* [PATCH v8 1/7] arm64: dts: ti: k3-j7200-som-p0: Add TP6594 family PMICs
2023-11-28 5:52 [PATCH v8 0/7] Add TPS6594 PMIC support on several boards Neha Malcom Francis
@ 2023-11-28 5:52 ` Neha Malcom Francis
2023-11-28 5:52 ` [PATCH v8 2/7] arm64: dts: ti: k3-j721s2-som-p0: " Neha Malcom Francis
` (6 subsequent siblings)
7 siblings, 0 replies; 12+ messages in thread
From: Neha Malcom Francis @ 2023-11-28 5:52 UTC (permalink / raw)
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt, conor+dt,
a-nandan
Cc: linux-arm-kernel, devicetree, linux-kernel, eblanc, jneanne,
aseketeli, jpanis, u-kumar1, j-luthra, vaishnav.a, hnagalla,
devarsht, n-francis
From: Esteban Blanc <eblanc@baylibre.com>
This patch adds support for TPS6594 PMIC family on wakup I2C0 bus.
Theses devices provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
---
arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 157 ++++++++++++++++++++
1 file changed, 157 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
index 5a300d4c8ba0..f23b37293c8b 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
@@ -127,6 +127,14 @@ J721E_WKUP_IOPAD(0x9c, PIN_INPUT_PULLUP, 0) /* (H21) WKUP_I2C0_SDA */
};
};
+&wkup_pmx3 {
+ pmic_irq_pins_default: pmic-irq-default-pins {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0x01c, PIN_INPUT, 7) /* (E18) WKUP_GPIO0_84 */
+ >;
+ };
+};
+
&main_pmx0 {
main_i2c0_pins_default: main-i2c0-default-pins {
pinctrl-single,pins = <
@@ -264,6 +272,155 @@ eeprom@50 {
compatible = "atmel,24c256";
reg = <0x50>;
};
+
+ tps659414: pmic@48 {
+ compatible = "ti,tps6594-q1";
+ reg = <0x48>;
+ ti,primary-pmic;
+ system-power-controller;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_irq_pins_default>;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <84 IRQ_TYPE_EDGE_FALLING>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck1-supply = <&vsys_3v3>;
+ buck2-supply = <&vsys_3v3>;
+ buck3-supply = <&vsys_3v3>;
+ buck4-supply = <&vsys_3v3>;
+ buck5-supply = <&vsys_3v3>;
+ ldo1-supply = <&vsys_3v3>;
+ ldo2-supply = <&vsys_3v3>;
+ ldo3-supply = <&vsys_3v3>;
+ ldo4-supply = <&vsys_3v3>;
+
+ regulators {
+ bucka1: buck1 {
+ regulator-name = "vda_mcu_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka2: buck2 {
+ regulator-name = "vdd_mcuio_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka3: buck3 {
+ regulator-name = "vdd_mcu_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka4: buck4 {
+ regulator-name = "vdd_ddr_1v1";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka5: buck5 {
+ regulator-name = "vdd_phyio_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa1: ldo1 {
+ regulator-name = "vdd1_lpddr4_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa2: ldo2 {
+ regulator-name = "vda_dll_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa3: ldo3 {
+ regulator-name = "vdd_wk_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa4: ldo4 {
+ regulator-name = "vda_pll_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+
+ lp876441: pmic@4c {
+ compatible = "ti,lp8764-q1";
+ reg = <0x4c>;
+ system-power-controller;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <84 IRQ_TYPE_EDGE_FALLING>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck1-supply = <&vsys_3v3>;
+ buck2-supply = <&vsys_3v3>;
+ buck3-supply = <&vsys_3v3>;
+ buck4-supply = <&vsys_3v3>;
+
+ regulators: regulators {
+ buckb1: buck1 {
+ regulator-name = "vdd_cpu_avs";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <900000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buckb2: buck2 {
+ regulator-name = "vdd_ram_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buckb3: buck3 {
+ regulator-name = "vdd_core_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buckb4: buck4 {
+ regulator-name = "vdd_io_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
};
&ospi0 {
--
2.34.1
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v8 2/7] arm64: dts: ti: k3-j721s2-som-p0: Add TP6594 family PMICs
2023-11-28 5:52 [PATCH v8 0/7] Add TPS6594 PMIC support on several boards Neha Malcom Francis
2023-11-28 5:52 ` [PATCH v8 1/7] arm64: dts: ti: k3-j7200-som-p0: Add TP6594 family PMICs Neha Malcom Francis
@ 2023-11-28 5:52 ` Neha Malcom Francis
2023-11-28 5:52 ` [PATCH v8 3/7] arm64: dts: ti: k3-j721e-som-p0: " Neha Malcom Francis
` (5 subsequent siblings)
7 siblings, 0 replies; 12+ messages in thread
From: Neha Malcom Francis @ 2023-11-28 5:52 UTC (permalink / raw)
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt, conor+dt,
a-nandan
Cc: linux-arm-kernel, devicetree, linux-kernel, eblanc, jneanne,
aseketeli, jpanis, u-kumar1, j-luthra, vaishnav.a, hnagalla,
devarsht, n-francis
From: Esteban Blanc <eblanc@baylibre.com>
This patch adds support for TPS6594 PMIC family on wakup I2C0 bus.
