[PATCH 0/4] dt-bindings: pinctrl: convert remaining qcom bindings to yaml

[PATCH 0/4] dt-bindings: pinctrl: convert remaining qcom bindings to yaml

[Rayyan Ansari]

Hi,
The following patches convert all remaining old text bindings for
Qualcomm pinctrl to yaml, so device trees can be validated against the
schema.

Thanks,
Rayyan

Rayyan Ansari (4):
  dt-bindings: pinctrl: qcom,apq8064-pinctrl: convert to dtschema
  dt-bindings: pinctrl: qcom,ipq8064-pinctrl: convert to dtschema
  dt-bindings: pinctrl: qcom,ipq4019-pinctrl: convert to dtschema
  dt-bindings: pinctrl: qcom,apq8084-pinctrl: convert to dtschema

 .../bindings/pinctrl/qcom,apq8064-pinctrl.txt |  95 ---------
 .../pinctrl/qcom,apq8064-pinctrl.yaml         | 110 ++++++++++
 .../bindings/pinctrl/qcom,apq8084-pinctrl.txt | 188 ------------------
 .../pinctrl/qcom,apq8084-pinctrl.yaml         | 129 ++++++++++++
 .../bindings/pinctrl/qcom,ipq4019-pinctrl.txt |  85 --------
 .../pinctrl/qcom,ipq4019-pinctrl.yaml         | 102 ++++++++++
 .../bindings/pinctrl/qcom,ipq8064-pinctrl.txt | 101 ----------
 .../pinctrl/qcom,ipq8064-pinctrl.yaml         | 108 ++++++++++
 8 files changed, 449 insertions(+), 469 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt
 create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.yaml
 delete mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt
 create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.yaml
 delete mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.txt
 create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.yaml
 delete mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt
 create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.yaml

-- 
2.45.2

[PATCH 1/4] dt-bindings: pinctrl: qcom,apq8064-pinctrl: convert to dtschema

[Rayyan Ansari]

Convert the Qualcomm APQ8064 TLMM block bindings from text to yaml dt
schema format.

Signed-off-by: Rayyan Ansari <rayyan.ansari@linaro.org>
---
 .../bindings/pinctrl/qcom,apq8064-pinctrl.txt |  95 ---------------
 .../pinctrl/qcom,apq8064-pinctrl.yaml         | 110 ++++++++++++++++++
 2 files changed, 110 insertions(+), 95 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt
 create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.yaml

