[PATCH 0/5] arm64: dts: renesas: sparrow-hawk: Add overlays for camera sensors

[PATCH 0/5] arm64: dts: renesas: sparrow-hawk: Add overlays for camera sensors

[Niklas Söderlund]

Hello,

This series adds a couple of overlays to verify the two CSI-2 busses 
exposed on the V4H Sparrow Hawk board. The two busses are exposed on two 
connectors labeled J1 and J2 on the board.

The first set adds overlays for the IMX219 camera sensor, one for each 
connector (patch 2/5 and 3/5). A Raspberry Pi Camera Module 2 have been 
used to verify the proper operation of the overlays.

The second sets adds overlays for the IMX462 camera sensors, also one 
for each connector (patch 4/5 and 5/5). A DFM 36SX462-ML camera module 
have been used to verify the proper operation of the overlays.

The reason two sets of overlays are needed is that the IMX219 uses 
2-lanes CSI-2 D-PHY bus, while the IMX462 uses a 4-lane CSI-2 D-PHY bus.  
To be able to properly test both situations on the board each sensor 
needs to be able to connected to each of the two external busses. 

Obviously only one sensor can be connected to J1, and one to J2 at any 
given time.

Patch 1/5 is a drive-by fix that adds an missing install target for an 
existing sparrow-hawk overlay. It could have been posted as a separate 
patch but could have caused potential conflicts so I kept it in this 
series.

Niklas Söderlund (5):
  arm64: dts: renesas: r8a779g3-sparrow-hawk-fan-pwm: Add missing
    install target
  arm64: dts: renesas: sparrow-hawk: Add overlay for IMX219 on J1
  arm64: dts: renesas: sparrow-hawk: Add overlay for IMX219 on J2
  arm64: dts: renesas: sparrow-hawk: Add overlay for IMX462 on J1
  arm64: dts: renesas: sparrow-hawk: Add overlay for IMX462 on J2

 arch/arm64/boot/dts/renesas/Makefile          |  13 ++
 ...8a779g3-sparrow-hawk-camera-j1-imx219.dtso | 120 +++++++++++++++++
 ...8a779g3-sparrow-hawk-camera-j1-imx462.dtso | 121 ++++++++++++++++++
 ...8a779g3-sparrow-hawk-camera-j2-imx219.dtso | 120 +++++++++++++++++
 ...8a779g3-sparrow-hawk-camera-j2-imx462.dtso | 121 ++++++++++++++++++
 5 files changed, 495 insertions(+)
 create mode 100644 arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-camera-j1-imx219.dtso
 create mode 100644 arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-camera-j1-imx462.dtso
 create mode 100644 arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-camera-j2-imx219.dtso
 create mode 100644 arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-camera-j2-imx462.dtso

-- 
2.50.0

[PATCH 1/5] arm64: dts: renesas: r8a779g3-sparrow-hawk-fan-pwm: Add missing install target

[Niklas Söderlund]

The target to consider the dtbo file for installation is missing, add
it.

Fixes: a719915e76f2 ("arm64: dts: renesas: r8a779g3: Add Retronix R-Car V4H Sparrow Hawk board support")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
---
 arch/arm64/boot/dts/renesas/Makefile | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/boot/dts/renesas/Makefile b/arch/arm64/boot/dts/renesas/Makefile
index 677ba3aa8931..47e46ef99d36 100644
--- a/arch/arm64/boot/dts/renesas/Makefile
+++ b/arch/arm64/boot/dts/renesas/Makefile
@@ -96,6 +96,7 @@ dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g2-white-hawk-single-ard-audio-da7212.dtb
 
 DTC_FLAGS_r8a779g3-sparrow-hawk += -Wno-spi_bus_bridge
 dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk.dtb
+dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-fan-pwm.dtbo
 r8a779g3-sparrow-hawk-fan-pwm-dtbs := r8a779g3-sparrow-hawk.dtb r8a779g3-sparrow-hawk-fan-pwm.dtbo
 dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-fan-pwm.dtb
 
