* [PATCH RESEND 1/3] power: rt5033_battery: Add RT5033 Fuel gauge device driver
2015-01-06 5:45 [PATCH RESEND 0/3] power: rt5033: Add Richtek RT533 drivers Beomho Seo
@ 2015-01-06 5:45 ` Beomho Seo
2015-01-06 5:45 ` [PATCH RESEND 2/3] power: rt5033_charger: Add RT5033 charger " Beomho Seo
2015-01-06 5:45 ` [PATCH RESEND 3/3] Documentation: Add documentation for rt5033 multifunction device Beomho Seo
2 siblings, 0 replies; 7+ messages in thread
From: Beomho Seo @ 2015-01-06 5:45 UTC (permalink / raw)
To: linux-kernel, linux-pm, devicetree
Cc: lee.jone, broonie, sre, dbaryshkov, robh+dt, pawel.moll,
mark.rutland, ijc+devicetree, galak, cw00.choi, inki.dae,
sw0312.kim, Beomho Seo, David Woodhouse
This patch adds device driver of Richtek PMIC.
The driver support battery fuel gange. Fuel gauge calculates and determines the
battery state of charge(SOC) according to battery open circuit voltage(OCV).
Also, this driver provides battery average voltage, voltage and bettery present
property.
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
---
drivers/power/Kconfig | 8 ++
drivers/power/Makefile | 1 +
drivers/power/rt5033_battery.c | 177 ++++++++++++++++++++++++++++++++++++++++
3 files changed, 186 insertions(+)
create mode 100644 drivers/power/rt5033_battery.c
diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig
index 0108c2a..da6981f 100644
--- a/drivers/power/Kconfig
+++ b/drivers/power/Kconfig
@@ -397,6 +397,14 @@ config BATTERY_GOLDFISH
Say Y to enable support for the battery and AC power in the
Goldfish emulator.
+config BATTERY_RT5033
+ tristate "RT5033 fuel gauge support"
+ depends on MFD_RT5033
+ help
+ This adds support for battery fuel gauge in Richtek RT5033 PMIC.
+ The fuelgauge calculates and determines the battery state of charge
+ according to battery open circuit voltage.
+
source "drivers/power/reset/Kconfig"
endif # POWER_SUPPLY
diff --git a/drivers/power/Makefile b/drivers/power/Makefile
index dfa8942..b83a0c7 100644
--- a/drivers/power/Makefile
+++ b/drivers/power/Makefile
@@ -34,6 +34,7 @@ obj-$(CONFIG_BATTERY_DA9052) += da9052-battery.o
obj-$(CONFIG_BATTERY_MAX17040) += max17040_battery.o
obj-$(CONFIG_BATTERY_MAX17042) += max17042_battery.o
obj-$(CONFIG_BATTERY_Z2) += z2_battery.o
+obj-$(CONFIG_BATTERY_RT5033) += rt5033_battery.o
obj-$(CONFIG_BATTERY_S3C_ADC) += s3c_adc_battery.o
obj-$(CONFIG_BATTERY_TWL4030_MADC) += twl4030_madc_battery.o
obj-$(CONFIG_CHARGER_88PM860X) += 88pm860x_charger.o
diff --git a/drivers/power/rt5033_battery.c b/drivers/power/rt5033_battery.c
new file mode 100644
index 0000000..7b898f4
--- /dev/null
+++ b/drivers/power/rt5033_battery.c
@@ -0,0 +1,177 @@
+/*
+ * Fuel gauge driver for Richtek RT5033
+ *
+ * Copyright (C) 2014 Samsung Electronics, Co., Ltd.