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt
deleted file mode 100644
index 4e90ddd77784..000000000000
--- a/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt
+++ /dev/null
@@ -1,95 +0,0 @@
-Qualcomm APQ8064 TLMM block
-
-Required properties:
-- compatible: "qcom,apq8064-pinctrl"
-- reg: Should be the base address and length of the TLMM block.
-- interrupts: Should be the parent IRQ of the TLMM block.
-- interrupt-controller: Marks the device node as an interrupt controller.
-- #interrupt-cells: Should be two.
-- gpio-controller: Marks the device node as a GPIO controller.
-- #gpio-cells : Should be two.
-                The first cell is the gpio pin number and the
-                second cell is used for optional parameters.
-- gpio-ranges: see ../gpio/gpio.txt
-
-Optional properties:
-
-- gpio-reserved-ranges: see ../gpio/gpio.txt
-
-Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
-a general description of GPIO and interrupt bindings.
-
-Please refer to pinctrl-bindings.txt in this directory for details of the
-common pinctrl bindings used by client devices, including the meaning of the
-phrase "pin configuration node".
-
-Qualcomm's pin configuration nodes act as a container for an arbitrary number of
-subnodes. Each of these subnodes represents some desired configuration for a
-pin, a group, or a list of pins or groups. This configuration can include the
-mux function to select on those pin(s)/group(s), and various pin configuration
-parameters, such as pull-up, drive strength, etc.
-
-The name of each subnode is not important; all subnodes should be enumerated
-and processed purely based on their content.
-
-Each subnode only affects those parameters that are explicitly listed. In
-other words, a subnode that lists a mux function but no pin configuration
-parameters implies no information about any pin configuration parameters.
-Similarly, a pin subnode that describes a pullup parameter implies no
-information about e.g. the mux function.
-
-
-The following generic properties as defined in pinctrl-bindings.txt are valid
-to specify in a pin configuration subnode:
-
- pins, function, bias-disable, bias-pull-down, bias-pull-up, drive-strength,
- output-low, output-high.
-
-Non-empty subnodes must specify the 'pins' property.
-
-Valid values for pins are:
-  gpio0-gpio89
-
-Valid values for function are:
-  cam_mclk, codec_mic_i2s, codec_spkr_i2s, gp_clk_0a, gp_clk_0b, gp_clk_1a,
-  gp_clk_1b, gp_clk_2a, gp_clk_2b, gpio, gsbi1, gsbi2, gsbi3, gsbi4,
-  gsbi4_cam_i2c, gsbi5, gsbi5_spi_cs1, gsbi5_spi_cs2, gsbi5_spi_cs3, gsbi6,
-  gsbi6_spi_cs1, gsbi6_spi_cs2, gsbi6_spi_cs3, gsbi7, gsbi7_spi_cs1,
-  gsbi7_spi_cs2, gsbi7_spi_cs3, gsbi_cam_i2c, hdmi, mi2s, riva_bt, riva_fm,
-  riva_wlan, sdc2, sdc4, slimbus, spkr_i2s, tsif1, tsif2, usb2_hsic, ps_hold
-
-Example:
-
-	msmgpio: pinctrl@800000 {
-		compatible = "qcom,apq8064-pinctrl";
-		reg = <0x800000 0x4000>;
-
-		gpio-controller;
-		#gpio-cells = <2>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-		interrupts = <0 16 0x4>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&gsbi5_uart_default>;
-		gpio-ranges = <&msmgpio 0 0 90>;
-
-		gsbi5_uart_default: gsbi5_uart_default {
-			mux {
-				pins = "gpio51", "gpio52";
-				function = "gsbi5";
-			};
-
-			tx {
-				pins = "gpio51";
-				drive-strength = <4>;
-				bias-disable;
-			};
-
-			rx {
-				pins = "gpio52";
-				drive-strength = <2>;
-				bias-pull-up;
-			};
-		};
-	};
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.yaml
new file mode 100644
index 000000000000..f251dcd4bb7f
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.yaml
@@ -0,0 +1,110 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/qcom,apq8064-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Technologies, Inc. APQ8064 TLMM block
+
+maintainers:
+  - Bjorn Andersson <bjorn.andersson@linaro.org>
+
+description: |
+  Top Level Mode Multiplexer pin controller in Qualcomm APQ8064 SoC.
+
+allOf:
+  - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
+
+properties:
+  compatible:
+    const: qcom,apq8064-pinctrl
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  gpio-reserved-ranges: true
+
+patternProperties:
+  "-state$":
+    oneOf:
+      - $ref: "#/$defs/qcom-apq8064-tlmm-state"
+      - patternProperties:
+          "-pins$":
+            $ref: "#/$defs/qcom-apq8064-tlmm-state"
+        additionalProperties: false
+
+$defs:
+  qcom-apq8064-tlmm-state:
+    type: object
+    description:
+      Pinctrl node's client devices use subnodes for desired pin configuration.
+      Client device subnodes use below standard properties.
+    $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
+    unevaluatedProperties: false
+
+    properties:
+      pins:
+        description:
+          List of gpio pins affected by the properties specified in this
+          subnode.
+        items:
+          oneOf:
+            - pattern: "^gpio([0-9]|[1-8][0-9])$"
+            - enum: [ sdc1_clk, sdc1_cmd, sdc1_data, sdc3_clk, sdc3_cmd, sdc3_data ]
+        minItems: 1
+        maxItems: 36
+
+      function:
+        description:
+          Specify the alternative function to be configured for the specified
+          pins.
+        enum: [ cam_mclk, codec_mic_i2s, codec_spkr_i2s, gp_clk_0a,
+                gp_clk_0b, gp_clk_1a, gp_clk_1b, gp_clk_2a, gp_clk_2b,
+                gpio, gsbi1, gsbi2, gsbi3, gsbi4, gsbi4_cam_i2c,
+                gsbi5, gsbi5_spi_cs1, gsbi5_spi_cs2, gsbi5_spi_cs3,
+                gsbi6, gsbi6_spi_cs1, gsbi6_spi_cs2, gsbi6_spi_cs3,
+                gsbi7, gsbi7_spi_cs1, gsbi7_spi_cs2, gsbi7_spi_cs3,
+                gsbi_cam_i2c, hdmi, mi2s, riva_bt, riva_fm, riva_wlan,
+                sdc2, sdc4, slimbus, spkr_i2s, tsif1, tsif2, usb2_hsic,
+                ps_hold ]
+
+    required:
+      - pins
+
+required:
+  - compatible
+  - reg
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    tlmm: pinctrl@800000 {
+        compatible = "qcom,apq8064-pinctrl";
+        reg = <0x800000 0x4000>;
+
+        gpio-controller;
+        #gpio-cells = <2>;
+        gpio-ranges = <&tlmm 0 0 90>;
+        interrupt-controller;
+        #interrupt-cells = <2>;
+        interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+
+        uart-state {
+            rx-pins {
+                pins = "gpio52";
+                function = "gsbi5";
+                bias-pull-up;
+            };
+
+            tx-pins {
+                pins = "gpio51";
+                function = "gsbi5";
+                bias-disable;
+            };
+        };
+    };
-- 
2.45.2

[PATCH 2/4] dt-bindings: pinctrl: qcom,ipq8064-pinctrl: convert to dtschema

[Rayyan Ansari]

Convert the Qualcomm IPQ8064 TLMM block bindings from text to yaml dt
schema format.

