From: Icenowy Zheng <icenowy-h8G6r0blFSE@public.gmane.org>
To: Maxime Ripard <maxime.ripard-LDxbnhwyfcJBDgjK7y7TUQ@public.gmane.org>
Cc: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw@public.gmane.org
Subject: Re: [PATCH v4] ARM: sun8i: h2+: add support for Banana Pi M2 Zero board
Date: Thu, 08 Feb 2018 17:15:35 +0800 [thread overview]
Message-ID: <9e77487f83b226ad7700715251178ce8@aosc.io> (raw)
In-Reply-To: <20180208090042.364is5ctofhuao4i@flea>
在 2018-02-08 17:00,Maxime Ripard 写道:
> On Tue, Feb 06, 2018 at 09:16:47PM +0800, Icenowy Zheng wrote:
>> Banana Pi M2 Zero board is a H2+-based board by Sinovoip, with a form
>> factor and GPIO holes similar to Raspberry Pi Zero.
>>
>> It features:
>> - Allwinner H2+ SoC
>> - Single-chip (16-bit) 512MiB DDR3 DRAM
>> - Ampak AP6212 Wi-Fi/Bluetooth module
>> - MicroSD slot
>> - Two MicroUSB Type-B ports (one can only be used to power the board
>> and
>> the other features OTG functionality)
>> - Two keys, a reset and a GPIO-connected key.
>> - HDMI Type-C (miniHDMI) connector connected to the HDMI part of H2+.
>> - CSI connector to connect the camera sensor provided by Sinovoip.
>>
>> Signed-off-by: Icenowy Zheng <icenowy-h8G6r0blFSE@public.gmane.org>
>> ---
>> Changes in v4:
>> - Use SPDX license identifier.
>>
>> Changes in v3:
>> - Add comments about Vbus problem in &usbphy node.
>>
>> Changes in v2:
>> - Use high active SD card detect on the production batch.
>>
>> arch/arm/boot/dts/Makefile | 1 +
>> .../boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 126
>> +++++++++++++++++++++
>> 2 files changed, 127 insertions(+)
>> create mode 100644
>> arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index ade7a38543dc..d5a17e6e8b0f 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -974,6 +974,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
>> sun8i-a83t-cubietruck-plus.dtb \
>> sun8i-a83t-tbs-a711.dtb \
>> sun8i-h2-plus-orangepi-r1.dtb \
>> + sun8i-h2-plus-bananapi-m2-zero.dtb \
>> sun8i-h2-plus-orangepi-zero.dtb \
>> sun8i-h3-bananapi-m2-plus.dtb \
>> sun8i-h3-beelink-x2.dtb \
>> diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>> b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>> new file mode 100644
>> index 000000000000..e2ee65a5bf92
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
>> @@ -0,0 +1,126 @@
>> +/*
>> + * Copyright (C) 2017 Icenowy Zheng <icenowy-h8G6r0blFSE@public.gmane.org>
>> + *
>> + * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
>> + * Copyright (C) 2016 Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
>> + *
>> + * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>
> Sorry to be a bit picky about this, but this should be your very first
> line, see arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts for
> example.
I think it's also OK here, see
arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts.
>
> Thanks!
> Maxime
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.
next prev parent reply other threads:[~2018-02-08 9:15 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-02-06 13:16 [PATCH v4] ARM: sun8i: h2+: add support for Banana Pi M2 Zero board Icenowy Zheng
2018-02-08 9:00 ` Maxime Ripard
2018-02-08 9:15 ` Icenowy Zheng [this message]
[not found] ` <9e77487f83b226ad7700715251178ce8-h8G6r0blFSE@public.gmane.org>
2018-02-08 9:28 ` Jernej Škrabec
2018-02-08 9:41 ` [linux-sunxi] " Chen-Yu Tsai
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=9e77487f83b226ad7700715251178ce8@aosc.io \
--to=icenowy-h8g6r0blfse@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
--cc=linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-sunxi-/JYPxA39Uh5TLH3MbocFFw@public.gmane.org \
--cc=maxime.ripard-LDxbnhwyfcJBDgjK7y7TUQ@public.gmane.org \
--cc=wens-jdAy2FN1RRM@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).