+ * Author: Beomho Seo <beomho.seo@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published bythe Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/power_supply.h>
+#include <linux/mfd/rt5033-private.h>
+#include <linux/mfd/rt5033.h>
+
+static int rt5033_battery_get_capacity(struct i2c_client *client)
+{
+ struct rt5033_battery *battery = i2c_get_clientdata(client);
+ u32 msb;
+
+ regmap_read(battery->regmap, RT5033_FUEL_REG_SOC_H, &msb);
+
+ return msb;
+}
+
+static int rt5033_battery_get_present(struct i2c_client *client)
+{
+ struct rt5033_battery *battery = i2c_get_clientdata(client);
+ u32 val;
+
+ regmap_read(battery->regmap, RT5033_FUEL_REG_CONFIG_L, &val);
+
+ return (val & RT5033_FUEL_BAT_PRESENT) ? true : false;
+}
+
+static int rt5033_battery_get_watt_prop(struct i2c_client *client,
+ enum power_supply_property psp)
+{
+ struct rt5033_battery *battery = i2c_get_clientdata(client);
+ unsigned int regh, regl;
+ int ret;
+ u32 msb, lsb;
+
+ switch (psp) {
+ case POWER_SUPPLY_PROP_VOLTAGE_NOW:
+ regh = RT5033_FUEL_REG_VBAT_H;
+ regl = RT5033_FUEL_REG_VBAT_L;
+ break;
+ case POWER_SUPPLY_PROP_VOLTAGE_AVG:
+ regh = RT5033_FUEL_REG_AVG_VOLT_H;
+ regl = RT5033_FUEL_REG_AVG_VOLT_L;
+ break;
+ case POWER_SUPPLY_PROP_VOLTAGE_OCV:
+ regh = RT5033_FUEL_REG_OCV_H;
+ regl = RT5033_FUEL_REG_OCV_L;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ regmap_read(battery->regmap, regh, &msb);
+ regmap_read(battery->regmap, regl, &lsb);
+
+ ret = ((msb << 4) + (lsb >> 4)) * 1250 / 1000;
+
+ return ret;
+}
+
+static int rt5033_battery_get_property(struct power_supply *psy,
+ enum power_supply_property psp,
+ union power_supply_propval *val)
+{
+ struct rt5033_battery *battery = container_of(psy,
+ struct rt5033_battery, psy);
+
+ switch (psp) {
+ case POWER_SUPPLY_PROP_VOLTAGE_NOW:
+ case POWER_SUPPLY_PROP_VOLTAGE_AVG:
+ case POWER_SUPPLY_PROP_VOLTAGE_OCV:
+ val->intval = rt5033_battery_get_watt_prop(battery->client,
+ psp);
+ break;
+ case POWER_SUPPLY_PROP_PRESENT:
+ val->intval = rt5033_battery_get_present(battery->client);
+ break;
+ case POWER_SUPPLY_PROP_CAPACITY:
+ val->intval = rt5033_battery_get_capacity(battery->client);
+ break;
+ default:
+ return -EINVAL;
+ }
+ return 0;
+}
+
+static enum power_supply_property rt5033_battery_props[] = {
+ POWER_SUPPLY_PROP_VOLTAGE_NOW,
+ POWER_SUPPLY_PROP_VOLTAGE_AVG,
+ POWER_SUPPLY_PROP_VOLTAGE_OCV,
+ POWER_SUPPLY_PROP_PRESENT,
+ POWER_SUPPLY_PROP_CAPACITY,
+};
+
+static struct regmap_config rt5033_battery_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = RT5033_FUEL_REG_END,
+};
+
+static int rt5033_battery_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct i2c_adapter *adapter = to_i2c_adapter(client->dev.parent);
+ struct rt5033_battery *battery;
+ u32 ret;
+
+ if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE))
+ return -EIO;
+
+ battery = devm_kzalloc(&client->dev, sizeof(*battery), GFP_KERNEL);
+ if (!battery)
+ return -EINVAL;
+
+ battery->client = client;
+ battery->regmap = devm_regmap_init_i2c(client,
+ &rt5033_battery_regmap_config);
+ if (IS_ERR(battery->regmap)) {
+ dev_err(&client->dev, "Failed to initialize regmap\n");
+ return -EINVAL;
+ }
+
+ i2c_set_clientdata(client, battery);
+
+ battery->psy.name = "rt5033-battery";
+ battery->psy.type = POWER_SUPPLY_TYPE_BATTERY;
+ battery->psy.get_property = rt5033_battery_get_property;
+ battery->psy.properties = rt5033_battery_props;
+ battery->psy.num_properties = ARRAY_SIZE(rt5033_battery_props);
+
+ ret = power_supply_register(&client->dev, &battery->psy);
+ if (ret) {
+ dev_err(&client->dev, "Failed to register power supply\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static int rt5033_battery_remove(struct i2c_client *client)
+{
+ struct rt5033_battery *battery = i2c_get_clientdata(client);
+
+ power_supply_unregister(&battery->psy);
+
+ return 0;
+}
+
+static const struct i2c_device_id rt5033_battery_id[] = {
+ { "rt5033-battery", },
+ { }
+};
+MODULE_DEVICE_TABLE(platform, rt5033_battery_id);
+
+static struct i2c_driver rt5033_battery_driver = {
+ .driver = {
+ .name = "rt5033-battery",
+ },
+ .probe = rt5033_battery_probe,
+ .remove = rt5033_battery_remove,
+ .id_table = rt5033_battery_id,
+};
+module_i2c_driver(rt5033_battery_driver);
+
+MODULE_DESCRIPTION("Richtek RT5033 fuel gauge driver");
+MODULE_AUTHOR("Beomho Seo <beomho.seo@samsung.com>");
+MODULE_LICENSE("GPL");
--
1.7.9.5
^ permalink raw reply related [flat|nested] 7+ messages in thread* [PATCH RESEND 2/3] power: rt5033_charger: Add RT5033 charger device driver
2015-01-06 5:45 [PATCH RESEND 0/3] power: rt5033: Add Richtek RT533 drivers Beomho Seo
2015-01-06 5:45 ` [PATCH RESEND 1/3] power: rt5033_battery: Add RT5033 Fuel gauge device driver Beomho Seo
@ 2015-01-06 5:45 ` Beomho Seo
2015-01-06 5:45 ` [PATCH RESEND 3/3] Documentation: Add documentation for rt5033 multifunction device Beomho Seo
2 siblings, 0 replies; 7+ messages in thread
From: Beomho Seo @ 2015-01-06 5:45 UTC (permalink / raw)
To: linux-kernel, linux-pm, devicetree
Cc: lee.jone, broonie, sre, dbaryshkov, robh+dt, pawel.moll,
mark.rutland, ijc+devicetree, galak, cw00.choi, inki.dae,
sw0312.kim, Beomho Seo, David Woodhouse
This patch add device driver of Richtek RT5033 PMIC. The driver support
switching charger. rt5033 charger provide three charging mode.
