[PATCH 0/6] phy: realtek: usb2: support for RTL9607C USB2 PHY

[PATCH 0/6] phy: realtek: usb2: support for RTL9607C USB2 PHY

[Rustam Adilov]

This patch series for Realtek USB2 PHY driver adds support for RTL9607C
USB2 PHY.

RTL9607C is a big endian MIPS CPU which is quite far from RTD series SoCs
supported by realtek usb2 phy driver, but the phy initilization is found
to be very indentical in most areas.

Most of the code was based on the Realtek's usb driver from the GPL tarball
in [1] and adjusted to fit into the realtek usb2 phy driver code format.

The patch series was split into smaller patches that add/change something
in the driver that are not exactly related to RTL9607C and that also
helps for easier review. That also means, patch 5 depends on all the prior
patches that come before it.

USB2 PHY on RTL9607C is primarly used for its internal OHCI/EHCI controllers.

[1] - https://github.com/jameywine/GPL-for-GP3000/blob/main/linux-5.10.x/arch/mips/rtl9607c/usb.c

Rustam Adilov (6):
  phy: realtek: usb2: introduce vstatus/new_reg_req variables to driver
    data
  phy: realtek: usb2: introduce read and write functions to driver data
  dt-bindings: phy: realtek,usb2phy.yaml: extend for resets and RTL9607C
    support
  phy: realtek: usb2: introduce reset controller struct
  phy: realtek: usb2: add support for RTL9607C USB2 PHY
  phy: realtek: usb2: Make configs available for MACH_REALTEK_RTL

 .../bindings/phy/realtek,usb2phy.yaml         |  23 ++-
 drivers/phy/realtek/Kconfig                   |   2 +-
 drivers/phy/realtek/phy-rtk-usb2.c            | 189 ++++++++++++++++--
 3 files changed, 194 insertions(+), 20 deletions(-)

-- 
2.53.0

[PATCH 1/6] phy: realtek: usb2: introduce vstatus/new_reg_req variables to driver data

[Rustam Adilov]

In RTL9607C SoC, the vstatus register is located at a certain offset from
the base and so introduce the vstatus_offset to handle it.

Busy bit of the vstatus and new_reg_req bit are also different and so
introduce these variables to the driver data as well.

Add these variables to the pre-existing phy cfg structs for RTD SoCs and
assign them the default values.

Co-developed-by: Michael Zavertkin <misha.zavertkin@mail.ru>
Signed-off-by: Michael Zavertkin <misha.zavertkin@mail.ru>
Signed-off-by: Rustam Adilov <adilov@disroot.org>
---
 drivers/phy/realtek/phy-rtk-usb2.c | 59 ++++++++++++++++++++++++------
 1 file changed, 48 insertions(+), 11 deletions(-)

diff --git a/drivers/phy/realtek/phy-rtk-usb2.c b/drivers/phy/realtek/phy-rtk-usb2.c
index 248550ef98ca..f5d2f0c3376a 100644
--- a/drivers/phy/realtek/phy-rtk-usb2.c
+++ b/drivers/phy/realtek/phy-rtk-usb2.c
@@ -64,6 +64,9 @@ struct phy_reg {
 	void __iomem *reg_wrap_vstatus;
 	void __iomem *reg_gusb2phyacc0;
 	int vstatus_index;
+	int vstatus_offset;
+	int vstatus_busy;
+	int new_reg_req;
 };
 
 struct phy_data {
@@ -96,6 +99,9 @@ struct phy_cfg {
 	bool do_toggle_driving;
 	bool use_default_parameter;
 	bool is_double_sensitivity_mode;
+	int vstatus_offset;
+	int vstatus_busy;
+	int new_reg_req;
 };
 
 struct phy_parameter {
@@ -162,21 +168,21 @@ static char rtk_phy_read(struct phy_reg *phy_reg, char addr)
 	addr -= OFFEST_PHY_READ;
 
 	/* polling until VBusy == 0 */
-	ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+	ret = utmi_wait_register(reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
 	if (ret)
 		return (char)ret;
 
 	/* VCtrl = low nibble of addr, and set PHY_NEW_REG_REQ */
-	val = PHY_NEW_REG_REQ | (GET_LOW_NIBBLE(addr) << PHY_VCTRL_SHIFT);
+	val = phy_reg->new_reg_req | (GET_LOW_NIBBLE(addr) << PHY_VCTRL_SHIFT);
 	writel(val, reg_gusb2phyacc0);
-	ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+	ret = utmi_wait_register(reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
 	if (ret)
 		return (char)ret;
 
 	/* VCtrl = high nibble of addr, and set PHY_NEW_REG_REQ */
-	val = PHY_NEW_REG_REQ | (GET_HIGH_NIBBLE(addr) << PHY_VCTRL_SHIFT);
+	val = phy_reg->new_reg_req | (GET_HIGH_NIBBLE(addr) << PHY_VCTRL_SHIFT);
 	writel(val, reg_gusb2phyacc0);
-	ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+	ret = utmi_wait_register(reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
 	if (ret)
 		return (char)ret;
 
@@ -194,25 +200,25 @@ static int rtk_phy_write(struct phy_reg *phy_reg, char addr, char data)
 	int ret = 0;
 
 	/* write data to VStatusOut2 (data output to phy) */
-	writel((u32)data << shift_bits, reg_wrap_vstatus);
+	writel((u32)data << shift_bits, reg_wrap_vstatus + phy_reg->vstatus_offset);
 
