From: Frank Wang <frawang.cn@gmail.com>
To: Vinod Koul <vkoul@kernel.org>
Cc: kishon@kernel.org, robh@kernel.org, krzk+dt@kernel.org,
conor+dt@kernel.org, heiko@sntech.de,
linux-phy@lists.infradead.org, devicetree@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, linux-rockchip@lists.infradead.org,
william.wu@rock-chips.com, tim.chen@rock-chips.com,
Kever Yang <kever.yang@rock-chips.com>,
Frank Wang <frank.wang@rock-chips.com>
Subject: Re: [PATCH v2 2/2] phy: rockchip-naneng-combo: Support rk3576
Date: Fri, 18 Oct 2024 09:36:46 +0800 [thread overview]
Message-ID: <8f3bd853-55fc-4da5-8d68-eae5754f6933@gmail.com> (raw)
In-Reply-To: <ZxEgdHCQ3dTQeMRm@vaman>
Hi Vinod,
On 2024/10/17 22:34, Vinod Koul wrote:
> On 16-10-24, 10:35, Frank Wang wrote:
>> From: Kever Yang <kever.yang@rock-chips.com>
>>
>> phy0: pcie, sata
>> phy1: pcie, sata, usb3
> Can this be more verbose to explain what is being added in the patch
> below?
Sure, I'll amend and send a new version.
>> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
>> Signed-off-by: William Wu <william.wu@rock-chips.com>
>> Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
>> ---
>> Changelog:
>> v2:
>> - using constants macro instead of magic values.
>> - add more comments for PHY tuning operations.
>>
>> v1:
>> - https://patchwork.kernel.org/project/linux-phy/patch/20241015013351.4884-2-frawang.cn@gmail.com/
>>
>> .../rockchip/phy-rockchip-naneng-combphy.c | 274 ++++++++++++++++++
>> 1 file changed, 274 insertions(+)
>>
>> diff --git a/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
>> index 0a9989e41237f..25aa8d1981abc 100644
>> --- a/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
>> +++ b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
>> @@ -37,6 +37,10 @@
>> #define PHYREG8 0x1C
>> #define PHYREG8_SSC_EN BIT(4)
>>
>> +#define PHYREG10 0x24
>> +#define PHYREG10_SSC_PCM_MASK GENMASK(3, 0)
>> +#define PHYREG10_SSC_PCM_3500PPM 7
>> +
>> #define PHYREG11 0x28
>> #define PHYREG11_SU_TRIM_0_7 0xF0
>>
>> @@ -61,12 +65,19 @@
>> #define PHYREG16 0x3C
>> #define PHYREG16_SSC_CNT_VALUE 0x5f
>>
>> +#define PHYREG17 0x40
>> +
>> #define PHYREG18 0x44
>> #define PHYREG18_PLL_LOOP 0x32
>>
>> +#define PHYREG21 0x50
>> +#define PHYREG21_RX_SQUELCH_VAL 0x0D
>> +
>> #define PHYREG27 0x6C
>> #define PHYREG27_RX_TRIM_RK3588 0x4C
>>
>> +#define PHYREG30 0x74
>> +
>> #define PHYREG32 0x7C
>> #define PHYREG32_SSC_MASK GENMASK(7, 4)
>> #define PHYREG32_SSC_DIR_SHIFT 4
>> @@ -79,6 +90,7 @@
>> #define PHYREG33_PLL_KVCO_MASK GENMASK(4, 2)
>> #define PHYREG33_PLL_KVCO_SHIFT 2
>> #define PHYREG33_PLL_KVCO_VALUE 2
>> +#define PHYREG33_PLL_KVCO_VALUE_RK3576 4
>>
>> struct rockchip_combphy_priv;
>>
>> @@ -98,6 +110,7 @@ struct rockchip_combphy_grfcfg {
>> struct combphy_reg pipe_rxterm_set;
>> struct combphy_reg pipe_txelec_set;
>> struct combphy_reg pipe_txcomp_set;
>> + struct combphy_reg pipe_clk_24m;
>> struct combphy_reg pipe_clk_25m;
>> struct combphy_reg pipe_clk_100m;
>> struct combphy_reg pipe_phymode_sel;
>> @@ -584,6 +597,263 @@ static const struct rockchip_combphy_cfg rk3568_combphy_cfgs = {
>> .combphy_cfg = rk3568_combphy_cfg,
>> };
>>
>> +static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
>> +{
>> + const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
>> + unsigned long rate;
>> + u32 val;
>> +
>> + switch (priv->type) {
>> + case PHY_TYPE_PCIE:
>> + /* Set SSC downward spread spectrum */
>> + rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK,
>> + PHYREG32_SSC_DOWNWARD << PHYREG32_SSC_DIR_SHIFT,
>> + PHYREG32);
> If we use FIELD_GET|PREP, we can get rid of SHIFT defines
got it, thanks.