Three charging mode are pre charge mode, fast cahrge mode and constant voltage
mode. They are have vary charge rate, charge parameters. The charge parameters
can be controlled by i2c interface.
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
---
drivers/power/Kconfig | 8 +
drivers/power/Makefile | 1 +
drivers/power/rt5033_charger.c | 485 ++++++++++++++++++++++++++++++++++++++++
3 files changed, 494 insertions(+)
create mode 100644 drivers/power/rt5033_charger.c
diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig
index da6981f..629b101 100644
--- a/drivers/power/Kconfig
+++ b/drivers/power/Kconfig
@@ -405,6 +405,14 @@ config BATTERY_RT5033
The fuelgauge calculates and determines the battery state of charge
according to battery open circuit voltage.
+config CHARGER_RT5033
+ tristate "RT5033 battery charger support"
+ depends on MFD_RT5033
+ help
+ This adds support for battery charger in Richtek RT5033 PMIC.
+ The device supports pre-charge mode, fast charge mode and
+ constant voltage mode.
+
source "drivers/power/reset/Kconfig"
endif # POWER_SUPPLY
diff --git a/drivers/power/Makefile b/drivers/power/Makefile
index b83a0c7..bb8cce3 100644
--- a/drivers/power/Makefile
+++ b/drivers/power/Makefile
@@ -57,6 +57,7 @@ obj-$(CONFIG_CHARGER_BQ2415X) += bq2415x_charger.o
obj-$(CONFIG_CHARGER_BQ24190) += bq24190_charger.o
obj-$(CONFIG_CHARGER_BQ24735) += bq24735-charger.o
obj-$(CONFIG_POWER_AVS) += avs/
+obj-$(CONFIG_POWER_RT5033) += rt5033_charger.o
obj-$(CONFIG_CHARGER_SMB347) += smb347-charger.o
obj-$(CONFIG_CHARGER_TPS65090) += tps65090-charger.o
obj-$(CONFIG_POWER_RESET) += reset/
diff --git a/drivers/power/rt5033_charger.c b/drivers/power/rt5033_charger.c
new file mode 100644
index 0000000..9dcaef4
--- /dev/null
+++ b/drivers/power/rt5033_charger.c
@@ -0,0 +1,485 @@
+/*
+ * Battery charger driver for RT5033
+ *
+ * Copyright (C) 2014 Samsung Electronics, Co., Ltd.