-	ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+	ret = utmi_wait_register(reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
 	if (ret)
 		return ret;
 
 	/* VCtrl = low nibble of addr, set PHY_NEW_REG_REQ */
-	val = PHY_NEW_REG_REQ | (GET_LOW_NIBBLE(addr) << PHY_VCTRL_SHIFT);
+	val = phy_reg->new_reg_req | (GET_LOW_NIBBLE(addr) << PHY_VCTRL_SHIFT);
 
 	writel(val, reg_gusb2phyacc0);
-	ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+	ret = utmi_wait_register(reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
 	if (ret)
 		return ret;
 
 	/* VCtrl = high nibble of addr, set PHY_NEW_REG_REQ */
-	val = PHY_NEW_REG_REQ | (GET_HIGH_NIBBLE(addr) << PHY_VCTRL_SHIFT);
+	val = phy_reg->new_reg_req | (GET_HIGH_NIBBLE(addr) << PHY_VCTRL_SHIFT);
 
 	writel(val, reg_gusb2phyacc0);
-	ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+	ret = utmi_wait_register(reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
 	if (ret)
 		return ret;
 
@@ -957,6 +963,7 @@ static int get_phy_data_by_efuse(struct rtk_phy *rtk_phy,
 
 static int parse_phy_data(struct rtk_phy *rtk_phy)
 {
+	struct phy_cfg *phy_cfg = rtk_phy->phy_cfg;
 	struct device *dev = rtk_phy->dev;
 	struct device_node *np = dev->of_node;
 	struct phy_parameter *phy_parameter;
@@ -974,6 +981,9 @@ static int parse_phy_data(struct rtk_phy *rtk_phy)
 		phy_parameter->phy_reg.reg_wrap_vstatus = of_iomap(np, 0);
 		phy_parameter->phy_reg.reg_gusb2phyacc0 = of_iomap(np, 1) + index;
 		phy_parameter->phy_reg.vstatus_index = index;
+		phy_parameter->phy_reg.vstatus_offset = phy_cfg->vstatus_offset;
+		phy_parameter->phy_reg.vstatus_busy = phy_cfg->vstatus_busy;
+		phy_parameter->phy_reg.new_reg_req = phy_cfg->new_reg_req;
 
 		if (of_property_read_bool(np, "realtek,inverse-hstx-sync-clock"))
 			phy_parameter->inverse_hstx_sync_clock = true;
@@ -1085,6 +1095,9 @@ static const struct phy_cfg rtd1295_phy_cfg = {
 	.driving_updated_for_dev_dis = 0xf,
 	.use_default_parameter = false,
 	.is_double_sensitivity_mode = false,
+	.vstatus_offset = 0,
+	.vstatus_busy = PHY_VSTS_BUSY,
+	.new_reg_req = PHY_NEW_REG_REQ,
 };
 
 static const struct phy_cfg rtd1395_phy_cfg = {
@@ -1109,6 +1122,9 @@ static const struct phy_cfg rtd1395_phy_cfg = {
 	.driving_updated_for_dev_dis = 0xf,
 	.use_default_parameter = false,
 	.is_double_sensitivity_mode = false,
+	.vstatus_offset = 0,
+	.vstatus_busy = PHY_VSTS_BUSY,
+	.new_reg_req = PHY_NEW_REG_REQ,
 };
 
 static const struct phy_cfg rtd1395_phy_cfg_2port = {
@@ -1133,6 +1149,9 @@ static const struct phy_cfg rtd1395_phy_cfg_2port = {
 	.driving_updated_for_dev_dis = 0xf,
 	.use_default_parameter = false,
 	.is_double_sensitivity_mode = false,
+	.vstatus_offset = 0,
+	.vstatus_busy = PHY_VSTS_BUSY,
+	.new_reg_req = PHY_NEW_REG_REQ,
 };
 
 static const struct phy_cfg rtd1619_phy_cfg = {
@@ -1155,6 +1174,9 @@ static const struct phy_cfg rtd1619_phy_cfg = {
 	.driving_updated_for_dev_dis = 0xf,
 	.use_default_parameter = false,
 	.is_double_sensitivity_mode = false,
+	.vstatus_offset = 0,
+	.vstatus_busy = PHY_VSTS_BUSY,
+	.new_reg_req = PHY_NEW_REG_REQ,
 };
 
 static const struct phy_cfg rtd1319_phy_cfg = {
@@ -1181,6 +1203,9 @@ static const struct phy_cfg rtd1319_phy_cfg = {
 	.driving_updated_for_dev_dis = 0xf,
 	.use_default_parameter = false,
 	.is_double_sensitivity_mode = true,
+	.vstatus_offset = 0,
+	.vstatus_busy = PHY_VSTS_BUSY,
+	.new_reg_req = PHY_NEW_REG_REQ,
 };
 
 static const struct phy_cfg rtd1312c_phy_cfg = {
@@ -1206,6 +1231,9 @@ static const struct phy_cfg rtd1312c_phy_cfg = {
 	.driving_updated_for_dev_dis = 0xf,
 	.use_default_parameter = false,
 	.is_double_sensitivity_mode = true,
+	.vstatus_offset = 0,
+	.vstatus_busy = PHY_VSTS_BUSY,
+	.new_reg_req = PHY_NEW_REG_REQ,
 };
 