-- 
2.50.0

[PATCH 2/5] arm64: dts: renesas: sparrow-hawk: Add overlay for IMX219 on J1

[Niklas Söderlund]

Add an overlay to connect an IMX219 camera sensor to the J1 connector.
The IMX219 utilizes 2 CSI-2 D-PHY lanes. This enables the video capture
pipeline behind the CSI40 Rx to be enabled to process images from the
sensor.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
---
 arch/arm64/boot/dts/renesas/Makefile          |   3 +
 ...8a779g3-sparrow-hawk-camera-j1-imx219.dtso | 120 ++++++++++++++++++
 2 files changed, 123 insertions(+)
 create mode 100644 arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-camera-j1-imx219.dtso

diff --git a/arch/arm64/boot/dts/renesas/Makefile b/arch/arm64/boot/dts/renesas/Makefile
index 47e46ef99d36..73218f7ec9af 100644
--- a/arch/arm64/boot/dts/renesas/Makefile
+++ b/arch/arm64/boot/dts/renesas/Makefile
@@ -96,7 +96,10 @@ dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g2-white-hawk-single-ard-audio-da7212.dtb
 
 DTC_FLAGS_r8a779g3-sparrow-hawk += -Wno-spi_bus_bridge
 dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk.dtb
+dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-camera-j1-imx219.dtbo
 dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-fan-pwm.dtbo
+r8a779g3-sparrow-hawk-camera-j1-imx219-dtbs := r8a779g3-sparrow-hawk.dtb r8a779g3-sparrow-hawk-camera-j1-imx219.dtbo
+dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-camera-j1-imx219.dtb
 r8a779g3-sparrow-hawk-fan-pwm-dtbs := r8a779g3-sparrow-hawk.dtb r8a779g3-sparrow-hawk-fan-pwm.dtbo
 dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-fan-pwm.dtb
 
diff --git a/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-camera-j1-imx219.dtso b/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-camera-j1-imx219.dtso
new file mode 100644
index 000000000000..b693bc4c6b55
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-camera-j1-imx219.dtso
@@ -0,0 +1,120 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Overlay for an IMX219 camera sensor in connector J1 on R-Car V4H
+ * ES3.0 Sparrow Hawk board.
+ *
+ * Copyright 2025 Renesas Electronics Corp.
+ * Copyright 2025 Niklas Söderlund <niklas.soderlund@ragnatech.se>
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/media/video-interfaces.h>
+
+&{/} {
+	clk_cam_j1: clk_cam_j1 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+		status = "okay";
+	};
+
+	/* Page 29 / CSI_IF_CN / J1 */
+	reg_cam_j1: reg_cam_j1 {
+		compatible = "regulator-fixed";
+		regulator-name = "reg_cam_j1";
+		enable-active-high;
+		status = "okay";
+		gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_cam_j1_dummy: reg_cam_j1_dummy {
+		compatible = "regulator-fixed";
+		regulator-name = "reg_cam_j1_dummy";
+		status = "okay";
+	};
+};
+
+&i2c1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	imx219_j1: imx219@10 {
+		compatible = "sony,imx219";
+		reg = <0x10>;
+		status = "okay";
+
+		clocks = <&clk_cam_j1>;
+
+		VANA-supply = <&reg_cam_j1>;
+		VDIG-supply = <&reg_cam_j1_dummy>;
+		VDDL-supply = <&reg_cam_j1_dummy>;
+
+		orientation = <2>;
+		rotation = <0>;
+
+		port {
+			imx219_j1_out: endpoint {
+				clock-noncontinuous;
+				link-frequencies = /bits/ 64 <456000000>;
+				data-lanes = <1 2>;
+				remote-endpoint = <&csi40_in>;
+			};
+		};
+	};
+};
+
+/* Page 29 / CSI_IF_CN */
+&csi40 {
+	status = "okay";
+
+	ports {
+		port {
+			csi40_in: endpoint {
+				bus-type = <MEDIA_BUS_TYPE_CSI2_DPHY>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+				remote-endpoint = <&imx219_j1_out>;
+			};
+		};
+	};
+};
+
+&isp0 {
+	status = "okay";
+};
+
+&vin00 {
+	status = "okay";
+};
+
+&vin01 {
+	status = "okay";
+};
+
+&vin02 {
+	status = "okay";
+};
+
+&vin03 {
+	status = "okay";
+};
+
+&vin04 {
+	status = "okay";
+};
+
+&vin05 {
+	status = "okay";
+};
+
+&vin06 {
+	status = "okay";
+};
+
+&vin07 {
+	status = "okay";
+};
-- 
2.50.0

