* [PATCH 0/4] add openpandora device support
@ 2015-02-12 13:03 Marek Belisko
2015-02-12 13:03 ` [PATCH 1/4] ARM: dts: omap3-pandora: add common device tree Marek Belisko
` (4 more replies)
0 siblings, 5 replies; 14+ messages in thread
From: Marek Belisko @ 2015-02-12 13:03 UTC (permalink / raw)
To: tony, bcousson
Cc: robh+dt, pawel.moll, mark.rutland, ijc+devicetree, galak,
devicetree, linux, linux-arm-kernel, linux-kernel, linux-omap,
marek
This series of patches adds initial device tree support for the
OpenPandora. The most important parts are working (display, keyboard,
touch, charging, fuel gauge, musb port, sd/mmc ports, leds, buttons).
Not yet supported are: usb host port, nubs, wifi, bluetooth, audio.
First patch add common dtsi file which is then used in 600mhz and 1ghz
variants of openpandora which support is added in patches 2 and 3.
H. Nikolaus Schaller (4):
ARM: dts: omap3-pandora: add common device tree
ARM: dts: omap3-pandora: add OMAP3530 600 MHz version
ARM: dts: omap3-pandora: add DM3730 1 GHz version
ARM: dts: omap3-pandora: include in dts Makefile
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/omap3-pandora-1ghz.dts | 65 +++
arch/arm/boot/dts/omap3-pandora-600mhz.dts | 65 +++
arch/arm/boot/dts/omap3-pandora-common.dtsi | 641 ++++++++++++++++++++++++++++
4 files changed, 773 insertions(+)
create mode 100644 arch/arm/boot/dts/omap3-pandora-1ghz.dts
create mode 100644 arch/arm/boot/dts/omap3-pandora-600mhz.dts
create mode 100644 arch/arm/boot/dts/omap3-pandora-common.dtsi
--
1.9.1
^ permalink raw reply [flat|nested] 14+ messages in thread* [PATCH 1/4] ARM: dts: omap3-pandora: add common device tree 2015-02-12 13:03 [PATCH 0/4] add openpandora device support Marek Belisko @ 2015-02-12 13:03 ` Marek Belisko 2015-02-12 16:03 ` Tony Lindgren 2015-02-12 17:47 ` Grazvydas Ignotas 2015-02-12 13:03 ` [PATCH 2/4] ARM: dts: omap3-pandora: add OMAP3530 600 MHz version Marek Belisko ` (3 subsequent siblings) 4 siblings, 2 replies; 14+ messages in thread From: Marek Belisko @ 2015-02-12 13:03 UTC (permalink / raw) To: tony, bcousson Cc: robh+dt, pawel.moll, mark.rutland, ijc+devicetree, galak, devicetree, linux, linux-arm-kernel, linux-kernel, linux-omap, marek, H. Nikolaus Schaller From: "H. Nikolaus Schaller" <hns@goldelico.com> This device tree allows to boot, supports the panel, framebuffer, touch screen, as well as some more peripherals. Since there is a OMAP3530 based 600 MHz variant and a DM3730 based 1 GHz variant we must include this common device tree code in one of two CPU specific device trees. Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Marek Belisko <marek@goldelico.com> --- arch/arm/boot/dts/omap3-pandora-common.dtsi | 641 ++++++++++++++++++++++++++++ 1 file changed, 641 insertions(+) create mode 100644 arch/arm/boot/dts/omap3-pandora-common.dtsi diff --git a/arch/arm/boot/dts/omap3-pandora-common.dtsi b/arch/arm/boot/dts/omap3-pandora-common.dtsi new file mode 100644 index 0000000..0a2a878 --- /dev/null +++ b/arch/arm/boot/dts/omap3-pandora-common.dtsi @@ -0,0 +1,641 @@ +/* + * Copyright (C) 2015 + * Nikolaus Schaller <hns@goldelico.com> + * + * Common device tree include for OpenPandora devices. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <dt-bindings/input/input.h> + +/ { + cpus { + cpu@0 { + cpu0-supply = <&vcc>; + }; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x20000000>; /* 512 MB */ + }; + + aliases { + display0 = &lcd; + }; + + tv: connector@1 { + compatible = "connector-analog-tv"; + label = "tv"; + + port { + tv_connector_in: endpoint { + remote-endpoint = <&venc_out>; + }; + }; + }; + + gpio-leds { + + compatible = "gpio-leds"; + + pinctrl-names = "default"; + pinctrl-0 = <&led_pins>; + + led@1 { + label = "pandora::sd1"; + gpios = <&gpio5 0 GPIO_ACTIVE_HIGH>; /* GPIO_128 */ + linux,default-trigger = "mmc0"; + default-state = "off"; + }; + + led@2 { + label = "pandora::sd2"; + gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>; /* GPIO_129 */ + linux,default-trigger = "mmc1"; + default-state = "off"; + }; + + led@3 { + label = "pandora::bluetooth"; + gpios = <&gpio5 30 GPIO_ACTIVE_HIGH>; /* GPIO_158 */ + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + led@4 { + label = "pandora::wifi"; + gpios = <&gpio5 31 GPIO_ACTIVE_HIGH>; /* GPIO_159 */ + linux,default-trigger = "mmc2"; + default-state = "off"; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&button_pins>; + + up-button { + label = "up"; + linux,code = <KEY_UP>; + gpios = <&gpio4 14 GPIO_ACTIVE_HIGH>; /* GPIO_110 */ + gpio-key,wakeup; + }; + + down-button { + label = "down"; + linux,code = <KEY_DOWN>; + gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* GPIO_103 */ + gpio-key,wakeup; + }; + + left-button { + label = "left"; + linux,code = <KEY_LEFT>; + gpios = <&gpio4 0 GPIO_ACTIVE_HIGH>; /* GPIO_96 */ + gpio-key,wakeup; + }; + + right-button { + label = "right"; + linux,code = <KEY_RIGHT>; + gpios = <&gpio4 2 GPIO_ACTIVE_HIGH>; /* GPIO_98 */ + gpio-key,wakeup; + }; + + pageup-button { + label = "game 1"; + linux,code = <KEY_PAGEUP>; + gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>; /* GPIO_109 */ + gpio-key,wakeup; + }; + + pagedown-button { + label = "game 3"; + linux,code = <KEY_PAGEDOWN>; + gpios = <&gpio4 10 GPIO_ACTIVE_HIGH>; /* GPIO_106 */ + gpio-key,wakeup; + }; + + home-button { + label = "game 4"; + linux,code = <KEY_HOME>; + gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>; /* GPIO_101 */ + gpio-key,wakeup; + }; + + end-button { + label = "game 2"; + linux,code = <KEY_END>; + gpios = <&gpio4 15 GPIO_ACTIVE_HIGH>; /* GPIO_111 */ + gpio-key,wakeup; + }; + + right-shift { + label = "l"; + linux,code = <KEY_RIGHTSHIFT>; + gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* GPIO_102 */ + gpio-key,wakeup; + }; + + kp-plus { + label = "l2"; + linux,code = <KEY_KPPLUS>; + gpios = <&gpio4 1 GPIO_ACTIVE_HIGH>; /* GPIO_97 */ + gpio-key,wakeup; + }; + + right-ctrl { + label = "r"; + linux,code = <KEY_RIGHTCTRL>; + gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>; /* GPIO_105 */ + gpio-key,wakeup; + }; + + kp-minus { + label = "r2"; + linux,code = <KEY_KPMINUS>; + gpios = <&gpio4 11 GPIO_ACTIVE_HIGH>; /* GPIO_107 */ + gpio-key,wakeup; + }; + + left-ctrl { + label = "ctrl"; + linux,code = <KEY_LEFTCTRL>; + gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* GPIO_104 */ + gpio-key,wakeup; + }; + + menu { + label = "menu"; + linux,code = <KEY_MENU>; + gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>; /* GPIO_99 */ + gpio-key,wakeup; + }; + + hold { + label = "hold"; + linux,code = <KEY_COFFEE>; + gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>; /* GPIO_176 */ + gpio-key,wakeup; + }; + + left-alt { + label = "alt"; + linux,code = <KEY_LEFTALT>; + gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>; /* GPIO_100 */ + gpio-key,wakeup; + }; + + lid { + label = "lid"; + linux,code = <0x00>; /* SW_LID lid shut */ + linux,input-type = <0x05>; /* EV_SW */ + gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>; /* GPIO_108 */ + gpio-key,wakeup; + }; + }; +}; + +&omap3_pmx_core { + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ + OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ + OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ + OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ + OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ + OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ + >; + }; + + mmc2_pins: pinmux_mmc2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ + OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ + OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ + OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ + OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ + OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ + OMAP3_CORE1_IOPAD(0x2164, PIN_OUTPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat4.sdmmc2_dirdat0 */ + OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat5.sdmmc2_dirdat1 */ + OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat6.sdmmc2_dircmd */ + OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE1) /* sdmmc2_dat7.sdmmc2_clkin */ + >; + }; + + dss_dpi_pins: pinmux_dss_dpi_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */ + OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */ + OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */ + OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */ + OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0) /* dss_data0.dss_data0 */ + OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0) /* dss_data1.dss_data1 */ + OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE0) /* dss_data2.dss_data2 */ + OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE0) /* dss_data3.dss_data3 */ + OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE0) /* dss_data4.dss_data4 */ + OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE0) /* dss_data5.dss_data5 */ + OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */ + OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */ + OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */ + OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */ + OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */ + OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */ + OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */ + OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */ + OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */ + OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */ + OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */ + OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */ + OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE0) /* dss_data18.dss_data18 */ + OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE0) /* dss_data19.dss_data19 */ + OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE0) /* dss_data20.dss_data20 */ + OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE0) /* dss_data21.dss_data21 */ + OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE0) /* dss_data22.dss_data22 */ + OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE0) /* dss_data23.dss_data23 */ + OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* GPIO_157 = lcd reset */ + >; + }; + + uart3_pins: pinmux_uart3_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ + OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ + >; + }; + + led_pins: pinmux_leds_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2154, PIN_OUTPUT | MUX_MODE4) /* GPIO_128 */ + OMAP3_CORE1_IOPAD(0x2156, PIN_OUTPUT | MUX_MODE4) /* GPIO_129 */ + OMAP3_CORE1_IOPAD(0x2190, PIN_OUTPUT | MUX_MODE4) /* GPIO_158 */ + OMAP3_CORE1_IOPAD(0x2192, PIN_OUTPUT | MUX_MODE4) /* GPIO_159 */ + >; + }; + + button_pins: pinmux_button_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2110, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_96 */ + OMAP3_CORE1_IOPAD(0x2112, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_97 */ + OMAP3_CORE1_IOPAD(0x2114, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_98 */ + OMAP3_CORE1_IOPAD(0x2116, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_99 */ + OMAP3_CORE1_IOPAD(0x2118, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_100 */ + OMAP3_CORE1_IOPAD(0x211a, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_101 */ + OMAP3_CORE1_IOPAD(0x211c, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_102 */ + OMAP3_CORE1_IOPAD(0x211e, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_103 */ + OMAP3_CORE1_IOPAD(0x2120, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_104 */ + OMAP3_CORE1_IOPAD(0x2122, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_105 */ + OMAP3_CORE1_IOPAD(0x2124, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_106 */ + OMAP3_CORE1_IOPAD(0x2126, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_107 */ + OMAP3_CORE1_IOPAD(0x2128, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_108 */ + OMAP3_CORE1_IOPAD(0x212a, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_109 */ + OMAP3_CORE1_IOPAD(0x212c, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_110 */ + OMAP3_CORE1_IOPAD(0x212e, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_111 */ + OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_176 */ + >; + }; + + penirq_pins: pinmux_penirq_pins { + pinctrl-single,pins = < + /* here we could enable to wakeup the cpu from suspend by a pen touch */ + OMAP3_CORE1_IOPAD(0x210c, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_94 */ + >; + }; + +}; + +&omap3_pmx_core2 { + /* define in CPU specific file that includes this one + * use either OMAP3430_CORE2_IOPAD() or OMAP3630_CORE2_IOPAD() + */ +}; + +&i2c1 { + clock-frequency = <2600000>; + + twl: twl@48 { + reg = <0x48>; + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ + interrupt-parent = <&intc>; + + twl_power: power { + compatible = "ti,twl4030-power-reset"; + ti,use_poweroff; + }; + + twl_audio: audio { + compatible = "ti,twl4030-audio"; + + codec { + ti,ramp_delay_value = <3>; + }; + }; + }; +}; + +#include "twl4030.dtsi" +#include "twl4030_omap3.dtsi" + +&twl_keypad { + keypad,num-rows = <8>; + keypad,num-columns = <6>; + linux,keymap = < + MATRIX_KEY(0, 0, KEY_9) + MATRIX_KEY(0, 1, KEY_8) + MATRIX_KEY(0, 2, KEY_I) + MATRIX_KEY(0, 3, KEY_J) + MATRIX_KEY(0, 4, KEY_N) + MATRIX_KEY(0, 5, KEY_M) + MATRIX_KEY(1, 0, KEY_0) + MATRIX_KEY(1, 1, KEY_7) + MATRIX_KEY(1, 2, KEY_U) + MATRIX_KEY(1, 3, KEY_H) + MATRIX_KEY(1, 4, KEY_B) + MATRIX_KEY(1, 5, KEY_SPACE) + MATRIX_KEY(2, 0, KEY_BACKSPACE) + MATRIX_KEY(2, 1, KEY_6) + MATRIX_KEY(2, 2, KEY_Y) + MATRIX_KEY(2, 3, KEY_G) + MATRIX_KEY(2, 4, KEY_V) + MATRIX_KEY(2, 5, KEY_FN) + MATRIX_KEY(3, 0, KEY_O) + MATRIX_KEY(3, 1, KEY_5) + MATRIX_KEY(3, 2, KEY_T) + MATRIX_KEY(3, 3, KEY_F) + MATRIX_KEY(3, 4, KEY_C) + MATRIX_KEY(4, 0, KEY_P) + MATRIX_KEY(4, 1, KEY_4) + MATRIX_KEY(4, 2, KEY_R) + MATRIX_KEY(4, 3, KEY_D) + MATRIX_KEY(4, 4, KEY_X) + MATRIX_KEY(5, 0, KEY_K) + MATRIX_KEY(5, 1, KEY_3) + MATRIX_KEY(5, 2, KEY_E) + MATRIX_KEY(5, 3, KEY_S) + MATRIX_KEY(5, 4, KEY_Z) + MATRIX_KEY(6, 0, KEY_L) + MATRIX_KEY(6, 1, KEY_2) + MATRIX_KEY(6, 2, KEY_W) + MATRIX_KEY(6, 3, KEY_A) + MATRIX_KEY(6, 4, KEY_RIGHTBRACE) + MATRIX_KEY(7, 0, KEY_ENTER) + MATRIX_KEY(7, 1, KEY_1) + MATRIX_KEY(7, 2, KEY_Q) + MATRIX_KEY(7, 3, KEY_LEFTSHIFT) + MATRIX_KEY(7, 4, KEY_LEFTBRACE ) + >; +}; + +/* backup battery charger */ +&charger { + ti,bb-uvolt = <3200000>; + ti,bb-uamp = <150>; +}; + +/* MMC2 */ +&vmmc2 { + regulator-min-microvolt = <1850000>; + regulator-max-microvolt = <3150000>; +}; + +/* LCD */ +&vaux1 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; +}; + +/* USB Host PHY */ +&vaux2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; +}; + +/* available on expansion connector */ +&vaux3 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; +}; + +/* ADS7846 and nubs */ +&vaux4 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; +}; + +/* power audio DAC and LID sensor */ +&vsim { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; +}; + +&i2c2 { + clock-frequency = <100000>; + /* no clients so we should disable clock */ +}; + +&i2c3 { + clock-frequency = <100000>; + + bq27500@55 { + compatible = "ti,bq27500"; + reg = <0x55>; + }; + +}; + +&usb_otg_hs { + interface-type = <0>; + usb-phy = <&usb2_phy>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; + mode = <3>; + power = <50>; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <&vmmc1>; + bus-width = <4>; + cd-gpios = <&twl_gpio 0 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>; /* GPIO_126 */ +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; + vmmc-supply = <&vmmc2>; + bus-width = <4>; + cd-gpios = <&twl_gpio 1 GPIO_ACTIVE_HIGH>; + wp-gpios = <&gpio4 31 GPIO_ACTIVE_LOW>; /* GPIO_127 */ +}; + +/* bluetooth*/ +&uart1 { +}; + +/* spare (expansion connector) */ +&uart2 { +}; + +/* console (expansion connector) */ +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; + interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>; +}; + +&usbhshost { + port2-mode = "ehci-phy"; +}; + +&gpmc { + ranges = <0 0 0x30000000 0x04>; /* CS0: NAND */ + + nand@0,0 { + reg = <0 0 0>; /* CS0, offset 0 */ + nand-bus-width = <16>; + ti,nand-ecc-opt = "sw"; + + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <44>; + gpmc,cs-wr-off-ns = <44>; + gpmc,adv-on-ns = <6>; + gpmc,adv-rd-off-ns = <34>; + gpmc,adv-wr-off-ns = <44>; + gpmc,we-off-ns = <40>; + gpmc,oe-off-ns = <54>; + gpmc,access-ns = <64>; + gpmc,rd-cycle-ns = <82>; + gpmc,wr-cycle-ns = <82>; + gpmc,wr-access-ns = <40>; + gpmc,wr-data-mux-bus-ns = <0>; + gpmc,device-width = <2>; + + #address-cells = <1>; + #size-cells = <1>; + + /* u-boot uses mtdparts=nand:512k(xloader),1920k(uboot),128k(uboot-env),10m(boot),-(rootfs) */ + + x-loader@0 { + label = "xloader"; + reg = <0 0x80000>; + }; + + bootloaders@80000 { + label = "uboot"; + reg = <0x80000 0x1e0000>; + }; + + bootloaders_env@260000 { + label = "uboot-env"; + reg = <0x260000 0x20000>; + }; + + kernel@280000 { + label = "boot"; + reg = <0x280000 0xa00000>; + }; + + filesystem@680000 { + label = "rootfs"; + reg = <0xc80000 0>; /* 0 = MTDPART_SIZ_FULL */ + }; + }; +}; + +&mcspi1 { + tsc2046@0 { + reg = <0>; /* CS0 */ + compatible = "ti,tsc2046"; + spi-max-frequency = <1000000>; + pinctrl-names = "default"; + pinctrl-0 = <&penirq_pins>; + interrupt-parent = <&gpio3>; + interrupts = <30 0>; /* GPIO_94 */ + pendown-gpio = <&gpio3 30 0>; + vcc-supply = <&vaux4>; + + ti,x-min = /bits/ 16 <0>; + ti,x-max = /bits/ 16 <8000>; + ti,y-min = /bits/ 16 <0>; + ti,y-max = /bits/ 16 <4800>; + ti,x-plate-ohms = /bits/ 16 <40>; + ti,pressure-max = /bits/ 16 <255>; + + linux,wakeup; + }; + + lcd: lcd@1 { + reg = <1>; /* CS1 */ + compatible = "omapdss,tpo,td043mtea1"; + spi-max-frequency = <100000>; + spi-cpol; + spi-cpha; + + label = "lcd"; + reset-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>; /* GPIO_157 */ + vcc-supply = <&vaux1>; + + port { + lcd_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + }; + + +}; + +/* n/a - used as GPIOs */ +&mcbsp1 { +}; + +/* audio DAC */ +&mcbsp2 { +}; + +/* bluetooth */ +&mcbsp3 { +}; + +/* to twl4030*/ +&mcbsp4 { +}; + +&venc { + status = "ok"; + + vdda-supply = <&vdac>; + + port { + venc_out: endpoint { + remote-endpoint = <&tv_connector_in>; + ti,channels = <2>; + }; + }; +}; + +&dss { + pinctrl-names = "default"; + pinctrl-0 = < &dss_dpi_pins >; + + status = "ok"; + vdds_dsi-supply = <&vpll2>; + + port { + dpi_out: endpoint { + remote-endpoint = <&lcd_in>; + data-lines = <24>; + }; + }; +}; -- 1.9.1 ^ permalink raw reply related [flat|nested] 14+ messages in thread
* Re: [PATCH 1/4] ARM: dts: omap3-pandora: add common device tree 2015-02-12 13:03 ` [PATCH 1/4] ARM: dts: omap3-pandora: add common device tree Marek Belisko @ 2015-02-12 16:03 ` Tony Lindgren 2015-02-12 16:29 ` Dr. H. Nikolaus Schaller 2015-02-12 17:47 ` Grazvydas Ignotas 1 sibling, 1 reply; 14+ messages in thread From: Tony Lindgren @ 2015-02-12 16:03 UTC (permalink / raw) To: Marek Belisko Cc: bcousson, robh+dt, pawel.moll, mark.rutland, ijc+devicetree, galak, devicetree, linux, linux-arm-kernel, linux-kernel, linux-omap, H. Nikolaus Schaller Hi, Few comments below. * Marek Belisko <marek@goldelico.com> [150212 05:07]: > + > +&omap3_pmx_core { > + > + mmc1_pins: pinmux_mmc1_pins { > + pinctrl-single,pins = < > + OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ > + OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ > + OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ > + OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ > + OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ > + OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ > + >; ... > +&omap3_pmx_core2 { > + /* define in CPU specific file that includes this one > + * use either OMAP3430_CORE2_IOPAD() or OMAP3630_CORE2_IOPAD() > + */ > +}; OK looks like you have some SoC specific pins too.. I assume you guys have checked that all the pins defined in this file are at the same offset between 34xx and 36xx variants? > +&i2c1 { > + clock-frequency = <2600000>; > + > + twl: twl@48 { > + reg = <0x48>; > + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ > + interrupt-parent = <&intc>; > + > + twl_power: power { > + compatible = "ti,twl4030-power-reset"; > + ti,use_poweroff; > + }; > + > + twl_audio: audio { > + compatible = "ti,twl4030-audio"; > + > + codec { > + ti,ramp_delay_value = <3>; > + }; > + }; > + }; > +}; Can be done later naturally, but ere you probably want ti,twl4030-power-idle or ti,twl4030-power-idle-osc-off if the osicllator can be shut down during off-idle. > +&gpmc { > + ranges = <0 0 0x30000000 0x04>; /* CS0: NAND */ The ranges here allocate the GPMC partition, so it needs to be a minimum of 16MB: ranges = <0 0 0x30000000 0x1000000>, /* CS0: 16MB for NAND */ > + nand@0,0 { > + reg = <0 0 0>; /* CS0, offset 0 */ The reg is for the device driver to ioremap it's registers, for NAND it's just 4: reg = <0 0 4>; /* CS0, offset 0, IO size 4 */ > + filesystem@680000 { > + label = "rootfs"; > + reg = <0xc80000 0>; /* 0 = MTDPART_SIZ_FULL */ > + }; > + }; > +}; Is the NAND the same size on all of them? I don't think dts has a binding for MTDPART_SIZ_FULL type thing.. > + lcd: lcd@1 { > + reg = <1>; /* CS1 */ > + compatible = "omapdss,tpo,td043mtea1"; > + spi-max-frequency = <100000>; > + spi-cpol; > + spi-cpha; > + > + label = "lcd"; > + reset-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>; /* GPIO_157 */ > + vcc-supply = <&vaux1>; > + > + port { > + lcd_in: endpoint { > + remote-endpoint = <&dpi_out>; > + }; > + }; > + }; Oh there's already a binding for the LCD too? That's great :) Nine job, good to see this happening! Regards, Tony ^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 1/4] ARM: dts: omap3-pandora: add common device tree 2015-02-12 16:03 ` Tony Lindgren @ 2015-02-12 16:29 ` Dr. H. Nikolaus Schaller 2015-02-12 16:52 ` Tony Lindgren 0 siblings, 1 reply; 14+ messages in thread From: Dr. H. Nikolaus Schaller @ 2015-02-12 16:29 UTC (permalink / raw) To: Tony Lindgren Cc: mark.rutland, devicetree, linux, pawel.moll, ijc+devicetree, linux-kernel, robh+dt, bcousson, galak, Marek Belisko, linux-omap, linux-arm-kernel Am 12.02.2015 um 17:03 schrieb Tony Lindgren <tony@atomide.com>: > Hi, > > Few comments below. > > * Marek Belisko <marek@goldelico.com> [150212 05:07]: >> + >> +&omap3_pmx_core { >> + >> + mmc1_pins: pinmux_mmc1_pins { >> + pinctrl-single,pins = < >> + OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ >> + OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ >> + OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ >> + OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ >> + OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ >> + OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ >> + >; > ... > >> +&omap3_pmx_core2 { >> + /* define in CPU specific file that includes this one >> + * use either OMAP3430_CORE2_IOPAD() or OMAP3630_CORE2_IOPAD() >> + */ >> +}; > > OK looks like you have some SoC specific pins too.. I assume you > guys have checked that all the pins defined in this file are at > the same offset between 34xx and 36xx variants? Yes. All in this file are common between 34xx and 36xx. The 600mhz / 1ghz files cover the differences for pmx_core2 through the different macros (OMAP3430_CORE2_IOPAD vs. OMAP3460_CORE2_IOPAD). > >> +&i2c1 { >> + clock-frequency = <2600000>; >> + >> + twl: twl@48 { >> + reg = <0x48>; >> + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ >> + interrupt-parent = <&intc>; >> + >> + twl_power: power { >> + compatible = "ti,twl4030-power-reset"; >> + ti,use_poweroff; >> + }; >> + >> + twl_audio: audio { >> + compatible = "ti,twl4030-audio"; >> + >> + codec { >> + ti,ramp_delay_value = <3>; >> + }; >> + }; >> + }; >> +}; > > Can be done later naturally, but ere you probably want > ti,twl4030-power-idle or ti,twl4030-power-idle-osc-off > if the osicllator can be shut down during off-idle. Good hint. We have to check and test if it can be shut down. But as said, this is just the beginning of DT support. > >> +&gpmc { >> + ranges = <0 0 0x30000000 0x04>; /* CS0: NAND */ > > The ranges here allocate the GPMC partition, so it needs to be > a minimum of 16MB: > > ranges = <0 0 0x30000000 0x1000000>, /* CS0: 16MB for NAND */ > >> + nand@0,0 { >> + reg = <0 0 0>; /* CS0, offset 0 */ > > The reg is for the device driver to ioremap it's registers, > for NAND it's just 4: > > reg = <0 0 4>; /* CS0, offset 0, IO size 4 */ Ok, that was a typo and we have not tested how compatible it is to the board file scheme. > >> + filesystem@680000 { >> + label = "rootfs"; >> + reg = <0xc80000 0>; /* 0 = MTDPART_SIZ_FULL */ >> + }; >> + }; >> +}; > > Is the NAND the same size on all of them? AFAIK not necessarily. > I don't think dts > has a binding for MTDPART_SIZ_FULL type thing.. It does not need a special binding, we just set the size to 0. This is interpreted as MTDPART_SIZ_FULL later on. For board files, there is just a #define in include/linux/mtd/partitions.h and it appears to work. > >> + lcd: lcd@1 { >> + reg = <1>; /* CS1 */ >> + compatible = "omapdss,tpo,td043mtea1"; >> + spi-max-frequency = <100000>; >> + spi-cpol; >> + spi-cpha; >> + >> + label = "lcd"; >> + reset-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>; /* GPIO_157 */ >> + vcc-supply = <&vaux1>; >> + >> + port { >> + lcd_in: endpoint { >> + remote-endpoint = <&dpi_out>; >> + }; >> + }; >> + }; > > Oh there's already a binding for the LCD too? That’s great :) Yes, we were happy to find that the panel driver has already been upgraded for DT use. > > Nine job, good to see this happening! > > Regards, > > > Tony BR, Nikolaus ^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 1/4] ARM: dts: omap3-pandora: add common device tree 2015-02-12 16:29 ` Dr. H. Nikolaus Schaller @ 2015-02-12 16:52 ` Tony Lindgren 0 siblings, 0 replies; 14+ messages in thread From: Tony Lindgren @ 2015-02-12 16:52 UTC (permalink / raw) To: Dr. H. Nikolaus Schaller Cc: Marek Belisko, bcousson, robh+dt, pawel.moll, mark.rutland, ijc+devicetree, galak, devicetree, linux, linux-arm-kernel, linux-kernel, linux-omap * Dr. H. Nikolaus Schaller <hns@goldelico.com> [150212 08:34]: > Am 12.02.2015 um 17:03 schrieb Tony Lindgren <tony@atomide.com>: > > > I don't think dts > > has a binding for MTDPART_SIZ_FULL type thing.. > > It does not need a special binding, we just set the size to 0. This > is interpreted as MTDPART_SIZ_FULL later on. For board files, > there is just a #define in include/linux/mtd/partitions.h and it appears > to work. Oh OK good to know. Regards, Tony ^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 1/4] ARM: dts: omap3-pandora: add common device tree 2015-02-12 13:03 ` [PATCH 1/4] ARM: dts: omap3-pandora: add common device tree Marek Belisko 2015-02-12 16:03 ` Tony Lindgren @ 2015-02-12 17:47 ` Grazvydas Ignotas 2015-02-12 20:09 ` Dr. H. Nikolaus Schaller 1 sibling, 1 reply; 14+ messages in thread From: Grazvydas Ignotas @ 2015-02-12 17:47 UTC (permalink / raw) To: Marek Belisko Cc: Tony Lindgren, bcousson, Mark Rutland, devicetree, Russell King - ARM Linux, pawel.moll, ijc+devicetree, H. Nikolaus Schaller, linux-kernel@vger.kernel.org, robh+dt, galak, linux-omap@vger.kernel.org, linux-arm-kernel@lists.infradead.org On Thu, Feb 12, 2015 at 3:03 PM, Marek Belisko <marek@goldelico.com> wrote: > From: "H. Nikolaus Schaller" <hns@goldelico.com> > > This device tree allows to boot, supports the panel, > framebuffer, touch screen, as well as some more peripherals. > Since there is a OMAP3530 based 600 MHz variant and a DM3730 based > 1 GHz variant we must include this common device tree code > in one of two CPU specific device trees. > > Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> > Signed-off-by: Marek Belisko <marek@goldelico.com> > --- > arch/arm/boot/dts/omap3-pandora-common.dtsi | 641 ++++++++++++++++++++++++++++ > 1 file changed, 641 insertions(+) > create mode 100644 arch/arm/boot/dts/omap3-pandora-common.dtsi > > diff --git a/arch/arm/boot/dts/omap3-pandora-common.dtsi b/arch/arm/boot/dts/omap3-pandora-common.dtsi > new file mode 100644 > index 0000000..0a2a878 > --- /dev/null > +++ b/arch/arm/boot/dts/omap3-pandora-common.dtsi > @@ -0,0 +1,641 @@ ... > + > + gpio-leds { > + > + compatible = "gpio-leds"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&led_pins>; > + > + led@1 { > + label = "pandora::sd1"; > + gpios = <&gpio5 0 GPIO_ACTIVE_HIGH>; /* GPIO_128 */ > + linux,default-trigger = "mmc0"; > + default-state = "off"; > + }; > + > + led@2 { > + label = "pandora::sd2"; > + gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>; /* GPIO_129 */ > + linux,default-trigger = "mmc1"; > + default-state = "off"; > + }; > + > + led@3 { > + label = "pandora::bluetooth"; > + gpios = <&gpio5 30 GPIO_ACTIVE_HIGH>; /* GPIO_158 */ > + linux,default-trigger = "heartbeat"; I'd prefer this had no trigger, but no strong feelings here. > + default-state = "off"; > + }; > + > + led@4 { > + label = "pandora::wifi"; > + gpios = <&gpio5 31 GPIO_ACTIVE_HIGH>; /* GPIO_159 */ > + linux,default-trigger = "mmc2"; > + default-state = "off"; > + }; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&button_pins>; > + > + up-button { > + label = "up"; > + linux,code = <KEY_UP>; > + gpios = <&gpio4 14 GPIO_ACTIVE_HIGH>; /* GPIO_110 */ > + gpio-key,wakeup; > + }; > + > + down-button { > + label = "down"; > + linux,code = <KEY_DOWN>; > + gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* GPIO_103 */ > + gpio-key,wakeup; > + }; > + > + left-button { > + label = "left"; > + linux,code = <KEY_LEFT>; > + gpios = <&gpio4 0 GPIO_ACTIVE_HIGH>; /* GPIO_96 */ > + gpio-key,wakeup; > + }; > + > + right-button { > + label = "right"; > + linux,code = <KEY_RIGHT>; > + gpios = <&gpio4 2 GPIO_ACTIVE_HIGH>; /* GPIO_98 */ > + gpio-key,wakeup; > + }; > + > + pageup-button { > + label = "game 1"; > + linux,code = <KEY_PAGEUP>; > + gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>; /* GPIO_109 */ > + gpio-key,wakeup; > + }; > + > + pagedown-button { > + label = "game 3"; > + linux,code = <KEY_PAGEDOWN>; > + gpios = <&gpio4 10 GPIO_ACTIVE_HIGH>; /* GPIO_106 */ > + gpio-key,wakeup; > + }; > + > + home-button { > + label = "game 4"; > + linux,code = <KEY_HOME>; > + gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>; /* GPIO_101 */ > + gpio-key,wakeup; > + }; > + > + end-button { > + label = "game 2"; > + linux,code = <KEY_END>; > + gpios = <&gpio4 15 GPIO_ACTIVE_HIGH>; /* GPIO_111 */ > + gpio-key,wakeup; > + }; > + > + right-shift { > + label = "l"; > + linux,code = <KEY_RIGHTSHIFT>; > + gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* GPIO_102 */ > + gpio-key,wakeup; > + }; > + > + kp-plus { > + label = "l2"; > + linux,code = <KEY_KPPLUS>; > + gpios = <&gpio4 1 GPIO_ACTIVE_HIGH>; /* GPIO_97 */ > + gpio-key,wakeup; > + }; > + > + right-ctrl { > + label = "r"; > + linux,code = <KEY_RIGHTCTRL>; > + gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>; /* GPIO_105 */ > + gpio-key,wakeup; > + }; > + > + kp-minus { > + label = "r2"; > + linux,code = <KEY_KPMINUS>; > + gpios = <&gpio4 11 GPIO_ACTIVE_HIGH>; /* GPIO_107 */ > + gpio-key,wakeup; > + }; > + > + left-ctrl { > + label = "ctrl"; > + linux,code = <KEY_LEFTCTRL>; > + gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* GPIO_104 */ > + gpio-key,wakeup; > + }; > + > + menu { > + label = "menu"; > + linux,code = <KEY_MENU>; > + gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>; /* GPIO_99 */ > + gpio-key,wakeup; > + }; > + > + hold { > + label = "hold"; > + linux,code = <KEY_COFFEE>; > + gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>; /* GPIO_176 */ > + gpio-key,wakeup; > + }; > + > + left-alt { > + label = "alt"; > + linux,code = <KEY_LEFTALT>; > + gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>; /* GPIO_100 */ > + gpio-key,wakeup; > + }; > + > + lid { > + label = "lid"; > + linux,code = <0x00>; /* SW_LID lid shut */ > + linux,input-type = <0x05>; /* EV_SW */ > + gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>; /* GPIO_108 */ > + gpio-key,wakeup; > + }; This is not right, all button GPIOs are active low except GPIO_100, which is active high. GPIO_108 should not have the wakeup flag set because lid switch power is normally cut during low power modes. ... > + > + dss_dpi_pins: pinmux_dss_dpi_pins { > + pinctrl-single,pins = < > + OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */ > + OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */ > + OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */ > + OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */ > + OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0) /* dss_data0.dss_data0 */ > + OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0) /* dss_data1.dss_data1 */ > + OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE0) /* dss_data2.dss_data2 */ > + OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE0) /* dss_data3.dss_data3 */ > + OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE0) /* dss_data4.dss_data4 */ > + OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE0) /* dss_data5.dss_data5 */ > + OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */ > + OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */ > + OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */ > + OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */ > + OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */ > + OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */ > + OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */ > + OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */ > + OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */ > + OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */ > + OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */ > + OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */ > + OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE0) /* dss_data18.dss_data18 */ > + OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE0) /* dss_data19.dss_data19 */ > + OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE0) /* dss_data20.dss_data20 */ > + OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE0) /* dss_data21.dss_data21 */ > + OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE0) /* dss_data22.dss_data22 */ > + OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE0) /* dss_data23.dss_data23 */ > + OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* GPIO_157 = lcd reset */ > + >; > + }; > + > + uart3_pins: pinmux_uart3_pins { > + pinctrl-single,pins = < > + OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ > + OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ > + >; > + }; > + > + led_pins: pinmux_leds_pins { > + pinctrl-single,pins = < > + OMAP3_CORE1_IOPAD(0x2154, PIN_OUTPUT | MUX_MODE4) /* GPIO_128 */ > + OMAP3_CORE1_IOPAD(0x2156, PIN_OUTPUT | MUX_MODE4) /* GPIO_129 */ > + OMAP3_CORE1_IOPAD(0x2190, PIN_OUTPUT | MUX_MODE4) /* GPIO_158 */ > + OMAP3_CORE1_IOPAD(0x2192, PIN_OUTPUT | MUX_MODE4) /* GPIO_159 */ > + >; > + }; > + > + button_pins: pinmux_button_pins { > + pinctrl-single,pins = < > + OMAP3_CORE1_IOPAD(0x2110, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_96 */ > + OMAP3_CORE1_IOPAD(0x2112, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_97 */ > + OMAP3_CORE1_IOPAD(0x2114, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_98 */ > + OMAP3_CORE1_IOPAD(0x2116, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_99 */ > + OMAP3_CORE1_IOPAD(0x2118, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_100 */ > + OMAP3_CORE1_IOPAD(0x211a, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_101 */ > + OMAP3_CORE1_IOPAD(0x211c, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_102 */ > + OMAP3_CORE1_IOPAD(0x211e, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_103 */ > + OMAP3_CORE1_IOPAD(0x2120, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_104 */ > + OMAP3_CORE1_IOPAD(0x2122, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_105 */ > + OMAP3_CORE1_IOPAD(0x2124, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_106 */ > + OMAP3_CORE1_IOPAD(0x2126, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_107 */ > + OMAP3_CORE1_IOPAD(0x2128, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_108 */ > + OMAP3_CORE1_IOPAD(0x212a, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_109 */ > + OMAP3_CORE1_IOPAD(0x212c, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_110 */ > + OMAP3_CORE1_IOPAD(0x212e, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_111 */ > + OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_176 */ We should not set pullups for all the buttons, they all have external pullups. > + >; > + }; > + > + penirq_pins: pinmux_penirq_pins { > + pinctrl-single,pins = < > + /* here we could enable to wakeup the cpu from suspend by a pen touch */ > + OMAP3_CORE1_IOPAD(0x210c, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_94 */ Again, we already have external pullup, no need to waste power. ... > + > +&mmc1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&mmc1_pins>; > + vmmc-supply = <&vmmc1>; > + bus-width = <4>; > + cd-gpios = <&twl_gpio 0 GPIO_ACTIVE_LOW>; > + wp-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>; /* GPIO_126 */ Large number of pandoras have defective write potect pins. Kernel used to not support write protect at all, so we noticed it too late. If it's possible to omit this it would be better do so, perhaps with a comment, or I can send a patch later... > +}; > + > +&mmc2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&mmc2_pins>; > + vmmc-supply = <&vmmc2>; > + bus-width = <4>; > + cd-gpios = <&twl_gpio 1 GPIO_ACTIVE_HIGH>; > + wp-gpios = <&gpio4 31 GPIO_ACTIVE_LOW>; /* GPIO_127 */ same here Gražvydas ^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 1/4] ARM: dts: omap3-pandora: add common device tree 2015-02-12 17:47 ` Grazvydas Ignotas @ 2015-02-12 20:09 ` Dr. H. Nikolaus Schaller 0 siblings, 0 replies; 14+ messages in thread From: Dr. H. Nikolaus Schaller @ 2015-02-12 20:09 UTC (permalink / raw) To: Grazvydas Ignotas, Marek Belisko Cc: Tony Lindgren, Benoit Cousson, Mark Rutland, devicetree, Russell King - ARM Linux, Pawel Moll, Ian Campbell, linux-kernel@vger.kernel.org, Rob Herring, Kumar Gala, linux-omap@vger.kernel.org, linux-arm-kernel@lists.infradead.org Am 12.02.2015 um 18:47 schrieb Grazvydas Ignotas <notasas@gmail.com>: > On Thu, Feb 12, 2015 at 3:03 PM, Marek Belisko <marek@goldelico.com> wrote: >> From: "H. Nikolaus Schaller" <hns@goldelico.com> >> >> This device tree allows to boot, supports the panel, >> framebuffer, touch screen, as well as some more peripherals. >> Since there is a OMAP3530 based 600 MHz variant and a DM3730 based >> 1 GHz variant we must include this common device tree code >> in one of two CPU specific device trees. >> >> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> >> Signed-off-by: Marek Belisko <marek@goldelico.com> >> --- >> arch/arm/boot/dts/omap3-pandora-common.dtsi | 641 ++++++++++++++++++++++++++++ >> 1 file changed, 641 insertions(+) >> create mode 100644 arch/arm/boot/dts/omap3-pandora-common.dtsi >> >> diff --git a/arch/arm/boot/dts/omap3-pandora-common.dtsi b/arch/arm/boot/dts/omap3-pandora-common.dtsi >> new file mode 100644 >> index 0000000..0a2a878 >> --- /dev/null >> +++ b/arch/arm/boot/dts/omap3-pandora-common.dtsi >> @@ -0,0 +1,641 @@ > > ... > >> + >> + gpio-leds { >> + >> + compatible = "gpio-leds"; >> + >> + pinctrl-names = "default"; >> + pinctrl-0 = <&led_pins>; >> + >> + led@1 { >> + label = "pandora::sd1"; >> + gpios = <&gpio5 0 GPIO_ACTIVE_HIGH>; /* GPIO_128 */ >> + linux,default-trigger = "mmc0"; >> + default-state = "off"; >> + }; >> + >> + led@2 { >> + label = "pandora::sd2"; >> + gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>; /* GPIO_129 */ >> + linux,default-trigger = "mmc1"; >> + default-state = "off"; >> + }; >> + >> + led@3 { >> + label = "pandora::bluetooth"; >> + gpios = <&gpio5 30 GPIO_ACTIVE_HIGH>; /* GPIO_158 */ >> + linux,default-trigger = "heartbeat"; > > I’d prefer this had no trigger, but no strong feelings here. Ok. Well, this is more or less our testing setup - so that we did see something before we could fix the display setup. I think practice will show what is better, and then it can be patched. We are at the beginning of Pandora DT work… > >> + default-state = "off"; >> + }; >> + >> + led@4 { >> + label = "pandora::wifi"; >> + gpios = <&gpio5 31 GPIO_ACTIVE_HIGH>; /* GPIO_159 */ >> + linux,default-trigger = "mmc2"; >> + default-state = "off"; >> + }; >> + }; >> + >> + gpio-keys { >> + compatible = "gpio-keys"; >> + >> + pinctrl-names = "default"; >> + pinctrl-0 = <&button_pins>; >> + >> + up-button { >> + label = "up"; >> + linux,code = <KEY_UP>; >> + gpios = <&gpio4 14 GPIO_ACTIVE_HIGH>; /* GPIO_110 */ >> + gpio-key,wakeup; >> + }; >> + >> + down-button { >> + label = "down"; >> + linux,code = <KEY_DOWN>; >> + gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* GPIO_103 */ >> + gpio-key,wakeup; >> + }; >> + >> + left-button { >> + label = "left"; >> + linux,code = <KEY_LEFT>; >> + gpios = <&gpio4 0 GPIO_ACTIVE_HIGH>; /* GPIO_96 */ >> + gpio-key,wakeup; >> + }; >> + >> + right-button { >> + label = "right"; >> + linux,code = <KEY_RIGHT>; >> + gpios = <&gpio4 2 GPIO_ACTIVE_HIGH>; /* GPIO_98 */ >> + gpio-key,wakeup; >> + }; >> + >> + pageup-button { >> + label = "game 1"; >> + linux,code = <KEY_PAGEUP>; >> + gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>; /* GPIO_109 */ >> + gpio-key,wakeup; >> + }; >> + >> + pagedown-button { >> + label = "game 3"; >> + linux,code = <KEY_PAGEDOWN>; >> + gpios = <&gpio4 10 GPIO_ACTIVE_HIGH>; /* GPIO_106 */ >> + gpio-key,wakeup; >> + }; >> + >> + home-button { >> + label = "game 4"; >> + linux,code = <KEY_HOME>; >> + gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>; /* GPIO_101 */ >> + gpio-key,wakeup; >> + }; >> + >> + end-button { >> + label = "game 2"; >> + linux,code = <KEY_END>; >> + gpios = <&gpio4 15 GPIO_ACTIVE_HIGH>; /* GPIO_111 */ >> + gpio-key,wakeup; >> + }; >> + >> + right-shift { >> + label = "l"; >> + linux,code = <KEY_RIGHTSHIFT>; >> + gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* GPIO_102 */ >> + gpio-key,wakeup; >> + }; >> + >> + kp-plus { >> + label = "l2"; >> + linux,code = <KEY_KPPLUS>; >> + gpios = <&gpio4 1 GPIO_ACTIVE_HIGH>; /* GPIO_97 */ >> + gpio-key,wakeup; >> + }; >> + >> + right-ctrl { >> + label = "r"; >> + linux,code = <KEY_RIGHTCTRL>; >> + gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>; /* GPIO_105 */ >> + gpio-key,wakeup; >> + }; >> + >> + kp-minus { >> + label = "r2"; >> + linux,code = <KEY_KPMINUS>; >> + gpios = <&gpio4 11 GPIO_ACTIVE_HIGH>; /* GPIO_107 */ >> + gpio-key,wakeup; >> + }; >> + >> + left-ctrl { >> + label = "ctrl"; >> + linux,code = <KEY_LEFTCTRL>; >> + gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* GPIO_104 */ >> + gpio-key,wakeup; >> + }; >> + >> + menu { >> + label = "menu"; >> + linux,code = <KEY_MENU>; >> + gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>; /* GPIO_99 */ >> + gpio-key,wakeup; >> + }; >> + >> + hold { >> + label = "hold"; >> + linux,code = <KEY_COFFEE>; >> + gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>; /* GPIO_176 */ >> + gpio-key,wakeup; >> + }; >> + >> + left-alt { >> + label = "alt"; >> + linux,code = <KEY_LEFTALT>; >> + gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>; /* GPIO_100 */ >> + gpio-key,wakeup; >> + }; >> + >> + lid { >> + label = "lid"; >> + linux,code = <0x00>; /* SW_LID lid shut */ >> + linux,input-type = <0x05>; /* EV_SW */ >> + gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>; /* GPIO_108 */ >> + gpio-key,wakeup; >> + }; > > This is not right, all button GPIOs are active low except GPIO_100, > which is active high. Well, I didn’t notice a difference - but here we should do it right. > GPIO_108 should not have the wakeup flag set > because lid switch power is normally cut during low power modes. Ah, you are right. It is VSIM powered. > > ... > >> + >> + dss_dpi_pins: pinmux_dss_dpi_pins { >> + pinctrl-single,pins = < >> + OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */ >> + OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */ >> + OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */ >> + OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */ >> + OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0) /* dss_data0.dss_data0 */ >> + OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0) /* dss_data1.dss_data1 */ >> + OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE0) /* dss_data2.dss_data2 */ >> + OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE0) /* dss_data3.dss_data3 */ >> + OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE0) /* dss_data4.dss_data4 */ >> + OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE0) /* dss_data5.dss_data5 */ >> + OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */ >> + OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */ >> + OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */ >> + OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */ >> + OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */ >> + OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */ >> + OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */ >> + OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */ >> + OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */ >> + OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */ >> + OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */ >> + OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */ >> + OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE0) /* dss_data18.dss_data18 */ >> + OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE0) /* dss_data19.dss_data19 */ >> + OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE0) /* dss_data20.dss_data20 */ >> + OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE0) /* dss_data21.dss_data21 */ >> + OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE0) /* dss_data22.dss_data22 */ >> + OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE0) /* dss_data23.dss_data23 */ >> + OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* GPIO_157 = lcd reset */ >> + >; >> + }; >> + >> + uart3_pins: pinmux_uart3_pins { >> + pinctrl-single,pins = < >> + OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ >> + OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ >> + >; >> + }; >> + >> + led_pins: pinmux_leds_pins { >> + pinctrl-single,pins = < >> + OMAP3_CORE1_IOPAD(0x2154, PIN_OUTPUT | MUX_MODE4) /* GPIO_128 */ >> + OMAP3_CORE1_IOPAD(0x2156, PIN_OUTPUT | MUX_MODE4) /* GPIO_129 */ >> + OMAP3_CORE1_IOPAD(0x2190, PIN_OUTPUT | MUX_MODE4) /* GPIO_158 */ >> + OMAP3_CORE1_IOPAD(0x2192, PIN_OUTPUT | MUX_MODE4) /* GPIO_159 */ >> + >; >> + }; >> + >> + button_pins: pinmux_button_pins { >> + pinctrl-single,pins = < >> + OMAP3_CORE1_IOPAD(0x2110, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_96 */ >> + OMAP3_CORE1_IOPAD(0x2112, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_97 */ >> + OMAP3_CORE1_IOPAD(0x2114, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_98 */ >> + OMAP3_CORE1_IOPAD(0x2116, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_99 */ >> + OMAP3_CORE1_IOPAD(0x2118, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_100 */ >> + OMAP3_CORE1_IOPAD(0x211a, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_101 */ >> + OMAP3_CORE1_IOPAD(0x211c, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_102 */ >> + OMAP3_CORE1_IOPAD(0x211e, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_103 */ >> + OMAP3_CORE1_IOPAD(0x2120, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_104 */ >> + OMAP3_CORE1_IOPAD(0x2122, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_105 */ >> + OMAP3_CORE1_IOPAD(0x2124, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_106 */ >> + OMAP3_CORE1_IOPAD(0x2126, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_107 */ >> + OMAP3_CORE1_IOPAD(0x2128, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_108 */ >> + OMAP3_CORE1_IOPAD(0x212a, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_109 */ >> + OMAP3_CORE1_IOPAD(0x212c, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_110 */ >> + OMAP3_CORE1_IOPAD(0x212e, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_111 */ >> + OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_176 */ > > We should not set pullups for all the buttons, they all have external pullups. Well, if they are active low, unless a button is pressed it does not matter. If a button is pressed we have 100k and ~30k in parallel giving approx. 