* [PATCH v5 0/2] clk: uniphier: add clock drivers for UniPhier SoCs
@ 2016-07-26 18:09 Masahiro Yamada
2016-07-26 18:09 ` [PATCH v5 2/2] clk: uniphier: add clock data " Masahiro Yamada
2016-07-28 2:25 ` [PATCH v5 0/2] clk: uniphier: add clock drivers " Masahiro Yamada
0 siblings, 2 replies; 5+ messages in thread
From: Masahiro Yamada @ 2016-07-26 18:09 UTC (permalink / raw)
To: linux-clk
Cc: Mark Rutland, devicetree, Michael Turquette, Stephen Boyd,
linux-kernel, Masahiro Yamada, Rob Herring, linux-arm-kernel
I split into two patches to make review easier.
1/2: core support code
2/2: data arrays
Changes in v5:
- Rebase onto next-20160726 for easier git-am
Changes in v4:
- Unify module_platform_driver() boilerplate into a single place
- Add binding document
- Add USB3 clocks
Changes in v3:
- Change to platform drivers instead of OF_CLK_DECLARE
- Split into a core part + SoC drivers
SoC drivers just consist of tables of SoC-specific data.
This allows reviewer to concentrate on the core-part
- Hard-code parent clock names for cascading
Changes in v2:
- split emmc_hw_reset
- make SD clock rate-controllable
- add CLK_SET_RATE_PARENT flag to mux, gate, fixed-factor clocks
Masahiro Yamada (2):
clk: uniphier: add core support code for UniPhier clock drivers
clk: uniphier: add clock data for UniPhier SoCs
.../devicetree/bindings/clock/uniphier-clock.txt | 123 ++++
MAINTAINERS | 1 +
drivers/clk/Kconfig | 1 +
drivers/clk/Makefile | 1 +
drivers/clk/uniphier/Kconfig | 9 +
drivers/clk/uniphier/Makefile | 9 +
drivers/clk/uniphier/clk-uniphier-core.c | 216 +++++++
drivers/clk/uniphier/clk-uniphier-fixed-factor.c | 49 ++
drivers/clk/uniphier/clk-uniphier-fixed-rate.c | 48 ++
drivers/clk/uniphier/clk-uniphier-gate.c | 97 ++++
drivers/clk/uniphier/clk-uniphier-mio.c | 195 +++++++
drivers/clk/uniphier/clk-uniphier-mux.c | 95 ++++
drivers/clk/uniphier/clk-uniphier-peri.c | 95 ++++
drivers/clk/uniphier/clk-uniphier-sys.c | 626 +++++++++++++++++++++
drivers/clk/uniphier/clk-uniphier.h | 96 ++++
15 files changed, 1661 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/uniphier-clock.txt
create mode 100644 drivers/clk/uniphier/Kconfig
create mode 100644 drivers/clk/uniphier/Makefile
create mode 100644 drivers/clk/uniphier/clk-uniphier-core.c
create mode 100644 drivers/clk/uniphier/clk-uniphier-fixed-factor.c
create mode 100644 drivers/clk/uniphier/clk-uniphier-fixed-rate.c
create mode 100644 drivers/clk/uniphier/clk-uniphier-gate.c
create mode 100644 drivers/clk/uniphier/clk-uniphier-mio.c
create mode 100644 drivers/clk/uniphier/clk-uniphier-mux.c
create mode 100644 drivers/clk/uniphier/clk-uniphier-peri.c
create mode 100644 drivers/clk/uniphier/clk-uniphier-sys.c
create mode 100644 drivers/clk/uniphier/clk-uniphier.h
--
1.9.1
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH v5 2/2] clk: uniphier: add clock data for UniPhier SoCs
2016-07-26 18:09 [PATCH v5 0/2] clk: uniphier: add clock drivers for UniPhier SoCs Masahiro Yamada
@ 2016-07-26 18:09 ` Masahiro Yamada
2016-07-29 20:13 ` Rob Herring
2016-07-28 2:25 ` [PATCH v5 0/2] clk: uniphier: add clock drivers " Masahiro Yamada
1 sibling, 1 reply; 5+ messages in thread
From: Masahiro Yamada @ 2016-07-26 18:09 UTC (permalink / raw)
To: linux-clk
Cc: Mark Rutland, devicetree, Michael Turquette, Stephen Boyd,
linux-kernel, Masahiro Yamada, Rob Herring, linux-arm-kernel
Add clock data arrays for all UniPhier SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
---
.../devicetree/bindings/clock/uniphier-clock.txt | 123 ++++
drivers/clk/uniphier/Makefile | 3 +
drivers/clk/uniphier/clk-uniphier-core.c | 91 +++
drivers/clk/uniphier/clk-uniphier-mio.c | 195 +++++++
drivers/clk/uniphier/clk-uniphier-peri.c | 95 ++++
drivers/clk/uniphier/clk-uniphier-sys.c | 626 +++++++++++++++++++++
drivers/clk/uniphier/clk-uniphier.h | 13 +
7 files changed, 1146 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/uniphier-clock.txt
create mode 100644 drivers/clk/uniphier/clk-uniphier-mio.c
create mode 100644 drivers/clk/uniphier/clk-uniphier-peri.c
create mode 100644 drivers/clk/uniphier/clk-uniphier-sys.c
diff --git a/Documentation/devicetree/bindings/clock/uniphier-clock.txt b/Documentation/devicetree/bindings/clock/uniphier-clock.txt
new file mode 100644
index 0000000..1a4fee1
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/uniphier-clock.txt
@@ -0,0 +1,123 @@
+UniPhier clock controller
+
+
+System clock
+------------
+
+Required properties:
+- compatible: should be one of the following:
+ "socionext,uniphier-sld3-clock" - for PH1-sLD3 SoC.
+ "socionext,uniphier-ld4-clock" - for PH1-LD4 SoC.
+ "socionext,uniphier-pro4-clock" - for PH1-Pro4 SoC.
+ "socionext,uniphier-sld8-clock" - for PH1-sLD8 SoC.
+ "socionext,uniphier-pro5-clock" - for PH1-Pro5 SoC.
+ "socionext,uniphier-pxs2-clock" - for ProXstream2/PH1-LD6b SoC.
+ "socionext,uniphier-ld11-clock" - for PH1-LD11 SoC.
+ "socionext,uniphier-ld20-clock" - for PH1-LD20 SoC.
+- #clock-cells: should be 1.
+
+Note:
+The clock node should be a child of a syscon node.
+
+Example:
+
+ sysctrl@61840000 {
+ compatible = "simple-mfd", "syscon";
+ reg = <0x61840000 0x4000>;
+
+ clock {
+ compatible = "socionext,uniphier-ld20-clock";
+ #clock-cells = <1>;
+ };
+
+ other nodes ...