Signed-off-by: Rayyan Ansari <rayyan.ansari@linaro.org>
---
 .../bindings/pinctrl/qcom,ipq8064-pinctrl.txt | 101 ----------------
 .../pinctrl/qcom,ipq8064-pinctrl.yaml         | 108 ++++++++++++++++++
 2 files changed, 108 insertions(+), 101 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt
 create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.yaml

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt
deleted file mode 100644
index a7aaaa7db83b..000000000000
--- a/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt
+++ /dev/null
@@ -1,101 +0,0 @@
-Qualcomm IPQ8064 TLMM block
-
-Required properties:
-- compatible: "qcom,ipq8064-pinctrl"
-- reg: Should be the base address and length of the TLMM block.
-- interrupts: Should be the parent IRQ of the TLMM block.
-- interrupt-controller: Marks the device node as an interrupt controller.
-- #interrupt-cells: Should be two.
-- gpio-controller: Marks the device node as a GPIO controller.
-- #gpio-cells : Should be two.
-                The first cell is the gpio pin number and the
-                second cell is used for optional parameters.
-- gpio-ranges: see ../gpio/gpio.txt
-
-Optional properties:
-
-- gpio-reserved-ranges: see ../gpio/gpio.txt
-
-Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
-a general description of GPIO and interrupt bindings.
-
-Please refer to pinctrl-bindings.txt in this directory for details of the
-common pinctrl bindings used by client devices, including the meaning of the
-phrase "pin configuration node".
-
-Qualcomm's pin configuration nodes act as a container for an arbitrary number of
-subnodes. Each of these subnodes represents some desired configuration for a
-pin, a group, or a list of pins or groups. This configuration can include the
-mux function to select on those pin(s)/group(s), and various pin configuration
-parameters, such as pull-up, drive strength, etc.
-
-The name of each subnode is not important; all subnodes should be enumerated
-and processed purely based on their content.
-
-Each subnode only affects those parameters that are explicitly listed. In
-other words, a subnode that lists a mux function but no pin configuration
-parameters implies no information about any pin configuration parameters.
-Similarly, a pin subnode that describes a pullup parameter implies no
-information about e.g. the mux function.
-
-
-The following generic properties as defined in pinctrl-bindings.txt are valid
-to specify in a pin configuration subnode:
-
- pins, function, bias-disable, bias-pull-down, bias-pull-up, drive-strength,
- output-low, output-high.
-
-Non-empty subnodes must specify the 'pins' property.
-
-Valid values for qcom,pins are:
-  gpio0-gpio68
-   Supports mux, bias, and drive-strength
-
-  sdc3_clk, sdc3_cmd, sdc3_data
-   Supports bias and drive-strength
-
-
-Valid values for function are:
-  mdio, mi2s, pdm, ssbi, spmi, audio_pcm, gpio, gsbi1, gsbi2, gsbi4, gsbi5,
-  gsbi5_spi_cs1, gsbi5_spi_cs2, gsbi5_spi_cs3, gsbi6, gsbi7, nss_spi, sdc1,
-  spdif, nand, tsif1, tsif2, usb_fs_n, usb_fs, usb2_hsic, rgmii2, sata,
-  pcie1_rst, pcie1_prsnt, pcie1_pwren_n, pcie1_pwren, pcie1_pwrflt,
-  pcie1_clk_req, pcie2_rst, pcie2_prsnt, pcie2_pwren_n, pcie2_pwren,
-  pcie2_pwrflt, pcie2_clk_req, pcie3_rst, pcie3_prsnt, pcie3_pwren_n,
-  pcie3_pwren, pcie3_pwrflt, pcie3_clk_req, ps_hold
-
-Example:
-
-	pinmux: pinctrl@800000 {
-		compatible = "qcom,ipq8064-pinctrl";
-		reg = <0x800000 0x4000>;
-
-		gpio-controller;
-		#gpio-cells = <2>;
