[PATCH v8 0/2] Add Qualcomm Technologies, Inc. Talos EVK SMARC support

[PATCH v8 0/2] Add Qualcomm Technologies, Inc. Talos EVK SMARC support

[Sudarshan Shetty]

[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #1: Type: text/plain; charset=yes, Size: 3490 bytes --]

Hi all,

This patch series adds device tree binding and board support for the
Qualcomm Technologies, Inc. Talos EVK SMARC platform based on the
QCS615 SoC.

The first patch introduces the DT binding entry for the Talos EVK
SMARC board, and the second patch adds the corresponding DTS
files for the platform.

Note:
USB(usb_1_dwc3) supports host-only mode based on the switch SW1 on
the SoM, which is purely a hardware controlled as USB-ID and USB-VBUS
is not connected the switching cannot be handled from SW.
Hence from SW Host-only mode is supported on Linux boot up.

Changes in v8:
 - This patch series depends on the below url
   https://lists.freedesktop.org/archives/dri-devel/2025-November/534473.html
 - Moved the contents of `talos-evk-cb.dtsi` to `talos-evk.dtsi`
   which will describe all the standard configuration of the EVK.
 - Introduced 'talos-evk-lvds-auo,g133han01.dtso' which has overlay
   to disable HDMI and adds the LVDS-related on top of the base
   dts file. (suggested by Bjorn)
 - Ethernet and Wi-Fi/BT are not (yet) supported.
 - Updated commit message.
 - No functional change in bindings file.

Changes in v7:
 - Added i2c clock frequency for i2c5 node.
 - Moved adv7535 controller section to talos-evk.dts file.
 - Reorder the usb nodes.
 - GPI_DMA nodes added in the device tree files.
 - No functional change in bindings file.

Changes in v6:
 - Clarified description of `talos-evk-cb.dtsi` to explain that it
   defines common carrier board interfaces shared between HDMI and
   LVDS variants, And It’s a single carrier board. HDMI and LVDS
   share the same DSI interface, and only one can be active at a
   time depending on a DIP switch.
 - Added missing newlines before 'status' and between the last property
   and subnode (suggested by Konrad).
 - Updated commit messages for clarity.

Changes in v5:
 - Updated commit message. (suggested by Krzysztof)
 - Introduced generic node name for can, dp, hdmi-bridge. (suggested by
   Krzysztof)
 - Introduced talos-evk-cb.dtsi, which has common carrier board
   interfaces.
 - No functional change in bindings file.

Changes in v4:
 - Updated product name to full form per Krzysztof’s feedback in
   dt-binding comment.
 - Hook up the ADV7535 DSI-to-HDMI bridge to base DTS file.
 - Add DP connector node and MDSS DisplayPort controller.
 - Added USB note in the cover letter for maintainers' awareness.

Changes in v3:
 - Addressed comments from Dmitry regarding USB1 `dr_mode` and
   added a DTS comment.
 - No functional change in bindings file.

Changes in v2:
 - Renamed compatible to "qcom,talos-evk" (suggested by Dmitry/Bjorn)
 - Merged enum entry with existing `qcs615-ride` block (Krzysztof)
 - Fixed subject and commit message to use imperative mood.

Thanks,
Sudarshan

Sudarshan Shetty (2):
  dt-bindings: arm: qcom: talos-evk: Add QCS615 Talos EVK SMARC platform
  arm64: dts: qcom: talos-evk: Add support for QCS615 talos evk board

 .../devicetree/bindings/arm/qcom.yaml         |   1 +
 arch/arm64/boot/dts/qcom/Makefile             |   3 +
 .../qcom/talos-evk-lvds-auo,g133han01.dtso    | 131 +++++
 arch/arm64/boot/dts/qcom/talos-evk-som.dtsi   | 447 ++++++++++++++++++
 arch/arm64/boot/dts/qcom/talos-evk.dts        | 137 ++++++
 5 files changed, 719 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso
 create mode 100644 arch/arm64/boot/dts/qcom/talos-evk-som.dtsi
 create mode 100644 arch/arm64/boot/dts/qcom/talos-evk.dts

-- 
2.34.1

[PATCH v8 1/2] dt-bindings: arm: qcom: talos-evk: Add QCS615 Talos EVK SMARC platform

[Sudarshan Shetty]

Add binding support for the Qualcomm Technologies, Inc. Talos EVK
SMARC platform based on the QCS615 SoC.