[PATCH 3/5] arm64: dts: renesas: sparrow-hawk: Add overlay for IMX219 on J2

[Niklas Söderlund]

Add an overlay to connect an IMX219 camera sensor to the J2 connector.
The IMX219 utilizes 2 CSI-2 D-PHY lanes. This enables the video capture
pipeline behind the CSI41 Rx to be enabled to process images from the
sensor.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
---
 arch/arm64/boot/dts/renesas/Makefile          |   3 +
 ...8a779g3-sparrow-hawk-camera-j2-imx219.dtso | 120 ++++++++++++++++++
 2 files changed, 123 insertions(+)
 create mode 100644 arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-camera-j2-imx219.dtso

diff --git a/arch/arm64/boot/dts/renesas/Makefile b/arch/arm64/boot/dts/renesas/Makefile
index 73218f7ec9af..12803c4fbc80 100644
--- a/arch/arm64/boot/dts/renesas/Makefile
+++ b/arch/arm64/boot/dts/renesas/Makefile
@@ -97,9 +97,12 @@ dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g2-white-hawk-single-ard-audio-da7212.dtb
 DTC_FLAGS_r8a779g3-sparrow-hawk += -Wno-spi_bus_bridge
 dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk.dtb
 dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-camera-j1-imx219.dtbo
+dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-camera-j2-imx219.dtbo
 dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-fan-pwm.dtbo
 r8a779g3-sparrow-hawk-camera-j1-imx219-dtbs := r8a779g3-sparrow-hawk.dtb r8a779g3-sparrow-hawk-camera-j1-imx219.dtbo
 dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-camera-j1-imx219.dtb
+r8a779g3-sparrow-hawk-camera-j2-imx219-dtbs := r8a779g3-sparrow-hawk.dtb r8a779g3-sparrow-hawk-camera-j2-imx219.dtbo
+dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-camera-j2-imx219.dtb
 r8a779g3-sparrow-hawk-fan-pwm-dtbs := r8a779g3-sparrow-hawk.dtb r8a779g3-sparrow-hawk-fan-pwm.dtbo
 dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-fan-pwm.dtb
 
diff --git a/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-camera-j2-imx219.dtso b/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-camera-j2-imx219.dtso
new file mode 100644
index 000000000000..8df2e1f74ade
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-camera-j2-imx219.dtso
@@ -0,0 +1,120 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Overlay for an IMX219 camera sensor in connector J2 on R-Car V4H
+ * ES3.0 Sparrow Hawk board.
+ *
+ * Copyright 2025 Renesas Electronics Corp.
+ * Copyright 2025 Niklas Söderlund <niklas.soderlund@ragnatech.se>
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/media/video-interfaces.h>
+
+&{/} {
+	clk_cam_j2: clk_cam_j2 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+		status = "okay";
+	};
+
+	/* Page 29 / CSI_IF_CN / J2 */
+	reg_cam_j2: reg_cam_j2 {
+		compatible = "regulator-fixed";
+		regulator-name = "reg_cam_j2";
+		enable-active-high;
+		status = "okay";
+		gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_cam_j2_dummy: reg_cam_j2_dummy {
+		compatible = "regulator-fixed";
+		regulator-name = "reg_cam_j2_dummy";
+		status = "okay";
+	};
+};
+
+&i2c2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	imx219_j2: imx219@10 {
+		compatible = "sony,imx219";
+		reg = <0x10>;
+		status = "okay";
+
+		clocks = <&clk_cam_j2>;
+
+		VANA-supply = <&reg_cam_j2>;
+		VDIG-supply = <&reg_cam_j2_dummy>;
+		VDDL-supply = <&reg_cam_j2_dummy>;
+
+		orientation = <2>;
+		rotation = <0>;
+
+		port {
+			imx219_j2_out: endpoint {
+				clock-noncontinuous;
+				link-frequencies = /bits/ 64 <456000000>;
+				data-lanes = <1 2>;
+				remote-endpoint = <&csi41_in>;
+			};
+		};
+	};
+};
+
+/* Page 29 / CSI_IF_CN */
+&csi41 {
+	status = "okay";
+
+	ports {
+		port {
+			csi41_in: endpoint {
+				bus-type = <MEDIA_BUS_TYPE_CSI2_DPHY>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+				remote-endpoint = <&imx219_j2_out>;
+			};
+		};
+	};
+};
+
+&isp1 {
+	status = "okay";
+};
+
+&vin08 {
+	status = "okay";
+};
+
+&vin09 {
+	status = "okay";
+};
+
+&vin10 {
+	status = "okay";
+};
+
+&vin11 {
+	status = "okay";
+};
+
+&vin12 {
+	status = "okay";
+};
+
+&vin13 {
+	status = "okay";
+};
+
+&vin14 {
+	status = "okay";
+};
+
+&vin15 {
+	status = "okay";
+};
-- 
2.50.0

