[PATCH v3 0/7] clk: thead: Add support for TH1520 AP_SUBSYS clock controller

[PATCH v3 0/7] clk: thead: Add support for TH1520 AP_SUBSYS clock controller

[Drew Fustini]

This series adds support for the AP sub-system clock controller in the
T-Head TH1520 [1]. Yangtao Li originally submitted this series in May
2023 [2]. Jisheng made additional improvements and then passed on the
work in progress to me.

Link: https://openbeagle.org/beaglev-ahead/beaglev-ahead/-/blob/main/docs/TH1520%20System%20User%20Manual.pdf [1]
Link: https://lore.kernel.org/all/20230515054402.27633-1-frank.li@vivo.com/ [2]

Changes in v3:
 - dt-binding patch has been applied to clk-next by Stephen but I'm
   keeping it in the series for completeness.
 - move dt-bindings include after linux includes in driver
 - change rate to u64 in th1520_pll_vco_recalc_rate()
 - replace do_div() with normal division operation in both
   th1520_pll_vco_recalc_rate() and th1520_pll_postdiv_recalc_rate()
 - add static to ccu_mux structs: c910_i0_clk, c910_clk, uart_sclk

Changes in v2: 
 - Add clock property to the gpio nodes after Conor asked why they were
   missing. These clock gates correspond to enable bits in PERI_CLK_CFG.
 - Drop 2 cell address and size properties from the binding example per
   Conor and add Reviewed-by from from Conor.
 - Link: https://lore.kernel.org/linux-riscv/20240623-th1520-clk-v2-0-ad8d6432d9fb@tenstorrent.com/ 

Changes in v1:
 - Split th1520_clks into groups for gate, mux, div, pll
 - Convert gate clocks to devm_clk_hw_register_gate_parent_data()
 - Convert mux clocks to devm_clk_hw_register_mux_parent_data_table()
 - Split the PLL recalculation into th1520_pll_vco_recalc_rate() and
   th1520_pll_postdiv_recalc_rate(). Based on Emil's comments in v1,
   add logic to handle the fractional portion of feedback divide value
   when the delta-sigma modulator (DSM) is active.
 - Drop clock-names from the binding per Stephan to avoid relying on
   anything other than the cell index when describing clk_parent_data
   (note: I dropped Rob's Rb because I changed the binding patch)
 - Rename reg/reg2 to cfg0/cfg1 to match the SoC documentation
 - Rename struct for pll clocks from ccu_mdiv to ccu_pll
 - Rebase on v6.10-rc3, remove the dts node reordering patch from v3
   now that it is in mainline
 - Link: https://lore.kernel.org/linux-riscv/20240615-th1520-clk-v1-0-3ba4978c4d6b@tenstorrent.com/

Changes in RFC v3:
 - Drop redundant new line and unused clk label from the dts example in
   the DT binding which I failed to fix in v2.
 - Add patch [4] from Thomas Bonnefille that fixes dts node ordering in
   th1520.dtsi. Conor has already merged it into riscv-dt-for-next so
   the dts patches in this series are based on top of that.
 - Remove fixed uart clock and converted uart DT nodes to use clocks
   from the clock controller.
 - Remove fixed apb clock and converted the dma controller and timer DT
   nodes to use a clock from the clock controller.
 - Made ccu_disable_helper() and ccu_enable_helper() to static functions
 - Follow the advice from Stephen Boyd in Yangtao's original series to
   not use strings for clk tree topology. Created clk_parent_data arrays
   to be used with CLK_HW_INIT_PARENTS_DATA instead of parent strings.
 - Rebase on top of v6.9-rc7
 - Link: https://lore.kernel.org/all/20240506-th1520-clk-v3-0-085a18a23a7f@tenstorrent.com/

Changes in RFC v2:
 - squash the header file patch into the DT schema patch
 - describe the changes I made to original series in the cover letter
   instead of the individual patches
 - fix my typo in my email address
 - Link: https://lore.kernel.org/all/20240426-th1520-clk-v2-v2-0-96b829e6fcee@tenstorrent.com/

Changes in RFC v1 compared to the original series:
 - corrected the npu_clk enable bit
 - deduplicated CLK_NPU and CLK_NPU_AXI number in header
 - fixed c910_i0_clk reg typo
 - fixed checkpatch and dt_binding_check warnings
 - rebased on v6.9-rc5
 - revised commit descriptions
 - Link: https://lore.kernel.org/all/20240110-clk-th1520-v1-0-8b0682567984@tenstorrent.com/

Thank you,
Drew

---
Drew Fustini (7):
      dt-bindings: clock: Document T-Head TH1520 AP_SUBSYS controller
      clk: thead: Add support for T-Head TH1520 AP_SUBSYS clocks
      riscv: dts: thead: Add TH1520 AP_SUBSYS clock controller
      riscv: dts: thead: change TH1520 uart nodes to use clock controller
      riscv: dts: thead: change TH1520 mmc nodes to use clock controller
      riscv: dts: thead: update TH1520 dma and timer nodes to use clock controller
      riscv: dts: thead: add clock to TH1520 gpio nodes

 .../bindings/clock/thead,th1520-clk-ap.yaml        |   53 +
 MAINTAINERS                                        |    3 +
 arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts |   12 -
 .../boot/dts/thead/th1520-lichee-module-4a.dtsi    |   12 -
 arch/riscv/boot/dts/thead/th1520.dtsi              |   73 +-
 drivers/clk/Kconfig                                |    1 +
 drivers/clk/Makefile                               |    1 +
 drivers/clk/thead/Kconfig                          |   12 +
 drivers/clk/thead/Makefile                         |    2 +
 drivers/clk/thead/clk-th1520-ap.c                  | 1089 ++++++++++++++++++++
 include/dt-bindings/clock/thead,th1520-clk-ap.h    |   96 ++
 11 files changed, 1293 insertions(+), 61 deletions(-)
---
base-commit: 256abd8e550ce977b728be79a74e1729438b4948
change-id: 20240710-th1520-clk-0ad976e2a42e

Best regards,
-- 
Drew Fustini <dfustini@tenstorrent.com>

[PATCH v3 1/7] dt-bindings: clock: Document T-Head TH1520 AP_SUBSYS controller

[Drew Fustini]

Document bindings for the T-Head TH1520 AP sub-system clock controller.

Link: https://openbeagle.org/beaglev-ahead/beaglev-ahead/-/blob/main/docs/TH1520%20System%20User%20Manual.pdf
Co-developed-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Drew Fustini <dfustini@tenstorrent.com>
---
 .../bindings/clock/thead,th1520-clk-ap.yaml        | 53 ++++++++++++
 MAINTAINERS                                        |  2 +
 include/dt-bindings/clock/thead,th1520-clk-ap.h    | 96 ++++++++++++++++++++++
 3 files changed, 151 insertions(+)

diff --git a/Documentation/devicetree/bindings/clock/thead,th1520-clk-ap.yaml b/Documentation/devicetree/bindings/clock/thead,th1520-clk-ap.yaml
new file mode 100644
index 000000000000..0129bd0ba4b3
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/thead,th1520-clk-ap.yaml
@@ -0,0 +1,53 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/thead,th1520-clk-ap.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: T-HEAD TH1520 AP sub-system clock controller
+
+description: |
+  The T-HEAD TH1520 AP sub-system clock controller configures the
+  CPU, DPU, GMAC and TEE PLLs.
+
+  SoC reference manual
+  https://openbeagle.org/beaglev-ahead/beaglev-ahead/-/blob/main/docs/TH1520%20System%20User%20Manual.pdf
+
+maintainers:
+  - Jisheng Zhang <jszhang@kernel.org>
+  - Wei Fu <wefu@redhat.com>
+  - Drew Fustini <dfustini@tenstorrent.com>
+
+properties:
+  compatible:
+    const: thead,th1520-clk-ap
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: main oscillator (24MHz)
+
+  "#clock-cells":
+    const: 1
+    description:
+      See <dt-bindings/clock/thead,th1520-clk-ap.h> for valid indices.
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - "#clock-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/thead,th1520-clk-ap.h>
+    clock-controller@ef010000 {
+        compatible = "thead,th1520-clk-ap";
+        reg = <0xef010000 0x1000>;
+        clocks = <&osc>;
+        #clock-cells = <1>;
+    };
diff --git a/MAINTAINERS b/MAINTAINERS
index da5352dbd4f3..5b0e9c3534ea 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -19318,7 +19318,9 @@ M:	Guo Ren <guoren@kernel.org>
 M:	Fu Wei <wefu@redhat.com>
 L:	linux-riscv@lists.infradead.org
 S:	Maintained
+F:	Documentation/devicetree/bindings/clock/thead,th1520-clk-ap.yaml
 F:	arch/riscv/boot/dts/thead/
+F:	include/dt-bindings/clock/thead,th1520-clk-ap.h
 
