[PATCH v13 0/7] arm64: sunxi: Allwinner H616 SoC DT support

[PATCH v13 0/7] arm64: sunxi: Allwinner H616 SoC DT support

[Andre Przywara]

Hi,

only some minor changes this time in the .dtsi, addressing the comments,
many thanks to Jernej and Samuel for that! Also adding the R-b tags.

This keeps the TF-A reserved memory node, as a compromise for a smoother
user experience.

This is on top of kernel.org's sunxi/dt-for-5.20, to get the new I2C
fallback compatible. The series can be found here:
https://github.com/apritzel/linux/commits/h616-v13

For a complete changelog, see below.

Thanks!
Andre

==================
This series gathers patches to support the Allwinner H616 SoC. This is
a rather uninspired SoC (Quad-A53 with the usual peripherals), but
allows for some cheap development boards and TV boxes, and supports
up to 4GB of DRAM.

Some DT binding patches are sprinkled throughout the series, to add
the new compatible names right before they are used.
Eventually we get the .dtsi for the SoC in patch 3, and the .dts for
the OrangePi Zero2 board[1] later, followed by the .dts for the X96 Mate
TV box[2] afterwards.

U-Boot and Trusted Firmware support is now merged in released versions,
it allows booting via FEL or SD card, also you can TFTP kernels in on
the OrangePi Zero 2 board.

Many thanks to Jernej for his tremendous help on this, also for the
awesome input and help from the #linux-sunxi IRC channel.

The whole series (including the prerequisites) can also be found here:
https://github.com/apritzel/linux/commits/h616-v13

Happy reviewing!

Cheers,
Andre

[1] https://linux-sunxi.org/Orange_Pi_Zero_2
[2] https://linux-sunxi.org/X96_Mate

Changelog v12 .. v13:
- Gather Reviewed-by: and Acked-by: tags
- Use symbolic names for RTC clock specifiers
- Use new V536 I2C fallback compatible
- Add /omit-if-no-ref/ for R_I2C pins
- Reorder EMAC properties
- Drop redundant RTC clock output names
- Drop address specifier from soc node name
- Amend TF-A reserved memory node to match current TF-A usage (+comment)
- Adjust CPU and GPU voltage regulator range

Changelog v11 .. v12:
- Add EMAC compatible string to DT bindings
- Make pinctrl interrupts optional in the DT bindings
- Allow a vcc-pi-supply in the pinctrl DT bindings
- Fix RTC interrupt number in the .dtsi
- Add vcc-px-supply properties to the OrangePi Zero 2 DT
- Add /omit-if-no-ref/ to rarely used pinctrl subnodes
- Drop fixed pinctrl properties from the SPI nodes in the .dtsi
- Split off CS0 pin from the SPI0 pins
- Remove bogus interrupt properties from the R_PIO DT node
- Make DCDC-E regulator always-on

Changelog v10 .. v11:
- Drop already merged RTC patches
- Drop USB patches
- Also add RTC gate clock to the H6, but mark it as unused
- Add X96 Mate manufacturer to vendor list

Changelog v9 .. v10:
- based on ccu-sun6i-rtc clock driver
- add RTC bus clock and 32k system PLL clock
- drop clock related code from actual RTC driver (just use RTC bits)
- .dtsi: remove redundant status = "okay"; from .dtsi
- .dts: drop #address-cells = <0> from IRQ controller nodes
- .dtsi: fix indentation of IR node
- .dtsi: adjust RTC node to new binding
- re-add USB patches

Changelog v8 .. v9:
- RTC: Rely on the division to split of the H:M:S part from the day part
- Add Jernej's Review tags

Changelog v7 .. v8:
- Rebase on top of 5.14-rc1, which already includes the previous v7 02/19
- Drop USB and Ethernet patches (to keep series small)
- Use "clocks: false" in RTC DT binding (2/11)
- Include fix for RTC overflow check (3/11)
- Use div_64() to avoid linking error on some 32-bit platforms (4+5/11)
- Adjust to changed RTC overflow check (5/11)
- Drop USB nodes from .dtsi file
- Move mmc-ddr-1_8v property from .dtsi file into board .dts
- Fix DTC warnings (underscore in node name, soc@0, #a-c in IRQ controllers)

Changelog v6 .. v7:
- Fix AXP305 binding documentation blunder (01/19)
- Improve new linear day support (use existing conversion functions) (04/19)
- Add support for changed RTC alarm registers (05/19)
- Add support for RTCs without a LOSC clock (06/19)
- Rework USB PHY2 SIDDQ quirk to use PHY clocks directly (14/19)
- Add X96 Mate compatible string to binding doc (17/19)
- Add Rob's ACKs

Changelog v5 .. v6:
- Drop already merged clock, pinctrl and MMC support from this series
- Properly fix AXP support by skipping power key initialisation
- Add patch to support new RTC date storage encoding
- Re-add USB HCI PHY refactoring
- Add patch to allow USB reset line sharing
- Add patch to introduce quirk for PHY2 SIDDQ clearing
- Re-add USB nodes to the .dtsi
- Add USB gadget support
- Add DT for X96 Mate TV box

