100644
--- a/drivers/media/platform/qcom/camss/camss.h
+++ b/drivers/media/platform/qcom/camss/camss.h
@@ -85,6 +85,7 @@ enum camss_version {
 	CAMSS_8250,
 	CAMSS_8280XP,
 	CAMSS_845,
+	CAMSS_8550,
 };
 
 enum icc_count {
-- 
2.34.1

[PATCH v8 14/16] media: qcom: camss: csiphy-3ph: Add Gen2 v2.1.2 two-phase MIPI CSI-2 DPHY support

[Depeng Shao]

Add a PHY configuration sequence and PHY resource for the sm8550 which
uses a Qualcomm Gen 2 version 2.1.2 CSI-2 PHY.

The PHY can be configured as two phase or three phase in C-PHY or D-PHY
mode. This configuration supports two-phase D-PHY mode.

Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Depeng Shao <quic_depengs@quicinc.com>
---
 .../qcom/camss/camss-csiphy-3ph-1-0.c         | 111 ++++++++++++++++++
 drivers/media/platform/qcom/camss/camss.c     | 109 +++++++++++++++++
 2 files changed, 220 insertions(+)

diff --git a/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c b/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c
index b5a116ced6a7..a6cc957b986e 100644
--- a/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c
+++ b/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c
@@ -318,6 +318,111 @@ csiphy_lane_regs lane_regs_sm8250[] = {
 	{0x0884, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
 };
 
+/* GEN2 2.1.2 2PH DPHY mode */
+static const struct
+csiphy_lane_regs lane_regs_sm8550[] = {
+	{0x0E90, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0E98, 0x08, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0E94, 0x07, 0x01, CSIPHY_DEFAULT_PARAMS},
+	{0x00A0, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0090, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0098, 0x08, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0094, 0x07, 0x01, CSIPHY_DEFAULT_PARAMS},
+	{0x0494, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x04A0, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0490, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0498, 0x08, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0494, 0x07, 0x01, CSIPHY_DEFAULT_PARAMS},
+	{0x0894, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x08A0, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0890, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0898, 0x08, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0894, 0x07, 0x01, CSIPHY_DEFAULT_PARAMS},
+	{0x0C94, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0CA0, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0C90, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0C98, 0x08, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0C94, 0x07, 0x01, CSIPHY_DEFAULT_PARAMS},
+	{0x0E30, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0E28, 0x04, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0E00, 0x80, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0E0C, 0xFF, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0E38, 0x1F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0E2C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0E34, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0E1C, 0x0A, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0E14, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0E3C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0E04, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0E20, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0E08, 0x10, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{0x0E10, 0x52, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0030, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0000, 0x8E, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0038, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x002C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0034, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x001C, 0x0A, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0014, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x003C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0004, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0020, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0008, 0x10, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{0x0010, 0x52, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0430, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0400, 0x8E, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0438, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x042C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0434, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x041C, 0x0A, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0414, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x043C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0404, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0420, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0408, 0x10, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{0x0410, 0x52, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0830, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0800, 0x8E, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0838, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x082C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0834, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x081C, 0x0A, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0814, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x083C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0804, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0820, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0808, 0x10, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{0x0810, 0x52, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0C30, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0C00, 0x8E, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0C38, 0xFE, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0C2C, 0x01, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0C34, 0x0F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0C1C, 0x0A, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0C14, 0x60, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0C3C, 0xB8, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0C04, 0x0C, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0C20, 0x00, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0C08, 0x10, 0x00, CSIPHY_SETTLE_CNT_LOWER_BYTE},
+	{0x0C10, 0x52, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0094, 0xD7, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x005C, 0x04, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0060, 0xBD, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0064, 0x7F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0494, 0xD7, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x045C, 0x04, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0460, 0xBD, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0464, 0x7F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0894, 0xD7, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x085C, 0x04, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0860, 0xBD, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0864, 0x7F, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0C94, 0xD7, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0C5C, 0x04, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0C60, 0xBD, 0x00, CSIPHY_DEFAULT_PARAMS},
+	{0x0C64, 0x7F, 0x00, CSIPHY_DEFAULT_PARAMS},
+};
+
 static void csiphy_hw_version_read(struct csiphy_device *csiphy,
 				   struct device *dev)
 {
@@ -520,6 +625,7 @@ static bool csiphy_is_gen2(u32 version)
 	case CAMSS_8250:
 	case CAMSS_8280XP:
 	case CAMSS_845:
+	case CAMSS_8550:
 		ret = true;
 		break;
 	}
@@ -608,6 +714,11 @@ static int csiphy_init(struct csiphy_device *csiphy)
 		regs->lane_regs = &lane_regs_sc8280xp[0];
 		regs->lane_array_size = ARRAY_SIZE(lane_regs_sc8280xp);
 		break;
+	case CAMSS_8550:
+		regs->lane_regs = &lane_regs_sm8550[0];
+		regs->lane_array_size = ARRAY_SIZE(lane_regs_sm8550);
+		regs->offset = 0x1000;
+		break;
 	default:
 		WARN(1, "unknown csiphy version\n");
 		return -ENODEV;
diff --git a/drivers/media/platform/qcom/camss/camss.c b/drivers/media/platform/qcom/camss/camss.c
index 2705e0bc046b..39f7fa6e9f28 100644
--- a/drivers/media/platform/qcom/camss/camss.c
+++ b/drivers/media/platform/qcom/camss/camss.c
@@ -1938,6 +1938,113 @@ static const struct resources_icc icc_res_sc8280xp[] = {
 	},
 };
 
+static const struct camss_subdev_resources csiphy_res_8550[] = {
+	/* CSIPHY0 */
+	{
+		.regulators = { "vdda-phy", "vdda-pll" },
+		.clock = { "csiphy0", "csiphy0_timer" },
+		.clock_rate = { { 400000000, 480000000 },
+				{ 400000000 } },
+		.reg = { "csiphy0" },
+		.interrupt = { "csiphy0" },
+		.csiphy = {
+			.hw_ops = &csiphy_ops_3ph_1_0,
+			.formats = &csiphy_formats_sdm845
+		}
+	},
+	/* CSIPHY1 */
+	{
+		.regulators = { "vdda-phy", "vdda-pll" },
+		.clock = { "csiphy1", "csiphy1_timer" },
+		.clock_rate = { { 400000000, 480000000 },
+				{ 400000000 } },
+		.reg = { "csiphy1" },
+		.interrupt = { "csiphy1" },
+		.csiphy = {
+			.hw_ops = &csiphy_ops_3ph_1_0,
+			.formats = &csiphy_formats_sdm845
+		}
+	},
+	/* CSIPHY2 */
+	{
+		.regulators = { "vdda-phy", "vdda-pll" },
+		.clock = { "csiphy2", "csiphy2_timer" },
+		.clock_rate = { { 400000000, 480000000 },
+				{ 400000000 } },
+		.reg = { "csiphy2" },
+		.interrupt = { "csiphy2" },
+		.csiphy = {
+			.hw_ops = &csiphy_ops_3ph_1_0,
+			.formats = &csiphy_formats_sdm845
+		}
+	},
+	/* CSIPHY3 */
+	{
+		.regulators = { "vdda-phy", "vdda-pll" },
+		.clock = { "csiphy3", "csiphy3_timer" },
+		.clock_rate = { { 400000000, 480000000 },
+				{ 400000000 } },
+		.reg = { "csiphy3" },
+		.interrupt = { "csiphy3" },
+		.csiphy = {
+			.hw_ops = &csiphy_ops_3ph_1_0,
+			.formats = &csiphy_formats_sdm845
+		}
+	},
+	/* CSIPHY4 */
+	{
+		.regulators = { "vdda-phy", "vdda-pll" },
+		.clock = { "csiphy4", "csiphy4_timer" },
+		.clock_rate = { { 400000000, 480000000 },
+				{ 400000000 } },
+		.reg = { "csiphy4" },
+		.interrupt = { "csiphy4" },
+		.csiphy = {
+			.hw_ops = &csiphy_ops_3ph_1_0,
+			.formats = &csiphy_formats_sdm845
+		}
+	},
+	/* CSIPHY5 */
+	{
+		.regulators = { "vdda-phy", "vdda-pll" },
+		.clock = { "csiphy5", "csiphy5_timer" },
+		.clock_rate = { { 400000000, 480000000 },
+				{ 400000000 } },
+		.reg = { "csiphy5" },
+		.interrupt = { "csiphy5" },
+		.csiphy = {
+			.hw_ops = &csiphy_ops_3ph_1_0,
+			.formats = &csiphy_formats_sdm845
+		}
+	},
+	/* CSIPHY6 */
+	{
+		.regulators = { "vdda-phy", "vdda-pll" },
+		.clock = { "csiphy6", "csiphy6_timer" },
+		.clock_rate = { { 400000000, 480000000 },
+				{ 400000000 } },
+		.reg = { "csiphy6" },
+		.interrupt = { "csiphy6" },
+		.csiphy = {
+			.hw_ops = &csiphy_ops_3ph_1_0,
+			.formats = &csiphy_formats_sdm845
+		}
+	},
+	/* CSIPHY7 */
+	{
+		.regulators = { "vdda-phy", "vdda-pll" },
+		.clock = { "csiphy7", "csiphy7_timer" },
+		.clock_rate = { { 400000000, 480000000 },
+				{ 400000000 } },
+		.reg = { "csiphy7" },
+		.interrupt = { "csiphy7" },
+		.csiphy = {
+			.hw_ops = &csiphy_ops_3ph_1_0,
+			.formats = &csiphy_formats_sdm845
+		}
+	}
+};
+
 static const struct resources_icc icc_res_sm8550[] = {
 	{
 		.name = "ahb",
@@ -3041,8 +3148,10 @@ static const struct camss_resources sc7280_resources = {
 static const struct camss_resources sm8550_resources = {
 	.version = CAMSS_8550,
 	.pd_name = "top",
+	.csiphy_res = csiphy_res_8550,
 	.icc_res = icc_res_sm8550,
 	.icc_path_num = ARRAY_SIZE(icc_res_sm8550),
+	.csiphy_num = ARRAY_SIZE(csiphy_res_8550),
 	.link_entities = camss_link_entities
 };
 
-- 
2.34.1

[PATCH v8 15/16] media: qcom: camss: Add CSID 780 support

[Depeng Shao]

The CSID in sm8550 is version 780, it has new register offset
and new functionality. The buf done irq, register update and
reset are moved to CSID 780.