 RNBD BLOCK DRIVERS
 M:	Md. Haris Iqbal <haris.iqbal@ionos.com>
diff --git a/include/dt-bindings/clock/thead,th1520-clk-ap.h b/include/dt-bindings/clock/thead,th1520-clk-ap.h
new file mode 100644
index 000000000000..a199784b3512
--- /dev/null
+++ b/include/dt-bindings/clock/thead,th1520-clk-ap.h
@@ -0,0 +1,96 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
+/*
+ * Copyright (C) 2023 Vivo Communication Technology Co. Ltd.
+ * Authors: Yangtao Li <frank.li@vivo.com>
+ */
+
+#ifndef _DT_BINDINGS_CLK_TH1520_H_
+#define _DT_BINDINGS_CLK_TH1520_H_
+
+#define CLK_CPU_PLL0		0
+#define CLK_CPU_PLL1		1
+#define CLK_GMAC_PLL		2
+#define CLK_VIDEO_PLL		3
+#define CLK_DPU0_PLL		4
+#define CLK_DPU1_PLL		5
+#define CLK_TEE_PLL		6
+#define CLK_C910_I0		7
+#define CLK_C910		8
+#define CLK_BROM		9
+#define CLK_BMU			10
+#define CLK_AHB2_CPUSYS_HCLK	11
+#define CLK_APB3_CPUSYS_PCLK	12
+#define CLK_AXI4_CPUSYS2_ACLK	13
+#define CLK_AON2CPU_A2X		14
+#define CLK_X2X_CPUSYS		15
+#define CLK_AXI_ACLK		16
+#define CLK_CPU2AON_X2H		17
+#define CLK_PERI_AHB_HCLK	18
+#define CLK_CPU2PERI_X2H	19
+#define CLK_PERI_APB_PCLK	20
+#define CLK_PERI2APB_PCLK	21
+#define CLK_PERISYS_APB1_HCLK	22
+#define CLK_PERISYS_APB2_HCLK	23
+#define CLK_PERISYS_APB3_HCLK	24
+#define CLK_PERISYS_APB4_HCLK	25
+#define CLK_OSC12M		26
+#define CLK_OUT1		27
+#define CLK_OUT2		28
+#define CLK_OUT3		29
+#define CLK_OUT4		30
+#define CLK_APB_PCLK		31
+#define CLK_NPU			32
+#define CLK_NPU_AXI		33
+#define CLK_VI			34
+#define CLK_VI_AHB		35
+#define CLK_VO_AXI		36
+#define CLK_VP_APB		37
+#define CLK_VP_AXI		38
+#define CLK_CPU2VP		39
+#define CLK_VENC		40
+#define CLK_DPU0		41
+#define CLK_DPU1		42
+#define CLK_EMMC_SDIO		43
+#define CLK_GMAC1		44
+#define CLK_PADCTRL1		45
+#define CLK_DSMART		46
+#define CLK_PADCTRL0		47
+#define CLK_GMAC_AXI		48
+#define CLK_GPIO3		49
+#define CLK_GMAC0		50
+#define CLK_PWM			51
+#define CLK_QSPI0		52
+#define CLK_QSPI1		53
+#define CLK_SPI			54
+#define CLK_UART0_PCLK		55
+#define CLK_UART1_PCLK		56
+#define CLK_UART2_PCLK		57
+#define CLK_UART3_PCLK		58
+#define CLK_UART4_PCLK		59
+#define CLK_UART5_PCLK		60
+#define CLK_GPIO0		61
+#define CLK_GPIO1		62
+#define CLK_GPIO2		63
+#define CLK_I2C0		64
+#define CLK_I2C1		65
+#define CLK_I2C2		66
+#define CLK_I2C3		67
+#define CLK_I2C4		68
+#define CLK_I2C5		69
+#define CLK_SPINLOCK		70
+#define CLK_DMA			71
+#define CLK_MBOX0		72
+#define CLK_MBOX1		73
+#define CLK_MBOX2		74
+#define CLK_MBOX3		75
+#define CLK_WDT0		76
+#define CLK_WDT1		77
+#define CLK_TIMER0		78
+#define CLK_TIMER1		79
+#define CLK_SRAM0		80
+#define CLK_SRAM1		81
+#define CLK_SRAM2		82
+#define CLK_SRAM3		83
+#define CLK_PLL_GMAC_100M	84
+#define CLK_UART_SCLK		85
+#endif

-- 
2.34.1

[PATCH v3 2/7] clk: thead: Add support for T-Head TH1520 AP_SUBSYS clocks

[Drew Fustini]

Add support for the AP sub-system clock controller in the T-Head TH1520.
This include CPU, DPU, GMAC and TEE PLLs.

Link: https://openbeagle.org/beaglev-ahead/beaglev-ahead/-/blob/main/docs/TH1520%20System%20User%20Manual.pdf
Co-developed-by: Yangtao Li <frank.li@vivo.com>
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Co-developed-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Link: https://git.beagleboard.org/beaglev-ahead/beaglev-ahead/-/tree/main/docs
Signed-off-by: Drew Fustini <dfustini@tenstorrent.com>
---
 MAINTAINERS                       |    1 +
 drivers/clk/Kconfig               |    1 +
 drivers/clk/Makefile              |    1 +
 drivers/clk/thead/Kconfig         |   12 +
 drivers/clk/thead/Makefile        |    2 +
 drivers/clk/thead/clk-th1520-ap.c | 1089 +++++++++++++++++++++++++++++++++++++
 6 files changed, 1106 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index 5b0e9c3534ea..bbe925242eb9 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -19320,6 +19320,7 @@ L:	linux-riscv@lists.infradead.org
 S:	Maintained
 F:	Documentation/devicetree/bindings/clock/thead,th1520-clk-ap.yaml
 F:	arch/riscv/boot/dts/thead/
+F:	drivers/clk/thead/clk-th1520-ap.c
 F:	include/dt-bindings/clock/thead,th1520-clk-ap.h
 
