From: Ahmad Fatoum <a.fatoum@pengutronix.de>
To: Richard Zhu <hongxing.zhu@nxp.com>,
l.stach@pengutronix.de, shawnguo@kernel.org,
lpieralisi@kernel.org, robh+dt@kernel.org,
krzysztof.kozlowski+dt@linaro.org
Cc: devicetree@vger.kernel.org, linux-pci@vger.kernel.org,
linux-kernel@vger.kernel.org, linux-imx@nxp.com,
kernel@pengutronix.de, linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH 0/9] Add legacy i.MX PCIe EP mode supports
Date: Wed, 2 Aug 2023 08:51:37 +0200 [thread overview]
Message-ID: <7f98d5f3-eb5b-d98b-a5ab-a7f54319c99a@pengutronix.de> (raw)
In-Reply-To: <1690956412-2439-1-git-send-email-hongxing.zhu@nxp.com>
Hello Richard,
On 02.08.23 08:06, Richard Zhu wrote:
> Add legacy 32bit i.MX PCIe EP mode support
>
> The PCI controller contained in i.MX6/7 legacy SOCs is one dual mode
> PCIe controller, and can work either as RC or EP.
>
> This series add i.MX6/7 PCIe EP mode supports. And had been verified
> on i.MX6 sabresd and i.MX7 SDB boards.
>
> In the verification, one board PCIe is used as RC, the other one is used
> as EP.
> Use the cross TX/RX differential cable connect the two PCIe ports of
> these two boards.
>
> +-----------+ +------------+
> | PCIe TX |<-------------->|PCIe RX |
> | | | |
> | Board | | Board |
> | | | |
> | PCIe RX |<-------------->|PCIe TX |
> +-----------+ +------------+
I am curious what software you are running on both sides to test?
Do you use CONFIG_PCI_EPF_TEST? What do you run on RC side?
Thanks,
Ahmad
>
> [PATCH 1/9] dt-bindings: PCI: fsl,imx6q: Add i.MX6Q and i.MX6QP PCIe
> [PATCH 2/9] dt-bindings: PCI: fsl,imx6q: Add i.MX6SX PCIe EP
> [PATCH 3/9] dt-bindings: PCI: fsl,imx6q: Add i.MX7D PCIe EP
> [PATCH 4/9] arm: dts: nxp: Add i.MX6QDL and i.MX6QP PCIe EP supports
> [PATCH 5/9] arm: dts: nxp: Add i.MX6SX PCIe EP support
> [PATCH 6/9] arm: dts: nxp: Add i.MX7D PCIe EP support
> [PATCH 7/9] PCI: imx6: Add i.MX6Q and i.MX6QP PCIe EP supports
> [PATCH 8/9] PCI: imx6: Add i.MX6SX PCIe EP support
> [PATCH 9/9] PCI: imx6: Add i.MX7D PCIe EP support
>
> Documentation/devicetree/bindings/pci/fsl,imx6q-pcie-ep.yaml | 50 +++++++++++++++++++++++++++++++++++++++++----
> arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi | 14 +++++++++++++
> arch/arm/boot/dts/nxp/imx/imx6qp.dtsi | 4 ++++
> arch/arm/boot/dts/nxp/imx/imx6sx.dtsi | 17 +++++++++++++++
> arch/arm/boot/dts/nxp/imx/imx7d.dtsi | 27 ++++++++++++++++++++++++
> drivers/pci/controller/dwc/pci-imx6.c | 93 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++-
> 6 files changed, 200 insertions(+), 5 deletions(-)
>
>
>
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
next prev parent reply other threads:[~2023-08-02 6:52 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-08-02 6:06 [PATCH 0/9] Add legacy i.MX PCIe EP mode supports Richard Zhu
2023-08-02 6:06 ` [PATCH 1/9] dt-bindings: PCI: fsl,imx6q: Add i.MX6Q and i.MX6QP PCIe EP compatibles Richard Zhu
2023-08-02 6:06 ` [PATCH 2/9] dt-bindings: PCI: fsl,imx6q: Add i.MX6SX " Richard Zhu
2023-08-02 6:06 ` [PATCH 3/9] dt-bindings: PCI: fsl,imx6q: Add i.MX7D " Richard Zhu
2023-08-02 6:06 ` [PATCH 4/9] arm: dts: nxp: Add i.MX6QDL and i.MX6QP PCIe EP supports Richard Zhu
2023-08-02 6:06 ` [PATCH 5/9] arm: dts: nxp: Add i.MX6SX PCIe EP support Richard Zhu
2023-08-02 6:06 ` [PATCH 6/9] arm: dts: nxp: Add i.MX7D " Richard Zhu
2023-08-02 6:06 ` [PATCH 7/9] PCI: imx6: Add i.MX6Q and i.MX6QP PCIe EP supports Richard Zhu
2023-08-02 21:54 ` Frank Li
2023-08-03 2:42 ` Hongxing Zhu
2023-08-02 6:06 ` [PATCH 8/9] PCI: imx6: Add i.MX6SX PCIe EP support Richard Zhu
2023-08-02 6:06 ` [PATCH 9/9] PCI: imx6: Add i.MX7D " Richard Zhu
2023-08-02 6:51 ` Ahmad Fatoum [this message]
2023-08-02 14:08 ` [PATCH 0/9] Add legacy i.MX PCIe EP mode supports Hongxing Zhu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=7f98d5f3-eb5b-d98b-a5ab-a7f54319c99a@pengutronix.de \
--to=a.fatoum@pengutronix.de \
--cc=devicetree@vger.kernel.org \
--cc=hongxing.zhu@nxp.com \
--cc=kernel@pengutronix.de \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=l.stach@pengutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-imx@nxp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=lpieralisi@kernel.org \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).