devicetree.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Andy Shevchenko <andy.shevchenko@gmail.com>
To: Dmitry Rokosov <ddrokosov@salutedevices.com>
Cc: lee@kernel.org, pavel@ucw.cz, robh+dt@kernel.org,
	 krzysztof.kozlowski+dt@linaro.org, conor+dt@kernel.org,
	kernel@sberdevices.ru,  rockosov@gmail.com,
	devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	 linux-leds@vger.kernel.org
Subject: Re: [PATCH v1 03/11] leds: aw200xx: support HWEN hardware control
Date: Fri, 6 Oct 2023 20:57:23 +0300	[thread overview]
Message-ID: <CAHp75VceobJuEnpQY2Hi1hrjTDCSa-zxi7zxaWt5-k9haGDFUg@mail.gmail.com> (raw)
In-Reply-To: <20231006160437.15627-4-ddrokosov@salutedevices.com>

On Fri, Oct 6, 2023 at 7:04 PM Dmitry Rokosov
<ddrokosov@salutedevices.com> wrote:
>
> HWEN is hardware control, which is used for enable/disable aw200xx chip.
> It's high active, internally pulled down to GND.
>
> After HWEN pin set high the chip begins to load the OTP information,
> which takes 200us to complete. About 200us wait time is needed for
> internal oscillator startup and display SRAM initialization. After
> display SRAM initialization, the registers in page1 to page5 can be

pages 1 to 5


> configured via i2c interface.

...

> +#include <linux/of_gpio.h>

Definitely not.

Use agnostic APIs.

...

> @@ -116,6 +117,7 @@ struct aw200xx {
>         struct mutex mutex;

>         u32 num_leds;
>         u32 display_rows;
> +       int hwen;
>         struct aw200xx_led leds[];

Side note: add a patch to use __counted_by() here.

>  };

...

> +       if (!gpio_is_valid(chip->hwen))

Absolutely not. You may not use legacy GPIO APIs.

> +               return;
> +
> +       gpio_set_value(chip->hwen, 1);

Ditto.

...

> +       usleep_range(400, 500);

fsleep() ?

...

> +static void aw200xx_disable(const struct aw200xx *const chip)
> +{
> +       if (gpio_is_valid(chip->hwen))
> +               gpio_set_value(chip->hwen, 0);
> +}

As per above.

...

> +static void aw200xx_probe_hwen(struct device *dev, struct aw200xx *chip)
> +{
> +       chip->hwen = of_get_named_gpio(dev->of_node, "awinic,hwen-gpio", 0);
> +       if (gpio_is_valid(chip->hwen))
> +               if (devm_gpio_request_one(dev, chip->hwen, GPIOF_OUT_INIT_HIGH,
> +                                         "AW200XX HWEN")) {
> +                       dev_warn(dev, "Can't request gpio %d, tag it invalid\n",
> +                                chip->hwen);
> +                       chip->hwen = -EINVAL;
> +               }
> +}

Please, rewrite this completely using supported APIs and not
deprecated or obsolete ones.

-- 
With Best Regards,
Andy Shevchenko

  reply	other threads:[~2023-10-06 17:58 UTC|newest]

Thread overview: 28+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-10-06 16:04 [PATCH v1 00/11] leds: aw200xx: several driver updates Dmitry Rokosov
2023-10-06 16:04 ` [PATCH v1 01/11] leds: aw200xx: fix write to DIM parameter Dmitry Rokosov
2023-10-06 16:04 ` [PATCH v1 02/11] dt-bindings: leds: aw200xx: fix led dt node pattern Dmitry Rokosov
2023-10-10 14:11   ` Rob Herring
2023-10-06 16:04 ` [PATCH v1 03/11] leds: aw200xx: support HWEN hardware control Dmitry Rokosov
2023-10-06 17:57   ` Andy Shevchenko [this message]
2023-10-09 13:09     ` Dmitry Rokosov
2023-10-06 16:04 ` [PATCH v1 04/11] dt-bindings: leds: aw200xx: introduce optional hwen-gpio property Dmitry Rokosov
2023-10-10 14:13   ` Rob Herring
2023-10-10 14:57     ` Dmitry Rokosov
2023-10-06 16:04 ` [PATCH v1 05/11] leds: aw200xx: calculate dts property display_rows in driver Dmitry Rokosov
2023-10-06 17:59   ` Andy Shevchenko
2023-10-09 13:20     ` Dmitry Rokosov
2023-10-16 23:30       ` George Stark
2023-10-06 16:04 ` [PATCH v1 06/11] dt-bindings: leds: aw200xx: remove property "awinic,display-rows" Dmitry Rokosov
2023-10-10 14:15   ` Rob Herring
2023-10-06 16:04 ` [PATCH v1 07/11] leds: aw200xx: add delay after software reset Dmitry Rokosov
2023-10-06 18:01   ` Andy Shevchenko
2023-10-09 13:14     ` Dmitry Rokosov
2023-10-06 16:04 ` [PATCH v1 08/11] leds: aw200xx: enable disable_locking flag in regmap config Dmitry Rokosov
2023-10-06 16:04 ` [PATCH v1 09/11] leds: aw200xx: improve autodim calculation method Dmitry Rokosov
2023-10-06 18:03   ` Andy Shevchenko
2023-10-09 13:18     ` Dmitry Rokosov
2023-10-09 14:02       ` Dmitry Rokosov
2023-10-16 21:22         ` George Stark
2023-10-06 16:04 ` [PATCH v1 10/11] leds: aw200xx: add support for aw20108 device Dmitry Rokosov
2023-10-06 16:04 ` [PATCH v1 11/11] dt-bindings: leds: Add binding for AW20108 led driver Dmitry Rokosov
2023-10-10 14:17   ` Rob Herring

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=CAHp75VceobJuEnpQY2Hi1hrjTDCSa-zxi7zxaWt5-k9haGDFUg@mail.gmail.com \
    --to=andy.shevchenko@gmail.com \
    --cc=conor+dt@kernel.org \
    --cc=ddrokosov@salutedevices.com \
    --cc=devicetree@vger.kernel.org \
    --cc=kernel@sberdevices.ru \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=lee@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-leds@vger.kernel.org \
    --cc=pavel@ucw.cz \
    --cc=robh+dt@kernel.org \
    --cc=rockosov@gmail.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).