+ };
+
+
+Media I/O (MIO) clock
+---------------------
+
+Required properties:
+- compatible: should be one of the following:
+ "socionext,uniphier-sld3-mio-clock" - for PH1-sLD3 SoC.
+ "socionext,uniphier-ld4-mio-clock" - for PH1-LD4 SoC.
+ "socionext,uniphier-pro4-mio-clock" - for PH1-Pro4 SoC.
+ "socionext,uniphier-sld8-mio-clock" - for PH1-sLD8 SoC.
+ "socionext,uniphier-pro5-mio-clock" - for PH1-Pro5 SoC.
+ "socionext,uniphier-pxs2-mio-clock" - for ProXstream2/PH1-LD6b SoC.
+ "socionext,uniphier-ld11-mio-clock" - for PH1-LD11 SoC.
+ "socionext,uniphier-ld20-mio-clock" - for PH1-LD20 SoC.
+- #clock-cells: should be 1.
+
+Note:
+The clock node should be a child of a syscon node.
+
+Example:
+
+ mioctrl@59810000 {
+ compatible = "simple-mfd", "syscon";
+ reg = <0x59810000 0x800>;
+
+ clock {
+ compatible = "socionext,uniphier-ld20-mio-clock";
+ #clock-cells = <1>;
+ };
+
+ other nodes ...
+ };
+
+Provided clocks:
+
+0: SD host ch0
+1: eMMC host
+2: SD host ch1
+3: MIO DMAC
+4: USB2 host ch0
+5: USB2 host ch1
+6: USB2 host ch2
+7: USB2 host ch3
+
+
+Peripheral clock
+----------------
+
+Required properties:
+- compatible: should be one of the following:
+ "socionext,uniphier-sld3-peri-clock" - for PH1-sLD3 SoC.
+ "socionext,uniphier-ld4-peri-clock" - for PH1-LD4 SoC.
+ "socionext,uniphier-pro4-peri-clock" - for PH1-Pro4 SoC.
+ "socionext,uniphier-sld8-peri-clock" - for PH1-sLD8 SoC.
+ "socionext,uniphier-pro5-peri-clock" - for PH1-Pro5 SoC.
+ "socionext,uniphier-pxs2-peri-clock" - for ProXstream2/PH1-LD6b SoC.
+ "socionext,uniphier-ld11-peri-clock" - for PH1-LD11 SoC.
+ "socionext,uniphier-ld20-peri-clock" - for PH1-LD20 SoC.
+- #clock-cells: should be 1.
+
+Note:
+The clock node should be a child of a syscon node.
+
+Example:
+
+ perictrl@59820000 {
+ compatible = "simple-mfd", "syscon";
+ reg = <0x59820000 0x200>;
+
+ clock {
+ compatible = "socionext,uniphier-ld20-peri-clock";
+ #clock-cells = <1>;
+ };
+
+ other nodes ...
+ };
+
+ 0: UART ch0
+ 1: UART ch1
+ 2: UART ch2
+ 3: UART ch3
+ 4: I2C ch0
+ 5: I2C ch1
+ 6: I2C ch2
+ 7: I2C ch3
+ 8: I2C ch4
+ 9: I2C ch5
+10: I2C ch6
diff --git a/drivers/clk/uniphier/Makefile b/drivers/clk/uniphier/Makefile
index 8f359aa..6822691 100644
--- a/drivers/clk/uniphier/Makefile
+++ b/drivers/clk/uniphier/Makefile
@@ -4,3 +4,6 @@ clk-uniphier-y += clk-uniphier-fixed-factor.o
clk-uniphier-y += clk-uniphier-fixed-rate.o
clk-uniphier-y += clk-uniphier-gate.o
clk-uniphier-y += clk-uniphier-mux.o
+clk-uniphier-y += clk-uniphier-sys.o
+clk-uniphier-y += clk-uniphier-mio.o
+clk-uniphier-y += clk-uniphier-peri.o
diff --git a/drivers/clk/uniphier/clk-uniphier-core.c b/drivers/clk/uniphier/clk-uniphier-core.c
index fcb7582..57e6762 100644
--- a/drivers/clk/uniphier/clk-uniphier-core.c
+++ b/drivers/clk/uniphier/clk-uniphier-core.c
@@ -45,6 +45,97 @@ static struct clk_hw *uniphier_clk_register(struct device *dev,
}
static const struct of_device_id uniphier_clk_match[] = {
+ /* System clock */
+ {
+ .compatible = "socionext,uniphier-ld4-clock",
+ .data = uniphier_ld4_sys_clk_data,
+ },
+ {
+ .compatible = "socionext,uniphier-pro4-clock",
+ .data = uniphier_pro4_sys_clk_data,
+ },
+ {
+ .compatible = "socionext,uniphier-sld8-clock",
+ .data = uniphier_sld8_sys_clk_data,
+ },
+ {
+ .compatible = "socionext,uniphier-pro5-clock",
+ .data = uniphier_pro5_sys_clk_data,
+ },
+ {
+ .compatible = "socionext,uniphier-pxs2-clock",
+ .data = uniphier_pxs2_sys_clk_data,
+ },
+ {
+ .compatible = "socionext,uniphier-ld11-clock",
+ .data = uniphier_ld11_sys_clk_data,
+ },
+ {
+ .compatible = "socionext,uniphier-ld20-clock",
+ .data = uniphier_ld20_sys_clk_data,
+ },
+ /* Media I/O clock */
+ {
+ .compatible = "socionext,uniphier-sld3-mio-clock",
+ .data = uniphier_sld3_mio_clk_data,
+ },
+ {
+ .compatible = "socionext,uniphier-ld4-mio-clock",
+ .data = uniphier_sld3_mio_clk_data,
+ },
+ {
+ .compatible = "socionext,uniphier-pro4-mio-clock",
+ .data = uniphier_sld3_mio_clk_data,
+ },
+ {
+ .compatible = "socionext,uniphier-sld8-mio-clock",
+ .data = uniphier_sld3_mio_clk_data,
+ },
+ {
+ .compatible = "socionext,uniphier-pro5-mio-clock",
+ .data = uniphier_pro5_mio_clk_data,
+ },
+ {
+ .compatible = "socionext,uniphier-pxs2-mio-clock",
+ .data = uniphier_pro5_mio_clk_data,
+ },
+ {
+ .compatible = "socionext,uniphier-ld11-mio-clock",
+ .data = uniphier_sld3_mio_clk_data,
+ },
+ {
+ .compatible = "socionext,uniphier-ld20-mio-clock",
+ .data = uniphier_pro5_mio_clk_data,
+ },
+ /* Peripheral clock */
+ {
+ .compatible = "socionext,uniphier-ld4-peri-clock",
+ .data = uniphier_ld4_peri_clk_data,
+ },
+ {
+ .compatible = "socionext,uniphier-pro4-peri-clock",
+ .data = uniphier_pro4_peri_clk_data,
+ },
+ {
+ .compatible = "socionext,uniphier-sld8-peri-clock",
+ .data = uniphier_ld4_peri_clk_data,
+ },
+ {
+ .compatible = "socionext,uniphier-pro5-peri-clock",
+ .data = uniphier_pro4_peri_clk_data,
+ },
+ {
+ .compatible = "socionext,uniphier-pxs2-peri-clock",
+ .data = uniphier_pro4_peri_clk_data,
+ },
+ {
+ .compatible = "socionext,uniphier-ld11-peri-clock",
+ .data = uniphier_pro4_peri_clk_data,
+ },
+ {
+ .compatible = "socionext,uniphier-ld20-peri-clock",
+ .data = uniphier_pro4_peri_clk_data,
+ },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, uniphier_clk_match);
diff --git a/drivers/clk/uniphier/clk-uniphier-mio.c b/drivers/clk/uniphier/clk-uniphier-mio.c
new file mode 100644
index 0000000..711bab5
--- /dev/null
+++ b/drivers/clk/uniphier/clk-uniphier-mio.c
@@ -0,0 +1,195 @@
+/*
+ * Copyright (C) 2016 Socionext Inc.