[PATCH 4/5] arm64: dts: renesas: sparrow-hawk: Add overlay for IMX462 on J1

[Niklas Söderlund]

Add an overlay to connect an IMX462 camera sensor to the J1 connector.
The IMX462 utilizes 4 CSI-2 D-PHY lanes. This enables the video capture
pipeline behind the CSI40 Rx to be enabled to process images from the
sensor.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
---
 arch/arm64/boot/dts/renesas/Makefile          |   3 +
 ...8a779g3-sparrow-hawk-camera-j1-imx462.dtso | 121 ++++++++++++++++++
 2 files changed, 124 insertions(+)
 create mode 100644 arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-camera-j1-imx462.dtso

diff --git a/arch/arm64/boot/dts/renesas/Makefile b/arch/arm64/boot/dts/renesas/Makefile
index 12803c4fbc80..79d174077ddc 100644
--- a/arch/arm64/boot/dts/renesas/Makefile
+++ b/arch/arm64/boot/dts/renesas/Makefile
@@ -97,10 +97,13 @@ dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g2-white-hawk-single-ard-audio-da7212.dtb
 DTC_FLAGS_r8a779g3-sparrow-hawk += -Wno-spi_bus_bridge
 dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk.dtb
 dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-camera-j1-imx219.dtbo
+dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-camera-j1-imx462.dtbo
 dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-camera-j2-imx219.dtbo
 dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-fan-pwm.dtbo
 r8a779g3-sparrow-hawk-camera-j1-imx219-dtbs := r8a779g3-sparrow-hawk.dtb r8a779g3-sparrow-hawk-camera-j1-imx219.dtbo
 dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-camera-j1-imx219.dtb
+r8a779g3-sparrow-hawk-camera-j1-imx462-dtbs := r8a779g3-sparrow-hawk.dtb r8a779g3-sparrow-hawk-camera-j1-imx462.dtbo
+dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-camera-j1-imx462.dtb
 r8a779g3-sparrow-hawk-camera-j2-imx219-dtbs := r8a779g3-sparrow-hawk.dtb r8a779g3-sparrow-hawk-camera-j2-imx219.dtbo
 dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-camera-j2-imx219.dtb
 r8a779g3-sparrow-hawk-fan-pwm-dtbs := r8a779g3-sparrow-hawk.dtb r8a779g3-sparrow-hawk-fan-pwm.dtbo
diff --git a/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-camera-j1-imx462.dtso b/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-camera-j1-imx462.dtso
new file mode 100644
index 000000000000..a1efb0ca48d8
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-camera-j1-imx462.dtso
@@ -0,0 +1,121 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Overlay for an IMX462 camera sensor in connector J1 on R-Car V4H