Changelog v4 .. v5:
- Fix CCU binding to pass dtbs_check
- Add RSB compatible string to binding doc
- Rename IR pin name to pass dtbs_check
- Add EMAC compatible string to binding doc
- Drop USB PHY support and binding doc patches 
- Drop USB nodes from .dtsi and .dts
- Drop second EMAC node from .dtsi

Changelog v3 .. v4:
- Drop MMC and pinctrl matches (already in some -next trees)
- Add Maxime's Acks
- Add patch to update the AXP MFD DT bindings
- Add new patch (05/21) to fix axp20x-pek driver
- Change AXP IRQ fix to check for invalid IRQ line number
- Split joint DT bindings patch (v3 18/21) into subsystems
- move dwmac variable to keep christmas tree
- Use enums for USB PHY compatible strings in DT binding
- Enable watchdog (briefly verified to work)
- Add PHY2 to HCI1&3, this fixes USB
- limit r-ccu register frame length to not collide with NMI controller
- add interrupt-controller property to AXP DT node

Changelog v2 .. v3:
- Add Rob's Acks
- Drop redundant maxItems from pinctrl DT binding
- Rename h_i2s* to just i2s* in pinctrl names
- Use more declarative i2s0_d{in,out}{0,1} names
- Add RSB pins to pinctrl
- Include RSB clocks (sharing with newly added H6 versions)
- Fix CEC clock (add 2nd enable bit, also fix predivider flag)
- Rename PMU_UNK1 register in USB PHY
- Add USB and MUSB DT binding patches
- Add MMC/SD speed modes to .dtsi

Changelog v1 .. v2:
- pinctrl: adjust irq bank map to cover undocumented GPIO bank IRQs
- use differing h_i2s0 pin output names
- r-ccu: fix number of used clocks
- ccu: remove PLL-PERIPHy(4X)
- ccu: fix gpu1 divider range
- ccu: fix usb-phy3 parent
- ccu: add missing TV clocks
- ccu: rework to CLK_OF_DECLARE style
- ccu: enable output bit for PLL clocks
- ccu: renumber clocks
- .dtsi: drop sun50i-a64-system-control fallback
- .dtsi: drop unknown SRAM regions
- .dtsi: add more (undocumented) GPIO interrupts
- .dtsi: fix I2C3 pin names
- .dtsi: use a100-emmc fallback for MMC2
- .dtsi: add second EMAC controller
- .dtsi: use H3 MUSB controller fallback
- .dtsi: fix frame size for USB PHY PMU registers
- .dtsi: add USB0 PHY references
- .dtsi: fix IR controller clock source
- .dts: fix LED naming and swap pins
- .dts: use 5V supply parent for USB supply
- .dts: drop dummy IRQ for AXP
- .dts: enable 3V3 header pin power rail
- .dts: add SPI flash node
- .dts: make USB-C port peripheral only
- add IRQ-less AXP support
- add two patches to support more than one EMAC clock
- add patch to rework and extend USB PHY support
- add DT binding documentation patches

Andre Przywara (7):
  dt-bindings: arm: sunxi: Add H616 EMAC compatible
  dt-bindings: pinctrl: sunxi: Make interrupts optional
  arm64: dts: allwinner: Add Allwinner H616 .dtsi file
  dt-bindings: pinctrl: sunxi: allow vcc-pi-supply
  dt-bindings: arm: sunxi: Add two H616 board compatible strings
  arm64: dts: allwinner: h616: Add OrangePi Zero 2 board support
  arm64: dts: allwinner: h616: Add X96 Mate TV box support

 .../devicetree/bindings/arm/sunxi.yaml        |  10 +
 .../net/allwinner,sun8i-a83t-emac.yaml        |   1 +
 .../pinctrl/allwinner,sun4i-a10-pinctrl.yaml  |  18 +-
 .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
 arch/arm64/boot/dts/allwinner/Makefile        |   2 +
 .../allwinner/sun50i-h616-orangepi-zero2.dts  | 213 +++++++
 .../dts/allwinner/sun50i-h616-x96-mate.dts    | 177 ++++++
 .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 591 ++++++++++++++++++
 8 files changed, 1010 insertions(+), 4 deletions(-)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi

-- 
2.25.1

[PATCH v13 1/7] dt-bindings: arm: sunxi: Add H616 EMAC compatible

[Andre Przywara]

The Allwinner H616 contains an "EMAC" Ethernet MAC compatible to the A64
version.

Add it to the list of compatible strings.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 .../devicetree/bindings/net/allwinner,sun8i-a83t-emac.yaml       | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/net/allwinner,sun8i-a83t-emac.yaml b/Documentation/devicetree/bindings/net/allwinner,sun8i-a83t-emac.yaml
index 6a4831fd3616c..87f1306831cc9 100644
--- a/Documentation/devicetree/bindings/net/allwinner,sun8i-a83t-emac.yaml
+++ b/Documentation/devicetree/bindings/net/allwinner,sun8i-a83t-emac.yaml
@@ -22,6 +22,7 @@ properties:
           - enum:
               - allwinner,sun20i-d1-emac
               - allwinner,sun50i-h6-emac
+              - allwinner,sun50i-h616-emac
           - const: allwinner,sun50i-a64-emac
 
   reg:
-- 
2.25.1

[PATCH v13 2/7] dt-bindings: pinctrl: sunxi: Make interrupts optional

[Andre Przywara]

The R_PIO pinctrl device on the Allwinner H616 SoC does not have an
interrupt (it features only two pins).
However the binding requires at least naming one upstream interrupt,
plus the #interrupt-cells and interrupt-controller properties.