80uA. Anyways, we should take your recommendation. > >> + >; >> + }; >> + >> + penirq_pins: pinmux_penirq_pins { >> + pinctrl-single,pins = < >> + /* here we could enable to wakeup the cpu from suspend by a pen touch */ >> + OMAP3_CORE1_IOPAD(0x210c, PIN_INPUT_PULLUP | MUX_MODE4) /* GPIO_94 */ > > Again, we already have external pullup, no need to waste power. Ok. > > ... > >> + >> +&mmc1 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&mmc1_pins>; >> + vmmc-supply = <&vmmc1>; >> + bus-width = <4>; >> + cd-gpios = <&twl_gpio 0 GPIO_ACTIVE_LOW>; >> + wp-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>; /* GPIO_126 */ > > Large number of pandoras have defective write potect pins. Kernel used > to not support write protect at all, so we noticed it too late. If > it's possible to omit this it would be better do so, perhaps with a > comment, or I can send a patch later… I think in this case you should send a patch later because you best can describe the problem in the commit message. > >> +}; >> + >> +&mmc2 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&mmc2_pins>; >> + vmmc-supply = <&vmmc2>; >> + bus-width = <4>; >> + cd-gpios = <&twl_gpio 1 GPIO_ACTIVE_HIGH>; >> + wp-gpios = <&gpio4 31 GPIO_ACTIVE_LOW>; /* GPIO_127 */ > > same here > > > Gražvydas BR, Nikolaus ^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH 2/4] ARM: dts: omap3-pandora: add OMAP3530 600 MHz version 2015-02-12 13:03 [PATCH 0/4] add openpandora device support Marek Belisko 2015-02-12 13:03 ` [PATCH 1/4] ARM: dts: omap3-pandora: add common device tree Marek Belisko @ 2015-02-12 13:03 ` Marek Belisko 2015-02-12 16:53 ` Tony Lindgren 2015-02-12 13:03 ` [PATCH 3/4] ARM: dts: omap3-pandora: add DM3730 1 GHz version Marek Belisko ` (2 subsequent siblings) 4 siblings, 1 reply; 14+ messages in thread From: Marek Belisko @ 2015-02-12 13:03 UTC (permalink / raw) To: tony, bcousson Cc: robh+dt, pawel.moll, mark.rutland, ijc+devicetree, galak, devicetree, linux, linux-arm-kernel, linux-kernel, linux-omap, marek, H. Nikolaus Schaller From: "H. Nikolaus Schaller" <hns@goldelico.com> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> --- arch/arm/boot/dts/omap3-pandora-600mhz.dts | 65 ++++++++++++++++++++++++++++++ 1 file changed, 65 insertions(+) create mode 100644 arch/arm/boot/dts/omap3-pandora-600mhz.dts diff --git a/arch/arm/boot/dts/omap3-pandora-600mhz.dts b/arch/arm/boot/dts/omap3-pandora-600mhz.dts new file mode 100644 index 0000000..7a51b04 --- /dev/null +++ b/arch/arm/boot/dts/omap3-pandora-600mhz.dts @@ -0,0 +1,65 @@ +/* + * Copyright (C) 2015 + * Nikolaus Schaller <hns@goldelico.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * device tree for OpenPandora with OMAP3530 + */ + +/dts-v1/; + +#include "omap34xx.dtsi" +#include "omap3-pandora-common.dtsi" + +/ { + model = "Pandora Handheld Console"; + + compatible = "ti,omap3"; +}; + +&omap3_pmx_core2 { + + pinctrl-names = "default"; + pinctrl-0 = < + &hsusb2_2_pins + &control_pins + >; + + hsusb2_2_pins: pinmux_hsusb2_2_pins { + pinctrl-single,pins = < + OMAP3430_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */ + OMAP3430_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */ + OMAP3430_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */ + OMAP3430_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */ + OMAP3430_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */ + OMAP3430_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */ + >; + }; + + mmc3_pins: pinmux_mmc3_pins { + pinctrl-single,pins = < + OMAP3430_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_clk.sdmmc3_clk */ + OMAP3430_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_ctl.sdmmc3_cmd */ + OMAP3430_CORE2_IOPAD(0x25e2, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d3.sdmmc3_dat3 */ + OMAP3430_CORE2_IOPAD(0x25e4, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d4.sdmmc3_dat0 */ + OMAP3430_CORE2_IOPAD(0x25e6, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d5.sdmmc3_dat1 */ + OMAP3430_CORE2_IOPAD(0x25e8, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d6.sdmmc3_dat2 */ + >; + }; + + control_pins: pinmux_control_pins { + pinctrl-single,pins = < + OMAP3430_CORE2_IOPAD(0x25dc, PIN_INPUT_PULLDOWN | MUX_MODE4) /* etk_d0.gpio_14 = HP_SHUTDOWN */ + OMAP3430_CORE2_IOPAD(0x25de, PIN_OUTPUT | MUX_MODE4) /* etk_d1.gpio_15 = BT_SHUTDOWN */ + OMAP3430_CORE2_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE4) /* etk_d2.gpio_16 = RESET_USB_HOST */ + OMAP3430_CORE2_IOPAD(0x25ea, PIN_INPUT_PULLUP | MUX_MODE4) /* etk_d7.gpio_21 = WIFI IRQ */ + OMAP3430_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4) /* etk_d8.gpio_22 = MSECURE */ + OMAP3430_CORE2_IOPAD(0x25ee, PIN_OUTPUT | MUX_MODE4) /* etk_d9.gpio_23 = WIFI_POWER */ + >; + }; +}; -- 1.9.1 ^ permalink raw reply related [flat|nested] 14+ messages in thread
* Re: [PATCH 2/4] ARM: dts: omap3-pandora: add OMAP3530 600 MHz version 2015-02-12 13:03 ` [PATCH 2/4] ARM: dts: omap3-pandora: add OMAP3530 600 MHz version Marek Belisko @ 2015-02-12 16:53 ` Tony Lindgren 0 siblings, 0 replies; 14+ messages in thread From: Tony Lindgren @ 2015-02-12 16:53 UTC (permalink / raw) To: Marek Belisko Cc: mark.rutland, devicetree, linux, pawel.moll, ijc+devicetree, H. Nikolaus Schaller, linux-kernel, robh+dt, bcousson, galak, linux-omap, linux-arm-kernel * Marek Belisko <marek@goldelico.com> [150212 05:07]: > From: "H. Nikolaus Schaller" <hns@goldelico.com> Can you please add a patch description for the board varian patches? Thanks, Tony ^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH 3/4] ARM: dts: omap3-pandora: add DM3730 1 GHz version 2015-02-12 13:03 [PATCH 0/4] add openpandora device support Marek Belisko 2015-02-12 13:03 ` [PATCH 1/4] ARM: dts: omap3-pandora: add common device tree Marek Belisko 2015-02-12 13:03 ` [PATCH 2/4] ARM: dts: omap3-pandora: add OMAP3530 600 MHz version Marek Belisko @ 2015-02-12 13:03 ` Marek Belisko 2015-02-12 23:10 ` Grazvydas Ignotas 2015-02-12 13:03 ` [PATCH 4/4] ARM: dts: omap3-pandora: include in dts Makefile Marek Belisko 2015-02-12 14:35 ` [PATCH 0/4] add openpandora device support Grazvydas Ignotas 4 siblings, 1 reply; 14+ messages in thread From: Marek Belisko @ 2015-02-12 13:03 UTC (permalink / raw) To: tony, bcousson Cc: robh+dt, pawel.moll, mark.rutland, ijc+devicetree, galak, devicetree, linux, linux-arm-kernel, linux-kernel, linux-omap, marek, H. Nikolaus Schaller From: "H. Nikolaus Schaller" <hns@goldelico.com> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> --- arch/arm/boot/dts/omap3-pandora-1ghz.dts | 65 ++++++++++++++++++++++++++++++++ 1 file changed, 65 insertions(+) create mode 100644 arch/arm/boot/dts/omap3-pandora-1ghz.dts diff --git a/arch/arm/boot/dts/omap3-pandora-1ghz.dts b/arch/arm/boot/dts/omap3-pandora-1ghz.dts new file mode 100644 index 0000000..6286f41 --- /dev/null +++ b/arch/arm/boot/dts/omap3-pandora-1ghz.dts @@ -0,0 +1,65 @@ +/* + * Copyright (C) 2015 + * Nikolaus Schaller <hns@goldelico.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * device tree for OpenPandora 1GHz with DM3730 + */ + +/dts-v1/; + +#include "omap36xx.dtsi" +#include "omap3-pandora-common.dtsi" + +/ { + model = "Pandora Handheld Console 1GHz"; + + compatible = "ti,omap36xx", "ti,omap3"; +}; + +&omap3_pmx_core2 { + + pinctrl-names = "default"; + pinctrl-0 = < + &hsusb2_2_pins + &control_pins + >; + + hsusb2_2_pins: pinmux_hsusb2_2_pins { + pinctrl-single,pins = < + OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */ + OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */ + OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */ + OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */ + OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */ + OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */ + >; + }; + + mmc3_pins: pinmux_mmc3_pins { + pinctrl-single,pins = < + OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_clk.sdmmc3_clk */ + OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_ctl.sdmmc3_cmd */ + OMAP3630_CORE2_IOPAD(0x25e2, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d3.sdmmc3_dat3 */ + OMAP3630_CORE2_IOPAD(0x25e4, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d4.sdmmc3_dat0 */ + OMAP3630_CORE2_IOPAD(0x25e6, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d5.sdmmc3_dat1 */ + OMAP3630_CORE2_IOPAD(0x25e8, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d6.sdmmc3_dat2 */ + >; + }; + + control_pins: pinmux_control_pins { + pinctrl-single,pins = < + OMAP3630_CORE2_IOPAD(0x25dc, PIN_INPUT_PULLDOWN | MUX_MODE4) /* etk_d0.gpio_14 = HP_SHUTDOWN */ + OMAP3630_CORE2_IOPAD(0x25de, PIN_OUTPUT | MUX_MODE4) /* etk_d1.gpio_15 = BT_SHUTDOWN */ + OMAP3630_CORE2_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE4) /* etk_d2.gpio_16 = RESET_USB_HOST */ + OMAP3630_CORE2_IOPAD(0x25ea, PIN_INPUT_PULLUP | MUX_MODE4) /* etk_d7.gpio_21 = WIFI IRQ */ + OMAP3630_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4) /* etk_d8.gpio_22 = MSECURE */ + OMAP3630_CORE2_IOPAD(0x25ee, PIN_OUTPUT | MUX_MODE4) /* etk_d9.gpio_23 = WIFI_POWER */ + >; + }; +}; -- 1.9.1 ^ permalink raw reply related [flat|nested] 14+ messages in thread
