From: Amit Kucheria <amit.kucheria@verdurent.com>
To: Rajeshwari <rkambl@codeaurora.org>
Cc: Andy Gross <agross@kernel.org>, Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Bjorn Andersson <bjorn.andersson@linaro.org>,
linux-arm-msm <linux-arm-msm@vger.kernel.org>,
"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
<devicetree@vger.kernel.org>, LKML <linux-kernel@vger.kernel.org>,
sivaa@codeaurora.org, sanm@codeaurora.org,
Doug Anderson <dianders@chromium.org>
Subject: Re: [PATCH] arm64: dts: qcom: sc7180: Changed polling-delay in Thermal-zones node
Date: Tue, 17 Mar 2020 16:22:00 +0530 [thread overview]
Message-ID: <CAHLCerOSz4aAkukPzRRwOgeiTnw1ATSp0gPd9ujqiv9uAfj2Mg@mail.gmail.com> (raw)
In-Reply-To: <1584430804-8343-1-git-send-email-rkambl@codeaurora.org>
On Tue, Mar 17, 2020 at 1:11 PM Rajeshwari <rkambl@codeaurora.org> wrote:
>
> Changed polling-delay and polling-delay-passive to zero as per
> the requirement.
>
> Signed-off-by: Rajeshwari <rkambl@codeaurora.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
> ---
> arch/arm64/boot/dts/qcom/sc7180.dtsi | 100 +++++++++++++++++------------------
> 1 file changed, 50 insertions(+), 50 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> index ca876ed..d81c4f1 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> @@ -1907,8 +1907,8 @@
>
> thermal-zones {
> cpu0-thermal {
> - polling-delay-passive = <250>;
> - polling-delay = <1000>;
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
>
> thermal-sensors = <&tsens0 1>;
>
> @@ -1955,8 +1955,8 @@
> };
>
> cpu1-thermal {
> - polling-delay-passive = <250>;
> - polling-delay = <1000>;
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
>
> thermal-sensors = <&tsens0 2>;
>
> @@ -2003,8 +2003,8 @@
> };
>
> cpu2-thermal {
> - polling-delay-passive = <250>;
> - polling-delay = <1000>;
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
>
> thermal-sensors = <&tsens0 3>;
>
> @@ -2051,8 +2051,8 @@
> };
>
> cpu3-thermal {
> - polling-delay-passive = <250>;
> - polling-delay = <1000>;
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
>
> thermal-sensors = <&tsens0 4>;
>
> @@ -2099,8 +2099,8 @@
> };
>
> cpu4-thermal {
> - polling-delay-passive = <250>;
> - polling-delay = <1000>;
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
>
> thermal-sensors = <&tsens0 5>;
>
> @@ -2147,8 +2147,8 @@
> };
>
> cpu5-thermal {
> - polling-delay-passive = <250>;
> - polling-delay = <1000>;
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
>
> thermal-sensors = <&tsens0 6>;
>
> @@ -2195,8 +2195,8 @@
> };
>
> cpu6-thermal {
> - polling-delay-passive = <250>;
> - polling-delay = <1000>;
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
>
> thermal-sensors = <&tsens0 9>;
>
> @@ -2235,8 +2235,8 @@
> };
>
> cpu7-thermal {
> - polling-delay-passive = <250>;
> - polling-delay = <1000>;
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
>
> thermal-sensors = <&tsens0 10>;
>
> @@ -2275,8 +2275,8 @@
> };
>
> cpu8-thermal {
> - polling-delay-passive = <250>;
> - polling-delay = <1000>;
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
>
> thermal-sensors = <&tsens0 11>;
>
> @@ -2315,8 +2315,8 @@
> };
>
> cpu9-thermal {
> - polling-delay-passive = <250>;
> - polling-delay = <1000>;
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
>
> thermal-sensors = <&tsens0 12>;
>
> @@ -2355,8 +2355,8 @@
> };
>
> aoss0-thermal {
> - polling-delay-passive = <250>;
> - polling-delay = <1000>;
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
>
> thermal-sensors = <&tsens0 0>;
>
> @@ -2376,8 +2376,8 @@
> };
>
> cpuss0-thermal {
> - polling-delay-passive = <250>;
> - polling-delay = <1000>;
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