Drop the unconditional requirement for the interrupt properties, and
make them dependent on being not this particular pinctrl device.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Samuel Holland <samuel@sholland.org>
---
 .../pinctrl/allwinner,sun4i-a10-pinctrl.yaml     | 16 +++++++++++++---
 1 file changed, 13 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
index bfce850c20351..360dcd757e9da 100644
--- a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
@@ -133,14 +133,11 @@ patternProperties:
 
 required:
   - "#gpio-cells"
-  - "#interrupt-cells"
   - compatible
   - reg
-  - interrupts
   - clocks
   - clock-names
   - gpio-controller
-  - interrupt-controller
 
 allOf:
   # FIXME: We should have the pin bank supplies here, but not a lot of
@@ -148,6 +145,19 @@ allOf:
   # warnings.
 
   - $ref: "pinctrl.yaml#"
+  - if:
+      not:
+        properties:
+          compatible:
+            enum:
+              - allwinner,sun50i-h616-r-pinctrl
+
+    then:
+      required:
+        - "#interrupt-cells"
+        - interrupts
+        - interrupt-controller
+
   - if:
       properties:
         compatible:
-- 
2.25.1

[PATCH v13 3/7] arm64: dts: allwinner: Add Allwinner H616 .dtsi file

[Andre Przywara]

This (relatively) new SoC is similar to the H6, but drops the (broken)
PCIe support and the USB 3.0 controller. It also gets the management
controller removed, which in turn removes *some*, but not all of the
devices formerly dedicated to the ARISC (CPUS).
And while there is still the extra sunxi interrupt controller, the
package lacks the corresponding NMI pin, so no interrupts for the PMIC.