 RNBD BLOCK DRIVERS
diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index 3e9099504fad..d73ae04e427a 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -495,6 +495,7 @@ source "drivers/clk/starfive/Kconfig"
 source "drivers/clk/sunxi/Kconfig"
 source "drivers/clk/sunxi-ng/Kconfig"
 source "drivers/clk/tegra/Kconfig"
+source "drivers/clk/thead/Kconfig"
 source "drivers/clk/stm32/Kconfig"
 source "drivers/clk/ti/Kconfig"
 source "drivers/clk/uniphier/Kconfig"
diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
index 4abe16c8ccdf..f793a16cad40 100644
--- a/drivers/clk/Makefile
+++ b/drivers/clk/Makefile
@@ -127,6 +127,7 @@ obj-y					+= starfive/
 obj-$(CONFIG_ARCH_SUNXI)		+= sunxi/
 obj-y					+= sunxi-ng/
 obj-$(CONFIG_ARCH_TEGRA)		+= tegra/
+obj-$(CONFIG_ARCH_THEAD)		+= thead/
 obj-y					+= ti/
 obj-$(CONFIG_CLK_UNIPHIER)		+= uniphier/
 obj-$(CONFIG_ARCH_U8500)		+= ux500/
diff --git a/drivers/clk/thead/Kconfig b/drivers/clk/thead/Kconfig
new file mode 100644
index 000000000000..1710d50bf9d4
--- /dev/null
+++ b/drivers/clk/thead/Kconfig
@@ -0,0 +1,12 @@
+#SPDX-License-Identifier: GPL-2.0
+
+config CLK_THEAD_TH1520_AP
+	bool "T-HEAD TH1520 AP clock support"
+	depends on ARCH_THEAD || COMPILE_TEST
+	default ARCH_THEAD
+	select REGMAP_MMIO
+	help
+	  Say yes here to support the AP sub system clock controller
+	  on the T-HEAD TH1520 SoC. This includes configuration of
+	  both CPU PLLs, both DPU PLLs as well as the GMAC, VIDEO,
+	  and TEE PLLs.
diff --git a/drivers/clk/thead/Makefile b/drivers/clk/thead/Makefile
new file mode 100644
index 000000000000..7ee0bec1f251
--- /dev/null
+++ b/drivers/clk/thead/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_CLK_THEAD_TH1520_AP) += clk-th1520-ap.o
diff --git a/drivers/clk/thead/clk-th1520-ap.c b/drivers/clk/thead/clk-th1520-ap.c
new file mode 100644
index 000000000000..e6401e198517
--- /dev/null
+++ b/drivers/clk/thead/clk-th1520-ap.c
@@ -0,0 +1,1089 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2023 Jisheng Zhang <jszhang@kernel.org>
+ * Copyright (C) 2023 Vivo Communication Technology Co. Ltd.
+ *  Authors: Yangtao Li <frank.li@vivo.com>
+ */
+
+#include <dt-bindings/clock/thead,th1520-clk-ap.h>
+#include <linux/bitfield.h>
+#include <linux/clk-provider.h>
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#define TH1520_PLL_POSTDIV2	GENMASK(26, 24)
+#define TH1520_PLL_POSTDIV1	GENMASK(22, 20)
+#define TH1520_PLL_FBDIV	GENMASK(19, 8)
+#define TH1520_PLL_REFDIV	GENMASK(5, 0)
+#define TH1520_PLL_BYPASS	BIT(30)
+#define TH1520_PLL_DSMPD	BIT(24)
+#define TH1520_PLL_FRAC		GENMASK(23, 0)
+#define TH1520_PLL_FRAC_BITS    24
+
+struct ccu_internal {
+	u8	shift;
+	u8	width;
+};
+
+struct ccu_div_internal {
+	u8	shift;
+	u8	width;
+	u32	flags;
+};
+
+struct ccu_common {
+	int		clkid;
+	struct regmap	*map;
+	u16		cfg0;
+	u16		cfg1;
+	struct clk_hw	hw;
+};
+
+struct ccu_mux {
+	struct ccu_internal	mux;
+	struct ccu_common	common;
+};
+
+struct ccu_gate {
+	u32			enable;
+	struct ccu_common	common;
+};
+
+struct ccu_div {
+	u32			enable;
+	struct ccu_div_internal	div;
+	struct ccu_internal	mux;
+	struct ccu_common	common;
+};
+
+struct ccu_pll {
+	struct ccu_common	common;
+};
+
+#define TH_CCU_ARG(_shift, _width)					\
+	{								\
+		.shift	= _shift,					\
+		.width	= _width,					\
+	}
+
+#define TH_CCU_DIV_FLAGS(_shift, _width, _flags)			\
+	{								\
+		.shift	= _shift,					\
+		.width	= _width,					\
+		.flags	= _flags,					\
+	}
+
+#define CCU_GATE(_clkid, _struct, _name, _parent, _reg, _gate, _flags)	\
+	struct ccu_gate _struct = {					\
+		.enable	= _gate,					\
+		.common	= {						\
+			.clkid		= _clkid,			\
+			.cfg0		= _reg,				\
+			.hw.init	= CLK_HW_INIT_PARENTS_DATA(	\
+						_name,			\
+						_parent,		\
+						&clk_gate_ops,		\
+						_flags),		\
+		}							\
+	}
+
+static inline struct ccu_common *hw_to_ccu_common(struct clk_hw *hw)
+{
+	return container_of(hw, struct ccu_common, hw);
+}
+
+static inline struct ccu_mux *hw_to_ccu_mux(struct clk_hw *hw)
+{
+	struct ccu_common *common = hw_to_ccu_common(hw);
+
+	return container_of(common, struct ccu_mux, common);
+}
+
+static inline struct ccu_pll *hw_to_ccu_pll(struct clk_hw *hw)
+{
+	struct ccu_common *common = hw_to_ccu_common(hw);
+
+	return container_of(common, struct ccu_pll, common);
+}
+
+static inline struct ccu_div *hw_to_ccu_div(struct clk_hw *hw)
+{
+	struct ccu_common *common = hw_to_ccu_common(hw);
+
+	return container_of(common, struct ccu_div, common);
+}
+
+static inline struct ccu_gate *hw_to_ccu_gate(struct clk_hw *hw)
+{
+	struct ccu_common *common = hw_to_ccu_common(hw);
+
+	return container_of(common, struct ccu_gate, common);
+}
+
+static u8 ccu_get_parent_helper(struct ccu_common *common,
+				struct ccu_internal *mux)
+{
+	unsigned int val;
+	u8 parent;
+
+	regmap_read(common->map, common->cfg0, &val);
+	parent = val >> mux->shift;
+	parent &= GENMASK(mux->width - 1, 0);
+
+	return parent;
+}
+
+static int ccu_set_parent_helper(struct ccu_common *common,
+				 struct ccu_internal *mux,
+				 u8 index)
+{
+	return regmap_update_bits(common->map, common->cfg0,
+			GENMASK(mux->width - 1, 0) << mux->shift,
+			index << mux->shift);
+}
+
+static void ccu_disable_helper(struct ccu_common *common, u32 gate)
+{
+	if (!gate)
+		return;
+	regmap_update_bits(common->map, common->cfg0,
+			   gate, ~gate);
+}
+
+static int ccu_enable_helper(struct ccu_common *common, u32 gate)
+{
+	unsigned int val;
+	int ret;
+
+	if (!gate)
+		return 0;
+
+	ret = regmap_update_bits(common->map, common->cfg0, gate, gate);
+	regmap_read(common->map, common->cfg0, &val);
+	return ret;
+}
+
+static int ccu_is_enabled_helper(struct ccu_common *common, u32 gate)
+{
+	unsigned int val;
+
+	if (!gate)
+		return true;
+
+	regmap_read(common->map, common->cfg0, &val);
+	return val & gate;
+}
+
+static unsigned long ccu_div_recalc_rate(struct clk_hw *hw,
+					 unsigned long parent_rate)
+{
+	struct ccu_div *cd = hw_to_ccu_div(hw);
+	unsigned long rate;
+	unsigned int val;
+
+	regmap_read(cd->common.map, cd->common.cfg0, &val);
+	val = val >> cd->div.shift;
+	val &= GENMASK(cd->div.width - 1, 0);
+	rate = divider_recalc_rate(hw, parent_rate, val, NULL,
+				   cd->div.flags, cd->div.width);
+
+	return rate;
+}
+
+static u8 ccu_div_get_parent(struct clk_hw *hw)
+{
+	struct ccu_div *cd = hw_to_ccu_div(hw);
+
+	return ccu_get_parent_helper(&cd->common, &cd->mux);
+}
+
+static int ccu_div_set_parent(struct clk_hw *hw, u8 index)
+{
+	struct ccu_div *cd = hw_to_ccu_div(hw);
+
+	return ccu_set_parent_helper(&cd->common, &cd->mux, index);
+}
+
+static void ccu_div_disable(struct clk_hw *hw)
+{
+	struct ccu_div *cd = hw_to_ccu_div(hw);
+
+	ccu_disable_helper(&cd->common, cd->enable);
+}
+
+static int ccu_div_enable(struct clk_hw *hw)
+{
+	struct ccu_div *cd = hw_to_ccu_div(hw);
+
+	return ccu_enable_helper(&cd->common, cd->enable);
+}
+
+static int ccu_div_is_enabled(struct clk_hw *hw)
+{
+	struct ccu_div *cd = hw_to_ccu_div(hw);
+
+	return ccu_is_enabled_helper(&cd->common, cd->enable);
+}
+
+static const struct clk_ops ccu_div_ops = {
+	.disable	= ccu_div_disable,
+	.enable		= ccu_div_enable,
+	.is_enabled	= ccu_div_is_enabled,
+	.get_parent	= ccu_div_get_parent,
+	.set_parent	= ccu_div_set_parent,
+	.recalc_rate	= ccu_div_recalc_rate,
+	.determine_rate	= clk_hw_determine_rate_no_reparent,
+};
+
+static unsigned long th1520_pll_vco_recalc_rate(struct clk_hw *hw,
+						unsigned long parent_rate)
+{
+	struct ccu_pll *pll = hw_to_ccu_pll(hw);
+	unsigned long div, mul, frac;
+	unsigned int cfg0, cfg1;
+	u64 rate = parent_rate;
+
+	regmap_read(pll->common.map, pll->common.cfg0, &cfg0);
+	regmap_read(pll->common.map, pll->common.cfg1, &cfg1);
+
+	mul = FIELD_GET(TH1520_PLL_FBDIV, cfg0);
+	div = FIELD_GET(TH1520_PLL_REFDIV, cfg0);
+	if (!(cfg1 & TH1520_PLL_DSMPD)) {
+		mul <<= TH1520_PLL_FRAC_BITS;
+		frac = FIELD_GET(TH1520_PLL_FRAC, cfg1);
+		mul += frac;
+		div <<= TH1520_PLL_FRAC_BITS;
+	}
+	rate = parent_rate * mul;
+	rate = rate / div;
+	return rate;
+}
+
+static unsigned long th1520_pll_postdiv_recalc_rate(struct clk_hw *hw,
+						    unsigned long parent_rate)
+{
+	struct ccu_pll *pll = hw_to_ccu_pll(hw);
+	unsigned long div, rate = parent_rate;
+	unsigned int cfg0, cfg1;
+
+	regmap_read(pll->common.map, pll->common.cfg0, &cfg0);
+	regmap_read(pll->common.map, pll->common.cfg1, &cfg1);
+
+	if (cfg1 & TH1520_PLL_BYPASS)
+		return rate;
+
+	div = FIELD_GET(TH1520_PLL_POSTDIV1, cfg0) *
+	      FIELD_GET(TH1520_PLL_POSTDIV2, cfg0);
+
+	rate = rate / div;
+
+	return rate;
+}
+
+static unsigned long ccu_pll_recalc_rate(struct clk_hw *hw,
+					 unsigned long parent_rate)
+{
+	unsigned long rate = parent_rate;
+
+	rate = th1520_pll_vco_recalc_rate(hw, rate);
+	rate = th1520_pll_postdiv_recalc_rate(hw, rate);
+
+	return rate;
+}
+
+static const struct clk_ops clk_pll_ops = {
+	.recalc_rate	= ccu_pll_recalc_rate,
+};
+
+static const struct clk_parent_data osc_24m_clk[] = {
+	{ .index = 0 }
+};
+
+static struct ccu_pll cpu_pll0_clk = {
+	.common		= {
+		.clkid		= CLK_CPU_PLL0,
+		.cfg0		= 0x000,
+		.cfg1		= 0x004,
+		.hw.init	= CLK_HW_INIT_PARENTS_DATA("cpu-pll0",
+					      osc_24m_clk,
+					      &clk_pll_ops,
+					      0),
+	},
+};
+
+static struct ccu_pll cpu_pll1_clk = {
+	.common		= {
+		.clkid		= CLK_CPU_PLL1,
+		.cfg0		= 0x010,
+		.cfg1		= 0x014,
+		.hw.init	= CLK_HW_INIT_PARENTS_DATA("cpu-pll1",
+					      osc_24m_clk,
+					      &clk_pll_ops,
+					      0),
+	},
+};
+
+static struct ccu_pll gmac_pll_clk = {
+	.common		= {
+		.clkid		= CLK_GMAC_PLL,
+		.cfg0		= 0x020,
+		.cfg1		= 0x024,
+		.hw.init	= CLK_HW_INIT_PARENTS_DATA("gmac-pll",
+					      osc_24m_clk,
+					      &clk_pll_ops,
+					      0),
+	},
+};
+
+static const struct clk_hw *gmac_pll_clk_parent[] = {
+	&gmac_pll_clk.common.hw
+};
+
+static const struct clk_parent_data gmac_pll_clk_pd[] = {
+	{ .hw = &gmac_pll_clk.common.hw }
+};
+
+static struct ccu_pll video_pll_clk = {
+	.common		= {
+		.clkid		= CLK_VIDEO_PLL,
+		.cfg0		= 0x030,
+		.cfg1		= 0x034,
+		.hw.init	= CLK_HW_INIT_PARENTS_DATA("video-pll",
+					      osc_24m_clk,
+					      &clk_pll_ops,
+					      0),
+	},
+};
+
+static const struct clk_hw *video_pll_clk_parent[] = {
+	&video_pll_clk.common.hw
+};
+
+static const struct clk_parent_data video_pll_clk_pd[] = {
+	{ .hw = &video_pll_clk.common.hw }
+};
+
+static struct ccu_pll dpu0_pll_clk = {