+ * Author: Masahiro Yamada <yamada.masahiro@socionext.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/bitops.h>
+
+#include "clk-uniphier.h"
+
+#define UNIPHIER_MIO_CLK_SD_FIXED \
+ { \
+ .name = "sd-44m", \
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR, \
+ .output_index = -1, \
+ .data.factor = { \
+ .parent_name = "sd-133m", \
+ .mult = 1, \
+ .div = 3, \
+ }, \
+ }, \
+ { \
+ .name = "sd-33m", \
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR, \
+ .output_index = -1, \
+ .data.factor = { \
+ .parent_name = "sd-200m", \
+ .mult = 1, \
+ .div = 6, \
+ }, \
+ }, \
+ { \
+ .name = "sd-50m", \
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR, \
+ .output_index = -1, \
+ .data.factor = { \
+ .parent_name = "sd-200m", \
+ .mult = 1, \
+ .div = 4, \
+ }, \
+ }, \
+ { \
+ .name = "sd-67m", \
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR, \
+ .output_index = -1, \
+ .data.factor = { \
+ .parent_name = "sd-200m", \
+ .mult = 1, \
+ .div = 3, \
+ }, \
+ }, \
+ { \
+ .name = "sd-100m", \
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR, \
+ .output_index = -1, \
+ .data.factor = { \
+ .parent_name = "sd-200m", \
+ .mult = 1, \
+ .div = 2, \
+ }, \
+ }, \
+ { \
+ .name = "sd-40m", \
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR, \
+ .output_index = -1, \
+ .data.factor = { \
+ .parent_name = "sd-200m", \
+ .mult = 1, \
+ .div = 5, \
+ }, \
+ }, \
+ { \
+ .name = "sd-25m", \
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR, \
+ .output_index = -1, \
+ .data.factor = { \
+ .parent_name = "sd-200m", \
+ .mult = 1, \
+ .div = 8, \
+ }, \
+ }, \
+ { \
+ .name = "sd-22m", \
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR, \
+ .output_index = -1, \
+ .data.factor = { \
+ .parent_name = "sd-133m", \
+ .mult = 1, \
+ .div = 6, \
+ }, \
+ }
+
+#define UNIPHIER_MIO_CLK_SD(index, ch) \
+ { \
+ .name = "sd" #ch "-sel", \
+ .type = UNIPHIER_CLK_TYPE_MUX, \
+ .output_index = -1, \
+ .data.mux = { \
+ .parent_names = { \
+ "sd-44m", \
+ "sd-33m", \
+ "sd-50m", \
+ "sd-67m", \
+ "sd-100m", \
+ "sd-40m", \
+ "sd-25m", \
+ "sd-22m", \
+ }, \
+ .num_parents = 8, \
+ .reg = 0x30 + 0x200 * ch, \
+ .masks = { \
+ 0x00031000, \
+ 0x00031000, \
+ 0x00031000, \
+ 0x00031000, \
+ 0x00001300, \
+ 0x00001300, \
+ 0x00001300, \
+ 0x00001300, \
+ }, \
+ .vals = { \
+ 0x00000000, \
+ 0x00010000, \
+ 0x00020000, \
+ 0x00030000, \
+ 0x00001000, \
+ 0x00001100, \
+ 0x00001200, \
+ 0x00001300, \
+ }, \
+ }, \
+ }, \
+ { \
+ .name = "sd" #ch, \
+ .type = UNIPHIER_CLK_TYPE_GATE, \
+ .output_index = (index), \
+ .data.gate = { \
+ .parent_name = "sd" #ch "-sel", \
+ .reg = 0x20 + 0x200 * ch, \
+ .mask = BIT(8), \
+ }, \
+ }
+
+#define UNIPHIER_MIO_CLK_USB2(index, ch) \
+ { \
+ .name = "usb2" #ch, \
+ .type = UNIPHIER_CLK_TYPE_GATE, \
+ .output_index = (index), \
+ .data.gate = { \
+ .parent_name = "usb2", \
+ .reg = 0x20 + 0x200 * ch, \
+ .mask = BIT(29) | BIT(28), \
+ }, \
+ }
+
+#define UNIPHIER_MIO_CLK_DMAC(index) \
+ { \
+ .name = "miodmac", \
+ .type = UNIPHIER_CLK_TYPE_GATE, \
+ .output_index = (index), \
+ .data.gate = { \
+ .parent_name = "stdmac", \
+ .reg = 0x20, \
+ .mask = BIT(25), \
+ }, \
+ }
+
+const struct uniphier_clk_data uniphier_sld3_mio_clk_data[] = {
+ UNIPHIER_MIO_CLK_SD_FIXED,
+ UNIPHIER_MIO_CLK_SD(0, 0),
+ UNIPHIER_MIO_CLK_SD(1, 1),
+ UNIPHIER_MIO_CLK_SD(2, 2),
+ UNIPHIER_MIO_CLK_DMAC(3),
+ UNIPHIER_MIO_CLK_USB2(4, 0),
+ UNIPHIER_MIO_CLK_USB2(5, 1),
+ UNIPHIER_MIO_CLK_USB2(6, 2),
+ UNIPHIER_MIO_CLK_USB2(7, 3),
+ { /* sentinel */ }
+};
+
+const struct uniphier_clk_data uniphier_pro5_mio_clk_data[] = {
+ UNIPHIER_MIO_CLK_SD_FIXED,
+ UNIPHIER_MIO_CLK_SD(0, 0),
+ UNIPHIER_MIO_CLK_SD(1, 1),
+ { /* sentinel */ }
+};
diff --git a/drivers/clk/uniphier/clk-uniphier-peri.c b/drivers/clk/uniphier/clk-uniphier-peri.c
new file mode 100644
index 0000000..029c65f
--- /dev/null
+++ b/drivers/clk/uniphier/clk-uniphier-peri.c
@@ -0,0 +1,95 @@
+/*
+ * Copyright (C) 2016 Socionext Inc.
