[PATCH 5/7] mfd: arizona: Remove audio bindings from MFD binding document

Charles Keepax
2017-09-04T15:41:52Z

Now the audio bindings have their own binding document update the main
MFD document to point to that file and remove the audio binding
documentation.

Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
---
Documentation/devicetree/bindings/mfd/arizona.txt | 40 +----------------------
1 file changed, 1 insertion(+), 39 deletions(-)

diff --git a/Documentation/devicetree/bindings/mfd/arizona.txt b/Documentation/devicetree/bindings/mfd/arizona.txt
index b37bdde5cfda..bdd017686ea5 100644
--- a/Documentation/devicetree/bindings/mfd/arizona.txt
+++ b/Documentation/devicetree/bindings/mfd/arizona.txt
@@ -65,45 +65,6 @@ Optional properties:
a value that is out of range for a 16 bit register then the chip default
will be used. If present exactly five values must be specified.

- - wlf,inmode : A list of INn_MODE register values, where n is the number
- of input signals. Valid values are 0 (Differential), 1 (Single-ended) and
- 2 (Digital Microphone). If absent, INn_MODE registers set to 0 by default.
- If present, values must be specified less than or equal to the number of
- input signals. If values less than the number of input signals, elements
- that have not been specified are set to 0 by default. Entries are:
- <IN1, IN2, IN3, IN4> (wm5102, wm5110, wm8280, wm8997)
- <IN1A, IN2A, IN1B, IN2B> (wm8998, wm1814)
- - wlf,out-mono : A list of boolean values indicating whether each output is
- mono or stereo. Position within the list indicates the output affected
- (eg. First entry in the list corresponds to output 1). A non-zero value
- indicates a mono output. If present, the number of values should be less
- than or equal to the number of outputs, if less values are supplied the
- additional outputs will be treated as stereo.
-
- - wlf,dmic-ref : DMIC reference voltage source for each input, can be
- selected from either MICVDD or one of the MICBIAS's, defines
- (ARIZONA_DMIC_xxxx) are provided in <dt-bindings/mfd/arizona.txt>. If
- present, the number of values should be less than or equal to the
- number of inputs, unspecified inputs will use the chip default.
-
- - wlf,max-channels-clocked : The maximum number of channels to be clocked on
- each AIF, useful for I2S systems with multiple data lines being mastered.
- Specify one cell for each AIF to be configured, specify zero for AIFs that
- should be handled normally.
- If present, number of cells must be less than or equal to the number of
- AIFs. If less than the number of AIFs, for cells that have not been
- specified the corresponding AIFs will be treated as default setting.
-
- - wlf,spk-fmt : PDM speaker data format, must contain 2 cells (OUT5 and OUT6).
- See the datasheet for values.
- The second cell is ignored for codecs that do not have OUT6 (wm5102, wm8997,
- wm8998, wm1814)
-
- - wlf,spk-mute : PDM speaker mute setting, must contain 2 cells (OUT5 and OUT6).
- See the datasheet for values.
- The second cell is ignored for codecs that do not have OUT6 (wm5102, wm8997,
- wm8998, wm1814)
-
- DCVDD-supply, MICVDD-supply : Power supplies, only need to be specified if
they are being externally supplied. As covered in
Documentation/devicetree/bindings/regulator/regulator.txt
@@ -112,6 +73,7 @@ Optional properties:
Also see child specific device properties:
Regulator - ../regulator/arizona-regulator.txt
Extcon - ../extcon/extcon-arizona.txt
+ Sound - ../sound/arizona.txt

Example:

--
2.11.0