 static const struct phy_cfg rtd1619b_phy_cfg = {
@@ -1231,6 +1259,9 @@ static const struct phy_cfg rtd1619b_phy_cfg = {
 	.driving_updated_for_dev_dis = 0x8,
 	.use_default_parameter = false,
 	.is_double_sensitivity_mode = true,
+	.vstatus_offset = 0,
+	.vstatus_busy = PHY_VSTS_BUSY,
+	.new_reg_req = PHY_NEW_REG_REQ,
 };
 
 static const struct phy_cfg rtd1319d_phy_cfg = {
@@ -1256,6 +1287,9 @@ static const struct phy_cfg rtd1319d_phy_cfg = {
 	.driving_updated_for_dev_dis = 0x8,
 	.use_default_parameter = false,
 	.is_double_sensitivity_mode = true,
+	.vstatus_offset = 0,
+	.vstatus_busy = PHY_VSTS_BUSY,
+	.new_reg_req = PHY_NEW_REG_REQ,
 };
 
 static const struct phy_cfg rtd1315e_phy_cfg = {
@@ -1282,6 +1316,9 @@ static const struct phy_cfg rtd1315e_phy_cfg = {
 	.driving_updated_for_dev_dis = 0x8,
 	.use_default_parameter = false,
 	.is_double_sensitivity_mode = true,
+	.vstatus_offset = 0,
+	.vstatus_busy = PHY_VSTS_BUSY,
+	.new_reg_req = PHY_NEW_REG_REQ,
 };
 
 static const struct of_device_id usbphy_rtk_dt_match[] = {
-- 
2.53.0

[PATCH 2/6] phy: realtek: usb2: introduce read and write functions to driver data

[Rustam Adilov]

RTL9607C is a big endian SoC but has little endian USB host controller and
thus, reads and writes to the reg_gusb2phyacc0 should go through
le32_to_cpu and cpu_to_le32 functions respectively. This doesn't apply to
vstatus register though.

To handle this situation, introduce read and write functions to the driver
data and create 2 variations of reads and write function with le32 function
in it and without.

Adjust all instances of utmi_wait_register function to now include the read
function as one of its arguments.

Assign the existing phy configuration for RTD SoCs to the default phy_read
and phy_write functions.

Co-developed-by: Michael Zavertkin <misha.zavertkin@mail.ru>
Signed-off-by: Michael Zavertkin <misha.zavertkin@mail.ru>
Signed-off-by: Rustam Adilov <adilov@disroot.org>
---
 drivers/phy/realtek/phy-rtk-usb2.c | 73 ++++++++++++++++++++++++------
 1 file changed, 60 insertions(+), 13 deletions(-)

diff --git a/drivers/phy/realtek/phy-rtk-usb2.c b/drivers/phy/realtek/phy-rtk-usb2.c
index f5d2f0c3376a..e65b8525b88b 100644
--- a/drivers/phy/realtek/phy-rtk-usb2.c
+++ b/drivers/phy/realtek/phy-rtk-usb2.c
@@ -67,6 +67,9 @@ struct phy_reg {
 	int vstatus_offset;
 	int vstatus_busy;
 	int new_reg_req;
+
+	u32 (*read)(void __iomem *reg);
+	void (*write)(u32 val, void __iomem *reg);
 };
 
 struct phy_data {
@@ -102,6 +105,9 @@ struct phy_cfg {
 	int vstatus_offset;
 	int vstatus_busy;
 	int new_reg_req;
+
+	u32 (*read)(void __iomem *reg);
+	void (*write)(u32 val, void __iomem *reg);
 };
 
 struct phy_parameter {
@@ -128,6 +134,26 @@ struct rtk_phy {
 	struct dentry *debug_dir;
 };
 
+static inline u32 phy_read(void __iomem *reg)
+{
+	return readl(reg);
+}
+
+static inline u32 phy_read_le(void __iomem *reg)
+{
+	return le32_to_cpu(readl(reg));
+}
+
+static inline void phy_write(u32 val, void __iomem *reg)
+{
+	writel(val, reg);
+}
+
+static inline void phy_write_le(u32 val, void __iomem *reg)
+{
+	writel(cpu_to_le32(val), reg);
+}
+
 /* mapping 0xE0 to 0 ... 0xE7 to 7, 0xF0 to 8 ,,, 0xF7 to 15 */
 static inline int page_addr_to_array_index(u8 addr)
 {
@@ -144,12 +170,13 @@ static inline u8 array_index_to_page_addr(int index)
 #define PHY_IO_TIMEOUT_USEC		(50000)
 #define PHY_IO_DELAY_US			(100)
 
-static inline int utmi_wait_register(void __iomem *reg, u32 mask, u32 result)
+static inline int utmi_wait_register(u32 (*read)(void __iomem *reg), void __iomem *reg, u32 mask,
+				     u32 result)
 {
 	int ret;
 	unsigned int val;
 
-	ret = read_poll_timeout(readl, val, ((val & mask) == result),
+	ret = read_poll_timeout(read, val, ((val & mask) == result),
 				PHY_IO_DELAY_US, PHY_IO_TIMEOUT_USEC, false, reg);
 	if (ret) {
 		pr_err("%s can't program USB phy\n", __func__);
@@ -168,25 +195,25 @@ static char rtk_phy_read(struct phy_reg *phy_reg, char addr)
 	addr -= OFFEST_PHY_READ;
 
 	/* polling until VBusy == 0 */
-	ret = utmi_wait_register(reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
+	ret = utmi_wait_register(phy_reg->read, reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
 	if (ret)
 		return (char)ret;
 