+	.common		= {
+		.clkid		= CLK_DPU0_PLL,
+		.cfg0		= 0x040,
+		.cfg1		= 0x044,
+		.hw.init	= CLK_HW_INIT_PARENTS_DATA("dpu0-pll",
+					      osc_24m_clk,
+					      &clk_pll_ops,
+					      0),
+	},
+};
+
+static const struct clk_hw *dpu0_pll_clk_parent[] = {
+	&dpu0_pll_clk.common.hw
+};
+
+static struct ccu_pll dpu1_pll_clk = {
+	.common		= {
+		.clkid		= CLK_DPU1_PLL,
+		.cfg0		= 0x050,
+		.cfg1		= 0x054,
+		.hw.init	= CLK_HW_INIT_PARENTS_DATA("dpu1-pll",
+					      osc_24m_clk,
+					      &clk_pll_ops,
+					      0),
+	},
+};
+
+static const struct clk_hw *dpu1_pll_clk_parent[] = {
+	&dpu1_pll_clk.common.hw
+};
+
+static struct ccu_pll tee_pll_clk = {
+	.common		= {
+		.clkid		= CLK_TEE_PLL,
+		.cfg0		= 0x060,
+		.cfg1		= 0x064,
+		.hw.init	= CLK_HW_INIT_PARENTS_DATA("tee-pll",
+					      osc_24m_clk,
+					      &clk_pll_ops,
+					      0),
+	},
+};
+
+static const struct clk_parent_data c910_i0_parents[] = {
+	{ .hw = &cpu_pll0_clk.common.hw },
+	{ .index = 0 }
+};
+
+struct ccu_mux c910_i0_clk = {
+	.mux	= TH_CCU_ARG(1, 1),
+	.common	= {
+		.clkid		= CLK_C910_I0,
+		.cfg0		= 0x100,
+		.hw.init	= CLK_HW_INIT_PARENTS_DATA("c910-i0",
+					      c910_i0_parents,
+					      &clk_mux_ops,
+					      0),
+	}
+};
+
+static const struct clk_parent_data c910_parents[] = {
+	{ .hw = &c910_i0_clk.common.hw },
+	{ .hw = &cpu_pll1_clk.common.hw }
+};
+
+struct ccu_mux c910_clk = {
+	.mux	= TH_CCU_ARG(0, 1),
+	.common	= {
+		.clkid		= CLK_C910,
+		.cfg0		= 0x100,
+		.hw.init	= CLK_HW_INIT_PARENTS_DATA("c910",
+					      c910_parents,
+					      &clk_mux_ops,
+					      0),
+	}
+};
+
+static const struct clk_parent_data ahb2_cpusys_parents[] = {
+	{ .hw = &gmac_pll_clk.common.hw },
+	{ .index = 0 }
+};
+
+static struct ccu_div ahb2_cpusys_hclk = {
+	.div		= TH_CCU_DIV_FLAGS(0, 3, CLK_DIVIDER_ONE_BASED),
+	.mux		= TH_CCU_ARG(5, 1),
+	.common		= {
+		.clkid          = CLK_AHB2_CPUSYS_HCLK,
+		.cfg0		= 0x120,
+		.hw.init	= CLK_HW_INIT_PARENTS_DATA("ahb2-cpusys-hclk",
+						      ahb2_cpusys_parents,
+						      &ccu_div_ops,
+						      0),
+	},
+};
+
+static const struct clk_parent_data ahb2_cpusys_hclk_pd[] = {
+	{ .hw = &ahb2_cpusys_hclk.common.hw }
+};
+
+static const struct clk_hw *ahb2_cpusys_hclk_parent[] = {
+	&ahb2_cpusys_hclk.common.hw,
+};
+
+static struct ccu_div apb3_cpusys_pclk = {
+	.div		= TH_CCU_ARG(0, 3),
+	.common		= {
+		.clkid          = CLK_APB3_CPUSYS_PCLK,
+		.cfg0		= 0x130,
+		.hw.init	= CLK_HW_INIT_PARENTS_HW("apb3-cpusys-pclk",
+							   ahb2_cpusys_hclk_parent,
+							   &ccu_div_ops,
+							   0),
+	},
+};
+
+static const struct clk_parent_data apb3_cpusys_pclk_pd[] = {
+	{ .hw = &apb3_cpusys_pclk.common.hw }
+};
+
+static struct ccu_div axi4_cpusys2_aclk = {
+	.div		= TH_CCU_DIV_FLAGS(0, 3, CLK_DIVIDER_ONE_BASED),
+	.common		= {
+		.clkid          = CLK_AXI4_CPUSYS2_ACLK,
+		.cfg0		= 0x134,
+		.hw.init	= CLK_HW_INIT_PARENTS_HW("axi4-cpusys2-aclk",
+					      gmac_pll_clk_parent,
+					      &ccu_div_ops,
+					      0),
+	},
+};
+
+static const struct clk_parent_data axi4_cpusys2_aclk_pd[] = {
+	{ .hw = &axi4_cpusys2_aclk.common.hw }
+};
+
+static const struct clk_parent_data axi_parents[] = {
+	{ .hw = &video_pll_clk.common.hw },
+	{ .index = 0 }
+};
+
+static struct ccu_div axi_aclk = {
+	.div		= TH_CCU_DIV_FLAGS(0, 4, CLK_DIVIDER_ONE_BASED),
+	.mux		= TH_CCU_ARG(5, 1),
+	.common		= {
+		.clkid          = CLK_AXI_ACLK,
+		.cfg0		= 0x138,
+		.hw.init	= CLK_HW_INIT_PARENTS_DATA("axi-aclk",
+						      axi_parents,
+						      &ccu_div_ops,
+						      0),
+	},
+};
+
+static const struct clk_parent_data axi_aclk_pd[] = {
+	{ .hw = &axi_aclk.common.hw }
+};
+
+static const struct clk_parent_data perisys_ahb_hclk_parents[] = {
+	{ .hw = &gmac_pll_clk.common.hw },
+	{ .index = 0 },
+};
+
+static struct ccu_div perisys_ahb_hclk = {
+	.enable		= BIT(6),
+	.div		= TH_CCU_DIV_FLAGS(0, 4, CLK_DIVIDER_ONE_BASED),
+	.mux		= TH_CCU_ARG(5, 1),
+	.common		= {
+		.clkid          = CLK_PERI_AHB_HCLK,
+		.cfg0		= 0x140,
+		.hw.init	= CLK_HW_INIT_PARENTS_DATA("perisys-ahb-hclk",
+						      perisys_ahb_hclk_parents,
+						      &ccu_div_ops,
+						      0),
+	},
+};
+
+static const struct clk_parent_data perisys_ahb_hclk_pd[] = {
+	{ .hw = &perisys_ahb_hclk.common.hw }
+};
+
+static const struct clk_hw *perisys_ahb_hclk_parent[] = {
+	&perisys_ahb_hclk.common.hw
+};
+
+static struct ccu_div perisys_apb_pclk = {
+	.div		= TH_CCU_ARG(0, 3),
+	.common		= {
+		.clkid          = CLK_PERI_APB_PCLK,
+		.cfg0		= 0x150,
+		.hw.init	= CLK_HW_INIT_PARENTS_HW("perisys-apb-pclk",
+					      perisys_ahb_hclk_parent,
+					      &ccu_div_ops,
+					      0),
+	},
+};
+
+static const struct clk_parent_data perisys_apb_pclk_pd[] = {
+	{ .hw = &perisys_apb_pclk.common.hw }
+};
+
+static struct ccu_div peri2sys_apb_pclk = {
+	.div		= TH_CCU_DIV_FLAGS(4, 3, CLK_DIVIDER_ONE_BASED),
+	.common		= {
+		.clkid          = CLK_PERI2APB_PCLK,
+		.cfg0		= 0x150,
+		.hw.init	= CLK_HW_INIT_PARENTS_HW("peri2sys-apb-pclk",
+					      gmac_pll_clk_parent,
+					      &ccu_div_ops,
+					      0),
+	},
+};
+
+static const struct clk_parent_data peri2sys_apb_pclk_pd[] = {
+	{ .hw = &peri2sys_apb_pclk.common.hw }
+};
+
+static CLK_FIXED_FACTOR_FW_NAME(osc12m_clk, "osc_12m", "osc_24m", 2, 1, 0);
+
+static const char * const out_parents[] = { "osc_24m", "osc_12m" };
+
+static struct ccu_div out1_clk = {
+	.enable		= BIT(5),
+	.div		= TH_CCU_DIV_FLAGS(0, 3, CLK_DIVIDER_ONE_BASED),
+	.mux		= TH_CCU_ARG(4, 1),
+	.common		= {
+		.clkid          = CLK_OUT1,
+		.cfg0		= 0x1b4,
+		.hw.init	= CLK_HW_INIT_PARENTS("out1",
+						      out_parents,
+						      &ccu_div_ops,
+						      0),
+	},
+};
+
+static struct ccu_div out2_clk = {
+	.enable		= BIT(5),
+	.div		= TH_CCU_DIV_FLAGS(0, 3, CLK_DIVIDER_ONE_BASED),
+	.mux		= TH_CCU_ARG(4, 1),
+	.common		= {
+		.clkid          = CLK_OUT2,
+		.cfg0		= 0x1b8,
+		.hw.init	= CLK_HW_INIT_PARENTS("out2",
+						      out_parents,
+						      &ccu_div_ops,
+						      0),
+	},
+};
+
+static struct ccu_div out3_clk = {
+	.enable		= BIT(5),
+	.div		= TH_CCU_DIV_FLAGS(0, 3, CLK_DIVIDER_ONE_BASED),
+	.mux		= TH_CCU_ARG(4, 1),
+	.common		= {
+		.clkid          = CLK_OUT3,
+		.cfg0		= 0x1bc,
+		.hw.init	= CLK_HW_INIT_PARENTS("out3",
+						      out_parents,
+						      &ccu_div_ops,
+						      0),
+	},
+};
+
+static struct ccu_div out4_clk = {
+	.enable		= BIT(5),
+	.div		= TH_CCU_DIV_FLAGS(0, 3, CLK_DIVIDER_ONE_BASED),
+	.mux		= TH_CCU_ARG(4, 1),
+	.common		= {
+		.clkid          = CLK_OUT4,
+		.cfg0		= 0x1c0,
+		.hw.init	= CLK_HW_INIT_PARENTS("out4",
+						      out_parents,
+						      &ccu_div_ops,
+						      0),
+	},
+};
+
+static const struct clk_parent_data apb_parents[] = {
+	{ .hw = &gmac_pll_clk.common.hw },
+	{ .index = 0 },
+};
+
+static struct ccu_div apb_pclk = {
+	.enable		= BIT(5),
+	.div		= TH_CCU_DIV_FLAGS(0, 4, CLK_DIVIDER_ONE_BASED),
+	.mux		= TH_CCU_ARG(7, 1),
+	.common		= {
+		.clkid          = CLK_APB_PCLK,
+		.cfg0		= 0x1c4,
+		.hw.init	= CLK_HW_INIT_PARENTS_DATA("apb-pclk",
+						      apb_parents,
+						      &ccu_div_ops,
+						      0),
+	},
+};
+
+static const struct clk_hw *npu_parents[] = {
+	&gmac_pll_clk.common.hw,
+	&video_pll_clk.common.hw
+};
+
+static struct ccu_div npu_clk = {
+	.enable		= BIT(4),
+	.div		= TH_CCU_DIV_FLAGS(0, 3, CLK_DIVIDER_ONE_BASED),
+	.mux		= TH_CCU_ARG(6, 1),
+	.common		= {
+		.clkid          = CLK_NPU,
+		.cfg0		= 0x1c8,
+		.hw.init	= CLK_HW_INIT_PARENTS_HW("npu",
+						      npu_parents,
+						      &ccu_div_ops,
+						      0),
+	},
+};
+
+static struct ccu_div vi_clk = {
+	.div		= TH_CCU_DIV_FLAGS(16, 4, CLK_DIVIDER_ONE_BASED),
+	.common		= {
+		.clkid          = CLK_VI,
+		.cfg0		= 0x1d0,
+		.hw.init	= CLK_HW_INIT_PARENTS_HW("vi",
+					      video_pll_clk_parent,
+					      &ccu_div_ops,
+					      0),
+	},
+};
+
+static struct ccu_div vi_ahb_clk = {
+	.div		= TH_CCU_DIV_FLAGS(0, 4, CLK_DIVIDER_ONE_BASED),
+	.common		= {
+		.clkid          = CLK_VI_AHB,
+		.cfg0		= 0x1d0,
+		.hw.init	= CLK_HW_INIT_PARENTS_HW("vi-ahb",
+					      video_pll_clk_parent,
+					      &ccu_div_ops,
+					      0),
+	},
+};
+
+static struct ccu_div vo_axi_clk = {
+	.enable		= BIT(5),
+	.div		= TH_CCU_DIV_FLAGS(0, 4, CLK_DIVIDER_ONE_BASED),
+	.common		= {
+		.clkid          = CLK_VO_AXI,
+		.cfg0		= 0x1dc,
+		.hw.init	= CLK_HW_INIT_PARENTS_HW("vo-axi",
+					      video_pll_clk_parent,
+					      &ccu_div_ops,
+					      0),
+	},
+};
+
+static struct ccu_div vp_apb_clk = {
+	.div		= TH_CCU_DIV_FLAGS(0, 3, CLK_DIVIDER_ONE_BASED),
+	.common		= {
+		.clkid          = CLK_VP_APB,
+		.cfg0		= 0x1e0,
+		.hw.init	= CLK_HW_INIT_PARENTS_HW("vp-apb",
+					      gmac_pll_clk_parent,
+					      &ccu_div_ops,
+					      0),
+	},
+};
+
+static struct ccu_div vp_axi_clk = {
+	.enable		= BIT(15),
+	.div		= TH_CCU_DIV_FLAGS(8, 4, CLK_DIVIDER_ONE_BASED),
+	.common		= {
+		.clkid          = CLK_VP_AXI,
+		.cfg0		= 0x1e0,
+		.hw.init	= CLK_HW_INIT_PARENTS_HW("vp-axi",
+					      video_pll_clk_parent,
+					      &ccu_div_ops,
+					      0),
+	},
+};
+
+static struct ccu_div venc_clk = {
+	.enable		= BIT(5),
+	.div		= TH_CCU_DIV_FLAGS(0, 3, CLK_DIVIDER_ONE_BASED),
+	.common		= {
+		.clkid          = CLK_VENC,
+		.cfg0		= 0x1e4,
+		.hw.init	= CLK_HW_INIT_PARENTS_HW("venc",
+					      gmac_pll_clk_parent,
+					      &ccu_div_ops,
+					      0),
+	},
+};
+
+static struct ccu_div dpu0_clk = {
+	.div		= TH_CCU_DIV_FLAGS(0, 8, CLK_DIVIDER_ONE_BASED),
+	.common		= {
+		.clkid          = CLK_DPU0,
+		.cfg0		= 0x1e8,
+		.hw.init	= CLK_HW_INIT_PARENTS_HW("dpu0",
+					      dpu0_pll_clk_parent,
+					      &ccu_div_ops,
+					      0),
+	},
+};
+
+static struct ccu_div dpu1_clk = {
+	.div		= TH_CCU_DIV_FLAGS(0, 8, CLK_DIVIDER_ONE_BASED),
+	.common		= {
+		.clkid          = CLK_DPU1,
+		.cfg0		= 0x1ec,
+		.hw.init	= CLK_HW_INIT_PARENTS_HW("dpu1",
+					      dpu1_pll_clk_parent,
+					      &ccu_div_ops,
+					      0),
+	},
+};
+
+static CCU_GATE(CLK_BROM, brom_clk, "brom", ahb2_cpusys_hclk_pd, 0x100, BIT(4), 0);
+static CCU_GATE(CLK_BMU, bmu_clk, "bmu", axi4_cpusys2_aclk_pd, 0x100, BIT(5), 0);
+static CCU_GATE(CLK_AON2CPU_A2X, aon2cpu_a2x_clk, "aon2cpu-a2x", axi4_cpusys2_aclk_pd,
+		0x134, BIT(8), 0);
+static CCU_GATE(CLK_X2X_CPUSYS, x2x_cpusys_clk, "x2x-cpusys", axi4_cpusys2_aclk_pd,
+		0x134, BIT(7), 0);