>> +
>> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_pcie, true);
>> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_pcie, true);
>> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con2_for_pcie, true);
>> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con3_for_pcie, true);
>> + break;
> Break here and before each case please
Okay.
>> + case PHY_TYPE_USB3:
>> + /* Set SSC downward spread spectrum */
>> + rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK,
>> + PHYREG32_SSC_DOWNWARD << PHYREG32_SSC_DIR_SHIFT,
>> + PHYREG32);
>> +
>> + /* Enable adaptive CTLE for USB3.0 Rx */
>> + val = readl(priv->mmio + PHYREG15);
>> + val |= PHYREG15_CTLE_EN;
>> + writel(val, priv->mmio + PHYREG15);
>> +
>> + /* Set PLL KVCO fine tuning signals */
>> + rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK, BIT(3), PHYREG33);
>> +
>> + /* Set PLL LPF R1 to su_trim[10:7]=1001 */
>> + writel(PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + PHYREG12);
>> +
>> + /* Set PLL input clock divider 1/2 */
>> + rockchip_combphy_updatel(priv, PHYREG6_PLL_DIV_MASK,
>> + PHYREG6_PLL_DIV_2 << PHYREG6_PLL_DIV_SHIFT,
>> + PHYREG6);
>> +
>> + /* Set PLL loop divider */
>> + writel(PHYREG18_PLL_LOOP, priv->mmio + PHYREG18);
>> +
>> + /* Set PLL KVCO to min and set PLL charge pump current to max */
>> + writel(PHYREG11_SU_TRIM_0_7, priv->mmio + PHYREG11);
>> +
>> + /* Set Rx squelch input filler bandwidth */
>> + writel(PHYREG21_RX_SQUELCH_VAL, priv->mmio + PHYREG21);
>> +
>> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txcomp_sel, false);
>> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txelec_sel, false);
>> + rockchip_combphy_param_write(priv->phy_grf, &cfg->usb_mode_set, true);
>> + break;
>> + case PHY_TYPE_SATA:
>> + /* Enable adaptive CTLE for SATA Rx */
>> + val = readl(priv->mmio + PHYREG15);
>> + val |= PHYREG15_CTLE_EN;
>> + writel(val, priv->mmio + PHYREG15);
>> +
>> + /* Set tx_rterm = 50 ohm and rx_rterm = 43.5 ohm */
>> + val = PHYREG7_TX_RTERM_50OHM << PHYREG7_TX_RTERM_SHIFT;
>> + val |= PHYREG7_RX_RTERM_44OHM << PHYREG7_RX_RTERM_SHIFT;
>> + writel(val, priv->mmio + PHYREG7);
>> +
>> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_sata, true);
>> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_sata, true);
>> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con2_for_sata, true);
>> + rockchip_combphy_param_write(priv->phy_grf, &cfg->con3_for_sata, true);
>> + rockchip_combphy_param_write(priv->pipe_grf, &cfg->pipe_con0_for_sata, true);
>> + rockchip_combphy_param_write(priv->pipe_grf, &cfg->pipe_con1_for_sata, true);
>> + break;
>> + default:
>> + dev_err(priv->dev, "incompatible PHY type\n");