+ * Author: Beomho Seo <beomho.seo@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published bythe Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/power_supply.h>
+#include <linux/mfd/rt5033-private.h>
+#include <linux/mfd/rt5033.h>
+
+static int rt5033_get_charger_state(struct rt5033_charger *charger)
+{
+ struct regmap *regmap = charger->rt5033->regmap;
+ int state = POWER_SUPPLY_STATUS_UNKNOWN;
+ u32 reg_data;
+
+ if (!regmap)
+ return state;
+
+ regmap_read(regmap, RT5033_REG_CHG_STAT, ®_data);
+
+ switch (reg_data & RT5033_CHG_STAT_MASK) {
+ case RT5033_CHG_STAT_DISCHARGING:
+ state = POWER_SUPPLY_STATUS_DISCHARGING;
+ break;
+ case RT5033_CHG_STAT_CHARGING:
+ state = POWER_SUPPLY_STATUS_CHARGING;
+ break;
+ case RT5033_CHG_STAT_FULL:
+ state = POWER_SUPPLY_STATUS_FULL;
+ break;
+ case RT5033_CHG_STAT_NOT_CHARGING:
+ state = POWER_SUPPLY_STATUS_NOT_CHARGING;
+ break;
+ }
+
+ return state;
+}
+
+static int rt5033_get_charger_type(struct rt5033_charger *charger)
+{
+ struct regmap *regmap = charger->rt5033->regmap;
+ int state = POWER_SUPPLY_CHARGE_TYPE_UNKNOWN;
+ u32 reg_data;
+
+ regmap_read(regmap, RT5033_REG_CHG_STAT, ®_data);
+
+ switch (reg_data & RT5033_CHG_STAT_TYPE_MASK) {
+ case RT5033_CHG_STAT_TYPE_FAST:
+ state = POWER_SUPPLY_CHARGE_TYPE_FAST;
+ break;
+ case RT5033_CHG_STAT_TYPE_PRE:
+ state = POWER_SUPPLY_CHARGE_TYPE_TRICKLE;
+ break;
+ }
+
+ return state;
+}
+
+static int rt5033_get_charger_current(struct rt5033_charger *charger,
+ enum power_supply_property psp)
+{
+ struct regmap *regmap = charger->rt5033->regmap;
+ unsigned int state, reg_data, data;
+
+ if (psp == POWER_SUPPLY_PROP_CURRENT_MAX)
+ return RT5033_CHG_MAX_CURRENT;
+
+ regmap_read(regmap, RT5033_REG_CHG_CTRL5, ®_data);
+
+ state = (reg_data >> RT5033_CHGCTRL5_ICHG_SHIFT) & 0xf;
+
+ if (state > RT5033_CHG_MAX_CURRENT)
+ state = RT5033_CHG_MAX_CURRENT;
+
+ data = state * 100 + 700;
+
+ return data;
+}
+
+static int rt5033_get_charge_voltage(struct rt5033_charger *charger,
+ enum power_supply_property psp)
+{
+ struct regmap *regmap = charger->rt5033->regmap;
+ unsigned int state, reg_data, data;
+
+ if (psp == POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX)
+ return RT5033_CHARGER_CONST_VOLTAGE_LIMIT_MAX;
+
+ regmap_read(regmap, RT5033_REG_CHG_CTRL2, ®_data);
+
+ state = reg_data >> 2;
+
+ data = RT5033_CHARGER_CONST_VOLTAGE_LIMIT_MIN +
+ RT5033_CHARGER_CONST_VOLTAGE_STEP_NUM * state;
+
+ if (data > RT5033_CHARGER_CONST_VOLTAGE_LIMIT_MAX)
+ data = RT5033_CHARGER_CONST_VOLTAGE_LIMIT_MAX;
+
+ return data;
+}
+
+static inline int rt5033_init_const_charge(struct rt5033_charger *psy)
+{
+ struct rt5033_charger_data *chg = psy->chg;
+ unsigned val;
+ int ret;
+ u8 reg_data;
+
+ /* Set Constant voltage mode */
+ if (chg->const_uvolt < RT5033_CHARGER_CONST_VOLTAGE_LIMIT_MIN ||
+ chg->const_uvolt > RT5033_CHARGER_CONST_VOLTAGE_LIMIT_MAX)
+ return -EINVAL;
+
+ if (chg->const_uvolt == RT5033_CHARGER_CONST_VOLTAGE_LIMIT_MIN)
+ reg_data = 0x0;
+ else if (chg->const_uvolt == RT5033_CHARGER_CONST_VOLTAGE_LIMIT_MAX)
+ reg_data = 0xfc;
+ else {
+ val = chg->const_uvolt;
+ val -= RT5033_CHARGER_CONST_VOLTAGE_LIMIT_MIN;
+ val /= RT5033_CHARGER_CONST_VOLTAGE_STEP_NUM;
+ reg_data = val;
+ }
+
+ ret = regmap_update_bits(psy->rt5033->regmap, RT5033_REG_CHG_CTRL2,
+ RT5033_CHGCTRL2_CV_MASK, reg_data << 2);
+ if (ret) {
+ dev_err(psy->dev, "Failed regmap update\n");