Co-developed-by: Yongsheng Li <quic_yon@quicinc.com>
Signed-off-by: Yongsheng Li <quic_yon@quicinc.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Depeng Shao <quic_depengs@quicinc.com>
---
 drivers/media/platform/qcom/camss/Makefile    |   1 +
 .../platform/qcom/camss/camss-csid-780.c      | 337 ++++++++++++++++++
 .../platform/qcom/camss/camss-csid-780.h      |  25 ++
 .../media/platform/qcom/camss/camss-csid.h    |   1 +
 drivers/media/platform/qcom/camss/camss.c     |  85 +++++
 5 files changed, 449 insertions(+)
 create mode 100644 drivers/media/platform/qcom/camss/camss-csid-780.c
 create mode 100644 drivers/media/platform/qcom/camss/camss-csid-780.h

diff --git a/drivers/media/platform/qcom/camss/Makefile b/drivers/media/platform/qcom/camss/Makefile
index e636968a1126..9a723e8712a2 100644
--- a/drivers/media/platform/qcom/camss/Makefile
+++ b/drivers/media/platform/qcom/camss/Makefile
@@ -7,6 +7,7 @@ qcom-camss-objs += \
 		camss-csid-4-1.o \
 		camss-csid-4-7.o \
 		camss-csid-gen2.o \
+		camss-csid-780.o \
 		camss-csiphy-2ph-1-0.o \
 		camss-csiphy-3ph-1-0.o \
 		camss-csiphy.o \
diff --git a/drivers/media/platform/qcom/camss/camss-csid-780.c b/drivers/media/platform/qcom/camss/camss-csid-780.c
new file mode 100644
index 000000000000..3132b2415aba
--- /dev/null
+++ b/drivers/media/platform/qcom/camss/camss-csid-780.c
@@ -0,0 +1,337 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Qualcomm MSM Camera Subsystem - CSID (CSI Decoder) Module
+ *
+ * Copyright (c) 2024-2025 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/of.h>
+
+#include "camss.h"
+#include "camss-csid.h"
+#include "camss-csid-780.h"
+
+#define CSID_IO_PATH_CFG0(csid)		(0x4 * (csid))
+#define		OUTPUT_IFE_EN			0x100
+#define		INTERNAL_CSID			1
+
+#define CSID_RST_CFG			0xC
+#define		RST_MODE			BIT(0)
+#define		RST_LOCATION			BIT(4)
+
+#define CSID_RST_CMD			0x10
+#define		SELECT_HW_RST			BIT(0)
+#define		SELECT_IRQ_RST			BIT(2)
+
+#define CSID_IRQ_CMD			0x14
+#define		IRQ_CMD_CLEAR			BIT(0)
+
+#define CSID_RUP_AUP_CMD		0x18
+#define		CSID_RUP_AUP_RDI(rdi)		((BIT(4) | BIT(20)) << (rdi))
+
+#define CSID_TOP_IRQ_STATUS		0x7C
+#define		 TOP_IRQ_STATUS_RESET_DONE	BIT(0)
+
+#define CSID_TOP_IRQ_MASK		0x80
+#define CSID_TOP_IRQ_CLEAR		0x84
+#define CSID_TOP_IRQ_SET		0x88
+
+#define CSID_CSI2_RX_IRQ_STATUS		0x9C
+#define CSID_CSI2_RX_IRQ_MASK		0xA0
+#define CSID_CSI2_RX_IRQ_CLEAR		0xA4
+#define CSID_CSI2_RX_IRQ_SET		0xA8
+
+#define CSID_BUF_DONE_IRQ_STATUS	0x8C
+#define		BUF_DONE_IRQ_STATUS_RDI_OFFSET	(csid_is_lite(csid) ? 1 : 14)
+#define CSID_BUF_DONE_IRQ_MASK		0x90
+#define CSID_BUF_DONE_IRQ_CLEAR		0x94
+#define CSID_BUF_DONE_IRQ_SET		0x98
+
+#define CSID_CSI2_RDIN_IRQ_STATUS(rdi)	(0xEC + 0x10 * (rdi))
+#define		RUP_DONE_IRQ_STATUS		BIT(23)
+
+#define CSID_CSI2_RDIN_IRQ_CLEAR(rdi)	(0xF4 + 0x10 * (rdi))
+#define CSID_CSI2_RDIN_IRQ_SET(rdi)	(0xF8 + 0x10 * (rdi))
+
+#define CSID_CSI2_RX_CFG0		0x200
+#define		CSI2_RX_CFG0_NUM_ACTIVE_LANES	0
+#define		CSI2_RX_CFG0_DL0_INPUT_SEL	4
+#define		CSI2_RX_CFG0_PHY_NUM_SEL	20
+
+#define CSID_CSI2_RX_CFG1		0x204
+#define		CSI2_RX_CFG1_ECC_CORRECTION_EN	BIT(0)
+#define		CSI2_RX_CFG1_VC_MODE		BIT(2)
+
+#define CSID_RDI_CFG0(rdi)		(0x500 + 0x100 * (rdi))
+#define		RDI_CFG0_TIMESTAMP_EN		BIT(6)
+#define		RDI_CFG0_TIMESTAMP_STB_SEL	BIT(8)
+#define		RDI_CFG0_DECODE_FORMAT		12
+#define		RDI_CFG0_DT			16
+#define		RDI_CFG0_VC			22
+#define		RDI_CFG0_DT_ID			27
+#define		RDI_CFG0_EN			BIT(31)
+
+#define CSID_RDI_CTRL(rdi)		(0x504 + 0x100 * (rdi))
+#define		RDI_CTRL_START_CMD		BIT(0)
+
+#define CSID_RDI_CFG1(rdi)		(0x510 + 0x100 * (rdi))
+#define		RDI_CFG1_DROP_H_EN		BIT(5)
+#define		RDI_CFG1_DROP_V_EN		BIT(6)
+#define		RDI_CFG1_CROP_H_EN		BIT(7)
+#define		RDI_CFG1_CROP_V_EN		BIT(8)
+#define		RDI_CFG1_PIX_STORE		BIT(10)
+#define		RDI_CFG1_PACKING_FORMAT_MIPI	BIT(15)
+
+#define CSID_RDI_IRQ_SUBSAMPLE_PATTERN(rdi)	(0x548 + 0x100 * (rdi))
+#define CSID_RDI_IRQ_SUBSAMPLE_PERIOD(rdi)	(0x54C + 0x100 * (rdi))
+
+#define CSI2_RX_CFG0_PHY_SEL_BASE_IDX	1
+
+static void __csid_configure_rx(struct csid_device *csid,
+				struct csid_phy_config *phy, int vc)
+{
+	int val;
+
+	val = (phy->lane_cnt - 1) << CSI2_RX_CFG0_NUM_ACTIVE_LANES;
+	val |= phy->lane_assign << CSI2_RX_CFG0_DL0_INPUT_SEL;
+	val |= (phy->csiphy_id + CSI2_RX_CFG0_PHY_SEL_BASE_IDX) << CSI2_RX_CFG0_PHY_NUM_SEL;
+
+	writel(val, csid->base + CSID_CSI2_RX_CFG0);
+
+	val = CSI2_RX_CFG1_ECC_CORRECTION_EN;
+	if (vc > 3)
+		val |= CSI2_RX_CFG1_VC_MODE;
+
+	writel(val, csid->base + CSID_CSI2_RX_CFG1);
+}
+
+static void __csid_ctrl_rdi(struct csid_device *csid, int enable, u8 rdi)
+{
+	int val = 0;
+
+	if (enable)
+		val = RDI_CTRL_START_CMD;
+
+	writel(val, csid->base + CSID_RDI_CTRL(rdi));
+}
+
+static void __csid_configure_wrapper(struct csid_device *csid)
+{
+	u32 val;
+
+	/* csid lite doesn't need to configure top register */
+	if (csid->res->is_lite)
+		return;
+
+	val = OUTPUT_IFE_EN | INTERNAL_CSID;
+	writel(val, csid->camss->csid_wrapper_base + CSID_IO_PATH_CFG0(csid->id));
+}
+
+static void __csid_configure_rdi_stream(struct csid_device *csid, u8 enable, u8 vc)
+{
+	u32 val;
+	u8 lane_cnt = csid->phy.lane_cnt;
+	/* Source pads matching RDI channels on hardware. Pad 1 -> RDI0, Pad 2 -> RDI1, etc. */
+	struct v4l2_mbus_framefmt *input_format = &csid->fmt[MSM_CSID_PAD_FIRST_SRC + vc];
+	const struct csid_format_info *format = csid_get_fmt_entry(csid->res->formats->formats,
+								   csid->res->formats->nformats,
+								   input_format->code);
+
+	if (!lane_cnt)
+		lane_cnt = 4;
+
+	/*
+	 * DT_ID is a two bit bitfield that is concatenated with
+	 * the four least significant bits of the five bit VC
+	 * bitfield to generate an internal CID value.
+	 *
+	 * CSID_RDI_CFG0(vc)
+	 * DT_ID : 28:27
+	 * VC    : 26:22
+	 * DT    : 21:16
+	 *
+	 * CID   : VC 3:0 << 2 | DT_ID 1:0
+	 */
+	u8 dt_id = vc & 0x03;
+
+	val = RDI_CFG0_TIMESTAMP_EN;
+	val |= RDI_CFG0_TIMESTAMP_STB_SEL;
+	/* note: for non-RDI path, this should be format->decode_format */
+	val |= DECODE_FORMAT_PAYLOAD_ONLY << RDI_CFG0_DECODE_FORMAT;
+	val |= vc << RDI_CFG0_VC;
+	val |= format->data_type << RDI_CFG0_DT;
+	val |= dt_id << RDI_CFG0_DT_ID;
+
+	writel(val, csid->base + CSID_RDI_CFG0(vc));
+
+	val = RDI_CFG1_PACKING_FORMAT_MIPI;