>> + return -EINVAL;
>> + }
>> +
>> + rate = clk_get_rate(priv->refclk);
>> +
>> + switch (rate) {
>> + case REF_CLOCK_24MHz:
>> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_24m, true);
>> + if (priv->type == PHY_TYPE_USB3 || priv->type == PHY_TYPE_SATA) {
>> + /* Set ssc_cnt[9:0]=0101111101 & 31.5KHz */
>> + val = PHYREG15_SSC_CNT_VALUE << PHYREG15_SSC_CNT_SHIFT;
>> + rockchip_combphy_updatel(priv, PHYREG15_SSC_CNT_MASK,
>> + val, PHYREG15);
>> +
>> + writel(PHYREG16_SSC_CNT_VALUE, priv->mmio + PHYREG16);
>> +
>> + } else if (priv->type == PHY_TYPE_PCIE) {
>> + /* PLL KVCO tuning fine */
>> + val = PHYREG33_PLL_KVCO_VALUE_RK3576 << PHYREG33_PLL_KVCO_SHIFT;
>> + rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
>> + val, PHYREG33);
>> +
>> + /* Set up rx_pck invert and rx msb to disable */
>> + writel(0x00, priv->mmio + PHYREG27);
>> +
>> + /*
>> + * Set up SU adjust signal:
>> + * su_trim[7:0], PLL KVCO adjust bits[2:0] to min
>> + * su_trim[15:8], PLL LPF R1 adujst bits[9:7]=3'b011
>> + * su_trim[31:24], CKDRV adjust
>> + */
>> + writel(0x90, priv->mmio + PHYREG11);
>> + writel(0x02, priv->mmio + PHYREG12);
>> + writel(0x57, priv->mmio + PHYREG14);
>> +
>> + writel(PHYREG16_SSC_CNT_VALUE, priv->mmio + PHYREG16);
>> + }
>> + break;
>> + case REF_CLOCK_25MHz:
>> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_25m, true);
>> + break;
>> + case REF_CLOCK_100MHz:
>> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_100m, true);
>> + if (priv->type == PHY_TYPE_PCIE) {
>> + /* gate_tx_pck_sel length select work for L1SS */
>> + writel(0xc0, priv->mmio + PHYREG30);
>> +
>> + /* PLL KVCO tuning fine */
>> + val = PHYREG33_PLL_KVCO_VALUE_RK3576 << PHYREG33_PLL_KVCO_SHIFT;
>> + rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
>> + val, PHYREG33);
>> +
>> + /* Set up rx_trim: PLL LPF C1 85pf R1 1.25kohm */
>> + writel(0x4c, priv->mmio + PHYREG27);
>> +
>> + /*
>> + * Set up SU adjust signal:
>> + * su_trim[7:0], PLL KVCO adjust bits[2:0] to min
>> + * su_trim[15:8], bypass PLL loop divider code, and
>> + * PLL LPF R1 adujst bits[9:7]=3'b101
>> + * su_trim[23:16], CKRCV adjust
>> + * su_trim[31:24], CKDRV adjust
>> + */
>> + writel(0x90, priv->mmio + PHYREG11);
>> + writel(0x43, priv->mmio + PHYREG12);
>> + writel(0x88, priv->mmio + PHYREG13);
>> + writel(0x56, priv->mmio + PHYREG14);
>> + } else if (priv->type == PHY_TYPE_SATA) {
>> + /* downward spread spectrum +500ppm */
>> + val = PHYREG32_SSC_DOWNWARD << PHYREG32_SSC_DIR_SHIFT;
>> + val |= PHYREG32_SSC_OFFSET_500PPM << PHYREG32_SSC_OFFSET_SHIFT;
>> + rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK, val, PHYREG32);
>> +
>> + /* ssc ppm adjust to 3500ppm */