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sudarshan Shetty <tessolveupstream@gmail.com>
---
 Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 0a3222d6f368..a323be3d2ba2 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -862,6 +862,7 @@ properties:
       - items:
           - enum:
               - qcom,qcs615-ride
+              - qcom,talos-evk
           - const: qcom,qcs615
           - const: qcom,sm6150
 
-- 
2.34.1

[PATCH v8 2/2] arm64: dts: qcom: talos-evk: Add support for QCS615 talos evk board

[Sudarshan Shetty]

Add the device tree for the QCS615-based Talos EVK platform. The
platform is composed of a System-on-Module following the SMARC
standard, and a Carrier Board.

The Carrier Board supports several display configurations, HDMI and
LVDS. Both configurations use the same base hardware, with the display
selection controlled by a DIP switch.

Use a DTBO file, talos-evk-lvds-auo,g133han01.dtso, which defines an
overlay that disables HDMI and adds LVDS. The DTs file talos-evk
can describe the HDMI display configurations.

The initial device tree includes support for:
- CPU and memory
- UART
- GPIOs
- Regulators
- PMIC
- Early console
- AT24MAC602 EEPROM
- MCP2515 SPI to CAN
- ADV7535 DSI-to-HDMI bridge
- DisplayPort interface

Signed-off-by: Sudarshan Shetty <tessolveupstream@gmail.com>
---
 arch/arm64/boot/dts/qcom/Makefile             |   3 +
 .../qcom/talos-evk-lvds-auo,g133han01.dtso    | 131 +++++
 arch/arm64/boot/dts/qcom/talos-evk-som.dtsi   | 447 ++++++++++++++++++
 arch/arm64/boot/dts/qcom/talos-evk.dts        | 137 ++++++
 4 files changed, 718 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso
 create mode 100644 arch/arm64/boot/dts/qcom/talos-evk-som.dtsi
 create mode 100644 arch/arm64/boot/dts/qcom/talos-evk.dts