 	/* VCtrl = low nibble of addr, and set PHY_NEW_REG_REQ */
 	val = phy_reg->new_reg_req | (GET_LOW_NIBBLE(addr) << PHY_VCTRL_SHIFT);
-	writel(val, reg_gusb2phyacc0);
-	ret = utmi_wait_register(reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
+	phy_reg->write(val, reg_gusb2phyacc0);
+	ret = utmi_wait_register(phy_reg->read, reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
 	if (ret)
 		return (char)ret;
 
 	/* VCtrl = high nibble of addr, and set PHY_NEW_REG_REQ */
 	val = phy_reg->new_reg_req | (GET_HIGH_NIBBLE(addr) << PHY_VCTRL_SHIFT);
-	writel(val, reg_gusb2phyacc0);
-	ret = utmi_wait_register(reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
+	phy_reg->write(val, reg_gusb2phyacc0);
+	ret = utmi_wait_register(phy_reg->read, reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
 	if (ret)
 		return (char)ret;
 
-	val = readl(reg_gusb2phyacc0);
+	val = phy_reg->read(reg_gusb2phyacc0);
 
 	return (char)(val & PHY_REG_DATA_MASK);
 }
@@ -202,23 +229,23 @@ static int rtk_phy_write(struct phy_reg *phy_reg, char addr, char data)
 	/* write data to VStatusOut2 (data output to phy) */
 	writel((u32)data << shift_bits, reg_wrap_vstatus + phy_reg->vstatus_offset);
 
-	ret = utmi_wait_register(reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
+	ret = utmi_wait_register(phy_reg->read, reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
 	if (ret)
 		return ret;
 
 	/* VCtrl = low nibble of addr, set PHY_NEW_REG_REQ */
 	val = phy_reg->new_reg_req | (GET_LOW_NIBBLE(addr) << PHY_VCTRL_SHIFT);
 
-	writel(val, reg_gusb2phyacc0);
-	ret = utmi_wait_register(reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
+	phy_reg->write(val, reg_gusb2phyacc0);
+	ret = utmi_wait_register(phy_reg->read, reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
 	if (ret)
 		return ret;
 
 	/* VCtrl = high nibble of addr, set PHY_NEW_REG_REQ */
 	val = phy_reg->new_reg_req | (GET_HIGH_NIBBLE(addr) << PHY_VCTRL_SHIFT);
 
-	writel(val, reg_gusb2phyacc0);
-	ret = utmi_wait_register(reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
+	phy_reg->write(val, reg_gusb2phyacc0);
+	ret = utmi_wait_register(phy_reg->read, reg_gusb2phyacc0, phy_reg->vstatus_busy, 0);
 	if (ret)
 		return ret;
 
@@ -984,6 +1011,8 @@ static int parse_phy_data(struct rtk_phy *rtk_phy)
 		phy_parameter->phy_reg.vstatus_offset = phy_cfg->vstatus_offset;
 		phy_parameter->phy_reg.vstatus_busy = phy_cfg->vstatus_busy;
 		phy_parameter->phy_reg.new_reg_req = phy_cfg->new_reg_req;
+		phy_parameter->phy_reg.read = phy_cfg->read;
+		phy_parameter->phy_reg.write = phy_cfg->write;
 
 		if (of_property_read_bool(np, "realtek,inverse-hstx-sync-clock"))
 			phy_parameter->inverse_hstx_sync_clock = true;
@@ -1098,6 +1127,8 @@ static const struct phy_cfg rtd1295_phy_cfg = {
 	.vstatus_offset = 0,
 	.vstatus_busy = PHY_VSTS_BUSY,
 	.new_reg_req = PHY_NEW_REG_REQ,
+	.read = phy_read,
+	.write = phy_write,
 };
 
 static const struct phy_cfg rtd1395_phy_cfg = {
@@ -1125,6 +1156,8 @@ static const struct phy_cfg rtd1395_phy_cfg = {
 	.vstatus_offset = 0,
 	.vstatus_busy = PHY_VSTS_BUSY,
 	.new_reg_req = PHY_NEW_REG_REQ,
+	.read = phy_read,
+	.write = phy_write,
 };
 
 static const struct phy_cfg rtd1395_phy_cfg_2port = {
@@ -1152,6 +1185,8 @@ static const struct phy_cfg rtd1395_phy_cfg_2port = {
 	.vstatus_offset = 0,
 	.vstatus_busy = PHY_VSTS_BUSY,
 	.new_reg_req = PHY_NEW_REG_REQ,
+	.read = phy_read,
+	.write = phy_write,
 };
 
 static const struct phy_cfg rtd1619_phy_cfg = {
@@ -1177,6 +1212,8 @@ static const struct phy_cfg rtd1619_phy_cfg = {
 	.vstatus_offset = 0,
 	.vstatus_busy = PHY_VSTS_BUSY,
 	.new_reg_req = PHY_NEW_REG_REQ,
+	.read = phy_read,
+	.write = phy_write,
 };
 
 static const struct phy_cfg rtd1319_phy_cfg = {
@@ -1206,6 +1243,8 @@ static const struct phy_cfg rtd1319_phy_cfg = {
 	.vstatus_offset = 0,
 	.vstatus_busy = PHY_VSTS_BUSY,
 	.new_reg_req = PHY_NEW_REG_REQ,
+	.read = phy_read,
+	.write = phy_write,
 };
 