-		gpio-ranges = <&pinmux 0 0 69>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-		interrupts = <0 32 0x4>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&gsbi5_uart_default>;
-
-		gsbi5_uart_default: gsbi5_uart_default {
-			mux {
-				pins = "gpio18", "gpio19";
-				function = "gsbi5";
-			};
-
-			tx {
-				pins = "gpio18";
-				drive-strength = <4>;
-				bias-disable;
-			};
-
-			rx {
-				pins = "gpio19";
-				drive-strength = <2>;
-				bias-pull-up;
-			};
-		};
-	};
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.yaml
new file mode 100644
index 000000000000..58f11e1bdd4f
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.yaml
@@ -0,0 +1,108 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/qcom,ipq8064-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Technologies, Inc. IPQ8064 TLMM block
+
+maintainers:
+  - Bjorn Andersson <bjorn.andersson@linaro.org>
+
+description: |
+  Top Level Mode Multiplexer pin controller in Qualcomm IPQ8064 SoC.
+
+allOf:
+  - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
+
+properties:
+  compatible:
+    const: qcom,ipq8064-pinctrl
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  gpio-reserved-ranges: true
+
+patternProperties:
+  "-state$":
+    oneOf:
+      - $ref: "#/$defs/qcom-ipq8064-tlmm-state"
+      - patternProperties:
+          "-pins$":
+            $ref: "#/$defs/qcom-ipq8064-tlmm-state"
+        additionalProperties: false
+
+$defs:
+  qcom-ipq8064-tlmm-state:
+    type: object
+    description:
+      Pinctrl node's client devices use subnodes for desired pin configuration.
+      Client device subnodes use below standard properties.
+    $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
+    unevaluatedProperties: false
+
+    properties:
+      pins:
+        description:
+          List of gpio pins affected by the properties specified in this
+          subnode.
+        items:
+          oneOf:
+            - pattern: "^gpio([0-9]|[1-5][0-9]|6[0-8])$"
+            - enum: [ sdc3_clk, sdc3_cmd, sdc3_data ]
+        minItems: 1
+        maxItems: 36
+
+      function:
+        description:
+          Specify the alternative function to be configured for the specified
+          pins.
+        enum: [ mdio, mi2s, pdm, ssbi, spmi, audio_pcm, gpio, gsbi1, gsbi2, gsbi4, gsbi5,
+                gsbi5_spi_cs1, gsbi5_spi_cs2, gsbi5_spi_cs3, gsbi6, gsbi7, nss_spi, sdc1,
+                spdif, nand, tsif1, tsif2, usb_fs_n, usb_fs, usb2_hsic, rgmii2, sata,
+                pcie1_rst, pcie1_prsnt, pcie1_pwren_n, pcie1_pwren, pcie1_pwrflt,
+                pcie1_clk_req, pcie2_rst, pcie2_prsnt, pcie2_pwren_n, pcie2_pwren,
+                pcie2_pwrflt, pcie2_clk_req, pcie3_rst, pcie3_prsnt, pcie3_pwren_n,
+                pcie3_pwren, pcie3_pwrflt, pcie3_clk_req, ps_hold ]
+
+    required:
+      - pins
+
+required:
+  - compatible
+  - reg
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    tlmm: pinctrl@800000 {
+        compatible = "qcom,ipq8064-pinctrl";
+        reg = <0x00800000 0x4000>;
+
+        gpio-controller;
+        #gpio-cells = <2>;
+        gpio-ranges = <&tlmm 0 0 69>;
+        interrupt-controller;
+        #interrupt-cells = <2>;
+        interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+
+        uart-state {
+            rx-pins {
+                pins = "gpio19";
+                function = "gsbi5";
+                bias-pull-up;
+            };
+
+            tx-pins {
+                pins = "gpio18";
+                function = "gsbi5";
+                bias-disable;
+            };
+        };
+    };
-- 
2.45.2