+ * Author: Masahiro Yamada <yamada.masahiro@socionext.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/bitops.h>
+
+#include "clk-uniphier.h"
+
+#define UNIPHIER_PERI_CLK_UART(index, ch) \
+ { \
+ .name = "uart" #ch, \
+ .type = UNIPHIER_CLK_TYPE_GATE, \
+ .output_index = (index), \
+ .data.gate = { \
+ .parent_name = "uart", \
+ .reg = 0x24, \
+ .mask = BIT(19 + (ch)), \
+ }, \
+ }
+
+#define UNIPHIER_PERI_CLK_I2C_COMMON \
+ { \
+ .name = "i2c-common", \
+ .type = UNIPHIER_CLK_TYPE_GATE, \
+ .output_index = -1, \
+ .data.gate = { \
+ .parent_name = "i2c", \
+ .reg = 0x20, \
+ .mask = BIT(1), \
+ }, \
+ }
+
+#define UNIPHIER_PERI_CLK_I2C(index, ch) \
+ { \
+ .name = "i2c" #ch, \
+ .type = UNIPHIER_CLK_TYPE_GATE, \
+ .output_index = (index), \
+ .data.gate = { \
+ .parent_name = "i2c-common", \
+ .reg = 0x24, \
+ .mask = BIT(5 + (ch)), \
+ }, \
+ }
+
+#define UNIPHIER_PERI_CLK_FI2C(index, ch) \
+ { \
+ .name = "i2c" #ch, \
+ .type = UNIPHIER_CLK_TYPE_GATE, \
+ .output_index = (index), \
+ .data.gate = { \
+ .parent_name = "i2c", \
+ .reg = 0x24, \
+ .mask = BIT(24 + (ch)), \
+ }, \
+ }
+
+const struct uniphier_clk_data uniphier_ld4_peri_clk_data[] = {
+ UNIPHIER_PERI_CLK_UART(0, 0),
+ UNIPHIER_PERI_CLK_UART(1, 1),
+ UNIPHIER_PERI_CLK_UART(2, 2),
+ UNIPHIER_PERI_CLK_UART(3, 3),
+ UNIPHIER_PERI_CLK_I2C_COMMON,
+ UNIPHIER_PERI_CLK_I2C(4, 0),
+ UNIPHIER_PERI_CLK_I2C(5, 1),
+ UNIPHIER_PERI_CLK_I2C(6, 2),
+ UNIPHIER_PERI_CLK_I2C(7, 3),
+ UNIPHIER_PERI_CLK_I2C(8, 4),
+ { /* sentinel */ }
+};
+
+const struct uniphier_clk_data uniphier_pro4_peri_clk_data[] = {
+ UNIPHIER_PERI_CLK_UART(0, 0),
+ UNIPHIER_PERI_CLK_UART(1, 1),
+ UNIPHIER_PERI_CLK_UART(2, 2),
+ UNIPHIER_PERI_CLK_UART(3, 3),
+ UNIPHIER_PERI_CLK_FI2C(4, 0),
+ UNIPHIER_PERI_CLK_FI2C(5, 1),
+ UNIPHIER_PERI_CLK_FI2C(6, 2),
+ UNIPHIER_PERI_CLK_FI2C(7, 3),
+ UNIPHIER_PERI_CLK_FI2C(8, 4),
+ UNIPHIER_PERI_CLK_FI2C(9, 5),
+ UNIPHIER_PERI_CLK_FI2C(10, 6),
+ { /* sentinel */ }
+};
diff --git a/drivers/clk/uniphier/clk-uniphier-sys.c b/drivers/clk/uniphier/clk-uniphier-sys.c
new file mode 100644
index 0000000..2e1e4cc
--- /dev/null
+++ b/drivers/clk/uniphier/clk-uniphier-sys.c
@@ -0,0 +1,626 @@
+/*
+ * Copyright (C) 2016 Socionext Inc.
+ * Author: Masahiro Yamada <yamada.masahiro@socionext.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/bitops.h>
+
+#include "clk-uniphier.h"
+
+#define UNIPHIER_SLD3_SYS_CLK_SD \
+ { \
+ .name = "sd-200m", \
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR, \
+ .output_index = -1, \
+ .data.factor = { \
+ .parent_name = "spll", \
+ .mult = 1, \
+ .div = 8, \
+ }, \
+ }, \
+ { \
+ .name = "sd-133m", \
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR, \
+ .output_index = -1, \
+ .data.factor = { \
+ .parent_name = "vpll27a", \
+ .mult = 1, \
+ .div = 2, \
+ }, \
+ }
+
+#define UNIPHIER_PRO5_SYS_CLK_SD \
+ { \
+ .name = "sd-200m", \
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR, \
+ .output_index = -1, \
+ .data.factor = { \
+ .parent_name = "spll", \
+ .mult = 1, \
+ .div = 12, \
+ }, \
+ }, \
+ { \
+ .name = "sd-133m", \
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR, \
+ .output_index = -1, \
+ .data.factor = { \
+ .parent_name = "spll", \
+ .mult = 1, \
+ .div = 18, \
+ }, \
+ }
+
+#define UNIPHIER_LD20_SYS_CLK_SD \
+ { \
+ .name = "sd-200m", \
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR, \
+ .output_index = -1, \
+ .data.factor = { \
+ .parent_name = "spll", \
+ .mult = 1, \
+ .div = 10, \
+ }, \
+ }, \
+ { \
+ .name = "sd-133m", \
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR, \
+ .output_index = -1, \
+ .data.factor = { \
+ .parent_name = "spll", \
+ .mult = 1, \
+ .div = 15, \
+ }, \
+ }
+
+#define UNIPHIER_PRO5_SYS_CLK_I2C \
+ { \
+ .name = "i2c", \
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR, \
+ .output_index = -1, \
+ .data.factor = { \
+ .parent_name = "spll", \
+ .mult = 1, \
+ .div = 48, \
+ }, \
+ }
+
+#define UNIPHIER_LD11_SYS_CLK_I2C \
+ { \
+ .name = "i2c", \
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR, \
+ .output_index = -1, \
+ .data.factor = { \
+ .parent_name = "spll", \
+ .mult = 1, \
+ .div = 40, \
+ }, \
+ }
+
+#define UNIPHIER_SLD3_SYS_CLK_STDMAC(index) \
+ { \
+ .name = "stdmac", \
+ .type = UNIPHIER_CLK_TYPE_GATE, \
+ .output_index = (index), \
+ .data.gate = { \
+ .parent_name = NULL, \
+ .reg = 0x2104, \
+ .mask = BIT(10), \
+ }, \
+ }
+
+#define UNIPHIER_LD11_SYS_CLK_STDMAC(index) \
+ { \
+ .name = "stdmac", \
+ .type = UNIPHIER_CLK_TYPE_GATE, \
+ .output_index = (index), \
+ .data.gate = { \
+ .parent_name = NULL, \
+ .reg = 0x210c, \
+ .mask = BIT(8), \
+ }, \
+ }
+
+#define UNIPHIER_PRO4_SYS_CLK_GIO(index) \
+ { \
+ .name = "gio", \
+ .type = UNIPHIER_CLK_TYPE_GATE, \
+ .output_index = (index), \
+ .data.gate = { \
+ .parent_name = NULL, \
+ .reg = 0x2104, \
+ .mask = BIT(6), \
+ }, \
+ }
+
+#define UNIPHIER_PRO4_SYS_CLK_USB3(index, ch) \
+ { \
+ .name = "usb3" #ch, \
