Re: [PATCH v4 7/8] arm64: dts: qcom: sm8550: Add USB PHYs and controller nodes

[Abel Vesa <abel.vesa@linaro.org>]

On 23-02-03 11:55:11, Johan Hovold wrote:
> On Thu, Feb 02, 2023 at 03:25:10PM +0200, Abel Vesa wrote:
> > Add USB host controller and PHY nodes.
> > 
> > Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
> > ---
> > 
> > Changes since v3:
> >  * none
> > 
> > Changes since v2:
> >  * none
> > 
> > NOTE: This patch has been already merged. It is here only to provide
> > context for the rest of the patchset. There is a change with respect to
> > the clocks, but that will be sent as a separate/individual fix patch.
> 
> I believe it was because of the 'phy' and 'common' resets, which have
> been switched below.

No, the resets haven't been switched, at least not compared to the
already merged version.

> 
> >  arch/arm64/boot/dts/qcom/sm8550.dtsi | 92 +++++++++++++++++++++++++++-
> >  1 file changed, 91 insertions(+), 1 deletion(-)
> > 
> > diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi
> > index a85d2ae7d155..0262193e2ffe 100644
> > --- a/arch/arm64/boot/dts/qcom/sm8550.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi
> > @@ -14,6 +14,7 @@
> >  #include <dt-bindings/mailbox/qcom-ipcc.h>
> >  #include <dt-bindings/power/qcom-rpmpd.h>
> >  #include <dt-bindings/soc/qcom,rpmh-rsc.h>
> > +#include <dt-bindings/phy/phy-qcom-qmp.h>
> >  #include <dt-bindings/thermal/thermal.h>
> >  
> >  / {
> > @@ -746,7 +747,7 @@ gcc: clock-controller@100000 {
> >  				 <&ufs_mem_phy 0>,
> >  				 <&ufs_mem_phy 1>,
> >  				 <&ufs_mem_phy 2>,
> > -				 <0>;
> > +				 <&usb_dp_qmpphy QMP_USB43DP_USB3_PIPE_CLK>;
> >  		};
> >  
> >  		ipcc: mailbox@408000 {
> > @@ -2060,6 +2061,95 @@ opp-202000000 {
> >  			};
> >  		};
> >  
> > +		usb_1_hsphy: phy@88e3000 {
> > +			compatible = "qcom,sm8550-snps-eusb2-phy";
> > +			reg = <0x0 0x088e3000 0x0 0x154>;
> > +			#phy-cells = <0>;
> > +
> > +			clocks = <&tcsr TCSR_USB2_CLKREF_EN>;
> > +			clock-names = "ref";
> > +
> > +			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
> > +
> > +			status = "disabled";
> > +		};
> > +
> > +		usb_dp_qmpphy: phy@88e8000 {
> > +			compatible = "qcom,sm8550-qmp-usb3-dp-phy";
> > +			reg = <0x0 0x088e8000 0x0 0x3000>;
> > +
> > +			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
> > +				 <&rpmhcc RPMH_CXO_CLK>,
> > +				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
> > +				 <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
> > +			clock-names = "aux", "ref", "com_aux", "usb3_pipe";
> > +
> > +			power-domains = <&gcc USB3_PHY_GDSC>;
> > +
> > +			resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>,
> > +				 <&gcc GCC_USB3_PHY_PRIM_BCR>;
> > +			reset-names = "phy", "common";
> > +
> > +			#clock-cells = <1>;
> > +			#phy-cells = <1>;
> > +
> > +			status = "disabled";
> > +		};
> 
> Johan