>
> thermal-sensors = <&tsens0 7>;
>
> @@ -2396,8 +2396,8 @@
> };
>
> cpuss1-thermal {
> - polling-delay-passive = <250>;
> - polling-delay = <1000>;
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
>
> thermal-sensors = <&tsens0 8>;
>
> @@ -2416,8 +2416,8 @@
> };
>
> gpuss0-thermal {
> - polling-delay-passive = <250>;
> - polling-delay = <1000>;
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
>
> thermal-sensors = <&tsens0 13>;
>
> @@ -2437,8 +2437,8 @@
> };
>
> gpuss1-thermal {
> - polling-delay-passive = <250>;
> - polling-delay = <1000>;
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
>
> thermal-sensors = <&tsens0 14>;
>
> @@ -2458,8 +2458,8 @@
> };
>
> aoss1-thermal {
> - polling-delay-passive = <250>;
> - polling-delay = <1000>;
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
>
> thermal-sensors = <&tsens1 0>;
>
> @@ -2479,8 +2479,8 @@
> };
>
> cwlan-thermal {
> - polling-delay-passive = <250>;
> - polling-delay = <1000>;
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
>
> thermal-sensors = <&tsens1 1>;
>
> @@ -2500,8 +2500,8 @@
> };
>
> audio-thermal {
> - polling-delay-passive = <250>;
> - polling-delay = <1000>;
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
>
> thermal-sensors = <&tsens1 2>;
>
> @@ -2521,8 +2521,8 @@
> };
>
> ddr-thermal {
> - polling-delay-passive = <250>;
> - polling-delay = <1000>;
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
>
> thermal-sensors = <&tsens1 3>;
>
> @@ -2542,8 +2542,8 @@
> };
>
> q6-hvx-thermal {
> - polling-delay-passive = <250>;
> - polling-delay = <1000>;
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
>
> thermal-sensors = <&tsens1 4>;
>
> @@ -2563,8 +2563,8 @@
> };
>
> camera-thermal {
> - polling-delay-passive = <250>;
> - polling-delay = <1000>;
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
>
> thermal-sensors = <&tsens1 5>;
>
> @@ -2584,8 +2584,8 @@
> };
>
> mdm-core-thermal {
> - polling-delay-passive = <250>;
> - polling-delay = <1000>;
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
>
> thermal-sensors = <&tsens1 6>;
>
> @@ -2605,8 +2605,8 @@
> };
>
> mdm-dsp-thermal {
> - polling-delay-passive = <250>;
> - polling-delay = <1000>;
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
>
> thermal-sensors = <&tsens1 7>;
>
> @@ -2626,8 +2626,8 @@
> };
>
> npu-thermal {
> - polling-delay-passive = <250>;
> - polling-delay = <1000>;
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
>
> thermal-sensors = <&tsens1 8>;
>
> @@ -2647,8 +2647,8 @@
> };
>
> video-thermal {
> - polling-delay-passive = <250>;
> - polling-delay = <1000>;
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
>
> thermal-sensors = <&tsens1 9>;
>
> --
> QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
> of Code Aurora Forum, hosted by The Linux Foundation
>
next prev parent reply other threads:[~2020-03-17 10:52 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-03-17 7:40 [PATCH] arm64: dts: qcom: sc7180: Changed polling-delay in Thermal-zones node Rajeshwari
2020-03-17 10:52 ` Amit Kucheria [this message]
2020-03-17 16:50 ` Doug Anderson
[not found] ` <fc7f250e-aa85-0835-8bc4-8274235c74d0@codeaurora.org>
2020-03-18 9:10 ` Amit Kucheria
2020-04-03 18:16 ` Matthias Kaehlcke
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=CAHLCerOSz4aAkukPzRRwOgeiTnw1ATSp0gPd9ujqiv9uAfj2Mg@mail.gmail.com \
--to=amit.kucheria@verdurent.com \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=dianders@chromium.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=rkambl@codeaurora.org \
--cc=robh+dt@kernel.org \
--cc=sanm@codeaurora.org \
--cc=sivaa@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).