Theses devices provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
---
arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 199 +++++++++++++++++++
1 file changed, 199 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
index dcad372620b1..f02fab4f6fda 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
@@ -172,6 +172,15 @@ J721S2_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (E20) MCU_OSPI0_LBCLKO */
};
};
+&wkup_pmx1 {
+ pmic_irq_pins_default: pmic-irq-default-pins {
+ pinctrl-single,pins = <
+ /* (C21) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */
+ J721S2_WKUP_IOPAD(0x028, PIN_INPUT, 7)
+ >;
+ };
+};
+
&wkup_pmx2 {
wkup_i2c0_pins_default: wkup-i2c0-default-pins {
pinctrl-single,pins = <
@@ -208,6 +217,196 @@ eeprom@50 {
compatible = "atmel,24c256";
reg = <0x50>;
};
+
+ tps659411: pmic@48 {
+ compatible = "ti,tps6594-q1";
+ reg = <0x48>;
+ ti,primary-pmic;
+ system-power-controller;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_irq_pins_default>;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck1234-supply = <&vsys_3v3>;
+ buck5-supply = <&vsys_3v3>;
+ ldo1-supply = <&vsys_3v3>;
+ ldo2-supply = <&vsys_3v3>;
+ ldo3-supply = <&vsys_3v3>;
+ ldo4-supply = <&vsys_3v3>;
+
+ regulators {
+ bucka1234: buck1234 {
+ regulator-name = "vdd_cpu_avs";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka5: buck5 {
+ regulator-name = "vdd_mcu_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa1: ldo1 {
+ regulator-name = "vdd_mcuwk_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa2: ldo2 {
+ regulator-name = "vdd_mcu_gpioret_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa3: ldo3 {
+ regulator-name = "vdd_mcuio_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa4: ldo4 {
+ regulator-name = "vda_mcu_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+
+ tps659414: pmic@4c {
+ compatible = "ti,tps6594-q1";
+ reg = <0x4c>;
+ system-power-controller;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck1-supply = <&vsys_3v3>;
+ buck2-supply = <&vsys_3v3>;
+ buck3-supply = <&vsys_3v3>;
+ buck4-supply = <&vsys_3v3>;
+ buck5-supply = <&vsys_3v3>;
+ ldo1-supply = <&vsys_3v3>;
+ ldo2-supply = <&vsys_3v3>;
+ ldo3-supply = <&vsys_3v3>;
+ ldo4-supply = <&vsys_3v3>;
+
+ regulators {
+ buckb1: buck1 {
+ regulator-name = "vdd_io_1v8_reg";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buckb2: buck2 {
+ regulator-name = "vdd_fpd_1v1";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buckb3: buck3 {
+ regulator-name = "vdd_phy_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buckb4: buck4 {
+ regulator-name = "vdd_ddr_1v1";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buckb5: buck5 {
+ regulator-name = "vdd_ram_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob1: ldo1 {
+ regulator-name = "vdd_wk_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob2: ldo2 {
+ regulator-name = "vdd_gpioret_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob3: ldo3 {
+ regulator-name = "vda_dll_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob4: ldo4 {
+ regulator-name = "vda_pll_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+
+ lp876411: pmic@58 {
+ compatible = "ti,lp8764-q1";
+ reg = <0x58>;
+ system-power-controller;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck1234-supply = <&vsys_3v3>;
+
+ regulators {
+ buckc1234: buck1234 {
+ regulator-name = "vdd_core_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
};
&main_i2c0 {
--
2.34.1
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v8 3/7] arm64: dts: ti: k3-j721e-som-p0: Add TP6594 family PMICs
2023-11-28 5:52 [PATCH v8 0/7] Add TPS6594 PMIC support on several boards Neha Malcom Francis
2023-11-28 5:52 ` [PATCH v8 1/7] arm64: dts: ti: k3-j7200-som-p0: Add TP6594 family PMICs Neha Malcom Francis
2023-11-28 5:52 ` [PATCH v8 2/7] arm64: dts: ti: k3-j721s2-som-p0: " Neha Malcom Francis
@ 2023-11-28 5:52 ` Neha Malcom Francis
2023-11-28 5:52 ` [PATCH v8 4/7] arm64: dts: ti: k3-j784s4-evm: Add support for TPS6594 PMIC Neha Malcom Francis
` (4 subsequent siblings)
7 siblings, 0 replies; 12+ messages in thread
From: Neha Malcom Francis @ 2023-11-28 5:52 UTC (permalink / raw)
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt, conor+dt,
a-nandan
Cc: linux-arm-kernel, devicetree, linux-kernel, eblanc, jneanne,
aseketeli, jpanis, u-kumar1, j-luthra, vaishnav.a, hnagalla,
devarsht, n-francis
From: Jerome Neanne <jneanne@baylibre.com>
This patch adds support for TPS6594 PMIC family on wakup I2C0 bus.
Theses devices provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.
Signed-off-by: Jerome Neanne <jneanne@baylibre.com>
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
---
arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi | 163 ++++++++++++++++++++
1 file changed, 163 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
index 7f0686c2ce37..64cb2a34b16f 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
@@ -152,6 +152,12 @@ J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
>;
};
+ pmic_irq_pins_default: pmic-irq-default-pins {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0x0d4, PIN_INPUT, 7) /* (G26) WKUP_GPIO0_9 */
+ >;
+ };
+
mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
pinctrl-single,pins = <
J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_OSPI0_CLK */
@@ -199,6 +205,163 @@ eeprom@50 {
compatible = "atmel,24c256";
reg = <0x50>;
};
+
+ tps659413: pmic@48 {
+ compatible = "ti,tps6594-q1";
+ reg = <0x48>;
+ system-power-controller;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_irq_pins_default>;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+ ti,primary-pmic;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck12-supply = <&vsys_3v3>;
+ buck3-supply = <&vsys_3v3>;
+ buck4-supply = <&vsys_3v3>;
+ buck5-supply = <&vsys_3v3>;
+ ldo1-supply = <&vsys_3v3>;
+ ldo2-supply = <&vsys_3v3>;
+ ldo3-supply = <&vsys_3v3>;
+ ldo4-supply = <&vsys_3v3>;
+
+ regulators {
+ bucka12: buck12 {
+ regulator-name = "vdd_cpu_avs";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka3: buck3 {
+ regulator-name = "vdd_mcu_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka4: buck4 {
+ regulator-name = "vdd_ddr_1v1";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka5: buck5 {
+ regulator-name = "vdd_phyio_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa1: ldo1 {
+ regulator-name = "vdd1_lpddr4_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa2: ldo2 {
+ regulator-name = "vdd_mcuio_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa3: ldo3 {
+ regulator-name = "vdda_dll_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa4: ldo4 {
+ regulator-name = "vda_mcu_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+
+ tps659411: pmic@4c {
+ compatible = "ti,tps6594-q1";
+ reg = <0x4c>;
+ system-power-controller;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck1234-supply = <&vsys_3v3>;
+ buck5-supply = <&vsys_3v3>;
+ ldo1-supply = <&vsys_3v3>;
+ ldo2-supply = <&vsys_3v3>;
+ ldo3-supply = <&vsys_3v3>;
+ ldo4-supply = <&vsys_3v3>;
+
+ regulators {
+ buckb1234: buck1234 {
+ regulator-name = "vdd_core_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buckb5: buck5 {
+ regulator-name = "vdd_ram_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob1: ldo1 {
+ regulator-name = "vdd_sd_dv";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob2: ldo2 {
+ regulator-name = "vdd_usb_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob3: ldo3 {
+ regulator-name = "vdd_io_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob4: ldo4 {
+ regulator-name = "vda_pll_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
};
&ospi0 {
--
2.34.1
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v8 4/7] arm64: dts: ti: k3-j784s4-evm: Add support for TPS6594 PMIC
2023-11-28 5:52 [PATCH v8 0/7] Add TPS6594 PMIC support on several boards Neha Malcom Francis
` (2 preceding siblings ...)