+ .type = UNIPHIER_CLK_TYPE_GATE, \
+ .output_index = (index), \
+ .data.gate = { \
+ .parent_name = NULL, \
+ .reg = 0x2104, \
+ .mask = BIT(16 + (ch)), \
+ }, \
+ }
+
+#define UNIPHIER_PXS2_SYS_CLK_USB3PHY(index, ch) \
+ { \
+ .name = "usb3" #ch "phy", \
+ .type = UNIPHIER_CLK_TYPE_GATE, \
+ .output_index = (index), \
+ .data.gate = { \
+ .parent_name = NULL, \
+ .reg = 0x2104, \
+ .mask = BIT(19 + (ch)), \
+ }, \
+ }
+
+const struct uniphier_clk_data uniphier_sld3_sys_clk_data[] = {
+ {
+ .name = "spll", /* 1597.44 MHz */
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "ref",
+ .mult = 65,
+ .div = 1,
+ },
+ },
+ {
+ .name = "upll", /* 288 MHz */
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "ref",
+ .mult = 288000,
+ .div = 24576,
+ },
+ },
+ {
+ .name = "a2pll", /* 589.824 MHz */
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "ref",
+ .mult = 24,
+ .div = 1,
+ },
+ },
+ {
+ .name = "vpll27a", /* 270 MHz */
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "ref",
+ .mult = 270000,
+ .div = 24576,
+ },
+ },
+ {
+ .name = "uart",
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = 0,
+ .data.factor = {
+ .parent_name = "a2pll",
+ .mult = 1,
+ .div = 16,
+ },
+ },
+ {
+ .name = "i2c",
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = 1,
+ .data.factor = {
+ .parent_name = "spll",
+ .mult = 1,
+ .div = 16,
+ },
+ },
+ UNIPHIER_SLD3_SYS_CLK_SD,
+ {
+ .name = "usb2",
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "upll",
+ .mult = 1,
+ .div = 12,
+ },
+ },
+ UNIPHIER_SLD3_SYS_CLK_STDMAC(8),
+ { /* sentinel */ }
+};
+
+const struct uniphier_clk_data uniphier_ld4_sys_clk_data[] = {
+ {
+ .name = "spll", /* 1597.44 MHz */
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "ref",
+ .mult = 65,
+ .div = 1,
+ },
+ },
+ {
+ .name = "upll", /* 288 MHz */
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "ref",
+ .mult = 288000,
+ .div = 24576,
+ },
+ },
+ {
+ .name = "a2pll", /* 589.824 MHz */
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "ref",
+ .mult = 24,
+ .div = 1,
+ },
+ },
+ {
+ .name = "vpll27a", /* 270 MHz */
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "ref",
+ .mult = 270000,
+ .div = 24576,
+ },
+ },
+ {
+ .name = "uart",
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "a2pll",
+ .mult = 1,
+ .div = 16,
+ },
+ },
+ {
+ .name = "i2c",
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "spll",
+ .mult = 1,
+ .div = 16,
+ },
+ },
+ UNIPHIER_SLD3_SYS_CLK_SD,
+ {
+ .name = "usb2",
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "upll",
+ .mult = 1,
+ .div = 12,
+ },
+ },
+ UNIPHIER_SLD3_SYS_CLK_STDMAC(8), /* Ether, HSC, MIO */
+ { /* sentinel */ }
+};
+
+const struct uniphier_clk_data uniphier_pro4_sys_clk_data[] = {
+ {
+ .name = "spll", /* 1600 MHz */
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "ref",
+ .mult = 64,
+ .div = 1,
+ },
+ },
+ {
+ .name = "upll", /* 288 MHz */
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "ref",
+ .mult = 288,
+ .div = 25,
+ },
+ },
+ {
+ .name = "a2pll", /* 589.824 MHz */
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "upll",
+ .mult = 256,
+ .div = 125,
+ },
+ },
+ {
+ .name = "vpll27a", /* 270 MHz */
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "ref",
+ .mult = 270,
+ .div = 25,
+ },
+ },
+ {
+ .name = "uart",
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "a2pll",
+ .mult = 1,
+ .div = 8,
+ },
+ },
+ {
+ .name = "i2c",
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "spll",
+ .mult = 1,
+ .div = 32,
+ },
+ },
+ UNIPHIER_SLD3_SYS_CLK_SD,
+ UNIPHIER_SLD3_SYS_CLK_STDMAC(8), /* HSC, MIO, RLE */
+ UNIPHIER_PRO4_SYS_CLK_GIO(12), /* Ether, SATA, USB3 */
+ UNIPHIER_PRO4_SYS_CLK_USB3(16, 0),
+ UNIPHIER_PRO4_SYS_CLK_USB3(17, 1),
+ { /* sentinel */ }
+};
+
+const struct uniphier_clk_data uniphier_sld8_sys_clk_data[] = {
+ {
+ .name = "spll", /* 1600 MHz */
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "ref",
+ .mult = 64,
+ .div = 1,
+ },
+ },
+ {
+ .name = "upll", /* 288 MHz */
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "ref",
+ .mult = 288,
+ .div = 25,
+ },
+ },
+ {
+ .name = "vpll27a", /* 270 MHz */
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "ref",
+ .mult = 270,
+ .div = 25,
+ },
+ },
+ {
+ .name = "uart",
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "spll",
+ .mult = 1,
+ .div = 20,
+ },
+ },
+ {
+ .name = "i2c",
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "spll",
+ .mult = 1,
+ .div = 16,
+ },
+ },
+ UNIPHIER_SLD3_SYS_CLK_SD,
+ {
+ .name = "usb2",
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "upll",
+ .mult = 1,
+ .div = 12,
+ },
+ },
+ UNIPHIER_SLD3_SYS_CLK_STDMAC(8), /* Ether, HSC, MIO */
+ { /* sentinel */ }
+};
+
+const struct uniphier_clk_data uniphier_pro5_sys_clk_data[] = {
+ {
+ .name = "spll", /* 2400 MHz */
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "ref",
+ .mult = 120,
+ .div = 1,
+ },
+ },
+ {
+ .name = "dapll1", /* 2560 MHz */
