Re: [PATCH v4 0/3] Add CAMSS support for SM6350

["Luca Weiss" <luca.weiss@fairphone.com>]

Hi Vladimir,

On Tue Mar 31, 2026 at 12:49 AM CEST, Vladimir Zapolskiy wrote:
> Hi Luca,
>
> On 2/16/26 10:54, Luca Weiss wrote:
>> Add bindings, driver and dts to support the Camera Subsystem on the
>> SM6350 SoC.
>> 
>> These patches were tested on a Fairphone 4 smartphone with WIP sensor
>> drivers (Sony IMX576 and IMX582), the camera pipeline works properly as
>> far as I can tell.
>> 
>> Though when stopping the camera stream, the following clock warning
>> appears in dmesg. But it does not interfere with any functionality,
>> starting and stopping the stream works and debugcc is showing 426.4 MHz
>> while the clock is on, and 'off' while it's off.
>> 
>> Any suggestion how to fix this, is appreciated.
>
> I've looked at CAMCC recently, and I do notice that SM6350 CAMCC does not
> set '.use_rpm = true' flag for whatever reason.
>
> If you find a free minute, can you test the change below?..

Unfortunately that change does not resolve the "gcc_camera_axi_clk
status stuck at 'on'" warning.

fairphone-fp4:~$ cat /sys/bus/platform/drivers/sm6350-camcc/ad00000.clock-controller/power/runtime_status 
active

fairphone-fp4:~$ cat /sys/bus/platform/drivers/sm6350-camcc/ad00000.clock-controller/power/runtime_status
suspended

>
> ----8<----
> diff --git a/drivers/clk/qcom/camcc-sm6350.c b/drivers/clk/qcom/camcc-sm6350.c
> index 7df12c1311c6..ba880e4edcaf 100644
> --- a/drivers/clk/qcom/camcc-sm6350.c
> +++ b/drivers/clk/qcom/camcc-sm6350.c
> @@ -1880,6 +1880,7 @@ static const struct qcom_cc_desc camcc_sm6350_desc = {
>   	.num_clks = ARRAY_SIZE(camcc_sm6350_clocks),
>   	.gdscs = camcc_sm6350_gdscs,
>   	.num_gdscs = ARRAY_SIZE(camcc_sm6350_gdscs),
> +	.use_rpm = true,
>   };
>   
>   static const struct of_device_id camcc_sm6350_match_table[] = {
> ----8<----
>
> This change could be considered to be included in any case, I believe.

I guess this change is now the way to enable pm_runtime, I had this
series 3 years ago in February 2023:
https://lore.kernel.org/linux-arm-msm/20230213-sm6350-camcc-runtime_pm-v3-0-d35e0d833cc4@fairphone.com/

But I never followed up due to me not understanding pm_runtime well and
no direct need for it.

But I guess reviving that with use_rpm = true, add power-domains &
required-opps to dt-bindings and sm6350.dtsi should be a good idea?