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 5b52f9e4e5f3..94c20074397c 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -305,6 +305,9 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sm8650-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8650-qrd.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8750-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8750-qrd.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= talos-evk.dtb
+talos-evk-lvds-auo,g133han01-dtbs	:= talos-evk.dtb talos-evk-lvds-auo,g133han01.dtbo
+dtb-$(CONFIG_ARCH_QCOM)	+= talos-evk-lvds-auo,g133han01.dtb
 x1e001de-devkit-el2-dtbs	:= x1e001de-devkit.dtb x1-el2.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e001de-devkit.dtb x1e001de-devkit-el2.dtb
 x1e78100-lenovo-thinkpad-t14s-el2-dtbs	:= x1e78100-lenovo-thinkpad-t14s.dtb x1-el2.dtbo
diff --git a/arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso b/arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso
new file mode 100644
index 000000000000..2a90d61892e7
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/talos-evk-lvds-auo,g133han01.dtso
@@ -0,0 +1,131 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+	backlight: backlight {
+		compatible = "gpio-backlight";
+		gpios = <&tlmm 115 GPIO_ACTIVE_HIGH>;
+		default-on;
+	};
+
+	hdmi-out {
+		status = "disabled";
+	};
+
+	lcd-pwm-en {
+		compatible = "gpio-backlight";
+		gpios = <&tlmm 59 GPIO_ACTIVE_HIGH>;
+		default-on;
+	};
+
+	panel-lvds {
+		compatible = "auo,g133han01";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* LVDS A (Odd pixels) */
+			port@0 {
+				reg = <0>;
+				dual-lvds-odd-pixels;
+
+				lvds_panel_out_a: endpoint {
+					remote-endpoint = <&sn65dsi84_out_a>;
+				};
+			};
+
+			/* LVDS B (Even pixels) */
+			port@1 {
+				reg = <1>;
+				dual-lvds-even-pixels;
+
+				lvds_panel_out_b: endpoint {
+					remote-endpoint = <&sn65dsi84_out_b>;
+				};
+			};
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	bridge@3d {
+		status = "disabled";
+	};
+
+	bridge: bridge@2c {
+		compatible = "ti,sn65dsi84";
+		reg = <0x2c>;
+		enable-gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>;
+		ti,dsi-lanes = <4>;
+		ti,lvds-format = "jeida-24";
+		ti,lvds-bpp = <24>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				sn65dsi84_in: endpoint {
+				data-lanes = <0 1 2 3>;
+				remote-endpoint = <&mdss_dsi0_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				sn65dsi84_out_a: endpoint {
+					data-lanes = <0 1 2 3>;
+					remote-endpoint = <&lvds_panel_out_a>;
+				};
+			};
+
+			port@3 {
+				reg = <3>;
+
+				sn65dsi84_out_b: endpoint {
+					data-lanes = <0 1 2 3>;
+					remote-endpoint = <&lvds_panel_out_b>;
+				};
+			};
+		};
+	};
+};
+
+&mdss_dsi0 {
+	vdda-supply = <&vreg_l11a>;
+
+	status = "okay";
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&sn65dsi84_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&tlmm {
+	lcd_bklt_en: lcd-bklt-en-state {
+		pins = "gpio115";
+		function = "gpio";
+		bias-disable;
+	};
+
+	lcd_bklt_pwm: lcd-bklt-pwm-state {
+		pins = "gpio59";
+		function = "gpio";
+		bias-disable;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/talos-evk-som.dtsi b/arch/arm64/boot/dts/qcom/talos-evk-som.dtsi
new file mode 100644
index 000000000000..7b576c7bf903
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/talos-evk-som.dtsi
@@ -0,0 +1,447 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "talos.dtsi"
+#include "pm8150.dtsi"
+/ {
+	aliases {
+		mmc0 = &sdhc_1;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	clocks {
+		sleep_clk: sleep-clk {
+			compatible = "fixed-clock";
+			clock-frequency = <32764>;
+			#clock-cells = <0>;
+		};
+
+		xo_board_clk: xo-board-clk {
+			compatible = "fixed-clock";
+			clock-frequency = <38400000>;
+			#clock-cells = <0>;
+		};
+	};
+
+	regulator-usb2-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "USB2_VBUS";
+		gpio = <&pm8150_gpios 10 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&usb2_en>;
+		pinctrl-names = "default";
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	vreg_v3p3_can: regulator-v3p3-can {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg-v3p3-can";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vreg_v5p0_can: regulator-v5p0-can {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg-v5p0-can";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pm8150-rpmh-regulators";