+ return -EINVAL;
+ }
+
+ /* Set end of charge current */
+ if (chg->eoc_uamp < RT5033_CHARGER_EOC_MIN ||
+ chg->eoc_uamp > RT5033_CHARGER_EOC_MAX)
+ return -EINVAL;
+
+ if (chg->eoc_uamp == RT5033_CHARGER_EOC_MIN)
+ reg_data = 0x1;
+ else if (chg->eoc_uamp == RT5033_CHARGER_EOC_MAX)
+ reg_data = 0x7;
+ else {
+ val = chg->eoc_uamp;
+ if (val < RT5033_CHARGER_EOC_REF) {
+ val -= RT5033_CHARGER_EOC_MIN;
+ val /= RT5033_CHARGER_EOC_STEP_NUM1;
+ reg_data = 0x01 + val;
+ } else if (val > RT5033_CHARGER_EOC_REF) {
+ val -= RT5033_CHARGER_EOC_REF;
+ val /= RT5033_CHARGER_EOC_STEP_NUM2;
+ reg_data = 0x04 + val;
+ } else {
+ reg_data = 0x04;
+ }
+ }
+
+ ret = regmap_update_bits(psy->rt5033->regmap, RT5033_REG_CHG_CTRL4,
+ RT5033_CHGCTRL4_EOC_MASK, reg_data);
+ if (ret) {
+ dev_err(psy->dev, "Failed regmap update\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static inline int rt5033_init_fast_charge(struct rt5033_charger *psy)
+{
+ struct rt5033_charger_data *chg = psy->chg;
+ int ret;
+ u8 reg_data;
+
+ /* Set limit input current */
+ ret = regmap_update_bits(psy->rt5033->regmap, RT5033_REG_CHG_CTRL1,
+ RT5033_AICR_MODE_MASK, RT5033_AICR_2000_MODE);
+ if (ret) {
+ dev_err(psy->dev, "Failed regmap update\n");
+ return -EINVAL;
+ }
+
+ /* Set internal timer */
+ ret = regmap_update_bits(psy->rt5033->regmap, RT5033_REG_CHG_CTRL3,
+ RT5033_CHGCTRL3_TIMER_MASK | RT5033_CHGCTRL3_TIMER_EN_MASK,
+ RT5033_FAST_CHARGE_TIMER4 | RT5033_INT_TIMER_ENABLE);
+ if (ret) {
+ dev_err(psy->dev, "Failed regmap update\n");
+ return -EINVAL;
+ }
+
+ /* Set fast-charge mode Carging current */
+ if (chg->fast_uamp < RT5033_CHARGER_FAST_CURRENT_MIN ||
+ chg->fast_uamp > RT5033_CHARGER_FAST_CURRENT_MAX)
+ return -EINVAL;
+
+ if (chg->fast_uamp == RT5033_CHARGER_FAST_CURRENT_MIN)
+ reg_data = 0x0;
+ else if (chg->fast_uamp == RT5033_CHARGER_FAST_CURRENT_MAX)
+ reg_data = 0xd0;
+ else {
+ unsigned int val = chg->fast_uamp;
+
+ val -= RT5033_CHARGER_FAST_CURRENT_MIN;
+ val /= RT5033_CHARGER_FAST_CURRENT_STEP_NUM;
+ reg_data = 0x10 + val;
+ }
+
+ ret = regmap_update_bits(psy->rt5033->regmap, RT5033_REG_CHG_CTRL5,
+ RT5033_CHGCTRL5_ICHG_MASK, reg_data);
+ if (ret) {
+ dev_err(psy->dev, "Failed regmap update\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static inline int rt5033_init_pre_charge(struct rt5033_charger *psy)
+{
+ struct rt5033_charger_data *chg = psy->chg;
+ int ret;
+ u8 reg_data;
+
+ /* Set pre-charge threshold voltage */
+ if (chg->pre_uvolt < RT5033_CHARGER_PRE_THRESHOLD_LIMIT_MIN ||
+ chg->pre_uvolt > RT5033_CHARGER_PRE_THRESHOLD_LIMIT_MAX)
+ return -EINVAL;
+
+ if (chg->pre_uvolt == RT5033_CHARGER_PRE_THRESHOLD_LIMIT_MIN)
+ reg_data = 0x00;
+ else if (chg->pre_uvolt == RT5033_CHARGER_PRE_THRESHOLD_LIMIT_MAX)
+ reg_data = 0x0f;
+ else {
+ unsigned int val = chg->pre_uvolt;
+
+ val -= RT5033_CHARGER_PRE_THRESHOLD_LIMIT_MIN;
+ val /= RT5033_CHARGER_PRE_THRESHOLD_STEP_NUM;
+ reg_data = 0x00 + val;
+ }
+
+ ret = regmap_update_bits(psy->rt5033->regmap, RT5033_REG_CHG_CTRL5,
+ RT5033_CHGCTRL5_VPREC_MASK, reg_data);
+ if (ret) {
+ dev_err(psy->dev, "Failed regmap update\n");
+ return -EINVAL;
+ }
+
+ /* Set pre-charge mode charging current */
+ if (chg->pre_uamp < RT5033_CHARGER_PRE_CURRENT_LIMIT_MIN ||
+ chg->pre_uamp > RT5033_CHARGER_PRE_CURRENT_LIMIT_MAX)
+ return -EINVAL;
+
+ if (chg->pre_uamp == RT5033_CHARGER_PRE_CURRENT_LIMIT_MIN)