2023-11-28 5:52 ` [PATCH v8 3/7] arm64: dts: ti: k3-j721e-som-p0: " Neha Malcom Francis
@ 2023-11-28 5:52 ` Neha Malcom Francis
2023-11-28 5:52 ` [PATCH v8 5/7] arm64: dts: ti: k3-am69-sk: " Neha Malcom Francis
` (3 subsequent siblings)
7 siblings, 0 replies; 12+ messages in thread
From: Neha Malcom Francis @ 2023-11-28 5:52 UTC (permalink / raw)
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt, conor+dt,
a-nandan
Cc: linux-arm-kernel, devicetree, linux-kernel, eblanc, jneanne,
aseketeli, jpanis, u-kumar1, j-luthra, vaishnav.a, hnagalla,
devarsht, n-francis
From: Jerome Neanne <jneanne@baylibre.com>
This patch adds support for TPS6593 PMIC on wkup I2C0 bus.
This device provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.
Signed-off-by: Jerome Neanne <jneanne@baylibre.com>
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
---
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 104 +++++++++++++++++++++++
1 file changed, 104 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index f1f4c8634ab6..dbc75af48774 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -273,6 +273,10 @@ dp0_connector_in: endpoint {
};
};
+&wkup_gpio0 {
+ status = "okay";
+};
+
&main_pmx0 {
bootph-all;
main_uart8_pins_default: main-uart8-default-pins {
@@ -407,6 +411,17 @@ J784S4_WKUP_IOPAD(0x108, PIN_INPUT, 0) /* (Y36) MCU_ADC1_AIN7 */
};
};
+&wkup_pmx1 {
+ status = "okay";
+
+ pmic_irq_pins_default: pmic-irq-default-pins {
+ pinctrl-single,pins = <
+ /* (G33) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */
+ J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 7)
+ >;
+ };
+};
+
&wkup_pmx0 {
bootph-all;
mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
@@ -471,6 +486,95 @@ eeprom@50 {
compatible = "atmel,24c256";
reg = <0x50>;
};
+
+ tps659413: pmic@48 {
+ compatible = "ti,tps6594-q1";
+ reg = <0x48>;
+ system-power-controller;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_irq_pins_default>;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+ ti,primary-pmic;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck12-supply = <&vsys_3v3>;
+ buck3-supply = <&vsys_3v3>;
+ buck4-supply = <&vsys_3v3>;
+ buck5-supply = <&vsys_3v3>;
+ ldo1-supply = <&vsys_3v3>;
+ ldo2-supply = <&vsys_3v3>;
+ ldo3-supply = <&vsys_3v3>;
+ ldo4-supply = <&vsys_3v3>;
+
+ regulators {
+ bucka12: buck12 {
+ regulator-name = "vdd_ddr_1v1";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka3: buck3 {
+ regulator-name = "vdd_ram_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka4: buck4 {
+ regulator-name = "vdd_io_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka5: buck5 {
+ regulator-name = "vdd_mcu_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa1: ldo1 {
+ regulator-name = "vdd_mcuio_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa2: ldo2 {
+ regulator-name = "vdd_mcuio_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa3: ldo3 {
+ regulator-name = "vds_dll_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa4: ldo4 {
+ regulator-name = "vda_mcu_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
};
&mcu_uart0 {
--
2.34.1
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v8 5/7] arm64: dts: ti: k3-am69-sk: Add support for TPS6594 PMIC
2023-11-28 5:52 [PATCH v8 0/7] Add TPS6594 PMIC support on several boards Neha Malcom Francis
` (3 preceding siblings ...)
2023-11-28 5:52 ` [PATCH v8 4/7] arm64: dts: ti: k3-j784s4-evm: Add support for TPS6594 PMIC Neha Malcom Francis
@ 2023-11-28 5:52 ` Neha Malcom Francis
2023-12-01 10:26 ` Manorit Chawdhry
2023-11-28 5:52 ` [PATCH v8 6/7] arm64: dts: ti: k3-j721e-sk: Add TPS6594 family PMICs Neha Malcom Francis
` (2 subsequent siblings)
7 siblings, 1 reply; 12+ messages in thread
From: Neha Malcom Francis @ 2023-11-28 5:52 UTC (permalink / raw)
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt, conor+dt,
a-nandan
Cc: linux-arm-kernel, devicetree, linux-kernel, eblanc, jneanne,
aseketeli, jpanis, u-kumar1, j-luthra, vaishnav.a, hnagalla,
devarsht, n-francis
This patch adds support for TPS6594 PMIC on wkup I2C0 bus. This device
provides regulators (bucks and LDOs), but also GPIOs, a RTC, a watchdog,
an ESM (Error Signal Monitor) which monitors the SoC error output
signal, and a PFSM (Pre-configurable Finite State Machine) which manages
the operational modes of the PMIC.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
---
arch/arm64/boot/dts/ti/k3-am69-sk.dts | 100 ++++++++++++++++++++++++++
1 file changed, 100 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am69-sk.dts b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
index 9868c7049bfb..dec27acb4e96 100644
--- a/arch/arm64/boot/dts/ti/k3-am69-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
@@ -431,6 +431,17 @@ J784S4_IOPAD(0x000, PIN_INPUT, 7) /* (AN35) EXTINTN.GPIO0_0 */
};
};
+&wkup_pmx1 {
+ status = "okay";
+
+ pmic_irq_pins_default: pmic-irq-default-pins {
+ pinctrl-single,pins = <
+ /* (AA37) MCU_ADC1_AIN4.WKUP_GPIO0_83 */
+ J784S4_WKUP_IOPAD(0x12c, PIN_INPUT, 7)
+ >;
+ };
+};
+
&wkup_pmx2 {
bootph-all;
wkup_uart0_pins_default: wkup-uart0-default-pins {
@@ -631,6 +642,95 @@ eeprom@51 {
compatible = "atmel,24c512";
reg = <0x51>;
};
+
+ tps659413: pmic@48 {
+ compatible = "ti,tps6594-q1";
+ reg = <0x48>;
+ system-power-controller;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_irq_pins_default>;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+ ti,primary-pmic;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck12-supply = <&vsys_3v3>;
+ buck3-supply = <&vsys_3v3>;
+ buck4-supply = <&vsys_3v3>;
+ buck5-supply = <&vsys_3v3>;
+ ldo1-supply = <&vsys_3v3>;
+ ldo2-supply = <&vsys_3v3>;