+static CCU_GATE(CLK_CPU2AON_X2H, cpu2aon_x2h_clk, "cpu2aon-x2h", axi_aclk_pd, 0x138, BIT(8), 0);
+static CCU_GATE(CLK_CPU2PERI_X2H, cpu2peri_x2h_clk, "cpu2peri-x2h", axi4_cpusys2_aclk_pd,
+		0x140, BIT(9), 0);
+static CCU_GATE(CLK_PERISYS_APB1_HCLK, perisys_apb1_hclk, "perisys-apb1-hclk", perisys_ahb_hclk_pd,
+		0x150, BIT(9), 0);
+static CCU_GATE(CLK_PERISYS_APB2_HCLK, perisys_apb2_hclk, "perisys-apb2-hclk", perisys_ahb_hclk_pd,
+		0x150, BIT(10), 0);
+static CCU_GATE(CLK_PERISYS_APB3_HCLK, perisys_apb3_hclk, "perisys-apb3-hclk", perisys_ahb_hclk_pd,
+		0x150, BIT(11), 0);
+static CCU_GATE(CLK_PERISYS_APB4_HCLK, perisys_apb4_hclk, "perisys-apb4-hclk", perisys_ahb_hclk_pd,
+		0x150, BIT(12), 0);
+static CCU_GATE(CLK_NPU_AXI, npu_axi_clk, "npu-axi", axi_aclk_pd, 0x1c8, BIT(5), 0);
+static CCU_GATE(CLK_CPU2VP, cpu2vp_clk, "cpu2vp", axi_aclk_pd, 0x1e0, BIT(13), 0);
+static CCU_GATE(CLK_EMMC_SDIO, emmc_sdio_clk, "emmc-sdio", video_pll_clk_pd, 0x204, BIT(30), 0);
+static CCU_GATE(CLK_GMAC1, gmac1_clk, "gmac1", gmac_pll_clk_pd, 0x204, BIT(26), 0);
+static CCU_GATE(CLK_PADCTRL1, padctrl1_clk, "padctrl1", perisys_apb_pclk_pd, 0x204, BIT(24), 0);
+static CCU_GATE(CLK_DSMART, dsmart_clk, "dsmart", perisys_apb_pclk_pd, 0x204, BIT(23), 0);
+static CCU_GATE(CLK_PADCTRL0, padctrl0_clk, "padctrl0", perisys_apb_pclk_pd, 0x204, BIT(22), 0);
+static CCU_GATE(CLK_GMAC_AXI, gmac_axi_clk, "gmac-axi", axi4_cpusys2_aclk_pd, 0x204, BIT(21), 0);
+static CCU_GATE(CLK_GPIO3, gpio3_clk, "gpio3-clk", peri2sys_apb_pclk_pd, 0x204, BIT(20), 0);
+static CCU_GATE(CLK_GMAC0, gmac0_clk, "gmac0", gmac_pll_clk_pd, 0x204, BIT(19), 0);
+static CCU_GATE(CLK_PWM, pwm_clk, "pwm", perisys_apb_pclk_pd, 0x204, BIT(18), 0);
+static CCU_GATE(CLK_QSPI0, qspi0_clk, "qspi0", video_pll_clk_pd, 0x204, BIT(17), 0);
+static CCU_GATE(CLK_QSPI1, qspi1_clk, "qspi1", video_pll_clk_pd, 0x204, BIT(16), 0);
+static CCU_GATE(CLK_SPI, spi_clk, "spi", video_pll_clk_pd, 0x204, BIT(15), 0);
+static CCU_GATE(CLK_UART0_PCLK, uart0_pclk, "uart0-pclk", perisys_apb_pclk_pd, 0x204, BIT(14), 0);
+static CCU_GATE(CLK_UART1_PCLK, uart1_pclk, "uart1-pclk", perisys_apb_pclk_pd, 0x204, BIT(13), 0);
+static CCU_GATE(CLK_UART2_PCLK, uart2_pclk, "uart2-pclk", perisys_apb_pclk_pd, 0x204, BIT(12), 0);
+static CCU_GATE(CLK_UART3_PCLK, uart3_pclk, "uart3-pclk", perisys_apb_pclk_pd, 0x204, BIT(11), 0);
+static CCU_GATE(CLK_UART4_PCLK, uart4_pclk, "uart4-pclk", perisys_apb_pclk_pd, 0x204, BIT(10), 0);
+static CCU_GATE(CLK_UART5_PCLK, uart5_pclk, "uart5-pclk", perisys_apb_pclk_pd, 0x204, BIT(9), 0);
+static CCU_GATE(CLK_GPIO0, gpio0_clk, "gpio0-clk", perisys_apb_pclk_pd, 0x204, BIT(8), 0);
+static CCU_GATE(CLK_GPIO1, gpio1_clk, "gpio1-clk", perisys_apb_pclk_pd, 0x204, BIT(7), 0);
+static CCU_GATE(CLK_GPIO2, gpio2_clk, "gpio2-clk", peri2sys_apb_pclk_pd, 0x204, BIT(6), 0);
+static CCU_GATE(CLK_I2C0, i2c0_clk, "i2c0", perisys_apb_pclk_pd, 0x204, BIT(5), 0);
+static CCU_GATE(CLK_I2C1, i2c1_clk, "i2c1", perisys_apb_pclk_pd, 0x204, BIT(4), 0);
+static CCU_GATE(CLK_I2C2, i2c2_clk, "i2c2", perisys_apb_pclk_pd, 0x204, BIT(3), 0);
+static CCU_GATE(CLK_I2C3, i2c3_clk, "i2c3", perisys_apb_pclk_pd, 0x204, BIT(2), 0);
+static CCU_GATE(CLK_I2C4, i2c4_clk, "i2c4", perisys_apb_pclk_pd, 0x204, BIT(1), 0);
+static CCU_GATE(CLK_I2C5, i2c5_clk, "i2c5", perisys_apb_pclk_pd, 0x204, BIT(0), 0);
+static CCU_GATE(CLK_SPINLOCK, spinlock_clk, "spinlock", ahb2_cpusys_hclk_pd, 0x208, BIT(10), 0);
+static CCU_GATE(CLK_DMA, dma_clk, "dma", axi4_cpusys2_aclk_pd, 0x208, BIT(8), 0);
+static CCU_GATE(CLK_MBOX0, mbox0_clk, "mbox0", apb3_cpusys_pclk_pd, 0x208, BIT(7), 0);
+static CCU_GATE(CLK_MBOX1, mbox1_clk, "mbox1", apb3_cpusys_pclk_pd, 0x208, BIT(6), 0);
+static CCU_GATE(CLK_MBOX2, mbox2_clk, "mbox2", apb3_cpusys_pclk_pd, 0x208, BIT(5), 0);
+static CCU_GATE(CLK_MBOX3, mbox3_clk, "mbox3", apb3_cpusys_pclk_pd, 0x208, BIT(4), 0);
+static CCU_GATE(CLK_WDT0, wdt0_clk, "wdt0", apb3_cpusys_pclk_pd, 0x208, BIT(3), 0);
+static CCU_GATE(CLK_WDT1, wdt1_clk, "wdt1", apb3_cpusys_pclk_pd, 0x208, BIT(2), 0);
+static CCU_GATE(CLK_TIMER0, timer0_clk, "timer0", apb3_cpusys_pclk_pd, 0x208, BIT(1), 0);
+static CCU_GATE(CLK_TIMER1, timer1_clk, "timer1", apb3_cpusys_pclk_pd, 0x208, BIT(0), 0);
+static CCU_GATE(CLK_SRAM0, sram0_clk, "sram0", axi_aclk_pd, 0x20c, BIT(4), 0);
+static CCU_GATE(CLK_SRAM1, sram1_clk, "sram1", axi_aclk_pd, 0x20c, BIT(3), 0);
+static CCU_GATE(CLK_SRAM2, sram2_clk, "sram2", axi_aclk_pd, 0x20c, BIT(2), 0);
+static CCU_GATE(CLK_SRAM3, sram3_clk, "sram3", axi_aclk_pd, 0x20c, BIT(1), 0);
+
+static CLK_FIXED_FACTOR_HW(gmac_pll_clk_100m, "gmac-pll-clk-100m",
+			   &gmac_pll_clk.common.hw, 10, 1, 0);
+
+static const struct clk_parent_data uart_sclk_parents[] = {
+	{ .hw = &gmac_pll_clk_100m.hw },
+	{ .index = 0 },
+};
+
+struct ccu_mux uart_sclk = {
+	.mux	= TH_CCU_ARG(0, 1),
+	.common	= {
+		.clkid          = CLK_UART_SCLK,
+		.cfg0		= 0x210,
+		.hw.init	= CLK_HW_INIT_PARENTS_DATA("uart-sclk",
+					      uart_sclk_parents,
+					      &clk_mux_ops,
+					      0),
+	}
+};
+
+static struct ccu_common *th1520_pll_clks[] = {
+	&cpu_pll0_clk.common,
+	&cpu_pll1_clk.common,
+	&gmac_pll_clk.common,
+	&video_pll_clk.common,
+	&dpu0_pll_clk.common,
+	&dpu1_pll_clk.common,
+	&tee_pll_clk.common,
+};
+
+static struct ccu_common *th1520_div_clks[] = {
+	&ahb2_cpusys_hclk.common,
+	&apb3_cpusys_pclk.common,
+	&axi4_cpusys2_aclk.common,
+	&perisys_ahb_hclk.common,
+	&perisys_apb_pclk.common,
+	&axi_aclk.common,
+	&peri2sys_apb_pclk.common,
+	&out1_clk.common,
+	&out2_clk.common,
+	&out3_clk.common,
+	&out4_clk.common,
+	&apb_pclk.common,
+	&npu_clk.common,
+	&vi_clk.common,
+	&vi_ahb_clk.common,
+	&vo_axi_clk.common,
+	&vp_apb_clk.common,
+	&vp_axi_clk.common,
+	&cpu2vp_clk.common,
+	&venc_clk.common,
+	&dpu0_clk.common,
+	&dpu1_clk.common,
+};
+
+static struct ccu_common *th1520_mux_clks[] = {
+	&c910_i0_clk.common,
+	&c910_clk.common,
+	&uart_sclk.common,
+};
+
+static struct ccu_common *th1520_gate_clks[] = {
+	&emmc_sdio_clk.common,
+	&aon2cpu_a2x_clk.common,
+	&x2x_cpusys_clk.common,
+	&brom_clk.common,
+	&bmu_clk.common,
+	&cpu2aon_x2h_clk.common,
+	&cpu2peri_x2h_clk.common,
+	&perisys_apb1_hclk.common,
+	&perisys_apb2_hclk.common,
+	&perisys_apb3_hclk.common,
+	&perisys_apb4_hclk.common,
+	&npu_axi_clk.common,
+	&gmac1_clk.common,
+	&padctrl1_clk.common,
+	&dsmart_clk.common,
+	&padctrl0_clk.common,
+	&gmac_axi_clk.common,
+	&gpio3_clk.common,
+	&gmac0_clk.common,
+	&pwm_clk.common,
+	&qspi0_clk.common,
+	&qspi1_clk.common,
+	&spi_clk.common,
+	&uart0_pclk.common,
+	&uart1_pclk.common,
+	&uart2_pclk.common,
+	&uart3_pclk.common,
+	&uart4_pclk.common,
+	&uart5_pclk.common,
+	&gpio0_clk.common,
+	&gpio1_clk.common,
+	&gpio2_clk.common,
+	&i2c0_clk.common,
+	&i2c1_clk.common,
+	&i2c2_clk.common,
+	&i2c3_clk.common,
+	&i2c4_clk.common,
+	&i2c5_clk.common,
+	&spinlock_clk.common,
+	&dma_clk.common,
+	&mbox0_clk.common,
+	&mbox1_clk.common,
+	&mbox2_clk.common,
+	&mbox3_clk.common,
+	&wdt0_clk.common,
+	&wdt1_clk.common,
+	&timer0_clk.common,
+	&timer1_clk.common,
+	&sram0_clk.common,
+	&sram1_clk.common,
+	&sram2_clk.common,
+	&sram3_clk.common,
+};
+
+#define NR_CLKS	(CLK_UART_SCLK + 1)
+
+static const struct regmap_config th1520_clk_regmap_config = {
+	.reg_bits = 32,
+	.val_bits = 32,
+	.reg_stride = 4,
+	.fast_io = true,
+};
+
+static int th1520_clk_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct clk_hw_onecell_data *priv;
+
+	struct regmap *map;
+	void __iomem *base;
+	struct clk_hw *hw;
+	int ret, i;
+
+	priv = devm_kzalloc(dev, struct_size(priv, hws, NR_CLKS), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->num = NR_CLKS;
+
+	base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	map = devm_regmap_init_mmio(dev, base, &th1520_clk_regmap_config);
+	if (IS_ERR(map))
+		return PTR_ERR(map);
+
+	for (i = 0; i < ARRAY_SIZE(th1520_pll_clks); i++) {
+		struct ccu_pll *cp = hw_to_ccu_pll(&th1520_pll_clks[i]->hw);
+
+		th1520_pll_clks[i]->map = map;
+
+		ret = devm_clk_hw_register(dev, &th1520_pll_clks[i]->hw);
+		if (ret)
+			return ret;
+
+		priv->hws[cp->common.clkid] = &cp->common.hw;
+	}
+
+	for (i = 0; i < ARRAY_SIZE(th1520_div_clks); i++) {
+		struct ccu_div *cd = hw_to_ccu_div(&th1520_div_clks[i]->hw);
+
+		th1520_div_clks[i]->map = map;
+
+		ret = devm_clk_hw_register(dev, &th1520_div_clks[i]->hw);
+		if (ret)
+			return ret;
+
+		priv->hws[cd->common.clkid] = &cd->common.hw;
+	}
+
+	for (i = 0; i < ARRAY_SIZE(th1520_mux_clks); i++) {
+		struct ccu_mux *cm = hw_to_ccu_mux(&th1520_mux_clks[i]->hw);
+		const struct clk_init_data *init = cm->common.hw.init;
+
+		th1520_mux_clks[i]->map = map;
+		hw = devm_clk_hw_register_mux_parent_data_table(dev,
+								init->name,
+								init->parent_data,
+								init->num_parents,
+								0,
+								base + cm->common.cfg0,
+								cm->mux.shift,
+								cm->mux.width,
+								0, NULL, NULL);
+		if (IS_ERR(hw))
+			return PTR_ERR(hw);
+
+		priv->hws[cm->common.clkid] = hw;
+	}
+
+	for (i = 0; i < ARRAY_SIZE(th1520_gate_clks); i++) {
+		struct ccu_gate *cg = hw_to_ccu_gate(&th1520_gate_clks[i]->hw);
+
+		th1520_gate_clks[i]->map = map;
+
+		hw = devm_clk_hw_register_gate_parent_data(dev,
+							   cg->common.hw.init->name,
+							   cg->common.hw.init->parent_data,
+							   0, base + cg->common.cfg0,
+							   ffs(cg->enable) - 1, 0, NULL);
+		if (IS_ERR(hw))
+			return PTR_ERR(hw);
+
+		priv->hws[cg->common.clkid] = hw;
+	}
+
+	ret = devm_clk_hw_register(dev, &osc12m_clk.hw);
+	if (ret)
+		return ret;
+	priv->hws[CLK_OSC12M] = &osc12m_clk.hw;
+
+	ret = devm_clk_hw_register(dev, &gmac_pll_clk_100m.hw);
+	if (ret)
+		return ret;
+	priv->hws[CLK_PLL_GMAC_100M] = &gmac_pll_clk_100m.hw;
+
+	ret = devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get, priv);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static const struct of_device_id th1520_clk_match[] = {
+	{
+		.compatible = "thead,th1520-clk-ap",
+	},
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, th1520_clk_match);
+
+static struct platform_driver th1520_clk_driver = {
+	.probe		= th1520_clk_probe,
+	.driver		= {
+		.name	= "th1520-clk",
+		.of_match_table = th1520_clk_match,
+	},
+};
+module_platform_driver(th1520_clk_driver);
+
+MODULE_DESCRIPTION("T-HEAD TH1520 AP Clock driver");
+MODULE_AUTHOR("Yangtao Li <frank.li@vivo.com>");
+MODULE_AUTHOR("Jisheng Zhang <jszhang@kernel.org>");
+MODULE_LICENSE("GPL");