+ reg_data = 0x00;
+ else if (chg->pre_uamp == RT5033_CHARGER_PRE_CURRENT_LIMIT_MAX)
+ reg_data = 0x18;
+ else {
+ unsigned int val = chg->pre_uamp;
+
+ val -= RT5033_CHARGER_PRE_CURRENT_LIMIT_MIN;
+ val /= RT5033_CHARGER_PRE_CURRENT_STEP_NUM;
+ reg_data = 0x08 + val;
+ }
+
+ ret = regmap_update_bits(psy->rt5033->regmap, RT5033_REG_CHG_CTRL4,
+ RT5033_CHGCTRL4_IPREC_MASK, reg_data);
+ if (ret) {
+ dev_err(psy->dev, "Failed regmap update\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int rt5033_charger_reg_init(struct rt5033_charger *psy)
+{
+ int ret = 0;
+
+ ret = regmap_update_bits(psy->rt5033->regmap, RT5033_REG_CHG_CTRL1,
+ RT5033_CHGCTRL1_MODE_MASK, RT5033_CHARGER_MODE);
+ if (ret) {
+ dev_err(psy->dev, "Failed to update charger mode.\n");
+ return -EINVAL;
+ }
+
+ ret = regmap_update_bits(psy->rt5033->regmap, RT5033_REG_RT_CTRL1,
+ RT5033_RT_CTRL1_UUG_MASK, RT5033_CHARGER_UUG_ENABLE);
+ if (ret) {
+ dev_err(psy->dev, "Failed to update rt ctrl register.\n");
+ return -EINVAL;
+ }
+
+ ret = rt5033_init_pre_charge(psy);
+ if (ret)
+ return ret;
+
+ ret = rt5033_init_fast_charge(psy);
+ if (ret)
+ return ret;
+
+ ret = rt5033_init_const_charge(psy);
+ if (ret)
+ return ret;
+
+ ret = regmap_update_bits(psy->rt5033->regmap, RT5033_REG_CHG_CTRL3,
+ RT5033_CHGCTRL3_CFO_EN_MASK, RT5033_CFO_ENABLE);
+ if (ret) {
+ dev_err(psy->dev, "Failed to set enable.\n");
+ return -EINVAL;
+ }
+
+ ret = regmap_update_bits(psy->rt5033->regmap, RT5033_REG_CHG_CTRL1,
+ RT5033_RT_HZ_MASK, RT5033_CHARGER_HZ_DISABLE);
+ if (ret) {
+ dev_err(psy->dev, "Failed to set high impedance mode.\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static enum power_supply_property rt5033_charger_props[] = {
+ POWER_SUPPLY_PROP_STATUS,
+ POWER_SUPPLY_PROP_CHARGE_TYPE,
+ POWER_SUPPLY_PROP_CURRENT_NOW,
+ POWER_SUPPLY_PROP_CURRENT_MAX,
+ POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE,
+ POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX,
+ POWER_SUPPLY_PROP_MODEL_NAME,
+ POWER_SUPPLY_PROP_MANUFACTURER,
+};
+
+static int rt5033_charger_get_property(struct power_supply *psy,
+ enum power_supply_property psp,
+ union power_supply_propval *val)
+{
+ struct rt5033_charger *charger = container_of(psy,
+ struct rt5033_charger, psy);
+ int ret = 0;
+
+ switch (psp) {
+ case POWER_SUPPLY_PROP_STATUS:
+ val->intval = rt5033_get_charger_state(charger);
+ break;
+ case POWER_SUPPLY_PROP_CHARGE_TYPE:
+ val->intval = rt5033_get_charger_type(charger);
+ break;
+ case POWER_SUPPLY_PROP_CURRENT_NOW:
+ case POWER_SUPPLY_PROP_CURRENT_MAX:
+ val->intval = rt5033_get_charger_current(charger, psp);
+ break;
+ case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE:
+ case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX:
+ val->intval = rt5033_get_charge_voltage(charger, psp);
+ break;
+ case POWER_SUPPLY_PROP_MODEL_NAME:
+ val->strval = RT5033_CHARGER_MODEL;
+ break;
+ case POWER_SUPPLY_PROP_MANUFACTURER:
+ val->strval = RT5033_MANUFACTURER;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return ret;
+}
+
+static struct rt5033_charger_data *rt5033_charger_dt_init(
+ struct platform_device *pdev)
+{
+ struct rt5033_charger_data *chg;
+ struct device_node *np = pdev->dev.of_node;
+ int ret;
+
+ if (!np) {
+ dev_err(&pdev->dev, "No charger of_node\n");
+ return ERR_PTR(-EINVAL);
+ }
+
+ chg = devm_kzalloc(&pdev->dev, sizeof(*chg), GFP_KERNEL);