+ ldo3-supply = <&vsys_3v3>;
+ ldo4-supply = <&vsys_3v3>;
+
+ regulators {
+ bucka12: buck12 {
+ regulator-name = "vdd_ddr_1v1";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka3: buck3 {
+ regulator-name = "vdd_ram_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka4: buck4 {
+ regulator-name = "vdd_io_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka5: buck5 {
+ regulator-name = "vdd_mcu_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa1: ldo1 {
+ regulator-name = "vdd_mcuio_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa2: ldo2 {
+ regulator-name = "vdd_mcuio_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa3: ldo3 {
+ regulator-name = "vds_dll_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa4: ldo4 {
+ regulator-name = "vda_mcu_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
};
&wkup_gpio0 {
--
2.34.1
^ permalink raw reply related [flat|nested] 12+ messages in thread* Re: [PATCH v8 5/7] arm64: dts: ti: k3-am69-sk: Add support for TPS6594 PMIC
2023-11-28 5:52 ` [PATCH v8 5/7] arm64: dts: ti: k3-am69-sk: " Neha Malcom Francis
@ 2023-12-01 10:26 ` Manorit Chawdhry
2023-12-01 10:30 ` Neha Malcom Francis
0 siblings, 1 reply; 12+ messages in thread
From: Manorit Chawdhry @ 2023-12-01 10:26 UTC (permalink / raw)
To: Neha Malcom Francis
Cc: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt, conor+dt,
a-nandan, linux-arm-kernel, devicetree, linux-kernel, eblanc,
jneanne, aseketeli, jpanis, u-kumar1, j-luthra, vaishnav.a,
hnagalla, devarsht
Hi Neha,
On 11:22-20231128, Neha Malcom Francis wrote:
> This patch adds support for TPS6594 PMIC on wkup I2C0 bus. This device
> provides regulators (bucks and LDOs), but also GPIOs, a RTC, a watchdog,
> an ESM (Error Signal Monitor) which monitors the SoC error output
> signal, and a PFSM (Pre-configurable Finite State Machine) which manages
> the operational modes of the PMIC.
>
> Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
> ---
> arch/arm64/boot/dts/ti/k3-am69-sk.dts | 100 ++++++++++++++++++++++++++
> 1 file changed, 100 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am69-sk.dts b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
> index 9868c7049bfb..dec27acb4e96 100644
> --- a/arch/arm64/boot/dts/ti/k3-am69-sk.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
> @@ -431,6 +431,17 @@ J784S4_IOPAD(0x000, PIN_INPUT, 7) /* (AN35) EXTINTN.GPIO0_0 */
> };
> };
>
> +&wkup_pmx1 {
> + status = "okay";
> +
> + pmic_irq_pins_default: pmic-irq-default-pins {
> + pinctrl-single,pins = <
> + /* (AA37) MCU_ADC1_AIN4.WKUP_GPIO0_83 */
> + J784S4_WKUP_IOPAD(0x12c, PIN_INPUT, 7)
> + >;
> + };
> +};
> +
> &wkup_pmx2 {
> bootph-all;
> wkup_uart0_pins_default: wkup-uart0-default-pins {
> @@ -631,6 +642,95 @@ eeprom@51 {
> compatible = "atmel,24c512";
> reg = <0x51>;
> };
> +
> + tps659413: pmic@48 {
> + compatible = "ti,tps6594-q1";
> + reg = <0x48>;
> + system-power-controller;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_irq_pins_default>;
> + interrupt-parent = <&wkup_gpio0>;
> + interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
> + ti,primary-pmic;
> +
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + buck12-supply = <&vsys_3v3>;
> + buck3-supply = <&vsys_3v3>;
> + buck4-supply = <&vsys_3v3>;
> + buck5-supply = <&vsys_3v3>;
> + ldo1-supply = <&vsys_3v3>;
> + ldo2-supply = <&vsys_3v3>;
> + ldo3-supply = <&vsys_3v3>;
> + ldo4-supply = <&vsys_3v3>;
> +
> + regulators {
> + bucka12: buck12 {
> + regulator-name = "vdd_ddr_1v1";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + bucka3: buck3 {
> + regulator-name = "vdd_ram_0v85";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <850000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + bucka4: buck4 {
> + regulator-name = "vdd_io_1v8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + bucka5: buck5 {
> + regulator-name = "vdd_mcu_0v85";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <850000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldoa1: ldo1 {
> + regulator-name = "vdd_mcuio_1v8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldoa2: ldo2 {
> + regulator-name = "vdd_mcuio_3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldoa3: ldo3 {
> + regulator-name = "vds_dll_0v8";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldoa4: ldo4 {
> + regulator-name = "vda_mcu_1v8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> + };
> + };
> };
>
With the full series applied:
https://gist.github.com/manorit2001/7e794a7cbf58af4d7fbbee03eac88e86
[ For AM69-SK ]
Tested-by: Manorit Chawdhry <m-chawdhry@ti.com>
Regards,
Manorit
> &wkup_gpio0 {
> --
> 2.34.1
>
^ permalink raw reply [flat|nested] 12+ messages in thread* Re: [PATCH v8 5/7] arm64: dts: ti: k3-am69-sk: Add support for TPS6594 PMIC
2023-12-01 10:26 ` Manorit Chawdhry
@ 2023-12-01 10:30 ` Neha Malcom Francis
0 siblings, 0 replies; 12+ messages in thread
From: Neha Malcom Francis @ 2023-12-01 10:30 UTC (permalink / raw)
To: Manorit Chawdhry
Cc: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt, conor+dt,
a-nandan, linux-arm-kernel, devicetree, linux-kernel, eblanc,
jneanne, aseketeli, jpanis, u-kumar1, j-luthra, vaishnav.a,
hnagalla, devarsht
Hi Manorit
On 01-Dec-23 3:56 PM, Manorit Chawdhry wrote:
> Hi Neha,
>
> On 11:22-20231128, Neha Malcom Francis wrote:
>> This patch adds support for TPS6594 PMIC on wkup I2C0 bus. This device
>> provides regulators (bucks and LDOs), but also GPIOs, a RTC, a watchdog,
>> an ESM (Error Signal Monitor) which monitors the SoC error output
>> signal, and a PFSM (Pre-configurable Finite State Machine) which manages
>> the operational modes of the PMIC.