+	val |= RDI_CFG1_PIX_STORE;
+	val |= RDI_CFG1_DROP_H_EN;
+	val |= RDI_CFG1_DROP_V_EN;
+	val |= RDI_CFG1_CROP_H_EN;
+	val |= RDI_CFG1_CROP_V_EN;
+
+	writel(val, csid->base + CSID_RDI_CFG1(vc));
+
+	val = 0;
+	writel(val, csid->base + CSID_RDI_IRQ_SUBSAMPLE_PERIOD(vc));
+
+	val = 1;
+	writel(val, csid->base + CSID_RDI_IRQ_SUBSAMPLE_PATTERN(vc));
+
+	val = 0;
+	writel(val, csid->base + CSID_RDI_CTRL(vc));
+
+	val = readl(csid->base + CSID_RDI_CFG0(vc));
+
+	if (enable)
+		val |= RDI_CFG0_EN;
+	writel(val, csid->base + CSID_RDI_CFG0(vc));
+}
+
+static void csid_configure_stream(struct csid_device *csid, u8 enable)
+{
+	u8 i;
+
+	__csid_configure_wrapper(csid);
+
+	/* Loop through all enabled VCs and configure stream for each */
+	for (i = 0; i < MSM_CSID_MAX_SRC_STREAMS; i++)
+		if (csid->phy.en_vc & BIT(i)) {
+			__csid_configure_rdi_stream(csid, enable, i);
+			__csid_configure_rx(csid, &csid->phy, i);
+			__csid_ctrl_rdi(csid, enable, i);
+		}
+}
+
+static int csid_configure_testgen_pattern(struct csid_device *csid, s32 val)
+{
+	return 0;
+}
+
+static void csid_subdev_reg_update(struct csid_device *csid, int port_id, bool clear)
+{
+	if (clear) {
+		csid->reg_update &= ~CSID_RUP_AUP_RDI(port_id);
+	} else {
+		csid->reg_update |= CSID_RUP_AUP_RDI(port_id);
+		writel(csid->reg_update, csid->base + CSID_RUP_AUP_CMD);
+	}
+}
+
+/*
+ * csid_isr - CSID module interrupt service routine
+ * @irq: Interrupt line
+ * @dev: CSID device
+ *
+ * Return IRQ_HANDLED on success
+ */
+static irqreturn_t csid_isr(int irq, void *dev)
+{
+	struct csid_device *csid = dev;
+	u32 val, buf_done_val;
+	u8 reset_done;
+	int i;
+
+	val = readl(csid->base + CSID_TOP_IRQ_STATUS);
+	writel(val, csid->base + CSID_TOP_IRQ_CLEAR);
+	reset_done = val & TOP_IRQ_STATUS_RESET_DONE;
+
+	val = readl(csid->base + CSID_CSI2_RX_IRQ_STATUS);
+	writel(val, csid->base + CSID_CSI2_RX_IRQ_CLEAR);
+
+	buf_done_val = readl(csid->base + CSID_BUF_DONE_IRQ_STATUS);
+	writel(buf_done_val, csid->base + CSID_BUF_DONE_IRQ_CLEAR);
+
+	/* Read and clear IRQ status for each enabled RDI channel */
+	for (i = 0; i < MSM_CSID_MAX_SRC_STREAMS; i++)
+		if (csid->phy.en_vc & BIT(i)) {
+			val = readl(csid->base + CSID_CSI2_RDIN_IRQ_STATUS(i));
+			writel(val, csid->base + CSID_CSI2_RDIN_IRQ_CLEAR(i));
+
+			if (val & RUP_DONE_IRQ_STATUS)
+				/* clear the reg update bit */
+				csid_subdev_reg_update(csid, i, true);
+
+			if (buf_done_val & BIT(BUF_DONE_IRQ_STATUS_RDI_OFFSET + i)) {
+				/*
+				 * For Titan 780, bus done and RUP IRQ have been moved to
+				 * CSID from VFE. Once CSID received bus done, need notify
+				 * VFE of this event. Trigger VFE to handle bus done process.
+				 */
+				camss_buf_done(csid->camss, csid->id, i);
+			}
+		}
+
+	val = IRQ_CMD_CLEAR;
+	writel(val, csid->base + CSID_IRQ_CMD);
+
+	if (reset_done)
+		complete(&csid->reset_complete);
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * csid_reset - Trigger reset on CSID module and wait to complete
+ * @csid: CSID device
+ *
+ * Return 0 on success or a negative error code otherwise
+ */
+static int csid_reset(struct csid_device *csid)
+{
+	unsigned long time;
+	u32 val;
+	int i;
+
+	reinit_completion(&csid->reset_complete);
+
+	writel(1, csid->base + CSID_TOP_IRQ_CLEAR);
+	writel(1, csid->base + CSID_IRQ_CMD);
+	writel(1, csid->base + CSID_TOP_IRQ_MASK);
+
+	for (i = 0; i < MSM_CSID_MAX_SRC_STREAMS; i++)
+		if (csid->phy.en_vc & BIT(i)) {
+			writel(BIT(BUF_DONE_IRQ_STATUS_RDI_OFFSET + i),
+			       csid->base + CSID_BUF_DONE_IRQ_CLEAR);
+			writel(IRQ_CMD_CLEAR, csid->base + CSID_IRQ_CMD);
+			writel(BIT(BUF_DONE_IRQ_STATUS_RDI_OFFSET + i),
+			       csid->base + CSID_BUF_DONE_IRQ_MASK);
+		}
+
+	/* preserve registers */
+	val = RST_LOCATION | RST_MODE;
+	writel(val, csid->base + CSID_RST_CFG);
+
+	val = SELECT_HW_RST | SELECT_IRQ_RST;
+	writel(val, csid->base + CSID_RST_CMD);
+
+	time = wait_for_completion_timeout(&csid->reset_complete,
+					   msecs_to_jiffies(CSID_RESET_TIMEOUT_MS));
+	if (!time) {
+		dev_err(csid->camss->dev, "CSID reset timeout\n");
+		return -EIO;
+	}
+
+	return 0;
+}
+
+static void csid_subdev_init(struct csid_device *csid)
+{
+	csid->testgen.nmodes = CSID_PAYLOAD_MODE_DISABLED;
+}
+
+const struct csid_hw_ops csid_ops_780 = {
+	.configure_stream = csid_configure_stream,
+	.configure_testgen_pattern = csid_configure_testgen_pattern,
+	.hw_version = csid_hw_version,
+	.isr = csid_isr,
+	.reset = csid_reset,
+	.src_pad_code = csid_src_pad_code,
+	.subdev_init = csid_subdev_init,
+	.reg_update = csid_subdev_reg_update,
+};
diff --git a/drivers/media/platform/qcom/camss/camss-csid-780.h b/drivers/media/platform/qcom/camss/camss-csid-780.h
new file mode 100644
index 000000000000..b78923bd892d
--- /dev/null
+++ b/drivers/media/platform/qcom/camss/camss-csid-780.h
@@ -0,0 +1,25 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * camss-csid-780.h
+ *
+ * Qualcomm MSM Camera Subsystem - CSID (CSI Decoder) Module Generation 3
+ *
+ * Copyright (c) 2024-2025 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+#ifndef __QC_MSM_CAMSS_CSID_780_H__
+#define __QC_MSM_CAMSS_CSID_780_H__
+
+#define DECODE_FORMAT_UNCOMPRESSED_8_BIT	0x1
+#define DECODE_FORMAT_UNCOMPRESSED_10_BIT	0x2
+#define DECODE_FORMAT_UNCOMPRESSED_12_BIT	0x3
+#define DECODE_FORMAT_UNCOMPRESSED_14_BIT	0x4
+#define DECODE_FORMAT_UNCOMPRESSED_16_BIT	0x5
+#define DECODE_FORMAT_UNCOMPRESSED_20_BIT	0x6
+#define DECODE_FORMAT_UNCOMPRESSED_24_BIT	0x7
+#define DECODE_FORMAT_PAYLOAD_ONLY		0xf
+
+#define PLAIN_FORMAT_PLAIN8	0x0 /* supports DPCM, UNCOMPRESSED_6/8_BIT */
+#define PLAIN_FORMAT_PLAIN16	0x1 /* supports DPCM, UNCOMPRESSED_10/16_BIT */
+#define PLAIN_FORMAT_PLAIN32	0x2 /* supports UNCOMPRESSED_20_BIT */
+
+#endif /* __QC_MSM_CAMSS_CSID_780_H__ */
diff --git a/drivers/media/platform/qcom/camss/camss-csid.h b/drivers/media/platform/qcom/camss/camss-csid.h
index 1369e7ea7219..4776166f3d8f 100644
--- a/drivers/media/platform/qcom/camss/camss-csid.h
+++ b/drivers/media/platform/qcom/camss/camss-csid.h
@@ -237,6 +237,7 @@ extern const struct csid_formats csid_formats_gen2;
 extern const struct csid_hw_ops csid_ops_4_1;
 extern const struct csid_hw_ops csid_ops_4_7;
 extern const struct csid_hw_ops csid_ops_gen2;
+extern const struct csid_hw_ops csid_ops_780;
 