+ * ES3.0 Sparrow Hawk board.
+ *
+ * Copyright 2025 Renesas Electronics Corp.
+ * Copyright 2025 Niklas Söderlund <niklas.soderlund@ragnatech.se>
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/media/video-interfaces.h>
+
+&{/} {
+	clk_cam_j1: clk_cam_j1 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+		status = "okay";
+	};
+
+	/* Page 29 / CSI_IF_CN / J1 */
+	reg_cam_j1: reg_cam_j1 {
+		compatible = "regulator-fixed";
+		regulator-name = "reg_cam_j1";
+		enable-active-high;
+		status = "okay";
+		gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_cam_j1_dummy: reg_cam_j1_dummy {
+		compatible = "regulator-fixed";
+		regulator-name = "reg_cam_j1_dummy";
+		status = "okay";
+	};
+};
+
+&i2c1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	imx462_j1: imx462@1a {
+		compatible = "sony,imx462lqr";
+		reg = <0x1a>;
+		status = "okay";
+
+		clocks = <&clk_cam_j1>;
+		clock-names = "xclk";
+		clock-frequency = <37125000>;
+
+		vdddo-supply = <&reg_cam_j1>;
+		vdda-supply = <&reg_cam_j1_dummy>;
+		vddd-supply = <&reg_cam_j1_dummy>;
+
+		orientation = <2>;
+		rotation = <0>;
+
+		port {
+			imx462_j1_out: endpoint {
+				link-frequencies = /bits/ 64 <222750000 148500000>;
+				data-lanes = <1 2 3 4>;
+				remote-endpoint = <&csi40_in>;
+			};
+		};
+	};
+};
+
+/* Page 29 / CSI_IF_CN */
+&csi40 {
+	status = "okay";
+
+	ports {
+		port {
+			csi40_in: endpoint {
+				bus-type = <MEDIA_BUS_TYPE_CSI2_DPHY>;
+				clock-lanes = <0>;
+				data-lanes = <1 2 3 4>;
+				remote-endpoint = <&imx462_j1_out>;
+			};
+		};
+	};
+};
+
+&isp0 {
+	status = "okay";
+};
+
+&vin00 {
+	status = "okay";
+};
+
+&vin01 {
+	status = "okay";
+};
+
+&vin02 {
+	status = "okay";
+};
+
+&vin03 {
+	status = "okay";
+};
+
+&vin04 {
+	status = "okay";
+};
+
+&vin05 {
+	status = "okay";
+};
+
+&vin06 {
+	status = "okay";
+};
+
+&vin07 {
+	status = "okay";
+};
-- 
2.50.0

[PATCH 5/5] arm64: dts: renesas: sparrow-hawk: Add overlay for IMX462 on J2

[Niklas Söderlund]

Add an overlay to connect an IMX462 camera sensor to the J2 connector.
The IMX462 utilizes 4 CSI-2 D-PHY lanes. This enables the video capture
pipeline behind the CSI41 Rx to be enabled to process images from the
sensor.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
---
 arch/arm64/boot/dts/renesas/Makefile          |   3 +
 ...8a779g3-sparrow-hawk-camera-j2-imx462.dtso | 121 ++++++++++++++++++
 2 files changed, 124 insertions(+)
 create mode 100644 arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-camera-j2-imx462.dtso