* Re: [PATCH 3/4] ARM: dts: omap3-pandora: add DM3730 1 GHz version 2015-02-12 13:03 ` [PATCH 3/4] ARM: dts: omap3-pandora: add DM3730 1 GHz version Marek Belisko @ 2015-02-12 23:10 ` Grazvydas Ignotas 0 siblings, 0 replies; 14+ messages in thread From: Grazvydas Ignotas @ 2015-02-12 23:10 UTC (permalink / raw) To: Marek Belisko Cc: Tony Lindgren, bcousson, Mark Rutland, devicetree, pawel.moll, ijc+devicetree, H. Nikolaus Schaller, linux-kernel@vger.kernel.org, robh+dt, galak, linux-omap@vger.kernel.org On Thu, Feb 12, 2015 at 3:03 PM, Marek Belisko <marek@goldelico.com> wrote: > From: "H. Nikolaus Schaller" <hns@goldelico.com> > > Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> > --- > arch/arm/boot/dts/omap3-pandora-1ghz.dts | 65 ++++++++++++++++++++++++++++++++ > 1 file changed, 65 insertions(+) > create mode 100644 arch/arm/boot/dts/omap3-pandora-1ghz.dts > > diff --git a/arch/arm/boot/dts/omap3-pandora-1ghz.dts b/arch/arm/boot/dts/omap3-pandora-1ghz.dts > new file mode 100644 > index 0000000..6286f41 > --- /dev/null > +++ b/arch/arm/boot/dts/omap3-pandora-1ghz.dts ... > + > + control_pins: pinmux_control_pins { > + pinctrl-single,pins = < > + OMAP3630_CORE2_IOPAD(0x25dc, PIN_INPUT_PULLDOWN | MUX_MODE4) /* etk_d0.gpio_14 = HP_SHUTDOWN */ > + OMAP3630_CORE2_IOPAD(0x25de, PIN_OUTPUT | MUX_MODE4) /* etk_d1.gpio_15 = BT_SHUTDOWN */ > + OMAP3630_CORE2_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE4) /* etk_d2.gpio_16 = RESET_USB_HOST */ > + OMAP3630_CORE2_IOPAD(0x25ea, PIN_INPUT_PULLUP | MUX_MODE4) /* etk_d7.gpio_21 = WIFI IRQ */ The WG7210 document claims that no pulldown/pullup is needed, and we always had it disabled. The mainline wl1251 driver also reconfigures that signal to be active high on wl1251 side, and uses rising edge interrupts (I don't know why it does that). > + OMAP3630_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4) /* etk_d8.gpio_22 = MSECURE */ > + OMAP3630_CORE2_IOPAD(0x25ee, PIN_OUTPUT | MUX_MODE4) /* etk_d9.gpio_23 = WIFI_POWER */ I think we also need these here: OMAP3_WKUP_IOPAD(0x2a54, PIN_INPUT | MUX_MODE4) /* reserved.gpio_127 = MMC2_WP */ OMAP3_WKUP_IOPAD(0x2a56, PIN_INPUT | MUX_MODE4) /* reserved.gpio_126 = MMC1_WP */ OMAP3_WKUP_IOPAD(0x2a58, PIN_OUTPUT | MUX_MODE4) /* reserved.gpio_128 = LED_MMC1 */ OMAP3_WKUP_IOPAD(0x2a5a, PIN_OUTPUT | MUX_MODE4) /* reserved.gpio_129 = LED_MMC2 */ Gražvydas ^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH 4/4] ARM: dts: omap3-pandora: include in dts Makefile 2015-02-12 13:03 [PATCH 0/4] add openpandora device support Marek Belisko ` (2 preceding siblings ...) 2015-02-12 13:03 ` [PATCH 3/4] ARM: dts: omap3-pandora: add DM3730 1 GHz version Marek Belisko @ 2015-02-12 13:03 ` Marek Belisko 2015-02-12 16:04 ` Tony Lindgren 2015-02-12 14:35 ` [PATCH 0/4] add openpandora device support Grazvydas Ignotas 4 siblings, 1 reply; 14+ messages in thread From: Marek Belisko @ 2015-02-12 13:03 UTC (permalink / raw) To: tony, bcousson Cc: robh+dt, pawel.moll, mark.rutland, ijc+devicetree, galak, devicetree, linux, linux-arm-kernel, linux-kernel, linux-omap, marek, H. Nikolaus Schaller From: "H. Nikolaus Schaller" <hns@goldelico.com> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> --- arch/arm/boot/dts/Makefile | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 91bd5bd..69f3106 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -343,6 +343,8 @@ dtb-$(CONFIG_ARCH_OMAP3) += am3517-craneboard.dtb \ omap3-overo-storm-tobi.dtb \ omap3-overo-summit.dtb \ omap3-overo-tobi.dtb \ + omap3-pandora-600mhz.dtb \ + omap3-pandora-1ghz.dtb \ omap3-sbc-t3517.dtb \ omap3-sbc-t3530.dtb \ omap3-sbc-t3730.dtb \ -- 1.9.1 ^ permalink raw reply related [flat|nested] 14+ messages in thread
* Re: [PATCH 4/4] ARM: dts: omap3-pandora: include in dts Makefile 2015-02-12 13:03 ` [PATCH 4/4] ARM: dts: omap3-pandora: include in dts Makefile Marek Belisko @ 2015-02-12 16:04 ` Tony Lindgren 0 siblings, 0 replies; 14+ messages in thread From: Tony Lindgren @ 2015-02-12 16:04 UTC (permalink / raw) To: Marek Belisko Cc: mark.rutland, devicetree, linux, pawel.moll, ijc+devicetree, H. Nikolaus Schaller, linux-kernel, robh+dt, bcousson, galak, linux-omap, linux-arm-kernel * Marek Belisko <marek@goldelico.com> [150212 05:07]: > From: "H. Nikolaus Schaller" <hns@goldelico.com> > > Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> > --- > arch/arm/boot/dts/Makefile | 2 ++ > 1 file changed, 2 insertions(+) > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 91bd5bd..69f3106 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -343,6 +343,8 @@ dtb-$(CONFIG_ARCH_OMAP3) += am3517-craneboard.dtb \ > omap3-overo-storm-tobi.dtb \ > omap3-overo-summit.dtb \ > omap3-overo-tobi.dtb \ > + omap3-pandora-600mhz.dtb \ > + omap3-pandora-1ghz.dtb \ > omap3-sbc-t3517.dtb \ > omap3-sbc-t3530.dtb \ > omap3-sbc-t3730.dtb \ This change you can fold into patches 3 and 4 :) Regards, Tony ^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 0/4] add openpandora device support 2015-02-12 13:03 [PATCH 0/4] add openpandora device support Marek Belisko ` (3 preceding siblings ...) 2015-02-12 13:03 ` [PATCH 4/4] ARM: dts: omap3-pandora: include in dts Makefile Marek Belisko @ 2015-02-12 14:35 ` Grazvydas Ignotas 4 siblings, 0 replies; 14+ messages in thread From: Grazvydas Ignotas @ 2015-02-12 14:35 UTC (permalink / raw) To: Marek Belisko Cc: Tony Lindgren, bcousson, Mark Rutland, devicetree, pawel.moll, ijc+devicetree, linux-kernel@vger.kernel.org, robh+dt, galak, linux-omap@vger.kernel.org, linux-arm-kernel@lists.infradead.org On Thu, Feb 12, 2015 at 3:03 PM, Marek Belisko <marek@goldelico.com> wrote: > This series of patches adds initial device tree support for the > OpenPandora. The most important parts are working (display, keyboard, > touch, charging, fuel gauge, musb port, sd/mmc ports, leds, buttons). > Not yet supported are: usb host port, nubs, wifi, bluetooth, audio. > > First patch add common dtsi file which is then used in 600mhz and 1ghz > variants of openpandora which support is added in patches 2 and 3. Nice, thanks for those patches. There is also a OMAP3530 variant with 256MB of RAM (otherwise identical to 512MB OMAP3530) that the legacy board file supports, over 1000 such units were made. Could we also have support for that? I guess that will make 4 pandora related .dts files... Gražvydas ^ permalink raw reply [flat|nested] 14+ messages in thread
end of thread, other threads:[~2015-02-12 23:10 UTC | newest] Thread overview: 14+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2015-02-12 13:03 [PATCH 0/4] add openpandora device support Marek Belisko 2015-02-12 13:03 ` [PATCH 1/4] ARM: dts: omap3-pandora: add common device tree Marek Belisko 2015-02-12 16:03 ` Tony Lindgren 2015-02-12 16:29 ` Dr. H. Nikolaus Schaller 2015-02-12 16:52 ` Tony Lindgren 2015-02-12 17:47 ` Grazvydas Ignotas 2015-02-12 20:09 ` Dr. H. Nikolaus Schaller 2015-02-12 13:03 ` [PATCH 2/4] ARM: dts: omap3-pandora: add OMAP3530 600 MHz version Marek Belisko 2015-02-12 16:53 ` Tony Lindgren 2015-02-12 13:03 ` [PATCH 3/4] ARM: dts: omap3-pandora: add DM3730 1 GHz version Marek Belisko 2015-02-12 23:10 ` Grazvydas Ignotas 2015-02-12 13:03 ` [PATCH 4/4] ARM: dts: omap3-pandora: include in dts Makefile Marek Belisko 2015-02-12 16:04 ` Tony Lindgren 2015-02-12 14:35 ` [PATCH 0/4] add openpandora device support Grazvydas Ignotas
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).