 /*
  * csid_is_lite - Check if CSID is CSID lite.
diff --git a/drivers/media/platform/qcom/camss/camss.c b/drivers/media/platform/qcom/camss/camss.c
index 39f7fa6e9f28..cd845cf42b98 100644
--- a/drivers/media/platform/qcom/camss/camss.c
+++ b/drivers/media/platform/qcom/camss/camss.c
@@ -2045,6 +2045,88 @@ static const struct camss_subdev_resources csiphy_res_8550[] = {
 	}
 };
 
+static const struct resources_wrapper csid_wrapper_res_sm8550 = {
+	.reg = "csid_wrapper",
+};
+
+static const struct camss_subdev_resources csid_res_8550[] = {
+	/* CSID0 */
+	{
+		.regulators = {},
+		.clock = { "csid", "csiphy_rx" },
+		.clock_rate = { { 400000000, 480000000 },
+				{ 400000000, 480000000 } },
+		.reg = { "csid0" },
+		.interrupt = { "csid0" },
+		.csid = {
+			.is_lite = false,
+			.parent_dev_ops = &vfe_parent_dev_ops,
+			.hw_ops = &csid_ops_780,
+			.formats = &csid_formats_gen2
+		}
+	},
+	/* CSID1 */
+	{
+		.regulators = {},
+		.clock = { "csid", "csiphy_rx" },
+		.clock_rate = { { 400000000, 480000000 },
+				{ 400000000, 480000000 } },
+		.reg = { "csid1" },
+		.interrupt = { "csid1" },
+		.csid = {
+			.is_lite = false,
+			.parent_dev_ops = &vfe_parent_dev_ops,
+			.hw_ops = &csid_ops_780,
+			.formats = &csid_formats_gen2
+		}
+	},
+	/* CSID2 */
+	{
+		.regulators = {},
+		.clock = { "csid", "csiphy_rx" },
+		.clock_rate = { { 400000000, 480000000 },
+				{ 400000000, 480000000 } },
+		.reg = { "csid2" },
+		.interrupt = { "csid2" },
+		.csid = {
+			.is_lite = false,
+			.parent_dev_ops = &vfe_parent_dev_ops,
+			.hw_ops = &csid_ops_780,
+			.formats = &csid_formats_gen2
+		}
+	},
+	/* CSID3 */
+	{
+		.regulators = {},
+		.clock = { "vfe_lite_csid", "vfe_lite_cphy_rx" },
+		.clock_rate = { { 400000000, 480000000 },
+				{ 400000000, 480000000 } },
+		.reg = { "csid_lite0" },
+		.interrupt = { "csid_lite0" },
+		.csid = {
+			.is_lite = true,
+			.parent_dev_ops = &vfe_parent_dev_ops,
+			.hw_ops = &csid_ops_780,
+			.formats = &csid_formats_gen2
+		}
+	},
+	/* CSID4 */
+	{
+		.regulators = {},
+		.clock = { "vfe_lite_csid", "vfe_lite_cphy_rx" },
+		.clock_rate = { { 400000000, 480000000 },
+				{ 400000000, 480000000 } },
+		.reg = { "csid_lite1" },
+		.interrupt = { "csid_lite1" },
+		.csid = {
+			.is_lite = true,
+			.parent_dev_ops = &vfe_parent_dev_ops,
+			.hw_ops = &csid_ops_780,
+			.formats = &csid_formats_gen2
+		}
+	}
+};
+
 static const struct resources_icc icc_res_sm8550[] = {
 	{
 		.name = "ahb",
@@ -3149,9 +3231,12 @@ static const struct camss_resources sm8550_resources = {
 	.version = CAMSS_8550,
 	.pd_name = "top",
 	.csiphy_res = csiphy_res_8550,
+	.csid_res = csid_res_8550,
+	.csid_wrapper_res = &csid_wrapper_res_sm8550,
 	.icc_res = icc_res_sm8550,
 	.icc_path_num = ARRAY_SIZE(icc_res_sm8550),
 	.csiphy_num = ARRAY_SIZE(csiphy_res_8550),
+	.csid_num = ARRAY_SIZE(csid_res_8550),
 	.link_entities = camss_link_entities
 };
 
-- 
2.34.1

[PATCH v8 16/16] media: qcom: camss: Add support for VFE 780

[Depeng Shao]

Add support for VFE found on SM8550 (Titan 780). This implementation is
based on the titan 480 implementation. It supports the normal and lite
VFE.

Co-developed-by: Yongsheng Li <quic_yon@quicinc.com>
Signed-off-by: Yongsheng Li <quic_yon@quicinc.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Depeng Shao <quic_depengs@quicinc.com>
---
 drivers/media/platform/qcom/camss/Makefile    |   1 +
 .../media/platform/qcom/camss/camss-vfe-780.c | 159 ++++++++++++++++++
 drivers/media/platform/qcom/camss/camss-vfe.c |   2 +
 drivers/media/platform/qcom/camss/camss-vfe.h |   1 +
 drivers/media/platform/qcom/camss/camss.c     | 121 +++++++++++++
 5 files changed, 284 insertions(+)
 create mode 100644 drivers/media/platform/qcom/camss/camss-vfe-780.c