diff --git a/arch/arm64/boot/dts/renesas/Makefile b/arch/arm64/boot/dts/renesas/Makefile
index 79d174077ddc..837e084cc07c 100644
--- a/arch/arm64/boot/dts/renesas/Makefile
+++ b/arch/arm64/boot/dts/renesas/Makefile
@@ -99,6 +99,7 @@ dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk.dtb
 dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-camera-j1-imx219.dtbo
 dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-camera-j1-imx462.dtbo
 dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-camera-j2-imx219.dtbo
+dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-camera-j2-imx462.dtbo
 dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-fan-pwm.dtbo
 r8a779g3-sparrow-hawk-camera-j1-imx219-dtbs := r8a779g3-sparrow-hawk.dtb r8a779g3-sparrow-hawk-camera-j1-imx219.dtbo
 dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-camera-j1-imx219.dtb
@@ -106,6 +107,8 @@ r8a779g3-sparrow-hawk-camera-j1-imx462-dtbs := r8a779g3-sparrow-hawk.dtb r8a779g
 dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-camera-j1-imx462.dtb
 r8a779g3-sparrow-hawk-camera-j2-imx219-dtbs := r8a779g3-sparrow-hawk.dtb r8a779g3-sparrow-hawk-camera-j2-imx219.dtbo
 dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-camera-j2-imx219.dtb
+r8a779g3-sparrow-hawk-camera-j2-imx462-dtbs := r8a779g3-sparrow-hawk.dtb r8a779g3-sparrow-hawk-camera-j2-imx462.dtbo
+dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-camera-j2-imx462.dtb
 r8a779g3-sparrow-hawk-fan-pwm-dtbs := r8a779g3-sparrow-hawk.dtb r8a779g3-sparrow-hawk-fan-pwm.dtbo
 dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-fan-pwm.dtb
 
diff --git a/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-camera-j2-imx462.dtso b/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-camera-j2-imx462.dtso
new file mode 100644
index 000000000000..e281f1086988
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a779g3-sparrow-hawk-camera-j2-imx462.dtso
@@ -0,0 +1,121 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Overlay for an IMX462 camera sensor in connector J2 on R-Car V4H
+ * ES3.0 Sparrow Hawk board.
+ *
+ * Copyright 2025 Renesas Electronics Corp.
+ * Copyright 2025 Niklas Söderlund <niklas.soderlund@ragnatech.se>
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/media/video-interfaces.h>
+
+&{/} {
+	clk_cam_j2: clk_cam_j2 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+		status = "okay";
+	};
+
+	/* Page 29 / CSI_IF_CN / J2 */
+	reg_cam_j2: reg_cam_j2 {
+		compatible = "regulator-fixed";
+		regulator-name = "reg_cam_j2";
+		enable-active-high;
+		status = "okay";
+		gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_cam_j2_dummy: reg_cam_j2_dummy {
+		compatible = "regulator-fixed";
+		regulator-name = "reg_cam_j2_dummy";
+		status = "okay";
+	};
+};
+
+&i2c2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	imx462_j2: imx462@1a {
+		compatible = "sony,imx462lqr";
+		reg = <0x1a>;
+		status = "okay";
+
+		clocks = <&clk_cam_j2>;
+		clock-names = "xclk";
+		clock-frequency = <37125000>;
+
+		vdddo-supply = <&reg_cam_j2>;
+		vdda-supply = <&reg_cam_j2_dummy>;
+		vddd-supply = <&reg_cam_j2_dummy>;
+
+		orientation = <2>;
+		rotation = <0>;
+
+		port {
+			imx462_j2_out: endpoint {
+				link-frequencies = /bits/ 64 <222750000 148500000>;
+				data-lanes = <1 2 3 4>;
+				remote-endpoint = <&csi41_in>;
+			};
+		};
+	};
+};
+
+/* Page 29 / CSI_IF_CN */
+&csi41 {
+	status = "okay";
+
+	ports {
+		port {
+			csi41_in: endpoint {
+				bus-type = <MEDIA_BUS_TYPE_CSI2_DPHY>;
+				clock-lanes = <0>;
+				data-lanes = <1 2 3 4>;
+				remote-endpoint = <&imx462_j2_out>;
+			};
+		};
+	};
+};
+
+&isp1 {
+	status = "okay";
+};
+
+&vin08 {
+	status = "okay";
+};
+
+&vin09 {
+	status = "okay";
+};
+
+&vin10 {
+	status = "okay";
+};
+
+&vin11 {
+	status = "okay";
+};
+
+&vin12 {
+	status = "okay";
+};
+
+&vin13 {
+	status = "okay";
+};
+
+&vin14 {
+	status = "okay";
+};
+
+&vin15 {
+	status = "okay";
+};
-- 
2.50.0