+		qcom,pmic-id = "a";
+
+		vreg_s3a: smps3 {
+			regulator-name = "vreg_s3a";
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <650000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s4a: smps4 {
+			regulator-name = "vreg_s4a";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1829000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s5a: smps5 {
+			regulator-name = "vreg_s5a";
+			regulator-min-microvolt = <1896000>;
+			regulator-max-microvolt = <2040000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s6a: smps6 {
+			regulator-name = "vreg_s6a";
+			regulator-min-microvolt = <1304000>;
+			regulator-max-microvolt = <1404000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1a: ldo1 {
+			regulator-name = "vreg_l1a";
+			regulator-min-microvolt = <488000>;
+			regulator-max-microvolt = <852000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2a: ldo2 {
+			regulator-name = "vreg_l2a";
+			regulator-min-microvolt = <1650000>;
+			regulator-max-microvolt = <3100000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3a: ldo3 {
+			regulator-name = "vreg_l3a";
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1248000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5a: ldo5 {
+			regulator-name = "vreg_l5a";
+			regulator-min-microvolt = <875000>;
+			regulator-max-microvolt = <975000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7a: ldo7 {
+			regulator-name = "vreg_l7a";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1900000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8a: ldo8 {
+			regulator-name = "vreg_l8a";
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1350000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10a: ldo10 {
+			regulator-name = "vreg_l10a";
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l11a: ldo11 {
+			regulator-name = "vreg_l11a";
+			regulator-min-microvolt = <1232000>;
+			regulator-max-microvolt = <1260000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12a: ldo12 {
+			regulator-name = "vreg_l12a";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1890000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13a: ldo13 {
+			regulator-name = "vreg_l13a";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3230000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15a: ldo15 {
+			regulator-name = "vreg_l15a";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1904000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l16a: ldo16 {
+			regulator-name = "vreg_l16a";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l17a: ldo17 {
+			regulator-name = "vreg_l17a";
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+&gpi_dma0 {
+	status = "okay";
+};
+
+&gpi_dma1 {
+	status = "okay";
+};
+
+&i2c5 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	eeprom@57 {
+		compatible = "atmel,24c02";
+		reg = <0x57>;
+		pagesize = <16>;
+	};
+
+	eeprom@5f {
+		compatible = "atmel,24mac602";
+		reg = <0x5f>;
+		pagesize = <16>;
+	};
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dp0 {
+	status = "okay";
+};
+
+&mdss_dp0_out {
+	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000>;
+	remote-endpoint = <&dp0_connector_in>;
+};
+
+&mdss_dp_phy {
+	vdda-phy-supply = <&vreg_l11a>;
+	vdda-pll-supply = <&vreg_l5a>;
+
+	status = "okay";
+};
+
+&mdss_dsi0 {
+	vdda-supply = <&vreg_l11a>;
+
+	status = "okay";
+};
+
+&mdss_dsi0_phy {
+	vdds-supply = <&vreg_l5a>;
+
+	status = "okay";
+};
+
+&pcie {
+	perst-gpios = <&tlmm 101 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 100 GPIO_ACTIVE_HIGH>;
+
+	pinctrl-0 = <&pcie_default_state>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie_phy {
+	vdda-phy-supply = <&vreg_l5a>;
+	vdda-pll-supply = <&vreg_l12a>;
+
+	status = "okay";
+};
+
+&pm8150_gpios {
+	usb2_en: usb2-en-state {
+		pins = "gpio10";
+		function = "normal";
+		output-enable;
+		power-source = <0>;
+	};
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/qcs615/adsp.mbn";
+
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	firmware-name = "qcom/qcs615/cdsp.mbn";
+
+	status = "okay";
+};
+
+&sdhc_1 {
+	pinctrl-0 = <&sdc1_state_on>;
+	pinctrl-1 = <&sdc1_state_off>;
+	pinctrl-names = "default", "sleep";
+
+	bus-width = <8>;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	mmc-hs400-enhanced-strobe;