>> + rockchip_combphy_updatel(priv, PHYREG10_SSC_PCM_MASK,
>> + PHYREG10_SSC_PCM_3500PPM,
>> + PHYREG10);
>> + }
>> + break;
>> + default:
>> + dev_err(priv->dev, "Unsupported rate: %lu\n", rate);
>> + return -EINVAL;
>> + }
>> +
>> + if (priv->ext_refclk) {
>> + rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_ext, true);
>> + if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_100MHz) {
>> + val = PHYREG33_PLL_KVCO_VALUE_RK3576 << PHYREG33_PLL_KVCO_SHIFT;
>> + rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
>> + val, PHYREG33);
>> +
>> + /* Set up rx_trim: PLL LPF C1 85pf R1 2.5kohm */
>> + writel(0x0c, priv->mmio + PHYREG27);
>> +
>> + /*
>> + * Set up SU adjust signal:
>> + * su_trim[7:0], PLL KVCO adjust bits[2:0] to min
>> + * su_trim[15:8], bypass PLL loop divider code, and
>> + * PLL LPF R1 adujst bits[9:7]=3'b101.
>> + * su_trim[23:16], CKRCV adjust
>> + * su_trim[31:24], CKDRV adjust
>> + */
>> + writel(0x90, priv->mmio + PHYREG11);
>> + writel(0x43, priv->mmio + PHYREG12);
>> + writel(0x88, priv->mmio + PHYREG13);
>> + writel(0x56, priv->mmio + PHYREG14);
>> + }
>> + }
>> +
>> + if (priv->enable_ssc) {
>> + val = readl(priv->mmio + PHYREG8);
>> + val |= PHYREG8_SSC_EN;
>> + writel(val, priv->mmio + PHYREG8);
>> +
>> + if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_24MHz) {
>> + /* Set PLL loop divider */
>> + writel(0x00, priv->mmio + PHYREG17);
>> + writel(PHYREG18_PLL_LOOP, priv->mmio + PHYREG18);
>> +
>> + /* Set up rx_pck invert and rx msb to disable */
>> + writel(0x00, priv->mmio + PHYREG27);
>> +
>> + /*
>> + * Set up SU adjust signal:
>> + * su_trim[7:0], PLL KVCO adjust bits[2:0] to min
>> + * su_trim[15:8], PLL LPF R1 adujst bits[9:7]=3'b101
>> + * su_trim[23:16], CKRCV adjust
>> + * su_trim[31:24], CKDRV adjust
>> + */
>> + writel(0x90, priv->mmio + PHYREG11);
>> + writel(0x02, priv->mmio + PHYREG12);
>> + writel(0x08, priv->mmio + PHYREG13);
>> + writel(0x57, priv->mmio + PHYREG14);
>> + writel(0x40, priv->mmio + PHYREG15);
>> +
>> + writel(PHYREG16_SSC_CNT_VALUE, priv->mmio + PHYREG16);
>> + writel(PHYREG33_PLL_KVCO_VALUE_RK3576 << PHYREG33_PLL_KVCO_SHIFT,
>> + priv->mmio + PHYREG33);
>> + }
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static const struct rockchip_combphy_grfcfg rk3576_combphy_grfcfgs = {
>> + /* pipe-phy-grf */
>> + .pcie_mode_set = { 0x0000, 5, 0, 0x00, 0x11 },
>> + .usb_mode_set = { 0x0000, 5, 0, 0x00, 0x04 },
>> + .pipe_rxterm_set = { 0x0000, 12, 12, 0x00, 0x01 },
>> + .pipe_txelec_set = { 0x0004, 1, 1, 0x00, 0x01 },
>> + .pipe_txcomp_set = { 0x0004, 4, 4, 0x00, 0x01 },
>> + .pipe_clk_24m = { 0x0004, 14, 13, 0x00, 0x00 },
>> + .pipe_clk_25m = { 0x0004, 14, 13, 0x00, 0x01 },