Re: [PATCH 1/5] arm64: dts: renesas: r8a779g3-sparrow-hawk-fan-pwm: Add missing install target

[Marek Vasut]

On 6/28/25 11:53 PM, Niklas Söderlund wrote:
> The target to consider the dtbo file for installation is missing, add
> it.
> 
> Fixes: a719915e76f2 ("arm64: dts: renesas: r8a779g3: Add Retronix R-Car V4H Sparrow Hawk board support")
> Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
> ---
>   arch/arm64/boot/dts/renesas/Makefile | 1 +
>   1 file changed, 1 insertion(+)
> 
> diff --git a/arch/arm64/boot/dts/renesas/Makefile b/arch/arm64/boot/dts/renesas/Makefile
> index 677ba3aa8931..47e46ef99d36 100644
> --- a/arch/arm64/boot/dts/renesas/Makefile
> +++ b/arch/arm64/boot/dts/renesas/Makefile
> @@ -96,6 +96,7 @@ dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g2-white-hawk-single-ard-audio-da7212.dtb
>   
>   DTC_FLAGS_r8a779g3-sparrow-hawk += -Wno-spi_bus_bridge
>   dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk.dtb
> +dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-fan-pwm.dtbo
>   r8a779g3-sparrow-hawk-fan-pwm-dtbs := r8a779g3-sparrow-hawk.dtb r8a779g3-sparrow-hawk-fan-pwm.dtbo
>   dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g3-sparrow-hawk-fan-pwm.dtb

Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>

I was not aware of this, thanks for pointing this out.

Re: [PATCH 2/5] arm64: dts: renesas: sparrow-hawk: Add overlay for IMX219 on J1

[Marek Vasut]

On 6/28/25 11:53 PM, Niklas Söderlund wrote:

Hello Niklas,

> +&{/} {
> +	clk_cam_j1: clk_cam_j1 {
> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <24000000>;
> +		status = "okay";
> +	};
> +
> +	/* Page 29 / CSI_IF_CN / J1 */
> +	reg_cam_j1: reg_cam_j1 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "reg_cam_j1";
> +		enable-active-high;
> +		status = "okay";
> +		gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	reg_cam_j1_dummy: reg_cam_j1_dummy {
> +		compatible = "regulator-fixed";
> +		regulator-name = "reg_cam_j1_dummy";
> +		status = "okay";

Is the 'status = "okay"' property needed for these regulators ? I think 
'status = "okay"' is the default behavior if "status" property is not 
present , so 'status = "okay"' is superfluous here.

Re: [PATCH 2/5] arm64: dts: renesas: sparrow-hawk: Add overlay for IMX219 on J1

[Niklas Söderlund]

Hi Marek,

Thanks for your feedback.

On 2025-06-29 15:40:52 +0200, Marek Vasut wrote:
> On 6/28/25 11:53 PM, Niklas Söderlund wrote:
> 
> Hello Niklas,
> 
> > +&{/} {
> > +	clk_cam_j1: clk_cam_j1 {
> > +		compatible = "fixed-clock";
> > +		#clock-cells = <0>;
> > +		clock-frequency = <24000000>;
> > +		status = "okay";
> > +	};
> > +
> > +	/* Page 29 / CSI_IF_CN / J1 */
> > +	reg_cam_j1: reg_cam_j1 {
> > +		compatible = "regulator-fixed";
> > +		regulator-name = "reg_cam_j1";
> > +		enable-active-high;
> > +		status = "okay";
> > +		gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>;
> > +	};
> > +
> > +	reg_cam_j1_dummy: reg_cam_j1_dummy {
> > +		compatible = "regulator-fixed";
> > +		regulator-name = "reg_cam_j1_dummy";
> > +		status = "okay";
> 
> Is the 'status = "okay"' property needed for these regulators ? I think
> 'status = "okay"' is the default behavior if "status" property is not
> present , so 'status = "okay"' is superfluous here.

Indeed you are correct, the status property for the fixed regulators are 
superfluous. Will drop in next version, thanks for teaching me something 
new.

-- 
Kind Regards,
Niklas Söderlund