Re: [PATCH v4 1/2] dt-bindings: iio: adc: add NCT7201 ADCs

[David Lechner <dlechner@baylibre.com>]

On 2/21/25 3:09 AM, Eason Yang wrote:
> Add a binding specification for the Nuvoton NCT7201/NCT7202 up to 12-bit
> ADCs with I2C interface.
> 
> Signed-off-by: Eason Yang <j2anfernee@gmail.com>
> ---
>  .../bindings/iio/adc/nuvoton,nct7201.yaml     | 57 +++++++++++++++++++
>  MAINTAINERS                                   |  1 +
>  2 files changed, 58 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/iio/adc/nuvoton,nct7201.yaml
> 
> diff --git a/Documentation/devicetree/bindings/iio/adc/nuvoton,nct7201.yaml b/Documentation/devicetree/bindings/iio/adc/nuvoton,nct7201.yaml
> new file mode 100644
> index 000000000000..830c37fd9f22
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/adc/nuvoton,nct7201.yaml
> @@ -0,0 +1,57 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/iio/adc/nuvoton,nct7201.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Nuvoton nct7201 and similar ADCs
> +
> +maintainers:
> +  - Eason Yang <j2anfernee@gmail.com>
> +
> +description: |
> +  The NCT7201/NCT7202 is a Nuvoton Hardware Monitor IC, contains up to 12 voltage
> +  monitoring channels, with SMBus interface, and up to 4 sets SMBus address
> +  selection by ADDR connection. It also provides ALERT# signal for event
> +  notification and reset input RSTIN# to recover it from a fault condition.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - nuvoton,nct7201
> +      - nuvoton,nct7202
> +
> +  reg:
> +    maxItems: 1
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  reset-gpios:
> +    maxItems: 1
> +

Maybe this was brought up before, but no power supply?

> +required:
> +  - compatible
> +  - reg
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +
> +    #include <dt-bindings/gpio/gpio.h>
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +
> +    i2c {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        adc@1d {
> +            compatible = "nuvoton,nct7202";
> +            reg = <0x1d>;
> +            interrupt-parent = <&gpio3>;
> +            interrupts = <30 IRQ_TYPE_LEVEL_LOW>;
> +            reset-gpios = <&gpio3 28 GPIO_ACTIVE_LOW>;
> +        };
> +    };
> +...
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 3864d473f52f..fdc4aa5c7eff 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -2831,6 +2831,7 @@ L:	openbmc@lists.ozlabs.org (moderated for non-subscribers)
>  S:	Supported
>  F:	Documentation/devicetree/bindings/*/*/*npcm*
>  F:	Documentation/devicetree/bindings/*/*npcm*
> +F:	Documentation/devicetree/bindings/iio/adc/nuvoton,nct7201.yaml

This (ARM/NUVOTON NPCM ARCHITECTURE) doesn't look like the right place for
adding a stand-alone chip. You will need to start a new section like:

NUVOTON NCT7201 IIO DRIVER

>  F:	Documentation/devicetree/bindings/rtc/nuvoton,nct3018y.yaml
>  F:	arch/arm/boot/dts/nuvoton/nuvoton-npcm*
>  F:	arch/arm/mach-npcm/