[RFT PATCH 1/3] arm64: dts: rockchip: correct audio-codec interrupt flag in eaidk-610

[RFT PATCH 1/3] arm64: dts: rockchip: correct audio-codec interrupt flag in eaidk-610

[Krzysztof Kozlowski]

GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning: GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE.

Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
  ACTIVE_LOW  => IRQ_TYPE_LEVEL_LOW

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts b/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
index d1f343345f67..6464ef4d113d 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
@@ -773,7 +773,7 @@ brcmf: wifi@1 {
 		compatible = "brcm,bcm4329-fmac";
 		reg = <1>;
 		interrupt-parent = <&gpio0>;
-		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "host-wake";
 		pinctrl-names = "default";
 		pinctrl-0 = <&wifi_host_wake_l>;
-- 
2.34.1

[RFT PATCH 2/3] arm64: dts: rockchip: correct audio-codec interrupt flag in Rock Pi 4B

[Krzysztof Kozlowski]

GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning: GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE.

Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
  ACTIVE_LOW  => IRQ_TYPE_LEVEL_LOW

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b-plus.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b-plus.dts b/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b-plus.dts
index cec3b7b1b947..8a17c1eaae15 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b-plus.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b-plus.dts
@@ -31,7 +31,7 @@ brcmf: wifi@1 {
 		compatible = "brcm,bcm4329-fmac";
 		reg = <1>;
 		interrupt-parent = <&gpio0>;
-		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "host-wake";
 		pinctrl-names = "default";
 		pinctrl-0 = <&wifi_host_wake_l>;
-- 
2.34.1

[RFT PATCH 3/3] arm64: dts: rockchip: correct audio-codec interrupt flag in Box Demo

[Krzysztof Kozlowski]

GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning: GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE.

Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
  ACTIVE_LOW  => IRQ_TYPE_LEVEL_LOW

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 arch/arm64/boot/dts/rockchip/rk3566-box-demo.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3566-box-demo.dts b/arch/arm64/boot/dts/rockchip/rk3566-box-demo.dts
index 322f3e809f15..0c18406e4c59 100644
--- a/arch/arm64/boot/dts/rockchip/rk3566-box-demo.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3566-box-demo.dts
@@ -416,7 +416,7 @@ brcmf: wifi@1 {
 		compatible = "brcm,bcm4329-fmac";
 		reg = <1>;
 		interrupt-parent = <&gpio2>;
-		interrupts = <RK_PB2 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PB2 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "host-wake";
 		pinctrl-names = "default";
 		pinctrl-0 = <&wifi_host_wake_h>;
-- 
2.34.1

Re: [RFT PATCH 2/3] arm64: dts: rockchip: correct audio-codec interrupt flag in Rock Pi 4B

[Christopher Obbard]

Hi Krzysztof,

On Wed, 2023-07-05 at 08:48 +0200, Krzysztof Kozlowski wrote:
> GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
> These are simple defines so they could be used in DTS but they will not
> have the same meaning: GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE.
> 
> Correct the interrupt flags, assuming the author of the code wanted same
> logical behavior behind the name "ACTIVE_xxx", this is:
>   ACTIVE_LOW  => IRQ_TYPE_LEVEL_LOW
> 
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> ---

This works fine on my hardware. With that:

Tested-by: Christopher Obbard <chris.obbard@collabora.com>

>  arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b-plus.dts | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b-plus.dts b/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b-plus.dts
> index cec3b7b1b947..8a17c1eaae15 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b-plus.dts
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b-plus.dts
> @@ -31,7 +31,7 @@ brcmf: wifi@1 {
>                 compatible = "brcm,bcm4329-fmac";
>                 reg = <1>;
>                 interrupt-parent = <&gpio0>;
> -               interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
> +               interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
>                 interrupt-names = "host-wake";
>                 pinctrl-names = "default";
>                 pinctrl-0 = <&wifi_host_wake_l>;

Re: [RFT PATCH 1/3] arm64: dts: rockchip: correct audio-codec interrupt flag in eaidk-610

[Krzysztof Kozlowski]

On 05/07/2023 08:48, Krzysztof Kozlowski wrote:
> GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
> These are simple defines so they could be used in DTS but they will not
> have the same meaning: GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE.
> 
> Correct the interrupt flags, assuming the author of the code wanted same
> logical behavior behind the name "ACTIVE_xxx", this is:
>   ACTIVE_LOW  => IRQ_TYPE_LEVEL_LOW

This should be HIGH in both cases. I will send a v2.

> 
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> ---
>  arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts b/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
> index d1f343345f67..6464ef4d113d 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
> @@ -773,7 +773,7 @@ brcmf: wifi@1 {
>  		compatible = "brcm,bcm4329-fmac";
>  		reg = <1>;
>  		interrupt-parent = <&gpio0>;
> -		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
> +		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;

Best regards,
Krzysztof

Re: [RFT PATCH 1/3] arm64: dts: rockchip: correct audio-codec interrupt flag in eaidk-610

[Robin Murphy]

On 2023-07-06 14:54, Krzysztof Kozlowski wrote:
> On 05/07/2023 08:48, Krzysztof Kozlowski wrote:
>> GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
>> These are simple defines so they could be used in DTS but they will not
>> have the same meaning: GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE.
>>
>> Correct the interrupt flags, assuming the author of the code wanted same
>> logical behavior behind the name "ACTIVE_xxx", this is:
>>    ACTIVE_LOW  => IRQ_TYPE_LEVEL_LOW
> 
> This should be HIGH in both cases. I will send a v2.

Also the titles say "audio-codec" but they're all touching SDIO WiFi 
modules ;)

Cheers,
Robin.

>>
>> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
>> ---
>>   arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts | 2 +-
>>   1 file changed, 1 insertion(+), 1 deletion(-)
>>
>> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts b/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
>> index d1f343345f67..6464ef4d113d 100644
>> --- a/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
>> +++ b/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
>> @@ -773,7 +773,7 @@ brcmf: wifi@1 {
>>   		compatible = "brcm,bcm4329-fmac";
>>   		reg = <1>;
>>   		interrupt-parent = <&gpio0>;
>> -		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
>> +		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
> 
> Best regards,
> Krzysztof
> 
> 
> _______________________________________________
> Linux-rockchip mailing list
> Linux-rockchip@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-rockchip

Re: [RFT PATCH 1/3] arm64: dts: rockchip: correct audio-codec interrupt flag in eaidk-610

[Krzysztof Kozlowski]

On 06/07/2023 19:49, Robin Murphy wrote:
> On 2023-07-06 14:54, Krzysztof Kozlowski wrote:
>> On 05/07/2023 08:48, Krzysztof Kozlowski wrote:
>>> GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
>>> These are simple defines so they could be used in DTS but they will not
>>> have the same meaning: GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE.
>>>
>>> Correct the interrupt flags, assuming the author of the code wanted same
>>> logical behavior behind the name "ACTIVE_xxx", this is:
>>>    ACTIVE_LOW  => IRQ_TYPE_LEVEL_LOW
>>
>> This should be HIGH in both cases. I will send a v2.
> 
> Also the titles say "audio-codec" but they're all touching SDIO WiFi 
> modules ;)

Thanks. Too much of copy-pasta.

Best regards,
Krzysztof