 static const struct phy_cfg rtd1312c_phy_cfg = {
@@ -1234,6 +1273,8 @@ static const struct phy_cfg rtd1312c_phy_cfg = {
 	.vstatus_offset = 0,
 	.vstatus_busy = PHY_VSTS_BUSY,
 	.new_reg_req = PHY_NEW_REG_REQ,
+	.read = phy_read,
+	.write = phy_write,
 };
 
 static const struct phy_cfg rtd1619b_phy_cfg = {
@@ -1262,6 +1303,8 @@ static const struct phy_cfg rtd1619b_phy_cfg = {
 	.vstatus_offset = 0,
 	.vstatus_busy = PHY_VSTS_BUSY,
 	.new_reg_req = PHY_NEW_REG_REQ,
+	.read = phy_read,
+	.write = phy_write,
 };
 
 static const struct phy_cfg rtd1319d_phy_cfg = {
@@ -1290,6 +1333,8 @@ static const struct phy_cfg rtd1319d_phy_cfg = {
 	.vstatus_offset = 0,
 	.vstatus_busy = PHY_VSTS_BUSY,
 	.new_reg_req = PHY_NEW_REG_REQ,
+	.read = phy_read,
+	.write = phy_write,
 };
 
 static const struct phy_cfg rtd1315e_phy_cfg = {
@@ -1319,6 +1364,8 @@ static const struct phy_cfg rtd1315e_phy_cfg = {
 	.vstatus_offset = 0,
 	.vstatus_busy = PHY_VSTS_BUSY,
 	.new_reg_req = PHY_NEW_REG_REQ,
+	.read = phy_read,
+	.write = phy_write,
 };
 
 static const struct of_device_id usbphy_rtk_dt_match[] = {
-- 
2.53.0

[PATCH 3/6] dt-bindings: phy: realtek,usb2phy.yaml: extend for resets and RTL9607C support

[Rustam Adilov]

Add the "realtek,rtl9607-usb2phy" compatible for USB2 PHY on the RTL9607C
SoC series.

Add a resets property to properties to describe the usb2phy reset line.

In RTL9607C, USB2 PHY reset line is from "IP Enable controller" which is
multipurpose and handle activating various SoC peripherals.

It is unclear whether RTD SoCs have something similar to that but make it
available to them anyway.

RTL9607C requires the "resets" to be specified so add the corresponding
if check for the "realtek,rtl9607-usb2phy" compatible.

Signed-off-by: Rustam Adilov <adilov@disroot.org>
---
 .../bindings/phy/realtek,usb2phy.yaml         | 23 ++++++++++++++++++-
 1 file changed, 22 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/phy/realtek,usb2phy.yaml b/Documentation/devicetree/bindings/phy/realtek,usb2phy.yaml
index 9911ada39ee7..cdc7b72e5f60 100644
--- a/Documentation/devicetree/bindings/phy/realtek,usb2phy.yaml
+++ b/Documentation/devicetree/bindings/phy/realtek,usb2phy.yaml
@@ -11,10 +11,12 @@ maintainers:
   - Stanley Chang <stanley_chang@realtek.com>
 
 description: |
-  Realtek USB 2.0 PHY support the digital home center (DHC) RTD series SoCs.
+  Realtek USB 2.0 PHY support the digital home center (DHC) RTD and
+  RTL9607C series SoCs.
   The USB 2.0 PHY driver is designed to support the XHCI controller. The SoCs
   support multiple XHCI controllers. One PHY device node maps to one XHCI
   controller.
+  This driver also supports the OCHI and EHCI controllers.
 
   RTD1295/RTD1619 SoCs USB
   The USB architecture includes three XHCI controllers.
@@ -57,6 +59,12 @@ description: |
   XHCI controller#1 -- usb2phy -- phy#0
   XHCI controller#2 -- usb2phy -- phy#0
 
+  RTL9607C SoCs USB
+  The USB architecture includes OHCI and EHCI controllers.
+  Both of them map to one USB2.0 PHY.
+  OHCI controller#0 -- usb2phy -- phy#0
+  EHCI controller#0 -- usb2phy -- phy#0
+
 properties:
   compatible:
     enum:
@@ -69,6 +77,7 @@ properties:
       - realtek,rtd1395-usb2phy-2port
       - realtek,rtd1619-usb2phy
       - realtek,rtd1619b-usb2phy
+      - realtek,rtl9607-usb2phy
 
   reg:
     items:
@@ -130,6 +139,9 @@ properties:
     minimum: -8
     maximum: 8
 
+  resets:
+    maxItems: 1
+
 required:
   - compatible
   - reg
@@ -157,6 +169,15 @@ allOf:
     then:
       properties:
         realtek,driving-level-compensate: false
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - realtek,rtl9607-usb2phy
+    then:
+      required:
+        - resets
 
 additionalProperties: false
 
-- 
2.53.0

Re: [PATCH 3/6] dt-bindings: phy: realtek,usb2phy.yaml: extend for resets and RTL9607C support

[Krzysztof Kozlowski]

On Fri, Mar 27, 2026 at 12:34:16AM +0500, Rustam Adilov wrote:
>  description: |
> -  Realtek USB 2.0 PHY support the digital home center (DHC) RTD series SoCs.
> +  Realtek USB 2.0 PHY support the digital home center (DHC) RTD and
> +  RTL9607C series SoCs.
>    The USB 2.0 PHY driver is designed to support the XHCI controller. The SoCs
>    support multiple XHCI controllers. One PHY device node maps to one XHCI
>    controller.
> +  This driver also supports the OCHI and EHCI controllers.

Hardware is fixed, does not change. Don't reference your driver changes
here.