>>
>> Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
>> ---
>> arch/arm64/boot/dts/ti/k3-am69-sk.dts | 100 ++++++++++++++++++++++++++
>> 1 file changed, 100 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-am69-sk.dts b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
>> index 9868c7049bfb..dec27acb4e96 100644
>> --- a/arch/arm64/boot/dts/ti/k3-am69-sk.dts
>> +++ b/arch/arm64/boot/dts/ti/k3-am69-sk.dts
>> @@ -431,6 +431,17 @@ J784S4_IOPAD(0x000, PIN_INPUT, 7) /* (AN35) EXTINTN.GPIO0_0 */
>> };
>> };
>>
>> +&wkup_pmx1 {
>> + status = "okay";
>> +
>> + pmic_irq_pins_default: pmic-irq-default-pins {
>> + pinctrl-single,pins = <
>> + /* (AA37) MCU_ADC1_AIN4.WKUP_GPIO0_83 */
>> + J784S4_WKUP_IOPAD(0x12c, PIN_INPUT, 7)
>> + >;
>> + };
>> +};
>> +
>> &wkup_pmx2 {
>> bootph-all;
>> wkup_uart0_pins_default: wkup-uart0-default-pins {
>> @@ -631,6 +642,95 @@ eeprom@51 {
>> compatible = "atmel,24c512";
>> reg = <0x51>;
>> };
>> +
>> + tps659413: pmic@48 {
>> + compatible = "ti,tps6594-q1";
>> + reg = <0x48>;
>> + system-power-controller;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pmic_irq_pins_default>;
>> + interrupt-parent = <&wkup_gpio0>;
>> + interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
>> + ti,primary-pmic;
>> +
>> + gpio-controller;
>> + #gpio-cells = <2>;
>> +
>> + buck12-supply = <&vsys_3v3>;
>> + buck3-supply = <&vsys_3v3>;
>> + buck4-supply = <&vsys_3v3>;
>> + buck5-supply = <&vsys_3v3>;
>> + ldo1-supply = <&vsys_3v3>;
>> + ldo2-supply = <&vsys_3v3>;
>> + ldo3-supply = <&vsys_3v3>;
>> + ldo4-supply = <&vsys_3v3>;
>> +
>> + regulators {
>> + bucka12: buck12 {
>> + regulator-name = "vdd_ddr_1v1";
>> + regulator-min-microvolt = <1100000>;
>> + regulator-max-microvolt = <1100000>;
>> + regulator-boot-on;
>> + regulator-always-on;
>> + };
>> +
>> + bucka3: buck3 {
>> + regulator-name = "vdd_ram_0v85";
>> + regulator-min-microvolt = <850000>;
>> + regulator-max-microvolt = <850000>;
>> + regulator-boot-on;
>> + regulator-always-on;
>> + };
>> +
>> + bucka4: buck4 {
>> + regulator-name = "vdd_io_1v8";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-boot-on;
>> + regulator-always-on;
>> + };
>> +
>> + bucka5: buck5 {
>> + regulator-name = "vdd_mcu_0v85";
>> + regulator-min-microvolt = <850000>;
>> + regulator-max-microvolt = <850000>;
>> + regulator-boot-on;
>> + regulator-always-on;
>> + };
>> +
>> + ldoa1: ldo1 {
>> + regulator-name = "vdd_mcuio_1v8";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-boot-on;
>> + regulator-always-on;
>> + };
>> +
>> + ldoa2: ldo2 {
>> + regulator-name = "vdd_mcuio_3v3";
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-boot-on;
>> + regulator-always-on;
>> + };
>> +
>> + ldoa3: ldo3 {
>> + regulator-name = "vds_dll_0v8";
>> + regulator-min-microvolt = <800000>;
>> + regulator-max-microvolt = <800000>;
>> + regulator-boot-on;
>> + regulator-always-on;
>> + };
>> +
>> + ldoa4: ldo4 {
>> + regulator-name = "vda_mcu_1v8";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-boot-on;
>> + regulator-always-on;
>> + };
>> + };
>> + };
>> };
>>
>
> With the full series applied:
> https://gist.github.com/manorit2001/7e794a7cbf58af4d7fbbee03eac88e86
>
> [ For AM69-SK ]
> Tested-by: Manorit Chawdhry <m-chawdhry@ti.com>
>
> Regards,
> Manorit
>
>> &wkup_gpio0 {
>> --
>> 2.34.1
>>
Thanks for testing!
--
Thanking You
Neha Malcom Francis
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v8 6/7] arm64: dts: ti: k3-j721e-sk: Add TPS6594 family PMICs
2023-11-28 5:52 [PATCH v8 0/7] Add TPS6594 PMIC support on several boards Neha Malcom Francis
` (4 preceding siblings ...)
2023-11-28 5:52 ` [PATCH v8 5/7] arm64: dts: ti: k3-am69-sk: " Neha Malcom Francis
@ 2023-11-28 5:52 ` Neha Malcom Francis
2023-11-28 5:52 ` [PATCH v8 7/7] DONOTMERGE: arm64: defconfig: Enable TPS6594 PMIC for J7 devices Neha Malcom Francis
2023-12-04 4:09 ` [PATCH v8 0/7] Add TPS6594 PMIC support on several boards Kumar, Udit
7 siblings, 0 replies; 12+ messages in thread
From: Neha Malcom Francis @ 2023-11-28 5:52 UTC (permalink / raw)
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt, conor+dt,
a-nandan
Cc: linux-arm-kernel, devicetree, linux-kernel, eblanc, jneanne,
aseketeli, jpanis, u-kumar1, j-luthra, vaishnav.a, hnagalla,
devarsht, n-francis
This patch adds support for TPS6594 PMIC family on wakeup I2C0 bus.