+	vmmc-supply = <&vreg_l17a>;
+	vqmmc-supply = <&vreg_s4a>;
+
+	non-removable;
+	no-sd;
+	no-sdio;
+
+	status = "okay";
+};
+
+&spi6 {
+	status = "okay";
+
+	can@0 {
+		compatible = "microchip,mcp2515";
+		reg = <0>;
+		clock-frequency = <20000000>;
+		interrupts-extended = <&tlmm 87 IRQ_TYPE_LEVEL_LOW>;
+		spi-max-frequency = <10000000>;
+		vdd-supply = <&vreg_v3p3_can>;
+		xceiver-supply = <&vreg_v5p0_can>;
+	};
+};
+
+&tlmm {
+	pcie_default_state: pcie-default-state {
+		clkreq-pins {
+			pins = "gpio90";
+			function = "pcie_clk_req";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-pins {
+			pins = "gpio101";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		wake-pins {
+			pins = "gpio100";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_1_hsphy {
+	vdd-supply = <&vreg_l5a>;
+	vdda-pll-supply = <&vreg_l12a>;
+	vdda-phy-dpdm-supply = <&vreg_l13a>;
+
+	status = "okay";
+};
+
+&usb_2 {
+	status = "okay";
+};
+
+&usb_2_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_hsphy_2 {
+	vdd-supply = <&vreg_l5a>;
+	vdda-pll-supply = <&vreg_l12a>;
+	vdda-phy-dpdm-supply = <&vreg_l13a>;
+
+	status = "okay";
+};
+
+&usb_qmpphy {
+	vdda-phy-supply = <&vreg_l5a>;
+	vdda-pll-supply = <&vreg_l12a>;
+
+	status = "okay";
+};
+
+&ufs_mem_hc {
+	reset-gpios = <&tlmm 123 GPIO_ACTIVE_LOW>;
+	vcc-supply = <&vreg_l17a>;
+	vcc-max-microamp = <600000>;
+	vccq2-supply = <&vreg_s4a>;
+	vccq2-max-microamp = <600000>;
+
+	status = "okay";
+};
+
+&ufs_mem_phy {
+	vdda-phy-supply = <&vreg_l5a>;
+	vdda-pll-supply = <&vreg_l12a>;
+
+	status = "okay";
+};
+
+&venus {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/talos-evk.dts b/arch/arm64/boot/dts/qcom/talos-evk.dts
new file mode 100644
index 000000000000..c2f9a940c7a9
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/talos-evk.dts
@@ -0,0 +1,137 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+/dts-v1/;
+
+#include "talos-evk-som.dtsi"
+
+/ {
+	model = "Qualcomm QCS615 IQ 615 EVK";
+	compatible = "qcom,talos-evk", "qcom,qcs615", "qcom,sm6150";
+	chassis-type = "embedded";
+
+	aliases {
+		mmc1 = &sdhc_2;
+	};
+
+	dp-connector {
+		compatible = "dp-connector";
+		label = "DP0";
+		type = "full-size";
+
+		hpd-gpios = <&tlmm 104 GPIO_ACTIVE_HIGH>;
+
+		port {
+			dp0_connector_in: endpoint {
+				remote-endpoint = <&mdss_dp0_out>;
+			};
+		};
+	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "d";
+
+		port {
+			hdmi_con_out: endpoint {
+			remote-endpoint = <&adv7535_out>;
+			};
+		};
+	};
+
+	vreg_v1p8_out: regulator-v1p8-out {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg-v1p8-out";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vreg_v5p0_out>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vreg_v3p3_out: regulator-v3p3-out {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg-v3p3-out";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vreg_v5p0_out>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vreg_v5p0_out: regulator-v5p0-out {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg-v5p0-out";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		regulator-always-on;
+		/* Powered by system 20V rail (USBC_VBUS_IN) */
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+	status = "okay";
+	bridge: bridge@3d {
+		compatible = "adi,adv7535";
+		reg = <0x3d>;
+		avdd-supply = <&vreg_v1p8_out>;
+		dvdd-supply = <&vreg_v1p8_out>;
+		pvdd-supply = <&vreg_v1p8_out>;
+		a2vdd-supply = <&vreg_v1p8_out>;
+		v3p3-supply = <&vreg_v3p3_out>;
+		interrupts-extended = <&tlmm 26 IRQ_TYPE_LEVEL_LOW>;
+		adi,dsi-lanes = <4>;
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				adv7535_in: endpoint {
+					remote-endpoint = <&mdss_dsi0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				adv7535_out: endpoint {
+					remote-endpoint = <&hdmi_con_out>;
+				};
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&adv7535_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&pon_pwrkey {
+	status = "okay";
+};
+
+&pon_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+
+	status = "okay";
+};
+
+&sdhc_2 {
+	pinctrl-0 = <&sdc2_state_on>;
+	pinctrl-1 = <&sdc2_state_off>;
+	pinctrl-names = "default", "sleep";
+
+	bus-width = <4>;
+	cd-gpios = <&tlmm 99 GPIO_ACTIVE_LOW>;
+
+	vmmc-supply = <&vreg_l10a>;
+	vqmmc-supply = <&vreg_s4a>;
+
+	status = "okay";
+};
-- 
2.34.1