[PATCH 3/4] dt-bindings: pinctrl: qcom,ipq4019-pinctrl: convert to dtschema

[Rayyan Ansari]

Convert the Qualcomm IPQ4019 TLMM block bindings from text to yaml dt
schema format.

Signed-off-by: Rayyan Ansari <rayyan.ansari@linaro.org>
---
 .../bindings/pinctrl/qcom,ipq4019-pinctrl.txt |  85 ---------------
 .../pinctrl/qcom,ipq4019-pinctrl.yaml         | 102 ++++++++++++++++++
 2 files changed, 102 insertions(+), 85 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.txt
 create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.yaml

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.txt
deleted file mode 100644
index 97858a7c07a2..000000000000
--- a/Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.txt
+++ /dev/null
@@ -1,85 +0,0 @@
-Qualcomm Atheros IPQ4019 TLMM block
-
-This is the Top Level Mode Multiplexor block found on the Qualcomm IPQ8019
-platform, it provides pinctrl, pinmux, pinconf, and gpiolib facilities.
-
-Required properties:
-- compatible: "qcom,ipq4019-pinctrl"
-- reg: Should be the base address and length of the TLMM block.
-- interrupts: Should be the parent IRQ of the TLMM block.
-- interrupt-controller: Marks the device node as an interrupt controller.
-- #interrupt-cells: Should be two.
-- gpio-controller: Marks the device node as a GPIO controller.
-- #gpio-cells : Should be two.
-                The first cell is the gpio pin number and the
-                second cell is used for optional parameters.
-- gpio-ranges: see ../gpio/gpio.txt
-
-Optional properties:
-
-- gpio-reserved-ranges: see ../gpio/gpio.txt
-
-Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
-a general description of GPIO and interrupt bindings.
-
-Please refer to pinctrl-bindings.txt in this directory for details of the
-common pinctrl bindings used by client devices, including the meaning of the
-phrase "pin configuration node".
-
-The pin configuration nodes act as a container for an arbitrary number of
-subnodes. Each of these subnodes represents some desired configuration for a
-pin, a group, or a list of pins or groups. This configuration can include the
-mux function to select on those pin(s)/group(s), and various pin configuration
-parameters, such as pull-up, drive strength, etc.
-
-The name of each subnode is not important; all subnodes should be enumerated
-and processed purely based on their content.
-
-Each subnode only affects those parameters that are explicitly listed. In
-other words, a subnode that lists a mux function but no pin configuration
-parameters implies no information about any pin configuration parameters.
-Similarly, a pin subnode that describes a pullup parameter implies no
-information about e.g. the mux function.
-
-
-The following generic properties as defined in pinctrl-bindings.txt are valid
-to specify in a pin configuration subnode:
- pins, function, bias-disable, bias-pull-down, bias-pull-up, drive-open-drain,
- drive-strength.
-
-Non-empty subnodes must specify the 'pins' property.
-Note that not all properties are valid for all pins.
-
-
-Valid values for qcom,pins are:
-  gpio0-gpio99
-    Supports mux, bias and drive-strength
-
-Valid values for qcom,function are:
-aud_pin, audio_pwm, blsp_i2c0, blsp_i2c1, blsp_spi0, blsp_spi1, blsp_uart0,
-blsp_uart1, chip_rst, gpio, i2s_rx, i2s_spdif_in, i2s_spdif_out, i2s_td, i2s_tx,
-jtag, led0, led1, led2, led3, led4, led5, led6, led7, led8, led9, led10, led11,
-mdc, mdio, pcie, pmu, prng_rosc, qpic, rgmii, rmii, sdio, smart0, smart1,
-smart2, smart3, tm, wifi0, wifi1
-
-Example:
-
-	tlmm: pinctrl@1000000 {
-		compatible = "qcom,ipq4019-pinctrl";
-		reg = <0x1000000 0x300000>;
-
-		gpio-controller;
-		#gpio-cells = <2>;
-		gpio-ranges = <&tlmm 0 0 100>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-		interrupts = <0 208 0>;
-
-		serial_pins: serial_pinmux {
-			mux {
-				pins = "gpio60", "gpio61";
-				function = "blsp_uart0";
-				bias-disable;
-			};
-		};
-	};
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.yaml
new file mode 100644
index 000000000000..ebf74e48ec5b
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.yaml
@@ -0,0 +1,102 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/qcom,ipq4019-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Technologies, Inc. IPQ4019 TLMM block
+
+maintainers:
+  - Bjorn Andersson <bjorn.andersson@linaro.org>
+
+description: |
+  Top Level Mode Multiplexer pin controller in Qualcomm IPQ4019 SoC.
+
+allOf:
+  - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
+
+properties:
+  compatible:
+    const: qcom,ipq4019-pinctrl
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  gpio-reserved-ranges: true
+
+patternProperties:
+  "-state$":
+    oneOf:
+      - $ref: "#/$defs/qcom-ipq4019-tlmm-state"
+      - patternProperties:
+          "-pins$":
+            $ref: "#/$defs/qcom-ipq4019-tlmm-state"
+        additionalProperties: false
+
+  "-hog(-[0-9]+)?$":
+    required:
+      - gpio-hog
+
+$defs:
+  qcom-ipq4019-tlmm-state:
+    type: object
+    description:
+      Pinctrl node's client devices use subnodes for desired pin configuration.
+      Client device subnodes use below standard properties.
+    $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
+    unevaluatedProperties: false
+
+    properties:
+      pins:
+        description:
+          List of gpio pins affected by the properties specified in this
+          subnode.
+        items:
+          pattern: "^gpio([0-9]|[1-9][0-9])$"
+        minItems: 1
+        maxItems: 36
+
+      function:
+        description:
+          Specify the alternative function to be configured for the specified
+          pins.
+        enum: [ aud_pin, audio_pwm, blsp_i2c0, blsp_i2c1, blsp_spi0,
+                blsp_spi1, blsp_uart0, blsp_uart1, chip_rst, gpio,
+                i2s_rx, i2s_spdif_in, i2s_spdif_out, i2s_td, i2s_tx,
+                jtag, led0, led1, led2, led3, led4, led5, led6, led7,
+                led8, led9, led10, led11, mdc, mdio, pcie, pmu,
+                prng_rosc, qpic, rgmii, rmii, sdio, smart0, smart1,
+                smart2, smart3, tm, wifi0, wifi1 ]
+
+    required:
+      - pins
+
+required:
+  - compatible
+  - reg
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    tlmm: pinctrl@1000000 {
+        compatible = "qcom,ipq4019-pinctrl";
+        reg = <0x01000000 0x300000>;
+
+        gpio-controller;
+        #gpio-cells = <2>;
+        gpio-ranges = <&tlmm 0 0 100>;
+        interrupt-controller;
+        #interrupt-cells = <2>;
+        interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+
+        uart-state {
+            pins = "gpio16", "gpio17";
+            function = "blsp_uart0";
+            bias-disable;
+        };
+    };
-- 
2.45.2

[PATCH 4/4] dt-bindings: pinctrl: qcom,apq8084-pinctrl: convert to dtschema

[Rayyan Ansari]

Convert the Qualcomm APQ8084 TLMM block bindings from text to yaml dt
schema format.

Signed-off-by: Rayyan Ansari <rayyan.ansari@linaro.org>
---
 .../bindings/pinctrl/qcom,apq8084-pinctrl.txt | 188 ------------------
 .../pinctrl/qcom,apq8084-pinctrl.yaml         | 129 ++++++++++++
 2 files changed, 129 insertions(+), 188 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt
 create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.yaml