>  
>    RTD1295/RTD1619 SoCs USB
>    The USB architecture includes three XHCI controllers.
> @@ -57,6 +59,12 @@ description: |
>    XHCI controller#1 -- usb2phy -- phy#0
>    XHCI controller#2 -- usb2phy -- phy#0
>  
> +  RTL9607C SoCs USB
> +  The USB architecture includes OHCI and EHCI controllers.
> +  Both of them map to one USB2.0 PHY.
> +  OHCI controller#0 -- usb2phy -- phy#0
> +  EHCI controller#0 -- usb2phy -- phy#0
> +
>  properties:
>    compatible:
>      enum:
> @@ -69,6 +77,7 @@ properties:
>        - realtek,rtd1395-usb2phy-2port
>        - realtek,rtd1619-usb2phy
>        - realtek,rtd1619b-usb2phy
> +      - realtek,rtl9607-usb2phy
>  
>    reg:
>      items:
> @@ -130,6 +139,9 @@ properties:
>      minimum: -8
>      maximum: 8
>  
> +  resets:
> +    maxItems: 1
> +
>  required:
>    - compatible
>    - reg
> @@ -157,6 +169,15 @@ allOf:
>      then:
>        properties:
>          realtek,driving-level-compensate: false
> +  - if:
> +      properties:
> +        compatible:
> +          contains:
> +            enum:
> +              - realtek,rtl9607-usb2phy
> +    then:
> +      required:
> +        - resets

If it is unclear, they might not have it so,

else: ... :false

see example-schema.

Best regards,
Krzysztof

Re: [PATCH 3/6] dt-bindings: phy: realtek,usb2phy.yaml: extend for resets and RTL9607C support

[Rustam Adilov]

On 2026-03-27 08:28, Krzysztof Kozlowski wrote:
> On Fri, Mar 27, 2026 at 12:34:16AM +0500, Rustam Adilov wrote:
>>  description: |
>> -  Realtek USB 2.0 PHY support the digital home center (DHC) RTD series SoCs.
>> +  Realtek USB 2.0 PHY support the digital home center (DHC) RTD and
>> +  RTL9607C series SoCs.
>>    The USB 2.0 PHY driver is designed to support the XHCI controller. The SoCs
>>    support multiple XHCI controllers. One PHY device node maps to one XHCI
>>    controller.
>> +  This driver also supports the OCHI and EHCI controllers.
> 
> Hardware is fixed, does not change. Don't reference your driver changes
> here.

Will remove this line.
>>  
>>    RTD1295/RTD1619 SoCs USB
>>    The USB architecture includes three XHCI controllers.
>> @@ -57,6 +59,12 @@ description: |
>>    XHCI controller#1 -- usb2phy -- phy#0
>>    XHCI controller#2 -- usb2phy -- phy#0
>>  
>> +  RTL9607C SoCs USB
>> +  The USB architecture includes OHCI and EHCI controllers.
>> +  Both of them map to one USB2.0 PHY.
>> +  OHCI controller#0 -- usb2phy -- phy#0
>> +  EHCI controller#0 -- usb2phy -- phy#0
>> +
>>  properties:
>>    compatible:
>>      enum:
>> @@ -69,6 +77,7 @@ properties:
>>        - realtek,rtd1395-usb2phy-2port
>>        - realtek,rtd1619-usb2phy
>>        - realtek,rtd1619b-usb2phy
>> +      - realtek,rtl9607-usb2phy
>>  
>>    reg:
>>      items:
>> @@ -130,6 +139,9 @@ properties:
>>      minimum: -8
>>      maximum: 8
>>  
>> +  resets:
>> +    maxItems: 1
>> +
>>  required:
>>    - compatible
>>    - reg
>> @@ -157,6 +169,15 @@ allOf:
>>      then:
>>        properties:
>>          realtek,driving-level-compensate: false
>> +  - if:
>> +      properties:
>> +        compatible:
>> +          contains:
>> +            enum:
>> +              - realtek,rtl9607-usb2phy
>> +    then:
>> +      required:
>> +        - resets
> 
> If it is unclear, they might not have it so,
> 
> else: ... :false

Right, i suppose if RTD SoCs had them they would have been added here already so..
will make the resets false for other devices

> see example-schema.
> 
> Best regards,
> Krzysztof

Thanks,
Rustam

[PATCH 4/6] phy: realtek: usb2: introduce reset controller struct

[Rustam Adilov]

In RTL9607C, there is so called "IP Enable Controller" which resemble
reset controller with reset lines and is used for various things like
USB, PCIE, GMAC and such.

Introduce the reset_control struct to this driver to handle deasserting
usb2 phy reset line.

Make use of the function devm_reset_control_array_get_optional_exclusive()
function to get the reset controller and since existing RTD SoCs don't
specify the resets we can have a cleaner code.