Re: [PATCH v8 1/2] dt-bindings: arm: qcom: talos-evk: Add QCS615 Talos EVK SMARC platform

[Rob Herring (Arm)]

On Sat, 29 Nov 2025 19:52:41 +0530, Sudarshan Shetty wrote:
> Add binding support for the Qualcomm Technologies, Inc. Talos EVK
> SMARC platform based on the QCS615 SoC.
> 
> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Signed-off-by: Sudarshan Shetty <tessolveupstream@gmail.com>
> ---
>  Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
>  1 file changed, 1 insertion(+)
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:
Documentation/devicetree/bindings/thermal/thermal-sensor.example.dtb: /example-0/soc/thermal-sensor@c263000: failed to match any schema with compatible: ['qcom,sdm845-tsens', 'qcom,tsens-v2']
Documentation/devicetree/bindings/thermal/thermal-sensor.example.dtb: /example-0/soc/thermal-sensor@c263000: failed to match any schema with compatible: ['qcom,sdm845-tsens', 'qcom,tsens-v2']
Documentation/devicetree/bindings/thermal/thermal-sensor.example.dtb: /example-0/soc/thermal-sensor@c265000: failed to match any schema with compatible: ['qcom,sdm845-tsens', 'qcom,tsens-v2']
Documentation/devicetree/bindings/thermal/thermal-sensor.example.dtb: /example-0/soc/thermal-sensor@c265000: failed to match any schema with compatible: ['qcom,sdm845-tsens', 'qcom,tsens-v2']

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20251129142242.3661349-2-tessolveupstream@gmail.com

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.

Re: [PATCH v8 1/2] dt-bindings: arm: qcom: talos-evk: Add QCS615 Talos EVK SMARC platform

[tessolveupstream]

On 29-11-2025 20:52, Rob Herring (Arm) wrote:
> 
> On Sat, 29 Nov 2025 19:52:41 +0530, Sudarshan Shetty wrote:
>> Add binding support for the Qualcomm Technologies, Inc. Talos EVK
>> SMARC platform based on the QCS615 SoC.
>>
>> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
>> Signed-off-by: Sudarshan Shetty <tessolveupstream@gmail.com>
>> ---
>>  Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
>>  1 file changed, 1 insertion(+)
>>
> 
> My bot found errors running 'make dt_binding_check' on your patch:
> 
> yamllint warnings/errors:
> 
> dtschema/dtc warnings/errors:
> Documentation/devicetree/bindings/thermal/thermal-sensor.example.dtb: /example-0/soc/thermal-sensor@c263000: failed to match any schema with compatible: ['qcom,sdm845-tsens', 'qcom,tsens-v2']
> Documentation/devicetree/bindings/thermal/thermal-sensor.example.dtb: /example-0/soc/thermal-sensor@c263000: failed to match any schema with compatible: ['qcom,sdm845-tsens', 'qcom,tsens-v2']
> Documentation/devicetree/bindings/thermal/thermal-sensor.example.dtb: /example-0/soc/thermal-sensor@c265000: failed to match any schema with compatible: ['qcom,sdm845-tsens', 'qcom,tsens-v2']
> Documentation/devicetree/bindings/thermal/thermal-sensor.example.dtb: /example-0/soc/thermal-sensor@c265000: failed to match any schema with compatible: ['qcom,sdm845-tsens', 'qcom,tsens-v2']
> 
> doc reference errors (make refcheckdocs):
> 
> See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20251129142242.3661349-2-tessolveupstream@gmail.com
> 
> The base for the series is generally the latest rc1. A different dependency
> should be noted in *this* patch.
> 
> If you already ran 'make dt_binding_check' and didn't see the above
> error(s), then make sure 'yamllint' is installed and dt-schema is up to
> date:
> 
> pip3 install dtschema --upgrade
> 
> Please check and re-submit after running the above command yourself. Note
> that DT_SCHEMA_FILES can be set to your schema file to speed up checking
> your schema. However, it must be unset to test all examples with your schema.
> 

Okay, got it. Will check and update the dependency in the 
next patch.