+ if (!chg)
+ return ERR_PTR(-ENOMEM);
+
+ ret = of_property_read_u32(np, "richtek,pre-uamp", &chg->pre_uamp);
+ if (ret)
+ return ERR_PTR(ret);
+
+ ret = of_property_read_u32(np, "richtek,pre-threshold-uvolt",
+ &chg->pre_uvolt);
+ if (ret)
+ return ERR_PTR(ret);
+
+ /*
+ * Charging current is decided by external sensing register and
+ * regulated voltage. In this driver, external sensing regster value
+ * is 10 mili ohm
+ */
+ ret = of_property_read_u32(np, "richtek,fast-uamp", &chg->fast_uamp);
+ if (ret)
+ return ERR_PTR(ret);
+
+ ret = of_property_read_u32(np, "richtek,const-uvolt",
+ &chg->const_uvolt);
+ if (ret)
+ return ERR_PTR(ret);
+
+ ret = of_property_read_u32(np, "richtek,eoc-uamp", &chg->eoc_uamp);
+ if (ret)
+ return ERR_PTR(ret);
+
+ return chg;
+}
+
+static int rt5033_charger_probe(struct platform_device *pdev)
+{
+ struct rt5033_charger *charger;
+ struct rt5033_dev *rt5033 = dev_get_drvdata(pdev->dev.parent);
+ int ret;
+
+ charger = devm_kzalloc(&pdev->dev, sizeof(*charger), GFP_KERNEL);
+ if (!charger)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, charger);
+ charger->dev = &pdev->dev;
+ charger->rt5033 = rt5033;
+
+ charger->chg = rt5033_charger_dt_init(pdev);
+ if (IS_ERR_OR_NULL(charger->chg))
+ return -ENODEV;
+
+ ret = rt5033_charger_reg_init(charger);
+ if (ret)
+ return ret;
+
+ charger->psy.name = "rt5033-charger",
+ charger->psy.type = POWER_SUPPLY_TYPE_BATTERY,
+ charger->psy.properties = rt5033_charger_props,
+ charger->psy.num_properties = ARRAY_SIZE(rt5033_charger_props),
+ charger->psy.get_property = rt5033_charger_get_property,
+
+ ret = power_supply_register(&pdev->dev, &charger->psy);
+ if (ret) {
+ dev_err(&pdev->dev, "Failed to register power supply\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static int rt5033_charger_remove(struct platform_device *pdev)
+{
+ struct rt5033_charger *charger = platform_get_drvdata(pdev);
+
+ power_supply_unregister(&charger->psy);
+
+ return 0;
+}
+
+static const struct platform_device_id rt5033_charger_id[] = {
+ { "rt5033-charger", },
+ { }
+};
+MODULE_DEVICE_TABLE(platform, rt5033_charger_id);
+
+static struct platform_driver rt5033_charger_driver = {
+ .driver = {
+ .name = "rt5033-charger",
+ },
+ .probe = rt5033_charger_probe,
+ .remove = rt5033_charger_remove,
+ .id_table = rt5033_charger_id,
+};
+module_platform_driver(rt5033_charger_driver);
+
+MODULE_DESCRIPTION("Richtek RT5033 charger driver");
+MODULE_AUTHOR("Beomho Seo <beomho.seo@samsung.com>");
+MODULE_LICENSE("GPL");
--
1.7.9.5
^ permalink raw reply related [flat|nested] 7+ messages in thread* [PATCH RESEND 3/3] Documentation: Add documentation for rt5033 multifunction device
2015-01-06 5:45 [PATCH RESEND 0/3] power: rt5033: Add Richtek RT533 drivers Beomho Seo
2015-01-06 5:45 ` [PATCH RESEND 1/3] power: rt5033_battery: Add RT5033 Fuel gauge device driver Beomho Seo
2015-01-06 5:45 ` [PATCH RESEND 2/3] power: rt5033_charger: Add RT5033 charger " Beomho Seo
@ 2015-01-06 5:45 ` Beomho Seo
2015-01-06 16:54 ` Rob Herring
2 siblings, 1 reply; 7+ messages in thread
From: Beomho Seo @ 2015-01-06 5:45 UTC (permalink / raw)
To: linux-kernel, linux-pm, devicetree
Cc: lee.jone, broonie, sre, dbaryshkov, robh+dt, pawel.moll,
mark.rutland, ijc+devicetree, galak, cw00.choi, inki.dae,
sw0312.kim, Beomho Seo, Lee Jones
This patch device tree binding documentation for rt5033 multifunction device.