diff --git a/drivers/media/platform/qcom/camss/Makefile b/drivers/media/platform/qcom/camss/Makefile
index 9a723e8712a2..f6db5b3b5ace 100644
--- a/drivers/media/platform/qcom/camss/Makefile
+++ b/drivers/media/platform/qcom/camss/Makefile
@@ -17,6 +17,7 @@ qcom-camss-objs += \
 		camss-vfe-4-8.o \
 		camss-vfe-17x.o \
 		camss-vfe-480.o \
+		camss-vfe-780.o \
 		camss-vfe-gen1.o \
 		camss-vfe.o \
 		camss-video.o \
diff --git a/drivers/media/platform/qcom/camss/camss-vfe-780.c b/drivers/media/platform/qcom/camss/camss-vfe-780.c
new file mode 100644
index 000000000000..b9812d70f91b
--- /dev/null
+++ b/drivers/media/platform/qcom/camss/camss-vfe-780.c
@@ -0,0 +1,159 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Qualcomm MSM Camera Subsystem - VFE (Video Front End) Module v780 (SM8550)
+ *
+ * Copyright (c) 2024 Qualcomm Technologies, Inc.
+ */
+
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+
+#include "camss.h"
+#include "camss-vfe.h"
+
+#define BUS_REG_BASE			(vfe_is_lite(vfe) ? 0x200 : 0xC00)
+
+#define VFE_BUS_WM_CGC_OVERRIDE		(BUS_REG_BASE + 0x08)
+#define		WM_CGC_OVERRIDE_ALL		(0x7FFFFFF)
+
+#define VFE_BUS_WM_TEST_BUS_CTRL	(BUS_REG_BASE + 0xDC)
+
+#define VFE_BUS_WM_CFG(n)		(BUS_REG_BASE + 0x200 + (n) * 0x100)
+#define		WM_CFG_EN			BIT(0)
+#define		WM_VIR_FRM_EN			BIT(1)
+#define		WM_CFG_MODE			BIT(16)
+#define VFE_BUS_WM_IMAGE_ADDR(n)	(BUS_REG_BASE + 0x204 + (n) * 0x100)
+#define VFE_BUS_WM_FRAME_INCR(n)	(BUS_REG_BASE + 0x208 + (n) * 0x100)
+#define VFE_BUS_WM_IMAGE_CFG_0(n)	(BUS_REG_BASE + 0x20c + (n) * 0x100)
+#define		WM_IMAGE_CFG_0_DEFAULT_WIDTH	(0xFFFF)
+#define VFE_BUS_WM_IMAGE_CFG_2(n)	(BUS_REG_BASE + 0x214 + (n) * 0x100)
+#define		WM_IMAGE_CFG_2_DEFAULT_STRIDE	(0xFFFF)
+#define VFE_BUS_WM_PACKER_CFG(n)	(BUS_REG_BASE + 0x218 + (n) * 0x100)
+
+#define VFE_BUS_WM_IRQ_SUBSAMPLE_PERIOD(n)	(BUS_REG_BASE + 0x230 + (n) * 0x100)
+#define VFE_BUS_WM_IRQ_SUBSAMPLE_PATTERN(n)	(BUS_REG_BASE + 0x234 + (n) * 0x100)
+#define VFE_BUS_WM_FRAMEDROP_PERIOD(n)		(BUS_REG_BASE + 0x238 + (n) * 0x100)
+#define VFE_BUS_WM_FRAMEDROP_PATTERN(n)		(BUS_REG_BASE + 0x23c + (n) * 0x100)
+
+#define VFE_BUS_WM_MMU_PREFETCH_CFG(n)		(BUS_REG_BASE + 0x260 + (n) * 0x100)
+#define VFE_BUS_WM_MMU_PREFETCH_MAX_OFFSET(n)	(BUS_REG_BASE + 0x264 + (n) * 0x100)
+
+/*
+ * Bus client mapping:
+ *
+ * Full VFE:
+ * 23 = RDI0, 24 = RDI1, 25 = RDI2
+ *
+ * VFE LITE:
+ * 0 = RDI0, 1 = RDI1, 2 = RDI3, 4 = RDI4
+ */
+#define RDI_WM(n)			((vfe_is_lite(vfe) ? 0x0 : 0x17) + (n))
+
+static void vfe_wm_start(struct vfe_device *vfe, u8 wm, struct vfe_line *line)
+{
+	struct v4l2_pix_format_mplane *pix =
+		&line->video_out.active_fmt.fmt.pix_mp;
+
+	wm = RDI_WM(wm);
+
+	/* no clock gating at bus input */
+	writel(WM_CGC_OVERRIDE_ALL, vfe->base + VFE_BUS_WM_CGC_OVERRIDE);
+
+	writel(0x0, vfe->base + VFE_BUS_WM_TEST_BUS_CTRL);
+
+	writel(ALIGN(pix->plane_fmt[0].bytesperline, 16) * pix->height >> 8,
+	       vfe->base + VFE_BUS_WM_FRAME_INCR(wm));
+	writel((WM_IMAGE_CFG_0_DEFAULT_WIDTH & 0xFFFF),
+	       vfe->base + VFE_BUS_WM_IMAGE_CFG_0(wm));
+	writel(WM_IMAGE_CFG_2_DEFAULT_STRIDE,
+	       vfe->base + VFE_BUS_WM_IMAGE_CFG_2(wm));
+	writel(0, vfe->base + VFE_BUS_WM_PACKER_CFG(wm));
+
+	/* no dropped frames, one irq per frame */
+	writel(0, vfe->base + VFE_BUS_WM_FRAMEDROP_PERIOD(wm));
+	writel(1, vfe->base + VFE_BUS_WM_FRAMEDROP_PATTERN(wm));
+	writel(0, vfe->base + VFE_BUS_WM_IRQ_SUBSAMPLE_PERIOD(wm));
+	writel(1, vfe->base + VFE_BUS_WM_IRQ_SUBSAMPLE_PATTERN(wm));
+
+	writel(1, vfe->base + VFE_BUS_WM_MMU_PREFETCH_CFG(wm));
+	writel(0xFFFFFFFF, vfe->base + VFE_BUS_WM_MMU_PREFETCH_MAX_OFFSET(wm));
+
+	writel(WM_CFG_EN | WM_CFG_MODE, vfe->base + VFE_BUS_WM_CFG(wm));
+}
+
+static void vfe_wm_stop(struct vfe_device *vfe, u8 wm)
+{
+	wm = RDI_WM(wm);
+	writel(0, vfe->base + VFE_BUS_WM_CFG(wm));
+}
+
+static void vfe_wm_update(struct vfe_device *vfe, u8 wm, u32 addr,
+			  struct vfe_line *line)
+{
+	wm = RDI_WM(wm);
+	writel((addr >> 8) & 0xFFFFFFFF, vfe->base + VFE_BUS_WM_IMAGE_ADDR(wm));
+
+	dev_dbg(vfe->camss->dev, "wm:%d, image buf addr:0x%x\n",
+		wm, addr);
+}
+
+static void vfe_reg_update(struct vfe_device *vfe, enum vfe_line_id line_id)
+{
+	int port_id = line_id;
+
+	camss_reg_update(vfe->camss, vfe->id, port_id, false);
+}
+
+static inline void vfe_reg_update_clear(struct vfe_device *vfe,
+					enum vfe_line_id line_id)
+{
+	int port_id = line_id;
+
+	camss_reg_update(vfe->camss, vfe->id, port_id, true);
+}
+
+static const struct camss_video_ops vfe_video_ops_780 = {
+	.queue_buffer = vfe_queue_buffer_v2,
+	.flush_buffers = vfe_flush_buffers,
+};
+
+static void vfe_subdev_init(struct device *dev, struct vfe_device *vfe)
+{
+	vfe->video_ops = vfe_video_ops_780;
+}
+
+static void vfe_global_reset(struct vfe_device *vfe)
+{
+	vfe_isr_reset_ack(vfe);
+}
+
+static irqreturn_t vfe_isr(int irq, void *dev)
+{
+	/* nop */
+	return IRQ_HANDLED;
+}
+
+static int vfe_halt(struct vfe_device *vfe)
+{
+	/* rely on vfe_disable_output() to stop the VFE */
+	return 0;
+}
+
+const struct vfe_hw_ops vfe_ops_780 = {
+	.global_reset = vfe_global_reset,
+	.hw_version = vfe_hw_version,
+	.isr = vfe_isr,
+	.pm_domain_off = vfe_pm_domain_off,
+	.pm_domain_on = vfe_pm_domain_on,
+	.reg_update = vfe_reg_update,
+	.reg_update_clear = vfe_reg_update_clear,
+	.subdev_init = vfe_subdev_init,
+	.vfe_disable = vfe_disable,
+	.vfe_enable = vfe_enable_v2,
+	.vfe_halt = vfe_halt,
+	.vfe_wm_start = vfe_wm_start,
+	.vfe_wm_stop = vfe_wm_stop,
+	.vfe_buf_done = vfe_buf_done,
+	.vfe_wm_update = vfe_wm_update,
+};
diff --git a/drivers/media/platform/qcom/camss/camss-vfe.c b/drivers/media/platform/qcom/camss/camss-vfe.c
index 2a037860b09f..9ffa6bc72cf1 100644
--- a/drivers/media/platform/qcom/camss/camss-vfe.c
+++ b/drivers/media/platform/qcom/camss/camss-vfe.c
@@ -345,6 +345,7 @@ static u32 vfe_src_pad_code(struct vfe_line *line, u32 sink_code,
 	case CAMSS_8250:
 	case CAMSS_8280XP:
 	case CAMSS_845:
+	case CAMSS_8550:
 		switch (sink_code) {
 		case MEDIA_BUS_FMT_YUYV8_1X16:
 		{
@@ -1970,6 +1971,7 @@ static int vfe_bpl_align(struct vfe_device *vfe)
 	case CAMSS_8250:
 	case CAMSS_8280XP:
 	case CAMSS_845:
+	case CAMSS_8550:
 		ret = 16;
 		break;
 	default:
diff --git a/drivers/media/platform/qcom/camss/camss-vfe.h b/drivers/media/platform/qcom/camss/camss-vfe.h
index fcbf4f609129..9dec5bc0d1b1 100644
--- a/drivers/media/platform/qcom/camss/camss-vfe.h
+++ b/drivers/media/platform/qcom/camss/camss-vfe.h
@@ -243,6 +243,7 @@ extern const struct vfe_hw_ops vfe_ops_4_7;
 extern const struct vfe_hw_ops vfe_ops_4_8;
 extern const struct vfe_hw_ops vfe_ops_170;
 extern const struct vfe_hw_ops vfe_ops_480;
+extern const struct vfe_hw_ops vfe_ops_780;
 
 int vfe_get(struct vfe_device *vfe);
 void vfe_put(struct vfe_device *vfe);
diff --git a/drivers/media/platform/qcom/camss/camss.c b/drivers/media/platform/qcom/camss/camss.c
index cd845cf42b98..ccc73f51d842 100644
--- a/drivers/media/platform/qcom/camss/camss.c
+++ b/drivers/media/platform/qcom/camss/camss.c
@@ -2127,6 +2127,125 @@ static const struct camss_subdev_resources csid_res_8550[] = {
 	}
 };
 