The reserved memory node is actually handled by Trusted Firmware now,
but U-Boot fails to propagate this to a separately loaded DTB, so we
keep it in here for now, until U-Boot learns to do this properly.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 591 ++++++++++++++++++
 1 file changed, 591 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
new file mode 100644
index 0000000000000..8a81baf7de249
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
@@ -0,0 +1,591 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2020 Arm Ltd.
+// based on the H6 dtsi, which is:
+//   Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/sun50i-h616-ccu.h>
+#include <dt-bindings/clock/sun50i-h6-r-ccu.h>
+#include <dt-bindings/clock/sun6i-rtc.h>
+#include <dt-bindings/reset/sun50i-h616-ccu.h>
+#include <dt-bindings/reset/sun50i-h6-r-ccu.h>
+
+/ {
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <0>;
+			enable-method = "psci";
+			clocks = <&ccu CLK_CPUX>;
+		};
+
+		cpu1: cpu@1 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <1>;
+			enable-method = "psci";
+			clocks = <&ccu CLK_CPUX>;
+		};
+
+		cpu2: cpu@2 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <2>;
+			enable-method = "psci";
+			clocks = <&ccu CLK_CPUX>;
+		};
+
+		cpu3: cpu@3 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <3>;
+			enable-method = "psci";
+			clocks = <&ccu CLK_CPUX>;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/*
+		 * 256 KiB reserved for Trusted Firmware-A (BL31).
+		 * This is added by BL31 itself, but some bootloaders fail
+		 * to propagate this into the DTB handed to kernels.
+		 */
+		secmon@40000000 {
+			reg = <0x0 0x40000000 0x0 0x40000>;
+			no-map;
+		};
+	};
+
+	osc24M: osc24M-clk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		clock-output-names = "osc24M";
+	};
+
+	pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		arm,no-tick-in-suspend;
+		interrupts = <GIC_PPI 13
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 14
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 11
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 10
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x0 0x40000000>;
+
+		syscon: syscon@3000000 {
+			compatible = "allwinner,sun50i-h616-system-control";
+			reg = <0x03000000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			sram_c: sram@28000 {
+				compatible = "mmio-sram";
+				reg = <0x00028000 0x30000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x00028000 0x30000>;
+			};
+		};
+
+		ccu: clock@3001000 {
+			compatible = "allwinner,sun50i-h616-ccu";
+			reg = <0x03001000 0x1000>;
+			clocks = <&osc24M>, <&rtc CLK_OSC32K>, <&rtc CLK_IOSC>;
+			clock-names = "hosc", "losc", "iosc";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		watchdog: watchdog@30090a0 {
+			compatible = "allwinner,sun50i-h616-wdt",
+				     "allwinner,sun6i-a31-wdt";
+			reg = <0x030090a0 0x20>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc24M>;
+		};
+
+		pio: pinctrl@300b000 {
+			compatible = "allwinner,sun50i-h616-pinctrl";
+			reg = <0x0300b000 0x400>;
+			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_APB1>, <&osc24M>, <&rtc CLK_OSC32K>;
+			clock-names = "apb", "hosc", "losc";
+			gpio-controller;
+			#gpio-cells = <3>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+
+			ext_rgmii_pins: rgmii-pins {
+				pins = "PI0", "PI1", "PI2", "PI3", "PI4",
+				       "PI5", "PI7", "PI8", "PI9", "PI10",
+				       "PI11", "PI12", "PI13", "PI14", "PI15",
+				       "PI16";
+				function = "emac0";
+				drive-strength = <40>;
+			};
+
+			i2c0_pins: i2c0-pins {
+				pins = "PI6", "PI7";
+				function = "i2c0";
+			};
+
+			i2c3_ph_pins: i2c3-ph-pins {
+				pins = "PH4", "PH5";
+				function = "i2c3";
+			};
+
+			ir_rx_pin: ir-rx-pin {
+				pins = "PH10";
+				function = "ir_rx";
+			};
+
+			mmc0_pins: mmc0-pins {
+				pins = "PF0", "PF1", "PF2", "PF3",
+				       "PF4", "PF5";
+				function = "mmc0";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			/omit-if-no-ref/
+			mmc1_pins: mmc1-pins {
+				pins = "PG0", "PG1", "PG2", "PG3",
+				       "PG4", "PG5";
+				function = "mmc1";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			mmc2_pins: mmc2-pins {
+				pins = "PC0", "PC1", "PC5", "PC6",
+				       "PC8", "PC9", "PC10", "PC11",
+				       "PC13", "PC14", "PC15", "PC16";
+				function = "mmc2";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			/omit-if-no-ref/
+			spi0_pins: spi0-pins {
+				pins = "PC0", "PC2", "PC4";
+				function = "spi0";
+			};
+
+			/omit-if-no-ref/
+			spi0_cs0_pin: spi0-cs0-pin {
+				pins = "PC3";
+				function = "spi0";
+			};
+
+			/omit-if-no-ref/
+			spi1_pins: spi1-pins {
+				pins = "PH6", "PH7", "PH8";
+				function = "spi1";
+			};
+
+			/omit-if-no-ref/
+			spi1_cs0_pin: spi1-cs0-pin {
+				pins = "PH5";
+				function = "spi1";
+			};
+
+			uart0_ph_pins: uart0-ph-pins {
+				pins = "PH0", "PH1";
+				function = "uart0";
+			};
+
+			/omit-if-no-ref/
+			uart1_pins: uart1-pins {
+				pins = "PG6", "PG7";
+				function = "uart1";
+			};
+
+			/omit-if-no-ref/
+			uart1_rts_cts_pins: uart1-rts-cts-pins {
+				pins = "PG8", "PG9";
+				function = "uart1";
+			};
+		};
+
+		gic: interrupt-controller@3021000 {
+			compatible = "arm,gic-400";
+			reg = <0x03021000 0x1000>,
+			      <0x03022000 0x2000>,
+			      <0x03024000 0x2000>,
+			      <0x03026000 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+		};
+
+		mmc0: mmc@4020000 {
+			compatible = "allwinner,sun50i-h616-mmc",
+				     "allwinner,sun50i-a100-mmc";
+			reg = <0x04020000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC0>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc0_pins>;
+			status = "disabled";
+			max-frequency = <150000000>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			mmc-ddr-3_3v;
+			cap-sdio-irq;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc1: mmc@4021000 {
+			compatible = "allwinner,sun50i-h616-mmc",
+				     "allwinner,sun50i-a100-mmc";
+			reg = <0x04021000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC1>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc1_pins>;
+			status = "disabled";
+			max-frequency = <150000000>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			mmc-ddr-3_3v;
+			cap-sdio-irq;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc2: mmc@4022000 {
+			compatible = "allwinner,sun50i-h616-emmc",
+				     "allwinner,sun50i-a100-emmc";