These devices provide regulators (bucks and LDOs), but also GPIOs, a
RTC, a watchdog, an ESM (Error Signal Monitor) which monitors the SoC
error output signal, and a PFSM (Pre-configurable Finite State Machine)
which manages the operational modes of the PMIC.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
---
arch/arm64/boot/dts/ti/k3-j721e-sk.dts | 154 +++++++++++++++++++++++++
1 file changed, 154 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-sk.dts b/arch/arm64/boot/dts/ti/k3-j721e-sk.dts
index 42fe8eee9ec8..3e801b4cdb1e 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721e-sk.dts
@@ -459,6 +459,12 @@ J721E_IOPAD(0x234, PIN_INPUT, 7) /* (U3) EXT_REFCLK1.GPIO1_12 */
};
&wkup_pmx0 {
+ pmic_irq_pins_default: pmic-irq-default-pins {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0x0cc, PIN_INPUT, 7) /* (G28) WKUP_GPIO0_7 */
+ >;
+ };
+
mcu_cpsw_pins_default: mcu-cpsw-default-pins {
pinctrl-single,pins = <
J721E_WKUP_IOPAD(0x84, PIN_INPUT, 0) /* (B24) MCU_RGMII1_RD0 */
@@ -560,6 +566,154 @@ eeprom@51 {
compatible = "atmel,24c512";
reg = <0x51>;
};
+
+ tps659413: pmic@48 {
+ compatible = "ti,tps6594-q1";
+ reg = <0x48>;
+ system-power-controller;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_irq_pins_default>;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+ ti,primary-pmic;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck123-supply = <&vsys_3v3>;
+ buck4-supply = <&vsys_3v3>;
+ buck5-supply = <&vsys_3v3>;
+ ldo1-supply = <&vsys_3v3>;
+ ldo2-supply = <&vsys_3v3>;
+ ldo3-supply = <&vsys_3v3>;
+ ldo4-supply = <&vsys_3v3>;
+
+ regulators {
+ bucka123: buck123 {
+ regulator-name = "vdd_cpu_avs";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka4: buck4 {
+ regulator-name = "vdd_mcu_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka5: buck5 {
+ regulator-name = "vdd_phyio_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa1: ldo1 {
+ regulator-name = "vdd1_lpddr4_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa2: ldo2 {
+ regulator-name = "vdd_mcuio_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa3: ldo3 {
+ regulator-name = "vdda_dll_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa4: ldo4 {
+ regulator-name = "vda_mcu_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+
+ tps659411: pmic@4c {
+ compatible = "ti,tps6594-q1";
+ reg = <0x4c>;
+ system-power-controller;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck1234-supply = <&vsys_3v3>;
+ buck5-supply = <&vsys_3v3>;
+ ldo1-supply = <&vsys_3v3>;
+ ldo2-supply = <&vsys_3v3>;
+ ldo3-supply = <&vsys_3v3>;
+ ldo4-supply = <&vsys_3v3>;
+
+ regulators {
+ buckb1234: buck1234 {
+ regulator-name = "vdd_core_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buckb5: buck5 {
+ regulator-name = "vdd_ram_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob1: ldo1 {
+ regulator-name = "vdd_sd_dv";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob2: ldo2 {
+ regulator-name = "vdd_usb_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob3: ldo3 {
+ regulator-name = "vdd_io_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob4: ldo4 {
+ regulator-name = "vda_pll_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
};
&mcu_uart0 {
--
2.34.1
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v8 7/7] DONOTMERGE: arm64: defconfig: Enable TPS6594 PMIC for J7 devices
2023-11-28 5:52 [PATCH v8 0/7] Add TPS6594 PMIC support on several boards Neha Malcom Francis
` (5 preceding siblings ...)
2023-11-28 5:52 ` [PATCH v8 6/7] arm64: dts: ti: k3-j721e-sk: Add TPS6594 family PMICs Neha Malcom Francis
@ 2023-11-28 5:52 ` Neha Malcom Francis
2023-12-04 4:09 ` [PATCH v8 0/7] Add TPS6594 PMIC support on several boards Kumar, Udit
7 siblings, 0 replies; 12+ messages in thread
From: Neha Malcom Francis @ 2023-11-28 5:52 UTC (permalink / raw)
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt, conor+dt,
a-nandan
Cc: linux-arm-kernel, devicetree, linux-kernel, eblanc, jneanne,
aseketeli, jpanis, u-kumar1, j-luthra, vaishnav.a, hnagalla,
devarsht, n-francis
J7 (J721E-EVM, J721E-SK, J721S2, AM68-SK, J784S4, AM69-SK) devices use
TPS6594x PMIC (interfaced over I2C) to power the SoC and various other
peripherals on the board [1].
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
---
arch/arm64/configs/defconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index b60aa1f89343..682251135267 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -727,7 +727,7 @@ CONFIG_MFD_SEC_CORE=y
CONFIG_MFD_SL28CPLD=y
CONFIG_RZ_MTU3=y
CONFIG_MFD_TPS65219=y
-CONFIG_MFD_TPS6594_I2C=m
+CONFIG_MFD_TPS6594_I2C=y
CONFIG_MFD_TI_AM335X_TSCADC=m
CONFIG_MFD_ROHM_BD718XX=y
CONFIG_MFD_WCD934X=m
--
2.34.1
^ permalink raw reply related [flat|nested] 12+ messages in thread* Re: [PATCH v8 0/7] Add TPS6594 PMIC support on several boards
2023-11-28 5:52 [PATCH v8 0/7] Add TPS6594 PMIC support on several boards Neha Malcom Francis
` (6 preceding siblings ...)