Regards
Luca

>
>> [ 5738.590980] ------------[ cut here ]------------
>> [ 5738.591009] gcc_camera_axi_clk status stuck at 'on'
>> [ 5738.591049] WARNING: CPU: 0 PID: 6918 at drivers/clk/qcom/clk-branch.c:87 clk_branch_toggle+0x170/0x190
>> [ 5738.591081] Modules linked in:
>> [ 5738.591099] CPU: 0 UID: 10000 PID: 6918 Comm: plasma-camera Tainted: G        W           6.17.0-00057-ge6b67db49622 #71 NONE
>> [ 5738.591118] Tainted: [W]=WARN
>> [ 5738.591126] Hardware name: Fairphone 4 (DT)
>> [ 5738.591136] pstate: 604000c5 (nZCv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
>> [ 5738.591150] pc : clk_branch_toggle+0x170/0x190
>> [ 5738.591164] lr : clk_branch_toggle+0x170/0x190
>> [ 5738.591177] sp : ffff800086ed3980
>> [ 5738.591184] x29: ffff800086ed3990 x28: 0000000000000001 x27: ffff800086ed3cd8
>> [ 5738.591208] x26: 0000000000000000 x25: ffffda14fcfbd250 x24: 0000000000000000
>> [ 5738.591230] x23: 0000000000000000 x22: ffffda14fc38bce0 x21: 0000000000000000
>> [ 5738.591252] x20: ffffda14fd33e618 x19: 0000000000000000 x18: 00000000000064c8
>> [ 5738.591274] x17: 0000000000000000 x16: 00001ae003667e9e x15: ffffda14fd2a07b0
>> [ 5738.591295] x14: 0000000000000000 x13: 6f27207461206b63 x12: 7574732073757461
>> [ 5738.591317] x11: 0000000000000058 x10: 0000000000000018 x9 : ffffda14fd2a0838
>> [ 5738.591338] x8 : 0000000000057fa8 x7 : 0000000000000a16 x6 : ffffda14fd2f8838
>> [ 5738.591360] x5 : ffff0001f6f59788 x4 : 0000000000000a15 x3 : ffff25ecf9d7e000
>> [ 5738.591381] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff0000baf5c100
>> [ 5738.591403] Call trace:
>> [ 5738.591412]  clk_branch_toggle+0x170/0x190 (P)
>> [ 5738.591429]  clk_branch2_disable+0x1c/0x30
>> [ 5738.591445]  clk_core_disable+0x5c/0xb4
>> [ 5738.591462]  clk_disable+0x38/0x60
>> [ 5738.591478]  camss_disable_clocks+0x44/0x78
>> [ 5738.591496]  vfe_put+0x7c/0xc0
>> [ 5738.591512]  vfe_set_power+0x40/0x50
>> [ 5738.591528]  pipeline_pm_power_one+0x14c/0x150
>> [ 5738.591546]  pipeline_pm_power+0x74/0xf4
>> [ 5738.591561]  v4l2_pipeline_pm_use+0x54/0x9c
>> [ 5738.591577]  v4l2_pipeline_pm_put+0x14/0x40
>> [ 5738.591592]  video_unprepare_streaming+0x18/0x24
>> [ 5738.591608]  __vb2_queue_cancel+0x4c/0x314
>> [ 5738.591626]  vb2_core_streamoff+0x24/0xc8
>> [ 5738.591643]  vb2_ioctl_streamoff+0x58/0x98
>> [ 5738.591657]  v4l_streamoff+0x24/0x30
>> [ 5738.591672]  __video_do_ioctl+0x430/0x4a8
>> [ 5738.591689]  video_usercopy+0x2ac/0x680
>> [ 5738.591705]  video_ioctl2+0x18/0x40
>> [ 5738.591720]  v4l2_ioctl+0x40/0x60
>> [ 5738.591734]  __arm64_sys_ioctl+0x90/0xf0
>> [ 5738.591750]  invoke_syscall.constprop.0+0x40/0xf0
>> [ 5738.591769]  el0_svc_common.constprop.0+0x38/0xd8
>> [ 5738.591785]  do_el0_svc+0x1c/0x28
>> [ 5738.591801]  el0_svc+0x34/0xe8
>> [ 5738.591820]  el0t_64_sync_handler+0xa0/0xe4
>> [ 5738.591838]  el0t_64_sync+0x198/0x19c
>> [ 5738.591854] ---[ end trace 0000000000000000 ]---
>> 
>> Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
>> ---
>> Changes in v4:
>> - Update power-domain-names order (Krzysztof)
>> - Make hex numbers lower case in init seq (David)
>> - Pick up tags
>> - Link to v3: https://lore.kernel.org/r/20260213-sm6350-camss-v3-0-30a845b0b7cc@fairphone.com
>
> Should find some time myself to issue RBs, sorry for the delay.
>
>> Changes in v3:
>> - Update dt-bindings to include everything related to camss
>> - Update regulator names
>> - Remove slow_ahb_src
>> - Link to v2: https://lore.kernel.org/r/20251114-sm6350-camss-v2-0-d1ff67da33b6@fairphone.com
>> 
>> Changes in v2:
>> - Remove prefix from interconnect-names
>> - Move 'top' power-domain to the top of list
>> - Update regulator supply names
>> - Link to v1: https://lore.kernel.org/r/20251024-sm6350-camss-v1-0-63d626638add@fairphone.com
>> 
>> ---
>> Luca Weiss (3):
>>        dt-bindings: media: camss: Add qcom,sm6350-camss
>>        media: qcom: camss: Add SM6350 support
>>        arm64: dts: qcom: sm6350: Add CAMSS node
>> 
>>   .../bindings/media/qcom,sm6350-camss.yaml          | 471 +++++++++++++++++++++
>>   arch/arm64/boot/dts/qcom/sm6350.dtsi               | 233 ++++++++++
>>   .../platform/qcom/camss/camss-csiphy-3ph-1-0.c     | 125 ++++++
>>   drivers/media/platform/qcom/camss/camss-vfe.c      |   2 +
>>   drivers/media/platform/qcom/camss/camss.c          | 261 ++++++++++++
>>   drivers/media/platform/qcom/camss/camss.h          |   1 +
>>   6 files changed, 1093 insertions(+)
>> ---
>> base-commit: 3daf23347bb5f4a375d0101ed29c97ce1a99721b
>> change-id: 20251024-sm6350-camss-9c404bf9cfdd
>> 
>> Best regards,