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "ref",
+ .mult = 128,
+ .div = 1,
+ },
+ },
+ {
+ .name = "dapll2", /* 2949.12 MHz */
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "dapll1",
+ .mult = 144,
+ .div = 125,
+ },
+ },
+ {
+ .name = "uart",
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "dapll2",
+ .mult = 1,
+ .div = 40,
+ },
+ },
+ UNIPHIER_PRO5_SYS_CLK_I2C,
+ UNIPHIER_PRO5_SYS_CLK_SD,
+ UNIPHIER_SLD3_SYS_CLK_STDMAC(8), /* HSC */
+ UNIPHIER_PRO4_SYS_CLK_GIO(12), /* PCIe, USB3 */
+ UNIPHIER_PRO4_SYS_CLK_USB3(16, 0),
+ UNIPHIER_PRO4_SYS_CLK_USB3(17, 1),
+ { /* sentinel */ }
+};
+
+const struct uniphier_clk_data uniphier_pxs2_sys_clk_data[] = {
+ {
+ .name = "spll", /* 2400 MHz */
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "ref",
+ .mult = 96,
+ .div = 1,
+ },
+ },
+ {
+ .name = "uart",
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "spll",
+ .mult = 1,
+ .div = 27,
+ },
+ },
+ UNIPHIER_PRO5_SYS_CLK_I2C,
+ UNIPHIER_PRO5_SYS_CLK_SD,
+ UNIPHIER_SLD3_SYS_CLK_STDMAC(8), /* HSC, RLE */
+ /* GIO is always clock-enabled: no function for 0x2104 bit6 */
+ UNIPHIER_PRO4_SYS_CLK_USB3(16, 0),
+ UNIPHIER_PRO4_SYS_CLK_USB3(17, 1),
+ /* The document mentions 0x2104 bit 18, but not functional */
+ UNIPHIER_PXS2_SYS_CLK_USB3PHY(18, 0),
+ UNIPHIER_PXS2_SYS_CLK_USB3PHY(19, 1),
+ { /* sentinel */ }
+};
+
+const struct uniphier_clk_data uniphier_ld11_sys_clk_data[] = {
+ {
+ .name = "spll", /* 2000 MHz */
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "ref",
+ .mult = 80,
+ .div = 1,
+ },
+ },
+ {
+ .name = "uart",
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "spll",
+ .mult = 1,
+ .div = 34,
+ },
+ },
+ UNIPHIER_LD11_SYS_CLK_I2C,
+ UNIPHIER_LD11_SYS_CLK_STDMAC(8), /* HSC, MIO */
+ {
+ .name = "usb2",
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "ref",
+ .mult = 24,
+ .div = 25,
+ },
+ },
+ { /* sentinel */ }
+};
+
+const struct uniphier_clk_data uniphier_ld20_sys_clk_data[] = {
+ {
+ .name = "spll", /* 2000 MHz */
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "ref",
+ .mult = 80,
+ .div = 1,
+ },
+ },
+ {
+ .name = "uart",
+ .type = UNIPHIER_CLK_TYPE_FIXED_FACTOR,
+ .output_index = -1,
+ .data.factor = {
+ .parent_name = "spll",
+ .mult = 1,
+ .div = 34,
+ },
+ },
+ UNIPHIER_LD11_SYS_CLK_I2C,
+ UNIPHIER_LD20_SYS_CLK_SD,
+ UNIPHIER_LD11_SYS_CLK_STDMAC(8), /* HSC */
+ /* GIO is always clock-enabled: no function for 0x210c bit5 */
+ {
+ .name = "usb30",
+ .type = UNIPHIER_CLK_TYPE_GATE,
+ .output_index = 16,
+ .data.gate = {
+ .parent_name = NULL,
+ .reg = 0x210c,
+ /*
+ * clock for USB Link is enabled by the logic "OR"
+ * of bit 14 and bit 15. We do not use bit 15 here.
+ */
+ .mask = BIT(14),
+ },
+ },
+ {
+ .name = "usb30phy",
+ .type = UNIPHIER_CLK_TYPE_GATE,
+ .output_index = 18,
+ .data.gate = {
+ .parent_name = NULL,
+ .reg = 0x210c,
+ .mask = BIT(12) | BIT(13),
+ },
+ },
+ { /* sentinel */ }
+};
diff --git a/drivers/clk/uniphier/clk-uniphier.h b/drivers/clk/uniphier/clk-uniphier.h
index 364953c..be4fd92 100644
--- a/drivers/clk/uniphier/clk-uniphier.h
+++ b/drivers/clk/uniphier/clk-uniphier.h
@@ -80,4 +80,17 @@ struct clk_hw *uniphier_clk_register_mux(struct device *dev,
const char *name,
const struct uniphier_clk_mux_data *data);
+extern const struct uniphier_clk_data uniphier_sld3_sys_clk_data[];
+extern const struct uniphier_clk_data uniphier_ld4_sys_clk_data[];
+extern const struct uniphier_clk_data uniphier_pro4_sys_clk_data[];
+extern const struct uniphier_clk_data uniphier_sld8_sys_clk_data[];
+extern const struct uniphier_clk_data uniphier_pro5_sys_clk_data[];
+extern const struct uniphier_clk_data uniphier_pxs2_sys_clk_data[];
+extern const struct uniphier_clk_data uniphier_ld11_sys_clk_data[];
+extern const struct uniphier_clk_data uniphier_ld20_sys_clk_data[];
+extern const struct uniphier_clk_data uniphier_sld3_mio_clk_data[];
+extern const struct uniphier_clk_data uniphier_pro5_mio_clk_data[];
+extern const struct uniphier_clk_data uniphier_ld4_peri_clk_data[];
+extern const struct uniphier_clk_data uniphier_pro4_peri_clk_data[];
+
#endif /* __CLK_UNIPHIER_H__ */
--
1.9.1
^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH v5 0/2] clk: uniphier: add clock drivers for UniPhier SoCs
2016-07-26 18:09 [PATCH v5 0/2] clk: uniphier: add clock drivers for UniPhier SoCs Masahiro Yamada
2016-07-26 18:09 ` [PATCH v5 2/2] clk: uniphier: add clock data " Masahiro Yamada
@ 2016-07-28 2:25 ` Masahiro Yamada
1 sibling, 0 replies; 5+ messages in thread
From: Masahiro Yamada @ 2016-07-28 2:25 UTC (permalink / raw)
To: linux-clk
Cc: Mark Rutland, devicetree, Michael Turquette, Stephen Boyd,
Linux Kernel Mailing List, Masahiro Yamada, Rob Herring,
linux-arm-kernel
Hi.
I will send v6,
so please do not apply this version.
(meantime review is very appreciated, though.)
2016-07-27 3:09 GMT+09:00 Masahiro Yamada <yamada.masahiro@socionext.com>:
> I split into two patches to make review easier.