2023-11-28 5:52 ` [PATCH v8 7/7] DONOTMERGE: arm64: defconfig: Enable TPS6594 PMIC for J7 devices Neha Malcom Francis
@ 2023-12-04 4:09 ` Kumar, Udit
2023-12-04 4:12 ` Neha Malcom Francis
7 siblings, 1 reply; 12+ messages in thread
From: Kumar, Udit @ 2023-12-04 4:09 UTC (permalink / raw)
To: Neha Malcom Francis, nm, vigneshr, kristo, robh+dt,
krzysztof.kozlowski+dt, conor+dt, a-nandan
Cc: linux-arm-kernel, devicetree, linux-kernel, eblanc, jneanne,
aseketeli, jpanis, j-luthra, vaishnav.a, hnagalla, devarsht
On 11/28/2023 11:22 AM, Neha Malcom Francis wrote:
> TPS6594 is a Power Management IC which provides regulators and others
> features like GPIOs, RTC, watchdog, ESMs (Error Signal Monitor), and
> PFSM (Pre-configurable Finite State Machine). The SoC and the PMIC can
> communicate through the I2C or SPI interfaces.
> TPS6594 is the super-set device while TPS6593 and LP8764 are derivatives.
Please consider adding bootph property in avs regulator node.
Thanks
Udit
> This series adds device tree nodes for TI TPS6594 PMICs found in the
> following boards:
> - J721EXSOMXEVM:
> Link: https://www.ti.com/tool/J721EXSOMXEVM
> - J721S2XSOMXEVM:
> Link: https://www.ti.com/tool/J721S2XSOMXEVM
> - J7200XSOMXEVM:
> Link: https://www.ti.com/tool/J7200XSOMXEVM
> - J784S4XEVM
> Link: https://www.ti.com/tool/J784S4XEVM
> - SK-AM69
> Link: https://www.ti.com/tool/SK-AM69
> - SK-TDA4VM (J721E-SK)
> Link: https://www.ti.com/tool/SK-TDA4VM
>
> Boot Logs with required config (DONOTMERGE patch) enabled:
> https://gist.github.com/nehamalcom/f47fcd6183360ed8a146c9ba456202c3
> Boot Logs without config enabled:
> https://gist.github.com/nehamalcom/58217b100e614ae55726f314e02b5001
>
> ---
> Changes from v7:
> https://lore.kernel.org/all/20231122104513.2335757-1-n-francis@ti.com/
> - (New Patches) Add support for SK boards that have TPS6594xx PMIC
> present (J721E-SK and AM69-SK)
> - Add DONOTMERGE defconfig patch to show test logs
>
> Changes from v6:
> https://lore.kernel.org/all/20230810-tps6594-v6-0-2b2e2399e2ef@ti.com/
> - Modify patch series to include only patches not merged (J7)
> - Add boot logs for all affected boards
>
> Changes from v5:
> https://lore.kernel.org/all/20230809-tps6594-v5-0-485fd3d63670@ti.com
> - Range-diff: http://0x0.st/H_fD.diff
> - Reword the patch fixing interrupt ranges for mcu domain gpio intr, and
> add Fixes: tag
> - Also fix interrupt ranges for main domain gpio intr in the same patch
> - Change pinctrl node names to end in -pins to fix dtbs_check warnings
> - (New Patch) Enable TPS6594 in defconfig
>
> Changes from v4:
> https://lore.kernel.org/all/20230727130908.10656-1-eblanc@baylibre.com/
> - Range-diff: https://0x0.st/H_L7.diff
> - Rebased on top of linux-next
> - Fix min voltage on vdd_usb_3v3 regulator (ldo2) on j721e-som
> - Use 3-hex-digit format for pinctrl values
>
> Changes from v3:
> https://lore.kernel.org/all/20230417154832.216774-1-eblanc@baylibre.com/
> - Rebased on top of v6.5-rc1.
> - Change pinctrl number for irq pin as wkup_pmx0 was split on some boards.
> - Use already present wkup_i2c0 node instead of creating a new one.
>
> Changes from v2:
> https://lore.kernel.org/lkml/20230414112843.1358067-1-eblanc@baylibre.com/
> - Change node name as per Krzysztof review.
> - Add a fix for the interrupt range of wakeup gpio used by TPS6594 pmic
> on J784S4.
> The interruptions of the PMIC were not working before that.
> - Remove dependencies on other patch series as that was a mistake, see
> https://lore.kernel.org/lkml/CRYY2V3HJ0CP.96JQ18PLZB3C@burritosblues/
>
> Changes from v1:
> https://lore.kernel.org/lkml/20230329142948.833800-1-eblanc@baylibre.com/
> - Harmonize regulators names across the different boards.
> - Adjust AVS voltage range.
> - Remove some outdated comments.
> - Add PMIC to J784S4 board.
> - Compatible string modified to match dt-bindings.
> - Add gpio-controller and gpio-cells properties.
>
> Esteban Blanc (2):
> arm64: dts: ti: k3-j7200-som-p0: Add TP6594 family PMICs
> arm64: dts: ti: k3-j721s2-som-p0: Add TP6594 family PMICs
>
> Jerome Neanne (2):
> arm64: dts: ti: k3-j721e-som-p0: Add TP6594 family PMICs
> arm64: dts: ti: k3-j784s4-evm: Add support for TPS6594 PMIC
>
> Neha Malcom Francis (3):
> arm64: dts: ti: k3-am69-sk: Add support for TPS6594 PMIC
> arm64: dts: ti: k3-j721e-sk: Add TPS6594 family PMICs
> DONOTMERGE: arm64: defconfig: Enable TPS6594 PMIC for J7 devices
>
> arch/arm64/boot/dts/ti/k3-am69-sk.dts | 100 ++++++++++
> arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 157 +++++++++++++++
> arch/arm64/boot/dts/ti/k3-j721e-sk.dts | 154 ++++++++++++++
> arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi | 163 +++++++++++++++
> arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 199 +++++++++++++++++++
> arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 104 ++++++++++
> arch/arm64/configs/defconfig | 2 +-
> 7 files changed, 878 insertions(+), 1 deletion(-)
>
^ permalink raw reply [flat|nested] 12+ messages in thread* Re: [PATCH v8 0/7] Add TPS6594 PMIC support on several boards
2023-12-04 4:09 ` [PATCH v8 0/7] Add TPS6594 PMIC support on several boards Kumar, Udit
@ 2023-12-04 4:12 ` Neha Malcom Francis
0 siblings, 0 replies; 12+ messages in thread
From: Neha Malcom Francis @ 2023-12-04 4:12 UTC (permalink / raw)
To: Kumar, Udit, nm, vigneshr, kristo, robh+dt,
krzysztof.kozlowski+dt, conor+dt, a-nandan
Cc: linux-arm-kernel, devicetree, linux-kernel, eblanc, jneanne,
aseketeli, jpanis, j-luthra, vaishnav.a, hnagalla, devarsht
Hi Udit,
On 04/12/23 09:39, Kumar, Udit wrote:
>
> On 11/28/2023 11:22 AM, Neha Malcom Francis wrote:
>> TPS6594 is a Power Management IC which provides regulators and others
>> features like GPIOs, RTC, watchdog, ESMs (Error Signal Monitor), and
>> PFSM (Pre-configurable Finite State Machine). The SoC and the PMIC can
>> communicate through the I2C or SPI interfaces.