+static const struct camss_subdev_resources vfe_res_8550[] = {
+	/* VFE0 */
+	{
+		.regulators = {},
+		.clock = { "gcc_axi_hf", "cpas_ahb", "cpas_fast_ahb_clk", "vfe0_fast_ahb",
+			   "vfe0", "cpas_vfe0", "camnoc_axi" },
+		.clock_rate = { { 0 },
+				{ 80000000 },
+				{ 300000000, 400000000 },
+				{ 300000000, 400000000 },
+				{ 466000000, 594000000, 675000000, 785000000 },
+				{ 300000000, 400000000 },
+				{ 300000000, 400000000 } },
+		.reg = { "vfe0" },
+		.interrupt = { "vfe0" },
+		.vfe = {
+			.line_num = 3,
+			.is_lite = false,
+			.has_pd = true,
+			.pd_name = "ife0",
+			.hw_ops = &vfe_ops_780,
+			.formats_rdi = &vfe_formats_rdi_845,
+			.formats_pix = &vfe_formats_pix_845
+		}
+	},
+	/* VFE1 */
+	{
+		.regulators = {},
+		.clock = { "gcc_axi_hf", "cpas_ahb", "cpas_fast_ahb_clk", "vfe1_fast_ahb",
+			   "vfe1", "cpas_vfe1", "camnoc_axi" },
+		.clock_rate = {	{ 0 },
+				{ 80000000 },
+				{ 300000000, 400000000 },
+				{ 300000000, 400000000 },
+				{ 466000000, 594000000, 675000000, 785000000 },
+				{ 300000000, 400000000 },
+				{ 300000000, 400000000 } },
+		.reg = { "vfe1" },
+		.interrupt = { "vfe1" },
+		.vfe = {
+			.line_num = 3,
+			.is_lite = false,
+			.has_pd = true,
+			.pd_name = "ife1",
+			.hw_ops = &vfe_ops_780,
+			.formats_rdi = &vfe_formats_rdi_845,
+			.formats_pix = &vfe_formats_pix_845
+		}
+	},
+	/* VFE2 */
+	{
+		.regulators = {},
+		.clock = { "gcc_axi_hf", "cpas_ahb", "cpas_fast_ahb_clk", "vfe2_fast_ahb",
+			   "vfe2", "cpas_vfe2", "camnoc_axi" },
+		.clock_rate = {	{ 0 },
+				{ 80000000 },
+				{ 300000000, 400000000 },
+				{ 300000000, 400000000 },
+				{ 466000000, 594000000, 675000000, 785000000 },
+				{ 300000000, 400000000 },
+				{ 300000000, 400000000 } },
+		.reg = { "vfe2" },
+		.interrupt = { "vfe2" },
+		.vfe = {
+			.line_num = 3,
+			.is_lite = false,
+			.has_pd = true,
+			.pd_name = "ife2",
+			.hw_ops = &vfe_ops_780,
+			.formats_rdi = &vfe_formats_rdi_845,
+			.formats_pix = &vfe_formats_pix_845
+		}
+	},
+	/* VFE3 lite */
+	{
+		.regulators = {},
+		.clock = { "gcc_axi_hf", "cpas_ahb", "cpas_fast_ahb_clk", "vfe_lite_ahb",
+			   "vfe_lite", "cpas_ife_lite", "camnoc_axi" },
+		.clock_rate = {	{ 0 },
+				{ 80000000 },
+				{ 300000000, 400000000 },
+				{ 300000000, 400000000 },
+				{ 400000000, 480000000 },
+				{ 300000000, 400000000 },
+				{ 300000000, 400000000 } },
+		.reg = { "vfe_lite0" },
+		.interrupt = { "vfe_lite0" },
+		.vfe = {
+			.line_num = 4,
+			.is_lite = true,
+			.hw_ops = &vfe_ops_780,
+			.formats_rdi = &vfe_formats_rdi_845,
+			.formats_pix = &vfe_formats_pix_845
+		}
+	},
+	/* VFE4 lite */
+	{
+		.regulators = {},
+		.clock = { "gcc_axi_hf", "cpas_ahb", "cpas_fast_ahb_clk", "vfe_lite_ahb",
+			   "vfe_lite", "cpas_ife_lite", "camnoc_axi" },
+		.clock_rate = {	{ 0 },
+				{ 80000000 },
+				{ 300000000, 400000000 },
+				{ 300000000, 400000000 },
+				{ 400000000, 480000000 },
+				{ 300000000, 400000000 },
+				{ 300000000, 400000000 } },
+		.reg = { "vfe_lite1" },
+		.interrupt = { "vfe_lite1" },
+		.vfe = {
+			.line_num = 4,
+			.is_lite = true,
+			.hw_ops = &vfe_ops_780,
+			.formats_rdi = &vfe_formats_rdi_845,
+			.formats_pix = &vfe_formats_pix_845
+		}
+	},
+};
+
 static const struct resources_icc icc_res_sm8550[] = {
 	{
 		.name = "ahb",
@@ -3232,11 +3351,13 @@ static const struct camss_resources sm8550_resources = {
 	.pd_name = "top",
 	.csiphy_res = csiphy_res_8550,
 	.csid_res = csid_res_8550,
+	.vfe_res = vfe_res_8550,
 	.csid_wrapper_res = &csid_wrapper_res_sm8550,
 	.icc_res = icc_res_sm8550,
 	.icc_path_num = ARRAY_SIZE(icc_res_sm8550),
 	.csiphy_num = ARRAY_SIZE(csiphy_res_8550),
 	.csid_num = ARRAY_SIZE(csid_res_8550),
+	.vfe_num = ARRAY_SIZE(vfe_res_8550),
 	.link_entities = camss_link_entities
 };
 
-- 
2.34.1

Re: [PATCH v8 00/16] media: qcom: camss: Add sm8550 support

[Bryan O'Donoghue]

On 08/01/2025 14:37, Depeng Shao wrote:
> v8:
> - Add correct version number for each patch - Krzysztof, Hans, Bryan
> - Correct the copyright in patches [15/16] and [16/16]
> - Link to v7: https://lore.kernel.org/all/20241225133523.4034820-1-quic_depengs@quicinc.com/
Patch #9 doesn't apply to media.git/next

git remote add media git://linuxtv.org/media.git
git fetch media

git checkout -b media-next-25-10-01-camss-8550 media/next

b4 shazam 20250108143733.2761200-1-quic_depengs@quicinc.com 

Grabbing thread from 
lore.kernel.org/all/20250108143733.2761200-1-quic_depengs@quicinc.com/t.mbox.gz
Checking for newer revisions
Grabbing search results from lore.kernel.org
Analyzing 17 messages in the thread
Analyzing 260 code-review messages
Checking attestation on all messages, may take a moment...
---
   ✓ [PATCH v8 1/16] media: qcom: camss: csiphy-3ph: Fix trivial 
indentation fault in defines
   ✓ [PATCH v8 2/16] media: qcom: camss: csiphy-3ph: Remove redundant 
PHY init sequence control loop
   ✓ [PATCH v8 3/16] media: qcom: camss: csiphy-3ph: Rename struct
   ✓ [PATCH v8 4/16] media: qcom: camss: csiphy: Add an init callback to 
CSI PHY devices
   ✓ [PATCH v8 5/16] media: qcom: camss: csiphy-3ph: Move CSIPHY 
variables to data field inside csiphy struct
   ✓ [PATCH v8 6/16] media: qcom: camss: csiphy-3ph: Use an offset 
variable to find common control regs
   ✓ [PATCH v8 7/16] media: qcom: camss: csid: Move common code into 
csid core
   ✓ [PATCH v8 8/16] media: qcom: camss: vfe: Move common code into vfe core
   ✓ [PATCH v8 9/16] media: qcom: camss: Add callback API for RUP update 
and buf done
   ✓ [PATCH v8 10/16] media: qcom: camss: Add default case in 
vfe_src_pad_code
   ✓ [PATCH v8 11/16] media: qcom: camss: csid: Only add TPG v4l2 ctrl 
if TPG hardware is available
   ✓ [PATCH v8 12/16] dt-bindings: media: camss: Add qcom,sm8550-camss 
binding
   ✓ [PATCH v8 13/16] media: qcom: camss: Add sm8550 compatible
   ✓ [PATCH v8 14/16] media: qcom: camss: csiphy-3ph: Add Gen2 v2.1.2 
two-phase MIPI CSI-2 DPHY support
   ✓ [PATCH v8 15/16] media: qcom: camss: Add CSID 780 support
   ✓ [PATCH v8 16/16] media: qcom: camss: Add support for VFE 780
   ---
   ✓ Signed: DKIM/quicinc.com
---
Total patches: 16
---
  Base: using specified base-commit 8155b4ef3466f0e289e8fcc9e6e62f3f4dceeac2
Applying: media: qcom: camss: csiphy-3ph: Fix trivial indentation fault 
in defines
Applying: media: qcom: camss: csiphy-3ph: Remove redundant PHY init 
sequence control loop
Applying: media: qcom: camss: csiphy-3ph: Rename struct
Applying: media: qcom: camss: csiphy: Add an init callback to CSI PHY 
devices
Applying: media: qcom: camss: csiphy-3ph: Move CSIPHY variables to data 
field inside csiphy struct
Applying: media: qcom: camss: csiphy-3ph: Use an offset variable to find 
common control regs
Applying: media: qcom: camss: csid: Move common code into csid core
Applying: media: qcom: camss: vfe: Move common code into vfe core
Applying: media: qcom: camss: Add callback API for RUP update and buf done
Patch failed at 0009 media: qcom: camss: Add callback API for RUP update 
and buf done
error: patch failed: drivers/media/platform/qcom/camss/camss.c:2454

Re: [PATCH v8 00/16] media: qcom: camss: Add sm8550 support

[Depeng Shao]

Hi Bryan,

On 1/10/2025 9:50 PM, Bryan O'Donoghue wrote:
> On 08/01/2025 14:37, Depeng Shao wrote:
>> v8:
>> - Add correct version number for each patch - Krzysztof, Hans, Bryan
>> - Correct the copyright in patches [15/16] and [16/16]
>> - Link to v7: https://lore.kernel.org/all/20241225133523.4034820-1- 
>> quic_depengs@quicinc.com/
> Patch #9 doesn't apply to media.git/next
> 

Yes, below patch[1] is merged these days, so my series get conflict. I 
will rebase my series and verify it next Monday.