+			reg = <0x04022000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC2>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc2_pins>;
+			status = "disabled";
+			max-frequency = <150000000>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			mmc-ddr-3_3v;
+			cap-sdio-irq;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		uart0: serial@5000000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000000 0x400>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART0>;
+			resets = <&ccu RST_BUS_UART0>;
+			status = "disabled";
+		};
+
+		uart1: serial@5000400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000400 0x400>;
+			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART1>;
+			resets = <&ccu RST_BUS_UART1>;
+			status = "disabled";
+		};
+
+		uart2: serial@5000800 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000800 0x400>;
+			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART2>;
+			resets = <&ccu RST_BUS_UART2>;
+			status = "disabled";
+		};
+
+		uart3: serial@5000c00 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000c00 0x400>;
+			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART3>;
+			resets = <&ccu RST_BUS_UART3>;
+			status = "disabled";
+		};
+
+		uart4: serial@5001000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05001000 0x400>;
+			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART4>;
+			resets = <&ccu RST_BUS_UART4>;
+			status = "disabled";
+		};
+
+		uart5: serial@5001400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05001400 0x400>;
+			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART5>;
+			resets = <&ccu RST_BUS_UART5>;
+			status = "disabled";
+		};
+
+		i2c0: i2c@5002000 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun8i-v536-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002000 0x400>;
+			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C0>;
+			resets = <&ccu RST_BUS_I2C0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c0_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c1: i2c@5002400 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun8i-v536-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002400 0x400>;
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C1>;
+			resets = <&ccu RST_BUS_I2C1>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c2: i2c@5002800 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun8i-v536-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002800 0x400>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C2>;
+			resets = <&ccu RST_BUS_I2C2>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c3: i2c@5002c00 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun8i-v536-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002c00 0x400>;
+			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C3>;
+			resets = <&ccu RST_BUS_I2C3>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c4: i2c@5003000 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun8i-v536-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05003000 0x400>;
+			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C4>;
+			resets = <&ccu RST_BUS_I2C4>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		spi0: spi@5010000 {
+			compatible = "allwinner,sun50i-h616-spi",
+				     "allwinner,sun8i-h3-spi";
+			reg = <0x05010000 0x1000>;
+			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
+			clock-names = "ahb", "mod";
+			resets = <&ccu RST_BUS_SPI0>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		spi1: spi@5011000 {
+			compatible = "allwinner,sun50i-h616-spi",
+				     "allwinner,sun8i-h3-spi";
+			reg = <0x05011000 0x1000>;
+			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
+			clock-names = "ahb", "mod";
+			resets = <&ccu RST_BUS_SPI1>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		emac0: ethernet@5020000 {
+			compatible = "allwinner,sun50i-h616-emac",
+				     "allwinner,sun50i-a64-emac";
+			reg = <0x05020000 0x10000>;
+			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			clocks = <&ccu CLK_BUS_EMAC0>;
+			clock-names = "stmmaceth";
+			resets = <&ccu RST_BUS_EMAC0>;
+			reset-names = "stmmaceth";
+			syscon = <&syscon>;
+			status = "disabled";
+
+			mdio0: mdio {
+				compatible = "snps,dwmac-mdio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		rtc: rtc@7000000 {
+			compatible = "allwinner,sun50i-h616-rtc";
+			reg = <0x07000000 0x400>;
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&r_ccu CLK_R_APB1_RTC>, <&osc24M>,
+				 <&ccu CLK_PLL_SYSTEM_32K>;
+			clock-names = "bus", "hosc",
+				      "pll-32k";
+			#clock-cells = <1>;
+		};
+
+		r_ccu: clock@7010000 {
+			compatible = "allwinner,sun50i-h616-r-ccu";
+			reg = <0x07010000 0x210>;
+			clocks = <&osc24M>, <&rtc CLK_OSC32K>, <&rtc CLK_IOSC>,
+				 <&ccu CLK_PLL_PERIPH0>;
+			clock-names = "hosc", "losc", "iosc", "pll-periph";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		r_pio: pinctrl@7022000 {
+			compatible = "allwinner,sun50i-h616-r-pinctrl";
+			reg = <0x07022000 0x400>;
+			clocks = <&r_ccu CLK_R_APB1>, <&osc24M>,
+				 <&rtc CLK_OSC32K>;
+			clock-names = "apb", "hosc", "losc";
+			gpio-controller;
+			#gpio-cells = <3>;
+
+			/omit-if-no-ref/
+			r_i2c_pins: r-i2c-pins {
+				pins = "PL0", "PL1";
+				function = "s_i2c";
+			};
+
+			r_rsb_pins: r-rsb-pins {
+				pins = "PL0", "PL1";
+				function = "s_rsb";
+			};
+		};
+
+		ir: ir@7040000 {
+			compatible = "allwinner,sun50i-h616-ir",
+				     "allwinner,sun6i-a31-ir";
+			reg = <0x07040000 0x400>;
+			interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&r_ccu CLK_R_APB1_IR>,
+				 <&r_ccu CLK_IR>;
+			clock-names = "apb", "ir";
+			resets = <&r_ccu RST_R_APB1_IR>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&ir_rx_pin>;
+			status = "disabled";
+		};
+
+		r_i2c: i2c@7081400 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun8i-v536-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x07081400 0x400>;
+			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&r_ccu CLK_R_APB2_I2C>;
+			resets = <&r_ccu RST_R_APB2_I2C>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		r_rsb: rsb@7083000 {
+			compatible = "allwinner,sun50i-h616-rsb",
+				     "allwinner,sun8i-a23-rsb";
+			reg = <0x07083000 0x400>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&r_ccu CLK_R_APB2_RSB>;
+			clock-frequency = <3000000>;
+			resets = <&r_ccu RST_R_APB2_RSB>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&r_rsb_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
-- 
2.25.1