Co-developed-by: Michael Zavertkin <misha.zavertkin@mail.ru>
Signed-off-by: Michael Zavertkin <misha.zavertkin@mail.ru>
Signed-off-by: Rustam Adilov <adilov@disroot.org>
---
 drivers/phy/realtek/phy-rtk-usb2.c | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/drivers/phy/realtek/phy-rtk-usb2.c b/drivers/phy/realtek/phy-rtk-usb2.c
index e65b8525b88b..070cba1e0e0a 100644
--- a/drivers/phy/realtek/phy-rtk-usb2.c
+++ b/drivers/phy/realtek/phy-rtk-usb2.c
@@ -17,6 +17,7 @@
 #include <linux/sys_soc.h>
 #include <linux/mfd/syscon.h>
 #include <linux/phy/phy.h>
+#include <linux/reset.h>
 #include <linux/usb.h>
 
 /* GUSB2PHYACCn register */
@@ -130,6 +131,7 @@ struct rtk_phy {
 	struct phy_cfg *phy_cfg;
 	int num_phy;
 	struct phy_parameter *phy_parameter;
+	struct reset_control *phy_rst;
 
 	struct dentry *debug_dir;
 };
@@ -602,6 +604,10 @@ static int do_rtk_phy_init(struct rtk_phy *rtk_phy, int index)
 	phy_parameter = &((struct phy_parameter *)rtk_phy->phy_parameter)[index];
 	phy_reg = &phy_parameter->phy_reg;
 
+	reset_control_deassert(rtk_phy->phy_rst);
+
+	mdelay(5);
+
 	if (phy_cfg->use_default_parameter) {
 		dev_dbg(rtk_phy->dev, "%s phy#%d use default parameter\n",
 			__func__, index);
@@ -1069,6 +1075,12 @@ static int rtk_usb2phy_probe(struct platform_device *pdev)
 
 	rtk_phy->num_phy = phy_cfg->num_phy;
 
+	rtk_phy->phy_rst = devm_reset_control_array_get_optional_exclusive(dev);
+	if (IS_ERR(rtk_phy->phy_rst)) {
+		dev_err(dev, "usb2 phy resets are not working\n");
+		return PTR_ERR(rtk_phy->phy_rst);
+	}
+
 	ret = parse_phy_data(rtk_phy);
 	if (ret)
 		goto err;
-- 
2.53.0

[PATCH 5/6] phy: realtek: usb2: add support for RTL9607C USB2 PHY

[Rustam Adilov]

Add support for the usb2 phy of RTL9607C series based SoCs.
Add the macros and phy config struct for rtl9607.

RTL9607C requires to clear a "force host disconnect" bit in the
specific register (which is at an offset from reg_wrap_vstatus)
before proceeding with phy parameter writes.

Add the bool variable to the driver data struct and hide this whole
procedure under the if statement that checks this new variable.

Co-developed-by: Michael Zavertkin <misha.zavertkin@mail.ru>
Signed-off-by: Michael Zavertkin <misha.zavertkin@mail.ru>
Signed-off-by: Rustam Adilov <adilov@disroot.org>
---
 drivers/phy/realtek/phy-rtk-usb2.c | 57 ++++++++++++++++++++++++++++++
 1 file changed, 57 insertions(+)

diff --git a/drivers/phy/realtek/phy-rtk-usb2.c b/drivers/phy/realtek/phy-rtk-usb2.c
index 070cba1e0e0a..bf22d12681dc 100644
--- a/drivers/phy/realtek/phy-rtk-usb2.c
+++ b/drivers/phy/realtek/phy-rtk-usb2.c
@@ -26,6 +26,12 @@
 #define PHY_VCTRL_SHIFT 8
 #define PHY_REG_DATA_MASK 0xff
 
+#define PHY_9607_VSTS_BUSY BIT(17)
+#define PHY_9607_NEW_REG_REQ BIT(13)
+
+#define PHY_9607_FORCE_DISCONNECT_REG 0x10
+#define PHY_9607_FORCE_DISCONNECT_BIT BIT(5)
+
 #define GET_LOW_NIBBLE(addr) ((addr) & 0x0f)
 #define GET_HIGH_NIBBLE(addr) (((addr) & 0xf0) >> 4)
 
@@ -109,6 +115,7 @@ struct phy_cfg {
 
 	u32 (*read)(void __iomem *reg);
 	void (*write)(u32 val, void __iomem *reg);
+	bool force_host_disconnect;
 };
 
 struct phy_parameter {
@@ -614,6 +621,16 @@ static int do_rtk_phy_init(struct rtk_phy *rtk_phy, int index)
 		goto do_toggle;
 	}
 
+	if (phy_cfg->force_host_disconnect) {
+		/* disable force-host-disconnect */
+		u32 temp = readl(phy_reg->reg_wrap_vstatus + PHY_9607_FORCE_DISCONNECT_REG);
+
+		temp &= ~PHY_9607_FORCE_DISCONNECT_BIT;
+		writel(temp, phy_reg->reg_wrap_vstatus + PHY_9607_FORCE_DISCONNECT_REG);
+
+		mdelay(10);
+	}
+
 	/* Set page 0 */
 	phy_data_page = phy_cfg->page0;
 	rtk_phy_set_page(phy_reg, 0);
@@ -1141,6 +1158,7 @@ static const struct phy_cfg rtd1295_phy_cfg = {
 	.new_reg_req = PHY_NEW_REG_REQ,
 	.read = phy_read,
 	.write = phy_write,
+	.force_host_disconnect = false,
 };
 
 static const struct phy_cfg rtd1395_phy_cfg = {
@@ -1170,6 +1188,7 @@ static const struct phy_cfg rtd1395_phy_cfg = {
 	.new_reg_req = PHY_NEW_REG_REQ,
 	.read = phy_read,
 	.write = phy_write,
+	.force_host_disconnect = false,
 };
 
 static const struct phy_cfg rtd1395_phy_cfg_2port = {
@@ -1199,6 +1218,7 @@ static const struct phy_cfg rtd1395_phy_cfg_2port = {
 	.new_reg_req = PHY_NEW_REG_REQ,
 	.read = phy_read,
 	.write = phy_write,
+	.force_host_disconnect = false,
 };
 