-- 
2.34.1

[PATCH v3 3/7] riscv: dts: thead: Add TH1520 AP_SUBSYS clock controller

[Drew Fustini]

Add node for the AP_SUBSYS clock controller on the T-Head TH1520 SoC.

Link: https://openbeagle.org/beaglev-ahead/beaglev-ahead/-/blob/main/docs/TH1520%20System%20User%20Manual.pdf
Link: https://git.beagleboard.org/beaglev-ahead/beaglev-ahead/-/tree/main/docs
Signed-off-by: Drew Fustini <dfustini@tenstorrent.com>
---
 arch/riscv/boot/dts/thead/th1520.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/riscv/boot/dts/thead/th1520.dtsi b/arch/riscv/boot/dts/thead/th1520.dtsi
index d2fa25839012..10a38ed55658 100644
--- a/arch/riscv/boot/dts/thead/th1520.dtsi
+++ b/arch/riscv/boot/dts/thead/th1520.dtsi
@@ -5,6 +5,7 @@
  */
 
 #include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/clock/thead,th1520-clk-ap.h>
 
 / {
 	compatible = "thead,th1520";
@@ -161,6 +162,13 @@ soc {
 		dma-noncoherent;
 		ranges;
 
+		clk: clock-controller@ffef010000 {
+			compatible = "thead,th1520-clk-ap";
+			reg = <0xff 0xef010000 0x0 0x1000>;
+			clocks = <&osc>;
+			#clock-cells = <1>;
+		};
+
 		plic: interrupt-controller@ffd8000000 {
 			compatible = "thead,th1520-plic", "thead,c900-plic";
 			reg = <0xff 0xd8000000 0x0 0x01000000>;

-- 
2.34.1

[PATCH v3 4/7] riscv: dts: thead: change TH1520 uart nodes to use clock controller

[Drew Fustini]

Change the clock property in TH1520 uart nodes to a clock provided by
AP_SUBSYS clock controller.