[PATCH v13 4/7] dt-bindings: pinctrl: sunxi: allow vcc-pi-supply

[Andre Przywara]

The Allwinner H616 SoC contains a VCC_PI pin, which supplies the voltage
for GPIO port I.
Extend the range of supply port names to include vcc-pi-supply to cover
that.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Samuel Holland <samuel@sholland.org>
---
 .../bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml           | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
index 360dcd757e9da..0681b9a3965f0 100644
--- a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
@@ -127,7 +127,7 @@ patternProperties:
 
     additionalProperties: false
 
-  "^vcc-p[a-hlm]-supply$":
+  "^vcc-p[a-ilm]-supply$":
     description:
       Power supplies for pin banks.
 
-- 
2.25.1

[PATCH v13 5/7] dt-bindings: arm: sunxi: Add two H616 board compatible strings

[Andre Przywara]

This adds the two board compatible strings of two boards with the
Allwinner H616 SoC. One is a development board from OrangePi, the other
some TV box from some formerly unused vendor. Add that vendor to the
vendor list on the way.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/arm/sunxi.yaml       | 10 ++++++++++
 Documentation/devicetree/bindings/vendor-prefixes.yaml |  2 ++
 2 files changed, 12 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml
index 95278a6a9a8ec..0c2356778208a 100644
--- a/Documentation/devicetree/bindings/arm/sunxi.yaml
+++ b/Documentation/devicetree/bindings/arm/sunxi.yaml
@@ -863,6 +863,11 @@ properties:
           - const: yones-toptech,bs1078-v2
           - const: allwinner,sun6i-a31s
 
+      - description: X96 Mate TV box
+        items:
+          - const: hechuang,x96-mate
+          - const: allwinner,sun50i-h616
+
       - description: Xunlong OrangePi
         items:
           - const: xunlong,orangepi
@@ -963,4 +968,9 @@ properties:
           - const: xunlong,orangepi-zero-plus2-h3
           - const: allwinner,sun8i-h3
 
+      - description: Xunlong OrangePi Zero 2
+        items:
+          - const: xunlong,orangepi-zero2
+          - const: allwinner,sun50i-h616
+
 additionalProperties: true
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 6bb20b4554d7e..628ca77949c73 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -507,6 +507,8 @@ patternProperties:
     description: Haoyu Microelectronic Co. Ltd.
   "^hardkernel,.*":
     description: Hardkernel Co., Ltd
+  "^hechuang,.*":
+    description: Shenzhen Hechuang Intelligent Co.
   "^hideep,.*":
     description: HiDeep Inc.
   "^himax,.*":
-- 
2.25.1

[PATCH v13 6/7] arm64: dts: allwinner: h616: Add OrangePi Zero 2 board support

[Andre Przywara]

The OrangePi Zero 2 is a development board with the new H616 SoC. It
comes with the following features:
  - Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
  - 512MiB/1GiB DDR3 DRAM
  - AXP305 PMIC
  - Raspberry-Pi-1 compatible GPIO header
  - extra 13 pin expansion header, exposing pins for 2x USB 2.0 ports
  - 1 USB 2.0 host port
  - 1 USB 2.0 type C port (power supply + OTG)
  - MicroSD slot
  - on-board 2MiB bootable SPI NOR flash
  - 1Gbps Ethernet port (via RTL8211F PHY)
  - micro-HDMI port
  - (yet) unsupported Allwinner WiFi/BT chip

Add the devicetree file describing the currently supported features.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../allwinner/sun50i-h616-orangepi-zero2.dts  | 213 ++++++++++++++++++
 2 files changed, 214 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 8fa5c060a4fef..df2214e6d946a 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -38,3 +38,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6-mini.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
new file mode 100644
index 0000000000000..02893f3ac99d4
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
@@ -0,0 +1,213 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2020 Arm Ltd.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "OrangePi Zero2";
+	compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616";
+
+	aliases {
+		ethernet0 = &emac0;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */
+			default-state = "on";
+		};
+
+		led-1 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */
+		};
+	};
+
+	reg_vcc5v: vcc5v {
+		/* board wide 5V supply directly from the USB-C socket */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+};
+
+&emac0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ext_rgmii_pins>;
+	phy-mode = "rgmii";
+	phy-handle = <&ext_rgmii_phy>;
+	phy-supply = <&reg_dcdce>;
+	allwinner,rx-delay-ps = <3100>;
+	allwinner,tx-delay-ps = <700>;
+	status = "okay";
+};
+
+&mdio0 {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_dcdce>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;	/* PF6 */
+	bus-width = <4>;
+	status = "okay";
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp305: pmic@745 {
+		compatible = "x-powers,axp305", "x-powers,axp805",
+			     "x-powers,axp806";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		reg = <0x745>;
+
+		x-powers,self-working-mode;
+		vina-supply = <&reg_vcc5v>;
+		vinb-supply = <&reg_vcc5v>;
+		vinc-supply = <&reg_vcc5v>;
+		vind-supply = <&reg_vcc5v>;
+		vine-supply = <&reg_vcc5v>;
+		aldoin-supply = <&reg_vcc5v>;
+		bldoin-supply = <&reg_vcc5v>;
+		cldoin-supply = <&reg_vcc5v>;
+
+		regulators {
+			reg_aldo1: aldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-sys";
+			};
+
+			reg_aldo2: aldo2 {	/* 3.3V on headers */
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3-ext";
+			};
+
+			reg_aldo3: aldo3 {	/* 3.3V on headers */
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3-ext2";
+			};
+
+			reg_bldo1: bldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc1v8";
+			};
+
+			bldo2 {
+				/* unused */
+			};
+
+			bldo3 {
+				/* unused */
+			};
+
+			bldo4 {
+				/* unused */
+			};
+
+			cldo1 {
+				/* reserved */
+			};
+
+			cldo2 {
+				/* unused */
+			};
+
+			cldo3 {
+				/* unused */
+			};
+
+			reg_dcdca: dcdca {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-cpu";
+			};
+
+			reg_dcdcc: dcdcc {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <990000>;
+				regulator-name = "vdd-gpu-sys";
+			};
+
+			reg_dcdcd: dcdcd {
+				regulator-always-on;
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-name = "vdd-dram";
+			};
+
+			reg_dcdce: dcdce {
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-eth-mmc";
+			};
+
+			sw {
+				/* unused */
+			};
+		};
+	};
+};
+
+&pio {
+	vcc-pc-supply = <&reg_aldo1>;
+	vcc-pf-supply = <&reg_aldo1>;
+	vcc-pg-supply = <&reg_bldo1>;
+	vcc-ph-supply = <&reg_aldo1>;
+	vcc-pi-supply = <&reg_aldo1>;
+};
+
+&spi0  {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins>, <&spi0_cs0_pin>;
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ph_pins>;
+	status = "okay";
+};
-- 
2.25.1

