From: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
To: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>,
Marc Zyngier <maz@kernel.org>,
Thomas Gleixner <tglx@linutronix.de>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Philipp Zabel <p.zabel@pengutronix.de>,
"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
<devicetree@vger.kernel.org>,
Geert Uytterhoeven <geert+renesas@glider.be>,
Linux Kernel Mailing List <linux-kernel@vger.kernel.org>,
Linux-Renesas <linux-renesas-soc@vger.kernel.org>,
Biju Das <biju.das.jz@bp.renesas.com>
Subject: Re: [PATCH 1/2] dt-bindings: interrupt-controller: Add Renesas RZ/G2L Interrupt Controller
Date: Fri, 29 Apr 2022 10:52:15 +0100 [thread overview]
Message-ID: <CA+V-a8sWPAQBJ4ynTXgDfgsdcN9ZAVK8MuzbbkaX8EcRW-rB0Q@mail.gmail.com> (raw)
In-Reply-To: <CAMuHMdVARiVpch12HOMy8WR5pMnvVK-Mys8ZRnNK2u+y+qozJg@mail.gmail.com>
Hi Geert,
On Fri, Apr 29, 2022 at 9:44 AM Geert Uytterhoeven <geert@linux-m68k.org> wrote:
>
> Hi Prabhakar,
>
> On Fri, Apr 29, 2022 at 10:38 AM Lad, Prabhakar
> <prabhakar.csengg@gmail.com> wrote:
> > On Thu, Apr 28, 2022 at 10:32 AM Geert Uytterhoeven
> > > On Fri, Apr 22, 2022 at 12:12 AM Lad Prabhakar
> > > <prabhakar.mahadev-lad.rj@bp.renesas.com> wrote:
> > > > Add DT bindings for the Renesas RZ/G2L Interrupt Controller.
> > > >
> > > > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> > >
> > > Thanks for your patch!
> > >
> > > > --- /dev/null
> > > > +++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,rzg2l-irqc.yaml
> > > > @@ -0,0 +1,131 @@
> > > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > > > +%YAML 1.2
> > > > +---
> > > > +$id: http://devicetree.org/schemas/interrupt-controller/renesas,rzg2l-irqc.yaml#
> > > > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > > > +
> > > > +title: Renesas RZ/G2L (and alike SoC's) Interrupt Controller (IA55)
> > > > +
> > > > +maintainers:
> > > > + - Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> > > > + - Geert Uytterhoeven <geert+renesas@glider.be>
> > > > +
> > > > +description: |
> > > > + IA55 performs various interrupt controls including synchronization for the external
> > > > + interrupts of NMI, IRQ, and GPIOINT and the interrupts of the built-in peripheral
> > > > + interrupts output by each IP. And it notifies the interrupt to the GIC
> > > > + - IRQ sense select for 8 external interrupts, mapped to 8 GIC SPI interrupts
> > > > + - GPIO pins used as external interrupt input pins, mapped to 32 GIC SPI interrupts
> > > > + - NMI edge select (NMI is not treated as NMI exception and supports fall edge and
> > > > + stand-up edge detection interrupts)
> > > > +
> > > > +allOf:
> > > > + - $ref: /schemas/interrupt-controller.yaml#
> > > > +
> > > > +properties:
> > > > + compatible:
> > > > + items:
> > > > + - enum:
> > > > + - renesas,r9a07g044-irqc # RZ/G2L
> > > > + - const: renesas,rzg2l-irqc
> > > > +
> > > > + '#interrupt-cells':
> > > > + const: 2
> > >
> > > What is the meaning of the cells? IRQ number + flags, I assume?
> > IRQ number and the type.
> >
> > > How are the numbers mapped, do you need a DT bindings header?
> > No, just plain numbers are used (driver handles the validation of the
> > interrupt numbering), for example like below,
> >
> > ð0 {
> > ...
> > status = "okay";
> >
> > phy0: ethernet-phy@7 {
> > compatible = "ethernet-phy-id0022.1640",
> > "ethernet-phy-ieee802.3-c22";
> > reg = <7>;
> > interrupt-parent = <&irqc>;
> > interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
>
> OK, so the number must be an external interrupt number (0..7).
>
Yep that's right.
> > ...
> > };
> > };
> >
> > And for the GPIO:
> >
> > key-1 {
> > gpios = <&pinctrl RZG2L_GPIO(43, 0) GPIO_ACTIVE_HIGH>;
> > linux,code = <KEY_1>;
> > linux,input-type = <EV_KEY>;
> > wakeup-source;
> > label = "SW1";
> > };
>
> OK, so in this case the interrupt number is obtained implicitly, and
> no interrupts property is used.
>
Indeed.
> > > Perhaps it would make sense to increase to 3 cells, so you can use
> > > one cell for the type (cfr. e.g. GIC_SPI), and the second for the
> > > plain index within the type?
> > >
> > Could you please elaborate on this. Are you referring to the type here
> > as the type to be set up in the GIC?
>
> Please ignore, you don't need the type, as it's always an external
> interrupt number, right?
>
Yep that's right.
Cheers,
Prabhakar
> Gr{oetje,eeting}s,
>
> Geert
>
> --
> Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
>
> In personal conversations with technical people, I call myself a hacker. But
> when I'm talking to journalists I just say "programmer" or something like that.
> -- Linus Torvalds
next prev parent reply other threads:[~2022-04-29 9:52 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-04-21 22:11 [PATCH 0/2] Renesas RZ/G2L IRQC support Lad Prabhakar
2022-04-21 22:11 ` [PATCH 1/2] dt-bindings: interrupt-controller: Add Renesas RZ/G2L Interrupt Controller Lad Prabhakar
2022-04-28 9:32 ` Geert Uytterhoeven
2022-04-29 8:37 ` Lad, Prabhakar
2022-04-29 8:44 ` Geert Uytterhoeven
2022-04-29 9:52 ` Lad, Prabhakar [this message]
2022-05-02 20:50 ` Rob Herring
2022-04-21 22:11 ` [PATCH 2/2] irqchip: Add RZ/G2L IA55 Interrupt Controller driver Lad Prabhakar
2022-04-28 9:42 ` Geert Uytterhoeven
2022-04-29 9:43 ` Lad, Prabhakar
2022-04-29 9:53 ` Geert Uytterhoeven
2022-04-29 9:59 ` Lad, Prabhakar
2022-05-02 5:21 ` Lad, Prabhakar
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=CA+V-a8sWPAQBJ4ynTXgDfgsdcN9ZAVK8MuzbbkaX8EcRW-rB0Q@mail.gmail.com \
--to=prabhakar.csengg@gmail.com \
--cc=biju.das.jz@bp.renesas.com \
--cc=devicetree@vger.kernel.org \
--cc=geert+renesas@glider.be \
--cc=geert@linux-m68k.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-renesas-soc@vger.kernel.org \
--cc=maz@kernel.org \
--cc=p.zabel@pengutronix.de \
--cc=prabhakar.mahadev-lad.rj@bp.renesas.com \
--cc=robh+dt@kernel.org \
--cc=tglx@linutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).