[PATCH v2 2/2] ASoC: cs43130: Add devicetree bindings for CS43130

Li Xu
2017-08-18T16:00:20Z

Add devicetree bindings documentation file for Cirrus
Logic CS43130 codec.

Signed-off-by: Li Xu <li.xu@cirrus.com>
---
.../devicetree/bindings/sound/cs43130.txt | 67 ++++++++++++++++++++++
1 file changed, 67 insertions(+)
create mode 100644 Documentation/devicetree/bindings/sound/cs43130.txt

diff --git a/Documentation/devicetree/bindings/sound/cs43130.txt b/Documentation/devicetree/bindings/sound/cs43130.txt
new file mode 100644
index 0000000..8b1dd5a
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/cs43130.txt
@@ -0,0 +1,67 @@
+CS43130 DAC
+
+Required properties:
+
+ - compatible : "cirrus,cs43130", "cirrus,cs4399", "cirrus,cs43131",
+ "cirrus,cs43198"
+
+ - reg : the I2C address of the device for I2C
+
+ - VA-supply, VP-supply, VL-supply, VCP-supply, VD-supply:
+ power supplies for the device, as covered in
+ Documentation/devicetree/bindings/regulator/regulator.txt.
+
+
+Optional properties:
+
+ - reset-gpios : Active low GPIO used to reset the device
+
+ - cirrus,xtal-ibias:
+ When external MCLK is generated by external crystal
+ oscillator, CS43130 can be used to provide bias current
+ for external crystal. Amount of bias current sent is
+ set as:
+ 1 = 7.5uA
+ 2 = 12.5uA
+ 3 = 15uA
+
+ - cirrus,dc-measure:
+ Boolean, define to enable headphone DC impedance measurement.
+
+ - cirrus,ac-measure:
+ Boolean, define to enable headphone AC impedance measurement.
+ DC impedance must also be enabled for AC impedance measurement.
+
+ - cirrus,dc-threshold:
+ Define 2 DC impedance thresholds in ohms for HP output control.
+ Default values are 50 and 120 Ohms.
+
+ - cirrus,ac-freq:
+ Define the frequencies at which to measure HP AC impedance.
+ Only used if "cirrus,dc-measure" is defined.
+ Exactly 10 frequencies must be defined.
+ If this properties is undefined, by default,
+ following frequencies are used:
+ <24 43 93 200 431 928 2000 4309 9283 20000>
+ The above frequencies are logarithmically equally spaced.
+ Log base is 10.
+
+Example:
+
+cs43130: audio-codec@30 {
+ compatible = "cirrus,cs43130";
+ reg = <0x30>;
+ reset-gpios = <&axi_gpio 54 0>;
+ VA-supply = <&dummy_vreg>;
+ VP-supply = <&dummy_vreg>;
+ VL-supply = <&dummy_vreg>;
+ VCP-supply = <&dummy_vreg>;
+ VD-supply = <&dummy_vreg>;
+ cirrus,xtal-ibias = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <55 8>;
+ cirrus,dc-measure;
+ cirrus,ac-measure;
+ cirrus,dc-threshold = /bits/ 16 <20 100>;
+ cirrus,ac-freq = /bits/ 16 <24 43 93 200 431 928 2000 4309 9283 20000>;
+};
--
1.9.1