[1] Revert "media: qcom: camss: Restructure camss_link_entities"

> git remote add media git://linuxtv.org/media.git
> git fetch media
> 
> git checkout -b media-next-25-10-01-camss-8550 media/next
> 
> b4 shazam 20250108143733.2761200-1-quic_depengs@quicinc.com
> Grabbing thread from lore.kernel.org/all/20250108143733.2761200-1- 
> quic_depengs@quicinc.com/t.mbox.gz
> Checking for newer revisions
> Grabbing search results from lore.kernel.org
> Analyzing 17 messages in the thread
> Analyzing 260 code-review messages
> Checking attestation on all messages, may take a moment...
> ---
>    ✓ [PATCH v8 1/16] media: qcom: camss: csiphy-3ph: Fix trivial 
> indentation fault in defines
>    ✓ [PATCH v8 2/16] media: qcom: camss: csiphy-3ph: Remove redundant 
> PHY init sequence control loop
>    ✓ [PATCH v8 3/16] media: qcom: camss: csiphy-3ph: Rename struct
>    ✓ [PATCH v8 4/16] media: qcom: camss: csiphy: Add an init callback to 
> CSI PHY devices
>    ✓ [PATCH v8 5/16] media: qcom: camss: csiphy-3ph: Move CSIPHY 
> variables to data field inside csiphy struct
>    ✓ [PATCH v8 6/16] media: qcom: camss: csiphy-3ph: Use an offset 
> variable to find common control regs
>    ✓ [PATCH v8 7/16] media: qcom: camss: csid: Move common code into 
> csid core
>    ✓ [PATCH v8 8/16] media: qcom: camss: vfe: Move common code into vfe 
> core
>    ✓ [PATCH v8 9/16] media: qcom: camss: Add callback API for RUP update 
> and buf done
>    ✓ [PATCH v8 10/16] media: qcom: camss: Add default case in 
> vfe_src_pad_code
>    ✓ [PATCH v8 11/16] media: qcom: camss: csid: Only add TPG v4l2 ctrl 
> if TPG hardware is available
>    ✓ [PATCH v8 12/16] dt-bindings: media: camss: Add qcom,sm8550-camss 
> binding
>    ✓ [PATCH v8 13/16] media: qcom: camss: Add sm8550 compatible
>    ✓ [PATCH v8 14/16] media: qcom: camss: csiphy-3ph: Add Gen2 v2.1.2 
> two-phase MIPI CSI-2 DPHY support
>    ✓ [PATCH v8 15/16] media: qcom: camss: Add CSID 780 support
>    ✓ [PATCH v8 16/16] media: qcom: camss: Add support for VFE 780
>    ---
>    ✓ Signed: DKIM/quicinc.com
> ---
> Total patches: 16
> ---
>   Base: using specified base-commit 
> 8155b4ef3466f0e289e8fcc9e6e62f3f4dceeac2
> Applying: media: qcom: camss: csiphy-3ph: Fix trivial indentation fault 
> in defines
> Applying: media: qcom: camss: csiphy-3ph: Remove redundant PHY init 
> sequence control loop
> Applying: media: qcom: camss: csiphy-3ph: Rename struct
> Applying: media: qcom: camss: csiphy: Add an init callback to CSI PHY 
> devices
> Applying: media: qcom: camss: csiphy-3ph: Move CSIPHY variables to data 
> field inside csiphy struct
> Applying: media: qcom: camss: csiphy-3ph: Use an offset variable to find 
> common control regs
> Applying: media: qcom: camss: csid: Move common code into csid core
> Applying: media: qcom: camss: vfe: Move common code into vfe core
> Applying: media: qcom: camss: Add callback API for RUP update and buf done
> Patch failed at 0009 media: qcom: camss: Add callback API for RUP update 
> and buf done
> error: patch failed: drivers/media/platform/qcom/camss/camss.c:2454
> 

Thanks,
Depeng

Re: [PATCH v8 12/16] dt-bindings: media: camss: Add qcom,sm8550-camss binding

[Krzysztof Kozlowski]

On Wed, Jan 08, 2025 at 08:07:29PM +0530, Depeng Shao wrote:
> Add bindings for qcom,sm8550-camss in order to support the camera
> subsystem for sm8550.
> 
> Co-developed-by: Yongsheng Li <quic_yon@quicinc.com>
> Signed-off-by: Yongsheng Li <quic_yon@quicinc.com>
> Signed-off-by: Depeng Shao <quic_depengs@quicinc.com>
> ---
>  .../bindings/media/qcom,sm8550-camss.yaml     | 597 ++++++++++++++++++
>  1 file changed, 597 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/qcom,sm8550-camss.yaml

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

Re: [PATCH v8 11/16] media: qcom: camss: csid: Only add TPG v4l2 ctrl if TPG hardware is available

[Bryan O'Donoghue]

On 08/01/2025 14:37, Depeng Shao wrote:
> There is no CSID TPG on some SoCs, so the v4l2 ctrl in CSID driver
> shouldn't be registered. Checking the supported TPG modes to indicate
> if the TPG hardware exists or not and only registering v4l2 ctrl for
> CSID only when the TPG hardware is present.
> 
> Signed-off-by: Depeng Shao <quic_depengs@quicinc.com>
> ---
>   .../media/platform/qcom/camss/camss-csid.c    | 60 +++++++++++--------
>   1 file changed, 35 insertions(+), 25 deletions(-)
> 
> diff --git a/drivers/media/platform/qcom/camss/camss-csid.c b/drivers/media/platform/qcom/camss/camss-csid.c
> index 6cf8e434dc05..e26a69a454a7 100644
> --- a/drivers/media/platform/qcom/camss/camss-csid.c
> +++ b/drivers/media/platform/qcom/camss/camss-csid.c
> @@ -760,11 +760,13 @@ static int csid_set_stream(struct v4l2_subdev *sd, int enable)
>   	int ret;
>   
>   	if (enable) {
> -		ret = v4l2_ctrl_handler_setup(&csid->ctrls);
> -		if (ret < 0) {
> -			dev_err(csid->camss->dev,
> -				"could not sync v4l2 controls: %d\n", ret);
> -			return ret;
> +		if (csid->testgen.nmodes != CSID_PAYLOAD_MODE_DISABLED) {
> +			ret = v4l2_ctrl_handler_setup(&csid->ctrls);
> +			if (ret < 0) {
> +				dev_err(csid->camss->dev,
> +					"could not sync v4l2 controls: %d\n", ret);
> +				return ret;
> +			}
>   		}
>   
>   		if (!csid->testgen.enabled &&
> @@ -838,7 +840,8 @@ static void csid_try_format(struct csid_device *csid,
>   		break;
>   
>   	case MSM_CSID_PAD_SRC:
> -		if (csid->testgen_mode->cur.val == 0) {
> +		if (csid->testgen.nmodes == CSID_PAYLOAD_MODE_DISABLED ||
> +		    csid->testgen_mode->cur.val == 0) {
>   			/* Test generator is disabled, */
>   			/* keep pad formats in sync */
>   			u32 code = fmt->code;
> @@ -888,7 +891,8 @@ static int csid_enum_mbus_code(struct v4l2_subdev *sd,
>   
>   		code->code = csid->res->formats->formats[code->index].code;
>   	} else {
> -		if (csid->testgen_mode->cur.val == 0) {
> +		if (csid->testgen.nmodes == CSID_PAYLOAD_MODE_DISABLED ||
> +		    csid->testgen_mode->cur.val == 0) {
>   			struct v4l2_mbus_framefmt *sink_fmt;
>   
>   			sink_fmt = __csid_get_format(csid, sd_state,
> @@ -1267,7 +1271,8 @@ static int csid_link_setup(struct media_entity *entity,
>   
>   		/* If test generator is enabled */
>   		/* do not allow a link from CSIPHY to CSID */
> -		if (csid->testgen_mode->cur.val != 0)
> +		if (csid->testgen.nmodes != CSID_PAYLOAD_MODE_DISABLED &&
> +		    csid->testgen_mode->cur.val != 0)
>   			return -EBUSY;
>   
>   		sd = media_entity_to_v4l2_subdev(remote->entity);
> @@ -1360,24 +1365,27 @@ int msm_csid_register_entity(struct csid_device *csid,
>   		 MSM_CSID_NAME, csid->id);
>   	v4l2_set_subdevdata(sd, csid);
>   
> -	ret = v4l2_ctrl_handler_init(&csid->ctrls, 1);
> -	if (ret < 0) {
> -		dev_err(dev, "Failed to init ctrl handler: %d\n", ret);
> -		return ret;
> -	}
> +	if (csid->testgen.nmodes != CSID_PAYLOAD_MODE_DISABLED) {
> +		ret = v4l2_ctrl_handler_init(&csid->ctrls, 1);
> +		if (ret < 0) {
> +			dev_err(dev, "Failed to init ctrl handler: %d\n", ret);
> +			return ret;
> +		}
>   
> -	csid->testgen_mode = v4l2_ctrl_new_std_menu_items(&csid->ctrls,
> -				&csid_ctrl_ops, V4L2_CID_TEST_PATTERN,
> -				csid->testgen.nmodes, 0, 0,
> -				csid->testgen.modes);
> +		csid->testgen_mode =
> +			v4l2_ctrl_new_std_menu_items(&csid->ctrls,
> +						     &csid_ctrl_ops, V4L2_CID_TEST_PATTERN,
> +						     csid->testgen.nmodes, 0, 0,
> +						     csid->testgen.modes);
>   
> -	if (csid->ctrls.error) {
> -		dev_err(dev, "Failed to init ctrl: %d\n", csid->ctrls.error);
> -		ret = csid->ctrls.error;
> -		goto free_ctrl;
> -	}
> +		if (csid->ctrls.error) {
> +			dev_err(dev, "Failed to init ctrl: %d\n", csid->ctrls.error);
> +			ret = csid->ctrls.error;
> +			goto free_ctrl;
> +		}
>   
> -	csid->subdev.ctrl_handler = &csid->ctrls;
> +		csid->subdev.ctrl_handler = &csid->ctrls;
> +	}
>   
>   	ret = csid_init_formats(sd, NULL);
>   	if (ret < 0) {
> @@ -1408,7 +1416,8 @@ int msm_csid_register_entity(struct csid_device *csid,
>   media_cleanup:
>   	media_entity_cleanup(&sd->entity);
>   free_ctrl:
> -	v4l2_ctrl_handler_free(&csid->ctrls);
> +	if (csid->testgen.nmodes != CSID_PAYLOAD_MODE_DISABLED)
> +		v4l2_ctrl_handler_free(&csid->ctrls);
>   
>   	return ret;
>   }
> @@ -1421,7 +1430,8 @@ void msm_csid_unregister_entity(struct csid_device *csid)
>   {
>   	v4l2_device_unregister_subdev(&csid->subdev);
>   	media_entity_cleanup(&csid->subdev.entity);
> -	v4l2_ctrl_handler_free(&csid->ctrls);
> +	if (csid->testgen.nmodes != CSID_PAYLOAD_MODE_DISABLED)
> +		v4l2_ctrl_handler_free(&csid->ctrls);
>   }
>   
>   inline bool csid_is_lite(struct csid_device *csid)

The TPG on the RB5 has a known bug that not all test patterns work. I 
verified that the coloured box TPG still works after this change.