 static const struct phy_cfg rtd1619_phy_cfg = {
@@ -1226,6 +1246,7 @@ static const struct phy_cfg rtd1619_phy_cfg = {
 	.new_reg_req = PHY_NEW_REG_REQ,
 	.read = phy_read,
 	.write = phy_write,
+	.force_host_disconnect = false,
 };
 
 static const struct phy_cfg rtd1319_phy_cfg = {
@@ -1257,6 +1278,7 @@ static const struct phy_cfg rtd1319_phy_cfg = {
 	.new_reg_req = PHY_NEW_REG_REQ,
 	.read = phy_read,
 	.write = phy_write,
+	.force_host_disconnect = false,
 };
 
 static const struct phy_cfg rtd1312c_phy_cfg = {
@@ -1287,6 +1309,7 @@ static const struct phy_cfg rtd1312c_phy_cfg = {
 	.new_reg_req = PHY_NEW_REG_REQ,
 	.read = phy_read,
 	.write = phy_write,
+	.force_host_disconnect = false,
 };
 
 static const struct phy_cfg rtd1619b_phy_cfg = {
@@ -1317,6 +1340,7 @@ static const struct phy_cfg rtd1619b_phy_cfg = {
 	.new_reg_req = PHY_NEW_REG_REQ,
 	.read = phy_read,
 	.write = phy_write,
+	.force_host_disconnect = false,
 };
 
 static const struct phy_cfg rtd1319d_phy_cfg = {
@@ -1347,6 +1371,7 @@ static const struct phy_cfg rtd1319d_phy_cfg = {
 	.new_reg_req = PHY_NEW_REG_REQ,
 	.read = phy_read,
 	.write = phy_write,
+	.force_host_disconnect = false,
 };
 
 static const struct phy_cfg rtd1315e_phy_cfg = {
@@ -1378,6 +1403,37 @@ static const struct phy_cfg rtd1315e_phy_cfg = {
 	.new_reg_req = PHY_NEW_REG_REQ,
 	.read = phy_read,
 	.write = phy_write,
+	.force_host_disconnect = false,
+};
+
+static const struct phy_cfg rtl9607_phy_cfg = {
+	.page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
+	.page0 = { [0] = {0xe0, 0x95},
+		   [4] = {0xe4, 0x6a},
+		  [12] = {0xf3, 0x31}, },
+	.page1_size = MAX_USB_PHY_PAGE1_DATA_SIZE,
+	.page1 = { [0] = {0xe0, 0x26}, },
+	.page2_size = MAX_USB_PHY_PAGE2_DATA_SIZE,
+	.page2 = { [7] = {0xe7, 0x33}, },
+	.num_phy = 1,
+	.check_efuse = false,
+	.check_efuse_version = CHECK_EFUSE_V2,
+	.efuse_dc_driving_rate = EFUS_USB_DC_CAL_RATE,
+	.dc_driving_mask = 0x1f,
+	.efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
+	.dc_disconnect_mask = 0xf,
+	.usb_dc_disconnect_at_page0 = true,
+	.do_toggle = true,
+	.do_toggle_driving = false,
+	.driving_updated_for_dev_dis = 0x8,
+	.use_default_parameter = false,
+	.is_double_sensitivity_mode = true,
+	.vstatus_offset = 0xc,
+	.vstatus_busy = PHY_9607_VSTS_BUSY,
+	.new_reg_req = PHY_9607_NEW_REG_REQ,
+	.read = phy_read_le,
+	.write = phy_write_le,
+	.force_host_disconnect = true,
 };
 
 static const struct of_device_id usbphy_rtk_dt_match[] = {
@@ -1390,6 +1446,7 @@ static const struct of_device_id usbphy_rtk_dt_match[] = {
 	{ .compatible = "realtek,rtd1395-usb2phy-2port", .data = &rtd1395_phy_cfg_2port },
 	{ .compatible = "realtek,rtd1619-usb2phy", .data = &rtd1619_phy_cfg },
 	{ .compatible = "realtek,rtd1619b-usb2phy", .data = &rtd1619b_phy_cfg },
+	{ .compatible = "realtek,rtl9607-usb2phy", .data = &rtl9607_phy_cfg },
 	{},
 };
 MODULE_DEVICE_TABLE(of, usbphy_rtk_dt_match);
-- 
2.53.0

[PATCH 6/6] phy: realtek: usb2: Make configs available for MACH_REALTEK_RTL

[Rustam Adilov]

Add the MACH_REALTEK_RTL to the if statement to make the config
options available for Realtek RTL SoCs as well.

Signed-off-by: Rustam Adilov <adilov@disroot.org>
---
 drivers/phy/realtek/Kconfig | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/phy/realtek/Kconfig b/drivers/phy/realtek/Kconfig
index 75ac7e7c31ae..f9eadffacd18 100644
--- a/drivers/phy/realtek/Kconfig
+++ b/drivers/phy/realtek/Kconfig
@@ -3,7 +3,7 @@
 # Phy drivers for Realtek platforms
 #
 
-if ARCH_REALTEK || COMPILE_TEST
+if ARCH_REALTEK || MACH_REALTEK_RTL || COMPILE_TEST
 
 config PHY_RTK_RTD_USB2PHY
 	tristate "Realtek RTD USB2 PHY Transceiver Driver"
-- 
2.53.0