Link: https://git.beagleboard.org/beaglev-ahead/beaglev-ahead/-/tree/main/docs
Signed-off-by: Drew Fustini <dfustini@tenstorrent.com>
---
 arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts |  4 ----
 .../boot/dts/thead/th1520-lichee-module-4a.dtsi    |  4 ----
 arch/riscv/boot/dts/thead/th1520.dtsi              | 24 +++++++++++-----------
 3 files changed, 12 insertions(+), 20 deletions(-)

diff --git a/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts b/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts
index d9b4de9e4757..164afd18b56c 100644
--- a/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts
+++ b/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts
@@ -52,10 +52,6 @@ &sdhci_clk {
 	clock-frequency = <198000000>;
 };
 
-&uart_sclk {
-	clock-frequency = <100000000>;
-};
-
 &dmac0 {
 	status = "okay";
 };
diff --git a/arch/riscv/boot/dts/thead/th1520-lichee-module-4a.dtsi b/arch/riscv/boot/dts/thead/th1520-lichee-module-4a.dtsi
index 1365d3a512a3..1b7ede570994 100644
--- a/arch/riscv/boot/dts/thead/th1520-lichee-module-4a.dtsi
+++ b/arch/riscv/boot/dts/thead/th1520-lichee-module-4a.dtsi
@@ -33,10 +33,6 @@ &sdhci_clk {
 	clock-frequency = <198000000>;
 };
 
-&uart_sclk {
-	clock-frequency = <100000000>;
-};
-
 &dmac0 {
 	status = "okay";
 };
diff --git a/arch/riscv/boot/dts/thead/th1520.dtsi b/arch/riscv/boot/dts/thead/th1520.dtsi
index 10a38ed55658..66df04ceb3e4 100644
--- a/arch/riscv/boot/dts/thead/th1520.dtsi
+++ b/arch/riscv/boot/dts/thead/th1520.dtsi
@@ -141,12 +141,6 @@ apb_clk: apb-clk-clock {
 		#clock-cells = <0>;
 	};
 
-	uart_sclk: uart-sclk-clock {
-		compatible = "fixed-clock";
-		clock-output-names = "uart_sclk";
-		#clock-cells = <0>;
-	};
-
 	sdhci_clk: sdhci-clock {
 		compatible = "fixed-clock";
 		clock-frequency = <198000000>;
@@ -195,7 +189,8 @@ uart0: serial@ffe7014000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0xff 0xe7014000 0x0 0x100>;
 			interrupts = <36 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&uart_sclk>;
+			clocks = <&clk CLK_UART_SCLK>, <&clk CLK_UART0_PCLK>;
+			clock-names = "baudclk", "apb_pclk";
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			status = "disabled";
@@ -232,7 +227,8 @@ uart1: serial@ffe7f00000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0xff 0xe7f00000 0x0 0x100>;
 			interrupts = <37 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&uart_sclk>;
+			clocks = <&clk CLK_UART_SCLK>, <&clk CLK_UART1_PCLK>;
+			clock-names = "baudclk", "apb_pclk";
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			status = "disabled";
@@ -242,7 +238,8 @@ uart3: serial@ffe7f04000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0xff 0xe7f04000 0x0 0x100>;
 			interrupts = <39 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&uart_sclk>;
+			clocks = <&clk CLK_UART_SCLK>, <&clk CLK_UART3_PCLK>;
+			clock-names = "baudclk", "apb_pclk";
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			status = "disabled";
@@ -324,7 +321,8 @@ uart2: serial@ffec010000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0xff 0xec010000 0x0 0x4000>;
 			interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&uart_sclk>;
+			clocks = <&clk CLK_UART_SCLK>, <&clk CLK_UART2_PCLK>;
+			clock-names = "baudclk", "apb_pclk";
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			status = "disabled";
@@ -386,7 +384,8 @@ uart4: serial@fff7f08000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0xff 0xf7f08000 0x0 0x4000>;
 			interrupts = <40 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&uart_sclk>;
+			clocks = <&clk CLK_UART_SCLK>, <&clk CLK_UART4_PCLK>;
+			clock-names = "baudclk", "apb_pclk";
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			status = "disabled";
@@ -396,7 +395,8 @@ uart5: serial@fff7f0c000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0xff 0xf7f0c000 0x0 0x4000>;
 			interrupts = <41 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&uart_sclk>;
+			clocks = <&clk CLK_UART_SCLK>, <&clk CLK_UART5_PCLK>;
+			clock-names = "baudclk", "apb_pclk";
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			status = "disabled";

-- 
2.34.1

[PATCH v3 5/7] riscv: dts: thead: change TH1520 mmc nodes to use clock controller

[Drew Fustini]

Change the clock property in the TH1520 mmc controller nodes to a clock
provided by AP_SYS clock controller.

Remove sdhci fixed clock reference from BeagleV Ahead and LPI4a dts.

Link: https://git.beagleboard.org/beaglev-ahead/beaglev-ahead/-/tree/main/docs
Signed-off-by: Drew Fustini <dfustini@tenstorrent.com>
---
 arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts     |  4 ----
 arch/riscv/boot/dts/thead/th1520-lichee-module-4a.dtsi |  4 ----
 arch/riscv/boot/dts/thead/th1520.dtsi                  | 13 +++----------
 3 files changed, 3 insertions(+), 18 deletions(-)

diff --git a/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts b/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts
index 164afd18b56c..55f1ed0cb433 100644
--- a/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts
+++ b/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts
@@ -48,10 +48,6 @@ &apb_clk {
 	clock-frequency = <62500000>;
 };
 
-&sdhci_clk {
-	clock-frequency = <198000000>;
-};
-
 &dmac0 {
 	status = "okay";
 };
diff --git a/arch/riscv/boot/dts/thead/th1520-lichee-module-4a.dtsi b/arch/riscv/boot/dts/thead/th1520-lichee-module-4a.dtsi
index 1b7ede570994..762eceb415f8 100644
--- a/arch/riscv/boot/dts/thead/th1520-lichee-module-4a.dtsi
+++ b/arch/riscv/boot/dts/thead/th1520-lichee-module-4a.dtsi
@@ -29,10 +29,6 @@ &apb_clk {
 	clock-frequency = <62500000>;
 };
 
-&sdhci_clk {
-	clock-frequency = <198000000>;
-};
-
 &dmac0 {
 	status = "okay";
 };
diff --git a/arch/riscv/boot/dts/thead/th1520.dtsi b/arch/riscv/boot/dts/thead/th1520.dtsi
index 66df04ceb3e4..ce3a0847aa9c 100644
--- a/arch/riscv/boot/dts/thead/th1520.dtsi
+++ b/arch/riscv/boot/dts/thead/th1520.dtsi
@@ -141,13 +141,6 @@ apb_clk: apb-clk-clock {
 		#clock-cells = <0>;
 	};
 
-	sdhci_clk: sdhci-clock {
-		compatible = "fixed-clock";
-		clock-frequency = <198000000>;
-		clock-output-names = "sdhci_clk";
-		#clock-cells = <0>;
-	};
-
 	soc {
 		compatible = "simple-bus";
 		interrupt-parent = <&plic>;
@@ -200,7 +193,7 @@ emmc: mmc@ffe7080000 {
 			compatible = "thead,th1520-dwcmshc";
 			reg = <0xff 0xe7080000 0x0 0x10000>;
 			interrupts = <62 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&sdhci_clk>;
+			clocks = <&clk CLK_EMMC_SDIO>;
 			clock-names = "core";
 			status = "disabled";
 		};
@@ -209,7 +202,7 @@ sdio0: mmc@ffe7090000 {
 			compatible = "thead,th1520-dwcmshc";
 			reg = <0xff 0xe7090000 0x0 0x10000>;
 			interrupts = <64 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&sdhci_clk>;
+			clocks = <&clk CLK_EMMC_SDIO>;
 			clock-names = "core";
 			status = "disabled";
 		};
@@ -218,7 +211,7 @@ sdio1: mmc@ffe70a0000 {
 			compatible = "thead,th1520-dwcmshc";
 			reg = <0xff 0xe70a0000 0x0 0x10000>;
 			interrupts = <71 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&sdhci_clk>;
+			clocks = <&clk CLK_EMMC_SDIO>;
 			clock-names = "core";
 			status = "disabled";
 		};

-- 
2.34.1

[PATCH v3 6/7] riscv: dts: thead: update TH1520 dma and timer nodes to use clock controller

[Drew Fustini]

Change the dma-controller and timer nodes to use the APB clock provided
by the AP_SUBSYS clock controller.

Remove apb_clk reference from BeagleV Ahead and LPI4a dts.

Link: https://git.beagleboard.org/beaglev-ahead/beaglev-ahead/-/tree/main/docs
Signed-off-by: Drew Fustini <dfustini@tenstorrent.com>
---
 arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts |  4 ----
 .../boot/dts/thead/th1520-lichee-module-4a.dtsi    |  4 ----
 arch/riscv/boot/dts/thead/th1520.dtsi              | 24 ++++++++--------------
 3 files changed, 9 insertions(+), 23 deletions(-)

diff --git a/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts b/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts
index 55f1ed0cb433..1180e41c7b07 100644
--- a/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts
+++ b/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts
@@ -44,10 +44,6 @@ &osc_32k {
 	clock-frequency = <32768>;
 };
 
-&apb_clk {
-	clock-frequency = <62500000>;
-};
-
 &dmac0 {
 	status = "okay";
 };
diff --git a/arch/riscv/boot/dts/thead/th1520-lichee-module-4a.dtsi b/arch/riscv/boot/dts/thead/th1520-lichee-module-4a.dtsi
index 762eceb415f8..78977bdbbe3d 100644
--- a/arch/riscv/boot/dts/thead/th1520-lichee-module-4a.dtsi
+++ b/arch/riscv/boot/dts/thead/th1520-lichee-module-4a.dtsi
@@ -25,10 +25,6 @@ &osc_32k {
 	clock-frequency = <32768>;
 };
 
-&apb_clk {
-	clock-frequency = <62500000>;
-};
-
 &dmac0 {
 	status = "okay";
 };
diff --git a/arch/riscv/boot/dts/thead/th1520.dtsi b/arch/riscv/boot/dts/thead/th1520.dtsi
index ce3a0847aa9c..d05002ad7c96 100644
--- a/arch/riscv/boot/dts/thead/th1520.dtsi
+++ b/arch/riscv/boot/dts/thead/th1520.dtsi
@@ -135,12 +135,6 @@ osc_32k: 32k-oscillator {
 		#clock-cells = <0>;
 	};
 