>
> 1/2: core support code
> 2/2: data arrays
>
>
> Changes in v5:
> - Rebase onto next-20160726 for easier git-am
>
> Changes in v4:
> - Unify module_platform_driver() boilerplate into a single place
> - Add binding document
> - Add USB3 clocks
>
> Changes in v3:
> - Change to platform drivers instead of OF_CLK_DECLARE
> - Split into a core part + SoC drivers
> SoC drivers just consist of tables of SoC-specific data.
> This allows reviewer to concentrate on the core-part
> - Hard-code parent clock names for cascading
>
> Changes in v2:
> - split emmc_hw_reset
> - make SD clock rate-controllable
> - add CLK_SET_RATE_PARENT flag to mux, gate, fixed-factor clocks
>
> Masahiro Yamada (2):
> clk: uniphier: add core support code for UniPhier clock drivers
> clk: uniphier: add clock data for UniPhier SoCs
>
> .../devicetree/bindings/clock/uniphier-clock.txt | 123 ++++
> MAINTAINERS | 1 +
> drivers/clk/Kconfig | 1 +
> drivers/clk/Makefile | 1 +
> drivers/clk/uniphier/Kconfig | 9 +
> drivers/clk/uniphier/Makefile | 9 +
> drivers/clk/uniphier/clk-uniphier-core.c | 216 +++++++
> drivers/clk/uniphier/clk-uniphier-fixed-factor.c | 49 ++
> drivers/clk/uniphier/clk-uniphier-fixed-rate.c | 48 ++
> drivers/clk/uniphier/clk-uniphier-gate.c | 97 ++++
> drivers/clk/uniphier/clk-uniphier-mio.c | 195 +++++++
> drivers/clk/uniphier/clk-uniphier-mux.c | 95 ++++
> drivers/clk/uniphier/clk-uniphier-peri.c | 95 ++++
> drivers/clk/uniphier/clk-uniphier-sys.c | 626 +++++++++++++++++++++
> drivers/clk/uniphier/clk-uniphier.h | 96 ++++
> 15 files changed, 1661 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/clock/uniphier-clock.txt
> create mode 100644 drivers/clk/uniphier/Kconfig
> create mode 100644 drivers/clk/uniphier/Makefile
> create mode 100644 drivers/clk/uniphier/clk-uniphier-core.c
> create mode 100644 drivers/clk/uniphier/clk-uniphier-fixed-factor.c
> create mode 100644 drivers/clk/uniphier/clk-uniphier-fixed-rate.c
> create mode 100644 drivers/clk/uniphier/clk-uniphier-gate.c
> create mode 100644 drivers/clk/uniphier/clk-uniphier-mio.c
> create mode 100644 drivers/clk/uniphier/clk-uniphier-mux.c
> create mode 100644 drivers/clk/uniphier/clk-uniphier-peri.c
> create mode 100644 drivers/clk/uniphier/clk-uniphier-sys.c
> create mode 100644 drivers/clk/uniphier/clk-uniphier.h
>
> --
> 1.9.1
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
--
Best Regards
Masahiro Yamada
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH v5 2/2] clk: uniphier: add clock data for UniPhier SoCs
2016-07-26 18:09 ` [PATCH v5 2/2] clk: uniphier: add clock data " Masahiro Yamada
@ 2016-07-29 20:13 ` Rob Herring
0 siblings, 0 replies; 5+ messages in thread
From: Rob Herring @ 2016-07-29 20:13 UTC (permalink / raw)
To: Masahiro Yamada
Cc: linux-clk, devicetree, Michael Turquette, Stephen Boyd,
linux-kernel, Mark Rutland, linux-arm-kernel
On Wed, Jul 27, 2016 at 03:09:53AM +0900, Masahiro Yamada wrote:
> Add clock data arrays for all UniPhier SoCs.
>
> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
> ---
>
> .../devicetree/bindings/clock/uniphier-clock.txt | 123 ++++
> drivers/clk/uniphier/Makefile | 3 +
> drivers/clk/uniphier/clk-uniphier-core.c | 91 +++
> drivers/clk/uniphier/clk-uniphier-mio.c | 195 +++++++
> drivers/clk/uniphier/clk-uniphier-peri.c | 95 ++++
> drivers/clk/uniphier/clk-uniphier-sys.c | 626 +++++++++++++++++++++
> drivers/clk/uniphier/clk-uniphier.h | 13 +
> 7 files changed, 1146 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/clock/uniphier-clock.txt
> create mode 100644 drivers/clk/uniphier/clk-uniphier-mio.c
> create mode 100644 drivers/clk/uniphier/clk-uniphier-peri.c
> create mode 100644 drivers/clk/uniphier/clk-uniphier-sys.c
>
> diff --git a/Documentation/devicetree/bindings/clock/uniphier-clock.txt b/Documentation/devicetree/bindings/clock/uniphier-clock.txt
> new file mode 100644
> index 0000000..1a4fee1
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/clock/uniphier-clock.txt
> @@ -0,0 +1,123 @@
> +UniPhier clock controller
> +
> +
> +System clock
> +------------
> +
> +Required properties:
> +- compatible: should be one of the following:
> + "socionext,uniphier-sld3-clock" - for PH1-sLD3 SoC.
> + "socionext,uniphier-ld4-clock" - for PH1-LD4 SoC.
> + "socionext,uniphier-pro4-clock" - for PH1-Pro4 SoC.
> + "socionext,uniphier-sld8-clock" - for PH1-sLD8 SoC.
> + "socionext,uniphier-pro5-clock" - for PH1-Pro5 SoC.
> + "socionext,uniphier-pxs2-clock" - for ProXstream2/PH1-LD6b SoC.
> + "socionext,uniphier-ld11-clock" - for PH1-LD11 SoC.
> + "socionext,uniphier-ld20-clock" - for PH1-LD20 SoC.
> +- #clock-cells: should be 1.
What are the provided clocks for this one?
> +
> +Note:
> +The clock node should be a child of a syscon node.
Of which syscon node?
> +
> +Example:
> +
> + sysctrl@61840000 {
> + compatible = "simple-mfd", "syscon";
This needs a specific compatible...
> + reg = <0x61840000 0x4000>;
> +
> + clock {
> + compatible = "socionext,uniphier-ld20-clock";
> + #clock-cells = <1>;
> + };
> +
> + other nodes ...
> + };
> +
> +
> +Media I/O (MIO) clock
> +---------------------
> +
> +Required properties:
> +- compatible: should be one of the following:
> + "socionext,uniphier-sld3-mio-clock" - for PH1-sLD3 SoC.
> + "socionext,uniphier-ld4-mio-clock" - for PH1-LD4 SoC.
> + "socionext,uniphier-pro4-mio-clock" - for PH1-Pro4 SoC.
> + "socionext,uniphier-sld8-mio-clock" - for PH1-sLD8 SoC.
> + "socionext,uniphier-pro5-mio-clock" - for PH1-Pro5 SoC.
