Re: [PATCH 2/2] dt-bindings: hwmon: add renesas,isl28022

[Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>]

On 26/07/2023 17:22, Carsten Spieß wrote:
> Add dt-bindings for Renesase ISL28022 power monitor.
> 
> Signed-off-by: Carsten Spieß <mail@carsten-spiess.de>
> ---

Thank you for your patch. There is something to discuss/improve.


>  .../bindings/hwmon/renesas,isl28022.yaml      | 67 +++++++++++++++++++
>  MAINTAINERS                                   |  1 +
>  2 files changed, 68 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/hwmon/renesas,isl28022.yaml
> 
> diff --git a/Documentation/devicetree/bindings/hwmon/renesas,isl28022.yaml b/Documentation/devicetree/bindings/hwmon/renesas,isl28022.yaml
> new file mode 100644
> index 000000000000..5ecf892db269
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/hwmon/renesas,isl28022.yaml
> @@ -0,0 +1,67 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +

No blank line.

> +$id: http://devicetree.org/schemas/hwmon/renesas,isl28022.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Renesas ISL28022 power monitor
> +
> +maintainers:
> +  - Carsten Spieß <mail@carsten-spiess.de>
> +
> +description: |
> +  The ISL28022 is a power monitor with I2C interface. The device monitors
> +  voltage, current via shunt resistor and calculated power.
> +
> +  Datasheets:
> +    https://www.renesas.com/us/en/www/doc/datasheet/isl28022.pdf
> +
> +Required properties:
> +  compatible:
> +    enum:
> +      - renesas,isl28022
> +
> +  reg:
> +    maxItems: 1
> +
> +Optional properties:

It does not look like you tested the bindings, at least after quick
look. Please run `make dt_binding_check` (see
Documentation/devicetree/bindings/writing-schema.rst for instructions).
Maybe you need to update your dtschema and yamllint.

These are "properties"

> +  shunt-resistor-micro-ohms:
> +    description:
> +      Shunt resistor value in micro-Ohm
> +      defaults to <0> when not set
> +      monitoring of current and power not supported when <0>
> +
> +  shunt-gain:

1. Missing vendor prefix (does not look like generic property)
2. -microvolt

> +    description:
> +      Shunt gain to scale maximal shunt voltage to
> +      40mV, 80mV, 160mV, 320mV
> +      defaults to <8> (320mV) when not set

And then enum is for 40, 80, 160 and 320.

> +    enum: [1, 2, 4, 8]
> +
> +  average:
> +    description: |
> +      Number of samples to be used to report voltage, current and power values.
> +      defaults to <0> when not set
> +    enum: [0, 1, 2, 4, 8, 16, 32, 64, 128]

I am sure hwmon has some property for this. Are you sure it is called
"average"?

> +
> +required:
> +  - compatible
> +  - reg
> +
> +additionalProperties: false
> +


Best regards,
Krzysztof