-	apb_clk: apb-clk-clock {
-		compatible = "fixed-clock";
-		clock-output-names = "apb_clk";
-		#clock-cells = <0>;
-	};
-
 	soc {
 		compatible = "simple-bus";
 		interrupt-parent = <&plic>;
@@ -325,7 +319,7 @@ dmac0: dma-controller@ffefc00000 {
 			compatible = "snps,axi-dma-1.01a";
 			reg = <0xff 0xefc00000 0x0 0x1000>;
 			interrupts = <27 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&apb_clk>, <&apb_clk>;
+			clocks = <&clk CLK_PERI_APB_PCLK>, <&clk CLK_PERI_APB_PCLK>;
 			clock-names = "core-clk", "cfgr-clk";
 			#dma-cells = <1>;
 			dma-channels = <4>;
@@ -340,7 +334,7 @@ dmac0: dma-controller@ffefc00000 {
 		timer0: timer@ffefc32000 {
 			compatible = "snps,dw-apb-timer";
 			reg = <0xff 0xefc32000 0x0 0x14>;
-			clocks = <&apb_clk>;
+			clocks = <&clk CLK_PERI_APB_PCLK>;
 			clock-names = "timer";
 			interrupts = <16 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
@@ -349,7 +343,7 @@ timer0: timer@ffefc32000 {
 		timer1: timer@ffefc32014 {
 			compatible = "snps,dw-apb-timer";
 			reg = <0xff 0xefc32014 0x0 0x14>;
-			clocks = <&apb_clk>;
+			clocks = <&clk CLK_PERI_APB_PCLK>;
 			clock-names = "timer";
 			interrupts = <17 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
@@ -358,7 +352,7 @@ timer1: timer@ffefc32014 {
 		timer2: timer@ffefc32028 {
 			compatible = "snps,dw-apb-timer";
 			reg = <0xff 0xefc32028 0x0 0x14>;
-			clocks = <&apb_clk>;
+			clocks = <&clk CLK_PERI_APB_PCLK>;
 			clock-names = "timer";
 			interrupts = <18 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
@@ -367,7 +361,7 @@ timer2: timer@ffefc32028 {
 		timer3: timer@ffefc3203c {
 			compatible = "snps,dw-apb-timer";
 			reg = <0xff 0xefc3203c 0x0 0x14>;
-			clocks = <&apb_clk>;
+			clocks = <&clk CLK_PERI_APB_PCLK>;
 			clock-names = "timer";
 			interrupts = <19 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
@@ -398,7 +392,7 @@ uart5: serial@fff7f0c000 {
 		timer4: timer@ffffc33000 {
 			compatible = "snps,dw-apb-timer";
 			reg = <0xff 0xffc33000 0x0 0x14>;
-			clocks = <&apb_clk>;
+			clocks = <&clk CLK_PERI_APB_PCLK>;
 			clock-names = "timer";
 			interrupts = <20 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
@@ -407,7 +401,7 @@ timer4: timer@ffffc33000 {
 		timer5: timer@ffffc33014 {
 			compatible = "snps,dw-apb-timer";
 			reg = <0xff 0xffc33014 0x0 0x14>;
-			clocks = <&apb_clk>;
+			clocks = <&clk CLK_PERI_APB_PCLK>;
 			clock-names = "timer";
 			interrupts = <21 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
@@ -416,7 +410,7 @@ timer5: timer@ffffc33014 {
 		timer6: timer@ffffc33028 {
 			compatible = "snps,dw-apb-timer";
 			reg = <0xff 0xffc33028 0x0 0x14>;
-			clocks = <&apb_clk>;
+			clocks = <&clk CLK_PERI_APB_PCLK>;
 			clock-names = "timer";
 			interrupts = <22 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
@@ -425,7 +419,7 @@ timer6: timer@ffffc33028 {
 		timer7: timer@ffffc3303c {
 			compatible = "snps,dw-apb-timer";
 			reg = <0xff 0xffc3303c 0x0 0x14>;
-			clocks = <&apb_clk>;
+			clocks = <&clk CLK_PERI_APB_PCLK>;
 			clock-names = "timer";
 			interrupts = <23 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";

-- 
2.34.1

[PATCH v3 7/7] riscv: dts: thead: add clock to TH1520 gpio nodes

[Drew Fustini]

Add clock property to TH1520 gpio controller nodes. These clock gates
refer to corresponding enable bits in the peripheral clock gate control
register. Refer to register PERI_CLK_CFG in section 4.4.2.2.52 of the
TH1520 System User Manual.

Link: https://git.beagleboard.org/beaglev-ahead/beaglev-ahead/-/tree/main/docs
Signed-off-by: Drew Fustini <dfustini@tenstorrent.com>
---
 arch/riscv/boot/dts/thead/th1520.dtsi | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/riscv/boot/dts/thead/th1520.dtsi b/arch/riscv/boot/dts/thead/th1520.dtsi
index d05002ad7c96..351e09beab70 100644
--- a/arch/riscv/boot/dts/thead/th1520.dtsi
+++ b/arch/riscv/boot/dts/thead/th1520.dtsi
@@ -237,6 +237,7 @@ gpio2: gpio@ffe7f34000 {
 			reg = <0xff 0xe7f34000 0x0 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clocks = <&clk CLK_GPIO2>;
 
 			portc: gpio-controller@0 {
 				compatible = "snps,dw-apb-gpio-port";
@@ -255,6 +256,7 @@ gpio3: gpio@ffe7f38000 {
 			reg = <0xff 0xe7f38000 0x0 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clocks = <&clk CLK_GPIO3>;
 
 			portd: gpio-controller@0 {
 				compatible = "snps,dw-apb-gpio-port";
@@ -273,6 +275,7 @@ gpio0: gpio@ffec005000 {
 			reg = <0xff 0xec005000 0x0 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clocks = <&clk CLK_GPIO0>;
 
 			porta: gpio-controller@0 {
 				compatible = "snps,dw-apb-gpio-port";
@@ -291,6 +294,7 @@ gpio1: gpio@ffec006000 {
 			reg = <0xff 0xec006000 0x0 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clocks = <&clk CLK_GPIO1>;
 
 			portb: gpio-controller@0 {
 				compatible = "snps,dw-apb-gpio-port";

-- 
2.34.1

Re: [PATCH v3 0/7] clk: thead: Add support for TH1520 AP_SUBSYS clock controller

[Stephen Boyd]

Quoting Drew Fustini (2024-07-11 09:56:18)
> This series adds support for the AP sub-system clock controller in the
> T-Head TH1520 [1]. Yangtao Li originally submitted this series in May
> 2023 [2]. Jisheng made additional improvements and then passed on the
> work in progress to me.
> 
> Link: https://openbeagle.org/beaglev-ahead/beaglev-ahead/-/blob/main/docs/TH1520%20System%20User%20Manual.pdf [1]
> Link: https://lore.kernel.org/all/20230515054402.27633-1-frank.li@vivo.com/ [2]
> 
> Changes in v3:
>  - dt-binding patch has been applied to clk-next by Stephen but I'm
>    keeping it in the series for completeness.
>  - move dt-bindings include after linux includes in driver
>  - change rate to u64 in th1520_pll_vco_recalc_rate()
>  - replace do_div() with normal division operation in both
>    th1520_pll_vco_recalc_rate() and th1520_pll_postdiv_recalc_rate()
>  - add static to ccu_mux structs: c910_i0_clk, c910_clk, uart_sclk

This didn't happen, so I just did it myself.

Re: [PATCH v3 2/7] clk: thead: Add support for T-Head TH1520 AP_SUBSYS clocks

[Stephen Boyd]

Quoting Drew Fustini (2024-07-11 09:56:20)
> Add support for the AP sub-system clock controller in the T-Head TH1520.
> This include CPU, DPU, GMAC and TEE PLLs.
> 
> Link: https://openbeagle.org/beaglev-ahead/beaglev-ahead/-/blob/main/docs/TH1520%20System%20User%20Manual.pdf
> Co-developed-by: Yangtao Li <frank.li@vivo.com>
> Signed-off-by: Yangtao Li <frank.li@vivo.com>
> Co-developed-by: Jisheng Zhang <jszhang@kernel.org>
> Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
> Link: https://git.beagleboard.org/beaglev-ahead/beaglev-ahead/-/tree/main/docs
> Signed-off-by: Drew Fustini <dfustini@tenstorrent.com>
> ---

Applied to clk-next

Re: [PATCH v3 3/7] riscv: dts: thead: Add TH1520 AP_SUBSYS clock controller

[Emil Renner Berthing]

Drew Fustini wrote:
> Add node for the AP_SUBSYS clock controller on the T-Head TH1520 SoC.
>
> Link: https://openbeagle.org/beaglev-ahead/beaglev-ahead/-/blob/main/docs/TH1520%20System%20User%20Manual.pdf
> Link: https://git.beagleboard.org/beaglev-ahead/beaglev-ahead/-/tree/main/docs
> Signed-off-by: Drew Fustini <dfustini@tenstorrent.com>
> ---
>  arch/riscv/boot/dts/thead/th1520.dtsi | 8 ++++++++
>  1 file changed, 8 insertions(+)
>
> diff --git a/arch/riscv/boot/dts/thead/th1520.dtsi b/arch/riscv/boot/dts/thead/th1520.dtsi
> index d2fa25839012..10a38ed55658 100644
> --- a/arch/riscv/boot/dts/thead/th1520.dtsi
> +++ b/arch/riscv/boot/dts/thead/th1520.dtsi
> @@ -5,6 +5,7 @@
>   */
>
>  #include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/clock/thead,th1520-clk-ap.h>
>
>  / {
>  	compatible = "thead,th1520";
> @@ -161,6 +162,13 @@ soc {
>  		dma-noncoherent;
>  		ranges;
>
> +		clk: clock-controller@ffef010000 {
> +			compatible = "thead,th1520-clk-ap";
> +			reg = <0xff 0xef010000 0x0 0x1000>;
> +			clocks = <&osc>;
> +			#clock-cells = <1>;
> +		};

Please add this node so nodes are still sorted by address.

> +
>  		plic: interrupt-controller@ffd8000000 {
>  			compatible = "thead,th1520-plic", "thead,c900-plic";
>  			reg = <0xff 0xd8000000 0x0 0x01000000>;
>
> --
> 2.34.1
>
>
> _______________________________________________
> linux-riscv mailing list
> linux-riscv@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-riscv