[PATCH v13 7/7] arm64: dts: allwinner: h616: Add X96 Mate TV box support

[Andre Przywara]

The X96 Mate is an Allwinner H616 based TV box, featuring:
  - Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
  - 2GiB/4GiB RAM (fully usable!)
  - 16/32/64GiB eMMC
  - 100Mbps Ethernet (via embedded AC200 EPHY, not yet supported)
  - Unsupported Allwinner WiFi chip
  - 2 x USB 2.0 host ports
  - HDMI port
  - IR receiver
  - 5V/2A DC power supply via barrel plug

Add a basic devicetree for it, with SD card and eMMC working, as
well as serial and the essential peripherals, like the AXP PMIC.

This DT is somewhat minimal, and should work on many other similar TV
boxes with the Allwinner H616 chip.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
---
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../dts/allwinner/sun50i-h616-x96-mate.dts    | 177 ++++++++++++++++++
 2 files changed, 178 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts

diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index df2214e6d946a..6a96494a2e0a3 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -39,3 +39,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6-mini.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts
new file mode 100644
index 0000000000000..6619db34714a4
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts
@@ -0,0 +1,177 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2021 Arm Ltd.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	model = "X96 Mate";
+	compatible = "hechuang,x96-mate", "allwinner,sun50i-h616";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_vcc5v: vcc5v {
+		/* board wide 5V supply directly from the DC input */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+};
+
+&ir {
+	status = "okay";
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_dcdce>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;	/* PF6 */
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc2 {
+	vmmc-supply = <&reg_dcdce>;
+	vqmmc-supply = <&reg_bldo1>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	status = "okay";
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp305: pmic@745 {
+		compatible = "x-powers,axp305", "x-powers,axp805",
+			     "x-powers,axp806";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		reg = <0x745>;
+
+		x-powers,self-working-mode;
+		vina-supply = <&reg_vcc5v>;
+		vinb-supply = <&reg_vcc5v>;
+		vinc-supply = <&reg_vcc5v>;
+		vind-supply = <&reg_vcc5v>;
+		vine-supply = <&reg_vcc5v>;
+		aldoin-supply = <&reg_vcc5v>;
+		bldoin-supply = <&reg_vcc5v>;
+		cldoin-supply = <&reg_vcc5v>;
+
+		regulators {
+			reg_aldo1: aldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-sys";
+			};
+
+			/* Enabled by the Android BSP */
+			reg_aldo2: aldo2 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3-ext";
+				status = "disabled";
+			};
+
+			/* Enabled by the Android BSP */
+			reg_aldo3: aldo3 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3-ext2";
+				status = "disabled";
+			};
+
+			reg_bldo1: bldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc1v8";
+			};
+
+			/* Enabled by the Android BSP */
+			reg_bldo2: bldo2 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc1v8-2";
+				status = "disabled";
+			};
+
+			bldo3 {
+				/* unused */
+			};
+
+			bldo4 {
+				/* unused */
+			};
+
+			cldo1 {
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
+				regulator-name = "vcc2v5";
+			};
+
+			cldo2 {
+				/* unused */
+			};
+
+			cldo3 {
+				/* unused */
+			};
+
+			reg_dcdca: dcdca {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-cpu";
+			};
+
+			reg_dcdcc: dcdcc {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <990000>;
+				regulator-name = "vdd-gpu-sys";
+			};
+
+			reg_dcdcd: dcdcd {
+				regulator-always-on;
+				regulator-min-microvolt = <1360000>;
+				regulator-max-microvolt = <1360000>;
+				regulator-name = "vdd-dram";
+			};
+
+			reg_dcdce: dcdce {
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-eth-mmc";
+			};
+
+			sw {
+				/* unused */
+			};
+		};
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ph_pins>;
+	status = "okay";
+};
-- 
2.25.1

Re: [PATCH v13 1/7] dt-bindings: arm: sunxi: Add H616 EMAC compatible

[Samuel Holland]

Hi Andre,

On 7/8/22 5:52 AM, Andre Przywara wrote:
> The Allwinner H616 contains an "EMAC" Ethernet MAC compatible to the A64
> version.

H616 contains two EMACs, and only EMAC0 is compatible to the A64 version. EMAC1
requires an updated driver that knows about the different syscon register
location. So the new compatible string should be limited to EMAC0, i.e.
allwinner,sun50i-h616-emac0.