>> TPS6594 is the super-set device while TPS6593 and LP8764 are derivatives.
>
> Please consider adding bootph property in avs regulator node.
>
> Thanks
>
> Udit
>
Thanks for catching that, I'll send out v9 with the bootph property added.
>
>> This series adds device tree nodes for TI TPS6594 PMICs found in the
>> following boards:
>> - J721EXSOMXEVM:
>> Link: https://www.ti.com/tool/J721EXSOMXEVM
>> - J721S2XSOMXEVM:
>> Link: https://www.ti.com/tool/J721S2XSOMXEVM
>> - J7200XSOMXEVM:
>> Link: https://www.ti.com/tool/J7200XSOMXEVM
>> - J784S4XEVM
>> Link: https://www.ti.com/tool/J784S4XEVM
>> - SK-AM69
>> Link: https://www.ti.com/tool/SK-AM69
>> - SK-TDA4VM (J721E-SK)
>> Link: https://www.ti.com/tool/SK-TDA4VM
>>
>> Boot Logs with required config (DONOTMERGE patch) enabled:
>> https://gist.github.com/nehamalcom/f47fcd6183360ed8a146c9ba456202c3
>> Boot Logs without config enabled:
>> https://gist.github.com/nehamalcom/58217b100e614ae55726f314e02b5001
>>
>> ---
>> Changes from v7:
>> https://lore.kernel.org/all/20231122104513.2335757-1-n-francis@ti.com/
>> - (New Patches) Add support for SK boards that have TPS6594xx PMIC
>> present (J721E-SK and AM69-SK)
>> - Add DONOTMERGE defconfig patch to show test logs
>>
>> Changes from v6:
>> https://lore.kernel.org/all/20230810-tps6594-v6-0-2b2e2399e2ef@ti.com/
>> - Modify patch series to include only patches not merged (J7)
>> - Add boot logs for all affected boards
>>
>> Changes from v5:
>> https://lore.kernel.org/all/20230809-tps6594-v5-0-485fd3d63670@ti.com
>> - Range-diff: http://0x0.st/H_fD.diff
>> - Reword the patch fixing interrupt ranges for mcu domain gpio intr, and
>> add Fixes: tag
>> - Also fix interrupt ranges for main domain gpio intr in the same patch
>> - Change pinctrl node names to end in -pins to fix dtbs_check warnings
>> - (New Patch) Enable TPS6594 in defconfig
>>
>> Changes from v4:
>> https://lore.kernel.org/all/20230727130908.10656-1-eblanc@baylibre.com/
>> - Range-diff: https://0x0.st/H_L7.diff
>> - Rebased on top of linux-next
>> - Fix min voltage on vdd_usb_3v3 regulator (ldo2) on j721e-som
>> - Use 3-hex-digit format for pinctrl values
>>
>> Changes from v3:
>> https://lore.kernel.org/all/20230417154832.216774-1-eblanc@baylibre.com/
>> - Rebased on top of v6.5-rc1.
>> - Change pinctrl number for irq pin as wkup_pmx0 was split on some boards.
>> - Use already present wkup_i2c0 node instead of creating a new one.
>>
>> Changes from v2:
>> https://lore.kernel.org/lkml/20230414112843.1358067-1-eblanc@baylibre.com/
>> - Change node name as per Krzysztof review.
>> - Add a fix for the interrupt range of wakeup gpio used by TPS6594 pmic
>> on J784S4.
>> The interruptions of the PMIC were not working before that.
>> - Remove dependencies on other patch series as that was a mistake, see
>> https://lore.kernel.org/lkml/CRYY2V3HJ0CP.96JQ18PLZB3C@burritosblues/
>>
>> Changes from v1:
>> https://lore.kernel.org/lkml/20230329142948.833800-1-eblanc@baylibre.com/
>> - Harmonize regulators names across the different boards.
>> - Adjust AVS voltage range.
>> - Remove some outdated comments.
>> - Add PMIC to J784S4 board.
>> - Compatible string modified to match dt-bindings.
>> - Add gpio-controller and gpio-cells properties.
>>
>> Esteban Blanc (2):
>> arm64: dts: ti: k3-j7200-som-p0: Add TP6594 family PMICs
>> arm64: dts: ti: k3-j721s2-som-p0: Add TP6594 family PMICs
>>
>> Jerome Neanne (2):
>> arm64: dts: ti: k3-j721e-som-p0: Add TP6594 family PMICs
>> arm64: dts: ti: k3-j784s4-evm: Add support for TPS6594 PMIC
>>
>> Neha Malcom Francis (3):
>> arm64: dts: ti: k3-am69-sk: Add support for TPS6594 PMIC
>> arm64: dts: ti: k3-j721e-sk: Add TPS6594 family PMICs
>> DONOTMERGE: arm64: defconfig: Enable TPS6594 PMIC for J7 devices
>>
>> arch/arm64/boot/dts/ti/k3-am69-sk.dts | 100 ++++++++++
>> arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 157 +++++++++++++++
>> arch/arm64/boot/dts/ti/k3-j721e-sk.dts | 154 ++++++++++++++
>> arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi | 163 +++++++++++++++
>> arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 199 +++++++++++++++++++
>> arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 104 ++++++++++
>> arch/arm64/configs/defconfig | 2 +-
>> 7 files changed, 878 insertions(+), 1 deletion(-)
>>
--
Thanking You
Neha Malcom Francis
^ permalink raw reply [flat|nested] 12+ messages in thread