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt
deleted file mode 100644
index c9782397ff14..000000000000
--- a/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt
+++ /dev/null
@@ -1,188 +0,0 @@
-Qualcomm APQ8084 TLMM block
-
-This binding describes the Top Level Mode Multiplexer block found in the
-MSM8960 platform.
-
-- compatible:
-	Usage: required
-	Value type: <string>
-	Definition: must be "qcom,apq8084-pinctrl"
-
-- reg:
-	Usage: required
-	Value type: <prop-encoded-array>
-	Definition: the base address and size of the TLMM register space.
-
-- interrupts:
-	Usage: required
-	Value type: <prop-encoded-array>
-	Definition: should specify the TLMM summary IRQ.
-
-- interrupt-controller:
-	Usage: required
-	Value type: <none>
-	Definition: identifies this node as an interrupt controller
-
-- #interrupt-cells:
-	Usage: required
-	Value type: <u32>
-	Definition: must be 2. Specifying the pin number and flags, as defined
-		    in <dt-bindings/interrupt-controller/irq.h>
-
-- gpio-controller:
-	Usage: required
-	Value type: <none>
-	Definition: identifies this node as a gpio controller
-
-- #gpio-cells:
-	Usage: required
-	Value type: <u32>
-	Definition: must be 2. Specifying the pin number and flags, as defined
-		    in <dt-bindings/gpio/gpio.h>
-
-- gpio-ranges:
-	Usage: required
-	Definition:  see ../gpio/gpio.txt
-
-- gpio-reserved-ranges:
-	Usage: optional
-	Definition: see ../gpio/gpio.txt
-
-Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
-a general description of GPIO and interrupt bindings.
-
-Please refer to pinctrl-bindings.txt in this directory for details of the
-common pinctrl bindings used by client devices, including the meaning of the
-phrase "pin configuration node".
-
-The pin configuration nodes act as a container for an arbitrary number of
-subnodes. Each of these subnodes represents some desired configuration for a
-pin, a group, or a list of pins or groups. This configuration can include the
-mux function to select on those pin(s)/group(s), and various pin configuration
-parameters, such as pull-up, drive strength, etc.
-
-
-PIN CONFIGURATION NODES:
-
-The name of each subnode is not important; all subnodes should be enumerated
-and processed purely based on their content.
-
-Each subnode only affects those parameters that are explicitly listed. In
-other words, a subnode that lists a mux function but no pin configuration
-parameters implies no information about any pin configuration parameters.
-Similarly, a pin subnode that describes a pullup parameter implies no
-information about e.g. the mux function.
-
-
-The following generic properties as defined in pinctrl-bindings.txt are valid
-to specify in a pin configuration subnode:
-
-- pins:
-	Usage: required
-	Value type: <string-array>
-	Definition: List of gpio pins affected by the properties specified in
-		    this subnode.  Valid pins are:
-		    gpio0-gpio146,
-		    sdc1_clk,
-		    sdc1_cmd,
-		    sdc1_data
-		    sdc2_clk,
-		    sdc2_cmd,
-		    sdc2_data
-
-- function:
-	Usage: required
-	Value type: <string>
-	Definition: Specify the alternative function to be configured for the
-		    specified pins. Functions are only valid for gpio pins.
-		    Valid values are:
-		    adsp_ext, audio_ref, blsp_i2c1, blsp_i2c2, blsp_i2c3,
-		    blsp_i2c4, blsp_i2c5, blsp_i2c6, blsp_i2c7, blsp_i2c8,
-		    blsp_i2c9, blsp_i2c10, blsp_i2c11, blsp_i2c12,
-		    blsp_spi1, blsp_spi2, blsp_spi3, blsp_spi4, blsp_spi5,
-		    blsp_spi6, blsp_spi7, blsp_spi8, blsp_spi9, blsp_spi10,
-		    blsp_spi11, blsp_spi12, blsp_uart1, blsp_uart2, blsp_uart3,
-		    blsp_uart4, blsp_uart5, blsp_uart6, blsp_uart7, blsp_uart8,
-		    blsp_uart9, blsp_uart10, blsp_uart11, blsp_uart12,
-		    blsp_uim1, blsp_uim2, blsp_uim3, blsp_uim4, blsp_uim5,
-		    blsp_uim6, blsp_uim7, blsp_uim8, blsp_uim9, blsp_uim10,
-		    blsp_uim11, blsp_uim12, cam_mclk0, cam_mclk1, cam_mclk2,
-		    cam_mclk3, cci_async, cci_async_in0, cci_i2c0, cci_i2c1,
-		    cci_timer0, cci_timer1, cci_timer2, cci_timer3, cci_timer4,
-		    edp_hpd, gcc_gp1, gcc_gp2, gcc_gp3, gcc_obt, gcc_vtt,i
-		    gp_mn, gp_pdm0, gp_pdm1, gp_pdm2, gp0_clk, gp1_clk, gpio,
-		    hdmi_cec, hdmi_ddc, hdmi_dtest, hdmi_hpd, hdmi_rcv, hsic,
-		    ldo_en, ldo_update, mdp_vsync, pci_e0, pci_e0_n, pci_e0_rst,
-		    pci_e1, pci_e1_rst, pci_e1_rst_n, pci_e1_clkreq_n, pri_mi2s,
-		    qua_mi2s, sata_act, sata_devsleep, sata_devsleep_n,
-		    sd_write, sdc_emmc_mode, sdc3, sdc4, sec_mi2s, slimbus,
-		    spdif_tx, spkr_i2s, spkr_i2s_ws, spss_geni, ter_mi2s, tsif1,
-		    tsif2, uim, uim_batt_alarm
-
-- bias-disable:
-	Usage: optional
-	Value type: <none>
-	Definition: The specified pins should be configured as no pull.
-
-- bias-pull-down:
-	Usage: optional
-	Value type: <none>
-	Definition: The specified pins should be configured as pull down.
-
-- bias-pull-up:
-	Usage: optional
-	Value type: <none>
-	Definition: The specified pins should be configured as pull up.
-
-- output-high:
-	Usage: optional
-	Value type: <none>
-	Definition: The specified pins are configured in output mode, driven
-		    high.
-		    Not valid for sdc pins.
-
-- output-low:
-	Usage: optional
-	Value type: <none>
-	Definition: The specified pins are configured in output mode, driven