>> + .pipe_clk_100m = { 0x0004, 14, 13, 0x00, 0x02 },
>> + .pipe_phymode_sel = { 0x0008, 1, 1, 0x00, 0x01 },
>> + .pipe_rate_sel = { 0x0008, 2, 2, 0x00, 0x01 },
>> + .pipe_rxterm_sel = { 0x0008, 8, 8, 0x00, 0x01 },
>> + .pipe_txelec_sel = { 0x0008, 12, 12, 0x00, 0x01 },
>> + .pipe_txcomp_sel = { 0x0008, 15, 15, 0x00, 0x01 },
>> + .pipe_clk_ext = { 0x000c, 9, 8, 0x02, 0x01 },
>> + .pipe_phy_status = { 0x0034, 6, 6, 0x01, 0x00 },
>> + .con0_for_pcie = { 0x0000, 15, 0, 0x00, 0x1000 },
>> + .con1_for_pcie = { 0x0004, 15, 0, 0x00, 0x0000 },
>> + .con2_for_pcie = { 0x0008, 15, 0, 0x00, 0x0101 },
>> + .con3_for_pcie = { 0x000c, 15, 0, 0x00, 0x0200 },
>> + .con0_for_sata = { 0x0000, 15, 0, 0x00, 0x0129 },
>> + .con1_for_sata = { 0x0004, 15, 0, 0x00, 0x0000 },
>> + .con2_for_sata = { 0x0008, 15, 0, 0x00, 0x80c1 },
>> + .con3_for_sata = { 0x000c, 15, 0, 0x00, 0x0407 },
>> + /* php-grf */
>> + .pipe_con0_for_sata = { 0x001C, 2, 0, 0x00, 0x2 },
>> + .pipe_con1_for_sata = { 0x0020, 2, 0, 0x00, 0x2 },
>> +};
>> +
>> +static const struct rockchip_combphy_cfg rk3576_combphy_cfgs = {
>> + .num_phys = 2,
>> + .phy_ids = {
>> + 0x2b050000,
>> + 0x2b060000
>> + },
>> + .grfcfg = &rk3576_combphy_grfcfgs,
>> + .combphy_cfg = rk3576_combphy_cfg,
>> +};
>> +
>> static int rk3588_combphy_cfg(struct rockchip_combphy_priv *priv)
>> {
>> const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
>> @@ -775,6 +1045,10 @@ static const struct of_device_id rockchip_combphy_of_match[] = {
>> .compatible = "rockchip,rk3568-naneng-combphy",
>> .data = &rk3568_combphy_cfgs,
>> },
>> + {
>> + .compatible = "rockchip,rk3576-naneng-combphy",
>> + .data = &rk3576_combphy_cfgs,
>> + },
>> {
>> .compatible = "rockchip,rk3588-naneng-combphy",
>> .data = &rk3588_combphy_cfgs,
>> --
>> 2.25.1
prev parent reply other threads:[~2024-10-18 1:36 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-10-16 2:35 [PATCH v2 1/2] dt-bindings: phy: rockchip: add rk3576 compatible Frank Wang
2024-10-16 2:35 ` [PATCH v2 2/2] phy: rockchip-naneng-combo: Support rk3576 Frank Wang
2024-10-17 14:34 ` Vinod Koul
2024-10-18 1:36 ` Frank Wang [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=8f3bd853-55fc-4da5-8d68-eae5754f6933@gmail.com \
--to=frawang.cn@gmail.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=frank.wang@rock-chips.com \
--cc=heiko@sntech.de \
--cc=kever.yang@rock-chips.com \
--cc=kishon@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-phy@lists.infradead.org \
--cc=linux-rockchip@lists.infradead.org \
--cc=robh@kernel.org \
--cc=tim.chen@rock-chips.com \
--cc=vkoul@kernel.org \
--cc=william.wu@rock-chips.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).