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
---
Documentation/devicetree/bindings/mfd/rt5033.txt | 108 ++++++++++++++++++++
.../devicetree/bindings/vendor-prefixes.txt | 1 +
2 files changed, 109 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/rt5033.txt
diff --git a/Documentation/devicetree/bindings/mfd/rt5033.txt b/Documentation/devicetree/bindings/mfd/rt5033.txt
new file mode 100644
index 0000000..52a6d33
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/rt5033.txt
@@ -0,0 +1,108 @@
+Richtek RT5033 Power management Integrated Circuit
+
+RT5033 is a Multifunction device which includes battery charger, fuel gauge,
+flash LED current source, LDO and synchronous Buck converter for portable
+applications. It is interfaced to host controller using i2c interface.
+
+Required properties:
+- compatible : Must be "richtek,rt5033"
+- reg : Specifies the i2c slave address of general part.
+- interrupts : This i2c devices has an IRQ line connected to the main SoC.
+- interrupt-parent : The parent interrupt controller.
+
+Optional node:
+Regulators: The regulators of RT5033 have to be instantiated under sub-node
+named "regulators" usinge the following format.
+
+ regulators {
+ regulator-name {
+ regulator-name = LDO/BUCK
+ regulator subnodes called X, Y and Z
+ };
+ };
+ refer Documentation/devicetree/bindings/regulator/regulator.txt
+
+
+Battery charger: There battery charger of RT5033 have to be instantiated under
+sub-node named "charger" using the following format.
+
+Required properties:
+- compatible : Must be "richtek,rt5033-charger".
+- richtek,pre-uamp : Current of pre-charge mode. The pre-charge current levels
+ are 350 mA to 650 mA programmed by I2C per 100 mA.
+- richtek,pre-threshold-uvolt : Voltage of threshold pre-charge mode. Battery
+ voltage is below pre-charge threshold voltage, the charger is in pre-charge
+ mode with pre-charge current. Its levels are 2.3 V to 3.8 V programmed
+ by I2C per 0.1 V.
+- richtek,fast-uamp : Current of fast-charge mode. The fast-charge current
+ levels are 700 mA to 2000 mA programmed by I2C per 100 mA.
+- richtek,const-uvolt : Battery regulation voltage of constant voltage mode.
+ This voltage level 3.65 V to 4.4 V bye I2C per 0.025 V.
+- richtek,eoc-uamp : This property is end of charge current. Its level 150 mA
+ to 200 mA.
+
+ charger {
+ compatible = "richtek,rt5033-charger";
+ richtek,pre-uamp = <350000>;
+ richtek,pre-threshold-uvolt = <3400000>;
+ richtek,fast-uamp = <2000000>;
+ richtek,const-uvolt = <4350000>;
+ richtek,eoc-uamp = <250000>;
+ };
+
+
+Fuelgauge: There fuelgauge of RT5033 to be instantiated node named "fuelgauge"
+using the following format.
+
+Required properties:
+- compatible = Must be "richtek,rt5033-battery".
+
+ i2c_fuel: i2c@1 {
+ compatible = "i2c-gpio";
+ standard i2c-gpio constraints...
+ fuelgauge {
+ compatible = "richtek,rt5033-battery".
+ };
+ };
+
+
+Example:
+
+ rt5033@34 {
+ compatible = "richtek,rt5033";
+ reg = <0x34>;
+ interrupt-parent = <&gpx1>;
+ interrupts = <5 0>;
+
+ regulators {
+ buck_reg: BUCK {
+ regulator-name = "BUCK";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+ };
+
+ charger {
+ compatible = "richtek,rt5033-charger";
+ richtek,pre-uamp = <350000>;
+ richtek,pre-threshold-uvolt = <3400000>;
+ richtek,fast-uamp = <2000000>;
+ richtek,const-uvolt = <4350000>;
+ richtek,eoc-uamp = <250000>;
+ };
+
+ };
+
+ i2c_fuel: i2c@10 {
+ compatible = "i2c-gpio";
+ gpios = <&gpm3 1 0
+ &gpm3 0 0>;
+
+ fuel: rt5033-battery@35 {
+ compatible = "richtek,rt5033-battery";
+ interrupt-parent = <&gpx2>;
+ interrupts = <3 0>;
+ reg = <0x35>;
+ };
+ };
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 723999d..611b543 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -124,6 +124,7 @@ ralink Mediatek/Ralink Technology Corp.
ramtron Ramtron International
realtek Realtek Semiconductor Corp.
renesas Renesas Electronics Corporation
+richtek Richtek Technology Corporation
ricoh Ricoh Co. Ltd.
rockchip Fuzhou Rockchip Electronics Co., Ltd
samsung Samsung Semiconductor
--
1.7.9.5
^ permalink raw reply related [flat|nested] 7+ messages in thread