-		    low.
-		    Not valid for sdc pins.
-
-- drive-strength:
-	Usage: optional
-	Value type: <u32>
-	Definition: Selects the drive strength for the specified pins, in mA.
-		    Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
-
-Example:
-
-	tlmm: pinctrl@fd510000 {
-		compatible = "qcom,apq8084-pinctrl";
-		reg = <0xfd510000 0x4000>;
-
-		gpio-controller;
-		#gpio-cells = <2>;
-		gpio-ranges = <&tlmm 0 0 147>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-		interrupts = <0 208 0>;
-
-		uart2: uart2-default {
-			mux {
-				pins = "gpio4", "gpio5";
-				function = "blsp_uart2";
-			};
-
-			tx {
-				pins = "gpio4";
-				drive-strength = <4>;
-				bias-disable;
-			};
-
-			rx {
-				pins = "gpio5";
-				drive-strength = <2>;
-				bias-pull-up;
-			};
-		};
-	};
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.yaml
new file mode 100644
index 000000000000..38877d8b97ff
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.yaml
@@ -0,0 +1,129 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/qcom,apq8084-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Technologies, Inc. APQ8084 TLMM block
+
+maintainers:
+  - Bjorn Andersson <bjorn.andersson@linaro.org>
+
+description: |
+  Top Level Mode Multiplexer pin controller in Qualcomm APQ8084 SoC.
+
+allOf:
+  - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
+
+properties:
+  compatible:
+    const: qcom,apq8084-pinctrl
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  gpio-reserved-ranges: true
+
+patternProperties:
+  "-state$":
+    oneOf:
+      - $ref: "#/$defs/qcom-apq8084-tlmm-state"
+      - patternProperties:
+          "-pins$":
+            $ref: "#/$defs/qcom-apq8084-tlmm-state"
+        additionalProperties: false
+
+$defs:
+  qcom-apq8084-tlmm-state:
+    type: object
+    description:
+      Pinctrl node's client devices use subnodes for desired pin configuration.
+      Client device subnodes use below standard properties.
+    $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
+    unevaluatedProperties: false
+
+    properties:
+      pins:
+        description:
+          List of gpio pins affected by the properties specified in this
+          subnode.
+        items:
+          oneOf:
+            - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-3][0-9]|14[0-6])$"
+            - enum: [ sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd,
+                      sdc2_data ]
+        minItems: 1
+        maxItems: 36
+
+      function:
+        description:
+          Specify the alternative function to be configured for the specified
+          pins.
+        enum: [ adsp_ext, audio_ref, blsp_i2c1, blsp_i2c2, blsp_i2c3,
+                blsp_i2c4, blsp_i2c5, blsp_i2c6, blsp_i2c7, blsp_i2c8,
+                blsp_i2c9, blsp_i2c10, blsp_i2c11, blsp_i2c12,
+                blsp_spi1, blsp_spi1_cs1, blsp_spi1_cs2, blsp_spi1_cs3,
+                blsp_spi2, blsp_spi3, blsp_spi3_cs1, blsp_spi3_cs2,
+                blsp_spi3_cs3, blsp_spi4, blsp_spi5, blsp_spi6,
+                blsp_spi7, blsp_spi8, blsp_spi9, blsp_spi10,
+                blsp_spi10_cs1, blsp_spi10_cs2, blsp_spi10_cs3,
+                blsp_spi11, blsp_spi12, blsp_uart1, blsp_uart2,
+                blsp_uart3, blsp_uart4, blsp_uart5, blsp_uart6,
+                blsp_uart7, blsp_uart8, blsp_uart9, blsp_uart10,
+                blsp_uart11, blsp_uart12, blsp_uim1, blsp_uim2,
+                blsp_uim3, blsp_uim4, blsp_uim5, blsp_uim6, blsp_uim7,
+                blsp_uim8, blsp_uim9, blsp_uim10, blsp_uim11,
+                blsp_uim12, cam_mclk0, cam_mclk1, cam_mclk2, cam_mclk3,
+                cci_async, cci_async_in0, cci_i2c0, cci_i2c1,
+                cci_timer0, cci_timer1, cci_timer2, cci_timer3,
+                cci_timer4, edp_hpd, gcc_gp1, gcc_gp2, gcc_gp3,
+                gcc_obt, gcc_vtt, gp_mn, gp_pdm0, gp_pdm1, gp_pdm2,
+                gp0_clk, gp1_clk, gpio, hdmi_cec, hdmi_ddc, hdmi_dtest,
+                hdmi_hpd, hdmi_rcv, hsic, ldo_en, ldo_update,
+                mdp_vsync, pci_e0, pci_e0_n, pci_e0_rst, pci_e1,
+                pci_e1_rst, pci_e1_rst_n, pci_e1_clkreq_n, pri_mi2s,
+                qua_mi2s, sata_act, sata_devsleep, sata_devsleep_n,
+                sd_write, sdc_emmc_mode, sdc3, sdc4, sec_mi2s, slimbus,
+                spdif_tx, spkr_i2s, spkr_i2s_ws, spss_geni, ter_mi2s,
+                tsif1, tsif2, uim, uim_batt_alarm ]
+
+    required:
+      - pins
+
+required:
+  - compatible
+  - reg
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    tlmm: pinctrl@fd510000 {
+        compatible = "qcom,apq8084-pinctrl";
+        reg = <0xfd510000 0x4000>;
+
+        gpio-controller;
+        #gpio-cells = <2>;
+        gpio-ranges = <&tlmm 0 0 147>;
+        interrupt-controller;
+        #interrupt-cells = <2>;
+        interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+
+        uart-state {
+            rx-pins {
+                pins = "gpio5";
+                function = "blsp_uart2";
+                bias-pull-up;
+            };
+
+            tx-pins {
+                pins = "gpio4";
+                function = "blsp_uart2";
+                bias-disable;
+            };
+        };
+    };
-- 
2.45.2

