Re: [PATCH 2/2] arm64: dts: qcom: sm8250: Add device tree for Xiaomi Mi Pad 5 Pro

[Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>]

On 24/01/2023 14:53, Jianhua Lu wrote:
> Add support for Xiaomi Mi Pad 5 Pro, codename is xiaomi-elish.
> 
> This commit brings support for:
>   * ADSP/CDSP/SLPI/VENUS
>   * Backlight
>   * Battery fuel gauge
>   * Framebuffer
>   * PCIe0
>   * USB2.0
> 
> Note backlight driver (ktz8866) is waitting for upstreaming[1].
> [1] https://lore.kernel.org/linux-leds/20230120155018.15376-1-lujianhua000@gmail.com
> 
> Signed-off-by: Jianhua Lu <lujianhua000@gmail.com>
> ---
>  arch/arm64/boot/dts/qcom/Makefile             |   1 +
>  .../boot/dts/qcom/sm8250-xiaomi-elish.dts     | 594 ++++++++++++++++++
>  2 files changed, 595 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/sm8250-xiaomi-elish.dts
> 
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index b0423ca3e79f..769cee2b450f 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -184,6 +184,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sm8250-hdk.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm8250-mtp.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm8250-sony-xperia-edo-pdx203.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm8250-sony-xperia-edo-pdx206.dtb
> +dtb-$(CONFIG_ARCH_QCOM)	+= sm8250-xiaomi-elish.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm8350-hdk.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm8350-microsoft-surface-duo2.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm8350-mtp.dtb
> diff --git a/arch/arm64/boot/dts/qcom/sm8250-xiaomi-elish.dts b/arch/arm64/boot/dts/qcom/sm8250-xiaomi-elish.dts
> new file mode 100644
> index 000000000000..99ae6668e516
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sm8250-xiaomi-elish.dts
> @@ -0,0 +1,594 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2022, 2023 Jianhua Lu <lujianhua000@gmail.com>
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> +#include "sm8250.dtsi"
> +#include "pm8150.dtsi"
> +#include "pm8150b.dtsi"
> +#include "pm8150l.dtsi"
> +#include "pm8009.dtsi"
> +
> +/*
> + * Delete following upstream (sm8250.dtsi) reserved
> + * memory mappings which are different in this device.
> + */
> +/delete-node/ &xbl_aop_mem;
> +/delete-node/ &slpi_mem;
> +/delete-node/ &adsp_mem;
> +/delete-node/ &spss_mem;
> +/delete-node/ &cdsp_secure_heap;
> +
> +/ {
> +	model = "Xiaomi Mi Pad 5 Pro";
> +	compatible = "xiaomi,elish", "qcom,sm8250";
> +	classis-type = "tablet";
> +
> +	/* required for bootloader to select correct board */
> +	qcom,msm-id = <356 0x20001>; /* SM8250 v2.1 */
> +	qcom,board-id = <0x10008 0>;
> +
> +	chosen {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +
> +		framebuffer: framebuffer@9c000000 {
> +			compatible = "simple-framebuffer";
> +			reg = <0 0x9c000000 0 0x2300000>;
> +			width = <1600>;
> +			height = <2560>;
> +			stride = <(1600 * 4)>;
> +			format = "a8r8g8b8";
> +		};
> +	};
> +
> +	gpio_keys: gpio-keys {
> +		compatible = "gpio-keys";
> +
> +		vol-up {

Missing generic prefix.

Does not look like you tested the DTS against bindings. Please run `make
dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst
for instructions).

> +			label = "Volume Up";
> +			gpios = <&pm8150_gpios 6 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_VOLUMEUP>;
> +			debounce-interval = <15>;
> +			linux,can-disable;
> +			gpio-key,wakeup;
> +		};
> +	};
> +
> +	bl_vddpos_5p5: bl-vddpos-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "bl_vddpos_5p5";
> +		regulator-min-microvolt = <5500000>;
> +		regulator-max-microvolt = <5500000>;
> +		regulator-enable-ramp-delay = <233>;
> +		gpio = <&tlmm 130 0>;

Use defines for flags.

> +		enable-active-high;
> +		regulator-boot-on;
> +	};
> +
> +	bl_vddneg_5p5: bl-vddneg-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "bl_vddneg_5p5";
> +		regulator-min-microvolt = <5500000>;
> +		regulator-max-microvolt = <5500000>;
> +		regulator-enable-ramp-delay = <233>;
> +		gpio = <&tlmm 131 0>;

Use defines for flags.

> +		enable-active-high;
> +		regulator-boot-on;
> +	};
> +
> +	vph_pwr: vph-pwr-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vph_pwr";
> +		regulator-min-microvolt = <3700000>;
> +		regulator-max-microvolt = <3700000>;
> +	};
> +

(...)

> +
> +&cdsp {
> +	firmware-name = "qcom/sm8250/xiaomi/elish/cdsp.mbn";
> +	status = "okay";
> +};
> +
> +&gpi_dma0 {
> +	status = "okay";
> +};
> +
> +&gpi_dma1 {
> +	status = "okay";
> +};
> +
> +&gpi_dma2 {
> +	status = "okay";
> +};
> +
> +&i2c0 {
> +	clock-frequency = <400000>;
> +	status = "okay";
> +
> +	battery_fg@55 {

No underscores in node names. Generic node names, so just fuel-gauge

> +		compatible = "ti,bq27z561";
> +		reg = <0x55>;
> +		monitored-battery = <&battery_r>;
> +	};
> +};
> +
> +&i2c11 {
> +	clock-frequency = <400000>;
> +	status = "okay";
> +
> +	backlight: backlight@11 {
> +		compatible = "kinetic,ktz8866";
> +		reg = <0x11>;
> +		vddpos-supply = <&bl_vddpos_5p5>;
> +		vddneg-supply = <&bl_vddneg_5p5>;
> +		enable-gpios = <&tlmm 139 GPIO_ACTIVE_HIGH>;
> +		current-num-sinks = <5>;
> +		kinetic,current-ramp-delay-ms = <128>;
> +		kinetic,led-enable-ramp-delay-ms = <1>;
> +		kinetic,enable-lcd-bias;
> +	};
> +};
> +
> +&i2c13 {
> +	clock-frequency = <400000>;
> +	status = "okay";
> +
> +	battery_fg@55 {

Same problem

> +		compatible = "ti,bq27z561";
> +		reg = <0x55>;
> +		monitored-battery = <&battery_l>;
> +	};
> +};
Best regards,
Krzysztof