Like so:

# colour bars test pattern 9
media-ctl --reset
yavta --no-query -w '0x009f0903 9' /dev/v4l-subdev6
yavta --list /dev/v4l-subdev6
media-ctl -d /dev/media0 -V '"msm_csid0":0[fmt:SGRBG10_1X10/3280x2464]'
media-ctl -d /dev/media0 -V '"msm_vfe0_rdi0":0[fmt:SGRBG10_1X10/3280x2464]'
media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
media-ctl -d /dev/media0 -p
yavta -B capture-mplane --capture=5 -n 5 -I -f SGRBG10P -s 3280x2464 
--file=TPG-SGRBG10-3280x2464-000-#.bin /dev/video0

I think we had some confusion about the TPG regressing on v6/v7 of this 
patch but, I suspect the wrong test pattern was tested.

This works as expected for me.

Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # qrb5165 rb5

Re: [PATCH v8 05/16] media: qcom: camss: csiphy-3ph: Move CSIPHY variables to data field inside csiphy struct

[Laurentiu Tudor]

On 1/8/25 16:37, Depeng Shao wrote:
> From: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
> 
> A .data field in the csiphy device structure allows us to extend out the
> register layout of the three phase capable CSIPHY layer.
> 
> Move the existing lane configuration structure to an encapsulating
> structure -> struct csiphy_device_regs which is derived from the .data
> field populated at PHY init time, as opposed to calculated at lane
> configuration.
> 
> Reviewed-by: default avatarVladimir Zapolskiy <vladimir.zapolskiy@linaro.org>

Nit: Something's not right with this tag.

---
Best Regards, Laurentiu

> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
> Signed-off-by: Depeng Shao <quic_depengs@quicinc.com>
> ---
>   .../qcom/camss/camss-csiphy-3ph-1-0.c         | 54 ++++++++++---------
>   .../media/platform/qcom/camss/camss-csiphy.h  |  6 +++
>   2 files changed, 36 insertions(+), 24 deletions(-)
> 
> diff --git a/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c b/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c
> index b283df7634bb..39cc7109ccf0 100644
> --- a/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c
> +++ b/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c
> @@ -470,32 +470,10 @@ static void csiphy_gen1_config_lanes(struct csiphy_device *csiphy,
>   static void csiphy_gen2_config_lanes(struct csiphy_device *csiphy,
>   				     u8 settle_cnt)
>   {
> -	const struct csiphy_lane_regs *r;
> -	int i, array_size;
> +	const struct csiphy_lane_regs *r = csiphy->regs->lane_regs;
> +	int i, array_size = csiphy->regs->lane_array_size;
>   	u32 val;
>   
> -	switch (csiphy->camss->res->version) {
> -	case CAMSS_7280:
> -		r = &lane_regs_sm8250[0];
> -		array_size = ARRAY_SIZE(lane_regs_sm8250);
> -		break;
> -	case CAMSS_8250:
> -		r = &lane_regs_sm8250[0];
> -		array_size = ARRAY_SIZE(lane_regs_sm8250);
> -		break;
> -	case CAMSS_8280XP:
> -		r = &lane_regs_sc8280xp[0];
> -		array_size = ARRAY_SIZE(lane_regs_sc8280xp);
> -		break;
> -	case CAMSS_845:
> -		r = &lane_regs_sdm845[0];
> -		array_size = ARRAY_SIZE(lane_regs_sdm845);
> -		break;
> -	default:
> -		WARN(1, "unknown cspi version\n");
> -		return;
> -	}
> -
>   	for (i = 0; i < array_size; i++, r++) {
>   		switch (r->csiphy_param_type) {
>   		case CSIPHY_SETTLE_CNT_LOWER_BYTE:
> @@ -588,6 +566,34 @@ static void csiphy_lanes_disable(struct csiphy_device *csiphy,
>   
>   static int csiphy_init(struct csiphy_device *csiphy)
>   {
> +	struct device *dev = csiphy->camss->dev;
> +	struct csiphy_device_regs *regs;
> +
> +	regs = devm_kmalloc(dev, sizeof(*regs), GFP_KERNEL);
> +	if (!regs)
> +		return -ENOMEM;
> +
> +	csiphy->regs = regs;
> +
> +	switch (csiphy->camss->res->version) {
> +	case CAMSS_845:
> +		regs->lane_regs = &lane_regs_sdm845[0];
> +		regs->lane_array_size = ARRAY_SIZE(lane_regs_sdm845);
> +		break;
> +	case CAMSS_7280:
> +	case CAMSS_8250:
> +		regs->lane_regs = &lane_regs_sm8250[0];
> +		regs->lane_array_size = ARRAY_SIZE(lane_regs_sm8250);
> +		break;
> +	case CAMSS_8280XP:
> +		regs->lane_regs = &lane_regs_sc8280xp[0];
> +		regs->lane_array_size = ARRAY_SIZE(lane_regs_sc8280xp);
> +		break;
> +	default:
> +		WARN(1, "unknown csiphy version\n");
> +		return -ENODEV;
> +	}
> +
>   	return 0;
>   }
>   
> diff --git a/drivers/media/platform/qcom/camss/camss-csiphy.h b/drivers/media/platform/qcom/camss/camss-csiphy.h
> index 49393dfd5215..4d731597fed7 100644
> --- a/drivers/media/platform/qcom/camss/camss-csiphy.h
> +++ b/drivers/media/platform/qcom/camss/camss-csiphy.h
> @@ -85,6 +85,11 @@ struct csiphy_subdev_resources {
>   	const struct csiphy_formats *formats;
>   };
>   
> +struct csiphy_device_regs {
> +	const struct csiphy_lane_regs *lane_regs;
> +	int lane_array_size;
> +};
> +
>   struct csiphy_device {
>   	struct camss *camss;
>   	u8 id;
> @@ -103,6 +108,7 @@ struct csiphy_device {
>   	struct csiphy_config cfg;
>   	struct v4l2_mbus_framefmt fmt[MSM_CSIPHY_PADS_NUM];
>   	const struct csiphy_subdev_resources *res;
> +	struct csiphy_device_regs *regs;
>   };
>   
>   struct camss_subdev_resources;

Re: [PATCH v8 05/16] media: qcom: camss: csiphy-3ph: Move CSIPHY variables to data field inside csiphy struct

[Bryan O'Donoghue]

On 15/01/2025 18:01, Laurentiu Tudor wrote:
>> Reviewed-by: default avatarVladimir Zapolskiy 
>> <vladimir.zapolskiy@linaro.org>
> 
> Nit: Something's not right with this tag.
> 
> ---
> Best Regards, Laurentiu

Doh.

@Hans could you possibly drop the "default avatar" when applying ?

---
bod

Re: [PATCH v8 05/16] media: qcom: camss: csiphy-3ph: Move CSIPHY variables to data field inside csiphy struct

[Vladimir Zapolskiy]

On 1/15/25 23:01, Bryan O'Donoghue wrote:
> On 15/01/2025 18:01, Laurentiu Tudor wrote:
>>> Reviewed-by: default avatarVladimir Zapolskiy
>>> <vladimir.zapolskiy@linaro.org>
>>
>> Nit: Something's not right with this tag.

Thank you for reporting. The original uncorrupted tag comes from this message:

https://lore.kernel.org/all/4fdf4f1c-fac0-4c85-8154-45f797c6acfd@linaro.org/

>> ---
>> Best Regards, Laurentiu
> 
> Doh.
> 
> @Hans could you possibly drop the "default avatar" when applying ?
> 

FWIW this particular problem has been fixed in v9, while the v9 series
itself should gain some time to be reviewed/tested.

--
Best wishes,
Vladimir

Re: [PATCH v8 05/16] media: qcom: camss: csiphy-3ph: Move CSIPHY variables to data field inside csiphy struct

[Bryan O'Donoghue]

On 15/01/2025 21:15, Vladimir Zapolskiy wrote:
>>
>> @Hans could you possibly drop the "default avatar" when applying ?
>>
> 
> FWIW this particular problem has been fixed in v9, while the v9 series
> itself should gain some time to be reviewed/tested.

Ah, this is V8.

I didn't see.

---
bod