Re: [PATCH 0/4] dt-bindings: pinctrl: convert remaining qcom bindings to yaml

[Bjorn Andersson]

On Tue, Jul 09, 2024 at 05:17:52PM GMT, Rayyan Ansari wrote:
> Hi,
> The following patches convert all remaining old text bindings for
> Qualcomm pinctrl to yaml, so device trees can be validated against the
> schema.
> 

Thanks for fixing these up!

I think it would have been good to use andersson@kernel.org as the
maintainer address, but I see the other bindings have the broken address
as well, so I can follow up with a patch to change them all.

Reviewed-by: Bjorn Andersson <andersson@kernel.org>

Regards,
Bjorn

> Thanks,
> Rayyan
> 
> Rayyan Ansari (4):
>   dt-bindings: pinctrl: qcom,apq8064-pinctrl: convert to dtschema
>   dt-bindings: pinctrl: qcom,ipq8064-pinctrl: convert to dtschema
>   dt-bindings: pinctrl: qcom,ipq4019-pinctrl: convert to dtschema
>   dt-bindings: pinctrl: qcom,apq8084-pinctrl: convert to dtschema
> 
>  .../bindings/pinctrl/qcom,apq8064-pinctrl.txt |  95 ---------
>  .../pinctrl/qcom,apq8064-pinctrl.yaml         | 110 ++++++++++
>  .../bindings/pinctrl/qcom,apq8084-pinctrl.txt | 188 ------------------
>  .../pinctrl/qcom,apq8084-pinctrl.yaml         | 129 ++++++++++++
>  .../bindings/pinctrl/qcom,ipq4019-pinctrl.txt |  85 --------
>  .../pinctrl/qcom,ipq4019-pinctrl.yaml         | 102 ++++++++++
>  .../bindings/pinctrl/qcom,ipq8064-pinctrl.txt | 101 ----------
>  .../pinctrl/qcom,ipq8064-pinctrl.yaml         | 108 ++++++++++
>  8 files changed, 449 insertions(+), 469 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.yaml
>  delete mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.yaml
>  delete mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.txt
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.yaml
>  delete mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.yaml
> 
> -- 
> 2.45.2
> 

Re: [PATCH 1/4] dt-bindings: pinctrl: qcom,apq8064-pinctrl: convert to dtschema

[Krzysztof Kozlowski]

On 09/07/2024 18:17, Rayyan Ansari wrote:
> Convert the Qualcomm APQ8064 TLMM block bindings from text to yaml dt
> schema format.
> 
> Signed-off-by: Rayyan Ansari <rayyan.ansari@linaro.org>

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

Re: [PATCH 2/4] dt-bindings: pinctrl: qcom,ipq8064-pinctrl: convert to dtschema

[Krzysztof Kozlowski]

On 09/07/2024 18:17, Rayyan Ansari wrote:
> Convert the Qualcomm IPQ8064 TLMM block bindings from text to yaml dt
> schema format.
> 
> Signed-off-by: Rayyan Ansari <rayyan.ansari@linaro.org>
> ---

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

Re: [PATCH 3/4] dt-bindings: pinctrl: qcom,ipq4019-pinctrl: convert to dtschema

[Krzysztof Kozlowski]

On 09/07/2024 18:17, Rayyan Ansari wrote:
> Convert the Qualcomm IPQ4019 TLMM block bindings from text to yaml dt
> schema format.
> 
> Signed-off-by: Rayyan Ansari <rayyan.ansari@linaro.org>

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

Re: [PATCH 4/4] dt-bindings: pinctrl: qcom,apq8084-pinctrl: convert to dtschema

[Krzysztof Kozlowski]

On 09/07/2024 18:17, Rayyan Ansari wrote:
> Convert the Qualcomm APQ8084 TLMM block bindings from text to yaml dt
> schema format.
> 
> Signed-off-by: Rayyan Ansari <rayyan.ansari@linaro.org>
> ---

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

Re: [PATCH 0/4] dt-bindings: pinctrl: convert remaining qcom bindings to yaml

[Linus Walleij]

On Tue, Jul 9, 2024 at 6:20 PM Rayyan Ansari <rayyan.ansari@linaro.org> wrote:

> Hi,
> The following patches convert all remaining old text bindings for
> Qualcomm pinctrl to yaml, so device trees can be validated against the
> schema.

Patches applied!

Yours,
Linus Walleij