Regards,
Samuel

> Add it to the list of compatible strings.
> 
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> Acked-by: Rob Herring <robh@kernel.org>
> ---
>  .../devicetree/bindings/net/allwinner,sun8i-a83t-emac.yaml       | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/Documentation/devicetree/bindings/net/allwinner,sun8i-a83t-emac.yaml b/Documentation/devicetree/bindings/net/allwinner,sun8i-a83t-emac.yaml
> index 6a4831fd3616c..87f1306831cc9 100644
> --- a/Documentation/devicetree/bindings/net/allwinner,sun8i-a83t-emac.yaml
> +++ b/Documentation/devicetree/bindings/net/allwinner,sun8i-a83t-emac.yaml
> @@ -22,6 +22,7 @@ properties:
>            - enum:
>                - allwinner,sun20i-d1-emac
>                - allwinner,sun50i-h6-emac
> +              - allwinner,sun50i-h616-emac
>            - const: allwinner,sun50i-a64-emac
>  
>    reg:
> 

Re: [PATCH v13 3/7] arm64: dts: allwinner: Add Allwinner H616 .dtsi file

[Samuel Holland]

On 7/8/22 5:52 AM, Andre Przywara wrote:
> This (relatively) new SoC is similar to the H6, but drops the (broken)
> PCIe support and the USB 3.0 controller. It also gets the management
> controller removed, which in turn removes *some*, but not all of the
> devices formerly dedicated to the ARISC (CPUS).
> And while there is still the extra sunxi interrupt controller, the
> package lacks the corresponding NMI pin, so no interrupts for the PMIC.
> 
> The reserved memory node is actually handled by Trusted Firmware now,
> but U-Boot fails to propagate this to a separately loaded DTB, so we
> keep it in here for now, until U-Boot learns to do this properly.
> 
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Thanks Andre for persisting with this series!

Other than the EMAC0 compatible string, which will need to change along with the
binding:

Reviewed-by: Samuel Holland <samuel@sholland.org>

Re: [PATCH v13 6/7] arm64: dts: allwinner: h616: Add OrangePi Zero 2 board support

[Samuel Holland]

On 7/8/22 5:52 AM, Andre Przywara wrote:
> The OrangePi Zero 2 is a development board with the new H616 SoC. It
> comes with the following features:
>   - Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
>   - 512MiB/1GiB DDR3 DRAM
>   - AXP305 PMIC
>   - Raspberry-Pi-1 compatible GPIO header
>   - extra 13 pin expansion header, exposing pins for 2x USB 2.0 ports
>   - 1 USB 2.0 host port
>   - 1 USB 2.0 type C port (power supply + OTG)
>   - MicroSD slot
>   - on-board 2MiB bootable SPI NOR flash
>   - 1Gbps Ethernet port (via RTL8211F PHY)
>   - micro-HDMI port
>   - (yet) unsupported Allwinner WiFi/BT chip
> 
> Add the devicetree file describing the currently supported features.
> 
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>

Acked-by: Samuel Holland <samuel@sholland.org>

Re: [PATCH v13 0/7] arm64: sunxi: Allwinner H616 SoC DT support

[Jernej Škrabec]

Dne petek, 08. julij 2022 ob 12:52:28 CEST je Andre Przywara napisal(a):
> Hi,
> 
> only some minor changes this time in the .dtsi, addressing the comments,
> many thanks to Jernej and Samuel for that! Also adding the R-b tags.
> 
> This keeps the TF-A reserved memory node, as a compromise for a smoother
> user experience.
> 
> This is on top of kernel.org's sunxi/dt-for-5.20, to get the new I2C
> fallback compatible. The series can be found here:
> https://github.com/apritzel/linux/commits/h616-v13
> 
> For a complete changelog, see below.
> 
> Thanks!
> Andre
> 
> ==================
> This series gathers patches to support the Allwinner H616 SoC. This is
> a rather uninspired SoC (Quad-A53 with the usual peripherals), but
> allows for some cheap development boards and TV boxes, and supports
> up to 4GB of DRAM.
> 
> Some DT binding patches are sprinkled throughout the series, to add
> the new compatible names right before they are used.
> Eventually we get the .dtsi for the SoC in patch 3, and the .dts for
> the OrangePi Zero2 board[1] later, followed by the .dts for the X96 Mate
> TV box[2] afterwards.
> 
> U-Boot and Trusted Firmware support is now merged in released versions,
> it allows booting via FEL or SD card, also you can TFTP kernels in on
> the OrangePi Zero 2 board.
> 
> Many thanks to Jernej for his tremendous help on this, also for the
> awesome input and help from the #linux-sunxi IRC channel.
> 
> The whole series (including the prerequisites) can also be found here:
> https://github.com/apritzel/linux/commits/h616-v13
> 
> Happy reviewing!
> 
> Cheers,
> Andre
> 
> [1] https://linux-sunxi.org/Orange_Pi_Zero_2
> [2] https://linux-sunxi.org/X96_Mate

Fixed emac compatible and applied, thanks!

Best regards,
Jernej

Re: [PATCH v13 0/7] arm64: sunxi: Allwinner H616 SoC DT support

[Linus Walleij]

On Fri, Jul 8, 2022 at 12:52 PM Andre Przywara <andre.przywara@arm.com> wrote:

> only some minor changes this time in the .dtsi, addressing the comments,
> many thanks to Jernej and Samuel for that! Also adding the R-b tags.

> Andre Przywara (7):
>   dt-bindings: pinctrl: sunxi: Make interrupts optional
>   dt-bindings: pinctrl: sunxi: allow vcc-pi-supply

These two (patches 2 & 4) applied to the pinctrl tree, I suppose it
is what I'm supposed to do?

If they end up also applied to the SoC tree it's not the end of the
world.

Yours,
Linus Walleij