> + "socionext,uniphier-pxs2-mio-clock" - for ProXstream2/PH1-LD6b SoC.
> + "socionext,uniphier-ld11-mio-clock" - for PH1-LD11 SoC.
> + "socionext,uniphier-ld20-mio-clock" - for PH1-LD20 SoC.
> +- #clock-cells: should be 1.
> +
> +Note:
> +The clock node should be a child of a syscon node.
Same issue here.
> +
> +Example:
> +
> + mioctrl@59810000 {
> + compatible = "simple-mfd", "syscon";
> + reg = <0x59810000 0x800>;
> +
> + clock {
> + compatible = "socionext,uniphier-ld20-mio-clock";
> + #clock-cells = <1>;
> + };
> +
> + other nodes ...
> + };
> +
> +Provided clocks:
> +
> +0: SD host ch0
> +1: eMMC host
> +2: SD host ch1
> +3: MIO DMAC
> +4: USB2 host ch0
> +5: USB2 host ch1
> +6: USB2 host ch2
> +7: USB2 host ch3
> +
> +
> +Peripheral clock
> +----------------
> +
> +Required properties:
> +- compatible: should be one of the following:
> + "socionext,uniphier-sld3-peri-clock" - for PH1-sLD3 SoC.
> + "socionext,uniphier-ld4-peri-clock" - for PH1-LD4 SoC.
> + "socionext,uniphier-pro4-peri-clock" - for PH1-Pro4 SoC.
> + "socionext,uniphier-sld8-peri-clock" - for PH1-sLD8 SoC.
> + "socionext,uniphier-pro5-peri-clock" - for PH1-Pro5 SoC.
> + "socionext,uniphier-pxs2-peri-clock" - for ProXstream2/PH1-LD6b SoC.
> + "socionext,uniphier-ld11-peri-clock" - for PH1-LD11 SoC.
> + "socionext,uniphier-ld20-peri-clock" - for PH1-LD20 SoC.
> +- #clock-cells: should be 1.
> +
> +Note:
> +The clock node should be a child of a syscon node.
> +
> +Example:
> +
> + perictrl@59820000 {
> + compatible = "simple-mfd", "syscon";
> + reg = <0x59820000 0x200>;
> +
> + clock {
> + compatible = "socionext,uniphier-ld20-peri-clock";
> + #clock-cells = <1>;
> + };
> +
> + other nodes ...
> + };
> +
> + 0: UART ch0
> + 1: UART ch1
> + 2: UART ch2
> + 3: UART ch3
> + 4: I2C ch0
> + 5: I2C ch1
> + 6: I2C ch2
> + 7: I2C ch3
> + 8: I2C ch4
> + 9: I2C ch5
> +10: I2C ch6
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH v5 0/2] clk: uniphier: add clock drivers for UniPhier SoCs
@ 2016-08-02 4:14 Masahiro Yamada
0 siblings, 0 replies; 5+ messages in thread
From: Masahiro Yamada @ 2016-08-02 4:14 UTC (permalink / raw)
To: linux-clk
Cc: Mark Rutland, devicetree, Greg Kroah-Hartman, Michael Turquette,
Stephen Boyd, linux-kernel, Masahiro Yamada, Rob Herring,
Geert Uytterhoeven, linux-arm-kernel, Andrew Morton,
David S. Miller, Guenter Roeck
I split into two patches to make review easier.
1/2: core support code
2/2: data arrays
Changes in v5:
- Assign each gating register bit with a separate clk
- Fix examples in binding document to add specific compatible
- Document provided clocks for system clock
Changes in v4:
- Unify module_platform_driver() boilerplate into a single place
- Add binding document
- Add USB3 clocks
Changes in v3:
- Change to platform drivers instead of OF_CLK_DECLARE
- Split into a core part + SoC drivers
SoC drivers just consist of tables of SoC-specific data.
This allows reviewer to concentrate on the core-part
- Hard-code parent clock names for cascading
Changes in v2:
- split emmc_hw_reset
- make SD clock rate-controllable
- add CLK_SET_RATE_PARENT flag to mux, gate, fixed-factor clocks
Masahiro Yamada (2):
clk: uniphier: add core support code for UniPhier clock driver
clk: uniphier: add clock data for UniPhier SoCs
.../devicetree/bindings/clock/uniphier-clock.txt | 134 +++++++++++++
MAINTAINERS | 1 +
drivers/clk/Kconfig | 1 +
drivers/clk/Makefile | 1 +
drivers/clk/uniphier/Kconfig | 9 +
drivers/clk/uniphier/Makefile | 9 +
drivers/clk/uniphier/clk-uniphier-core.c | 215 +++++++++++++++++++++
drivers/clk/uniphier/clk-uniphier-fixed-factor.c | 49 +++++
drivers/clk/uniphier/clk-uniphier-fixed-rate.c | 48 +++++
drivers/clk/uniphier/clk-uniphier-gate.c | 97 ++++++++++
drivers/clk/uniphier/clk-uniphier-mio.c | 103 ++++++++++
drivers/clk/uniphier/clk-uniphier-mux.c | 95 +++++++++
drivers/clk/uniphier/clk-uniphier-peri.c | 59 ++++++
drivers/clk/uniphier/clk-uniphier-sys.c | 151 +++++++++++++++
drivers/clk/uniphier/clk-uniphier.h | 122 ++++++++++++
15 files changed, 1094 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/uniphier-clock.txt
create mode 100644 drivers/clk/uniphier/Kconfig
create mode 100644 drivers/clk/uniphier/Makefile
create mode 100644 drivers/clk/uniphier/clk-uniphier-core.c
create mode 100644 drivers/clk/uniphier/clk-uniphier-fixed-factor.c
create mode 100644 drivers/clk/uniphier/clk-uniphier-fixed-rate.c
create mode 100644 drivers/clk/uniphier/clk-uniphier-gate.c
create mode 100644 drivers/clk/uniphier/clk-uniphier-mio.c
create mode 100644 drivers/clk/uniphier/clk-uniphier-mux.c
create mode 100644 drivers/clk/uniphier/clk-uniphier-peri.c
create mode 100644 drivers/clk/uniphier/clk-uniphier-sys.c
create mode 100644 drivers/clk/uniphier/clk-uniphier.h
--
1.9.1
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2016-08-02 4:14 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2016-07-26 18:09 [PATCH v5 0/2] clk: uniphier: add clock drivers for UniPhier SoCs Masahiro Yamada
2016-07-26 18:09 ` [PATCH v5 2/2] clk: uniphier: add clock data " Masahiro Yamada
2016-07-29 20:13 ` Rob Herring
2016-07-28 2:25 ` [PATCH v5 0/2] clk: uniphier: add clock drivers " Masahiro Yamada
-- strict thread matches above, loose matches on Subject: below --
2016-08-02 4:14 Masahiro Yamada
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).