Re: [PATCH v1] arm64: dts: qcom: sa8540p-ride: enable pcie2a node

[Konrad Dybcio <konrad.dybcio@linaro.org>]

On 12.12.2022 12:45, Shazad Hussain wrote:
> Add the pcie2a, pcie2a_phy, and respective tlmm
> nodes that are needed to get pcie 2a controller
> enabled on Qdrive3.
> 
> This patch enables 4GB 64bit memory space for
> PCIE_2A to have BAR allocations of 64bit pref mem
> needed on this Qdrive3 platform with dual SoCs
> for root port and switch NT-EP. Hence this ranges
> property is overridden in sa8540p-ride.dts only.
> 
> Signed-off-by: Shazad Hussain <quic_shazhuss@quicinc.com>
> ---
> This patch depends on below patch series for vreg_l11a.
> 
> [v4] arm64: dts: qcom: sa8540p-ride: enable PCIe support
> https://lore.kernel.org/all/20221206161916.315640-1-bmasney@redhat.com/
> 
>  arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 44 +++++++++++++++++++++++
>  1 file changed, 44 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
> index bb4afd3a9632..ed20423ec8ac 100644
> --- a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
> +++ b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
> @@ -146,6 +146,27 @@ vreg_l8g: ldo8 {
>  	};
>  };
>  
> +&pcie2a {
> +	ranges = <0x01000000 0x0 0x3c200000 0x0 0x3c200000 0x0 0x100000>,
> +			 <0x02000000 0x0 0x3c300000 0x0 0x3c300000 0x0 0x1d00000>,
> +			 <0x03000000 0x5 0x00000000 0x5 0x00000000 0x1 0x00000000>;
Hi, please fix this indentation.

Konrad
> +
> +	perst-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>;
> +	wake-gpios = <&tlmm 145 GPIO_ACTIVE_HIGH>;
> +
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pcie2a_default>;
> +
> +	status = "okay";
> +};
> +
> +&pcie2a_phy {
> +	vdda-phy-supply = <&vreg_l11a>;
> +	vdda-pll-supply = <&vreg_l3a>;
> +
> +	status = "okay";
> +};
> +
>  &pcie3a {
>  	ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>,
>  	         <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x20000000>,
> @@ -247,6 +268,29 @@ &xo_board_clk {
>  /* PINCTRL */
>  
>  &tlmm {
> +	pcie2a_default: pcie2a-default-state {
> +		perst-pins {
> +			pins = "gpio143";
> +			function = "gpio";
> +			drive-strength = <2>;
> +			bias-pull-down;
> +		};
> +
> +		clkreq-pins {
> +			pins = "gpio142";
> +			function = "pcie2a_clkreq";
> +			drive-strength = <2>;
> +			bias-pull-up;
> +		};
> +
> +		wake-pins {
> +			pins = "gpio145";
> +			function = "gpio";
> +			drive-strength = <2>;
> +			bias-pull-up;
> +		};
> +	};
> +
>  	pcie3a_default: pcie3a-default-state {
>  		perst-pins {
>  			pins = "gpio151";