Re: [PATCH v8 4/4] PCI: dwc: Add support for configuring lane equalization presets

[Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>]

On 3/28/2025 10:23 AM, Manivannan Sadhasivam wrote:
> On Sun, Mar 16, 2025 at 09:39:04AM +0530, Krishna Chaitanya Chundru wrote:
>> PCIe equalization presets are predefined settings used to optimize
>> signal integrity by compensating for signal loss and distortion in
>> high-speed data transmission.
>>
>> Based upon the number of lanes and the data rate supported, write
>> the preset data read from the device tree in to the lane equalization
>> control registers.
>>
>> Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
>> ---
>>   drivers/pci/controller/dwc/pcie-designware-host.c | 60 +++++++++++++++++++++++
>>   drivers/pci/controller/dwc/pcie-designware.h      |  3 ++
>>   include/uapi/linux/pci_regs.h                     |  3 ++
>>   3 files changed, 66 insertions(+)
>>
>> diff --git a/drivers/pci/controller/dwc/pcie-designware-host.c b/drivers/pci/controller/dwc/pcie-designware-host.c
>> index dd56cc02f4ef..7c6e6a74383b 100644
>> --- a/drivers/pci/controller/dwc/pcie-designware-host.c
>> +++ b/drivers/pci/controller/dwc/pcie-designware-host.c
>> @@ -507,6 +507,10 @@ int dw_pcie_host_init(struct dw_pcie_rp *pp)
>>   	if (pci->num_lanes < 1)
>>   		pci->num_lanes = dw_pcie_link_get_max_link_width(pci);
>>   
>> +	ret = of_pci_get_equalization_presets(dev, &pp->presets, pci->num_lanes);
>> +	if (ret)
>> +		goto err_free_msi;
>> +
>>   	/*
>>   	 * Allocate the resource for MSG TLP before programming the iATU
>>   	 * outbound window in dw_pcie_setup_rc(). Since the allocation depends
>> @@ -808,6 +812,61 @@ static int dw_pcie_iatu_setup(struct dw_pcie_rp *pp)
>>   	return 0;
>>   }
>>   
>> +static void dw_pcie_program_presets(struct dw_pcie_rp *pp, enum pci_bus_speed speed)
>> +{
>> +	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
>> +	u8 lane_eq_offset, lane_reg_size, cap_id;
>> +	u8 *presets;
>> +	u32 cap;
>> +	int i;
>> +
>> +	if (speed == PCIE_SPEED_8_0GT) {
>> +		presets = (u8 *)pp->presets.eq_presets_8gts;
>> +		lane_eq_offset =  PCI_SECPCI_LE_CTRL;
>> +		cap_id = PCI_EXT_CAP_ID_SECPCI;
>> +		/* For data rate of 8 GT/S each lane equalization control is 16bits wide*/
>> +		lane_reg_size = 0x2;
>> +	} else if (speed == PCIE_SPEED_16_0GT) {
>> +		presets = pp->presets.eq_presets_Ngts[EQ_PRESET_TYPE_16GTS - 1];
>> +		lane_eq_offset = PCI_PL_16GT_LE_CTRL;
>> +		cap_id = PCI_EXT_CAP_ID_PL_16GT;
>> +		lane_reg_size = 0x1;
>> +	} else {
> 
> Can you add conditions for other data rates also? Like 32, 64 GT/s. If
> controller supports them and if the presets property is defined in DT, then you
> should apply the preset values.
> 
> If the presets property is not present in DT, then below 'PCI_EQ_RESV' will
> safely return.
> 
I am fine to add it, but there is no GEN5 or GEN6 controller support
added in dwc, isn't it best to add when that support is added and
tested.

- Krishna Chaitanya.

>> +		return;
>> +	}
>> +
>> +	if (presets[0] == PCI_EQ_RESV)
>> +		return;
>> +
>> +	cap = dw_pcie_find_ext_capability(pci, cap_id);
>> +	if (!cap)
>> +		return;
>> +
>> +	/*
>> +	 * Write preset values to the registers byte-by-byte for the given
>> +	 * number of lanes and register size.
>> +	 */
>> +	for (i = 0; i < pci->num_lanes * lane_reg_size; i++)
>> +		dw_pcie_writeb_dbi(pci, cap + lane_eq_offset + i, presets[i]);
>> +}
>> +
>> +static void dw_pcie_config_presets(struct dw_pcie_rp *pp)
>> +{
>> +	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
>> +	enum pci_bus_speed speed = pcie_link_speed[pci->max_link_speed];
>> +
>> +	/*
>> +	 * Lane equalization needs to be perfomed for all data rates
>> +	 * the controller supports and for all supported lanes.
>> +	 */
>> +
>> +	if (speed >= PCIE_SPEED_8_0GT)
>> +		dw_pcie_program_presets(pp, PCIE_SPEED_8_0GT);
>> +
>> +	if (speed >= PCIE_SPEED_16_0GT)
>> +		dw_pcie_program_presets(pp, PCIE_SPEED_16_0GT);
> 
> Add other data rates also.
> 
> - Mani
>